* [PATCH v8 1/2] arm64: dts: qcom: qcs6490-rb3gen: add and enable BT node
2025-01-27 6:49 [PATCH v8 0/2] Enable Bluetooth on qcs6490-rb3gen2 board Janaki Ramaiah Thota
@ 2025-01-27 6:49 ` Janaki Ramaiah Thota
2025-01-27 7:31 ` Enable Bluetooth on qcs6490-rb3gen2 board bluez.test.bot
2025-01-27 6:49 ` [PATCH v8 2/2] Bluetooth: hci_qca: use the power sequencer for wcn6750 Janaki Ramaiah Thota
` (2 subsequent siblings)
3 siblings, 1 reply; 7+ messages in thread
From: Janaki Ramaiah Thota @ 2025-01-27 6:49 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Marcel Holtmann, Luiz Augusto von Dentz
Cc: quic_mohamull, quic_hbandi, quic_anubhavg, linux-arm-msm,
devicetree, linux-kernel, linux-bluetooth, Dmitry Baryshkov
Add the PMU node for WCN6750 present on the qcs6490-rb3gen
board and assign its power outputs to the Bluetooth module.
In WCN6750 module sw_ctrl and wifi-enable pins are handled
in the wifi controller firmware. Therefore, it is not required
to have those pins' entries in the PMU node.
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 168 ++++++++++++++++++-
1 file changed, 167 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
index 7a36c90ad4ec..a5668dbbe077 100644
--- a/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
+++ b/arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: BSD-3-Clause
/*
- * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2023-2024 Qualcomm Innovation Center, Inc. All rights reserved.
*/
/dts-v1/;
@@ -34,6 +34,7 @@ / {
aliases {
serial0 = &uart5;
+ serial1 = &uart7;
};
chosen {
@@ -218,6 +219,63 @@ vph_pwr: vph-pwr-regulator {
regulator-min-microvolt = <3700000>;
regulator-max-microvolt = <3700000>;
};
+
+ wcn6750-pmu {
+ compatible = "qcom,wcn6750-pmu";
+ pinctrl-names = "default";
+ pinctrl-0 = <&bt_en>;
+ vddaon-supply = <&vreg_s7b_0p972>;
+ vddasd-supply = <&vreg_l11c_2p8>;
+ vddpmu-supply = <&vreg_s7b_0p972>;
+ vddrfa0p8-supply = <&vreg_s7b_0p972>;
+ vddrfa1p2-supply = <&vreg_s8b_1p272>;
+ vddrfa1p7-supply = <&vreg_s1b_1p872>;
+ vddrfa2p2-supply = <&vreg_s1c_2p19>;
+
+ bt-enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p7: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p7";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
};
&apps_rsc {
@@ -799,6 +857,39 @@ &pon_resin {
status = "okay";
};
+&qup_uart7_cts {
+ /*
+ * Configure a bias-bus-hold on CTS to lower power
+ * usage when Bluetooth is turned off. Bus hold will
+ * maintain a low power state regardless of whether
+ * the Bluetooth module drives the pin in either
+ * direction or leaves the pin fully unpowered.
+ */
+ bias-bus-hold;
+};
+
+&qup_uart7_rts {
+ /* We'll drive RTS, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
+&qup_uart7_rx {
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module is
+ * in tri-state (module powered off or not driving the
+ * signal yet).
+ */
+ bias-pull-up;
+};
+
+&qup_uart7_tx {
+ /* We'll drive TX, so no pull */
+ drive-strength = <2>;
+ bias-disable;
+};
+
&qupv3_id_0 {
status = "okay";
};
@@ -842,12 +933,87 @@ &sdhc_2 {
&tlmm {
gpio-reserved-ranges = <32 2>, /* ADSP */
<48 4>; /* NFC */
+
+ bt_en: bt-en-state {
+ pins = "gpio85";
+ function = "gpio";
+ output-low;
+ bias-disable;
+ };
+
+ qup_uart7_sleep: qup_uart7_sleep {
+ qup_uart7_sleep_cts: qup-uart7-sleep-cts-state {
+ pins = "gpio28";
+ function = "gpio";
+ /*
+ * Configure a bias-bus-hold on CTS to lower power
+ * usage when Bluetooth is turned off. Bus hold will
+ * maintain a low power state regardless of whether
+ * the Bluetooth module drives the pin in either
+ * direction or leaves the pin fully unpowered.
+ */
+ bias-bus-hold;
+ };
+
+ qup_uart7_sleep_rts: qup-uart7-sleep-rts-state {
+ pins = "gpio29";
+ function = "gpio";
+ /*
+ * Configure pull-down on RTS. As RTS is active low
+ * signal, pull it low to indicate the BT SoC that it
+ * can wakeup the system anytime from suspend state by
+ * pulling RX low (by sending wakeup bytes).
+ */
+ bias-pull-down;
+ };
+
+ qup_uart7_sleep_rx: qup-uart7-sleep-rx-state {
+ pins = "gpio31";
+ function = "gpio";
+ /*
+ * Configure a pull-up on RX. This is needed to avoid
+ * garbage data when the TX pin of the Bluetooth module
+ * is floating which may cause spurious wakeups.
+ */
+ bias-pull-up;
+ };
+
+ qup_uart7_sleep_tx: qup-uart7-sleep-tx-state {
+ pins = "gpio30";
+ function = "gpio";
+ /*
+ * Configure pull-up on TX when it isn't actively driven
+ * to prevent BT SoC from receiving garbage during sleep.
+ */
+ bias-pull-up;
+ };
+ };
};
&uart5 {
status = "okay";
};
+&uart7 {
+ /delete-property/interrupts;
+ interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
+ <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-1 = <&qup_uart7_sleep>;
+ pinctrl-names = "default", "sleep";
+ status = "okay";
+
+ bluetooth: bluetooth {
+ compatible = "qcom,wcn6750-bt";
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ max-speed = <3200000>;
+ };
+};
+
&usb_1 {
status = "okay";
};
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 7+ messages in thread* RE: Enable Bluetooth on qcs6490-rb3gen2 board
2025-01-27 6:49 ` [PATCH v8 1/2] arm64: dts: qcom: qcs6490-rb3gen: add and enable BT node Janaki Ramaiah Thota
@ 2025-01-27 7:31 ` bluez.test.bot
0 siblings, 0 replies; 7+ messages in thread
From: bluez.test.bot @ 2025-01-27 7:31 UTC (permalink / raw)
To: linux-bluetooth, quic_janathot
[-- Attachment #1: Type: text/plain, Size: 2115 bytes --]
This is automated email and please do not reply to this email!
Dear submitter,
Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=928462
---Test result---
Test Summary:
CheckPatch PENDING 0.29 seconds
GitLint PENDING 0.18 seconds
SubjectPrefix FAIL 0.43 seconds
BuildKernel PASS 24.33 seconds
CheckAllWarning PASS 30.85 seconds
CheckSparse PASS 30.27 seconds
BuildKernel32 PASS 23.91 seconds
TestRunnerSetup PASS 431.15 seconds
TestRunner_l2cap-tester PASS 20.46 seconds
TestRunner_iso-tester PASS 32.22 seconds
TestRunner_bnep-tester PASS 4.94 seconds
TestRunner_mgmt-tester FAIL 122.74 seconds
TestRunner_rfcomm-tester PASS 7.61 seconds
TestRunner_sco-tester PASS 9.57 seconds
TestRunner_ioctl-tester PASS 8.23 seconds
TestRunner_mesh-tester PASS 6.10 seconds
TestRunner_smp-tester PASS 7.15 seconds
TestRunner_userchan-tester PASS 5.18 seconds
IncrementalBuild PENDING 0.37 seconds
Details
##############################
Test: CheckPatch - PENDING
Desc: Run checkpatch.pl script
Output:
##############################
Test: GitLint - PENDING
Desc: Run gitlint
Output:
##############################
Test: SubjectPrefix - FAIL
Desc: Check subject contains "Bluetooth" prefix
Output:
"Bluetooth: " prefix is not specified in the subject
##############################
Test: TestRunner_mgmt-tester - FAIL
Desc: Run mgmt-tester with test-runner
Output:
Total: 490, Passed: 485 (99.0%), Failed: 1, Not Run: 4
Failed Test Cases
LL Privacy - Set Flags 3 (2 Devices to RL) Failed 0.202 seconds
##############################
Test: IncrementalBuild - PENDING
Desc: Incremental build with the patches in the series
Output:
---
Regards,
Linux Bluetooth
^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v8 2/2] Bluetooth: hci_qca: use the power sequencer for wcn6750
2025-01-27 6:49 [PATCH v8 0/2] Enable Bluetooth on qcs6490-rb3gen2 board Janaki Ramaiah Thota
2025-01-27 6:49 ` [PATCH v8 1/2] arm64: dts: qcom: qcs6490-rb3gen: add and enable BT node Janaki Ramaiah Thota
@ 2025-01-27 6:49 ` Janaki Ramaiah Thota
2025-01-27 6:54 ` [PATCH v8 0/2] Enable Bluetooth on qcs6490-rb3gen2 board Krzysztof Kozlowski
2025-01-27 19:23 ` Rob Herring (Arm)
3 siblings, 0 replies; 7+ messages in thread
From: Janaki Ramaiah Thota @ 2025-01-27 6:49 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Marcel Holtmann, Luiz Augusto von Dentz
Cc: quic_mohamull, quic_hbandi, quic_anubhavg, linux-arm-msm,
devicetree, linux-kernel, linux-bluetooth, Dmitry Baryshkov
Older boards are having entry "enable-gpios" in dts, we can safely assume
latest boards which are supporting PMU node enrty will support power
sequencer.
Signed-off-by: Janaki Ramaiah Thota <quic_janathot@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
---
drivers/bluetooth/hci_qca.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/bluetooth/hci_qca.c b/drivers/bluetooth/hci_qca.c
index 0ac2168f1dc4..d2fd08aceb17 100644
--- a/drivers/bluetooth/hci_qca.c
+++ b/drivers/bluetooth/hci_qca.c
@@ -2359,6 +2359,7 @@ static int qca_serdev_probe(struct serdev_device *serdev)
switch (qcadev->btsoc_type) {
case QCA_WCN6855:
case QCA_WCN7850:
+ case QCA_WCN6750:
if (!device_property_present(&serdev->dev, "enable-gpios")) {
/*
* Backward compatibility with old DT sources. If the
@@ -2378,7 +2379,6 @@ static int qca_serdev_probe(struct serdev_device *serdev)
case QCA_WCN3990:
case QCA_WCN3991:
case QCA_WCN3998:
- case QCA_WCN6750:
qcadev->bt_power->dev = &serdev->dev;
err = qca_init_regulators(qcadev->bt_power, data->vregs,
data->num_vregs);
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [PATCH v8 0/2] Enable Bluetooth on qcs6490-rb3gen2 board
2025-01-27 6:49 [PATCH v8 0/2] Enable Bluetooth on qcs6490-rb3gen2 board Janaki Ramaiah Thota
2025-01-27 6:49 ` [PATCH v8 1/2] arm64: dts: qcom: qcs6490-rb3gen: add and enable BT node Janaki Ramaiah Thota
2025-01-27 6:49 ` [PATCH v8 2/2] Bluetooth: hci_qca: use the power sequencer for wcn6750 Janaki Ramaiah Thota
@ 2025-01-27 6:54 ` Krzysztof Kozlowski
2025-01-27 7:16 ` Janaki Ramaiah Thota
2025-01-27 19:23 ` Rob Herring (Arm)
3 siblings, 1 reply; 7+ messages in thread
From: Krzysztof Kozlowski @ 2025-01-27 6:54 UTC (permalink / raw)
To: Janaki Ramaiah Thota, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Marcel Holtmann,
Luiz Augusto von Dentz
Cc: quic_mohamull, quic_hbandi, quic_anubhavg, linux-arm-msm,
devicetree, linux-kernel, linux-bluetooth
On 27/01/2025 07:49, Janaki Ramaiah Thota wrote:
> Resending the below reviewed patches after fixing the regulator warnings in v7 P1.
> - Patch 1/2 Add and enable BT node for qcs6490-rb3gen board.
> - Patch 2/2 Use the power sequencer for wcn6750.
>
> ----
> Changes from v7:
> * updated P1 & P2 with tag: Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> * Link to v7: https://lore.kernel.org/lkml/20250107134157.211702-1-quic_janathot@quicinc.com/#t
>
> Changes from v6:
> * Elaborated the commit message with more information.
> * Link to v6: https://lore.kernel.org/lkml/20241223135700.22660-1-quic_janathot@quicinc.com/
These are entirely different patchsets - bindings only.
Why is this v8?
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v8 0/2] Enable Bluetooth on qcs6490-rb3gen2 board
2025-01-27 6:54 ` [PATCH v8 0/2] Enable Bluetooth on qcs6490-rb3gen2 board Krzysztof Kozlowski
@ 2025-01-27 7:16 ` Janaki Ramaiah Thota
0 siblings, 0 replies; 7+ messages in thread
From: Janaki Ramaiah Thota @ 2025-01-27 7:16 UTC (permalink / raw)
To: Krzysztof Kozlowski, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Marcel Holtmann,
Luiz Augusto von Dentz
Cc: quic_mohamull, quic_hbandi, quic_anubhavg, linux-arm-msm,
devicetree, linux-kernel, linux-bluetooth
On 1/27/2025 12:24 PM, Krzysztof Kozlowski wrote:
> On 27/01/2025 07:49, Janaki Ramaiah Thota wrote:
>> Resending the below reviewed patches after fixing the regulator warnings in v7 P1.
>> - Patch 1/2 Add and enable BT node for qcs6490-rb3gen board.
>> - Patch 2/2 Use the power sequencer for wcn6750.
>>
>> ----
>> Changes from v7:
>> * updated P1 & P2 with tag: Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
>> * Link to v7: https://lore.kernel.org/lkml/20250107134157.211702-1-quic_janathot@quicinc.com/#t
>>
>> Changes from v6:
>> * Elaborated the commit message with more information.
>> * Link to v6: https://lore.kernel.org/lkml/20241223135700.22660-1-quic_janathot@quicinc.com/
> These are entirely different patchsets - bindings only.
>
Thanks for the quick review Krzysztof,
Initially we are getting below regulator warnings in patch version 5(v5)
and we fixed those by patch 1 verion 7(v7-p1)
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth:
'enable-gpios' is a required property
from schema $id:
http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth:
'swctrl-gpios' is a required property
from schema $id:
http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth:
'vddio-supply' is a required property
from schema $id:
http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth:
'vddbtcxmx-supply' is a required property
from schema $id:
http://devicetree.org/schemas/net/bluetooth/qualcomm-bluetooth.yaml#
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: bluetooth:
'vddasd-supply' is a required property
Explained complete history here :
https://lore.kernel.org/lkml/d3bd97d8-43fb-452b-adca-ad03eb628031@quicinc.com/
> Why is this v8?
>
To maintain complete history updated to v8
Thanks,
Janakiram
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v8 0/2] Enable Bluetooth on qcs6490-rb3gen2 board
2025-01-27 6:49 [PATCH v8 0/2] Enable Bluetooth on qcs6490-rb3gen2 board Janaki Ramaiah Thota
` (2 preceding siblings ...)
2025-01-27 6:54 ` [PATCH v8 0/2] Enable Bluetooth on qcs6490-rb3gen2 board Krzysztof Kozlowski
@ 2025-01-27 19:23 ` Rob Herring (Arm)
3 siblings, 0 replies; 7+ messages in thread
From: Rob Herring (Arm) @ 2025-01-27 19:23 UTC (permalink / raw)
To: Janaki Ramaiah Thota
Cc: linux-kernel, linux-bluetooth, quic_hbandi, linux-arm-msm,
quic_anubhavg, Krzysztof Kozlowski, devicetree, Marcel Holtmann,
Bjorn Andersson, Luiz Augusto von Dentz, quic_mohamull,
Konrad Dybcio, Conor Dooley
On Mon, 27 Jan 2025 12:19:38 +0530, Janaki Ramaiah Thota wrote:
> Resending the below reviewed patches after fixing the regulator warnings in v7 P1.
> - Patch 1/2 Add and enable BT node for qcs6490-rb3gen board.
> - Patch 2/2 Use the power sequencer for wcn6750.
>
> ----
> Changes from v7:
> * updated P1 & P2 with tag: Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
> * Link to v7: https://lore.kernel.org/lkml/20250107134157.211702-1-quic_janathot@quicinc.com/#t
>
> Changes from v6:
> * Elaborated the commit message with more information.
> * Link to v6: https://lore.kernel.org/lkml/20241223135700.22660-1-quic_janathot@quicinc.com/
>
> Changes from v5:
> * Update the wcn6750 required properties in bindings.
> * Link to v5: https://lore.kernel.org/linux-arm-msm/20241209103455.9675-1-quic_janathot@quicinc.com/
>
> Changes from v4:
> * Added reviewed tag by Krzysztof in p1
> * Updated the p2 commit message with sw_ctrl and wifi-enable are
> handled in wifi FW.
> * Added blank line between the nodes in p2
> * Placed the structures in proper order in p4
> * Link to v4: https://lore.kernel.org/all/20241204131706.20791-1-quic_janathot@quicinc.com/
>
> Changes from v3:
> * Defined the PMU node and used the its output to power up BT
> * Used power sequencer for wcn wcn6750 module
> * Split the patch to multiple as per subtree
> * Add description of the PMU of the WCN6750 module
> * Include separate UART state node for sleep pin configuarion
> * Link to v3: https://lore.kernel.org/linux-arm-msm/20241022104600.3228-1-quic_janathot@quicinc.com/
>
> Changes from v2:
> * Sorted nodes alphabetically
> * Link to v2: https://lore.kernel.org/linux-arm-msm/20241010105107.30118-1-quic_janathot@quicinc.com/
>
> Changes from v1:
> * Corrected the board name in subject
> * Link to v1: https://lore.kernel.org/linux-arm-msm/20241009111436.23473-1-quic_janathot@quicinc.com/
> Janaki Ramaiah Thota (2):
> arm64: dts: qcom: qcs6490-rb3gen: add and enable BT node
> Bluetooth: hci_qca: use the power sequencer for wcn6750
>
> arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dts | 168 ++++++++++++++++++-
> drivers/bluetooth/hci_qca.c | 2 +-
> 2 files changed, 168 insertions(+), 2 deletions(-)
>
> --
>
>
>
>
My bot found new DTB warnings on the .dts files added or changed in this
series.
Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.
If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:
pip3 install dtschema --upgrade
New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/qcom/' for 20250127064940.1360404-1-quic_janathot@quicinc.com:
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: pmic@2: pwm:nvmem: [[352, 353]] is too short
from schema $id: http://devicetree.org/schemas/mfd/qcom,spmi-pmic.yaml#
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: pwm: nvmem: [[352, 353]] is too short
from schema $id: http://devicetree.org/schemas/leds/leds-qcom-lpg.yaml#
arch/arm64/boot/dts/qcom/qcs6490-rb3gen2.dtb: pinctrl@f100000: Unevaluated properties are not allowed ('qup_uart7_sleep' was unexpected)
from schema $id: http://devicetree.org/schemas/pinctrl/qcom,sc7280-pinctrl.yaml#
^ permalink raw reply [flat|nested] 7+ messages in thread