Re: [PATCH v6 5/5] arm64: dts: qcom: sdm670-google-sargo: add imx355 front camera

[Bryan O'Donoghue <bod@kernel.org>]

On 07/01/2026 04:30, Richard Acayan wrote:
> The Sony IMX355 is the front camera on the Pixel 3a, mounted in portrait
> mode. It is connected to CSIPHY1 and CCI I2C1, and uses MCLK2. Add
> support for it.
> 
> Co-developed-by: Robert Mader <robert.mader@collabora.com>
> Signed-off-by: Robert Mader <robert.mader@collabora.com>
> Signed-off-by: Richard Acayan <mailingradian@gmail.com>
> ---
>   .../boot/dts/qcom/sdm670-google-sargo.dts     | 104 ++++++++++++++++++
>   1 file changed, 104 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts b/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
> index ed55646ca419..ec447fe3959a 100644
> --- a/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
> +++ b/arch/arm64/boot/dts/qcom/sdm670-google-sargo.dts
> @@ -172,6 +172,34 @@ vreg_s2b_1p05: vreg-s2b-regulator {
>   		regulator-min-microvolt = <1050000>;
>   		regulator-max-microvolt = <1050000>;
>   	};
> +
> +	cam_front_ldo: cam-front-ldo-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "cam_front_ldo";
> +		regulator-min-microvolt = <1352000>;
> +		regulator-max-microvolt = <1352000>;
> +		regulator-enable-ramp-delay = <135>;
> +
> +		gpios = <&pm660l_gpios 4 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-0 = <&cam_front_ldo_pin>;
> +		pinctrl-names = "default";
> +	};
> +
> +	cam_vio_ldo: cam-vio-ldo-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "cam_vio_ldo";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +		regulator-enable-ramp-delay = <233>;
> +
> +		gpios = <&pm660_gpios 13 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +
> +		pinctrl-0 = <&cam_vio_pin>;
> +		pinctrl-names = "default";
> +	};
>   };
> 
>   &apps_rsc {
> @@ -392,6 +420,61 @@ vreg_bob: bob {
>   	};
>   };
> 
> +&camss {
> +	vdda-phy-supply = <&vreg_l1a_1p225>;
> +	vdda-pll-supply = <&vreg_s6a_0p87>;
> +
> +	status = "okay";
> +};
> +
> +&camss_port1 {
> +	camss_endpoint1: endpoint {
> +		clock-lanes = <7>;
> +		data-lanes = <0 1 2 3>;
> +		remote-endpoint = <&cam_front_endpoint>;
> +	};
> +};
> +
> +&cci {
> +	pinctrl-0 = <&cci1_default>;
> +	pinctrl-1 = <&cci1_sleep>;
> +	pinctrl-names = "default", "sleep";
> +
> +	status = "okay";
> +};
> +
> +&cci_i2c1 {
> +	camera@1a {
> +		compatible = "sony,imx355";
> +		reg = <0x1a>;
> +
> +		clocks = <&camcc CAM_CC_MCLK2_CLK>;
> +
> +		assigned-clocks = <&camcc CAM_CC_MCLK2_CLK>;
> +		assigned-clock-rates = <19200000>;
> +
> +		reset-gpios = <&tlmm 9 GPIO_ACTIVE_LOW>;
> +
> +		avdd-supply = <&cam_front_ldo>;
> +		dvdd-supply = <&cam_front_ldo>;
> +		dovdd-supply = <&cam_vio_ldo>;
> +
> +		pinctrl-0 = <&cam_front_default &cam_mclk2_default>;
> +		pinctrl-names = "default";
> +
> +		rotation = <270>;
> +		orientation = <0>;
> +
> +		port {
> +			cam_front_endpoint: endpoint {
> +				data-lanes = <1 2 3 4>;
> +				link-frequencies = /bits/ 64 <360000000>;
> +				remote-endpoint = <&camss_endpoint1>;
> +			};
> +		};
> +	};
> +};
> +
>   &gcc {
>   	protected-clocks = <GCC_QSPI_CORE_CLK>,
>   			   <GCC_QSPI_CORE_CLK_SRC>,
> @@ -490,6 +573,14 @@ &pm660_charger {
>   	status = "okay";
>   };
> 
> +&pm660_gpios {
> +	cam_vio_pin: cam-vio-state {
> +		pins = "gpio13";
> +		function = "normal";
> +		power-source = <0>;
> +	};
> +};
> +
>   &pm660_rradc {
>   	status = "okay";
>   };
> @@ -508,6 +599,12 @@ led-0 {
>   };
> 
>   &pm660l_gpios {
> +	cam_front_ldo_pin: cam-front-state {
> +		pins = "gpio4";
> +		function = "normal";
> +		power-source = <0>;
> +	};
> +
>   	vol_up_pin: vol-up-state {
>   		pins = "gpio7";
>   		function = "normal";
> @@ -547,6 +644,13 @@ &sdhc_1 {
>   &tlmm {
>   	gpio-reserved-ranges = <0 4>, <81 4>;
> 
> +	cam_front_default: cam-front-default-state {
> +		pins = "gpio9";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		bias-disable;
> +	};
> +
>   	panel_default: panel-default-state {
>   		te-pins {
>   			pins = "gpio10";
> --
> 2.52.0
> 
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>