[Bluez-users] Trouble with Tecom BT3030 - not recognized

[Bluez-users] Trouble with Tecom BT3030 - not recognized

[Thomas Börkel]

HI!

I had a Tecom BT3030 running OK on Suse 10.1 with Kernel 2.6.16, Bluez
2.24 and Bluez firmware 1.0.

Now (since a few days) I am on Gentoo with Kernel 2.6.23 and I have tried:
- Bluez 2.25 + Bluez firmware 1.1
- Bluez 3.23 + Bluez firmware 1.1
- Bluez 3.23 + Bluez firmware 1.1

It's always the same. When I put the dongle into the USB port, I get
only this:
usb 3-1: new full speed USB device using uhci_hcd and address 9
usb 3-1: configuration #1 chosen from 1 choice

When I remove it, I get this:
bcm203x_complete: URB failed with status -84
or this:
usb 3-1: USB disconnect, address 9


My system should be installed correctly, because an Anycom 2.0 dongle
works flawlessly:
usb 3-1: new full speed USB device using uhci_hcd and address 10
usb 3-1: configuration #1 chosen from 1 choice
hcid[12188]: HCI dev 0 registered
Jan  1 21:36:01 asus hcid[12188]: HCI dev 0 up
Jan  1 21:36:01 asus hcid[12188]: Device hci0 has been added
Jan  1 21:36:01 asus hcid[12188]: Starting security manager 0
Jan  1 21:36:01 asus hcid[12188]: Device hci0 has been activated


lsusb with the non-working Tecom:
Bus 003 Device 011: ID 0a5c:2033 Broadcom Corp. BCM2033 Bluetooth


Somehow hcid does not react to the Tecom?

BTW, I also tried this with another new Gentoo system with the same
result. I somehow can't believe the Tecom died at the same time I
reinstalled the system.

Any help would be greatly appreciated. Thanks!

Thomas

-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users

Re: [Bluez-users] Trouble with Tecom BT3030 - not recognized

[Thomas Börkel]

HI!

Sorry, typo:

Thomas B=F6rkel wrote:

> Now (since a few days) I am on Gentoo with Kernel 2.6.23 and I have tried:
> - Bluez 2.25 + Bluez firmware 1.1
> - Bluez 3.23 + Bluez firmware 1.1
> - Bluez 3.23 + Bluez firmware 1.1

The last line should have been:
- Bluez 3.23 + Bluez firmware 1.2

Thomas


-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users

Re: [Bluez-users] Trouble with Tecom BT3030 - not recognized

[Thomas Börkel]

HI!

I think, I am a small step further.

I guess, the working Anycom USB-250 device has a firmware onboard, where
as the Tecom BT3030 needs the firmware to be loaded when plugging it in
and this is what not works.

I have firmware loading support in the kernel (standard Gentoo 2.6.23
kernel) active and it works for an ivtv video capture card.

So I tried manually uploading the firmware to the dongle like this:
/etc/init.d/bluetooth stop
bluefw usb 004/003;/etc/init.d/bluetooth start

This worked one time and hciconfig showed the device (so it is not wrecked).

But now this gives me:
bluefw[13626]: Loading firmware to usb device 0a5c:2033
bluefw[13626]: Can't claim interface 0. Device or resource busy (16)

Anyway, normally hotplug should load the firmware into the device. I did
not have the hotplug package installed but now I have and it makes no
difference.

Any ideas?

Thanks!

Thomas



-------------------------------------------------------------------------
This SF.net email is sponsored by: Microsoft
Defy all challenges. Microsoft(R) Visual Studio 2005.
http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users

Re: [Bluez-users] Trouble with Tecom BT3030 - not recognized

[Thomas Börkel]

HI!

No one any hints for me, about why the firmware is not being loaded onto 
the dongle?

Thomas


-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://ad.doubleclick.net/clk;164216239;13503038;w?http://sf.net/marketplace
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users