* [PATCH v4 0/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for Windows Dev Kit 2023
@ 2024-10-27 13:02 Jens Glathe via B4 Relay
2024-10-27 13:02 ` [PATCH v4 1/3] dt-bindings: arm: qcom: Add Microsoft " Jens Glathe via B4 Relay
` (3 more replies)
0 siblings, 4 replies; 8+ messages in thread
From: Jens Glathe via B4 Relay @ 2024-10-27 13:02 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Jens Glathe, Merck Hung
"Microsoft Windows Dev Kit 2023" aka "Blackrock" aka "Project Volterra"
Device tree for the Microsoft Windows Dev Kit 2023. This work
is based on the initial work of Merck Hung <merckhung@gmail.com>.
The Windows Dev Kit 2023 is a nice little desktop based on sc8280xp.
Link: https://learn.microsoft.com/en-us/windows/arm/dev-kit/
Supported features:
- USB type-c and type-a ports
- minidp connector
- built-in r8152 Ethernet adapter
- PCIe devices
- nvme
- ath11k WiFi (WCN6855)
- WCN6855 Bluetooth
- A690 GPU
- Venus codec
- ADSP and CDSP
- GPIO keys
- Audio definition (works via USB)
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Merck Hung <merckhung@gmail.com>
Original work: https://github.com/merckhung/linux_ms_dev_kit/blob/ms-dev-kit-2023-v6.3.0/arch/arm64/boot/dts/qcom/sc8280xp-microsoft-dev-kit-2023.dts
This dt is more or less deducted from the Thinkpad X13s.
It contains a lot of guesswork, and also a lot of research on
what works with the Windows Dev Kit.
The WiFi definition references qcom,ath11k-calibration-variant = "volterra"
which is unfortunately not yet in the linux-firmware. You can leave it out,
and the ath11k driver finds the default one for
"bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=0108,qmi-chip-id=2|18,qmi-board-id=255"
which is quite sub-optimal. I have placed a pr on github/qca-swiss-army-knife:
https://github.com/qca/qca-swiss-army-knife/pull/9 that provides an amended
board-2.bin and a board-2.json to generate it.
pcie2 (nvme) is intentionally specified as max-link-speed = <16>. The
interface is capable of it, most current nvme ssds are capable of it,
but the physical slot isn't. This leads to a silent downgrade to <8> instead
of the "device is limited by bus, capable of..." message.
It is in use and under development since May 2023, pretty stable now.
---
Changes in v4:
- removed the redundant regulator definitions
- changed the pinctrl property order
- use microsoft instead of MICROSOFT as subdirectory and device name component
- amend spacing in audio nodes
- change external connector dp1 for mini-dp to DP-3 for consistency
- Link to v3: https://lore.kernel.org/r/20241013-jg-blackrock-for-upstream-v3-0-839d3483a8e7@oldschoolsolutions.biz
Changes in v3:
- tried to heed all advice and comments given - thank you
- re-ordered patches to definition before use
- added "microsoft,blackrock" as compatible in QSEECOM driver
- removed the qseecom node
- ordered nodes alphabetically {address, node name, label}
- amended indentation
- consistently used blackrock as identifier / directory name
- sorted identifiers by the same order for multiple instances
- added some explanation re WiFi
- added definition for PMU on the WCN6855
- added some explanation for pcie2 max-link-speed
- Link to v2: https://lore.kernel.org/r/20240920-jg-blackrock-for-upstream-v2-0-9bf2f1b2191c@oldschoolsolutions.biz
Changes in v2:
- removed whitespaces and breaks
- added compatibility binding
- added feature list
- reformatted Signed-off list
- Link to v1: https://lore.kernel.org/r/5f5487e1-e458-4a3a-af02-c52e50ca1964@oldschoolsolutions.biz
---
Jens Glathe (3):
dt-bindings: arm: qcom: Add Microsoft Windows Dev Kit 2023
firmware: qcom: scm: Allow QSEECOM for Windows Dev Kit 2023
arm64: dts: qcom: sc8280xp-blackrock: dt definition for WDK2023
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/sc8280xp-microsoft-blackrock.dts | 1383 ++++++++++++++++++++
drivers/firmware/qcom/qcom_scm.c | 1 +
4 files changed, 1386 insertions(+)
---
base-commit: a39230ecf6b3057f5897bc4744a790070cfbe7a8
change-id: 20240920-jg-blackrock-for-upstream-7c7aca20e832
Best regards,
--
Jens Glathe <jens.glathe@oldschoolsolutions.biz>
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCH v4 1/3] dt-bindings: arm: qcom: Add Microsoft Windows Dev Kit 2023
2024-10-27 13:02 [PATCH v4 0/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for Windows Dev Kit 2023 Jens Glathe via B4 Relay
@ 2024-10-27 13:02 ` Jens Glathe via B4 Relay
2024-10-27 20:19 ` Krzysztof Kozlowski
2024-10-27 13:02 ` [PATCH v4 2/3] firmware: qcom: scm: Allow QSEECOM for " Jens Glathe via B4 Relay
` (2 subsequent siblings)
3 siblings, 1 reply; 8+ messages in thread
From: Jens Glathe via B4 Relay @ 2024-10-27 13:02 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Jens Glathe, Merck Hung
From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Add compatible values for the Microsoft Windows Dev Kit (WDK2023)
with its codename "blackrock". The Dev kit is a small desktop box
based on the mainboard of the Surface pro 9 5G, intended for
developers to test/build arm64-based Windows software.
Link: https://learn.microsoft.com/en-us/windows/arm/dev-kit/
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
1 file changed, 1 insertion(+)
diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 0f18cb35c774a..32381638b6f9e 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -823,6 +823,7 @@ properties:
- enum:
- lenovo,thinkpad-x13s
- microsoft,arcata
+ - microsoft,blackrock
- qcom,sc8280xp-crd
- qcom,sc8280xp-qrd
- const: qcom,sc8280xp
--
2.43.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v4 2/3] firmware: qcom: scm: Allow QSEECOM for Windows Dev Kit 2023
2024-10-27 13:02 [PATCH v4 0/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for Windows Dev Kit 2023 Jens Glathe via B4 Relay
2024-10-27 13:02 ` [PATCH v4 1/3] dt-bindings: arm: qcom: Add Microsoft " Jens Glathe via B4 Relay
@ 2024-10-27 13:02 ` Jens Glathe via B4 Relay
2024-10-27 13:02 ` [PATCH v4 3/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for WDK2023 Jens Glathe via B4 Relay
2024-10-29 12:44 ` [PATCH v4 0/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for Windows Dev Kit 2023 Rob Herring (Arm)
3 siblings, 0 replies; 8+ messages in thread
From: Jens Glathe via B4 Relay @ 2024-10-27 13:02 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Jens Glathe, Merck Hung
From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
add "microsoft,blackrock" as compatible device for QSEECOM
This is required to get access to efivars and uefi boot loader support.
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
drivers/firmware/qcom/qcom_scm.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index 4785386042252..f1b10c89b9638 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -1748,6 +1748,7 @@ static const struct of_device_id qcom_scm_qseecom_allowlist[] __maybe_unused = {
{ .compatible = "lenovo,thinkpad-x13s", },
{ .compatible = "lenovo,yoga-slim7x" },
{ .compatible = "microsoft,arcata", },
+ { .compatible = "microsoft,blackrock" },
{ .compatible = "microsoft,romulus13", },
{ .compatible = "microsoft,romulus15", },
{ .compatible = "qcom,sc8180x-primus" },
--
2.43.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCH v4 3/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for WDK2023
2024-10-27 13:02 [PATCH v4 0/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for Windows Dev Kit 2023 Jens Glathe via B4 Relay
2024-10-27 13:02 ` [PATCH v4 1/3] dt-bindings: arm: qcom: Add Microsoft " Jens Glathe via B4 Relay
2024-10-27 13:02 ` [PATCH v4 2/3] firmware: qcom: scm: Allow QSEECOM for " Jens Glathe via B4 Relay
@ 2024-10-27 13:02 ` Jens Glathe via B4 Relay
2024-10-29 20:18 ` Bjorn Andersson
2024-10-29 12:44 ` [PATCH v4 0/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for Windows Dev Kit 2023 Rob Herring (Arm)
3 siblings, 1 reply; 8+ messages in thread
From: Jens Glathe via B4 Relay @ 2024-10-27 13:02 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Jens Glathe, Merck Hung
From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Device tree for the Microsoft Windows Dev Kit 2023. This work
is based on the initial work of Merck Hung <merckhung@gmail.com>.
The Windows Dev Kit 2023 is a nice little desktop based on sc8280xp.
Link: https://learn.microsoft.com/en-us/windows/arm/dev-kit/
Supported features:
- USB type-c and type-a ports
- minidp connector
- built-in r8152 Ethernet adapter
- PCIe devices
- nvme
- ath11k WiFi (WCN6855)
- WCN6855 Bluetooth
- A690 GPU
- ADSP and CDSP
- GPIO keys
- Audio definition (works via USB)
Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Signed-off-by: Merck Hung <merckhung@gmail.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/sc8280xp-microsoft-blackrock.dts | 1383 ++++++++++++++++++++
2 files changed, 1384 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index ac199f809b0d4..0e354299f832b 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -192,6 +192,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc8180x-primus.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-lenovo-thinkpad-x13s.dtb
dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-microsoft-arcata.dtb
+dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-microsoft-blackrock.dtb
dtb-$(CONFIG_ARCH_QCOM) += sda660-inforce-ifc6560.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm450-lenovo-tbx605f.dtb
dtb-$(CONFIG_ARCH_QCOM) += sdm450-motorola-ali.dtb
diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dts b/arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dts
new file mode 100644
index 0000000000000..19ce7bb12c2e1
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dts
@@ -0,0 +1,1383 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2021, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2022, Linaro Limited
+ * Copyright (c) 2023, Merck Hung <merckhung@gmail.com>
+ * Copyright (c) 2023, 2024 Jens Glathe <jens.glathe@oldschoolsolutions.biz>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "sc8280xp.dtsi"
+#include "sc8280xp-pmics.dtsi"
+
+/ {
+ model = "Windows Dev Kit 2023";
+ compatible = "microsoft,blackrock", "qcom,sc8280xp";
+ chassis-type = "desktop";
+
+ aliases {
+ i2c4 = &i2c4;
+ i2c21 = &i2c21;
+ serial1 = &uart2;
+ };
+
+ wcd938x: audio-codec {
+ compatible = "qcom,wcd9380-codec";
+
+ pinctrl-0 = <&wcd_default>;
+ pinctrl-names = "default";
+
+ reset-gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+
+ vdd-buck-supply = <&vreg_s10b>;
+ vdd-rxtx-supply = <&vreg_s10b>;
+ vdd-io-supply = <&vreg_s10b>;
+ vdd-mic-bias-supply = <&vreg_bob>;
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+ #sound-dai-cells = <1>;
+ };
+
+ dp3_connector: connector {
+ compatible = "dp-connector";
+ label = "DP-3";
+ type = "mini";
+
+ dp-pwr-supply = <&vreg_misc_3p3>;
+
+ port {
+ dp1_connector_in: endpoint {
+ remote-endpoint = <&mdss0_dp2_phy_out>;
+ };
+ };
+ };
+
+ pmic-glink {
+ compatible = "qcom,sc8280xp-pmic-glink", "qcom,pmic-glink";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ orientation-gpios = <&tlmm 166 GPIO_ACTIVE_HIGH>,
+ <&tlmm 49 GPIO_ACTIVE_HIGH>;
+
+ /* Left-side rear port */
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "source";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_con0_hs: endpoint {
+ remote-endpoint = <&usb_0_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_con0_ss: endpoint {
+ remote-endpoint = <&usb_0_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_con0_sbu: endpoint {
+ remote-endpoint = <&usb0_sbu_mux>;
+ };
+ };
+ };
+ };
+
+ /* Left-side front port */
+ connector@1 {
+ compatible = "usb-c-connector";
+ reg = <1>;
+ power-role = "source";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_con1_hs: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_con1_ss: endpoint {
+ remote-endpoint = <&usb_1_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_con1_sbu: endpoint {
+ remote-endpoint = <&usb1_sbu_mux>;
+ };
+ };
+ };
+ };
+ };
+
+ vreg_misc_3p3: regulator-misc-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VCC3B";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmc8280_1_gpios 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&misc_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ vreg_nvme: regulator-nvme {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VCC3_SSD";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 135 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&nvme_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_vph_pwr: regulator-vph-pwr {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VPH_VCC3R9";
+ regulator-min-microvolt = <3900000>;
+ regulator-max-microvolt = <3900000>;
+
+ regulator-always-on;
+ };
+
+ vreg_wlan: regulator-wlan {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VCC_WLAN_3R9";
+ regulator-min-microvolt = <3900000>;
+ regulator-max-microvolt = <3900000>;
+
+ gpio = <&pmr735a_gpios 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&hastings_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_wwan: regulator-wwan {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VCC3B_WAN";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmc8280_2_gpios 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&wwan_sw_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ reserved-memory {
+ gpu_mem: gpu-mem@8bf00000 {
+ reg = <0 0x8bf00000 0 0x2000>;
+ no-map;
+ };
+
+ linux,cma {
+ compatible = "shared-dma-pool";
+ size = <0x0 0x8000000>;
+ reusable;
+ linux,cma-default;
+ };
+ };
+
+ usb0-sbu-mux {
+ compatible = "pericom,pi3usb102", "gpio-sbu-mux";
+
+ enable-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
+ select-gpios = <&tlmm 164 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&usb0_sbu_default>;
+ pinctrl-names = "default";
+
+ mode-switch;
+ orientation-switch;
+
+ port {
+ usb0_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_con0_sbu>;
+ };
+ };
+ };
+
+ usb1-sbu-mux {
+ compatible = "pericom,pi3usb102", "gpio-sbu-mux";
+
+ enable-gpios = <&tlmm 48 GPIO_ACTIVE_LOW>;
+ select-gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&usb1_sbu_default>;
+ pinctrl-names = "default";
+
+ mode-switch;
+ orientation-switch;
+
+ port {
+ usb1_sbu_mux: endpoint {
+ remote-endpoint = <&pmic_glink_con1_sbu>;
+ };
+ };
+ };
+
+ wcn6855-pmu {
+ compatible = "qcom,wcn6855-pmu";
+
+ pinctrl-0 = <&bt_default>, <&wlan_en>;
+ pinctrl-names = "default";
+
+ wlan-enable-gpios = <&tlmm 134 GPIO_ACTIVE_HIGH>;
+ bt-enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>;
+
+ vddio-supply = <&vreg_s10b>;
+ vddaon-supply = <&vreg_s12b>;
+ vddpmu-supply = <&vreg_s12b>;
+ vddrfa0p95-supply = <&vreg_s12b>;
+ vddrfa1p3-supply = <&vreg_s11b>;
+ vddrfa1p9-supply = <&vreg_s1c>;
+ vddpcie1p3-supply = <&vreg_s11b>;
+ vddpcie1p9-supply = <&vreg_s1c>;
+
+ regulators {
+ vreg_pmu_rfa_cmn_0p8: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn_0p8";
+ };
+
+ vreg_pmu_aon_0p8: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p8";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p8: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p8";
+ };
+
+ vreg_pmu_btcmx_0p8: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p8";
+ };
+
+ vreg_pmu_pcie_1p8: ldo5 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+
+ vreg_pmu_pcie_0p9: ldo6 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_rfa_0p8: ldo7 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo8 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p7: ldo9 {
+ regulator-name = "vreg_pmu_rfa_1p7";
+ };
+ };
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8350-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-s10-supply = <&vreg_vph_pwr>;
+ vdd-s11-supply = <&vreg_vph_pwr>;
+ vdd-s12-supply = <&vreg_vph_pwr>;
+ vdd-l1-l4-supply = <&vreg_s12b>;
+ vdd-l2-l7-supply = <&vreg_bob>;
+ vdd-l3-l5-supply = <&vreg_s11b>;
+ vdd-l6-l9-l10-supply = <&vreg_s12b>;
+ vdd-l8-supply = <&vreg_s12b>;
+
+ vreg_s10b: smps10 {
+ regulator-name = "vreg_s10b";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_s11b: smps11 {
+ regulator-name = "vreg_s11b";
+ regulator-min-microvolt = <1272000>;
+ regulator-max-microvolt = <1272000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s12b: smps12 {
+ regulator-name = "vreg_s12b";
+ regulator-min-microvolt = <984000>;
+ regulator-max-microvolt = <984000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1b: ldo1 {
+ regulator-name = "vreg_l1b";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3b: ldo3 {
+ regulator-name = "vreg_l3b";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-boot-on;
+ };
+
+ vreg_l4b: ldo4 {
+ regulator-name = "vreg_l4b";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b: ldo6 {
+ regulator-name = "vreg_l6b";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-boot-on;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8350c-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-bob-supply = <&vreg_vph_pwr>;
+ vdd-l1-l12-supply = <&vreg_s1c>;
+ vdd-l2-l8-supply = <&vreg_s1c>;
+ vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
+ vdd-l6-l9-l11-supply = <&vreg_bob>;
+ vdd-l10-supply = <&vreg_s11b>;
+
+ vreg_s1c: smps1 {
+ regulator-name = "vreg_s1c";
+ regulator-min-microvolt = <1880000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-always-on;
+ };
+
+ vreg_l1c: ldo1 {
+ regulator-name = "vreg_l1c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6c: ldo6 {
+ regulator-name = "vreg_l6c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7c: ldo7 {
+ regulator-name = "vreg_l7c";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8c: ldo8 {
+ regulator-name = "vreg_l8c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9c: ldo9 {
+ regulator-name = "vreg_l9c";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12c: ldo12 {
+ regulator-name = "vreg_l12c";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13c: ldo13 {
+ regulator-name = "vreg_l13c";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob: bob {
+ regulator-name = "vreg_bob";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
+ regulator-always-on;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pm8350-rpmh-regulators";
+ qcom,pmic-id = "d";
+
+ vdd-l1-l4-supply = <&vreg_s11b>;
+ vdd-l2-l7-supply = <&vreg_bob>;
+ vdd-l3-l5-supply = <&vreg_s11b>;
+ vdd-l6-l9-l10-supply = <&vreg_s12b>;
+ vdd-l8-supply = <&vreg_s12b>;
+
+ vreg_l2d: ldo2 {
+ regulator-name = "vreg_l2d";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3d: ldo3 {
+ regulator-name = "vreg_l3d";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4d: ldo4 {
+ regulator-name = "vreg_l4d";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6d: ldo6 {
+ regulator-name = "vreg_l6d";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7d: ldo7 {
+ regulator-name = "vreg_l7d";
+ regulator-min-microvolt = <3072000>;
+ regulator-max-microvolt = <3072000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8d: ldo8 {
+ regulator-name = "vreg_l8d";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9d: ldo9 {
+ regulator-name = "vreg_l9d";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10d: ldo10 {
+ regulator-name = "vreg_l10d";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&dispcc0 {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+
+ zap-shader {
+ memory-region = <&gpu_mem>;
+ firmware-name = "qcom/sc8280xp/microsoft/blackrock/qcdxkmsuc8280.mbn";
+ };
+};
+
+&mdss0 {
+ status = "okay";
+};
+
+&mdss0_dp0 {
+ status = "okay";
+};
+
+&mdss0_dp0_out {
+ data-lanes = <0 1>;
+ remote-endpoint = <&usb_0_qmpphy_dp_in>;
+};
+
+&mdss0_dp1 {
+ status = "okay";
+};
+
+&mdss0_dp1_out {
+ data-lanes = <0 1>;
+ remote-endpoint = <&usb_1_qmpphy_dp_in>;
+};
+
+&mdss0_dp2 {
+ compatible = "qcom,sc8280xp-dp";
+
+ data-lanes = <0 1 2 3>;
+
+ status = "okay";
+
+ ports {
+ port@1 {
+ reg = <1>;
+ mdss0_dp2_phy_out: endpoint {
+ remote-endpoint = <&dp1_connector_in>;
+ };
+ };
+ };
+};
+
+&mdss0_dp2_phy {
+ compatible = "qcom,sc8280xp-dp-phy";
+
+ vdda-phy-supply = <&vreg_l3b>;
+ vdda-pll-supply = <&vreg_l6b>;
+
+ status = "okay";
+};
+
+&pcie2a {
+ aspm-no-l0s;
+ max-link-speed = <16>;
+
+ perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
+
+ vddpe-3v3-supply = <&vreg_nvme>;
+ vdda-supply = <&vreg_l7d>;
+
+ pinctrl-0 = <&pcie2a_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie2a_phy {
+ vdda-phy-supply = <&vreg_l4d>;
+ vdda-pll-supply = <&vreg_l6d>;
+
+ status = "okay";
+};
+
+&pcie4 {
+ aspm-no-l0s;
+ max-link-speed = <2>;
+
+ perst-gpios = <&tlmm 141 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 139 GPIO_ACTIVE_LOW>;
+
+ vddpe-3v3-supply = <&vreg_wlan>;
+ vdda-supply = <&vreg_l7d>;
+
+ pinctrl-0 = <&pcie4_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie4_port0 {
+ wifi@0 {
+ compatible = "pci17cb,1103";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
+ vddaon-supply = <&vreg_pmu_aon_0p8>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+
+ qcom,ath11k-calibration-variant = "volterra";
+ };
+};
+
+&pcie4_phy {
+ vdda-phy-supply = <&vreg_l4d>;
+ vdda-pll-supply = <&vreg_l6d>;
+
+ status = "okay";
+};
+
+&pmc8280c_lpg {
+ status = "okay";
+};
+
+&pmk8280_adc_tm {
+ status = "okay";
+
+ sys-therm@0 {
+ reg = <0>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@1 {
+ reg = <1>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@2 {
+ reg = <2>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@3 {
+ reg = <3>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@4 {
+ reg = <4>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM1_100K_PU(3)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@5 {
+ reg = <5>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM2_100K_PU(3)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@6 {
+ reg = <6>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM3_100K_PU(3)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+
+ sys-therm@7 {
+ reg = <7>;
+ io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM4_100K_PU(3)>;
+ qcom,hw-settle-time-us = <200>;
+ qcom,avg-samples = <2>;
+ qcom,ratiometric;
+ };
+};
+
+&pmk8280_pon_pwrkey {
+ status = "okay";
+};
+
+&pmk8280_pon_resin {
+ status = "okay";
+};
+
+&pmk8280_rtc {
+ nvmem-cells = <&rtc_offset>;
+ nvmem-cell-names = "offset";
+
+ status = "okay";
+};
+
+&pmk8280_sdam_6 {
+ status = "okay";
+
+ rtc_offset: rtc-offset@bc {
+ reg = <0xbc 0x4>;
+ };
+};
+
+&pmk8280_vadc {
+ channel@144 {
+ reg = <PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm1";
+ };
+
+ channel@145 {
+ reg = <PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm2";
+ };
+
+ channel@146 {
+ reg = <PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm3";
+ };
+
+ channel@147 {
+ reg = <PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm4";
+ };
+
+ channel@344 {
+ reg = <PM8350_ADC7_AMUX_THM1_100K_PU(3)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm5";
+ };
+
+ channel@345 {
+ reg = <PM8350_ADC7_AMUX_THM2_100K_PU(3)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm6";
+ };
+
+ channel@346 {
+ reg = <PM8350_ADC7_AMUX_THM3_100K_PU(3)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm7";
+ };
+
+ channel@347 {
+ reg = <PM8350_ADC7_AMUX_THM4_100K_PU(3)>;
+ qcom,hw-settle-time = <200>;
+ qcom,ratiometric;
+ label = "sys_therm8";
+ };
+};
+
+&qup0 {
+ status = "okay";
+};
+
+&qup1 {
+ status = "okay";
+};
+
+&qup2 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sc8280xp/microsoft/blackrock/qcadsp8280.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_nsp0 {
+ firmware-name = "qcom/sc8280xp/microsoft/blackrock/qccdsp8280.mbn";
+
+ status = "okay";
+};
+
+&rxmacro {
+ status = "okay";
+};
+
+&sound {
+ compatible = "qcom,sc8280xp-sndcard";
+ model = "microsoft/blackrock";
+ audio-routing =
+ "SpkrLeft IN", "WSA_SPK1 OUT",
+ "SpkrRight IN", "WSA_SPK2 OUT",
+ "IN1_HPHL", "HPHL_OUT",
+ "IN2_HPHR", "HPHR_OUT",
+ "AMIC2", "MIC BIAS2",
+ "VA DMIC0", "MIC BIAS1",
+ "VA DMIC1", "MIC BIAS1",
+ "VA DMIC2", "MIC BIAS3",
+ "VA DMIC0", "VA MIC BIAS1",
+ "VA DMIC1", "VA MIC BIAS1",
+ "VA DMIC2", "VA MIC BIAS3",
+ "TX SWR_ADC1", "ADC2_OUTPUT";
+
+ wcd-playback-dai-link {
+ link-name = "WCD Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wcd-capture-dai-link {
+ link-name = "WCD Capture";
+
+ cpu {
+ sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+ };
+
+ codec {
+ sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wsa-dai-link {
+ link-name = "WSA Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&swr0 0>, <&wsamacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ va-dai-link {
+ link-name = "VA Capture";
+
+ cpu {
+ sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+
+ codec {
+ sound-dai = <&vamacro 0>;
+ };
+ };
+};
+
+&swr0 {
+ status = "okay";
+};
+
+&swr1 {
+ status = "okay";
+
+ wcd_rx: wcd9380-rx@0,4 {
+ compatible = "sdw20217010d00";
+ reg = <0 4>;
+ qcom,rx-port-mapping = <1 2 3 4 5>;
+ };
+};
+
+&swr2 {
+ status = "okay";
+
+ wcd_tx: wcd9380-tx@0,3 {
+ compatible = "sdw20217010d00";
+ reg = <0 3>;
+ qcom,tx-port-mapping = <1 1 2 3>;
+ };
+};
+
+&txmacro {
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-0 = <&uart2_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn6855-bt";
+
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
+ vddaon-supply = <&vreg_pmu_aon_0p8>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
+ vddbtcmx-supply = <&vreg_pmu_btcmx_0p8>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
+
+ max-speed = <3200000>;
+ };
+};
+
+&usb_0 {
+ status = "okay";
+};
+
+&usb_0_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_0_dwc3_hs {
+ remote-endpoint = <&pmic_glink_con0_hs>;
+};
+
+&usb_0_hsphy {
+ vdda-pll-supply = <&vreg_l9d>;
+ vdda-phy-supply = <&vreg_l4d>;
+ vdda18-supply = <&vreg_l1c>;
+ vdda33-supply = <&vreg_l7d>;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy {
+ vdda-phy-supply = <&vreg_l4d>;
+ vdda-pll-supply = <&vreg_l9d>;
+
+ orientation-switch;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy_dp_in {
+ remote-endpoint = <&mdss0_dp0_out>;
+};
+
+&usb_0_qmpphy_out {
+ remote-endpoint = <&pmic_glink_con0_ss>;
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3 {
+ dr_mode = "host";
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_con1_hs>;
+};
+
+&usb_1_hsphy {
+ vdda-pll-supply = <&vreg_l4b>;
+ vdda-phy-supply = <&vreg_l3b>;
+ vdda18-supply = <&vreg_l1c>;
+ vdda33-supply = <&vreg_l13c>;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy {
+ vdda-phy-supply = <&vreg_l3b>;
+ vdda-pll-supply = <&vreg_l4b>;
+
+ orientation-switch;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy_dp_in {
+ remote-endpoint = <&mdss0_dp1_out>;
+};
+
+&usb_1_qmpphy_out {
+ remote-endpoint = <&pmic_glink_con1_ss>;
+};
+
+&usb_2 {
+ pinctrl-0 = <&usb2_en_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&usb_2_dwc3 {
+ dr_mode = "host";
+ phy-names = "usb2-port0", "usb3-port0";
+ phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy0 {
+ vdda-pll-supply = <&vreg_l1b>;
+ vdda-phy-supply = <&vreg_l3d>;
+ vdda18-supply = <&vreg_l1c>;
+ vdda33-supply = <&vreg_l7d>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy1 {
+ vdda-pll-supply = <&vreg_l8d>;
+ vdda-phy-supply = <&vreg_l3d>;
+ vdda18-supply = <&vreg_l1c>;
+ vdda33-supply = <&vreg_l7d>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy2 {
+ vdda-pll-supply = <&vreg_l10d>;
+ vdda-phy-supply = <&vreg_l3d>;
+ vdda18-supply = <&vreg_l8c>;
+ vdda33-supply = <&vreg_l2d>;
+
+ status = "okay";
+};
+
+&usb_2_hsphy3 {
+ vdda-pll-supply = <&vreg_l10d>;
+ vdda-phy-supply = <&vreg_l3d>;
+ vdda18-supply = <&vreg_l8c>;
+ vdda33-supply = <&vreg_l2d>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy0 {
+ vdda-phy-supply = <&vreg_l1b>;
+ vdda-pll-supply = <&vreg_l4d>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy1 {
+ vdda-phy-supply = <&vreg_l8d>;
+ vdda-pll-supply = <&vreg_l4d>;
+
+ status = "okay";
+};
+
+&vamacro {
+ pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+ pinctrl-names = "default";
+
+ vdd-micb-supply = <&vreg_s10b>;
+
+ qcom,dmic-sample-rate = <4800000>;
+
+ status = "okay";
+};
+
+&wsamacro {
+ status = "okay";
+};
+
+&xo_board_clk {
+ clock-frequency = <38400000>;
+};
+
+/* PINCTRL */
+
+&lpass_tlmm {
+ status = "okay";
+};
+
+&pmc8280_1_gpios {
+ edp_bl_en: edp-bl-en-state {
+ pins = "gpio8";
+ function = "normal";
+ };
+
+ edp_bl_reg_en: edp-bl-reg-en-state {
+ pins = "gpio9";
+ function = "normal";
+ };
+
+ misc_3p3_reg_en: misc-3p3-reg-en-state {
+ pins = "gpio1";
+ function = "normal";
+ };
+};
+
+&pmc8280_2_gpios {
+ wwan_sw_en: wwan-sw-en-state {
+ pins = "gpio1";
+ function = "normal";
+ };
+};
+
+&pmc8280c_gpios {
+ edp_bl_pwm: edp-bl-pwm-state {
+ pins = "gpio8";
+ function = "func1";
+ };
+};
+
+&pmr735a_gpios {
+ hastings_reg_en: hastings-reg-en-state {
+ pins = "gpio1";
+ function = "normal";
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <70 2>, <74 6>, <125 2>, <128 2>, <154 4>;
+
+ bt_default: bt-default-state {
+ hstp-bt-en-pins {
+ pins = "gpio133";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ hstp-sw-ctrl-pins {
+ pins = "gpio132";
+ function = "gpio";
+ bias-pull-down;
+ };
+ };
+
+ nvme_reg_en: nvme-reg-en-state {
+ pins = "gpio135";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ pcie2a_default: pcie2a-default-state {
+ clkreq-n-pins {
+ pins = "gpio142";
+ function = "pcie2a_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio143";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio145";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie3a_default: pcie3a-default-state {
+ clkreq-n-pins {
+ pins = "gpio150";
+ function = "pcie3a_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio151";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio148";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie4_default: pcie4-default-state {
+ clkreq-n-pins {
+ pins = "gpio140";
+ function = "pcie4_clkreq";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio141";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio139";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ uart2_default: uart2-default-state {
+ cts-pins {
+ pins = "gpio121";
+ function = "qup2";
+ bias-bus-hold;
+ };
+
+ rts-pins {
+ pins = "gpio122";
+ function = "qup2";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rx-pins {
+ pins = "gpio124";
+ function = "qup2";
+ bias-pull-up;
+ };
+
+ tx-pins {
+ pins = "gpio123";
+ function = "qup2";
+ drive-strength = <2>;
+ bias-disable;
+ };
+ };
+
+ usb0_sbu_default: usb0-sbu-state {
+ oe-n-pins {
+ pins = "gpio101";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ output-high;
+ };
+
+ sel-pins {
+ pins = "gpio164";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ };
+ };
+
+ usb1_sbu_default: usb1-sbu-state {
+ oe-n-pins {
+ pins = "gpio48";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ output-high;
+ };
+
+ sel-pins {
+ pins = "gpio47";
+ function = "gpio";
+ bias-disable;
+ drive-strength = <16>;
+ };
+ };
+
+ usb2_en_state: usb2-en-state {
+ /* TS3USB221A USB2.0 mux select */
+ pins = "gpio24";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ wcd_default: wcd-default-state {
+ reset-pins {
+ pins = "gpio106";
+ function = "gpio";
+ bias-disable;
+ };
+ };
+
+ wlan_en: wlan-en-state {
+ pins = "gpio134";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+};
--
2.43.0
^ permalink raw reply related [flat|nested] 8+ messages in thread
* Re: [PATCH v4 1/3] dt-bindings: arm: qcom: Add Microsoft Windows Dev Kit 2023
2024-10-27 13:02 ` [PATCH v4 1/3] dt-bindings: arm: qcom: Add Microsoft " Jens Glathe via B4 Relay
@ 2024-10-27 20:19 ` Krzysztof Kozlowski
2024-10-27 20:20 ` Krzysztof Kozlowski
0 siblings, 1 reply; 8+ messages in thread
From: Krzysztof Kozlowski @ 2024-10-27 20:19 UTC (permalink / raw)
To: Jens Glathe
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-arm-msm, devicetree, linux-kernel, Merck Hung
On Sun, Oct 27, 2024 at 02:02:16PM +0100, Jens Glathe wrote:
> Add compatible values for the Microsoft Windows Dev Kit (WDK2023)
> with its codename "blackrock". The Dev kit is a small desktop box
> based on the mainboard of the Surface pro 9 5G, intended for
> developers to test/build arm64-based Windows software.
> Link: https://learn.microsoft.com/en-us/windows/arm/dev-kit/
>
> Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
> ---
> Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
> 1 file changed, 1 insertion(+)
>
---
<form letter>
This is an automated instruction, just in case, because many review tags
are being ignored. If you know the process, you can skip it (please do
not feel offended by me posting it here - no bad intentions intended).
If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions, under or above your Signed-off-by tag. Tag is "received", when
provided in a message replied to you on the mailing list. Tools like b4
can help here. However, there's no need to repost patches *only* to add
the tags. The upstream maintainer will do that for tags received on the
version they apply.
https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
</form letter>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v4 1/3] dt-bindings: arm: qcom: Add Microsoft Windows Dev Kit 2023
2024-10-27 20:19 ` Krzysztof Kozlowski
@ 2024-10-27 20:20 ` Krzysztof Kozlowski
0 siblings, 0 replies; 8+ messages in thread
From: Krzysztof Kozlowski @ 2024-10-27 20:20 UTC (permalink / raw)
To: Jens Glathe
Cc: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, linux-arm-msm, devicetree, linux-kernel, Merck Hung
On 27/10/2024 21:19, Krzysztof Kozlowski wrote:
> On Sun, Oct 27, 2024 at 02:02:16PM +0100, Jens Glathe wrote:
>> Add compatible values for the Microsoft Windows Dev Kit (WDK2023)
>> with its codename "blackrock". The Dev kit is a small desktop box
>> based on the mainboard of the Surface pro 9 5G, intended for
>> developers to test/build arm64-based Windows software.
>> Link: https://learn.microsoft.com/en-us/windows/arm/dev-kit/
>>
>> Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
>> ---
>> Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
>> 1 file changed, 1 insertion(+)
>>
>
> ---
>
> <form letter>
> This is an automated instruction, just in case, because many review tags
> are being ignored. If you know the process, you can skip it (please do
> not feel offended by me posting it here - no bad intentions intended).
> If you do not know the process, here is a short explanation:
>
> Please add Acked-by/Reviewed-by/Tested-by tags when posting new
> versions, under or above your Signed-off-by tag. Tag is "received", when
> provided in a message replied to you on the mailing list. Tools like b4
> can help here. However, there's no need to repost patches *only* to add
> the tags. The upstream maintainer will do that for tags received on the
> version they apply.
>
> https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
> </form letter>
Wrong template. Should be this one:
<form letter>
This is a friendly reminder during the review process.
It looks like you received a tag and forgot to add it.
If you do not know the process, here is a short explanation:
Please add Acked-by/Reviewed-by/Tested-by tags when posting new
versions, under or above your Signed-off-by tag. Tag is "received", when
provided in a message replied to you on the mailing list. Tools like b4
can help here. However, there's no need to repost patches *only* to add
the tags. The upstream maintainer will do that for tags received on the
version they apply.
https://elixir.bootlin.com/linux/v6.5-rc3/source/Documentation/process/submitting-patches.rst#L577
If a tag was not added on purpose, please state why and what changed.
</form letter>
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v4 0/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for Windows Dev Kit 2023
2024-10-27 13:02 [PATCH v4 0/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for Windows Dev Kit 2023 Jens Glathe via B4 Relay
` (2 preceding siblings ...)
2024-10-27 13:02 ` [PATCH v4 3/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for WDK2023 Jens Glathe via B4 Relay
@ 2024-10-29 12:44 ` Rob Herring (Arm)
3 siblings, 0 replies; 8+ messages in thread
From: Rob Herring (Arm) @ 2024-10-29 12:44 UTC (permalink / raw)
To: Jens Glathe
Cc: Bjorn Andersson, Merck Hung, linux-kernel, Krzysztof Kozlowski,
linux-arm-msm, Conor Dooley, devicetree, Konrad Dybcio
On Sun, 27 Oct 2024 14:02:15 +0100, Jens Glathe wrote:
> "Microsoft Windows Dev Kit 2023" aka "Blackrock" aka "Project Volterra"
>
> Device tree for the Microsoft Windows Dev Kit 2023. This work
> is based on the initial work of Merck Hung <merckhung@gmail.com>.
>
> The Windows Dev Kit 2023 is a nice little desktop based on sc8280xp.
> Link: https://learn.microsoft.com/en-us/windows/arm/dev-kit/
>
> Supported features:
> - USB type-c and type-a ports
> - minidp connector
> - built-in r8152 Ethernet adapter
> - PCIe devices
> - nvme
> - ath11k WiFi (WCN6855)
> - WCN6855 Bluetooth
> - A690 GPU
> - Venus codec
> - ADSP and CDSP
> - GPIO keys
> - Audio definition (works via USB)
>
> Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
> Signed-off-by: Merck Hung <merckhung@gmail.com>
>
> Original work: https://github.com/merckhung/linux_ms_dev_kit/blob/ms-dev-kit-2023-v6.3.0/arch/arm64/boot/dts/qcom/sc8280xp-microsoft-dev-kit-2023.dts
>
> This dt is more or less deducted from the Thinkpad X13s.
> It contains a lot of guesswork, and also a lot of research on
> what works with the Windows Dev Kit.
>
> The WiFi definition references qcom,ath11k-calibration-variant = "volterra"
> which is unfortunately not yet in the linux-firmware. You can leave it out,
> and the ath11k driver finds the default one for
> "bus=pci,vendor=17cb,device=1103,subsystem-vendor=17cb,subsystem-device=0108,qmi-chip-id=2|18,qmi-board-id=255"
> which is quite sub-optimal. I have placed a pr on github/qca-swiss-army-knife:
> https://github.com/qca/qca-swiss-army-knife/pull/9 that provides an amended
> board-2.bin and a board-2.json to generate it.
>
> pcie2 (nvme) is intentionally specified as max-link-speed = <16>. The
> interface is capable of it, most current nvme ssds are capable of it,
> but the physical slot isn't. This leads to a silent downgrade to <8> instead
> of the "device is limited by bus, capable of..." message.
>
> It is in use and under development since May 2023, pretty stable now.
>
> ---
> Changes in v4:
> - removed the redundant regulator definitions
> - changed the pinctrl property order
> - use microsoft instead of MICROSOFT as subdirectory and device name component
> - amend spacing in audio nodes
> - change external connector dp1 for mini-dp to DP-3 for consistency
> - Link to v3: https://lore.kernel.org/r/20241013-jg-blackrock-for-upstream-v3-0-839d3483a8e7@oldschoolsolutions.biz
>
> Changes in v3:
> - tried to heed all advice and comments given - thank you
> - re-ordered patches to definition before use
> - added "microsoft,blackrock" as compatible in QSEECOM driver
> - removed the qseecom node
> - ordered nodes alphabetically {address, node name, label}
> - amended indentation
> - consistently used blackrock as identifier / directory name
> - sorted identifiers by the same order for multiple instances
> - added some explanation re WiFi
> - added definition for PMU on the WCN6855
> - added some explanation for pcie2 max-link-speed
> - Link to v2: https://lore.kernel.org/r/20240920-jg-blackrock-for-upstream-v2-0-9bf2f1b2191c@oldschoolsolutions.biz
>
> Changes in v2:
> - removed whitespaces and breaks
> - added compatibility binding
> - added feature list
> - reformatted Signed-off list
> - Link to v1: https://lore.kernel.org/r/5f5487e1-e458-4a3a-af02-c52e50ca1964@oldschoolsolutions.biz
>
> ---
> Jens Glathe (3):
> dt-bindings: arm: qcom: Add Microsoft Windows Dev Kit 2023
> firmware: qcom: scm: Allow QSEECOM for Windows Dev Kit 2023
> arm64: dts: qcom: sc8280xp-blackrock: dt definition for WDK2023
>
> Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../boot/dts/qcom/sc8280xp-microsoft-blackrock.dts | 1383 ++++++++++++++++++++
> drivers/firmware/qcom/qcom_scm.c | 1 +
> 4 files changed, 1386 insertions(+)
> ---
> base-commit: a39230ecf6b3057f5897bc4744a790070cfbe7a8
> change-id: 20240920-jg-blackrock-for-upstream-7c7aca20e832
>
> Best regards,
> --
> Jens Glathe <jens.glathe@oldschoolsolutions.biz>
>
>
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y qcom/sc8280xp-microsoft-blackrock.dtb' for 20241027-jg-blackrock-for-upstream-v4-0-703b254fc95f@oldschoolsolutions.biz:
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: pcie@1c00000: Unevaluated properties are not allowed ('vdda-supply' was unexpected)
from schema $id: http://devicetree.org/schemas/pci/qcom,pcie-sc8280xp.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: pcie@1c20000: max-link-speed: 16 is not one of [1, 2, 3, 4]
from schema $id: http://devicetree.org/schemas/pci/qcom,pcie-sc8280xp.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: pcie@1c20000: Unevaluated properties are not allowed ('#address-cells', '#interrupt-cells', '#size-cells', 'aspm-no-l0s', 'bus-range', 'device_type', 'dma-coherent', 'interconnect-names', 'interconnects', 'interrupt-map', 'interrupt-map-mask', 'linux,pci-domain', 'max-link-speed', 'msi-map', 'num-lanes', 'pcie@0', 'perst-gpios', 'phy-names', 'phys', 'power-domains', 'ranges', 'required-opps', 'vdda-supply', 'vddpe-3v3-supply', 'wake-gpios' were unexpected)
from schema $id: http://devicetree.org/schemas/pci/qcom,pcie-sc8280xp.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: pcie@1c20000: max-link-speed: 16 is not one of [1, 2, 3, 4]
from schema $id: http://devicetree.org/schemas/pci/pci-bus-common.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: phy@88e5000: 'vdda-phy-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/phy/qcom,usb-snps-femto-v2.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: phy@88e7000: 'vdda-phy-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/phy/qcom,usb-snps-femto-v2.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: phy@88e8000: 'vdda-phy-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/phy/qcom,usb-snps-femto-v2.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: phy@88e9000: 'vdda-phy-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/phy/qcom,usb-snps-femto-v2.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: phy@88ea000: 'vdda-phy-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/phy/qcom,usb-snps-femto-v2.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: phy@8902000: 'vdda-phy-supply' does not match any of the regexes: 'pinctrl-[0-9]+'
from schema $id: http://devicetree.org/schemas/phy/qcom,usb-snps-femto-v2.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: usb@a4f8800: usb@a400000:phy-names: 'oneOf' conditional failed, one must be fixed:
'usb2-port0' is not one of ['usb2-phy', 'usb3-phy']
'usb2-port0' does not match '^usb(2-([0-9]|1[0-4])|3-[0-3])$'
'usb3-port0' is not one of ['usb2-phy', 'usb3-phy']
'usb3-port0' does not match '^usb(2-([0-9]|1[0-4])|3-[0-3])$'
from schema $id: http://devicetree.org/schemas/usb/qcom,dwc3.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: usb@a400000: phy-names: 'oneOf' conditional failed, one must be fixed:
'usb2-port0' is not one of ['usb2-phy', 'usb3-phy']
'usb2-port0' does not match '^usb(2-([0-9]|1[0-4])|3-[0-3])$'
'usb3-port0' is not one of ['usb2-phy', 'usb3-phy']
'usb3-port0' does not match '^usb(2-([0-9]|1[0-4])|3-[0-3])$'
from schema $id: http://devicetree.org/schemas/usb/snps,dwc3.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: wcn6855-pmu: 'vddpmumx-supply' is a required property
from schema $id: http://devicetree.org/schemas/regulator/qcom,qca6390-pmu.yaml#
arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dtb: wcn6855-pmu: 'vddpmucx-supply' is a required property
from schema $id: http://devicetree.org/schemas/regulator/qcom,qca6390-pmu.yaml#
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: [PATCH v4 3/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for WDK2023
2024-10-27 13:02 ` [PATCH v4 3/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for WDK2023 Jens Glathe via B4 Relay
@ 2024-10-29 20:18 ` Bjorn Andersson
0 siblings, 0 replies; 8+ messages in thread
From: Bjorn Andersson @ 2024-10-29 20:18 UTC (permalink / raw)
To: jens.glathe
Cc: Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
linux-arm-msm, devicetree, linux-kernel, Merck Hung
On Sun, Oct 27, 2024 at 02:02:18PM GMT, Jens Glathe via B4 Relay wrote:
> From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
>
> Device tree for the Microsoft Windows Dev Kit 2023. This work
> is based on the initial work of Merck Hung <merckhung@gmail.com>.
>
> The Windows Dev Kit 2023 is a nice little desktop based on sc8280xp.
> Link: https://learn.microsoft.com/en-us/windows/arm/dev-kit/
>
> Supported features:
> - USB type-c and type-a ports
> - minidp connector
> - built-in r8152 Ethernet adapter
> - PCIe devices
> - nvme
> - ath11k WiFi (WCN6855)
> - WCN6855 Bluetooth
> - A690 GPU
> - ADSP and CDSP
> - GPIO keys
> - Audio definition (works via USB)
>
> Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
> Signed-off-by: Merck Hung <merckhung@gmail.com>
Is this Co-developed-by, or is it simply "Based on initial work by Merck
Hung"?
If the latter, I'd suggest drop Merck's s-o-b, give credit to Merck in a
written comment and rely on "Developer's certificate of origin" option b.
Regards,
Bjorn
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../boot/dts/qcom/sc8280xp-microsoft-blackrock.dts | 1383 ++++++++++++++++++++
> 2 files changed, 1384 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index ac199f809b0d4..0e354299f832b 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -192,6 +192,7 @@ dtb-$(CONFIG_ARCH_QCOM) += sc8180x-primus.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-crd.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-lenovo-thinkpad-x13s.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-microsoft-arcata.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += sc8280xp-microsoft-blackrock.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sda660-inforce-ifc6560.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm450-lenovo-tbx605f.dtb
> dtb-$(CONFIG_ARCH_QCOM) += sdm450-motorola-ali.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dts b/arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dts
> new file mode 100644
> index 0000000000000..19ce7bb12c2e1
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sc8280xp-microsoft-blackrock.dts
> @@ -0,0 +1,1383 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, The Linux Foundation. All rights reserved.
> + * Copyright (c) 2022, Linaro Limited
> + * Copyright (c) 2023, Merck Hung <merckhung@gmail.com>
> + * Copyright (c) 2023, 2024 Jens Glathe <jens.glathe@oldschoolsolutions.biz>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/gpio-keys.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +
> +#include "sc8280xp.dtsi"
> +#include "sc8280xp-pmics.dtsi"
> +
> +/ {
> + model = "Windows Dev Kit 2023";
> + compatible = "microsoft,blackrock", "qcom,sc8280xp";
> + chassis-type = "desktop";
> +
> + aliases {
> + i2c4 = &i2c4;
> + i2c21 = &i2c21;
> + serial1 = &uart2;
> + };
> +
> + wcd938x: audio-codec {
> + compatible = "qcom,wcd9380-codec";
> +
> + pinctrl-0 = <&wcd_default>;
> + pinctrl-names = "default";
> +
> + reset-gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
> +
> + vdd-buck-supply = <&vreg_s10b>;
> + vdd-rxtx-supply = <&vreg_s10b>;
> + vdd-io-supply = <&vreg_s10b>;
> + vdd-mic-bias-supply = <&vreg_bob>;
> +
> + qcom,micbias1-microvolt = <1800000>;
> + qcom,micbias2-microvolt = <1800000>;
> + qcom,micbias3-microvolt = <1800000>;
> + qcom,micbias4-microvolt = <1800000>;
> + qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
> + qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
> + qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
> + qcom,rx-device = <&wcd_rx>;
> + qcom,tx-device = <&wcd_tx>;
> +
> + #sound-dai-cells = <1>;
> + };
> +
> + dp3_connector: connector {
> + compatible = "dp-connector";
> + label = "DP-3";
> + type = "mini";
> +
> + dp-pwr-supply = <&vreg_misc_3p3>;
> +
> + port {
> + dp1_connector_in: endpoint {
> + remote-endpoint = <&mdss0_dp2_phy_out>;
> + };
> + };
> + };
> +
> + pmic-glink {
> + compatible = "qcom,sc8280xp-pmic-glink", "qcom,pmic-glink";
> +
> + #address-cells = <1>;
> + #size-cells = <0>;
> + orientation-gpios = <&tlmm 166 GPIO_ACTIVE_HIGH>,
> + <&tlmm 49 GPIO_ACTIVE_HIGH>;
> +
> + /* Left-side rear port */
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "source";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_con0_hs: endpoint {
> + remote-endpoint = <&usb_0_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_con0_ss: endpoint {
> + remote-endpoint = <&usb_0_qmpphy_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> +
> + pmic_glink_con0_sbu: endpoint {
> + remote-endpoint = <&usb0_sbu_mux>;
> + };
> + };
> + };
> + };
> +
> + /* Left-side front port */
> + connector@1 {
> + compatible = "usb-c-connector";
> + reg = <1>;
> + power-role = "source";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_con1_hs: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_con1_ss: endpoint {
> + remote-endpoint = <&usb_1_qmpphy_out>;
> + };
> + };
> +
> + port@2 {
> + reg = <2>;
> +
> + pmic_glink_con1_sbu: endpoint {
> + remote-endpoint = <&usb1_sbu_mux>;
> + };
> + };
> + };
> + };
> + };
> +
> + vreg_misc_3p3: regulator-misc-3p3 {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "VCC3B";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&pmc8280_1_gpios 1 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-0 = <&misc_3p3_reg_en>;
> + pinctrl-names = "default";
> +
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vreg_nvme: regulator-nvme {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "VCC3_SSD";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&tlmm 135 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-0 = <&nvme_reg_en>;
> + pinctrl-names = "default";
> +
> + regulator-boot-on;
> + };
> +
> + vreg_vph_pwr: regulator-vph-pwr {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "VPH_VCC3R9";
> + regulator-min-microvolt = <3900000>;
> + regulator-max-microvolt = <3900000>;
> +
> + regulator-always-on;
> + };
> +
> + vreg_wlan: regulator-wlan {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "VCC_WLAN_3R9";
> + regulator-min-microvolt = <3900000>;
> + regulator-max-microvolt = <3900000>;
> +
> + gpio = <&pmr735a_gpios 1 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-0 = <&hastings_reg_en>;
> + pinctrl-names = "default";
> +
> + regulator-boot-on;
> + };
> +
> + vreg_wwan: regulator-wwan {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "VCC3B_WAN";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&pmc8280_2_gpios 1 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-0 = <&wwan_sw_en>;
> + pinctrl-names = "default";
> +
> + regulator-boot-on;
> + };
> +
> + reserved-memory {
> + gpu_mem: gpu-mem@8bf00000 {
> + reg = <0 0x8bf00000 0 0x2000>;
> + no-map;
> + };
> +
> + linux,cma {
> + compatible = "shared-dma-pool";
> + size = <0x0 0x8000000>;
> + reusable;
> + linux,cma-default;
> + };
> + };
> +
> + usb0-sbu-mux {
> + compatible = "pericom,pi3usb102", "gpio-sbu-mux";
> +
> + enable-gpios = <&tlmm 101 GPIO_ACTIVE_LOW>;
> + select-gpios = <&tlmm 164 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-0 = <&usb0_sbu_default>;
> + pinctrl-names = "default";
> +
> + mode-switch;
> + orientation-switch;
> +
> + port {
> + usb0_sbu_mux: endpoint {
> + remote-endpoint = <&pmic_glink_con0_sbu>;
> + };
> + };
> + };
> +
> + usb1-sbu-mux {
> + compatible = "pericom,pi3usb102", "gpio-sbu-mux";
> +
> + enable-gpios = <&tlmm 48 GPIO_ACTIVE_LOW>;
> + select-gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
> +
> + pinctrl-0 = <&usb1_sbu_default>;
> + pinctrl-names = "default";
> +
> + mode-switch;
> + orientation-switch;
> +
> + port {
> + usb1_sbu_mux: endpoint {
> + remote-endpoint = <&pmic_glink_con1_sbu>;
> + };
> + };
> + };
> +
> + wcn6855-pmu {
> + compatible = "qcom,wcn6855-pmu";
> +
> + pinctrl-0 = <&bt_default>, <&wlan_en>;
> + pinctrl-names = "default";
> +
> + wlan-enable-gpios = <&tlmm 134 GPIO_ACTIVE_HIGH>;
> + bt-enable-gpios = <&tlmm 133 GPIO_ACTIVE_HIGH>;
> +
> + vddio-supply = <&vreg_s10b>;
> + vddaon-supply = <&vreg_s12b>;
> + vddpmu-supply = <&vreg_s12b>;
> + vddrfa0p95-supply = <&vreg_s12b>;
> + vddrfa1p3-supply = <&vreg_s11b>;
> + vddrfa1p9-supply = <&vreg_s1c>;
> + vddpcie1p3-supply = <&vreg_s11b>;
> + vddpcie1p9-supply = <&vreg_s1c>;
> +
> + regulators {
> + vreg_pmu_rfa_cmn_0p8: ldo0 {
> + regulator-name = "vreg_pmu_rfa_cmn_0p8";
> + };
> +
> + vreg_pmu_aon_0p8: ldo1 {
> + regulator-name = "vreg_pmu_aon_0p8";
> + };
> +
> + vreg_pmu_wlcx_0p8: ldo2 {
> + regulator-name = "vreg_pmu_wlcx_0p8";
> + };
> +
> + vreg_pmu_wlmx_0p8: ldo3 {
> + regulator-name = "vreg_pmu_wlmx_0p8";
> + };
> +
> + vreg_pmu_btcmx_0p8: ldo4 {
> + regulator-name = "vreg_pmu_btcmx_0p8";
> + };
> +
> + vreg_pmu_pcie_1p8: ldo5 {
> + regulator-name = "vreg_pmu_pcie_1p8";
> + };
> +
> + vreg_pmu_pcie_0p9: ldo6 {
> + regulator-name = "vreg_pmu_pcie_0p9";
> + };
> +
> + vreg_pmu_rfa_0p8: ldo7 {
> + regulator-name = "vreg_pmu_rfa_0p8";
> + };
> +
> + vreg_pmu_rfa_1p2: ldo8 {
> + regulator-name = "vreg_pmu_rfa_1p2";
> + };
> +
> + vreg_pmu_rfa_1p7: ldo9 {
> + regulator-name = "vreg_pmu_rfa_1p7";
> + };
> + };
> + };
> +};
> +
> +&apps_rsc {
> + regulators-0 {
> + compatible = "qcom,pm8350-rpmh-regulators";
> + qcom,pmic-id = "b";
> +
> + vdd-s10-supply = <&vreg_vph_pwr>;
> + vdd-s11-supply = <&vreg_vph_pwr>;
> + vdd-s12-supply = <&vreg_vph_pwr>;
> + vdd-l1-l4-supply = <&vreg_s12b>;
> + vdd-l2-l7-supply = <&vreg_bob>;
> + vdd-l3-l5-supply = <&vreg_s11b>;
> + vdd-l6-l9-l10-supply = <&vreg_s12b>;
> + vdd-l8-supply = <&vreg_s12b>;
> +
> + vreg_s10b: smps10 {
> + regulator-name = "vreg_s10b";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-always-on;
> + };
> +
> + vreg_s11b: smps11 {
> + regulator-name = "vreg_s11b";
> + regulator-min-microvolt = <1272000>;
> + regulator-max-microvolt = <1272000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s12b: smps12 {
> + regulator-name = "vreg_s12b";
> + regulator-min-microvolt = <984000>;
> + regulator-max-microvolt = <984000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l1b: ldo1 {
> + regulator-name = "vreg_l1b";
> + regulator-min-microvolt = <912000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3b: ldo3 {
> + regulator-name = "vreg_l3b";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-boot-on;
> + };
> +
> + vreg_l4b: ldo4 {
> + regulator-name = "vreg_l4b";
> + regulator-min-microvolt = <912000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l6b: ldo6 {
> + regulator-name = "vreg_l6b";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-boot-on;
> + };
> + };
> +
> + regulators-1 {
> + compatible = "qcom,pm8350c-rpmh-regulators";
> + qcom,pmic-id = "c";
> +
> + vdd-bob-supply = <&vreg_vph_pwr>;
> + vdd-l1-l12-supply = <&vreg_s1c>;
> + vdd-l2-l8-supply = <&vreg_s1c>;
> + vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
> + vdd-l6-l9-l11-supply = <&vreg_bob>;
> + vdd-l10-supply = <&vreg_s11b>;
> +
> + vreg_s1c: smps1 {
> + regulator-name = "vreg_s1c";
> + regulator-min-microvolt = <1880000>;
> + regulator-max-microvolt = <1900000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-always-on;
> + };
> +
> + vreg_l1c: ldo1 {
> + regulator-name = "vreg_l1c";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l6c: ldo6 {
> + regulator-name = "vreg_l6c";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7c: ldo7 {
> + regulator-name = "vreg_l7c";
> + regulator-min-microvolt = <2504000>;
> + regulator-max-microvolt = <2504000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l8c: ldo8 {
> + regulator-name = "vreg_l8c";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l9c: ldo9 {
> + regulator-name = "vreg_l9c";
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <2960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l12c: ldo12 {
> + regulator-name = "vreg_l12c";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l13c: ldo13 {
> + regulator-name = "vreg_l13c";
> + regulator-min-microvolt = <3072000>;
> + regulator-max-microvolt = <3072000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_bob: bob {
> + regulator-name = "vreg_bob";
> + regulator-min-microvolt = <3008000>;
> + regulator-max-microvolt = <3960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
> + regulator-always-on;
> + };
> + };
> +
> + regulators-2 {
> + compatible = "qcom,pm8350-rpmh-regulators";
> + qcom,pmic-id = "d";
> +
> + vdd-l1-l4-supply = <&vreg_s11b>;
> + vdd-l2-l7-supply = <&vreg_bob>;
> + vdd-l3-l5-supply = <&vreg_s11b>;
> + vdd-l6-l9-l10-supply = <&vreg_s12b>;
> + vdd-l8-supply = <&vreg_s12b>;
> +
> + vreg_l2d: ldo2 {
> + regulator-name = "vreg_l2d";
> + regulator-min-microvolt = <3072000>;
> + regulator-max-microvolt = <3072000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3d: ldo3 {
> + regulator-name = "vreg_l3d";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l4d: ldo4 {
> + regulator-name = "vreg_l4d";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l6d: ldo6 {
> + regulator-name = "vreg_l6d";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7d: ldo7 {
> + regulator-name = "vreg_l7d";
> + regulator-min-microvolt = <3072000>;
> + regulator-max-microvolt = <3072000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l8d: ldo8 {
> + regulator-name = "vreg_l8d";
> + regulator-min-microvolt = <912000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l9d: ldo9 {
> + regulator-name = "vreg_l9d";
> + regulator-min-microvolt = <912000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l10d: ldo10 {
> + regulator-name = "vreg_l10d";
> + regulator-min-microvolt = <912000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +};
> +
> +&dispcc0 {
> + status = "okay";
> +};
> +
> +&gpu {
> + status = "okay";
> +
> + zap-shader {
> + memory-region = <&gpu_mem>;
> + firmware-name = "qcom/sc8280xp/microsoft/blackrock/qcdxkmsuc8280.mbn";
> + };
> +};
> +
> +&mdss0 {
> + status = "okay";
> +};
> +
> +&mdss0_dp0 {
> + status = "okay";
> +};
> +
> +&mdss0_dp0_out {
> + data-lanes = <0 1>;
> + remote-endpoint = <&usb_0_qmpphy_dp_in>;
> +};
> +
> +&mdss0_dp1 {
> + status = "okay";
> +};
> +
> +&mdss0_dp1_out {
> + data-lanes = <0 1>;
> + remote-endpoint = <&usb_1_qmpphy_dp_in>;
> +};
> +
> +&mdss0_dp2 {
> + compatible = "qcom,sc8280xp-dp";
> +
> + data-lanes = <0 1 2 3>;
> +
> + status = "okay";
> +
> + ports {
> + port@1 {
> + reg = <1>;
> + mdss0_dp2_phy_out: endpoint {
> + remote-endpoint = <&dp1_connector_in>;
> + };
> + };
> + };
> +};
> +
> +&mdss0_dp2_phy {
> + compatible = "qcom,sc8280xp-dp-phy";
> +
> + vdda-phy-supply = <&vreg_l3b>;
> + vdda-pll-supply = <&vreg_l6b>;
> +
> + status = "okay";
> +};
> +
> +&pcie2a {
> + aspm-no-l0s;
> + max-link-speed = <16>;
> +
> + perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
> +
> + vddpe-3v3-supply = <&vreg_nvme>;
> + vdda-supply = <&vreg_l7d>;
> +
> + pinctrl-0 = <&pcie2a_default>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +};
> +
> +&pcie2a_phy {
> + vdda-phy-supply = <&vreg_l4d>;
> + vdda-pll-supply = <&vreg_l6d>;
> +
> + status = "okay";
> +};
> +
> +&pcie4 {
> + aspm-no-l0s;
> + max-link-speed = <2>;
> +
> + perst-gpios = <&tlmm 141 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&tlmm 139 GPIO_ACTIVE_LOW>;
> +
> + vddpe-3v3-supply = <&vreg_wlan>;
> + vdda-supply = <&vreg_l7d>;
> +
> + pinctrl-0 = <&pcie4_default>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +};
> +
> +&pcie4_port0 {
> + wifi@0 {
> + compatible = "pci17cb,1103";
> + reg = <0x10000 0x0 0x0 0x0 0x0>;
> +
> + vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
> + vddaon-supply = <&vreg_pmu_aon_0p8>;
> + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> + vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
> + vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
> + vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
> + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
> + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
> + vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
> +
> + qcom,ath11k-calibration-variant = "volterra";
> + };
> +};
> +
> +&pcie4_phy {
> + vdda-phy-supply = <&vreg_l4d>;
> + vdda-pll-supply = <&vreg_l6d>;
> +
> + status = "okay";
> +};
> +
> +&pmc8280c_lpg {
> + status = "okay";
> +};
> +
> +&pmk8280_adc_tm {
> + status = "okay";
> +
> + sys-therm@0 {
> + reg = <0>;
> + io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,avg-samples = <2>;
> + qcom,ratiometric;
> + };
> +
> + sys-therm@1 {
> + reg = <1>;
> + io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,avg-samples = <2>;
> + qcom,ratiometric;
> + };
> +
> + sys-therm@2 {
> + reg = <2>;
> + io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,avg-samples = <2>;
> + qcom,ratiometric;
> + };
> +
> + sys-therm@3 {
> + reg = <3>;
> + io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,avg-samples = <2>;
> + qcom,ratiometric;
> + };
> +
> + sys-therm@4 {
> + reg = <4>;
> + io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM1_100K_PU(3)>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,avg-samples = <2>;
> + qcom,ratiometric;
> + };
> +
> + sys-therm@5 {
> + reg = <5>;
> + io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM2_100K_PU(3)>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,avg-samples = <2>;
> + qcom,ratiometric;
> + };
> +
> + sys-therm@6 {
> + reg = <6>;
> + io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM3_100K_PU(3)>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,avg-samples = <2>;
> + qcom,ratiometric;
> + };
> +
> + sys-therm@7 {
> + reg = <7>;
> + io-channels = <&pmk8280_vadc PM8350_ADC7_AMUX_THM4_100K_PU(3)>;
> + qcom,hw-settle-time-us = <200>;
> + qcom,avg-samples = <2>;
> + qcom,ratiometric;
> + };
> +};
> +
> +&pmk8280_pon_pwrkey {
> + status = "okay";
> +};
> +
> +&pmk8280_pon_resin {
> + status = "okay";
> +};
> +
> +&pmk8280_rtc {
> + nvmem-cells = <&rtc_offset>;
> + nvmem-cell-names = "offset";
> +
> + status = "okay";
> +};
> +
> +&pmk8280_sdam_6 {
> + status = "okay";
> +
> + rtc_offset: rtc-offset@bc {
> + reg = <0xbc 0x4>;
> + };
> +};
> +
> +&pmk8280_vadc {
> + channel@144 {
> + reg = <PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
> + qcom,hw-settle-time = <200>;
> + qcom,ratiometric;
> + label = "sys_therm1";
> + };
> +
> + channel@145 {
> + reg = <PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
> + qcom,hw-settle-time = <200>;
> + qcom,ratiometric;
> + label = "sys_therm2";
> + };
> +
> + channel@146 {
> + reg = <PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
> + qcom,hw-settle-time = <200>;
> + qcom,ratiometric;
> + label = "sys_therm3";
> + };
> +
> + channel@147 {
> + reg = <PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
> + qcom,hw-settle-time = <200>;
> + qcom,ratiometric;
> + label = "sys_therm4";
> + };
> +
> + channel@344 {
> + reg = <PM8350_ADC7_AMUX_THM1_100K_PU(3)>;
> + qcom,hw-settle-time = <200>;
> + qcom,ratiometric;
> + label = "sys_therm5";
> + };
> +
> + channel@345 {
> + reg = <PM8350_ADC7_AMUX_THM2_100K_PU(3)>;
> + qcom,hw-settle-time = <200>;
> + qcom,ratiometric;
> + label = "sys_therm6";
> + };
> +
> + channel@346 {
> + reg = <PM8350_ADC7_AMUX_THM3_100K_PU(3)>;
> + qcom,hw-settle-time = <200>;
> + qcom,ratiometric;
> + label = "sys_therm7";
> + };
> +
> + channel@347 {
> + reg = <PM8350_ADC7_AMUX_THM4_100K_PU(3)>;
> + qcom,hw-settle-time = <200>;
> + qcom,ratiometric;
> + label = "sys_therm8";
> + };
> +};
> +
> +&qup0 {
> + status = "okay";
> +};
> +
> +&qup1 {
> + status = "okay";
> +};
> +
> +&qup2 {
> + status = "okay";
> +};
> +
> +&remoteproc_adsp {
> + firmware-name = "qcom/sc8280xp/microsoft/blackrock/qcadsp8280.mbn";
> +
> + status = "okay";
> +};
> +
> +&remoteproc_nsp0 {
> + firmware-name = "qcom/sc8280xp/microsoft/blackrock/qccdsp8280.mbn";
> +
> + status = "okay";
> +};
> +
> +&rxmacro {
> + status = "okay";
> +};
> +
> +&sound {
> + compatible = "qcom,sc8280xp-sndcard";
> + model = "microsoft/blackrock";
> + audio-routing =
> + "SpkrLeft IN", "WSA_SPK1 OUT",
> + "SpkrRight IN", "WSA_SPK2 OUT",
> + "IN1_HPHL", "HPHL_OUT",
> + "IN2_HPHR", "HPHR_OUT",
> + "AMIC2", "MIC BIAS2",
> + "VA DMIC0", "MIC BIAS1",
> + "VA DMIC1", "MIC BIAS1",
> + "VA DMIC2", "MIC BIAS3",
> + "VA DMIC0", "VA MIC BIAS1",
> + "VA DMIC1", "VA MIC BIAS1",
> + "VA DMIC2", "VA MIC BIAS3",
> + "TX SWR_ADC1", "ADC2_OUTPUT";
> +
> + wcd-playback-dai-link {
> + link-name = "WCD Playback";
> +
> + cpu {
> + sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
> + };
> +
> + codec {
> + sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
> + };
> +
> + platform {
> + sound-dai = <&q6apm>;
> + };
> + };
> +
> + wcd-capture-dai-link {
> + link-name = "WCD Capture";
> +
> + cpu {
> + sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
> + };
> +
> + codec {
> + sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>;
> + };
> +
> + platform {
> + sound-dai = <&q6apm>;
> + };
> + };
> +
> + wsa-dai-link {
> + link-name = "WSA Playback";
> +
> + cpu {
> + sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
> + };
> +
> + codec {
> + sound-dai = <&swr0 0>, <&wsamacro 0>;
> + };
> +
> + platform {
> + sound-dai = <&q6apm>;
> + };
> + };
> +
> + va-dai-link {
> + link-name = "VA Capture";
> +
> + cpu {
> + sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
> + };
> +
> + platform {
> + sound-dai = <&q6apm>;
> + };
> +
> + codec {
> + sound-dai = <&vamacro 0>;
> + };
> + };
> +};
> +
> +&swr0 {
> + status = "okay";
> +};
> +
> +&swr1 {
> + status = "okay";
> +
> + wcd_rx: wcd9380-rx@0,4 {
> + compatible = "sdw20217010d00";
> + reg = <0 4>;
> + qcom,rx-port-mapping = <1 2 3 4 5>;
> + };
> +};
> +
> +&swr2 {
> + status = "okay";
> +
> + wcd_tx: wcd9380-tx@0,3 {
> + compatible = "sdw20217010d00";
> + reg = <0 3>;
> + qcom,tx-port-mapping = <1 1 2 3>;
> + };
> +};
> +
> +&txmacro {
> + status = "okay";
> +};
> +
> +&uart2 {
> + pinctrl-0 = <&uart2_default>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +
> + bluetooth {
> + compatible = "qcom,wcn6855-bt";
> +
> + vddrfacmn-supply = <&vreg_pmu_rfa_cmn_0p8>;
> + vddaon-supply = <&vreg_pmu_aon_0p8>;
> + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> + vddwlmx-supply = <&vreg_pmu_wlmx_0p8>;
> + vddbtcmx-supply = <&vreg_pmu_btcmx_0p8>;
> + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
> + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
> + vddrfa1p8-supply = <&vreg_pmu_rfa_1p7>;
> +
> + max-speed = <3200000>;
> + };
> +};
> +
> +&usb_0 {
> + status = "okay";
> +};
> +
> +&usb_0_dwc3 {
> + dr_mode = "host";
> +};
> +
> +&usb_0_dwc3_hs {
> + remote-endpoint = <&pmic_glink_con0_hs>;
> +};
> +
> +&usb_0_hsphy {
> + vdda-pll-supply = <&vreg_l9d>;
> + vdda-phy-supply = <&vreg_l4d>;
> + vdda18-supply = <&vreg_l1c>;
> + vdda33-supply = <&vreg_l7d>;
> +
> + status = "okay";
> +};
> +
> +&usb_0_qmpphy {
> + vdda-phy-supply = <&vreg_l4d>;
> + vdda-pll-supply = <&vreg_l9d>;
> +
> + orientation-switch;
> +
> + status = "okay";
> +};
> +
> +&usb_0_qmpphy_dp_in {
> + remote-endpoint = <&mdss0_dp0_out>;
> +};
> +
> +&usb_0_qmpphy_out {
> + remote-endpoint = <&pmic_glink_con0_ss>;
> +};
> +
> +&usb_1 {
> + status = "okay";
> +};
> +
> +&usb_1_dwc3 {
> + dr_mode = "host";
> +};
> +
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_con1_hs>;
> +};
> +
> +&usb_1_hsphy {
> + vdda-pll-supply = <&vreg_l4b>;
> + vdda-phy-supply = <&vreg_l3b>;
> + vdda18-supply = <&vreg_l1c>;
> + vdda33-supply = <&vreg_l13c>;
> +
> + status = "okay";
> +};
> +
> +&usb_1_qmpphy {
> + vdda-phy-supply = <&vreg_l3b>;
> + vdda-pll-supply = <&vreg_l4b>;
> +
> + orientation-switch;
> +
> + status = "okay";
> +};
> +
> +&usb_1_qmpphy_dp_in {
> + remote-endpoint = <&mdss0_dp1_out>;
> +};
> +
> +&usb_1_qmpphy_out {
> + remote-endpoint = <&pmic_glink_con1_ss>;
> +};
> +
> +&usb_2 {
> + pinctrl-0 = <&usb2_en_state>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +};
> +
> +&usb_2_dwc3 {
> + dr_mode = "host";
> + phy-names = "usb2-port0", "usb3-port0";
> + phys = <&usb_2_hsphy0>, <&usb_2_qmpphy0>;
> +
> + status = "okay";
> +};
> +
> +&usb_2_hsphy0 {
> + vdda-pll-supply = <&vreg_l1b>;
> + vdda-phy-supply = <&vreg_l3d>;
> + vdda18-supply = <&vreg_l1c>;
> + vdda33-supply = <&vreg_l7d>;
> +
> + status = "okay";
> +};
> +
> +&usb_2_hsphy1 {
> + vdda-pll-supply = <&vreg_l8d>;
> + vdda-phy-supply = <&vreg_l3d>;
> + vdda18-supply = <&vreg_l1c>;
> + vdda33-supply = <&vreg_l7d>;
> +
> + status = "okay";
> +};
> +
> +&usb_2_hsphy2 {
> + vdda-pll-supply = <&vreg_l10d>;
> + vdda-phy-supply = <&vreg_l3d>;
> + vdda18-supply = <&vreg_l8c>;
> + vdda33-supply = <&vreg_l2d>;
> +
> + status = "okay";
> +};
> +
> +&usb_2_hsphy3 {
> + vdda-pll-supply = <&vreg_l10d>;
> + vdda-phy-supply = <&vreg_l3d>;
> + vdda18-supply = <&vreg_l8c>;
> + vdda33-supply = <&vreg_l2d>;
> +
> + status = "okay";
> +};
> +
> +&usb_2_qmpphy0 {
> + vdda-phy-supply = <&vreg_l1b>;
> + vdda-pll-supply = <&vreg_l4d>;
> +
> + status = "okay";
> +};
> +
> +&usb_2_qmpphy1 {
> + vdda-phy-supply = <&vreg_l8d>;
> + vdda-pll-supply = <&vreg_l4d>;
> +
> + status = "okay";
> +};
> +
> +&vamacro {
> + pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
> + pinctrl-names = "default";
> +
> + vdd-micb-supply = <&vreg_s10b>;
> +
> + qcom,dmic-sample-rate = <4800000>;
> +
> + status = "okay";
> +};
> +
> +&wsamacro {
> + status = "okay";
> +};
> +
> +&xo_board_clk {
> + clock-frequency = <38400000>;
> +};
> +
> +/* PINCTRL */
> +
> +&lpass_tlmm {
> + status = "okay";
> +};
> +
> +&pmc8280_1_gpios {
> + edp_bl_en: edp-bl-en-state {
> + pins = "gpio8";
> + function = "normal";
> + };
> +
> + edp_bl_reg_en: edp-bl-reg-en-state {
> + pins = "gpio9";
> + function = "normal";
> + };
> +
> + misc_3p3_reg_en: misc-3p3-reg-en-state {
> + pins = "gpio1";
> + function = "normal";
> + };
> +};
> +
> +&pmc8280_2_gpios {
> + wwan_sw_en: wwan-sw-en-state {
> + pins = "gpio1";
> + function = "normal";
> + };
> +};
> +
> +&pmc8280c_gpios {
> + edp_bl_pwm: edp-bl-pwm-state {
> + pins = "gpio8";
> + function = "func1";
> + };
> +};
> +
> +&pmr735a_gpios {
> + hastings_reg_en: hastings-reg-en-state {
> + pins = "gpio1";
> + function = "normal";
> + };
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <70 2>, <74 6>, <125 2>, <128 2>, <154 4>;
> +
> + bt_default: bt-default-state {
> + hstp-bt-en-pins {
> + pins = "gpio133";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + hstp-sw-ctrl-pins {
> + pins = "gpio132";
> + function = "gpio";
> + bias-pull-down;
> + };
> + };
> +
> + nvme_reg_en: nvme-reg-en-state {
> + pins = "gpio135";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + pcie2a_default: pcie2a-default-state {
> + clkreq-n-pins {
> + pins = "gpio142";
> + function = "pcie2a_clkreq";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + perst-n-pins {
> + pins = "gpio143";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + wake-n-pins {
> + pins = "gpio145";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> + };
> +
> + pcie3a_default: pcie3a-default-state {
> + clkreq-n-pins {
> + pins = "gpio150";
> + function = "pcie3a_clkreq";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + perst-n-pins {
> + pins = "gpio151";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + wake-n-pins {
> + pins = "gpio148";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> + };
> +
> + pcie4_default: pcie4-default-state {
> + clkreq-n-pins {
> + pins = "gpio140";
> + function = "pcie4_clkreq";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + perst-n-pins {
> + pins = "gpio141";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + wake-n-pins {
> + pins = "gpio139";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> + };
> +
> + uart2_default: uart2-default-state {
> + cts-pins {
> + pins = "gpio121";
> + function = "qup2";
> + bias-bus-hold;
> + };
> +
> + rts-pins {
> + pins = "gpio122";
> + function = "qup2";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + rx-pins {
> + pins = "gpio124";
> + function = "qup2";
> + bias-pull-up;
> + };
> +
> + tx-pins {
> + pins = "gpio123";
> + function = "qup2";
> + drive-strength = <2>;
> + bias-disable;
> + };
> + };
> +
> + usb0_sbu_default: usb0-sbu-state {
> + oe-n-pins {
> + pins = "gpio101";
> + function = "gpio";
> + bias-disable;
> + drive-strength = <16>;
> + output-high;
> + };
> +
> + sel-pins {
> + pins = "gpio164";
> + function = "gpio";
> + bias-disable;
> + drive-strength = <16>;
> + };
> + };
> +
> + usb1_sbu_default: usb1-sbu-state {
> + oe-n-pins {
> + pins = "gpio48";
> + function = "gpio";
> + bias-disable;
> + drive-strength = <16>;
> + output-high;
> + };
> +
> + sel-pins {
> + pins = "gpio47";
> + function = "gpio";
> + bias-disable;
> + drive-strength = <16>;
> + };
> + };
> +
> + usb2_en_state: usb2-en-state {
> + /* TS3USB221A USB2.0 mux select */
> + pins = "gpio24";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + output-low;
> + };
> +
> + wcd_default: wcd-default-state {
> + reset-pins {
> + pins = "gpio106";
> + function = "gpio";
> + bias-disable;
> + };
> + };
> +
> + wlan_en: wlan-en-state {
> + pins = "gpio134";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> +};
>
> --
> 2.43.0
>
>
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2024-10-29 20:18 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2024-10-27 13:02 [PATCH v4 0/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for Windows Dev Kit 2023 Jens Glathe via B4 Relay
2024-10-27 13:02 ` [PATCH v4 1/3] dt-bindings: arm: qcom: Add Microsoft " Jens Glathe via B4 Relay
2024-10-27 20:19 ` Krzysztof Kozlowski
2024-10-27 20:20 ` Krzysztof Kozlowski
2024-10-27 13:02 ` [PATCH v4 2/3] firmware: qcom: scm: Allow QSEECOM for " Jens Glathe via B4 Relay
2024-10-27 13:02 ` [PATCH v4 3/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for WDK2023 Jens Glathe via B4 Relay
2024-10-29 20:18 ` Bjorn Andersson
2024-10-29 12:44 ` [PATCH v4 0/3] arm64: dts: qcom: sc8280xp-blackrock: dt definition for Windows Dev Kit 2023 Rob Herring (Arm)
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox