* Which software is responsible for bringing the devices (hci0 .. hcix) up ?
@ 2012-08-29 6:58 Vellemans, Noel
2012-08-29 7:08 ` Andrei Emeltchenko
0 siblings, 1 reply; 8+ messages in thread
From: Vellemans, Noel @ 2012-08-29 6:58 UTC (permalink / raw)
To: linux-bluetooth
Hi,
I have a simple question, I think, But I do not manage to find the
answer into the old mailing-list-posts.
I'm using bluez-4.99 and Linux kernel 2.6.35.3.
When plugging in a device (CSR-device) the device is recognized but it
is not 'UP'.
Can someone tell me what piece of software is NORMALLY setting the
device into the 'UP' state?
(so that I do not have to type hciconfig hci0 up)
# plug in the device ... results in ...
usb wakeup is here
usb 2-1: new full speed USB device using fsl-ehci and address 3
usb 2-1: New USB device found, idVendor=0a12, idProduct=0001
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
# hciconfig
hci0: Type: BR/EDR Bus: USB
BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
DOWN
RX bytes:0 acl:0 sco:0 events:0 errors:0
TX bytes:0 acl:0 sco:0 commands:0 errors:0
After manually executing hciconfig hci0 up the device is working fine.
# hciconfig hci0 up
# hciconfig
hci0: Type: BR/EDR Bus: USB
BD Address: 00:07:80:85:39:07 ACL MTU: 192:8 SCO MTU: 64:8
UP RUNNING
RX bytes:340 acl:0 sco:0 events:11 errors:0
TX bytes:38 acl:0 sco:0 commands:11 errors:0
Regards,
Noel
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Which software is responsible for bringing the devices (hci0 .. hcix) up ?
2012-08-29 6:58 Which software is responsible for bringing the devices (hci0 .. hcix) up ? Vellemans, Noel
@ 2012-08-29 7:08 ` Andrei Emeltchenko
2012-08-29 7:12 ` Vellemans, Noel
0 siblings, 1 reply; 8+ messages in thread
From: Andrei Emeltchenko @ 2012-08-29 7:08 UTC (permalink / raw)
To: Vellemans, Noel; +Cc: linux-bluetooth
Hi Noel,
On Wed, Aug 29, 2012 at 08:58:12AM +0200, Vellemans, Noel wrote:
> Hi,
>
>
> I have a simple question, I think, But I do not manage to find the
> answer into the old mailing-list-posts.
>
> I'm using bluez-4.99 and Linux kernel 2.6.35.3.
>
> When plugging in a device (CSR-device) the device is recognized but it
> is not 'UP'.
>
> Can someone tell me what piece of software is NORMALLY setting the
> device into the 'UP' state?
> (so that I do not have to type hciconfig hci0 up)
bluetoothd
Best regards
Andrei Emeltchenko
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Which software is responsible for bringing the devices (hci0 .. hcix) up ?
2012-08-29 7:08 ` Andrei Emeltchenko
@ 2012-08-29 7:12 ` Vellemans, Noel
2012-08-29 7:15 ` Andrei Emeltchenko
0 siblings, 1 reply; 8+ messages in thread
From: Vellemans, Noel @ 2012-08-29 7:12 UTC (permalink / raw)
To: Andrei Emeltchenko; +Cc: linux-bluetooth
Hi Andrei,
Any clue what the reason can be, that the device is not comming 'UP'
automatically ?
Regards Noel
-----Original Message-----
From: Andrei Emeltchenko [mailto:andrei.emeltchenko.news@gmail.com]
Sent: 29Aug12 09:09
To: Vellemans, Noel
Cc: linux-bluetooth@vger.kernel.org
Subject: Re: Which software is responsible for bringing the devices
(hci0 .. hcix) up ?
Hi Noel,
On Wed, Aug 29, 2012 at 08:58:12AM +0200, Vellemans, Noel wrote:
> Hi,
>
>
> I have a simple question, I think, But I do not manage to find the
> answer into the old mailing-list-posts.
>
> I'm using bluez-4.99 and Linux kernel 2.6.35.3.
>
> When plugging in a device (CSR-device) the device is recognized but it
> is not 'UP'.
>
> Can someone tell me what piece of software is NORMALLY setting the
> device into the 'UP' state?
> (so that I do not have to type hciconfig hci0 up)
bluetoothd
Best regards
Andrei Emeltchenko
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Which software is responsible for bringing the devices (hci0 .. hcix) up ?
2012-08-29 7:12 ` Vellemans, Noel
@ 2012-08-29 7:15 ` Andrei Emeltchenko
2012-08-29 7:20 ` Vellemans, Noel
0 siblings, 1 reply; 8+ messages in thread
From: Andrei Emeltchenko @ 2012-08-29 7:15 UTC (permalink / raw)
To: Vellemans, Noel; +Cc: linux-bluetooth
Hi Noel,
On Wed, Aug 29, 2012 at 09:12:18AM +0200, Vellemans, Noel wrote:
> Hi Andrei,
>
> Any clue what the reason can be, that the device is not comming 'UP'
> automatically ?
It is powered off automatically.
Best regards
Andrei Emeltchenko
>
>
> Regards Noel
>
>
> -----Original Message-----
> From: Andrei Emeltchenko [mailto:andrei.emeltchenko.news@gmail.com]
> Sent: 29Aug12 09:09
> To: Vellemans, Noel
> Cc: linux-bluetooth@vger.kernel.org
> Subject: Re: Which software is responsible for bringing the devices
> (hci0 .. hcix) up ?
>
> Hi Noel,
>
> On Wed, Aug 29, 2012 at 08:58:12AM +0200, Vellemans, Noel wrote:
> > Hi,
> >
> >
> > I have a simple question, I think, But I do not manage to find the
> > answer into the old mailing-list-posts.
> >
> > I'm using bluez-4.99 and Linux kernel 2.6.35.3.
> >
> > When plugging in a device (CSR-device) the device is recognized but it
>
> > is not 'UP'.
> >
> > Can someone tell me what piece of software is NORMALLY setting the
> > device into the 'UP' state?
> > (so that I do not have to type hciconfig hci0 up)
>
> bluetoothd
>
> Best regards
> Andrei Emeltchenko
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Which software is responsible for bringing the devices (hci0 .. hcix) up ?
2012-08-29 7:15 ` Andrei Emeltchenko
@ 2012-08-29 7:20 ` Vellemans, Noel
2012-08-29 7:37 ` Andrei Emeltchenko
0 siblings, 1 reply; 8+ messages in thread
From: Vellemans, Noel @ 2012-08-29 7:20 UTC (permalink / raw)
To: Andrei Emeltchenko; +Cc: linux-bluetooth
Hi,
It is an EXTERNAL USB-device plugged in manually, and if it is plugged
in, the device is recognized.
Regards Noel
<< log>>
Plug in device ... Results in....
# usb wakeup is here
usb 2-1: new full speed USB device using fsl-ehci and address 4
usb 2-1: New USB device found, idVendor=0a12, idProduct=0001
usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
#
# lsusb
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 0eef:7304 D-WAV Scientific Co., Ltd
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 004: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth
Dongle (HCI mode)
# hciconfig
hci0: Type: BR/EDR Bus: USB
BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
DOWN
RX bytes:0 acl:0 sco:0 events:0 errors:0
TX bytes:0 acl:0 sco:0 commands:0 errors:0
-----Original Message-----
From: Andrei Emeltchenko [mailto:andrei.emeltchenko.news@gmail.com]
Sent: 29Aug12 09:15
To: Vellemans, Noel
Cc: linux-bluetooth@vger.kernel.org
Subject: Re: Which software is responsible for bringing the devices
(hci0 .. hcix) up ?
Hi Noel,
On Wed, Aug 29, 2012 at 09:12:18AM +0200, Vellemans, Noel wrote:
> Hi Andrei,
>
> Any clue what the reason can be, that the device is not comming 'UP'
> automatically ?
It is powered off automatically.
Best regards
Andrei Emeltchenko
>
>
> Regards Noel
>
>
> -----Original Message-----
> From: Andrei Emeltchenko [mailto:andrei.emeltchenko.news@gmail.com]
> Sent: 29Aug12 09:09
> To: Vellemans, Noel
> Cc: linux-bluetooth@vger.kernel.org
> Subject: Re: Which software is responsible for bringing the devices
> (hci0 .. hcix) up ?
>
> Hi Noel,
>
> On Wed, Aug 29, 2012 at 08:58:12AM +0200, Vellemans, Noel wrote:
> > Hi,
> >
> >
> > I have a simple question, I think, But I do not manage to find the
> > answer into the old mailing-list-posts.
> >
> > I'm using bluez-4.99 and Linux kernel 2.6.35.3.
> >
> > When plugging in a device (CSR-device) the device is recognized but
> > it
>
> > is not 'UP'.
> >
> > Can someone tell me what piece of software is NORMALLY setting the
> > device into the 'UP' state?
> > (so that I do not have to type hciconfig hci0 up)
>
> bluetoothd
>
> Best regards
> Andrei Emeltchenko
>
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Which software is responsible for bringing the devices (hci0 .. hcix) up ?
2012-08-29 7:20 ` Vellemans, Noel
@ 2012-08-29 7:37 ` Andrei Emeltchenko
2012-08-29 7:49 ` Vellemans, Noel
0 siblings, 1 reply; 8+ messages in thread
From: Andrei Emeltchenko @ 2012-08-29 7:37 UTC (permalink / raw)
To: Vellemans, Noel; +Cc: linux-bluetooth
Hi,
On Wed, Aug 29, 2012 at 09:20:34AM +0200, Vellemans, Noel wrote:
> Hi,
>
> It is an EXTERNAL USB-device plugged in manually, and if it is plugged
> in, the device is recognized.
Do you have bluetoothd running?
Best regards
Andrei Emeltchenko
>
>
> Regards Noel
>
> << log>>
>
> Plug in device ... Results in....
>
>
> # usb wakeup is here
> usb 2-1: new full speed USB device using fsl-ehci and address 4
> usb 2-1: New USB device found, idVendor=0a12, idProduct=0001
> usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
>
> #
>
> # lsusb
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 001 Device 002: ID 0eef:7304 D-WAV Scientific Co., Ltd
> Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> Bus 002 Device 004: ID 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth
> Dongle (HCI mode)
>
>
> # hciconfig
> hci0: Type: BR/EDR Bus: USB
> BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
> DOWN
> RX bytes:0 acl:0 sco:0 events:0 errors:0
> TX bytes:0 acl:0 sco:0 commands:0 errors:0
>
>
> -----Original Message-----
> From: Andrei Emeltchenko [mailto:andrei.emeltchenko.news@gmail.com]
> Sent: 29Aug12 09:15
> To: Vellemans, Noel
> Cc: linux-bluetooth@vger.kernel.org
> Subject: Re: Which software is responsible for bringing the devices
> (hci0 .. hcix) up ?
>
> Hi Noel,
>
> On Wed, Aug 29, 2012 at 09:12:18AM +0200, Vellemans, Noel wrote:
> > Hi Andrei,
> >
> > Any clue what the reason can be, that the device is not comming 'UP'
> > automatically ?
>
> It is powered off automatically.
>
> Best regards
> Andrei Emeltchenko
>
> >
> >
> > Regards Noel
> >
> >
> > -----Original Message-----
> > From: Andrei Emeltchenko [mailto:andrei.emeltchenko.news@gmail.com]
> > Sent: 29Aug12 09:09
> > To: Vellemans, Noel
> > Cc: linux-bluetooth@vger.kernel.org
> > Subject: Re: Which software is responsible for bringing the devices
> > (hci0 .. hcix) up ?
> >
> > Hi Noel,
> >
> > On Wed, Aug 29, 2012 at 08:58:12AM +0200, Vellemans, Noel wrote:
> > > Hi,
> > >
> > >
> > > I have a simple question, I think, But I do not manage to find the
> > > answer into the old mailing-list-posts.
> > >
> > > I'm using bluez-4.99 and Linux kernel 2.6.35.3.
> > >
> > > When plugging in a device (CSR-device) the device is recognized but
> > > it
> >
> > > is not 'UP'.
> > >
> > > Can someone tell me what piece of software is NORMALLY setting the
> > > device into the 'UP' state?
> > > (so that I do not have to type hciconfig hci0 up)
> >
> > bluetoothd
> >
> > Best regards
> > Andrei Emeltchenko
> >
^ permalink raw reply [flat|nested] 8+ messages in thread
* RE: Which software is responsible for bringing the devices (hci0 .. hcix) up ?
2012-08-29 7:37 ` Andrei Emeltchenko
@ 2012-08-29 7:49 ` Vellemans, Noel
2012-08-29 10:58 ` Andrei Emeltchenko
0 siblings, 1 reply; 8+ messages in thread
From: Vellemans, Noel @ 2012-08-29 7:49 UTC (permalink / raw)
To: Andrei Emeltchenko; +Cc: linux-bluetooth
Hi,
>> Do you have bluetoothd running?
OK : You've got it.. I think.
When looking into the process-list with ps , I don't see bluetoothd.
When starting Bluetoothd on the command line .. . before plugging in the
device ..
the the device is 'UP' like it should be... (you are guiding/pointing me
in the GOOD direction, thankx)
Next question (Sorry) ? Isn't bluetoothd supposed to be launched by udev
?
Or I'm I missing some startup-script (/etc/init.d/... ) ?
I just wonder is there somewhere a description on how bleuz (bluetooth)
is started at boot ?
Regards Noel
-----Original Message-----
From: Andrei Emeltchenko [mailto:andrei.emeltchenko.news@gmail.com]
Sent: 29Aug12 09:38
To: Vellemans, Noel
Cc: linux-bluetooth@vger.kernel.org
Subject: Re: Which software is responsible for bringing the devices
(hci0 .. hcix) up ?
Hi,
On Wed, Aug 29, 2012 at 09:20:34AM +0200, Vellemans, Noel wrote:
> Hi,
>
> It is an EXTERNAL USB-device plugged in manually, and if it is plugged
> in, the device is recognized.
Do you have bluetoothd running?
Best regards
Andrei Emeltchenko
>
>
> Regards Noel
>
> << log>>
>
> Plug in device ... Results in....
>
>
> # usb wakeup is here
> usb 2-1: new full speed USB device using fsl-ehci and address 4 usb
> 2-1: New USB device found, idVendor=0a12, idProduct=0001 usb 2-1: New
> USB device strings: Mfr=0, Product=0, SerialNumber=0
>
> #
>
> # lsusb
> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 002
> Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 001 Device
> 002: ID 0eef:7304 D-WAV Scientific Co., Ltd Bus 003 Device 001: ID
> 1d6b:0002 Linux Foundation 2.0 root hub Bus 002 Device 004: ID
> 0a12:0001 Cambridge Silicon Radio, Ltd Bluetooth Dongle (HCI mode)
>
>
> # hciconfig
> hci0: Type: BR/EDR Bus: USB
> BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
> DOWN
> RX bytes:0 acl:0 sco:0 events:0 errors:0
> TX bytes:0 acl:0 sco:0 commands:0 errors:0
>
>
> -----Original Message-----
> From: Andrei Emeltchenko [mailto:andrei.emeltchenko.news@gmail.com]
> Sent: 29Aug12 09:15
> To: Vellemans, Noel
> Cc: linux-bluetooth@vger.kernel.org
> Subject: Re: Which software is responsible for bringing the devices
> (hci0 .. hcix) up ?
>
> Hi Noel,
>
> On Wed, Aug 29, 2012 at 09:12:18AM +0200, Vellemans, Noel wrote:
> > Hi Andrei,
> >
> > Any clue what the reason can be, that the device is not comming 'UP'
> > automatically ?
>
> It is powered off automatically.
>
> Best regards
> Andrei Emeltchenko
>
> >
> >
> > Regards Noel
> >
> >
> > -----Original Message-----
> > From: Andrei Emeltchenko [mailto:andrei.emeltchenko.news@gmail.com]
> > Sent: 29Aug12 09:09
> > To: Vellemans, Noel
> > Cc: linux-bluetooth@vger.kernel.org
> > Subject: Re: Which software is responsible for bringing the devices
> > (hci0 .. hcix) up ?
> >
> > Hi Noel,
> >
> > On Wed, Aug 29, 2012 at 08:58:12AM +0200, Vellemans, Noel wrote:
> > > Hi,
> > >
> > >
> > > I have a simple question, I think, But I do not manage to find the
> > > answer into the old mailing-list-posts.
> > >
> > > I'm using bluez-4.99 and Linux kernel 2.6.35.3.
> > >
> > > When plugging in a device (CSR-device) the device is recognized
> > > but it
> >
> > > is not 'UP'.
> > >
> > > Can someone tell me what piece of software is NORMALLY setting the
> > > device into the 'UP' state?
> > > (so that I do not have to type hciconfig hci0 up)
> >
> > bluetoothd
> >
> > Best regards
> > Andrei Emeltchenko
> >
^ permalink raw reply [flat|nested] 8+ messages in thread
* Re: Which software is responsible for bringing the devices (hci0 .. hcix) up ?
2012-08-29 7:49 ` Vellemans, Noel
@ 2012-08-29 10:58 ` Andrei Emeltchenko
0 siblings, 0 replies; 8+ messages in thread
From: Andrei Emeltchenko @ 2012-08-29 10:58 UTC (permalink / raw)
To: Vellemans, Noel; +Cc: linux-bluetooth
Hi,
On Wed, Aug 29, 2012 at 09:49:14AM +0200, Vellemans, Noel wrote:
> Hi,
>
> >> Do you have bluetoothd running?
>
> OK : You've got it.. I think.
>
> When looking into the process-list with ps , I don't see bluetoothd.
>
> When starting Bluetoothd on the command line .. . before plugging in the
> device ..
> the the device is 'UP' like it should be... (you are guiding/pointing me
> in the GOOD direction, thankx)
>
>
> Next question (Sorry) ? Isn't bluetoothd supposed to be launched by udev
> ?
>
> Or I'm I missing some startup-script (/etc/init.d/... ) ?
>
> I just wonder is there somewhere a description on how bleuz (bluetooth)
> is started at boot ?
This depends on your distro, I personally run it manually. I think you
need to enable it via some bluetooth-applet.
Best regards
Andrei Emeltchenko
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2012-08-29 10:58 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-08-29 6:58 Which software is responsible for bringing the devices (hci0 .. hcix) up ? Vellemans, Noel
2012-08-29 7:08 ` Andrei Emeltchenko
2012-08-29 7:12 ` Vellemans, Noel
2012-08-29 7:15 ` Andrei Emeltchenko
2012-08-29 7:20 ` Vellemans, Noel
2012-08-29 7:37 ` Andrei Emeltchenko
2012-08-29 7:49 ` Vellemans, Noel
2012-08-29 10:58 ` Andrei Emeltchenko
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox