* [PATCH v3 0/2] Enable Display Port for Qualcomm SA8775P-ride platform @ 2024-11-14 9:54 Soutrik Mukhopadhyay 2024-11-14 9:54 ` [PATCH v3 1/2] arm64: dts: qcom: sa8775p: add DisplayPort device nodes Soutrik Mukhopadhyay 2024-11-14 9:55 ` [PATCH v3 2/2] arm64: dts: qcom: sa8775p-ride: Enable Display Port Soutrik Mukhopadhyay 0 siblings, 2 replies; 5+ messages in thread From: Soutrik Mukhopadhyay @ 2024-11-14 9:54 UTC (permalink / raw) To: andersson, konradybcio, robh, krzk+dt, conor+dt Cc: Soutrik Mukhopadhyay, linux-arm-msm, devicetree, linux-kernel, quic_riteshk, quic_vproddut, quic_abhinavk This series adds the DPTX0 and DPTX1 nodes, as a part of mdss0 on Qualcomm SA8775P SoC. It also enables Display Port on Qualcomm SA8775P-ride platform. --- This patch depends on following series: https://lore.kernel.org/all/20240816-sa8775p-mm-v3-v1-0-77d53c3c0cef@quicinc.com/ https://lore.kernel.org/all/20241019-patchv3_1-v5-0-d2fb72c9a845@quicinc.com/ https://lore.kernel.org/all/20241018070706.28980-1-quic_mukhopad@quicinc.com/ v2: Fixed review comments from Dmitry, Konrad and Bjorn - Added a new patchset to separate out the soc and board parts.[Konrad] - Patchset 1 now comprises of the soc parts and patchset 2 includes board specific changes.[Bjorn] - Patchset 2 enables all the DP ports validated on the sa8775p-ride platform.[Bjorn] - Fixed indentation errors in the dtsi file containing the soc information.[Dmitry][Konrad] - Updated clocks to be used by respective PHYs.[Dmitry] - Added mdss0_dp1 device node.[Dmitry] - Updated the names of PHYs using label prefix "mdssM_dpN" for clarity.[Bjorn] - Avoided use of referring any label in the board(dts) file in the dtsi(platform) file.[Bjorn] v3: Fixed review comments from Dmitry and other minor changes to prevent warnings and maintain alignment - Added specific DP connector node for each DP port validated in patchset 2.[Dmitry] - Updated the reg value to 1 for port 1 under mdss_mdp in patchset 1. - Fixed the register address space for mdss0_dp1 and mdss0_dp1_phy in alignment to the register address space for mdss0_dp0 and mdss0_dp0_phy, in patchset 1. --- Soutrik Mukhopadhyay (2): arm64: dts: qcom: sa8775p: add DisplayPort device nodes arm64: dts: qcom: sa8775p-ride: Enable Display Port arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi | 80 ++++++++ arch/arm64/boot/dts/qcom/sa8775p.dtsi | 216 ++++++++++++++++++++- 2 files changed, 295 insertions(+), 1 deletion(-) -- 2.17.1 ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v3 1/2] arm64: dts: qcom: sa8775p: add DisplayPort device nodes 2024-11-14 9:54 [PATCH v3 0/2] Enable Display Port for Qualcomm SA8775P-ride platform Soutrik Mukhopadhyay @ 2024-11-14 9:54 ` Soutrik Mukhopadhyay 2024-11-14 12:07 ` Dmitry Baryshkov 2024-11-14 9:55 ` [PATCH v3 2/2] arm64: dts: qcom: sa8775p-ride: Enable Display Port Soutrik Mukhopadhyay 1 sibling, 1 reply; 5+ messages in thread From: Soutrik Mukhopadhyay @ 2024-11-14 9:54 UTC (permalink / raw) To: andersson, konradybcio, robh, krzk+dt, conor+dt Cc: Soutrik Mukhopadhyay, linux-arm-msm, devicetree, linux-kernel, quic_riteshk, quic_vproddut, quic_abhinavk Add device tree nodes for the DPTX0 and DPTX1 controllers with their corresponding PHYs found on Qualcomm SA8775P SoC. Signed-off-by: Soutrik Mukhopadhyay <quic_mukhopad@quicinc.com> --- arch/arm64/boot/dts/qcom/sa8775p.dtsi | 216 +++++++++++++++++++++++++- 1 file changed, 215 insertions(+), 1 deletion(-) diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi index f7a9d1684a79..b272feae8da1 100644 --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi @@ -3343,6 +3343,25 @@ interrupt-parent = <&mdss0>; interrupts = <0>; + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + dpu_intf0_out: endpoint { + remote-endpoint = <&mdss0_dp0_in>; + }; + }; + + port@1 { + reg = <1>; + dpu_intf4_out: endpoint { + remote-endpoint = <&mdss0_dp1_in>; + }; + }; + }; + mdss0_mdp_opp_table: opp-table { compatible = "operating-points-v2"; @@ -3367,6 +3386,200 @@ }; }; }; + + mdss0_dp0_phy: phy@aec2a00 { + compatible = "qcom,sa8775p-edp-phy"; + + reg = <0x0 0xaec2a00 0x0 0x200>, + <0x0 0xaec2200 0x0 0xd0>, + <0x0 0xaec2600 0x0 0xd0>, + <0x0 0xaec2000 0x0 0x1c8>; + + clocks =<&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_AUX_CLK>, + <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>; + clock-names = "aux", + "cfg_ahb"; + + #clock-cells = <1>; + #phy-cells = <0>; + + status = "disabled"; + }; + + mdss0_dp1_phy: phy@aec5a00 { + compatible = "qcom,sa8775p-edp-phy"; + + reg = <0x0 0xaec5a00 0x0 0x200>, + <0x0 0xaec5200 0x0 0xd0>, + <0x0 0xaec5600 0x0 0xd0>, + <0x0 0xaec5000 0x0 0x1c8>; + + clocks =<&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_AUX_CLK>, + <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>; + clock-names = "aux", + "cfg_ahb"; + + #clock-cells = <1>; + #phy-cells = <0>; + + status = "disabled"; + }; + + mdss0_dp0: displayport-controller@af54000 { + compatible = "qcom,sa8775p-dp"; + + reg = <0x0 0xaf54000 0x0 0x104>, + <0x0 0xaf54200 0x0 0x0c0>, + <0x0 0xaf55000 0x0 0x770>, + <0x0 0xaf56000 0x0 0x09c>; + + interrupt-parent = <&mdss0>; + interrupts = <12>; + + clocks = <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>, + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_AUX_CLK>, + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_LINK_CLK>, + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>, + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_PIXEL0_CLK>; + clock-names = "core_iface", + "core_aux", + "ctrl_link", + "ctrl_link_iface", + "stream_pixel"; + assigned-clocks = <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>, + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>; + assigned-clock-parents = <&mdss0_dp0_phy 0>, <&mdss0_dp0_phy 1>; + phys = <&mdss0_dp0_phy>; + phy-names = "dp"; + + operating-points-v2 = <&dp_opp_table>; + power-domains = <&rpmhpd SA8775P_MMCX>; + + #sound-dai-cells = <0>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + mdss0_dp0_in: endpoint { + remote-endpoint = <&dpu_intf0_out>; + }; + }; + + port@1 { + reg = <1>; + + mdss0_dp0_out: endpoint { }; + }; + }; + + dp_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-160000000 { + opp-hz = /bits/ 64 <160000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-270000000 { + opp-hz = /bits/ 64 <270000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-540000000 { + opp-hz = /bits/ 64 <540000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-810000000 { + opp-hz = /bits/ 64 <810000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; + + mdss0_dp1: displayport-controller@af5c000 { + compatible = "qcom,sa8775p-dp"; + + reg = <0x0 0xaf5c000 0x0 0x104>, + <0x0 0xaf5c200 0x0 0x0c0>, + <0x0 0xaf5d000 0x0 0x770>, + <0x0 0xaf5e000 0x0 0x09c>; + + interrupt-parent = <&mdss0>; + interrupts = <13>; + + clocks = <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>, + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_AUX_CLK>, + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_LINK_CLK>, + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_LINK_INTF_CLK>, + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_PIXEL0_CLK>; + clock-names = "core_iface", + "core_aux", + "ctrl_link", + "ctrl_link_iface", + "stream_pixel"; + assigned-clocks = <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_LINK_CLK_SRC>, + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_PIXEL0_CLK_SRC>; + assigned-clock-parents = <&mdss0_dp1_phy 0>, <&mdss0_dp1_phy 1>; + phys = <&mdss0_dp1_phy>; + phy-names = "dp"; + + operating-points-v2 = <&dp1_opp_table>; + power-domains = <&rpmhpd SA8775P_MMCX>; + + #sound-dai-cells = <0>; + + status = "disabled"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + mdss0_dp1_in: endpoint { + remote-endpoint = <&dpu_intf4_out>; + }; + }; + + port@1 { + reg = <1>; + + mdss0_dp1_out: endpoint { }; + }; + }; + + dp1_opp_table: opp-table { + compatible = "operating-points-v2"; + + opp-160000000 { + opp-hz = /bits/ 64 <160000000>; + required-opps = <&rpmhpd_opp_low_svs>; + }; + + opp-270000000 { + opp-hz = /bits/ 64 <270000000>; + required-opps = <&rpmhpd_opp_svs>; + }; + + opp-540000000 { + opp-hz = /bits/ 64 <540000000>; + required-opps = <&rpmhpd_opp_svs_l1>; + }; + + opp-810000000 { + opp-hz = /bits/ 64 <810000000>; + required-opps = <&rpmhpd_opp_nom>; + }; + }; + }; }; dispcc0: clock-controller@af00000 { @@ -3376,7 +3589,8 @@ <&rpmhcc RPMH_CXO_CLK>, <&rpmhcc RPMH_CXO_CLK_A>, <&sleep_clk>, - <0>, <0>, <0>, <0>, + <&mdss0_dp0_phy 0>, <&mdss0_dp0_phy 1>, + <&mdss0_dp1_phy 0>, <&mdss0_dp1_phy 1>, <0>, <0>, <0>, <0>; power-domains = <&rpmhpd SA8775P_MMCX>; #clock-cells = <1>; -- 2.17.1 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v3 1/2] arm64: dts: qcom: sa8775p: add DisplayPort device nodes 2024-11-14 9:54 ` [PATCH v3 1/2] arm64: dts: qcom: sa8775p: add DisplayPort device nodes Soutrik Mukhopadhyay @ 2024-11-14 12:07 ` Dmitry Baryshkov 0 siblings, 0 replies; 5+ messages in thread From: Dmitry Baryshkov @ 2024-11-14 12:07 UTC (permalink / raw) To: Soutrik Mukhopadhyay Cc: andersson, konradybcio, robh, krzk+dt, conor+dt, linux-arm-msm, devicetree, linux-kernel, quic_riteshk, quic_vproddut, quic_abhinavk On Thu, Nov 14, 2024 at 03:24:59PM +0530, Soutrik Mukhopadhyay wrote: > Add device tree nodes for the DPTX0 and DPTX1 controllers > with their corresponding PHYs found on Qualcomm SA8775P SoC. > > Signed-off-by: Soutrik Mukhopadhyay <quic_mukhopad@quicinc.com> This most likely wasn't validated against DT schema. Please don't send unvalidated DT patches. > --- > arch/arm64/boot/dts/qcom/sa8775p.dtsi | 216 +++++++++++++++++++++++++- > 1 file changed, 215 insertions(+), 1 deletion(-) > > diff --git a/arch/arm64/boot/dts/qcom/sa8775p.dtsi b/arch/arm64/boot/dts/qcom/sa8775p.dtsi > index f7a9d1684a79..b272feae8da1 100644 > --- a/arch/arm64/boot/dts/qcom/sa8775p.dtsi > +++ b/arch/arm64/boot/dts/qcom/sa8775p.dtsi > @@ -3343,6 +3343,25 @@ > interrupt-parent = <&mdss0>; > interrupts = <0>; > > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + dpu_intf0_out: endpoint { > + remote-endpoint = <&mdss0_dp0_in>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + dpu_intf4_out: endpoint { > + remote-endpoint = <&mdss0_dp1_in>; > + }; > + }; > + }; > + > mdss0_mdp_opp_table: opp-table { > compatible = "operating-points-v2"; > > @@ -3367,6 +3386,200 @@ > }; > }; > }; > + > + mdss0_dp0_phy: phy@aec2a00 { > + compatible = "qcom,sa8775p-edp-phy"; > + > + reg = <0x0 0xaec2a00 0x0 0x200>, > + <0x0 0xaec2200 0x0 0xd0>, > + <0x0 0xaec2600 0x0 0xd0>, > + <0x0 0xaec2000 0x0 0x1c8>; > + > + clocks =<&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_AUX_CLK>, > + <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>; > + clock-names = "aux", > + "cfg_ahb"; > + > + #clock-cells = <1>; > + #phy-cells = <0>; > + > + status = "disabled"; > + }; > + > + mdss0_dp1_phy: phy@aec5a00 { > + compatible = "qcom,sa8775p-edp-phy"; > + > + reg = <0x0 0xaec5a00 0x0 0x200>, > + <0x0 0xaec5200 0x0 0xd0>, > + <0x0 0xaec5600 0x0 0xd0>, > + <0x0 0xaec5000 0x0 0x1c8>; > + > + clocks =<&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_AUX_CLK>, > + <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>; > + clock-names = "aux", > + "cfg_ahb"; > + > + #clock-cells = <1>; > + #phy-cells = <0>; > + > + status = "disabled"; > + }; > + > + mdss0_dp0: displayport-controller@af54000 { > + compatible = "qcom,sa8775p-dp"; > + > + reg = <0x0 0xaf54000 0x0 0x104>, > + <0x0 0xaf54200 0x0 0x0c0>, > + <0x0 0xaf55000 0x0 0x770>, > + <0x0 0xaf56000 0x0 0x09c>; No p1 region? > + > + interrupt-parent = <&mdss0>; > + interrupts = <12>; > + > + clocks = <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>, > + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_AUX_CLK>, > + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_LINK_CLK>, > + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_LINK_INTF_CLK>, > + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_PIXEL0_CLK>; > + clock-names = "core_iface", > + "core_aux", > + "ctrl_link", > + "ctrl_link_iface", > + "stream_pixel"; > + assigned-clocks = <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_LINK_CLK_SRC>, > + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX0_PIXEL0_CLK_SRC>; > + assigned-clock-parents = <&mdss0_dp0_phy 0>, <&mdss0_dp0_phy 1>; > + phys = <&mdss0_dp0_phy>; > + phy-names = "dp"; > + > + operating-points-v2 = <&dp_opp_table>; > + power-domains = <&rpmhpd SA8775P_MMCX>; > + > + #sound-dai-cells = <0>; > + > + status = "disabled"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + mdss0_dp0_in: endpoint { > + remote-endpoint = <&dpu_intf0_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + mdss0_dp0_out: endpoint { }; > + }; > + }; > + > + dp_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + opp-160000000 { > + opp-hz = /bits/ 64 <160000000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + }; > + > + opp-270000000 { > + opp-hz = /bits/ 64 <270000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-540000000 { > + opp-hz = /bits/ 64 <540000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + > + opp-810000000 { > + opp-hz = /bits/ 64 <810000000>; > + required-opps = <&rpmhpd_opp_nom>; > + }; > + }; > + }; > + > + mdss0_dp1: displayport-controller@af5c000 { > + compatible = "qcom,sa8775p-dp"; > + > + reg = <0x0 0xaf5c000 0x0 0x104>, > + <0x0 0xaf5c200 0x0 0x0c0>, > + <0x0 0xaf5d000 0x0 0x770>, > + <0x0 0xaf5e000 0x0 0x09c>; > + > + interrupt-parent = <&mdss0>; > + interrupts = <13>; > + > + clocks = <&dispcc0 MDSS_DISP_CC_MDSS_AHB_CLK>, > + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_AUX_CLK>, > + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_LINK_CLK>, > + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_LINK_INTF_CLK>, > + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_PIXEL0_CLK>; > + clock-names = "core_iface", > + "core_aux", > + "ctrl_link", > + "ctrl_link_iface", > + "stream_pixel"; > + assigned-clocks = <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_LINK_CLK_SRC>, > + <&dispcc0 MDSS_DISP_CC_MDSS_DPTX1_PIXEL0_CLK_SRC>; > + assigned-clock-parents = <&mdss0_dp1_phy 0>, <&mdss0_dp1_phy 1>; > + phys = <&mdss0_dp1_phy>; > + phy-names = "dp"; > + > + operating-points-v2 = <&dp1_opp_table>; > + power-domains = <&rpmhpd SA8775P_MMCX>; > + > + #sound-dai-cells = <0>; > + > + status = "disabled"; > + > + ports { > + #address-cells = <1>; > + #size-cells = <0>; > + > + port@0 { > + reg = <0>; > + > + mdss0_dp1_in: endpoint { > + remote-endpoint = <&dpu_intf4_out>; > + }; > + }; > + > + port@1 { > + reg = <1>; > + > + mdss0_dp1_out: endpoint { }; > + }; > + }; > + > + dp1_opp_table: opp-table { > + compatible = "operating-points-v2"; > + > + opp-160000000 { > + opp-hz = /bits/ 64 <160000000>; > + required-opps = <&rpmhpd_opp_low_svs>; > + }; > + > + opp-270000000 { > + opp-hz = /bits/ 64 <270000000>; > + required-opps = <&rpmhpd_opp_svs>; > + }; > + > + opp-540000000 { > + opp-hz = /bits/ 64 <540000000>; > + required-opps = <&rpmhpd_opp_svs_l1>; > + }; > + > + opp-810000000 { > + opp-hz = /bits/ 64 <810000000>; > + required-opps = <&rpmhpd_opp_nom>; > + }; > + }; > + }; > }; > > dispcc0: clock-controller@af00000 { > @@ -3376,7 +3589,8 @@ > <&rpmhcc RPMH_CXO_CLK>, > <&rpmhcc RPMH_CXO_CLK_A>, > <&sleep_clk>, > - <0>, <0>, <0>, <0>, > + <&mdss0_dp0_phy 0>, <&mdss0_dp0_phy 1>, > + <&mdss0_dp1_phy 0>, <&mdss0_dp1_phy 1>, > <0>, <0>, <0>, <0>; > power-domains = <&rpmhpd SA8775P_MMCX>; > #clock-cells = <1>; > -- > 2.17.1 > -- With best wishes Dmitry ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v3 2/2] arm64: dts: qcom: sa8775p-ride: Enable Display Port 2024-11-14 9:54 [PATCH v3 0/2] Enable Display Port for Qualcomm SA8775P-ride platform Soutrik Mukhopadhyay 2024-11-14 9:54 ` [PATCH v3 1/2] arm64: dts: qcom: sa8775p: add DisplayPort device nodes Soutrik Mukhopadhyay @ 2024-11-14 9:55 ` Soutrik Mukhopadhyay 2024-12-14 22:34 ` Konrad Dybcio 1 sibling, 1 reply; 5+ messages in thread From: Soutrik Mukhopadhyay @ 2024-11-14 9:55 UTC (permalink / raw) To: andersson, konradybcio, robh, krzk+dt, conor+dt Cc: Soutrik Mukhopadhyay, linux-arm-msm, devicetree, linux-kernel, quic_riteshk, quic_vproddut, quic_abhinavk Enable DPTX0 and DPTX1 along with their corresponding PHYs for sa8775p-ride platform. Signed-off-by: Soutrik Mukhopadhyay <quic_mukhopad@quicinc.com> --- arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi | 80 ++++++++++++++++++++++ 1 file changed, 80 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi b/arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi index adb71aeff339..4847e4942386 100644 --- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi +++ b/arch/arm64/boot/dts/qcom/sa8775p-ride.dtsi @@ -27,6 +27,30 @@ chosen { stdout-path = "serial0:115200n8"; }; + + dp0-connector { + compatible = "dp-connector"; + label = "DP0"; + type = "full-size"; + + port { + dp0_connector_in: endpoint { + remote-endpoint = <&mdss0_dp0_out>; + }; + }; + }; + + dp1-connector { + compatible = "dp-connector"; + label = "DP1"; + type = "full-size"; + + port { + dp1_connector_in: endpoint { + remote-endpoint = <&mdss0_dp1_out>; + }; + }; + }; }; &apps_rsc { @@ -421,6 +445,50 @@ status = "okay"; }; +&mdss0 { + status = "okay"; +}; + +&mdss0_dp0 { + status = "okay"; + + pinctrl-0 = <&dp0_hot_plug_det>; + pinctrl-names = "default"; +}; + +&mdss0_dp0_out { + data-lanes = <0 1 2 3>; + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; + remote-endpoint = <&dp0_connector_in>; +}; + +&mdss0_dp0_phy { + status = "okay"; + + vdda-phy-supply = <&vreg_l1c>; + vdda-pll-supply = <&vreg_l4a>; +}; + +&mdss0_dp1 { + status = "okay"; + + pinctrl-0 = <&dp1_hot_plug_det>; + pinctrl-names = "default"; +}; + +&mdss0_dp1_out { + data-lanes = <0 1 2 3>; + link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; + remote-endpoint = <&dp1_connector_in>; +}; + +&mdss0_dp1_phy { + status = "okay"; + + vdda-phy-supply = <&vreg_l1c>; + vdda-pll-supply = <&vreg_l4a>; +}; + &pmm8654au_0_gpios { gpio-line-names = "DS_EN", "POFF_COMPLETE", @@ -527,6 +595,18 @@ }; &tlmm { + dp0_hot_plug_det: dp0-hot-plug-det-state { + pins = "gpio101"; + function = "edp0_hot"; + bias-disable; + }; + + dp1_hot_plug_det: dp1-hot-plug-det-state { + pins = "gpio102"; + function = "edp1_hot"; + bias-disable; + }; + ethernet0_default: ethernet0-default-state { ethernet0_mdc: ethernet0-mdc-pins { pins = "gpio8"; -- 2.17.1 ^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH v3 2/2] arm64: dts: qcom: sa8775p-ride: Enable Display Port 2024-11-14 9:55 ` [PATCH v3 2/2] arm64: dts: qcom: sa8775p-ride: Enable Display Port Soutrik Mukhopadhyay @ 2024-12-14 22:34 ` Konrad Dybcio 0 siblings, 0 replies; 5+ messages in thread From: Konrad Dybcio @ 2024-12-14 22:34 UTC (permalink / raw) To: Soutrik Mukhopadhyay, andersson, konradybcio, robh, krzk+dt, conor+dt Cc: linux-arm-msm, devicetree, linux-kernel, quic_riteshk, quic_vproddut, quic_abhinavk On 14.11.2024 10:55 AM, Soutrik Mukhopadhyay wrote: > Enable DPTX0 and DPTX1 along with their corresponding PHYs for > sa8775p-ride platform. > > Signed-off-by: Soutrik Mukhopadhyay <quic_mukhopad@quicinc.com> > --- Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com> Konrad ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2024-12-14 22:34 UTC | newest] Thread overview: 5+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2024-11-14 9:54 [PATCH v3 0/2] Enable Display Port for Qualcomm SA8775P-ride platform Soutrik Mukhopadhyay 2024-11-14 9:54 ` [PATCH v3 1/2] arm64: dts: qcom: sa8775p: add DisplayPort device nodes Soutrik Mukhopadhyay 2024-11-14 12:07 ` Dmitry Baryshkov 2024-11-14 9:55 ` [PATCH v3 2/2] arm64: dts: qcom: sa8775p-ride: Enable Display Port Soutrik Mukhopadhyay 2024-12-14 22:34 ` Konrad Dybcio
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox