Re: [Bluez-users] IOGear GBU301 and Kernel 2.4.20

[Marcel Holtmann <marcel@holtmann.org>]

Hi Tom,

> > why don't include the content of /proc/bus/usb/devices?
> > 
> Your wish is my command....
> 
> >>>>>
> T:  Bus=03 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  5 Spd=12  MxCh= 0
> D:  Ver= 1.01 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
> P:  Vendor=0a5c ProdID=2033 Rev= 0.a0
> C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr=100mA
> I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
> E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
> E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
> E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
> I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
> E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
> I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
> E:  Ad=83(I) Atr=01(Isoc) MxPS=  16 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=  16 Ivl=1ms
> I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
> E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
> I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
> E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
> I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
> E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
> I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
> E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
> E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
> I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
> E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
> E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
> <<<<<
> 
> The above is just the part that is different between plugging in the IOGear
> adapter and not.  I didn't want to complicate things with too much clutter

this is a Broadcom BCM2033 dongle without firmware loaded. Install the
bluez-firmware package and use the bcm203x kernel driver from a recent
2.6 kernel or compile bluez-utils-2.9 with bcm203x support.

Regards

Marcel




-------------------------------------------------------
This SF.Net email is sponsored by OSTG. Have you noticed the changes on
Linux.com, ITManagersJournal and NewsForge in the past few weeks? Now,
one more big change to announce. We are now OSTG- Open Source Technology
Group. Come see the changes on the new OSTG site. www.ostg.com
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users