[PATCH v5 0/2] spi-geni-qcom: Add SPI device mode support for GENI based QuPv3

[PATCH v5 0/2] spi-geni-qcom: Add SPI device mode support for GENI based QuPv3

[Praveen Talari]

This series adds spi device mode functionality to geni based Qupv3.
The common header file contains spi slave related registers and masks.

Praveen Talari (2):
  soc: qcom: geni-se: Add SPI Device mode support for GENI based QuPv3
  spi: spi-geni-qcom: Add SPI Device mode support for GENI based QuPv3
---
v4 -> v5:
- Addressed review comments in driver

v3 -> v4:
- Used existing property spi-slave
- Hence dropped dt-binding changes

v2 -> v3:
- Modified commit message
- Addressed comment on dt-binding

v1 -> v2:
- Added dt-binding change for spi slave
- Modified commit message
- Addressed review comments in driver

 drivers/spi/spi-geni-qcom.c      | 53 ++++++++++++++++++++++++++++----
 include/linux/soc/qcom/geni-se.h |  9 ++++++
 2 files changed, 56 insertions(+), 6 deletions(-)

-- 
2.17.1

[PATCH v5 1/2] soc: qcom: geni-se: Add SPI Device mode support for GENI based QuPv3

[Praveen Talari]

Add device mode supported registers and masks.

Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
---
v2 -> v3:
- modified commit message to use device mode instead of slave mode

v1 -> v2:
- modified commit message
---
 include/linux/soc/qcom/geni-se.h | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/include/linux/soc/qcom/geni-se.h b/include/linux/soc/qcom/geni-se.h
index 821a19135bb6..29e06905bc1f 100644
--- a/include/linux/soc/qcom/geni-se.h
+++ b/include/linux/soc/qcom/geni-se.h
@@ -35,6 +35,7 @@ enum geni_se_protocol_type {
 	GENI_SE_UART,
 	GENI_SE_I2C,
 	GENI_SE_I3C,
+	GENI_SE_SPI_SLAVE,
 };
 
 struct geni_wrapper;
@@ -73,12 +74,14 @@ struct geni_se {
 
 /* Common SE registers */
 #define GENI_FORCE_DEFAULT_REG		0x20
+#define GENI_OUTPUT_CTRL		0x24
 #define SE_GENI_STATUS			0x40
 #define GENI_SER_M_CLK_CFG		0x48
 #define GENI_SER_S_CLK_CFG		0x4c
 #define GENI_IF_DISABLE_RO		0x64
 #define GENI_FW_REVISION_RO		0x68
 #define SE_GENI_CLK_SEL			0x7c
+#define SE_GENI_CFG_SEQ_START		0x84
 #define SE_GENI_DMA_MODE_EN		0x258
 #define SE_GENI_M_CMD0			0x600
 #define SE_GENI_M_CMD_CTRL_REG		0x604
@@ -111,6 +114,9 @@ struct geni_se {
 /* GENI_FORCE_DEFAULT_REG fields */
 #define FORCE_DEFAULT	BIT(0)
 
+/* GENI_OUTPUT_CTRL fields */
+#define GENI_IO_MUX_0_EN		BIT(0)
+
 /* GENI_STATUS fields */
 #define M_GENI_CMD_ACTIVE		BIT(0)
 #define S_GENI_CMD_ACTIVE		BIT(12)
@@ -130,6 +136,9 @@ struct geni_se {
 /* GENI_CLK_SEL fields */
 #define CLK_SEL_MSK			GENMASK(2, 0)
 
+/* SE_GENI_CFG_SEQ_START fields */
+#define START_TRIGGER			BIT(0)
+
 /* SE_GENI_DMA_MODE_EN */
 #define GENI_DMA_MODE_EN		BIT(0)
 
-- 
2.17.1

[PATCH v5 2/2] spi: spi-geni-qcom: Add SPI Device mode support for GENI based QuPv3

[Praveen Talari]

Currently spi geni driver supports only master mode operation.

Add spi device mode support to GENI based QuPv3.

Signed-off-by: Praveen Talari <quic_ptalari@quicinc.com>
---
v4 -> v5:
- added code comments
- dropped get_spi_master api.

v3 -> v4:
- Used existing property spi-slave.

v2 -> v3:
- modified commit message to use device mode instead of slave mode

v1 -> v2
- modified the commit message
- added the code changes for code comments
---
 drivers/spi/spi-geni-qcom.c | 53 ++++++++++++++++++++++++++++++++-----
 1 file changed, 47 insertions(+), 6 deletions(-)

diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c
index 206cc04bb1ed..06b114f3f21a 100644
--- a/drivers/spi/spi-geni-qcom.c
+++ b/drivers/spi/spi-geni-qcom.c
@@ -12,6 +12,7 @@
 #include <linux/platform_device.h>
 #include <linux/pm_opp.h>
 #include <linux/pm_runtime.h>
+#include <linux/property.h>
 #include <linux/soc/qcom/geni-se.h>
 #include <linux/spi/spi.h>
 #include <linux/spinlock.h>
@@ -52,6 +53,9 @@
 #define SPI_CS_CLK_DELAY_MSK		GENMASK(19, 10)
 #define SPI_CS_CLK_DELAY_SHFT		10
 
+#define SE_SPI_SLAVE_EN				(0x2BC)
+#define SPI_SLAVE_EN				BIT(0)
+
 /* M_CMD OP codes for SPI */
 #define SPI_TX_ONLY		1
 #define SPI_RX_ONLY		2
@@ -99,6 +103,16 @@ struct spi_geni_master {
 	int cur_xfer_mode;
 };
 
+static void spi_slv_setup(struct spi_geni_master *mas)
+{
+	struct geni_se *se = &mas->se;
+
+	writel(SPI_SLAVE_EN, se->base + SE_SPI_SLAVE_EN);
+	writel(GENI_IO_MUX_0_EN, se->base + GENI_OUTPUT_CTRL);
+	writel(START_TRIGGER, se->base + SE_GENI_CFG_SEQ_START);
+	dev_dbg(mas->dev, "spi slave setup done\n");
+}
+
 static int get_spi_clk_cfg(unsigned int speed_hz,
 			struct spi_geni_master *mas,
 			unsigned int *clk_idx,
@@ -140,12 +154,22 @@ static void handle_se_timeout(struct spi_master *spi,
 	const struct spi_transfer *xfer;
 
 	spin_lock_irq(&mas->lock);
-	reinit_completion(&mas->cancel_done);
 	if (mas->cur_xfer_mode == GENI_SE_FIFO)
 		writel(0, se->base + SE_GENI_TX_WATERMARK_REG);
 
 	xfer = mas->cur_xfer;
 	mas->cur_xfer = NULL;
+
+	if (spi->slave) {
+		/*
+		 * skip CMD Cancel sequnece since spi slave
+		 * doesn`t support CMD Cancel sequnece
+		 */
+		spin_unlock_irq(&mas->lock);
+		goto unmap_if_dma;
+	}
+
+	reinit_completion(&mas->cancel_done);
 	geni_se_cancel_m_cmd(se);
 	spin_unlock_irq(&mas->lock);
 
@@ -542,6 +566,10 @@ static bool geni_can_dma(struct spi_controller *ctlr,
 	if (mas->cur_xfer_mode == GENI_GPI_DMA)
 		return true;
 
+	/* Set SE DMA mode for SPI slave. */
+	if (ctlr->slave)
+		return true;
+
 	len = get_xfer_len_in_words(xfer, mas);
 	fifo_size = mas->tx_fifo_depth * mas->fifo_width_bits / mas->cur_bits_per_word;
 
@@ -619,6 +647,7 @@ static void spi_geni_release_dma_chan(struct spi_geni_master *mas)
 
 static int spi_geni_init(struct spi_geni_master *mas)
 {
+	struct spi_master *spi = dev_get_drvdata(mas->dev);
 	struct geni_se *se = &mas->se;
 	unsigned int proto, major, minor, ver;
 	u32 spi_tx_cfg, fifo_disable;
@@ -627,7 +656,14 @@ static int spi_geni_init(struct spi_geni_master *mas)
 	pm_runtime_get_sync(mas->dev);
 
 	proto = geni_se_read_proto(se);
-	if (proto != GENI_SE_SPI) {
+
+	if (spi->slave) {
+		if (proto != GENI_SE_SPI_SLAVE) {
+			dev_err(mas->dev, "Invalid proto %d\n", proto);
+			goto out_pm;
+		}
+		spi_slv_setup(mas);
+	} else if (proto != GENI_SE_SPI) {
 		dev_err(mas->dev, "Invalid proto %d\n", proto);
 		goto out_pm;
 	}
@@ -677,9 +713,11 @@ static int spi_geni_init(struct spi_geni_master *mas)
 	}
 
 	/* We always control CS manually */
-	spi_tx_cfg = readl(se->base + SE_SPI_TRANS_CFG);
-	spi_tx_cfg &= ~CS_TOGGLE;
-	writel(spi_tx_cfg, se->base + SE_SPI_TRANS_CFG);
+	if (!spi->slave) {
+		spi_tx_cfg = readl(se->base + SE_SPI_TRANS_CFG);
+		spi_tx_cfg &= ~CS_TOGGLE;
+		writel(spi_tx_cfg, se->base + SE_SPI_TRANS_CFG);
+	}
 
 out_pm:
 	pm_runtime_put(mas->dev);
@@ -1072,6 +1110,9 @@ static int spi_geni_probe(struct platform_device *pdev)
 	pm_runtime_set_autosuspend_delay(&pdev->dev, 250);
 	pm_runtime_enable(dev);
 
+	if (device_property_read_bool(&pdev->dev, "spi-slave"))
+		spi->slave = true;
+
 	ret = geni_icc_get(&mas->se, NULL);
 	if (ret)
 		goto spi_geni_probe_runtime_disable;
@@ -1092,7 +1133,7 @@ static int spi_geni_probe(struct platform_device *pdev)
 	 * for dma (gsi) mode, the gsi will set cs based on params passed in
 	 * TRE
 	 */
-	if (mas->cur_xfer_mode == GENI_SE_FIFO)
+	if (!spi->slave && mas->cur_xfer_mode == GENI_SE_FIFO)
 		spi->set_cs = spi_geni_set_cs;
 
 	ret = request_irq(mas->irq, geni_spi_isr, 0, dev_name(dev), spi);
-- 
2.17.1

Re: [PATCH v5 0/2] spi-geni-qcom: Add SPI device mode support for GENI based QuPv3

[Konrad Dybcio]

On 7.07.2023 07:16, Praveen Talari wrote:
> This series adds spi device mode functionality to geni based Qupv3.
> The common header file contains spi slave related registers and masks.
> 
> Praveen Talari (2):
>   soc: qcom: geni-se: Add SPI Device mode support for GENI based QuPv3
>   spi: spi-geni-qcom: Add SPI Device mode support for GENI based QuPv3
> ---
> v4 -> v5:
> - Addressed review comments in driver
"fix bug" says exactly nothing

Konrad
> 
> v3 -> v4:
> - Used existing property spi-slave
> - Hence dropped dt-binding changes
> 
> v2 -> v3:
> - Modified commit message
> - Addressed comment on dt-binding
> 
> v1 -> v2:
> - Added dt-binding change for spi slave
> - Modified commit message
> - Addressed review comments in driver
> 
>  drivers/spi/spi-geni-qcom.c      | 53 ++++++++++++++++++++++++++++----
>  include/linux/soc/qcom/geni-se.h |  9 ++++++
>  2 files changed, 56 insertions(+), 6 deletions(-)
> 

Re: [PATCH v5 0/2] spi-geni-qcom: Add SPI device mode support for GENI based QuPv3

[Praveen Talari]

Hi

On 7/7/2023 5:59 PM, Konrad Dybcio wrote:
> On 7.07.2023 07:16, Praveen Talari wrote:
>> This series adds spi device mode functionality to geni based Qupv3.
>> The common header file contains spi slave related registers and masks.
>>
>> Praveen Talari (2):
>>    soc: qcom: geni-se: Add SPI Device mode support for GENI based QuPv3
>>    spi: spi-geni-qcom: Add SPI Device mode support for GENI based QuPv3
>> ---
>> v4 -> v5:
>> - Addressed review comments in driver
> "fix bug" says exactly nothing
Addressed
>
> Konrad
>> v3 -> v4:
>> - Used existing property spi-slave
>> - Hence dropped dt-binding changes
>>
>> v2 -> v3:
>> - Modified commit message
>> - Addressed comment on dt-binding
>>
>> v1 -> v2:
>> - Added dt-binding change for spi slave
>> - Modified commit message
>> - Addressed review comments in driver
>>
>>   drivers/spi/spi-geni-qcom.c      | 53 ++++++++++++++++++++++++++++----
>>   include/linux/soc/qcom/geni-se.h |  9 ++++++
>>   2 files changed, 56 insertions(+), 6 deletions(-)
>>