[Bluez-users] bt on acer tm 4501

[Bluez-users] bt on acer tm 4501

[ultrakorne]

hi, i have some problem to get my bt working on my acer travelmate 4501.
i have a button to "activate" bt, but pressing its useless (
Unknown key pressed (translated set 2, code 0xd6 on isa0060/serio0).
atkbd.c: Use 'setkeycodes e056 <keycode>' to make it known )

i am using ubuntu kernel 2.6.8.1
i have installed bluez utils and started modprobing some modules 
(hci_usb, bfusb (bluez),rfcomm, sco, l2cap. running

  Starting bluez-utils: hcid rfcomm sdpd.
Switching on Bluetooth input devices.
No devices in HCI mode found

hciconfig hci0 up:
Can't get device info: No such device

lsusb can find only my usb mouse...

dmesg out (only a small part):

Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00f6370
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xab88, dseg 0x400
pnp: 00:0a: ioport range 0xfe00-0xfe01 could not be reserved
pnp: 00:0c: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:0c: ioport range 0x1000-0x105f could not be reserved
pnp: 00:0c: ioport range 0x1060-0x107f has been reserved
pnp: 00:0c: ioport range 0x1180-0x11bf has been reserved
PnPBIOS: 20 nodes reported by PnP BIOS; 20 recorded by driver
PCI: Using ACPI for IRQ routing
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 6
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 6 (level, low) -> IRQ 6
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 6 (level, low) -> IRQ 6
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 6 (level, low) -> IRQ 6
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 6
ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 6 (level, low) -> IRQ 6
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 6 (level, low) -> IRQ 6
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 6 (level, low) -> IRQ 6
ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:02:06.2[A] -> GSI 10 (level, low) -> IRQ 10
ACPI: PCI interrupt 0000:02:06.3[A] -> GSI 10 (level, low) -> IRQ 10
Simple Boot Flag at 0x37 set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A


so... ttys0 is bt?? (more dmesg is needed?)
i tryed using uart loading some modules and irattach ttys0 using any. 
hciconfig show a down inteface... and cannot be upped (timeout occurs)

i cant find some howto that seems to have a problem like mine, i hope 
here i can get some tips... thx

regards


-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users

Re: [Bluez-users] bt on acer tm 4501

[Marcel Holtmann]

Hi,

> i have some problem to get my bt working on my acer travelmate 4501.
> i have a button to "activate" bt, but pressing its useless (
> Unknown key pressed (translated set 2, code 0xd6 on isa0060/serio0).
> atkbd.c: Use 'setkeycodes e056 <keycode>' to make it known )
> 
> i am using ubuntu kernel 2.6.8.1
> i have installed bluez utils and started modprobing some modules 
> (hci_usb, bfusb (bluez),rfcomm, sco, l2cap. running
> 
>   Starting bluez-utils: hcid rfcomm sdpd.
> Switching on Bluetooth input devices.
> No devices in HCI mode found
> 
> hciconfig hci0 up:
> Can't get device info: No such device
> 
> lsusb can find only my usb mouse...
> 
> dmesg out (only a small part):
> 
> Linux Plug and Play Support v0.97 (c) Adam Belay
> PnPBIOS: Scanning system for PnP BIOS support...
> PnPBIOS: Found PnP BIOS installation structure at 0xc00f6370
> PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xab88, dseg 0x400
> pnp: 00:0a: ioport range 0xfe00-0xfe01 could not be reserved
> pnp: 00:0c: ioport range 0x4d0-0x4d1 has been reserved
> pnp: 00:0c: ioport range 0x1000-0x105f could not be reserved
> pnp: 00:0c: ioport range 0x1060-0x107f has been reserved
> pnp: 00:0c: ioport range 0x1180-0x11bf has been reserved
> PnPBIOS: 20 nodes reported by PnP BIOS; 20 recorded by driver
> PCI: Using ACPI for IRQ routing
> ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 6
> ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6
> ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 6
> ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
> ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
> ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
> ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:02:06.2[A] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:02:06.3[A] -> GSI 10 (level, low) -> IRQ 10
> Simple Boot Flag at 0x37 set to 0x1
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
> devfs: boot_options: 0x0
> Initializing Cryptographic API
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
> 
> 
> so... ttys0 is bt?? (more dmesg is needed?)
> i tryed using uart loading some modules and irattach ttys0 using any. 
> hciconfig show a down inteface... and cannot be upped (timeout occurs)

what the hell has irattach to do with Bluetooth? I actually doubt that
ttyS0 is your Bluetooth devices. Normally these things are attached to
the USB bus and must be activated. Try to include the Acer ACPI module
and check for its options to activate Bluetooth.

Regards

Marcel




-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users

Re: [Bluez-users] bt on acer tm 4501

[Michal Semler]

Try acerhk module

Michal

Dne po 13. prosince 2004 02:19 ultrakorne napsal(a):
> hi, i have some problem to get my bt working on my acer travelmate 4501.
> i have a button to "activate" bt, but pressing its useless (
> Unknown key pressed (translated set 2, code 0xd6 on isa0060/serio0).
> atkbd.c: Use 'setkeycodes e056 <keycode>' to make it known )
>
> i am using ubuntu kernel 2.6.8.1
> i have installed bluez utils and started modprobing some modules
> (hci_usb, bfusb (bluez),rfcomm, sco, l2cap. running
>
>   Starting bluez-utils: hcid rfcomm sdpd.
> Switching on Bluetooth input devices.
> No devices in HCI mode found
>
> hciconfig hci0 up:
> Can't get device info: No such device
>
> lsusb can find only my usb mouse...
>
> dmesg out (only a small part):
>
> Linux Plug and Play Support v0.97 (c) Adam Belay
> PnPBIOS: Scanning system for PnP BIOS support...
> PnPBIOS: Found PnP BIOS installation structure at 0xc00f6370
> PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xab88, dseg 0x400
> pnp: 00:0a: ioport range 0xfe00-0xfe01 could not be reserved
> pnp: 00:0c: ioport range 0x4d0-0x4d1 has been reserved
> pnp: 00:0c: ioport range 0x1000-0x105f could not be reserved
> pnp: 00:0c: ioport range 0x1060-0x107f has been reserved
> pnp: 00:0c: ioport range 0x1180-0x11bf has been reserved
> PnPBIOS: 20 nodes reported by PnP BIOS; 20 recorded by driver
> PCI: Using ACPI for IRQ routing
> ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 6
> ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 6
> ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 6
> ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 10
> ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
> ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:00:1f.6[B] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 6 (level, low) -> IRQ 6
> ACPI: PCI interrupt 0000:02:04.0[A] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
> ACPI: PCI interrupt 0000:02:06.0[A] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:02:06.2[A] -> GSI 10 (level, low) -> IRQ 10
> ACPI: PCI interrupt 0000:02:06.3[A] -> GSI 10 (level, low) -> IRQ 10
> Simple Boot Flag at 0x37 set to 0x1
> VFS: Disk quotas dquot_6.5.1
> Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
> devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
> devfs: boot_options: 0x0
> Initializing Cryptographic API
> isapnp: Scanning for PnP cards...
> isapnp: No Plug & Play device found
> Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
> ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> ttyS1 at I/O 0x2f8 (irq = 3) is a NS16550A
>
>
> so... ttys0 is bt?? (more dmesg is needed?)
> i tryed using uart loading some modules and irattach ttys0 using any.
> hciconfig show a down inteface... and cannot be upped (timeout occurs)
>
> i cant find some howto that seems to have a problem like mine, i hope
> here i can get some tips... thx
>
> regards
>
>
> -------------------------------------------------------
> SF email is sponsored by - The IT Product Guide
> Read honest & candid reviews on hundreds of IT Products from real users.
> Discover which products truly live up to the hype. Start reading now.
> http://productguide.itmanagersjournal.com/
> _______________________________________________
> Bluez-users mailing list
> Bluez-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/bluez-users


-------------------------------------------------------
SF email is sponsored by - The IT Product Guide
Read honest & candid reviews on hundreds of IT Products from real users.
Discover which products truly live up to the hype. Start reading now. 
http://productguide.itmanagersjournal.com/
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users