From: Jon Barnett <jbarnett@pobox.com>
To: BlueZ development <bluez-devel@lists.sourceforge.net>
Subject: Re: [Bluez-devel] Problems with Dell BCM2045 USB device
Date: Wed, 03 Jan 2007 15:04:21 -0500 [thread overview]
Message-ID: <1167854661.3145.4.camel@localhost> (raw)
In-Reply-To: <1167844461.20568.18.camel@violet>
[-- Attachment #1.1: Type: text/plain, Size: 11972 bytes --]
On Wed, 2007-01-03 at 18:14 +0100, Marcel Holtmann wrote:
> did you reload the driver or reboot your system? This would have been
> the first Broadcom chip where the values are correct. Can you
> check /sys/class/module/parameters/* that no quirk is actually active.
Oops, my bad! When I restored my original modprobe file it had my
initial force scofix quirk in it.
hci0: Type: USB
BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
DOWN
RX bytes:0 acl:0 sco:0 events:0 errors:0
TX bytes:0 acl:0 sco:0 commands:0 errors:0
The session dump is:
device: hci0 snap_len: 1028 filter: 0xffffffff
< HCI Command: Create Connection (0x01|0x0005) plen 13
bdaddr 00:12:EE:E0:AB:CA ptype 0xcc18 rswitch 0x01 clkoffset 0x0000
Packet type: DM1 DM3 DM5 DH1 DH3 DH5
> HCI Event: Command Status (0x0f) plen 4
Create Connection (0x01|0x0005) status 0x00 ncmd 1
> HCI Event: Connect Complete (0x03) plen 11
status 0x00 handle 12 bdaddr 00:12:EE:E0:AB:CA type ACL encrypt 0x00
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Connect req: psm 1 scid 0x0040
< HCI Command: Read Remote Supported Features (0x01|0x001b) plen 2
handle 12
> HCI Event: Command Status (0x0f) plen 4
Read Remote Supported Features (0x01|0x001b) status 0x00 ncmd 1
< HCI Command: Write Link Policy Settings (0x02|0x000d) plen 4
handle 12 policy 0x0f
Link policy: RSWITCH HOLD SNIFF PARK
> HCI Event: Read Remote Supported Features (0x0b) plen 11
status 0x00 handle 12
Features: 0xff 0xfd 0x29 0x78 0x18 0x18 0x00 0x80
> HCI Event: Command Complete (0x0e) plen 6
Write Link Policy Settings (0x02|0x000d) ncmd 1
status 0x00 handle 12
< HCI Command: Remote Name Request (0x01|0x0019) plen 10
bdaddr 00:12:EE:E0:AB:CA mode 2 clkoffset 0x0000
> HCI Event: Command Status (0x0f) plen 4
Remote Name Request (0x01|0x0019) status 0x00 ncmd 1
> HCI Event: Max Slots Change (0x1b) plen 3
handle 12 slots 5
> ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Connect rsp: dcid 0x0051 scid 0x0040 result 0 status 0
Connection successful
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Config req: dcid 0x0051 flags 0x00 clen 0
> ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Config req: dcid 0x0040 flags 0x00 clen 4
MTU 100
< ACL data: handle 12 flags 0x02 dlen 18
L2CAP(s): Config rsp: scid 0x0051 flags 0x00 result 0 clen 4
Success
MTU 100
> HCI Event: Remote Name Req Complete (0x07) plen 255
status 0x00 bdaddr 00:12:EE:E0:AB:CA name 'HBH-610a'
> ACL data: handle 12 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0040 flags 0x00 result 0 clen 0
Success
< ACL data: handle 12 flags 0x02 dlen 24
L2CAP(d): cid 0x0051 len 20 [psm 1]
SDP SSA Req: tid 0x0 len 0xf
pat uuid-16 0x1108 (Headset)
max 65535
aid(s) 0x0000 - 0xffff
cont 00
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 4
> ACL data: handle 12 flags 0x02 dlen 27
> ACL data: handle 12 flags 0x01 dlen 27
> ACL data: handle 12 flags 0x01 dlen 27
> ACL data: handle 12 flags 0x01 dlen 25
L2CAP(d): cid 0x0040 len 102 [psm 1]
SDP SSA Rsp: tid 0x0 len 0x61
count 94
record #0
aid 0x0000 (SrvRecHndl)
uint 0x10002
aid 0x0001 (SrvClassIDList)
< uuid-16 0x1108 (Headset) uuid-16 0x1203 (Audio) >
aid 0x0004 (ProtocolDescList)
< < uuid-16 0x0100 (L2CAP) > <
uuid-16 0x0003 (RFCOMM) uint 0x1 > >
aid 0x0009 (BTProfileDescList)
< < uuid-16 0x1108 (Headset) uint 0x100 > >
aid 0x0100 (SrvName)
str "SonyEricsson Headset Service"
aid 0x0302 (unknown)
bool 0x1
cont 00
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Disconn req: dcid 0x0051 scid 0x0040
< HCI Command: Read Voice Setting (0x03|0x0025) plen 0
> HCI Event: Command Complete (0x0e) plen 6
Read Voice Setting (0x03|0x0025) ncmd 1
status 0x00 voice setting 0x0060
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Connect req: psm 3 scid 0x0041
> ACL data: handle 12 flags 0x02 dlen 12
L2CAP(s): Disconn rsp: dcid 0x0051 scid 0x0040
> ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Connect rsp: dcid 0x0052 scid 0x0041 result 1 status 1
Connection pending - Authentication pending
> HCI Event: Link Key Request (0x17) plen 6
bdaddr 00:12:EE:E0:AB:CA
< HCI Command: Link Key Request Reply (0x01|0x000b) plen 22
bdaddr 00:12:EE:E0:AB:CA key FDA84C7E01635351CE60FF683AEDE32F
> HCI Event: Command Complete (0x0e) plen 10
Link Key Request Reply (0x01|0x000b) ncmd 1
status 0x00 bdaddr 00:12:EE:E0:AB:CA
> ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Connect rsp: dcid 0x0052 scid 0x0041 result 0 status 0
Connection successful
< ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Config req: dcid 0x0052 flags 0x00 clen 4
MTU 1013
> ACL data: handle 12 flags 0x02 dlen 16
L2CAP(s): Config req: dcid 0x0041 flags 0x00 clen 4
MTU 56
< ACL data: handle 12 flags 0x02 dlen 18
L2CAP(s): Config rsp: scid 0x0052 flags 0x00 result 0 clen 4
Success
MTU 56
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 4
> ACL data: handle 12 flags 0x02 dlen 14
L2CAP(s): Config rsp: scid 0x0041 flags 0x00 result 0 clen 0
Success
< ACL data: handle 12 flags 0x02 dlen 8
L2CAP(d): cid 0x0052 len 4 [psm 3]
RFCOMM(s): SABM: cr 1 dlci 0 pf 1 ilen 0 fcs 0x1c
> ACL data: handle 12 flags 0x02 dlen 8
L2CAP(d): cid 0x0041 len 4 [psm 3]
RFCOMM(s): UA: cr 1 dlci 0 pf 1 ilen 0 fcs 0xd7
< ACL data: handle 12 flags 0x02 dlen 18
L2CAP(d): cid 0x0052 len 14 [psm 3]
RFCOMM(s): PN CMD: cr 1 dlci 0 pf 0 ilen 10 fcs 0x70 mcc_len 8
dlci 2 frame_type 0 credit_flow 15 pri 7 ack_timer 0
frame_size 51 max_retrans 0 credits 7
> ACL data: handle 12 flags 0x02 dlen 19
L2CAP(d): cid 0x0041 len 15 [psm 3]
RFCOMM(s): PN RSP: cr 0 dlci 0 pf 0 ilen 10 fcs 0xaa mcc_len 8
dlci 2 frame_type 0 credit_flow 14 pri 0 ack_timer 0
frame_size 50 max_retrans 0 credits 0
< ACL data: handle 12 flags 0x02 dlen 8
L2CAP(d): cid 0x0052 len 4 [psm 3]
RFCOMM(s): SABM: cr 1 dlci 2 pf 1 ilen 0 fcs 0x59
> ACL data: handle 12 flags 0x02 dlen 8
L2CAP(d): cid 0x0041 len 4 [psm 3]
RFCOMM(s): UA: cr 1 dlci 2 pf 1 ilen 0 fcs 0x92
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(d): cid 0x0052 len 8 [psm 3]
RFCOMM(s): MSC CMD: cr 1 dlci 0 pf 0 ilen 4 fcs 0x70 mcc_len 2
dlci 2 fc 0 rtc 1 rtr 1 ic 0 dv 1 b1 0 b2 0 b3 0 len 0
> ACL data: handle 12 flags 0x02 dlen 13
L2CAP(d): cid 0x0041 len 9 [psm 3]
RFCOMM(s): MSC CMD: cr 0 dlci 0 pf 0 ilen 4 fcs 0xaa mcc_len 2
dlci 2 fc 0 rtc 1 rtr 1 ic 0 dv 0 b1 0 b2 0 b3 0 len 0
< ACL data: handle 12 flags 0x02 dlen 12
L2CAP(d): cid 0x0052 len 8 [psm 3]
RFCOMM(s): MSC RSP: cr 1 dlci 0 pf 0 ilen 4 fcs 0x70 mcc_len 2
dlci 2 fc 0 rtc 1 rtr 1 ic 0 dv 0 b1 0 b2 0 b3 0 len 0
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 4
> ACL data: handle 12 flags 0x02 dlen 13
L2CAP(d): cid 0x0041 len 9 [psm 3]
RFCOMM(s): MSC RSP: cr 0 dlci 0 pf 0 ilen 4 fcs 0xaa mcc_len 2
dlci 2 fc 0 rtc 1 rtr 1 ic 0 dv 1 b1 0 b2 0 b3 0 len 0
< ACL data: handle 12 flags 0x02 dlen 9
L2CAP(d): cid 0x0052 len 5 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 1 ilen 0 fcs 0x86 credits 33
> ACL data: handle 12 flags 0x02 dlen 20
L2CAP(d): cid 0x0041 len 16 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 1 ilen 10 fcs 0x5c credits 20
0000: 41 54 2a 45 43 42 50 3d 3f 0d AT*ECBP=?.
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> ACL data: handle 12 flags 0x02 dlen 19
L2CAP(d): cid 0x0041 len 15 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 0 ilen 10 fcs 0x40
0000: 41 54 2b 43 4c 49 50 3d 31 0d AT+CLIP=1.
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 4
> ACL data: handle 12 flags 0x02 dlen 26
L2CAP(d): cid 0x0041 len 22 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 1 ilen 16 fcs 0x5c credits 1
0000: 41 54 2b 43 53 43 53 3d 22 55 54 46 2d 38 22 0d AT
+CSCS="UTF-8".
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> ACL data: handle 12 flags 0x02 dlen 27
> ACL data: handle 12 flags 0x01 dlen 5
L2CAP(d): cid 0x0041 len 28 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 1 ilen 22 fcs 0x5c credits 1
0000: 41 54 2a 53 45 41 4d 3d 22 48 42 48 2d 36 31 30
AT*SEAM="HBH-610
0010: 61 22 2c 31 33 0d a",13.
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> ACL data: handle 12 flags 0x02 dlen 19
L2CAP(d): cid 0x0041 len 15 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 1 ilen 9 fcs 0x5c credits 1
0000: 41 54 2b 43 4c 41 4e 3f 0d AT+CLAN?.
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 3
> HCI Event: Max Slots Change (0x1b) plen 3
handle 12 slots 1
> HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 12 mode 0x02 interval 2048
Mode: Sniff
< HCI Command: Add SCO Connection (0x01|0x0007) plen 4
handle 12 ptype 0x00e0
Packet type: HV1 HV2 HV3
> HCI Event: Command Status (0x0f) plen 4
Add SCO Connection (0x01|0x0007) status 0x00 ncmd 1
> HCI Event: Connect Complete (0x03) plen 11
status 0x00 handle 1 bdaddr 00:12:EE:E0:AB:CA type SCO encrypt 0x00
< HCI Command: Remote Name Request (0x01|0x0019) plen 10
bdaddr 00:12:EE:E0:AB:CA mode 2 clkoffset 0x0000
> HCI Event: Command Status (0x0f) plen 4
Remote Name Request (0x01|0x0019) status 0x00 ncmd 1
> HCI Event: Remote Name Req Complete (0x07) plen 255
status 0x00 bdaddr 00:12:EE:E0:AB:CA name 'HBH-610a'
> ACL data: handle 12 flags 0x02 dlen 19
L2CAP(d): cid 0x0041 len 15 [psm 3]
RFCOMM(d): UIH: cr 0 dlci 2 pf 1 ilen 9 fcs 0x5c credits 2
0000: 41 54 2b 56 47 53 3d 36 0d AT+VGS=6.
< ACL data: handle 12 flags 0x02 dlen 14
L2CAP(d): cid 0x0052 len 10 [psm 3]
RFCOMM(d): UIH: cr 1 dlci 2 pf 0 ilen 6 fcs 0x9a
0000: 0d 0a 4f 4b 0d 0a ..OK..
> HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 12 mode 0x00 interval 0
Mode: Active
> HCI Event: Connection Packet Type Changed (0x1d) plen 5
status 0x00 handle 1 ptype 0x0080
Packet type: HV3
> HCI Event: Number of Completed Packets (0x13) plen 5
handle 12 packets 1
> HCI Event: Mode Change (0x14) plen 6
status 0x00 handle 12 mode 0x02 interval 2048
Mode: Sniff
Same end results with aplay hanging.
Cheers,
Jon.
[-- Attachment #1.2: This is a digitally signed message part --]
[-- Type: application/pgp-signature, Size: 189 bytes --]
[-- Attachment #2: Type: text/plain, Size: 347 bytes --]
-------------------------------------------------------------------------
Take Surveys. Earn Cash. Influence the Future of IT
Join SourceForge.net's Techsay panel and you'll get the chance to share your
opinions on IT & business topics through brief surveys - and earn cash
http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV
[-- Attachment #3: Type: text/plain, Size: 164 bytes --]
_______________________________________________
Bluez-devel mailing list
Bluez-devel@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-devel
next prev parent reply other threads:[~2007-01-03 20:04 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <mailman.341782.1167746753.8777.bluez-devel@lists.sourceforge.net>
2007-01-03 2:58 ` [Bluez-devel] Problems with Dell BCM2045 USB device Jon Barnett
2007-01-03 9:28 ` Marcel Holtmann
2007-01-03 17:05 ` Jon Barnett
2007-01-03 17:14 ` Marcel Holtmann
2007-01-03 20:04 ` Jon Barnett [this message]
2007-01-03 20:13 ` Marcel Holtmann
2007-01-03 21:56 ` Jon Barnett
2007-01-03 15:58 ` Brad Midgley
2007-01-08 20:14 ` Jon Barnett
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1167854661.3145.4.camel@localhost \
--to=jbarnett@pobox.com \
--cc=bluez-devel@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox