[PATCH v2 0/3] arm64: qcom: add Ayaneo Pocket DS gaming console

Linux ARM-MSM sub-architecture
 help / color / mirror / Atom feed

* [PATCH v2 0/3] arm64: qcom: add Ayaneo Pocket DS gaming console
@ 2026-05-11 11:33 Alexandre Hamamdjian via B4 Relay
  2026-05-11 11:33 ` [PATCH v2 1/3] dt-bindings: arm: qcom: document the Ayaneo Pocket DS Alexandre Hamamdjian via B4 Relay
                   ` (2 more replies)
  0 siblings, 3 replies; 10+ messages in thread
From: Alexandre Hamamdjian via B4 Relay @ 2026-05-11 11:33 UTC (permalink / raw)
  To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley
  Cc: linux-arm-msm, devicetree, linux-kernel, Alexandre Hamamdjian,
	Teguh Sobirin

This series adds initial support for the Ayaneo Pocket DS, a handheld
gaming console built around the Qualcomm QCS8550 SoC. It has UFS
storage, WiFi/Bluetooth, gaming buttons, microSD, dual displays, and
USB-C with DisplayPort. Game controls are exposed through a Renesas
uPD720201 PCIe USB 3.0 host controller on PCIe1.

The first patch adds labels to the sm8550 thermal zones so the board
can attach its trip points and cooling maps through the &label override
syntax. The second introduces the Pocket DS device tree itself.

Only the basics are wired up at this stage (boot to console, core
peripherals, USB-C and DP); the display panel will follow in a later
submission.

Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
---
Changes in v2:
- Inlined the board into a single qcs8550-ayaneo-pocketds.dts, matching
  the sm8650-ayaneo-pocket-s2 layout
- Added qcom,qcs8550 to the compatible chain
- Prerequisite patch labelling the sm8550 thermal zones so the board
  can extend them via &label overrides (and refactored the board's
  thermal-zones to use them)
- Added the Renesas uPD720201 USB 3.0 controller as a child of pcie1
  with proper avdd33 / vdd10 / vdd33 regulators
- Moved gamepad_pwr_en off &pcie1's pinctrl-0 and onto the
  usb-controller node
- Split the lumped upd720201_active pinctrl into per-regulator states
- Fixed mdss_dp0_out data-lanes to <0 1 2 3> (all four wired)
- Fixed gpio-reserved-ranges to <32 4> (gpio 38-39 drive the Goodix
  touchscreen)
- Renamed nodes with underscores (llcc-lpi-region, splash-region,
  gpio@20) per DT conventions
- Reordered pinctrl-names after pinctrl-N file-wide
- Dropped the unused cont_splash_region label
- Link to v1: https://patch.msgid.link/20260510-pocketds-v1-0-cf05acec06af@gmail.com

---
Alexandre Hamamdjian (1):
      arm64: dts: qcom: sm8550: add labels for thermal zones

Teguh Sobirin (2):
      dt-bindings: arm: qcom: document the Ayaneo Pocket DS
      arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console

 Documentation/devicetree/bindings/arm/qcom.yaml    |    6 +
 arch/arm64/boot/dts/qcom/Makefile                  |    1 +
 .../boot/dts/qcom/qcs8550-ayaneo-pocketds.dts      | 1861 ++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sm8550.dtsi               |   26 +-
 4 files changed, 1881 insertions(+), 13 deletions(-)
---
base-commit: e98d21c170b01ddef366f023bbfcf6b31509fa83
change-id: 20260510-pocketds-e0e7b99cf369

Best regards,
--  
Alexandre Hamamdjian <azkali.limited@gmail.com>



^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 1/3] dt-bindings: arm: qcom: document the Ayaneo Pocket DS
  2026-05-11 11:33 [PATCH v2 0/3] arm64: qcom: add Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
@ 2026-05-11 11:33 ` Alexandre Hamamdjian via B4 Relay
  2026-05-14 12:20   ` Krzysztof Kozlowski
  2026-05-11 11:33 ` [PATCH v2 2/3] arm64: dts: qcom: sm8550: add labels for thermal zones Alexandre Hamamdjian via B4 Relay
  2026-05-11 11:33 ` [PATCH v2 3/3] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
  2 siblings, 1 reply; 10+ messages in thread
From: Alexandre Hamamdjian via B4 Relay @ 2026-05-11 11:33 UTC (permalink / raw)
  To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley
  Cc: linux-arm-msm, devicetree, linux-kernel, Alexandre Hamamdjian,
	Teguh Sobirin

From: Teguh Sobirin <teguh@sobir.in>

Document the Qualcomm QCS8550 based Ayaneo Pocket DS gaming console.

Co-developed-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
Signed-off-by: Teguh Sobirin <teguh@sobir.in>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 2741c07e9f41..f130a6b092b9 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1107,6 +1107,12 @@ properties:
           - const: qcom,qcs8550
           - const: qcom,sm8550
 
+      - items:
+          - enum:
+              - ayaneo,pocketds
+          - const: qcom,qcs8550
+          - const: qcom,sm8550
+
       - items:
           - enum:
               - ayaneo,pocket-s2

-- 
2.54.0



^ permalink raw reply related	[flat|nested] 10+ messages in thread

* Re: [PATCH v2 1/3] dt-bindings: arm: qcom: document the Ayaneo Pocket DS
  2026-05-11 11:33 ` [PATCH v2 1/3] dt-bindings: arm: qcom: document the Ayaneo Pocket DS Alexandre Hamamdjian via B4 Relay
@ 2026-05-14 12:20   ` Krzysztof Kozlowski
       [not found]     ` <CAL5cOWtRUs-XF5Y6+X-G3PVkGQp-ts+HTiAfzezVjQqYoyt1NQ@mail.gmail.com>
  0 siblings, 1 reply; 10+ messages in thread
From: Krzysztof Kozlowski @ 2026-05-14 12:20 UTC (permalink / raw)
  To: Alexandre Hamamdjian
  Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley, linux-arm-msm, devicetree, linux-kernel,
	Teguh Sobirin

On Mon, May 11, 2026 at 06:33:53PM +0700, Alexandre Hamamdjian wrote:
> From: Teguh Sobirin <teguh@sobir.in>
> 
> Document the Qualcomm QCS8550 based Ayaneo Pocket DS gaming console.
> 
> Co-developed-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
> Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
> Signed-off-by: Teguh Sobirin <teguh@sobir.in>

That's pretty messed DOC chain. I also wonder what was co-developed
exactly in this trivial binding...

Best regards,
Krzysztof


^ permalink raw reply	[flat|nested] 10+ messages in thread

[parent not found: <CAL5cOWtRUs-XF5Y6+X-G3PVkGQp-ts+HTiAfzezVjQqYoyt1NQ@mail.gmail.com>]

* Re: [PATCH v2 1/3] dt-bindings: arm: qcom: document the Ayaneo Pocket DS
       [not found]     ` <CAL5cOWtRUs-XF5Y6+X-G3PVkGQp-ts+HTiAfzezVjQqYoyt1NQ@mail.gmail.com>
@ 2026-05-14 12:31       ` Krzysztof Kozlowski
  0 siblings, 0 replies; 10+ messages in thread
From: Krzysztof Kozlowski @ 2026-05-14 12:31 UTC (permalink / raw)
  To: Alexandre Hamamdjian
  Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley, linux-arm-msm, devicetree, linux-kernel,
	Teguh Sobirin

On 14/05/2026 14:24, Alexandre Hamamdjian wrote:
> The DT was adapted by myself to fit the upstream standards and one bug was
> fixed too.

Do not top post.

Do we talk about DT here?

Best regards,
Krzysztof

^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 2/3] arm64: dts: qcom: sm8550: add labels for thermal zones
  2026-05-11 11:33 [PATCH v2 0/3] arm64: qcom: add Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
  2026-05-11 11:33 ` [PATCH v2 1/3] dt-bindings: arm: qcom: document the Ayaneo Pocket DS Alexandre Hamamdjian via B4 Relay
@ 2026-05-11 11:33 ` Alexandre Hamamdjian via B4 Relay
  2026-05-11 12:55   ` Neil Armstrong
  2026-05-14 12:26   ` Krzysztof Kozlowski
  2026-05-11 11:33 ` [PATCH v2 3/3] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
  2 siblings, 2 replies; 10+ messages in thread
From: Alexandre Hamamdjian via B4 Relay @ 2026-05-11 11:33 UTC (permalink / raw)
  To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley
  Cc: linux-arm-msm, devicetree, linux-kernel, Alexandre Hamamdjian

From: Alexandre Hamamdjian <azkali.limited@gmail.com>

Add labels for the cpuss, cpu and gpuss thermal zones so board files
can extend them with trip points and cooling maps through the &label
override syntax, instead of redeclaring the zones by path.

Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
---
 arch/arm64/boot/dts/qcom/sm8550.dtsi | 26 +++++++++++++-------------
 1 file changed, 13 insertions(+), 13 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 912525e9bca6..a9c678fc9cb2 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -5764,7 +5764,7 @@ reset-mon-config {
 			};
 		};
 
-		cpuss0-thermal {
+		cpuss0_thermal: cpuss0-thermal {
 			thermal-sensors = <&tsens0 1>;
 
 			trips {
@@ -5782,7 +5782,7 @@ reset-mon-config {
 			};
 		};
 
-		cpuss1-thermal {
+		cpuss1_thermal: cpuss1-thermal {
 			thermal-sensors = <&tsens0 2>;
 
 			trips {
@@ -5800,7 +5800,7 @@ reset-mon-config {
 			};
 		};
 
-		cpuss2-thermal {
+		cpuss2_thermal: cpuss2-thermal {
 			thermal-sensors = <&tsens0 3>;
 
 			trips {
@@ -5818,7 +5818,7 @@ reset-mon-config {
 			};
 		};
 
-		cpuss3-thermal {
+		cpuss3_thermal: cpuss3-thermal {
 			thermal-sensors = <&tsens0 4>;
 
 			trips {
@@ -6028,7 +6028,7 @@ cpu6_bottom_crit: cpu-critical {
 			};
 		};
 
-		cpu7-top-thermal {
+		cpu7_top_thermal: cpu7-top-thermal {
 			thermal-sensors = <&tsens0 13>;
 
 			trips {
@@ -6536,7 +6536,7 @@ reset-mon-config {
 			};
 		};
 
-		gpuss-0-thermal {
+		gpuss0_thermal: gpuss-0-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 1>;
@@ -6569,7 +6569,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-1-thermal {
+		gpuss1_thermal: gpuss-1-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 2>;
@@ -6602,7 +6602,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-2-thermal {
+		gpuss2_thermal: gpuss-2-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 3>;
@@ -6635,7 +6635,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-3-thermal {
+		gpuss3_thermal: gpuss-3-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 4>;
@@ -6668,7 +6668,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-4-thermal {
+		gpuss4_thermal: gpuss-4-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 5>;
@@ -6701,7 +6701,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-5-thermal {
+		gpuss5_thermal: gpuss-5-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 6>;
@@ -6734,7 +6734,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-6-thermal {
+		gpuss6_thermal: gpuss-6-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 7>;
@@ -6767,7 +6767,7 @@ trip-point2 {
 			};
 		};
 
-		gpuss-7-thermal {
+		gpuss7_thermal: gpuss-7-thermal {
 			polling-delay-passive = <10>;
 
 			thermal-sensors = <&tsens2 8>;

-- 
2.54.0



^ permalink raw reply related	[flat|nested] 10+ messages in thread

* Re: [PATCH v2 2/3] arm64: dts: qcom: sm8550: add labels for thermal zones
  2026-05-11 11:33 ` [PATCH v2 2/3] arm64: dts: qcom: sm8550: add labels for thermal zones Alexandre Hamamdjian via B4 Relay
@ 2026-05-11 12:55   ` Neil Armstrong
  2026-05-14 12:26   ` Krzysztof Kozlowski
  1 sibling, 0 replies; 10+ messages in thread
From: Neil Armstrong @ 2026-05-11 12:55 UTC (permalink / raw)
  To: azkali.limited, Bjorn Andersson, Konrad Dybcio, Rob Herring,
	Krzysztof Kozlowski, Conor Dooley
  Cc: linux-arm-msm, devicetree, linux-kernel

On 5/11/26 13:33, Alexandre Hamamdjian via B4 Relay wrote:
> From: Alexandre Hamamdjian <azkali.limited@gmail.com>
> 
> Add labels for the cpuss, cpu and gpuss thermal zones so board files
> can extend them with trip points and cooling maps through the &label
> override syntax, instead of redeclaring the zones by path.
> 
> Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
> ---
>   arch/arm64/boot/dts/qcom/sm8550.dtsi | 26 +++++++++++++-------------
>   1 file changed, 13 insertions(+), 13 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> index 912525e9bca6..a9c678fc9cb2 100644
> --- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
> @@ -5764,7 +5764,7 @@ reset-mon-config {
>   			};
>   		};
>   
> -		cpuss0-thermal {
> +		cpuss0_thermal: cpuss0-thermal {
>   			thermal-sensors = <&tsens0 1>;
>   
>   			trips {
> @@ -5782,7 +5782,7 @@ reset-mon-config {
>   			};
>   		};
>   
> -		cpuss1-thermal {
> +		cpuss1_thermal: cpuss1-thermal {
>   			thermal-sensors = <&tsens0 2>;
>   
>   			trips {
> @@ -5800,7 +5800,7 @@ reset-mon-config {
>   			};
>   		};
>   
> -		cpuss2-thermal {
> +		cpuss2_thermal: cpuss2-thermal {
>   			thermal-sensors = <&tsens0 3>;
>   
>   			trips {
> @@ -5818,7 +5818,7 @@ reset-mon-config {
>   			};
>   		};
>   
> -		cpuss3-thermal {
> +		cpuss3_thermal: cpuss3-thermal {
>   			thermal-sensors = <&tsens0 4>;
>   
>   			trips {
> @@ -6028,7 +6028,7 @@ cpu6_bottom_crit: cpu-critical {
>   			};
>   		};
>   
> -		cpu7-top-thermal {
> +		cpu7_top_thermal: cpu7-top-thermal {
>   			thermal-sensors = <&tsens0 13>;
>   
>   			trips {
> @@ -6536,7 +6536,7 @@ reset-mon-config {
>   			};
>   		};
>   
> -		gpuss-0-thermal {
> +		gpuss0_thermal: gpuss-0-thermal {
>   			polling-delay-passive = <10>;
>   
>   			thermal-sensors = <&tsens2 1>;
> @@ -6569,7 +6569,7 @@ trip-point2 {
>   			};
>   		};
>   
> -		gpuss-1-thermal {
> +		gpuss1_thermal: gpuss-1-thermal {
>   			polling-delay-passive = <10>;
>   
>   			thermal-sensors = <&tsens2 2>;
> @@ -6602,7 +6602,7 @@ trip-point2 {
>   			};
>   		};
>   
> -		gpuss-2-thermal {
> +		gpuss2_thermal: gpuss-2-thermal {
>   			polling-delay-passive = <10>;
>   
>   			thermal-sensors = <&tsens2 3>;
> @@ -6635,7 +6635,7 @@ trip-point2 {
>   			};
>   		};
>   
> -		gpuss-3-thermal {
> +		gpuss3_thermal: gpuss-3-thermal {
>   			polling-delay-passive = <10>;
>   
>   			thermal-sensors = <&tsens2 4>;
> @@ -6668,7 +6668,7 @@ trip-point2 {
>   			};
>   		};
>   
> -		gpuss-4-thermal {
> +		gpuss4_thermal: gpuss-4-thermal {
>   			polling-delay-passive = <10>;
>   
>   			thermal-sensors = <&tsens2 5>;
> @@ -6701,7 +6701,7 @@ trip-point2 {
>   			};
>   		};
>   
> -		gpuss-5-thermal {
> +		gpuss5_thermal: gpuss-5-thermal {
>   			polling-delay-passive = <10>;
>   
>   			thermal-sensors = <&tsens2 6>;
> @@ -6734,7 +6734,7 @@ trip-point2 {
>   			};
>   		};
>   
> -		gpuss-6-thermal {
> +		gpuss6_thermal: gpuss-6-thermal {
>   			polling-delay-passive = <10>;
>   
>   			thermal-sensors = <&tsens2 7>;
> @@ -6767,7 +6767,7 @@ trip-point2 {
>   			};
>   		};
>   
> -		gpuss-7-thermal {
> +		gpuss7_thermal: gpuss-7-thermal {
>   			polling-delay-passive = <10>;
>   
>   			thermal-sensors = <&tsens2 8>;
> 

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>

Thanks,
Neil

^ permalink raw reply	[flat|nested] 10+ messages in thread

* Re: [PATCH v2 2/3] arm64: dts: qcom: sm8550: add labels for thermal zones
  2026-05-11 11:33 ` [PATCH v2 2/3] arm64: dts: qcom: sm8550: add labels for thermal zones Alexandre Hamamdjian via B4 Relay
  2026-05-11 12:55   ` Neil Armstrong
@ 2026-05-14 12:26   ` Krzysztof Kozlowski
  1 sibling, 0 replies; 10+ messages in thread
From: Krzysztof Kozlowski @ 2026-05-14 12:26 UTC (permalink / raw)
  To: Alexandre Hamamdjian
  Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley, linux-arm-msm, devicetree, linux-kernel

On Mon, May 11, 2026 at 06:33:54PM +0700, Alexandre Hamamdjian wrote:
> Add labels for the cpuss, cpu and gpuss thermal zones so board files
> can extend them with trip points and cooling maps through the &label
> override syntax, instead of redeclaring the zones by path.

Dead code if there is no user. You need a user of that labels in the
same patch.

Best regards,
Krzysztof


^ permalink raw reply	[flat|nested] 10+ messages in thread

* [PATCH v2 3/3] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console
  2026-05-11 11:33 [PATCH v2 0/3] arm64: qcom: add Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
  2026-05-11 11:33 ` [PATCH v2 1/3] dt-bindings: arm: qcom: document the Ayaneo Pocket DS Alexandre Hamamdjian via B4 Relay
  2026-05-11 11:33 ` [PATCH v2 2/3] arm64: dts: qcom: sm8550: add labels for thermal zones Alexandre Hamamdjian via B4 Relay
@ 2026-05-11 11:33 ` Alexandre Hamamdjian via B4 Relay
  2026-05-14 12:25   ` Krzysztof Kozlowski
  2 siblings, 1 reply; 10+ messages in thread
From: Alexandre Hamamdjian via B4 Relay @ 2026-05-11 11:33 UTC (permalink / raw)
  To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley
  Cc: linux-arm-msm, devicetree, linux-kernel, Alexandre Hamamdjian,
	Teguh Sobirin

From: Teguh Sobirin <teguh@sobir.in>

Add initial Device Tree for the Ayaneo Pocket DS gaming console based
on the Qualcomm QCS8550 platform.

The design is similar to a phone without the modem, the game control
is handled via a standalone controller connected to a Renesas uPD720201
PCIe USB 3.0 host controller. DisplayPort is muxed over the USB-C
connector with all four lanes wired.

Display panel support will be added in a second time.

Co-developed-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
Signed-off-by: Teguh Sobirin <teguh@sobir.in>
---
 arch/arm64/boot/dts/qcom/Makefile                  |    1 +
 .../boot/dts/qcom/qcs8550-ayaneo-pocketds.dts      | 1861 ++++++++++++++++++++
 2 files changed, 1862 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index cc42829f92eb..45859e977bc9 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -185,6 +185,7 @@ qcs8300-ride-el2-dtbs := qcs8300-ride.dtb monaco-el2.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8300-ride-el2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-aim300-aiot.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-ayaneo-pocketds.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride-r3.dtb
 
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocketds.dts b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocketds.dts
new file mode 100644
index 000000000000..9d32f64e6651
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocketds.dts
@@ -0,0 +1,1861 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Teguh Sobirin.
+ * Copyright (c) 2025, ROCKNIX (https://github.com/ROCKNIX)
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qcs8550.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550b.dtsi"
+#define PMK8550VE_SID 5
+#include "pm8550ve.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/delete-node/ &aop_image_mem;
+/delete-node/ &aop_config_mem;
+/delete-node/ &camera_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &mpss_dsm_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &q6_mpss_dtb_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &q6_cdsp_dtb_mem;
+
+/delete-node/ &remoteproc_mpss;
+/delete-node/ &remoteproc_cdsp;
+
+/ {
+	model = "AYANEO Pocket DS";
+	compatible = "ayaneo,pocketds", "qcom,qcs8550", "qcom,sm8550";
+	rocknix-u-boot-dt-id = "u-boot-pocket-ds";
+
+	aliases {
+		serial0 = &uart7;
+		serial1 = &uart14;
+		hsuart0 = &uart11;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	tca6424_vcc: regulator-tca6424-vcc {
+		compatible = "regulator-fixed";
+		regulator-name = "tca6424_vcc";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 168 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+		regulator-boot-on;
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_ts: vdd-ts {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_ts_en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&tca6408 1 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+	pmic-glink {
+		compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&redriver_ss_out>;
+					};
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		hyp_mem: hyp-region@80000000 {
+			reg = <0 0x80000000 0 0xa00000>;
+			no-map;
+		};
+
+		cpusys_vm_mem: cpusys-vm-region@80a00000 {
+			reg = <0 0x80a00000 0 0x400000>;
+			no-map;
+		};
+
+		hyp_tags_mem: hyp-tags-region@80e00000 {
+			reg = <0 0x80e00000 0 0x3d0000>;
+			no-map;
+		};
+
+		xbl_sc_mem: xbl-sc-region@d8100000 {
+			reg = <0 0xd8100000 0 0x40000>;
+			no-map;
+		};
+
+		hyp_tags_reserved_mem: hyp-tags-reserved-region@811d0000 {
+			reg = <0 0x811d0000 0 0x30000>;
+			no-map;
+		};
+
+		xbl_dt_log_merged_mem: xbl-dt-log-merged-region@81a00000 {
+			reg = <0 0x81a00000 0 0x260000>;
+			no-map;
+		};
+
+		aop_config_merged_mem: aop-config-merged-region@81c80000 {
+			reg = <0 0x81c80000 0 0x74000>;
+			no-map;
+		};
+
+		chipinfo_mem: chipinfo-region@81cf4000 {
+			reg = <0 0x81cf4000 0 0x1000>;
+			no-map;
+		};
+
+		global_sync_mem: global-sync-region@82600000 {
+			reg = <0 0x82600000 0 0x100000>;
+			no-map;
+		};
+
+		tz_stat_mem: tz-stat-region@82700000 {
+			reg = <0 0x82700000 0 0x100000>;
+			no-map;
+		};
+
+		cpucp_fw_mem: cpucp-fw-region@d8140000 {
+			reg = <0 0xd8140000 0 0x1c0000>;
+			no-map;
+		};
+
+		qtee_mem: qtee-region@d8300000 {
+			reg = <0 0xd8300000 0 0x500000>;
+			no-map;
+		};
+
+		hwfence_shbuf: hwfence-shbuf-region@e6440000 {
+			reg = <0 0xe6440000 0 0x2dd000>;
+			no-map;
+		};
+
+		hyp_ext_reserved_mem: hyp-ext-reserved-region@ff700000 {
+			reg = <0 0xff700000 0 0x100000>;
+			no-map;
+		};
+
+		llcc_lpi_mem: llcc-lpi-region@ff800000 {
+			reg = <0 0xff800000 0 0x600000>;
+			no-map;
+		};
+
+		hyp_ext_tags_mem: hyp-ext-tags-region@fce00000 {
+			reg = <0 0xfce00000 0 0x2900000>;
+			no-map;
+		};
+
+		splash_region: splash-region@b8000000 {
+			reg = <0x0 0xb8000000 0x0 0x2b00000>;
+			no-map;
+		};
+	};
+
+	sound {
+		compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
+		model = "SM8550-APS";
+		audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
+				"SpkrRight IN", "WSA_SPK2 OUT",
+				"VA DMIC0", "vdd-micb",
+				"VA DMIC1", "vdd-micb";
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&spk_amp_l>,
+					    <&spk_amp_r>,
+					    <&swr0 0>,
+					    <&lpass_wsamacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	vdd_fan_5v0: vdd-fan-5v0-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd_fan_5v0";
+
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&fan_pwr_active>;
+		pinctrl-names = "default";
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	upd720201_avdd33_reg: upd720201-avdd33-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "upd720201_avdd33";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		vin-supply = <&vph_pwr>;
+
+		pinctrl-0 = <&upd720201_avdd33>;
+		pinctrl-names = "default";
+	};
+
+	upd720201_vdd10_reg: upd720201-vdd10-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "upd720201_vdd10";
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+
+		gpios = <&tlmm 13 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		vin-supply = <&vph_pwr>;
+
+		pinctrl-0 = <&upd720201_vdd10>;
+		pinctrl-names = "default";
+	};
+
+	upd720201_vdd33_reg: upd720201-vdd33-regulator {
+		compatible = "regulator-fixed";
+
+		regulator-name = "upd720201_vdd33";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		vin-supply = <&vph_pwr>;
+
+		pinctrl-0 = <&upd720201_vdd33>;
+		pinctrl-names = "default";
+	};
+
+	pwm_fan: pwm-fan {
+		compatible = "pwm-fan";
+
+		pinctrl-0 = <&fan_pwm_active>, <&fan_int>;
+		pinctrl-names = "default", "sleep";
+
+		fan-supply = <&vdd_fan_5v0>;
+		pwms = <&pm8550_pwm 3 40000>;
+		interrupt-parent = <&tlmm>;
+		interrupts = <64 IRQ_TYPE_EDGE_FALLING>;
+
+		#cooling-cells = <2>;
+		cooling-levels = <0 30 45 60 70 90 120 150>;
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		pinctrl-0 = <&wlan_en>, <&bt_default>, <&pmk8550_sleep_clk>;
+		pinctrl-names = "default";
+
+		wlan-enable-gpios = <&tlmm 80 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&vreg_s5g_0p85>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_s2g_0p85>;
+		vdddig-supply = <&vreg_s4e_0p95>;
+		vddrfa1p2-supply = <&vreg_s4g_1p25>;
+		vddrfa1p8-supply = <&vreg_s6g_1p86>;
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+};
+
+&cpuss0_thermal {
+	polling-delay = <200>;
+
+	trips {
+		cpuss0_fan0: trip-point2 {
+			temperature = <40000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss0_fan1: trip-point3 {
+			temperature = <50000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss0_fan2: trip-point4 {
+			temperature = <60000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss0_fan3: trip-point5 {
+			temperature = <65000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss0_fan4: trip-point6 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss0_fan5: trip-point7 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss0_fan6: trip-point8 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&cpuss1_thermal {
+	polling-delay = <200>;
+
+	trips {
+		cpuss1_fan0: trip-point2 {
+			temperature = <40000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss1_fan1: trip-point3 {
+			temperature = <50000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss1_fan2: trip-point4 {
+			temperature = <60000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss1_fan3: trip-point5 {
+			temperature = <65000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss1_fan4: trip-point6 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss1_fan5: trip-point7 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss1_fan6: trip-point8 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&cpuss2_thermal {
+	polling-delay = <200>;
+
+	trips {
+		cpuss2_fan0: trip-point2 {
+			temperature = <40000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss2_fan1: trip-point3 {
+			temperature = <50000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss2_fan2: trip-point4 {
+			temperature = <60000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss2_fan3: trip-point5 {
+			temperature = <65000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss2_fan4: trip-point6 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss2_fan5: trip-point7 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss2_fan6: trip-point8 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&cpuss3_thermal {
+	polling-delay = <200>;
+
+	trips {
+		cpuss3_fan0: trip-point2 {
+			temperature = <40000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss3_fan1: trip-point3 {
+			temperature = <50000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss3_fan2: trip-point4 {
+			temperature = <60000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss3_fan3: trip-point5 {
+			temperature = <65000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss3_fan4: trip-point6 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss3_fan5: trip-point7 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpuss3_fan6: trip-point8 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&cpu7_top_thermal {
+	polling-delay = <200>;
+
+	trips {
+		cpu7_top_fan0: trip-point2 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpu7_top_fan1: trip-point3 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		cpu7_top_fan2: trip-point4 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&gpuss0_thermal {
+	polling-delay = <200>;
+
+	trips {
+		gpuss0_fan0: trip-point3 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss0_fan1: trip-point4 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss0_fan2: trip-point5 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&gpuss1_thermal {
+	polling-delay = <200>;
+
+	trips {
+		gpuss1_fan0: trip-point3 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss1_fan1: trip-point4 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss1_fan2: trip-point5 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&gpuss2_thermal {
+	polling-delay = <200>;
+
+	trips {
+		gpuss2_fan0: trip-point3 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss2_fan1: trip-point4 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss2_fan2: trip-point5 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&gpuss3_thermal {
+	polling-delay = <200>;
+
+	trips {
+		gpuss3_fan0: trip-point3 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss3_fan1: trip-point4 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss3_fan2: trip-point5 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&gpuss4_thermal {
+	polling-delay = <200>;
+
+	trips {
+		gpuss4_fan0: trip-point3 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss4_fan1: trip-point4 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss4_fan2: trip-point5 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&gpuss5_thermal {
+	polling-delay = <200>;
+
+	trips {
+		gpuss5_fan0: trip-point3 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss5_fan1: trip-point4 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss5_fan2: trip-point5 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&gpuss6_thermal {
+	polling-delay = <200>;
+
+	trips {
+		gpuss6_fan0: trip-point3 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss6_fan1: trip-point4 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss6_fan2: trip-point5 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+&gpuss7_thermal {
+	polling-delay = <200>;
+
+	trips {
+		gpuss7_fan0: trip-point3 {
+			temperature = <70000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss7_fan1: trip-point4 {
+			temperature = <75000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+
+		gpuss7_fan2: trip-point5 {
+			temperature = <80000>;
+			hysteresis = <3000>;
+			type = "passive";
+		};
+	};
+};
+
+/* DMIC 01 23 */
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+	pinctrl-names = "default";
+	vdd-micb-supply = <&vreg_l10b_1p8>;
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob1>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l11-supply = <&vreg_s4g_1p25>;
+		vdd-l12-supply = <&vreg_s6g_1p86>;
+		vdd-l15-supply = <&vreg_s6g_1p86>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2720000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p1: ldo5 {
+			regulator-name = "vreg_l5b_3p1";
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_1p8: ldo7 {
+			regulator-name = "vreg_l7b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_1p8: ldo8 {
+			regulator-name = "vreg_l8b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_1p8: ldo10 {
+			regulator-name = "vreg_l10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11b_1p2: ldo11 {
+			regulator-name = "vreg_l11b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p8: ldo12 {
+			regulator-name = "vreg_l12b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p2: ldo14 {
+			regulator-name = "vreg_l14b_3p2";
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16b_2p8: ldo16 {
+			regulator-name = "vreg_l16b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s4g_1p25>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+
+		vreg_l3c_0p9: ldo3 {
+			regulator-name = "vreg_l3c_0p9";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+
+		vreg_l1d_0p88: ldo1 {
+			regulator-name = "vreg_l1d_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vreg_s4e_0p95: smps4 {
+			regulator-name = "vreg_s4e_0p95";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <984000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5e_1p08: smps5 {
+			regulator-name = "vreg_s5e_1p08";
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1120000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1e_0p88: ldo1 {
+			regulator-name = "vreg_l1e_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2e_0p9: ldo2 {
+			regulator-name = "vreg_l2e_0p9";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <970000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s4f_0p5: smps4 {
+			regulator-name = "vreg_s4f_0p5";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <700000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1f_0p9: ldo1 {
+			regulator-name = "vreg_l1f_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_0p88: ldo2 {
+			regulator-name = "vreg_l2f_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_0p88: ldo3 {
+			regulator-name = "vreg_l3f_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-5 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "g";
+		vdd-l1-supply = <&vreg_s4g_1p25>;
+		vdd-l2-supply = <&vreg_s4g_1p25>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+
+		vreg_s1g_1p25: smps1 {
+			regulator-name = "vreg_s1g_1p25";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2g_0p85: smps2 {
+			regulator-name = "vreg_s2g_0p85";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s3g_0p8: smps3 {
+			regulator-name = "vreg_s3g_0p8";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4g_1p25: smps4 {
+			regulator-name = "vreg_s4g_1p25";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1352000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5g_0p85: smps5 {
+			regulator-name = "vreg_s5g_0p85";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s6g_1p86: smps6 {
+			regulator-name = "vreg_s6g_1p86";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1g_1p2: ldo1 {
+			regulator-name = "vreg_l1g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3g_1p2: ldo3 {
+			regulator-name = "vreg_l3g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&pm8550_gpios {
+	sdc2_card_det_n: sdc2-card-det-n-state {
+		pins = "gpio12";
+		function = "normal";
+		input-enable;
+		output-disable;
+		bias-pull-up;
+		power-source = <1>;
+	};
+
+	volume_up_n: volume-up-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+
+	fan_pwm_active: fan-pwm-active-state {
+		pins = "gpio9";
+		function = "func1";
+		output-low;
+		bias-disable;
+		power-source = <0>;
+		qcom,drive-strength = <3>; /* PMIC_GPIO_STRENGTH_LOW */
+	};
+};
+
+&pmk8550_gpios {
+	pmk8550_sleep_clk: sleep-clk-state {
+		pins = "gpio3";
+		function = "func1";
+		input-disable;
+		output-enable;
+		bias-disable;
+		power-source = <0>;
+	};
+};
+
+&pm8550b_eusb2_repeater {
+	vdd18-supply = <&vreg_l15b_1p8>;
+	vdd3-supply = <&vreg_l5b_3p1>;
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+
+	status = "okay";
+};
+
+&pmk8550_rtc {
+	nvmem-cells = <&rtc_offset>;
+	nvmem-cell-names = "offset";
+};
+
+&pmk8550_sdam_2 {
+	rtc_offset: rtc-offset@bc {
+		reg = <0xbc 0x4>;
+	};
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+
+	/* AYANEO Controller serial interface */
+	uart11: serial@88c000 {
+		compatible = "qcom,geni-uart";
+		reg = <0 0x0088c000 0 0x4000>;
+		clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+		clock-names = "se";
+		pinctrl-0 = <&qup_uart11_default>;
+		pinctrl-names = "default";
+		interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH 0>;
+		interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
+				 &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
+				<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
+				 &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ACTIVE_ONLY>;
+		interconnect-names = "qup-core", "qup-config";
+		operating-points-v2 = <&qup_opp_table_100mhz>;
+		power-domains = <&rpmhpd RPMHPD_CX>;
+
+		status = "okay";
+	};
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8550/ayaneo/adsp.mdt",
+			"qcom/sm8550/ayaneo/adsp_dtb.mdt";
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+	vmmc-supply = <&vreg_l9b_2p9>;
+	vqmmc-supply = <&vreg_l8b_1p8>;
+	no-sdio;
+	no-mmc;
+
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	sd-uhs-ddr50;
+
+	qcom,dll-config = <0x0007442c>;
+	sdhci-caps-mask = <0x3 0x0>;
+
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32764>;
+};
+
+&swr0 {
+	status = "okay";
+
+	spk_amp_l: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+
+		pinctrl-0 = <&spkr_1_sd_n_active>;
+		pinctrl-names = "default";
+
+		powerdown-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
+
+		vdd-1p8-supply = <&vreg_l10b_1p8>;
+		vdd-io-supply = <&vreg_l10b_1p8>;
+
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	spk_amp_r: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+
+		pinctrl-0 = <&spkr_2_sd_n_active>;
+		pinctrl-names = "default";
+
+		powerdown-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+
+		vdd-1p8-supply = <&vreg_l10b_1p8>;
+		vdd-io-supply = <&vreg_l10b_1p8>;
+
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <32 4>;
+
+	bt_default: bt-default-state {
+		bt-en-pins {
+			pins = "gpio81";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+		};
+
+		sw-ctrl-pins {
+			pins = "gpio82";
+			function = "gpio";
+			bias-pull-down;
+		};
+	};
+
+	fan_pwr_active: fan-pwr-active-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	fan_int: fan-int-state {
+		pins = "gpio64";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	upd720201_avdd33: upd720201-avdd33-state {
+		pins = "gpio10";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	upd720201_vdd10: upd720201-vdd10-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	upd720201_vdd33: upd720201-vdd33-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	gamepad_pwr_en: gamepad-pwr-en-active-state {
+		pins = "gpio52";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	qup_uart11_default: qup-uart11-default-state {
+		/* TX, RX */
+		pins = "gpio70", "gpio71";
+		function = "qup2_se3";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	sde_dsi_active: sde-dsi-active-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+		output-high;
+	};
+
+	sde_dsi_suspend: sde-dsi-suspend-state {
+		pins = "gpio133";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	sde_te_active: sde-te-active-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	sde_te_suspend: sde-te-suspend-state {
+		pins = "gpio86";
+		function = "mdp_vsync";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	wlan_en: wlan-en-state {
+		pins = "gpio80";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-down;
+	};
+
+	spkr_1_sd_n_active: spkr-1-sd-n-active-state {
+		pins = "gpio7";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-high;
+	};
+
+	spkr_2_sd_n_active: spkr-2-sd-n-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-high;
+	};
+
+	panel_pwr_active: panel-pwr-active-state {
+		pins = "gpio152", "gpio153";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+		output-high;
+	};
+
+	sde_dsi1_active: sde-dsi1-active-state {
+		pins = "gpio137";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+		output-high;
+	};
+
+	sde_dsi1_suspend: sde-dsi1-suspend-state {
+		pins = "gpio137";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-down;
+	};
+
+	ts_rst_default: ts-rst-default-state {
+		pins = "gpio24";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	ts_rst_sleep: ts-rst-sleep-state {
+		pins = "gpio24";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	ts_int_default: ts-int-default-state {
+		pins = "gpio25";
+		function = "gpio";
+		bias-pull-up;
+		drive-strength = <8>;
+	};
+
+	ts_int_sleep: ts-int-sleep-state {
+		pins = "gpio25";
+		function = "gpio";
+		bias-pull-down;
+		drive-strength = <2>;
+	};
+
+	ts2_irq: ts2-irq-state {
+		pins = "gpio39";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-disable;
+	};
+
+	ts2_reset: ts2-reset-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-down;
+	};
+};
+
+&pm8550_pwm {
+	status = "okay";
+};
+
+&xo_board {
+	clock-frequency = <76800000>;
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&gpi_dma2 {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/sm8550/a740_zap.mbn";
+};
+
+&gpu_opp_table {
+	opp-719000000 {
+		opp-hz = /bits/ 64 <719000000>;
+		opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
+		opp-peak-kBps = <10687500>; // Level 7
+		qcom,opp-acd-level = <0x882e5ffd>;
+	};
+
+	opp-746000000 {
+		opp-hz = /bits/ 64 <746000000>;
+		opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
+		opp-peak-kBps = <10687500>; // Level 7
+		qcom,opp-acd-level = <0x882e5ffd>;
+	};
+
+	opp-794000000 {
+		opp-hz = /bits/ 64 <794000000>;
+		opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
+		opp-peak-kBps = <14398438>; // Level 8
+		qcom,opp-acd-level = <0xa82d5ffd>;
+	};
+
+	opp-827000000 {
+		opp-hz = /bits/ 64 <827000000>;
+		opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
+		opp-peak-kBps = <16500000>; // Level 9
+		qcom,opp-acd-level = <0xa82d5ffd>;
+	};
+
+	opp-860000000 {
+		opp-hz = /bits/ 64 <860000000>;
+		opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
+		opp-peak-kBps = <16500000>; // Level 9
+		qcom,opp-acd-level = <0x882d5ffd>;
+	};
+
+	opp-1000000000 {
+		opp-hz = /bits/ 64 <1000000000>;
+		opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L2>;
+		opp-peak-kBps = <16500000>; // Level 9
+		qcom,opp-acd-level = <0x882d5ffd>;
+	};
+};
+
+&i2c_master_hub_0 {
+	status = "okay";
+};
+
+&i2c_hub_2 {
+	status = "okay";
+
+	typec-retimer@1c {
+		compatible = "onnn,nb7vpq904m";
+		reg = <0x1c>;
+		vcc-supply = <&vreg_l15b_1p8>;
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				redriver_ss_out: endpoint {
+					remote-endpoint = <&pmic_glink_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				redriver_ss_in: endpoint {
+					data-lanes = <3 2 1 0>;
+					remote-endpoint = <&usb_dp_qmpphy_out>;
+				};
+			};
+		};
+	};
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+
+	display_panel: panel@0 {
+		reg = <0>;
+
+		pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>;
+		pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>;
+		pinctrl-names = "default", "sleep";
+	};
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l1e_0p88>;
+
+	status = "okay";
+};
+
+&pcie0 {
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+	max-link-speed = <3>;
+
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie1 {
+	wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie1_default_state>;
+	pinctrl-names = "default";
+
+	status = "okay";
+
+	pcie@0 {
+		/* Renesas μPD720201 PCIe USB3.0 HOST CONTROLLER */
+		usb-controller@0 {
+			compatible = "pci1912,0014";
+			reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+			avdd33-supply = <&upd720201_avdd33_reg>;
+			vdd10-supply = <&upd720201_vdd10_reg>;
+			vdd33-supply = <&upd720201_vdd33_reg>;
+
+			pinctrl-0 = <&gamepad_pwr_en>;
+			pinctrl-names = "default";
+		};
+	};
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l3c_0p9>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	vdda-qref-supply = <&vreg_l1e_0p88>;
+
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l17b_2p5>;
+	vcc-max-microamp = <1300000>;
+	vccq-supply = <&vreg_l1g_1p2>;
+	vccq-max-microamp = <1200000>;
+	vdd-hba-supply = <&vreg_l3g_1p2>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l1d_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_hsphy {
+	vdd-supply = <&vreg_l1e_0p88>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&pm8550b_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3f_0p88>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy_out {
+	remote-endpoint = <&redriver_ss_in>;
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+
+		max-speed = <3200000>;
+	};
+};
+
+&iris {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	tca6408: gpio@20 {
+		compatible = "ti,tca6408";
+		reg = <0x20>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		vcc-supply = <&tca6424_vcc>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchscreen@5d {
+		reg = <0x5d>;
+		compatible = "goodix,gt911";
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>;
+		irq-gpios = <&tlmm 39 GPIO_ACTIVE_HIGH>;
+		VDDIO-supply = <&vdd_ts>;
+
+		touchscreen-size-x = <768>;
+		touchscreen-size-y = <1024>;
+
+		pinctrl-0 = <&ts2_reset>, <&ts2_irq>;
+		pinctrl-names = "default";
+	};
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchscreen: touchscreen@38 {
+		compatible = "focaltech,ft5426";
+		reg = <0x38>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+
+		reset-gpios = <&tlmm 24 GPIO_ACTIVE_LOW>;
+
+		vcc-supply = <&vreg_l14b_3p2>;
+		iovcc-supply = <&vreg_l12b_1p8>;
+
+		pinctrl-0 = <&ts_int_default &ts_rst_default>;
+		pinctrl-1 = <&ts_int_sleep &ts_rst_sleep>;
+		pinctrl-names = "default", "sleep";
+
+		touchscreen-size-x = <1080>;
+		touchscreen-size-y = <1920>;
+	};
+};

-- 
2.54.0



^ permalink raw reply related	[flat|nested] 10+ messages in thread

* Re: [PATCH v2 3/3] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console
  2026-05-11 11:33 ` [PATCH v2 3/3] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
@ 2026-05-14 12:25   ` Krzysztof Kozlowski
       [not found]     ` <CAL5cOWtz5VZXGJBRVKNTwbXGciAom8PZ84cZFr2KveW7jO1O=A@mail.gmail.com>
  0 siblings, 1 reply; 10+ messages in thread
From: Krzysztof Kozlowski @ 2026-05-14 12:25 UTC (permalink / raw)
  To: Alexandre Hamamdjian
  Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley, linux-arm-msm, devicetree, linux-kernel,
	Teguh Sobirin

On Mon, May 11, 2026 at 06:33:55PM +0700, Alexandre Hamamdjian wrote:
> +	vdd_ts: vdd-ts {

? So this is not a regulator?

> +		compatible = "regulator-fixed";
> +		regulator-name = "vdd_ts_en";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&tca6408 1 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};

Missing blank line

...

> +	vdd_fan_5v0: vdd-fan-5v0-regulator {

But this is a regulator?

> +		compatible = "regulator-fixed";
> +		regulator-name = "vdd_fan_5v0";
> +
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +
> +		gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-0 = <&fan_pwr_active>;
> +		pinctrl-names = "default";
> +
> +		regulator-state-mem {
> +			regulator-off-in-suspend;
> +		};
> +	};
> +
> +	vph_pwr: regulator-vph-pwr {

So here "regulator-foo"

> +		compatible = "regulator-fixed";
> +		regulator-name = "vph_pwr";
> +		regulator-min-microvolt = <3700000>;
> +		regulator-max-microvolt = <3700000>;
> +
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	upd720201_avdd33_reg: upd720201-avdd33-regulator {

but here "foo-regulator"? Why do you have completely random naming
scheme?

> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "upd720201_avdd33";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		vin-supply = <&vph_pwr>;
> +
> +		pinctrl-0 = <&upd720201_avdd33>;
> +		pinctrl-names = "default";
> +	};
> +
> +	upd720201_vdd10_reg: upd720201-vdd10-regulator {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "upd720201_vdd10";
> +		regulator-min-microvolt = <1050000>;
> +		regulator-max-microvolt = <1050000>;
> +
> +		gpios = <&tlmm 13 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		vin-supply = <&vph_pwr>;
> +
> +		pinctrl-0 = <&upd720201_vdd10>;
> +		pinctrl-names = "default";
> +	};
> +
> +	upd720201_vdd33_reg: upd720201-vdd33-regulator {
> +		compatible = "regulator-fixed";
> +
> +		regulator-name = "upd720201_vdd33";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		vin-supply = <&vph_pwr>;
> +
> +		pinctrl-0 = <&upd720201_vdd33>;
> +		pinctrl-names = "default";
> +	};
> +
> +	pwm_fan: pwm-fan {
> +		compatible = "pwm-fan";
> +
> +		pinctrl-0 = <&fan_pwm_active>, <&fan_int>;
> +		pinctrl-names = "default", "sleep";
> +
> +		fan-supply = <&vdd_fan_5v0>;
> +		pwms = <&pm8550_pwm 3 40000>;
> +		interrupt-parent = <&tlmm>;
> +		interrupts = <64 IRQ_TYPE_EDGE_FALLING>;
> +
> +		#cooling-cells = <2>;
> +		cooling-levels = <0 30 45 60 70 90 120 150>;
> +	};
> +
> +	wcn7850-pmu {
> +		compatible = "qcom,wcn7850-pmu";
> +
> +		pinctrl-0 = <&wlan_en>, <&bt_default>, <&pmk8550_sleep_clk>;
> +		pinctrl-names = "default";
> +
> +		wlan-enable-gpios = <&tlmm 80 GPIO_ACTIVE_HIGH>;
> +		bt-enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
> +
> +		vdd-supply = <&vreg_s5g_0p85>;
> +		vddio-supply = <&vreg_l15b_1p8>;
> +		vddaon-supply = <&vreg_s2g_0p85>;
> +		vdddig-supply = <&vreg_s4e_0p95>;
> +		vddrfa1p2-supply = <&vreg_s4g_1p25>;
> +		vddrfa1p8-supply = <&vreg_s6g_1p86>;
> +
> +		regulators {
> +			vreg_pmu_rfa_cmn: ldo0 {
> +				regulator-name = "vreg_pmu_rfa_cmn";
> +			};
> +
> +			vreg_pmu_aon_0p59: ldo1 {
> +				regulator-name = "vreg_pmu_aon_0p59";
> +			};
> +
> +			vreg_pmu_wlcx_0p8: ldo2 {
> +				regulator-name = "vreg_pmu_wlcx_0p8";
> +			};
> +
> +			vreg_pmu_wlmx_0p85: ldo3 {
> +				regulator-name = "vreg_pmu_wlmx_0p85";
> +			};
> +
> +			vreg_pmu_btcmx_0p85: ldo4 {
> +				regulator-name = "vreg_pmu_btcmx_0p85";
> +			};
> +
> +			vreg_pmu_rfa_0p8: ldo5 {
> +				regulator-name = "vreg_pmu_rfa_0p8";
> +			};
> +
> +			vreg_pmu_rfa_1p2: ldo6 {
> +				regulator-name = "vreg_pmu_rfa_1p2";
> +			};
> +
> +			vreg_pmu_rfa_1p8: ldo7 {
> +				regulator-name = "vreg_pmu_rfa_1p8";
> +			};
> +
> +			vreg_pmu_pcie_0p9: ldo8 {
> +				regulator-name = "vreg_pmu_pcie_0p9";
> +			};
> +
> +			vreg_pmu_pcie_1p8: ldo9 {
> +				regulator-name = "vreg_pmu_pcie_1p8";
> +			};
> +		};
> +	};
> +};
> +
> +&cpuss0_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		cpuss0_fan0: trip-point2 {
> +			temperature = <40000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss0_fan1: trip-point3 {
> +			temperature = <50000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss0_fan2: trip-point4 {
> +			temperature = <60000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss0_fan3: trip-point5 {
> +			temperature = <65000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss0_fan4: trip-point6 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss0_fan5: trip-point7 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss0_fan6: trip-point8 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&cpuss1_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		cpuss1_fan0: trip-point2 {
> +			temperature = <40000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss1_fan1: trip-point3 {
> +			temperature = <50000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss1_fan2: trip-point4 {
> +			temperature = <60000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss1_fan3: trip-point5 {
> +			temperature = <65000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss1_fan4: trip-point6 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss1_fan5: trip-point7 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss1_fan6: trip-point8 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&cpuss2_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		cpuss2_fan0: trip-point2 {
> +			temperature = <40000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss2_fan1: trip-point3 {
> +			temperature = <50000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss2_fan2: trip-point4 {
> +			temperature = <60000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss2_fan3: trip-point5 {
> +			temperature = <65000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss2_fan4: trip-point6 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss2_fan5: trip-point7 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss2_fan6: trip-point8 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&cpuss3_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		cpuss3_fan0: trip-point2 {
> +			temperature = <40000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss3_fan1: trip-point3 {
> +			temperature = <50000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss3_fan2: trip-point4 {
> +			temperature = <60000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss3_fan3: trip-point5 {
> +			temperature = <65000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss3_fan4: trip-point6 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss3_fan5: trip-point7 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpuss3_fan6: trip-point8 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&cpu7_top_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		cpu7_top_fan0: trip-point2 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpu7_top_fan1: trip-point3 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		cpu7_top_fan2: trip-point4 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&gpuss0_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		gpuss0_fan0: trip-point3 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss0_fan1: trip-point4 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss0_fan2: trip-point5 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&gpuss1_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		gpuss1_fan0: trip-point3 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss1_fan1: trip-point4 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss1_fan2: trip-point5 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&gpuss2_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		gpuss2_fan0: trip-point3 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss2_fan1: trip-point4 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss2_fan2: trip-point5 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&gpuss3_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		gpuss3_fan0: trip-point3 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss3_fan1: trip-point4 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss3_fan2: trip-point5 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&gpuss4_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		gpuss4_fan0: trip-point3 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss4_fan1: trip-point4 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss4_fan2: trip-point5 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&gpuss5_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		gpuss5_fan0: trip-point3 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss5_fan1: trip-point4 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss5_fan2: trip-point5 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&gpuss6_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		gpuss6_fan0: trip-point3 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss6_fan1: trip-point4 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss6_fan2: trip-point5 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +&gpuss7_thermal {
> +	polling-delay = <200>;
> +
> +	trips {
> +		gpuss7_fan0: trip-point3 {
> +			temperature = <70000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss7_fan1: trip-point4 {
> +			temperature = <75000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +
> +		gpuss7_fan2: trip-point5 {
> +			temperature = <80000>;
> +			hysteresis = <3000>;
> +			type = "passive";
> +		};
> +	};
> +};
> +
> +/* DMIC 01 23 */
> +&lpass_vamacro {
> +	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
> +	pinctrl-names = "default";
> +	vdd-micb-supply = <&vreg_l10b_1p8>;
> +	qcom,dmic-sample-rate = <4800000>;
> +};
> +
> +&apps_rsc {
> +	regulators-0 {
> +		compatible = "qcom,pm8550-rpmh-regulators";
> +		qcom,pmic-id = "b";
> +
> +		vdd-bob1-supply = <&vph_pwr>;
> +		vdd-bob2-supply = <&vph_pwr>;
> +		vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>;
> +		vdd-l2-l13-l14-supply = <&vreg_bob1>;
> +		vdd-l3-supply = <&vreg_s4g_1p25>;
> +		vdd-l5-l16-supply = <&vreg_bob1>;
> +		vdd-l6-l7-supply = <&vreg_bob1>;
> +		vdd-l8-l9-supply = <&vreg_bob1>;
> +		vdd-l11-supply = <&vreg_s4g_1p25>;
> +		vdd-l12-supply = <&vreg_s6g_1p86>;
> +		vdd-l15-supply = <&vreg_s6g_1p86>;
> +		vdd-l17-supply = <&vreg_bob2>;
> +
> +		vreg_bob1: bob1 {
> +			regulator-name = "vreg_bob1";
> +			regulator-min-microvolt = <3296000>;
> +			regulator-max-microvolt = <3960000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_bob2: bob2 {
> +			regulator-name = "vreg_bob2";
> +			regulator-min-microvolt = <2720000>;
> +			regulator-max-microvolt = <3960000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l2b_3p0: ldo2 {
> +			regulator-name = "vreg_l2b_3p0";
> +			regulator-min-microvolt = <3008000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l5b_3p1: ldo5 {
> +			regulator-name = "vreg_l5b_3p1";
> +			regulator-min-microvolt = <3104000>;
> +			regulator-max-microvolt = <3104000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l6b_1p8: ldo6 {
> +			regulator-name = "vreg_l6b_1p8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l7b_1p8: ldo7 {
> +			regulator-name = "vreg_l7b_1p8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l8b_1p8: ldo8 {
> +			regulator-name = "vreg_l8b_1p8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l9b_2p9: ldo9 {
> +			regulator-name = "vreg_l9b_2p9";
> +			regulator-min-microvolt = <2960000>;
> +			regulator-max-microvolt = <3008000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l10b_1p8: ldo10 {
> +			regulator-name = "vreg_l10b_1p8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l11b_1p2: ldo11 {
> +			regulator-name = "vreg_l11b_1p2";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1504000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l12b_1p8: ldo12 {
> +			regulator-name = "vreg_l12b_1p8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l13b_3p0: ldo13 {
> +			regulator-name = "vreg_l13b_3p0";
> +			regulator-min-microvolt = <3000000>;
> +			regulator-max-microvolt = <3000000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l14b_3p2: ldo14 {
> +			regulator-name = "vreg_l14b_3p2";
> +			regulator-min-microvolt = <3200000>;
> +			regulator-max-microvolt = <3200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l15b_1p8: ldo15 {
> +			regulator-name = "vreg_l15b_1p8";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l16b_2p8: ldo16 {
> +			regulator-name = "vreg_l16b_2p8";
> +			regulator-min-microvolt = <2800000>;
> +			regulator-max-microvolt = <2800000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l17b_2p5: ldo17 {
> +			regulator-name = "vreg_l17b_2p5";
> +			regulator-min-microvolt = <2504000>;
> +			regulator-max-microvolt = <2504000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-1 {
> +		compatible = "qcom,pm8550vs-rpmh-regulators";
> +		qcom,pmic-id = "c";
> +
> +		vdd-l1-supply = <&vreg_s4g_1p25>;
> +		vdd-l2-supply = <&vreg_s4e_0p95>;
> +		vdd-l3-supply = <&vreg_s4e_0p95>;
> +
> +		vreg_l3c_0p9: ldo3 {
> +			regulator-name = "vreg_l3c_0p9";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-2 {
> +		compatible = "qcom,pm8550vs-rpmh-regulators";
> +		qcom,pmic-id = "d";
> +
> +		vdd-l1-supply = <&vreg_s4e_0p95>;
> +		vdd-l2-supply = <&vreg_s4e_0p95>;
> +		vdd-l3-supply = <&vreg_s4e_0p95>;
> +
> +		vreg_l1d_0p88: ldo1 {
> +			regulator-name = "vreg_l1d_0p88";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <920000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-3 {
> +		compatible = "qcom,pm8550vs-rpmh-regulators";
> +		qcom,pmic-id = "e";
> +
> +		vdd-l1-supply = <&vreg_s4e_0p95>;
> +		vdd-l2-supply = <&vreg_s4e_0p95>;
> +		vdd-l3-supply = <&vreg_s4g_1p25>;
> +		vdd-s4-supply = <&vph_pwr>;
> +		vdd-s5-supply = <&vph_pwr>;
> +
> +		vreg_s4e_0p95: smps4 {
> +			regulator-name = "vreg_s4e_0p95";
> +			regulator-min-microvolt = <904000>;
> +			regulator-max-microvolt = <984000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s5e_1p08: smps5 {
> +			regulator-name = "vreg_s5e_1p08";
> +			regulator-min-microvolt = <1010000>;
> +			regulator-max-microvolt = <1120000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l1e_0p88: ldo1 {
> +			regulator-name = "vreg_l1e_0p88";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <880000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l2e_0p9: ldo2 {
> +			regulator-name = "vreg_l2e_0p9";
> +			regulator-min-microvolt = <904000>;
> +			regulator-max-microvolt = <970000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l3e_1p2: ldo3 {
> +			regulator-name = "vreg_l3e_1p2";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-4 {
> +		compatible = "qcom,pm8550ve-rpmh-regulators";
> +		qcom,pmic-id = "f";
> +
> +		vdd-l1-supply = <&vreg_s4e_0p95>;
> +		vdd-l2-supply = <&vreg_s4e_0p95>;
> +		vdd-l3-supply = <&vreg_s4e_0p95>;
> +		vdd-s4-supply = <&vph_pwr>;
> +
> +		vreg_s4f_0p5: smps4 {
> +			regulator-name = "vreg_s4f_0p5";
> +			regulator-min-microvolt = <500000>;
> +			regulator-max-microvolt = <700000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l1f_0p9: ldo1 {
> +			regulator-name = "vreg_l1f_0p9";
> +			regulator-min-microvolt = <912000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l2f_0p88: ldo2 {
> +			regulator-name = "vreg_l2f_0p88";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l3f_0p88: ldo3 {
> +			regulator-name = "vreg_l3f_0p88";
> +			regulator-min-microvolt = <880000>;
> +			regulator-max-microvolt = <912000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +
> +	regulators-5 {
> +		compatible = "qcom,pm8550vs-rpmh-regulators";
> +		qcom,pmic-id = "g";
> +		vdd-l1-supply = <&vreg_s4g_1p25>;
> +		vdd-l2-supply = <&vreg_s4g_1p25>;
> +		vdd-l3-supply = <&vreg_s4g_1p25>;
> +		vdd-s1-supply = <&vph_pwr>;
> +		vdd-s2-supply = <&vph_pwr>;
> +		vdd-s3-supply = <&vph_pwr>;
> +		vdd-s4-supply = <&vph_pwr>;
> +		vdd-s5-supply = <&vph_pwr>;
> +		vdd-s6-supply = <&vph_pwr>;
> +
> +		vreg_s1g_1p25: smps1 {
> +			regulator-name = "vreg_s1g_1p25";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1300000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s2g_0p85: smps2 {
> +			regulator-name = "vreg_s2g_0p85";
> +			regulator-min-microvolt = <800000>;
> +			regulator-max-microvolt = <1000000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s3g_0p8: smps3 {
> +			regulator-name = "vreg_s3g_0p8";
> +			regulator-min-microvolt = <300000>;
> +			regulator-max-microvolt = <1004000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s4g_1p25: smps4 {
> +			regulator-name = "vreg_s4g_1p25";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1352000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s5g_0p85: smps5 {
> +			regulator-name = "vreg_s5g_0p85";
> +			regulator-min-microvolt = <500000>;
> +			regulator-max-microvolt = <1004000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_s6g_1p86: smps6 {
> +			regulator-name = "vreg_s6g_1p86";
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <2000000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l1g_1p2: ldo1 {
> +			regulator-name = "vreg_l1g_1p2";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +
> +		vreg_l3g_1p2: ldo3 {
> +			regulator-name = "vreg_l3g_1p2";
> +			regulator-min-microvolt = <1200000>;
> +			regulator-max-microvolt = <1200000>;
> +			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> +			regulator-allow-set-load;
> +			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> +						   RPMH_REGULATOR_MODE_HPM>;
> +		};
> +	};
> +};
> +
> +&pm8550_gpios {
> +	sdc2_card_det_n: sdc2-card-det-n-state {
> +		pins = "gpio12";
> +		function = "normal";
> +		input-enable;
> +		output-disable;
> +		bias-pull-up;
> +		power-source = <1>;
> +	};
> +
> +	volume_up_n: volume-up-n-state {
> +		pins = "gpio6";
> +		function = "normal";
> +		power-source = <1>;
> +		bias-pull-up;
> +		input-enable;
> +	};
> +
> +	fan_pwm_active: fan-pwm-active-state {
> +		pins = "gpio9";
> +		function = "func1";
> +		output-low;
> +		bias-disable;
> +		power-source = <0>;
> +		qcom,drive-strength = <3>; /* PMIC_GPIO_STRENGTH_LOW */
> +	};
> +};
> +
> +&pmk8550_gpios {
> +	pmk8550_sleep_clk: sleep-clk-state {
> +		pins = "gpio3";
> +		function = "func1";
> +		input-disable;
> +		output-enable;
> +		bias-disable;
> +		power-source = <0>;
> +	};
> +};
> +
> +&pm8550b_eusb2_repeater {
> +	vdd18-supply = <&vreg_l15b_1p8>;
> +	vdd3-supply = <&vreg_l5b_3p1>;
> +};
> +
> +&pon_pwrkey {
> +	status = "okay";
> +};
> +
> +&pon_resin {
> +	linux,code = <KEY_VOLUMEDOWN>;
> +
> +	status = "okay";
> +};
> +
> +&pmk8550_rtc {
> +	nvmem-cells = <&rtc_offset>;
> +	nvmem-cell-names = "offset";
> +};
> +
> +&pmk8550_sdam_2 {
> +	rtc_offset: rtc-offset@bc {
> +		reg = <0xbc 0x4>;
> +	};
> +};
> +
> +&qupv3_id_0 {
> +	status = "okay";
> +};
> +
> +&qupv3_id_1 {
> +	status = "okay";
> +
> +	/* AYANEO Controller serial interface */
> +	uart11: serial@88c000 {

Why isn't this part of the SoC?

> +		compatible = "qcom,geni-uart";
> +		reg = <0 0x0088c000 0 0x4000>;

DTS should not define SoC components. How do you exactly see that
happening during assembly of SoC on the board?

> +		clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
> +		clock-names = "se";
> +		pinctrl-0 = <&qup_uart11_default>;
> +		pinctrl-names = "default";
> +		interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH 0>;
> +		interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
> +				 &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
> +				<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
> +				 &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ACTIVE_ONLY>;
> +		interconnect-names = "qup-core", "qup-config";
> +		operating-points-v2 = <&qup_opp_table_100mhz>;
> +		power-domains = <&rpmhpd RPMHPD_CX>;
> +
> +		status = "okay";
> +	};
> +};
> +
> +&remoteproc_adsp {
> +	firmware-name = "qcom/sm8550/ayaneo/adsp.mdt",
> +			"qcom/sm8550/ayaneo/adsp_dtb.mdt";
> +
> +	status = "okay";
> +};
> +
> +&sdhc_2 {
> +	cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
> +	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
> +	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
> +	pinctrl-names = "default", "sleep";
> +	vmmc-supply = <&vreg_l9b_2p9>;
> +	vqmmc-supply = <&vreg_l8b_1p8>;
> +	no-sdio;
> +	no-mmc;
> +
> +	sd-uhs-sdr12;
> +	sd-uhs-sdr25;
> +	sd-uhs-sdr50;
> +	sd-uhs-sdr104;
> +	sd-uhs-ddr50;
> +
> +	qcom,dll-config = <0x0007442c>;
> +	sdhci-caps-mask = <0x3 0x0>;
> +
> +	status = "okay";
> +};
> +
> +&sleep_clk {
> +	clock-frequency = <32764>;
> +};
> +
> +&swr0 {
> +	status = "okay";
> +
> +	spk_amp_l: speaker@0,0 {
> +		compatible = "sdw20217020400";
> +		reg = <0 0>;
> +
> +		pinctrl-0 = <&spkr_1_sd_n_active>;
> +		pinctrl-names = "default";
> +
> +		powerdown-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
> +
> +		vdd-1p8-supply = <&vreg_l10b_1p8>;
> +		vdd-io-supply = <&vreg_l10b_1p8>;
> +
> +		#sound-dai-cells = <0>;
> +		sound-name-prefix = "SpkrLeft";
> +		qcom,port-mapping = <1 2 3 7 10 13>;
> +	};
> +
> +	spk_amp_r: speaker@0,1 {
> +		compatible = "sdw20217020400";
> +		reg = <0 1>;
> +
> +		pinctrl-0 = <&spkr_2_sd_n_active>;
> +		pinctrl-names = "default";
> +
> +		powerdown-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
> +
> +		vdd-1p8-supply = <&vreg_l10b_1p8>;
> +		vdd-io-supply = <&vreg_l10b_1p8>;
> +
> +		#sound-dai-cells = <0>;
> +		sound-name-prefix = "SpkrRight";
> +		qcom,port-mapping = <4 5 6 7 11 13>;
> +	};
> +};
> +
> +&tlmm {
> +	gpio-reserved-ranges = <32 4>;
> +
> +	bt_default: bt-default-state {
> +		bt-en-pins {
> +			pins = "gpio81";
> +			function = "gpio";
> +			drive-strength = <16>;
> +			bias-disable;
> +		};
> +
> +		sw-ctrl-pins {
> +			pins = "gpio82";
> +			function = "gpio";
> +			bias-pull-down;
> +		};
> +	};
> +
> +	fan_pwr_active: fan-pwr-active-state {
> +		pins = "gpio31";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +		output-low;
> +	};
> +
> +	fan_int: fan-int-state {
> +		pins = "gpio64";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-up;
> +	};
> +
> +	upd720201_avdd33: upd720201-avdd33-state {
> +		pins = "gpio10";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	upd720201_vdd10: upd720201-vdd10-state {
> +		pins = "gpio13";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	upd720201_vdd33: upd720201-vdd33-state {
> +		pins = "gpio18";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	gamepad_pwr_en: gamepad-pwr-en-active-state {
> +		pins = "gpio52";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +		output-high;
> +	};
> +
> +	qup_uart11_default: qup-uart11-default-state {
> +		/* TX, RX */
> +		pins = "gpio70", "gpio71";
> +		function = "qup2_se3";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
> +	sde_dsi_active: sde-dsi-active-state {
> +		pins = "gpio133";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-disable;
> +		output-high;
> +	};
> +
> +	sde_dsi_suspend: sde-dsi-suspend-state {
> +		pins = "gpio133";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	sde_te_active: sde-te-active-state {
> +		pins = "gpio86";
> +		function = "mdp_vsync";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	sde_te_suspend: sde-te-suspend-state {
> +		pins = "gpio86";
> +		function = "mdp_vsync";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	wlan_en: wlan-en-state {
> +		pins = "gpio80";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-pull-down;
> +	};
> +
> +	spkr_1_sd_n_active: spkr-1-sd-n-active-state {
> +		pins = "gpio7";
> +		function = "gpio";
> +		drive-strength = <16>;
> +		bias-disable;
> +		output-high;
> +	};
> +
> +	spkr_2_sd_n_active: spkr-2-sd-n-active-state {
> +		pins = "gpio12";
> +		function = "gpio";
> +		drive-strength = <16>;
> +		bias-disable;
> +		output-high;
> +	};
> +
> +	panel_pwr_active: panel-pwr-active-state {
> +		pins = "gpio152", "gpio153";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-disable;
> +		output-high;
> +	};
> +
> +	sde_dsi1_active: sde-dsi1-active-state {
> +		pins = "gpio137";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-disable;
> +		output-high;
> +	};
> +
> +	sde_dsi1_suspend: sde-dsi1-suspend-state {
> +		pins = "gpio137";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-pull-down;
> +	};
> +
> +	ts_rst_default: ts-rst-default-state {
> +		pins = "gpio24";
> +		function = "gpio";
> +		bias-pull-up;
> +		drive-strength = <8>;
> +	};
> +
> +	ts_rst_sleep: ts-rst-sleep-state {
> +		pins = "gpio24";
> +		function = "gpio";
> +		bias-pull-down;
> +		drive-strength = <2>;
> +	};
> +
> +	ts_int_default: ts-int-default-state {
> +		pins = "gpio25";
> +		function = "gpio";
> +		bias-pull-up;
> +		drive-strength = <8>;
> +	};
> +
> +	ts_int_sleep: ts-int-sleep-state {
> +		pins = "gpio25";
> +		function = "gpio";
> +		bias-pull-down;
> +		drive-strength = <2>;
> +	};
> +
> +	ts2_irq: ts2-irq-state {
> +		pins = "gpio39";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-disable;
> +	};
> +
> +	ts2_reset: ts2-reset-state {
> +		pins = "gpio38";
> +		function = "gpio";
> +		drive-strength = <8>;
> +		bias-pull-down;
> +	};
> +};
> +
> +&pm8550_pwm {
> +	status = "okay";
> +};
> +
> +&xo_board {
> +	clock-frequency = <76800000>;
> +};
> +
> +&gpi_dma1 {
> +	status = "okay";
> +};
> +
> +&gpi_dma2 {
> +	status = "okay";
> +};
> +
> +&gpu {
> +	status = "okay";
> +};
> +
> +&gpu_zap_shader {
> +	firmware-name = "qcom/sm8550/a740_zap.mbn";
> +};
> +
> +&gpu_opp_table {
> +	opp-719000000 {
> +		opp-hz = /bits/ 64 <719000000>;
> +		opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
> +		opp-peak-kBps = <10687500>; // Level 7
> +		qcom,opp-acd-level = <0x882e5ffd>;
> +	};
> +
> +	opp-746000000 {
> +		opp-hz = /bits/ 64 <746000000>;
> +		opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
> +		opp-peak-kBps = <10687500>; // Level 7
> +		qcom,opp-acd-level = <0x882e5ffd>;
> +	};
> +
> +	opp-794000000 {
> +		opp-hz = /bits/ 64 <794000000>;
> +		opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
> +		opp-peak-kBps = <14398438>; // Level 8
> +		qcom,opp-acd-level = <0xa82d5ffd>;
> +	};
> +
> +	opp-827000000 {
> +		opp-hz = /bits/ 64 <827000000>;
> +		opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
> +		opp-peak-kBps = <16500000>; // Level 9
> +		qcom,opp-acd-level = <0xa82d5ffd>;
> +	};
> +
> +	opp-860000000 {
> +		opp-hz = /bits/ 64 <860000000>;
> +		opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
> +		opp-peak-kBps = <16500000>; // Level 9
> +		qcom,opp-acd-level = <0x882d5ffd>;
> +	};
> +
> +	opp-1000000000 {
> +		opp-hz = /bits/ 64 <1000000000>;
> +		opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L2>;
> +		opp-peak-kBps = <16500000>; // Level 9
> +		qcom,opp-acd-level = <0x882d5ffd>;
> +	};
> +};
> +
> +&i2c_master_hub_0 {
> +	status = "okay";
> +};
> +
> +&i2c_hub_2 {
> +	status = "okay";
> +
> +	typec-retimer@1c {
> +		compatible = "onnn,nb7vpq904m";
> +		reg = <0x1c>;
> +		vcc-supply = <&vreg_l15b_1p8>;
> +
> +		retimer-switch;
> +		orientation-switch;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +
> +				redriver_ss_out: endpoint {
> +					remote-endpoint = <&pmic_glink_ss_in>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +
> +				redriver_ss_in: endpoint {
> +					data-lanes = <3 2 1 0>;
> +					remote-endpoint = <&usb_dp_qmpphy_out>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&mdss {
> +	status = "okay";
> +};
> +
> +&mdss_dp0 {
> +	status = "okay";
> +};
> +
> +&mdss_dp0_out {
> +	data-lanes = <0 1 2 3>;
> +};
> +
> +&mdss_dsi0 {
> +	vdda-supply = <&vreg_l3e_1p2>;
> +
> +	status = "okay";
> +
> +	display_panel: panel@0 {
> +		reg = <0>;
> +
> +		pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>;
> +		pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>;
> +		pinctrl-names = "default", "sleep";
> +	};
> +};
> +
> +&mdss_dsi0_phy {
> +	vdds-supply = <&vreg_l1e_0p88>;
> +
> +	status = "okay";
> +};
> +
> +&pcie0 {
> +	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
> +	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
> +
> +	max-link-speed = <3>;
> +
> +	pinctrl-0 = <&pcie0_default_state>;
> +	pinctrl-names = "default";
> +
> +	status = "okay";
> +};
> +
> +&pcie1 {
> +	wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
> +	perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
> +
> +	pinctrl-0 = <&pcie1_default_state>;
> +	pinctrl-names = "default";
> +
> +	status = "okay";
> +
> +	pcie@0 {
> +		/* Renesas μPD720201 PCIe USB3.0 HOST CONTROLLER */
> +		usb-controller@0 {
> +			compatible = "pci1912,0014";
> +			reg = <0x10000 0x0 0x0 0x0 0x0>;
> +
> +			avdd33-supply = <&upd720201_avdd33_reg>;
> +			vdd10-supply = <&upd720201_vdd10_reg>;
> +			vdd33-supply = <&upd720201_vdd33_reg>;
> +
> +			pinctrl-0 = <&gamepad_pwr_en>;
> +			pinctrl-names = "default";
> +		};
> +	};
> +};
> +
> +&pcie1_phy {
> +	vdda-phy-supply = <&vreg_l3c_0p9>;
> +	vdda-pll-supply = <&vreg_l3e_1p2>;
> +	vdda-qref-supply = <&vreg_l1e_0p88>;
> +
> +	status = "okay";
> +};
> +
> +&ufs_mem_hc {
> +	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
> +
> +	vcc-supply = <&vreg_l17b_2p5>;
> +	vcc-max-microamp = <1300000>;
> +	vccq-supply = <&vreg_l1g_1p2>;
> +	vccq-max-microamp = <1200000>;
> +	vdd-hba-supply = <&vreg_l3g_1p2>;
> +
> +	status = "okay";
> +};
> +
> +&ufs_mem_phy {
> +	vdda-phy-supply = <&vreg_l1d_0p88>;
> +	vdda-pll-supply = <&vreg_l3e_1p2>;
> +
> +	status = "okay";
> +};
> +
> +&usb_1 {
> +	status = "okay";
> +};
> +
> +&usb_1_dwc3_hs {
> +	remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_hsphy {
> +	vdd-supply = <&vreg_l1e_0p88>;
> +	vdda12-supply = <&vreg_l3e_1p2>;
> +
> +	phys = <&pm8550b_eusb2_repeater>;
> +
> +	status = "okay";
> +};
> +
> +&usb_dp_qmpphy {
> +	vdda-phy-supply = <&vreg_l3e_1p2>;
> +	vdda-pll-supply = <&vreg_l3f_0p88>;
> +
> +	status = "okay";
> +};
> +
> +&usb_dp_qmpphy_out {
> +	remote-endpoint = <&redriver_ss_in>;
> +};
> +
> +&uart7 {
> +	status = "okay";
> +};
> +
> +&uart14 {
> +	status = "okay";
> +
> +	bluetooth {
> +		compatible = "qcom,wcn7850-bt";
> +
> +		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
> +		vddaon-supply = <&vreg_pmu_aon_0p59>;
> +		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> +		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
> +		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
> +		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
> +		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
> +
> +		max-speed = <3200000>;
> +	};
> +};
> +
> +&iris {

Looks like random ordering...

> +	status = "okay";
> +};
> +

Best regards,
Krzysztof


^ permalink raw reply	[flat|nested] 10+ messages in thread

[parent not found: <CAL5cOWtz5VZXGJBRVKNTwbXGciAom8PZ84cZFr2KveW7jO1O=A@mail.gmail.com>]

[parent not found: <CAL5cOWu20Vng7hMZvyz0paFM6Ga=Fs2qQrF2yfMTpVvSt3b0VA@mail.gmail.com>]

* Re: [PATCH v2 3/3] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console
       [not found]       ` <CAL5cOWu20Vng7hMZvyz0paFM6Ga=Fs2qQrF2yfMTpVvSt3b0VA@mail.gmail.com>
@ 2026-05-14 13:46         ` Krzysztof Kozlowski
  0 siblings, 0 replies; 10+ messages in thread
From: Krzysztof Kozlowski @ 2026-05-14 13:46 UTC (permalink / raw)
  To: Alexandre Hamamdjian
  Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
	Conor Dooley, linux-arm-msm, devicetree, linux-kernel,
	Teguh Sobirin

On 14/05/2026 15:00, Alexandre Hamamdjian wrote:
> I will fix the naming scheme and blank line for the next revision.
> 
>> Why isn't this part of the SoC?
> 
> I was suggested to look at similar devicetree (ayaneo-pocket-s2) which is
> doing the same defining in the exact same way the SoC regulators, labeled
> thermal nodes, pmu etc..
> I am open to staying consistent but would like the same consistency to be
> set or questioned for others the same way.

Really? I could not find regulators starting there with 'regulator-'
name or regulators without any prefix or suffix.

> 
>> Looks like random ordering...
> 
> I can reorder if you have advice or documentation on better ordering

That ayaneo-pocket-s2 has correct order so you could even use that one.
DTS coding style document describes preferred ordering.

Please do not remove pieces of the context - I have no clue what my
replies were referring to. I have this in the inbox without the rest, so
judging by inbox alone I do not know what this is even replied to,
unless I perform some actions.

Your way of handling emails is really not making it easy. Just use
standard email reply style as on every mailing list.

Best regards,
Krzysztof

^ permalink raw reply	[flat|nested] 10+ messages in thread

end of thread, other threads:[~2026-05-14 13:46 UTC | newest]

Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-05-11 11:33 [PATCH v2 0/3] arm64: qcom: add Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
2026-05-11 11:33 ` [PATCH v2 1/3] dt-bindings: arm: qcom: document the Ayaneo Pocket DS Alexandre Hamamdjian via B4 Relay
2026-05-14 12:20   ` Krzysztof Kozlowski
     [not found]     ` <CAL5cOWtRUs-XF5Y6+X-G3PVkGQp-ts+HTiAfzezVjQqYoyt1NQ@mail.gmail.com>
2026-05-14 12:31       ` Krzysztof Kozlowski
2026-05-11 11:33 ` [PATCH v2 2/3] arm64: dts: qcom: sm8550: add labels for thermal zones Alexandre Hamamdjian via B4 Relay
2026-05-11 12:55   ` Neil Armstrong
2026-05-14 12:26   ` Krzysztof Kozlowski
2026-05-11 11:33 ` [PATCH v2 3/3] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
2026-05-14 12:25   ` Krzysztof Kozlowski
     [not found]     ` <CAL5cOWtz5VZXGJBRVKNTwbXGciAom8PZ84cZFr2KveW7jO1O=A@mail.gmail.com>
     [not found]       ` <CAL5cOWu20Vng7hMZvyz0paFM6Ga=Fs2qQrF2yfMTpVvSt3b0VA@mail.gmail.com>
2026-05-14 13:46         ` Krzysztof Kozlowski

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox