Re: [PATCH 10/11] arm64: dts: qcom: ipq5018: Add MP03.5-c1 board support

[Manikanta Mylavarapu <quic_mmanikan@quicinc.com>]

On 3/7/2023 9:12 PM, Krzysztof Kozlowski wrote:
> On 07/03/2023 05:41, Manikanta Mylavarapu wrote:
>> Add initial device tree support for the MP03.5-C1 board.
>>
>> Signed-off-by: Manikanta Mylavarapu <quic_mmanikan@quicinc.com>
>> ---
>>   arch/arm64/boot/dts/qcom/Makefile             |  1 +
>>   .../arm64/boot/dts/qcom/ipq5018-mp03.5-c1.dts | 64 +++++++++++++++++++
>>   2 files changed, 65 insertions(+)
>>   create mode 100644 arch/arm64/boot/dts/qcom/ipq5018-mp03.5-c1.dts
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index b77a95e97a56..10d1eafe57e4 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -4,6 +4,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= apq8094-sony-xperia-kitakami-karin_windy.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-db820c.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= apq8096-ifc6640.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= ipq5018-mp03.1-c2.dtb
>> +dtb-$(CONFIG_ARCH_QCOM)	+= ipq5018-mp03.5-c1.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= ipq6018-cp01-c1.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk01.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= ipq8074-hk10-c1.dtb
>> diff --git a/arch/arm64/boot/dts/qcom/ipq5018-mp03.5-c1.dts b/arch/arm64/boot/dts/qcom/ipq5018-mp03.5-c1.dts
>> new file mode 100644
>> index 000000000000..51ddd7367ac6
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/ipq5018-mp03.5-c1.dts
>> @@ -0,0 +1,64 @@
>> +// SPDX-License-Identifier: GPL-2.0+ OR BSD-3-Clause
>> +/*
>> + * IPQ5018 CP01 board device tree source
>> + *
>> + * Copyright (c) 2020-2021, The Linux Foundation. All rights reserved.
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include "ipq5018.dtsi"
>> +
>> +/ {
>> +	model = "Qualcomm Technologies, Inc. IPQ5018/AP-MP03.5-C1";
>> +	compatible = "qcom,ipq5018-mp03.5-c1", "qcom,ipq5018";
>> +
>> +	aliases {
>> +		serial0 = &blsp1_uart1;
>> +	};
>> +
>> +	chosen {
>> +		bootargs = "console=ttyMSM0,115200,n8 rw init=/init swiotlb=1 coherent_pool=2M";
> 
> Not a common DT property. Drop.
> 
Sure, i will drop it.
>> +		stdout-path = "serial0:115200n8";
>> +	};
>> +};
>> +
>> +&tlmm {
>> +	blsp0_uart_pins: uart_pins {
> 
> Does not look like you tested the DTS against bindings. Please run `make
> dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
> for instructions).
> 
> I'll stop the review. Please first run tests.
> 
>
I will verify DTS against bindings.

Thanks & Regards,
Manikanta.

> 
> Best regards,
> Krzysztof
>