* [PATCH 2/2] arm64: dts: qcom: qcs8300: Add monaco-ac-sku EVK board
2026-03-28 11:41 [PATCH 0/2] arm64: dts: qcom: Introduce support for Monaco-ac-sku Evaluation Kit Umang Chheda
2026-03-28 11:41 ` [PATCH 1/2] dt-bindings: arm: qcom: Add monaco-evk-ac-sku support Umang Chheda
@ 2026-03-28 11:41 ` Umang Chheda
1 sibling, 0 replies; 9+ messages in thread
From: Umang Chheda @ 2026-03-28 11:41 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Richard Cochran
Cc: linux-arm-msm, devicetree, linux-kernel, Umang Chheda,
Faruque Ansari
Add initial device tree support for monaco-ac-sku EVK board,
based on Qualcomm's QCS8300-AC variant SoC.
monaco-ac-sku EVK is single board supporting these peripherals :
- Storage: 1 × 128 GB UFS, micro-SD card, EEPROMs for MACs,
and eMMC.
- Audio/Video, Camera & Display ports.
- Connectivity: RJ45 2.5GbE, WLAN/Bluetooth, CAN/CAN-FD.
- PCIe ports.
- USB & UART ports.
Compared to "monaco-evk" variant, which utilizes higher tier QCS8300-AA
SKU (supporting 40 TOPS of NPU) and a 4-PMIC (2x PM8650AU + Maxim MAX20018
+ TI TPS6594) power delivery network (PDN) to support higher power
requirement. This board utilizes lower tier QCS8300-AC SKU
(Supporting 20 TOPS of NPU) and a simplified 2 PMIC(2x PM8650AU) PDN.
Add support for the following components :
- GPI (Generic Peripheral Interface) and QUPv3-0/1
controllers to facilitate DMA and peripheral communication.
- TCA9534 I/O expander via I2C to provide 8 additional GPIO
lines for extended I/O functionality.
- USB1 controller routed to a TypeC connector in device mode to
support USB peripheral operations.
- Remoteproc subsystems for supported DSPs such as Audio DSP,
Compute DSP and Generic DSP, along with their corresponding
firmware.
- Configure nvmem-layout on the I2C EEPROM to store data for Ethernet
and other consumers.
- QCA8081 2.5G Ethernet PHY on port-0 and expose the
Ethernet MAC address via nvmem for network configuration.
It depends on CONFIG_QCA808X_PHY to use QCA8081 PHY.
- Support for the Iris video decoder, including the required
firmware, to enable video decoding capabilities.
- PCIe0 and PCIe1 controller and phy-nodes.
- Sound card and max98357a based I2S speaker amplifier.
Written with inputs from:
Nirmesh Kumar Singh <nirmesh.singh@oss.qualcomm.com> - GPIO
Expander.
Viken Dadhaniya <viken.dadhaniya@oss.qualcomm.com> - GPI/QUP.
Mohd Ayaan Anwar <mohd.anwar@oss.qualcomm.com> - Ethernet.
Monish Chunara <monish.chunara@oss.qualcomm.com> - EEPROM.
Swati Agarwal <swati.agarwal@oss.qualcomm.com> - USB.
Sushrut Shree Trivedi <sushrut.trivedi@oss.qualcomm.com> - PCIe.
Mohammad Rafi Shaik <mohammad.rafi.shaik@oss.qualcomm.com> - Audio.
Co-developed-by: Faruque Ansari <faruque.ansari@oss.qualcomm.com>
Signed-off-by: Faruque Ansari <faruque.ansari@oss.qualcomm.com>
Signed-off-by: Umang Chheda <umang.chheda@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
arch/arm64/boot/dts/qcom/monaco-evk-ac-sku.dts | 730 +++++++++++++++++++++++++
2 files changed, 731 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index c46d94bb6dd5..1d8c2a3db6c0 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -57,6 +57,7 @@ dtb-$(CONFIG_ARCH_QCOM) += mahua-crd.dtb
dtb-$(CONFIG_ARCH_QCOM) += milos-fairphone-fp6.dtb
dtb-$(CONFIG_ARCH_QCOM) += monaco-arduino-monza.dtb
dtb-$(CONFIG_ARCH_QCOM) += monaco-evk.dtb
+dtb-$(CONFIG_ARCH_QCOM) += monaco-evk-ac-sku.dtb
monaco-evk-camera-imx577-dtbs := monaco-evk.dtb monaco-evk-camera-imx577.dtbo
dtb-$(CONFIG_ARCH_QCOM) += monaco-evk-camera-imx577.dtb
diff --git a/arch/arm64/boot/dts/qcom/monaco-evk-ac-sku.dts b/arch/arm64/boot/dts/qcom/monaco-evk-ac-sku.dts
new file mode 100644
index 000000000000..c100ed9f7981
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/monaco-evk-ac-sku.dts
@@ -0,0 +1,730 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/sound/qcom,q6afe.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "monaco.dtsi"
+#include "monaco-pmics.dtsi"
+
+/ {
+ model = "Qualcomm Technologies, Inc. Monaco-ac-sku EVK";
+ compatible = "qcom,monaco-evk-ac-sku", "qcom,qcs8300";
+
+ aliases {
+ ethernet0 = ðernet0;
+ i2c1 = &i2c1;
+ serial0 = &uart7;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ dmic: audio-codec-0 {
+ compatible = "dmic-codec";
+ #sound-dai-cells = <0>;
+ num-channels = <1>;
+ };
+
+ max98357a: audio-codec-1 {
+ compatible = "maxim,max98357a";
+ #sound-dai-cells = <0>;
+ };
+
+ sound {
+ compatible = "qcom,qcs8275-sndcard";
+ model = "MONACO-EVK";
+
+ pinctrl-0 = <&hs0_mi2s_active>, <&mi2s1_active>;
+ pinctrl-names = "default";
+
+ hs0-mi2s-playback-dai-link {
+ link-name = "HS0 MI2S Playback";
+
+ codec {
+ sound-dai = <&max98357a>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai PRIMARY_MI2S_RX>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ sec-mi2s-capture-dai-link {
+ link-name = "Secondary MI2S Capture";
+
+ codec {
+ sound-dai = <&dmic>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai SECONDARY_MI2S_TX>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "a";
+
+ vreg_l3a: ldo3 {
+ regulator-name = "vreg_l3a";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4a: ldo4 {
+ regulator-name = "vreg_l4a";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5a: ldo5 {
+ regulator-name = "vreg_l5a";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6a: ldo6 {
+ regulator-name = "vreg_l6a";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7a: ldo7 {
+ regulator-name = "vreg_l7a";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8a: ldo8 {
+ regulator-name = "vreg_l8a";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9a: ldo9 {
+ regulator-name = "vreg_l9a";
+ regulator-min-microvolt = <2970000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s4a: smps4 {
+ regulator-name = "vreg_s4a";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s9a: smps9 {
+ regulator-name = "vreg_s9a";
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pmm8654au-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vreg_l1c: ldo1 {
+ regulator-name = "vreg_l1c";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <500000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2c: ldo2 {
+ regulator-name = "vreg_l2c";
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <904000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4c: ldo4 {
+ regulator-name = "vreg_l4c";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6c: ldo6 {
+ regulator-name = "vreg_l6c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7c: ldo7 {
+ regulator-name = "vreg_l7c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c: ldo8 {
+ regulator-name = "vreg_l8c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c: ldo9 {
+ regulator-name = "vreg_l9c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5c: smps5 {
+ regulator-name = "vreg_s5c";
+ regulator-min-microvolt = <1104000>;
+ regulator-max-microvolt = <1104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+ðernet0 {
+ phy-mode = "2500base-x";
+ phy-handle = <&hsgmii_phy0>;
+
+ pinctrl-0 = <ðernet0_default>;
+ pinctrl-names = "default";
+
+ snps,mtl-rx-config = <&mtl_rx_setup>;
+ snps,mtl-tx-config = <&mtl_tx_setup>;
+ nvmem-cells = <&mac_addr0>;
+ nvmem-cell-names = "mac-address";
+
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hsgmii_phy0: ethernet-phy@1c {
+ compatible = "ethernet-phy-id004d.d101";
+ reg = <0x1c>;
+ reset-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
+ reset-assert-us = <11000>;
+ reset-deassert-us = <70000>;
+ };
+ };
+
+ mtl_rx_setup: rx-queues-config {
+ snps,rx-queues-to-use = <4>;
+ snps,rx-sched-sp;
+
+ queue0 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x0>;
+ snps,route-up;
+ snps,priority = <0x1>;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ snps,map-to-dma-channel = <0x1>;
+ snps,route-ptp;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x2>;
+ snps,route-avcp;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,map-to-dma-channel = <0x3>;
+ snps,priority = <0xc>;
+ };
+ };
+
+ mtl_tx_setup: tx-queues-config {
+ snps,tx-queues-to-use = <4>;
+
+ queue0 {
+ snps,dcb-algorithm;
+ };
+
+ queue1 {
+ snps,dcb-algorithm;
+ };
+
+ queue2 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+
+ queue3 {
+ snps,avb-algorithm;
+ snps,send_slope = <0x1000>;
+ snps,idle_slope = <0x1000>;
+ snps,high_credit = <0x3e800>;
+ snps,low_credit = <0xffc18000>;
+ };
+ };
+};
+
+&gpi_dma0 {
+ status = "okay";
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&i2c1 {
+ pinctrl-0 = <&qup_i2c1_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ fan_controller: fan@18 {
+ compatible = "ti,amc6821";
+ reg = <0x18>;
+ #pwm-cells = <2>;
+
+ fan {
+ pwms = <&fan_controller 40000 PWM_POLARITY_INVERTED>;
+ };
+ };
+
+ eeprom0: eeprom@50 {
+ compatible = "atmel,24c256";
+ reg = <0x50>;
+ pagesize = <64>;
+
+ nvmem-layout {
+ compatible = "fixed-layout";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ mac_addr0: mac-addr@0 {
+ reg = <0x0 0x6>;
+ };
+ };
+ };
+};
+
+&i2c15 {
+ pinctrl-0 = <&qup_i2c15_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ expander0: gpio@38 {
+ compatible = "ti,tca9538";
+ reg = <0x38>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupts-extended = <&tlmm 56 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&expander0_int>;
+ pinctrl-names = "default";
+ };
+
+ expander1: gpio@39 {
+ compatible = "ti,tca9538";
+ reg = <0x39>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupts-extended = <&tlmm 16 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&expander1_int>;
+ pinctrl-names = "default";
+ };
+
+ expander2: gpio@3a {
+ compatible = "ti,tca9538";
+ reg = <0x3a>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupts-extended = <&tlmm 95 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&expander2_int>;
+ pinctrl-names = "default";
+ };
+
+ expander3: gpio@3b {
+ compatible = "ti,tca9538";
+ reg = <0x3b>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupts-extended = <&tlmm 24 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&expander3_int>;
+ pinctrl-names = "default";
+ };
+
+ expander4: gpio@3c {
+ compatible = "ti,tca9538";
+ reg = <0x3c>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupts-extended = <&tlmm 96 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&expander4_int>;
+ pinctrl-names = "default";
+ };
+
+ expander5: gpio@3d {
+ compatible = "ti,tca9538";
+ reg = <0x3d>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&expander5_int>;
+ pinctrl-names = "default";
+ };
+
+ expander6: gpio@3e {
+ compatible = "ti,tca9538";
+ reg = <0x3e>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ #interrupt-cells = <2>;
+ interrupt-controller;
+ interrupts-extended = <&tlmm 52 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-0 = <&expander6_int>;
+ pinctrl-names = "default";
+ };
+};
+
+&iris {
+ status = "okay";
+};
+
+&pcie0 {
+ pinctrl-0 = <&pcie0_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l6a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&pcie1 {
+ pinctrl-0 = <&pcie1_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie1_phy {
+ vdda-phy-supply = <&vreg_l6a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&pcieport0 {
+ reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
+};
+
+&pcieport1 {
+ reset-gpios = <&tlmm 23 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 21 GPIO_ACTIVE_HIGH>;
+};
+
+&qupv3_id_0 {
+ firmware-name = "qcom/qcs8300/qupv3fw.elf";
+
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ firmware-name = "qcom/qcs8300/qupv3fw.elf";
+
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/qcs8300/adsp.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ firmware-name = "qcom/qcs8300/cdsp0.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_gpdsp {
+ firmware-name = "qcom/qcs8300/gpdsp0.mbn";
+
+ status = "okay";
+};
+
+&serdes0 {
+ phy-supply = <&vreg_l4a>;
+
+ status = "okay";
+};
+
+&spi10 {
+ status = "okay";
+
+ tpm@0 {
+ compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ };
+};
+
+&tlmm {
+
+ pcie0_default_state: pcie0-default-state {
+ wake-pins {
+ pins = "gpio0";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ clkreq-pins {
+ pins = "gpio1";
+ function = "pcie0_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-pins {
+ pins = "gpio2";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ expander5_int: expander5-int-state {
+ pins = "gpio3";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ ethernet0_default: ethernet0-default-state {
+ ethernet0_mdc: ethernet0-mdc-pins {
+ pins = "gpio5";
+ function = "emac0_mdc";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+
+ ethernet0_mdio: ethernet0-mdio-pins {
+ pins = "gpio6";
+ function = "emac0_mdio";
+ drive-strength = <16>;
+ bias-pull-up;
+ };
+ };
+
+ expander1_int: expander1-int-state {
+ pins = "gpio16";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ qup_i2c1_default: qup-i2c1-state {
+ pins = "gpio19", "gpio20";
+ function = "qup0_se1";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ qup_i2c1_default: qup-i2c1-state {
+ pins = "gpio19", "gpio20";
+ function = "qup0_se1";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ pcie1_default_state: pcie1-default-state {
+ wake-pins {
+ pins = "gpio21";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ clkreq-pins {
+ pins = "gpio22";
+ function = "pcie1_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-pins {
+ pins = "gpio23";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ expander3_int: expander3-int-state {
+ pins = "gpio24";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ expander6_int: expander6-int-state {
+ pins = "gpio52";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ expander0_int: expander0-int-state {
+ pins = "gpio56";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ qup_i2c15_default: qup-i2c15-state {
+ pins = "gpio91", "gpio92";
+ function = "qup1_se7";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ expander2_int: expander2-int-state {
+ pins = "gpio95";
+ function = "gpio";
+ bias-pull-up;
+ };
+
+ expander4_int: expander4-int-state {
+ pins = "gpio96";
+ function = "gpio";
+ bias-pull-up;
+ };
+};
+
+&uart7 {
+ status = "okay";
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+ vcc-supply = <&vreg_l8a>;
+ vcc-max-microamp = <1100000>;
+ vccq-supply = <&vreg_l4c>;
+ vccq-max-microamp = <1200000>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l4a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
+
+&usb_1 {
+ dr_mode = "peripheral";
+
+ status = "okay";
+};
+
+&usb_1_hsphy {
+ vdda-pll-supply = <&vreg_l7a>;
+ vdda18-supply = <&vreg_l7c>;
+ vdda33-supply = <&vreg_l9a>;
+
+ status = "okay";
+};
+
+&usb_qmpphy {
+ vdda-phy-supply = <&vreg_l7a>;
+ vdda-pll-supply = <&vreg_l5a>;
+
+ status = "okay";
+};
--
2.34.1
^ permalink raw reply related [flat|nested] 9+ messages in thread