[PATCH v2 0/6] Add support for IPQ5018 Bluetooth

[PATCH v2 0/6] Add support for IPQ5018 Bluetooth

[George Moussalem via B4 Relay]

Hello,

This patch series introduces Bluetooth support for IPQ5018.

Bluetooth firmware is loaded by the host into a dedicated reserved
memory carveout and authenticated by TrustZone. A Secure Channel Manager
(SCM) call safely brings the peripheral core out of reset.

A shared memory ring buffer topology handles runtime data frame
transport between the host APSS and the Bluetooth controller.
An outgoing APCS IPC bit and an incoming GIC interrupt handle
host/guest signaling.

This series has been tested and verified on various IPQ5018 router
boards utilizing firmware extracted from GPL distributions, using both
mdt and mbn file formats.

[   14.781511] Bluetooth: hci0: QCA Product ID   :0x00000016
[   14.781583] Bluetooth: hci0: QCA SOC Version  :0x20180100
[   14.785926] Bluetooth: hci0: QCA ROM Version  :0x00000100
[   14.791546] Bluetooth: hci0: QCA Patch Version:0x00003ded
[   14.796698] Bluetooth: hci0: QCA controller version 0x01000100
[   14.802217] Bluetooth: hci0: QCA Downloading qca/mpnv10.bin
[   16.393850] Bluetooth: hci0: QCA Build Info: BTFW.MAPLE.1.0.0-00102-MPL_ROM_PATCHZ-1

Best regards,
George Moussalem

Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
Changes in v2:
- removed unused struct member btss_reset from m0_btss struct.
- used devm_reset_control_get_exclusive_deasserted to acquire and
  deassert btss_reset in one call. No need to explicitly assert upon
  unbind since devres will handle it.
- As per Bjorn's comments, collapsed the rproc and BT driver into one
  which now handles firmware loading and transport.
- As per further review comments and above change, squashed the two
  devicetree bindings into one to represent the Bluetooth controller
- Added new SCM call to drive Bluetooth power modes. Based on testing on
  more router boards, this is required during start/stop sequences to
  avoid the controller hanging. This is only supported on relatively
  newer QSEE versions, so the SCM call is checked for availability
  before use.
- Refactored resource lifecycle management in the driver so that IRQ and
  work queue are managed at the driver level (probe/remove) while FW
  loading and powering on/off the controller is handled upon hdev
  open/close.
- Consolidated TX send functions for custom IPC and HCI frames into one
  and solved a potential NULL pointer dereference issue under TX
  pressure.
- Replace code to load and initialize firmware metadate by existing
  qcom_mdt_pas_init function. 
- Solved an off byone calculation error in the RX parser.
- Added entry to MAINTAINERS file
- Link to v1: https://lore.kernel.org/r/20260625-ipq5018-bluetooth-v1-0-d999be0e04f7@outlook.com

---
George Moussalem (6):
      dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller
      Bluetooth: btqca: Add IPQ5018 support
      firmware: qcom: scm: Add support for setting Bluetooth power modes
      Bluetooth: Introduce Qualcomm IPQ5018 IPC based HCI driver
      arm64: dts: qcom: ipq5018: add nodes required for Bluetooth support
      MAINTAINERS: Add entry for Qualcomm IPQ5018 Bluetooth driver

 .../bindings/net/bluetooth/qcom,ipq5018-bt.yaml    |   86 ++
 MAINTAINERS                                        |    7 +
 arch/arm64/boot/dts/qcom/ipq5018.dtsi              |   25 +-
 drivers/bluetooth/Kconfig                          |   11 +
 drivers/bluetooth/Makefile                         |    1 +
 drivers/bluetooth/btqca.c                          |   16 +
 drivers/bluetooth/btqca.h                          |    3 +
 drivers/bluetooth/btqcomipc.c                      | 1052 ++++++++++++++++++++
 drivers/firmware/qcom/qcom_scm.c                   |   49 +
 drivers/firmware/qcom/qcom_scm.h                   |    1 +
 include/linux/firmware/qcom/qcom_scm.h             |    1 +
 11 files changed, 1251 insertions(+), 1 deletion(-)
---
base-commit: 4d1ab324fcb7d20df5a071edb0304461846fdc12
change-id: 20260625-ipq5018-bluetooth-06ff66c9d753
prerequisite-message-id: <20260612-block-as-nvmem-v5-0-95e0b30fff90@oss.qualcomm.com>
prerequisite-patch-id: 6ce8686c1683f468d86b4502f5ec9d19c392a382
prerequisite-patch-id: e362f7fcbacff716b7ef720e6780786a7d88c013
prerequisite-patch-id: 9168930e40551e842c8171d5433a6f39ad4b78a4
prerequisite-patch-id: 64fecfbd1e085d7d2ab0ae23295ca34ec8e14c5e
prerequisite-patch-id: 566804aaa690ee9aa285d0fd75fd16d94fbadebf
prerequisite-patch-id: dc18bec338f54b3051f4523f9d1d3c0566a20ccd
prerequisite-patch-id: b6b3eb46429936ab49423d295433daf47981db0f
prerequisite-patch-id: 75caa99e3bbcdf41b6462b9f5f703bea1d4a65fa
prerequisite-patch-id: 35e9968f482f78ca233eb0306d9c5fdbff093175

Best regards,
-- 
George Moussalem <george.moussalem@outlook.com>

[PATCH v2 1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

[George Moussalem via B4 Relay]

From: George Moussalem <george.moussalem@outlook.com>

Document the Qualcomm IPQ5018 Bluetooth controller.

Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
 .../bindings/net/bluetooth/qcom,ipq5018-bt.yaml    | 86 ++++++++++++++++++++++
 1 file changed, 86 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/bluetooth/qcom,ipq5018-bt.yaml b/Documentation/devicetree/bindings/net/bluetooth/qcom,ipq5018-bt.yaml
new file mode 100644
index 000000000000..2119162994e0
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/bluetooth/qcom,ipq5018-bt.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/bluetooth/qcom,ipq5018-bt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm IPQ5018 Bluetooth
+
+maintainers:
+  - George Moussalem <george.moussalem@outlook.com>
+
+properties:
+  compatible:
+    enum:
+      - qcom,ipq5018-bt
+
+  clocks:
+    items:
+      - description: Bluetooth Subsystem low power oscillator clock
+
+  clock-names:
+    items:
+      - const: lpo
+
+  firmware-name:
+    maxItems: 1
+
+  memory-region:
+    items:
+      - description: |
+          Reserved memory carveout for firmware loading and runtime data
+          transport between the host and the Bluetooth controller.
+
+  interrupts:
+    maxItems: 1
+
+  qcom,ipc:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    items:
+      - items:
+          - description: syscon node representing the APCS registers
+          - description: offset to the register within the syscon
+          - description: IPC bit within the register
+    description: |
+      The outgoing IPC bit used for signaling the Bluetooth controller of a host
+      event or for sending an ACK if the remote processor expects it.
+
+  resets:
+    items:
+      - description: Bluetooth Subsystem reset
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - firmware-name
+  - interrupts
+  - qcom,ipc
+  - resets
+
+allOf:
+  - $ref: bluetooth-controller.yaml#
+  - $ref: qcom,bluetooth-common.yaml
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
+
+    bluetooth {
+      compatible = "qcom,ipq5018-bt";
+
+      firmware-name = "qca/bt_fw_patch.mbn";
+
+      clocks = <&gcc GCC_BTSS_LPO_CLK>;
+      clock-names = "lpo";
+      resets = <&gcc GCC_BTSS_BCR>;
+
+      qcom,ipc = <&apcs_glb 8 23>;
+      interrupts = <GIC_SPI 162 IRQ_TYPE_EDGE_RISING>;
+
+      memory-region = <&btss_region>;
+    };

-- 
2.53.0

RE: Add support for IPQ5018 Bluetooth

[bluez.test.bot]

[-- Attachment #1: Type: text/plain, Size: 4350 bytes --]

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=1118237

---Test result---

Test Summary:
CheckPatch                    FAIL      10.52 seconds
VerifyFixes                   PASS      0.21 seconds
VerifySignedoff               PASS      0.24 seconds
GitLint                       FAIL      4.28 seconds
SubjectPrefix                 FAIL      2.16 seconds
BuildKernel                   PASS      25.41 seconds
CheckAllWarning               PASS      28.30 seconds
CheckSparse                   PASS      28.42 seconds
BuildKernel32                 PASS      24.73 seconds
CheckKernelLLVM               SKIP      0.00 seconds
TestRunnerSetup               PASS      457.14 seconds
TestRunner_l2cap-tester       PASS      57.17 seconds
TestRunner_iso-tester         PASS      80.06 seconds
TestRunner_bnep-tester        PASS      19.10 seconds
TestRunner_mgmt-tester        FAIL      208.31 seconds
TestRunner_rfcomm-tester      PASS      25.26 seconds
TestRunner_sco-tester         PASS      31.86 seconds
TestRunner_ioctl-tester       PASS      25.76 seconds
TestRunner_mesh-tester        FAIL      25.21 seconds
TestRunner_smp-tester         PASS      23.11 seconds
TestRunner_userchan-tester    PASS      22.68 seconds
TestRunner_6lowpan-tester     PASS      23.40 seconds
IncrementalBuild              PASS      37.85 seconds

Details
##############################
Test: CheckPatch - FAIL
Desc: Run checkpatch.pl script
Output:
[v2,1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#106: 
new file mode 100644

total: 0 errors, 1 warnings, 86 lines checked

NOTE: For some of the reported defects, checkpatch may be able to
      mechanically convert to the typical style using --fix or --fix-inplace.

/github/workspace/src/patch/14651116.patch has style problems, please review.

NOTE: Ignored message types: UNKNOWN_COMMIT_ID

NOTE: If any of the errors are false positives, please report
      them to the maintainer, see CHECKPATCH in MAINTAINERS.


[v2,4/6] Bluetooth: Introduce Qualcomm IPQ5018 IPC based HCI driver
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#154: 
new file mode 100644

total: 0 errors, 1 warnings, 1076 lines checked

NOTE: For some of the reported defects, checkpatch may be able to
      mechanically convert to the typical style using --fix or --fix-inplace.

/github/workspace/src/patch/14651118.patch has style problems, please review.

NOTE: Ignored message types: UNKNOWN_COMMIT_ID

NOTE: If any of the errors are false positives, please report
      them to the maintainer, see CHECKPATCH in MAINTAINERS.


##############################
Test: GitLint - FAIL
Desc: Run gitlint
Output:
[v2,1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

1: T1 Title exceeds max length (84>80): "[v2,1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller"
##############################
Test: SubjectPrefix - FAIL
Desc: Check subject contains "Bluetooth" prefix
Output:
"Bluetooth: " prefix is not specified in the subject
"Bluetooth: " prefix is not specified in the subject
"Bluetooth: " prefix is not specified in the subject
"Bluetooth: " prefix is not specified in the subject
##############################
Test: CheckKernelLLVM - SKIP
Desc: Build kernel with LLVM + context analysis
Output:
Clang not found
##############################
Test: TestRunner_mgmt-tester - FAIL
Desc: Run mgmt-tester with test-runner
Output:
Total: 494, Passed: 489 (99.0%), Failed: 1, Not Run: 4

Failed Test Cases
Read Exp Feature - Success                           Failed       0.238 seconds
##############################
Test: TestRunner_mesh-tester - FAIL
Desc: Run mesh-tester with test-runner
Output:
Total: 10, Passed: 8 (80.0%), Failed: 2, Not Run: 0

Failed Test Cases
Mesh - Send cancel - 1                               Timed out    1.964 seconds
Mesh - Send cancel - 2                               Timed out    1.989 seconds


https://github.com/bluez/bluetooth-next/pull/368

---
Regards,
Linux Bluetooth

Re: [PATCH v2 1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

[Krzysztof Kozlowski]

On Mon, Jun 29, 2026 at 05:01:44PM +0400, George Moussalem wrote:
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
> +
> +    bluetooth {

Don't send new versions while discussion is still going. I need to
repeat my question - what bus does that sit on?

Device nodes represent real devices. Real devices sit on a bus, usually.
Do you have here a bus?

> +      compatible = "qcom,ipq5018-bt";

Best regards,
Krzysztof

Re: [PATCH v2 1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

[George Moussalem]

On 6/30/26 11:15, Krzysztof Kozlowski wrote:
> On Mon, Jun 29, 2026 at 05:01:44PM +0400, George Moussalem wrote:
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
>> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
>> +    #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
>> +
>> +    bluetooth {
> 
> Don't send new versions while discussion is still going. I need to
> repeat my question - what bus does that sit on?
> 
> Device nodes represent real devices. Real devices sit on a bus, usually.
> Do you have here a bus?

I'm afraid I don't have a definitive answer. Again, my understanding
based on downstream code is that the 'controller' is basically a Cortex
M0 processor running Bluetooth firmware connected to an RF. Data
transport is over a shared memory carveout with APPS signaling the
controller through writes to an IPC mailbox register, while the
controller has an interrupt line back to signal APPS.

> 
>> +      compatible = "qcom,ipq5018-bt";
> 
> Best regards,
> Krzysztof
> 

Best regards,
George

Re: [PATCH v2 1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

[Krzysztof Kozlowski]

On 30/06/2026 09:31, George Moussalem wrote:
> On 6/30/26 11:15, Krzysztof Kozlowski wrote:
>> On Mon, Jun 29, 2026 at 05:01:44PM +0400, George Moussalem wrote:
>>> +unevaluatedProperties: false
>>> +
>>> +examples:
>>> +  - |
>>> +    #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
>>> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
>>> +    #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
>>> +
>>> +    bluetooth {
>>
>> Don't send new versions while discussion is still going. I need to
>> repeat my question - what bus does that sit on?
>>
>> Device nodes represent real devices. Real devices sit on a bus, usually.
>> Do you have here a bus?
> 
> I'm afraid I don't have a definitive answer. Again, my understanding
> based on downstream code is that the 'controller' is basically a Cortex
> M0 processor running Bluetooth firmware connected to an RF. Data
> transport is over a shared memory carveout with APPS signaling the
> controller through writes to an IPC mailbox register, while the
> controller has an interrupt line back to signal APPS.

So this looks like should be squashed into remoteproc node. There is no
reason or no data to express it as two separate device nodes.

Best regards,
Krzysztof

Re: [PATCH v2 1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

[George Moussalem]

On 6/30/26 11:40, Krzysztof Kozlowski wrote:
> On 30/06/2026 09:31, George Moussalem wrote:
>> On 6/30/26 11:15, Krzysztof Kozlowski wrote:
>>> On Mon, Jun 29, 2026 at 05:01:44PM +0400, George Moussalem wrote:
>>>> +unevaluatedProperties: false
>>>> +
>>>> +examples:
>>>> +  - |
>>>> +    #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
>>>> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
>>>> +    #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
>>>> +
>>>> +    bluetooth {
>>>
>>> Don't send new versions while discussion is still going. I need to
>>> repeat my question - what bus does that sit on?
>>>
>>> Device nodes represent real devices. Real devices sit on a bus, usually.
>>> Do you have here a bus?
>>
>> I'm afraid I don't have a definitive answer. Again, my understanding
>> based on downstream code is that the 'controller' is basically a Cortex
>> M0 processor running Bluetooth firmware connected to an RF. Data
>> transport is over a shared memory carveout with APPS signaling the
>> controller through writes to an IPC mailbox register, while the
>> controller has an interrupt line back to signal APPS.
> 
> So this looks like should be squashed into remoteproc node. There is no
> reason or no data to express it as two separate device nodes.

In this version, I've squashed them into one already but as a Bluetooth
controller as that's what the 'processor' is dedicated to, also in line
with Bjorn's guidance to manage the lifecycle of this processor and all
other resources in one. Kindly let me know if this approach is satisfactory.

> 
> Best regards,
> Krzysztof

Best regards,
George

Re: [PATCH v2 1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

[Krzysztof Kozlowski]

On 30/06/2026 09:55, George Moussalem wrote:
> On 6/30/26 11:40, Krzysztof Kozlowski wrote:
>> On 30/06/2026 09:31, George Moussalem wrote:
>>> On 6/30/26 11:15, Krzysztof Kozlowski wrote:
>>>> On Mon, Jun 29, 2026 at 05:01:44PM +0400, George Moussalem wrote:
>>>>> +unevaluatedProperties: false
>>>>> +
>>>>> +examples:
>>>>> +  - |
>>>>> +    #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
>>>>> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
>>>>> +    #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
>>>>> +
>>>>> +    bluetooth {
>>>>
>>>> Don't send new versions while discussion is still going. I need to
>>>> repeat my question - what bus does that sit on?
>>>>
>>>> Device nodes represent real devices. Real devices sit on a bus, usually.
>>>> Do you have here a bus?
>>>
>>> I'm afraid I don't have a definitive answer. Again, my understanding
>>> based on downstream code is that the 'controller' is basically a Cortex
>>> M0 processor running Bluetooth firmware connected to an RF. Data
>>> transport is over a shared memory carveout with APPS signaling the
>>> controller through writes to an IPC mailbox register, while the
>>> controller has an interrupt line back to signal APPS.
>>
>> So this looks like should be squashed into remoteproc node. There is no
>> reason or no data to express it as two separate device nodes.
> 
> In this version, I've squashed them into one already but as a Bluetooth
> controller as that's what the 'processor' is dedicated to, also in line
> with Bjorn's guidance to manage the lifecycle of this processor and all
> other resources in one. Kindly let me know if this approach is satisfactory.
> 

I read changelog twice and only then found it mentions squashing it. I
suggest writing concise entries and drop all boiler plate like "As per
further review comments". I just ignore such paragraphs.

Best regards,
Krzysztof

Re: [PATCH v2 1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

[Konrad Dybcio]

On 6/30/26 9:15 AM, Krzysztof Kozlowski wrote:
> On Mon, Jun 29, 2026 at 05:01:44PM +0400, George Moussalem wrote:
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
>> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
>> +    #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
>> +
>> +    bluetooth {
> 
> Don't send new versions while discussion is still going. I need to
> repeat my question - what bus does that sit on?
> 
> Device nodes represent real devices. Real devices sit on a bus, usually.
> Do you have here a bus?

+Kathiravan would you know what the remoteproc-driven bluetooth is
connected over on IPQ5018?

Konrad

Re: [PATCH v2 1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

[Krzysztof Kozlowski]

On 30/06/2026 11:06, Konrad Dybcio wrote:
> On 6/30/26 9:15 AM, Krzysztof Kozlowski wrote:
>> On Mon, Jun 29, 2026 at 05:01:44PM +0400, George Moussalem wrote:
>>> +unevaluatedProperties: false
>>> +
>>> +examples:
>>> +  - |
>>> +    #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
>>> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
>>> +    #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
>>> +
>>> +    bluetooth {
>>
>> Don't send new versions while discussion is still going. I need to
>> repeat my question - what bus does that sit on?
>>
>> Device nodes represent real devices. Real devices sit on a bus, usually.
>> Do you have here a bus?
> 
> +Kathiravan would you know what the remoteproc-driven bluetooth is
> connected over on IPQ5018?

No need, this got resolved. I missed that this was merged with
remoteproc and remoteprocs we represent in top-level as it uses non-bus
way (APCS IPC or whatever its called). We could fix that and maybe this
should be a child of APCS... but maybe not and it feels like out of
scope of this patchset.

Best regards,
Krzysztof

Re: [PATCH v2 1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

[Krzysztof Kozlowski]

On 29/06/2026 15:01, George Moussalem via B4 Relay wrote:
> From: George Moussalem <george.moussalem@outlook.com>
> 
> Document the Qualcomm IPQ5018 Bluetooth controller.
> 
> Signed-off-by: George Moussalem <george.moussalem@outlook.com>
> ---
>  .../bindings/net/bluetooth/qcom,ipq5018-bt.yaml    | 86 ++++++++++++++++++++++
>  1 file changed, 86 insertions(+)

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

[PATCH v2 2/6] Bluetooth: btqca: Add IPQ5018 support

[George Moussalem via B4 Relay]

From: George Moussalem <george.moussalem@outlook.com>

Add the IPQ5018 SoC type and support for loading its firmware.

The firmware tested has been taken from GPL sources of various router
boards. Firmware files needed are:
- qca/bt_fw_patch.mbn
- qca/mpnv10.bin

Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
 drivers/bluetooth/btqca.c | 16 ++++++++++++++++
 drivers/bluetooth/btqca.h |  3 +++
 2 files changed, 19 insertions(+)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 04ebe290bc78..e136e91976cf 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -380,6 +380,9 @@ static int qca_tlv_check_data(struct hci_dev *hdev,
 		break;
 
 	case TLV_TYPE_NVM:
+		if (soc_type == QCA_IPQ5018)
+			break;
+
 		if (fw_size < sizeof(struct tlv_type_hdr))
 			return -EINVAL;
 
@@ -794,6 +797,9 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	else
 		rom_ver = ((soc_ver & 0x00000f00) >> 0x04) | (soc_ver & 0x0000000f);
 
+	if (soc_type == QCA_IPQ5018)
+		goto download_nvm;
+
 	if (soc_type == QCA_WCN6750)
 		qca_send_patch_config_cmd(hdev);
 
@@ -881,6 +887,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	if (soc_type == QCA_QCA2066 || soc_type == QCA_WCN7850)
 		qca_read_fw_board_id(hdev, &boardid);
 
+download_nvm:
 	/* Download NVM configuration */
 	config.type = TLV_TYPE_NVM;
 	if (firmware_name) {
@@ -939,6 +946,10 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
 				 "hmtnv", soc_type, ver, rom_ver, boardid);
 			break;
+		case QCA_IPQ5018:
+			snprintf(config.fwname, sizeof(config.fwname),
+				 "qca/mpnv%02x.bin", rom_ver);
+			break;
 		default:
 			snprintf(config.fwname, sizeof(config.fwname),
 				 "qca/nvm_%08x.bin", soc_ver);
@@ -958,6 +969,9 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 		return err;
 	}
 
+	if (soc_type == QCA_IPQ5018)
+		msleep(NVM_READY_DELAY_MS);
+
 	switch (soc_type) {
 	case QCA_QCA2066:
 	case QCA_QCA6390:
@@ -965,6 +979,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	case QCA_WCN6750:
 	case QCA_WCN6855:
 	case QCA_WCN7850:
+	case QCA_IPQ5018:
 		err = qca_disable_soc_logging(hdev);
 		if (err < 0)
 			return err;
@@ -1001,6 +1016,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	case QCA_WCN6750:
 	case QCA_WCN6855:
 	case QCA_WCN7850:
+	case QCA_IPQ5018:
 		/* get fw build info */
 		err = qca_read_fw_build_info(hdev);
 		if (err < 0)
diff --git a/drivers/bluetooth/btqca.h b/drivers/bluetooth/btqca.h
index 8f3c1b1c77b3..343cd62d1137 100644
--- a/drivers/bluetooth/btqca.h
+++ b/drivers/bluetooth/btqca.h
@@ -54,6 +54,8 @@
 #define QCA_HSP_GF_SOC_ID		0x1200
 #define QCA_HSP_GF_SOC_MASK		0x0000ff00
 
+#define NVM_READY_DELAY_MS		1500
+
 enum qca_baudrate {
 	QCA_BAUDRATE_115200	= 0,
 	QCA_BAUDRATE_57600,
@@ -158,6 +160,7 @@ enum qca_btsoc_type {
 	QCA_WCN6750,
 	QCA_WCN6855,
 	QCA_WCN7850,
+	QCA_IPQ5018,
 };
 
 #if IS_ENABLED(CONFIG_BT_QCA)

-- 
2.53.0

Re: [PATCH v2 2/6] Bluetooth: btqca: Add IPQ5018 support

[Bartosz Golaszewski]

On Mon, 29 Jun 2026 15:01:45 +0200, George Moussalem via B4 Relay
<devnull+george.moussalem.outlook.com@kernel.org> said:
> From: George Moussalem <george.moussalem@outlook.com>
>
> Add the IPQ5018 SoC type and support for loading its firmware.
>
> The firmware tested has been taken from GPL sources of various router
> boards. Firmware files needed are:
> - qca/bt_fw_patch.mbn
> - qca/mpnv10.bin
>
> Signed-off-by: George Moussalem <george.moussalem@outlook.com>
> ---

Acked-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>

[PATCH v2 3/6] firmware: qcom: scm: Add support for setting Bluetooth power modes

[George Moussalem via B4 Relay]

From: George Moussalem <george.moussalem@outlook.com>

The Bluetooth subsystem (BTSS) on the IPQ5018 SoC supports setting power
modes which are required to be configured through a Secure Channel
Manager (SCM) call to TrustZone. However, not all Trusted Execution
Environment (QSEE) images support this call, so first check if the call
is available.

Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
 drivers/firmware/qcom/qcom_scm.c       | 49 ++++++++++++++++++++++++++++++++++
 drivers/firmware/qcom/qcom_scm.h       |  1 +
 include/linux/firmware/qcom/qcom_scm.h |  1 +
 3 files changed, 51 insertions(+)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index 6b601a4b89db..e26f54e5033b 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -1094,6 +1094,55 @@ bool qcom_scm_pas_supported(u32 pas_id)
 }
 EXPORT_SYMBOL_GPL(qcom_scm_pas_supported);
 
+static int __qcom_scm_pas_set_bluetooth_power_mode(u32 pas_id, u32 val)
+{
+	struct qcom_scm_desc desc = {
+		.svc = QCOM_SCM_SVC_PIL,
+		.cmd = QCOM_SCM_PIL_PAS_BT_PWR_MODE,
+		.arginfo = QCOM_SCM_ARGS(2),
+		.args[0] = pas_id,
+		.args[1] = val,
+		.owner = ARM_SMCCC_OWNER_SIP,
+	};
+	struct qcom_scm_res res;
+	int ret;
+
+	ret = qcom_scm_clk_enable();
+	if (ret)
+		return ret;
+
+	ret = qcom_scm_bw_enable();
+	if (ret)
+		goto disable_clk;
+
+	ret = qcom_scm_call(__scm->dev, &desc, &res);
+	qcom_scm_bw_disable();
+
+disable_clk:
+	qcom_scm_clk_disable();
+
+	return ret ? : res.result[0];
+}
+
+/**
+ * qcom_scm_pas_set_bluetooth_power_mode() - Configure power optimization mode
+ *					     for the Bluetooth subsystem (BTSS)
+ * @pas_id:	peripheral authentication service id
+ * @val:	0x0 for normal operation, 0x4 for ECO mode
+ *
+ * Return: 0 on success, negative errno on failure.
+ * Returns -EOPNOTSUPP if the firmware configuration call is unavailable.
+ */
+int qcom_scm_pas_set_bluetooth_power_mode(u32 pas_id, u32 val)
+{
+	if (!__qcom_scm_is_call_available(__scm->dev, QCOM_SCM_SVC_PIL,
+					  QCOM_SCM_PIL_PAS_BT_PWR_MODE))
+		return -EOPNOTSUPP;
+
+	return __qcom_scm_pas_set_bluetooth_power_mode(pas_id, val);
+}
+EXPORT_SYMBOL_GPL(qcom_scm_pas_set_bluetooth_power_mode);
+
 static int __qcom_scm_pas_mss_reset(struct device *dev, bool reset)
 {
 	struct qcom_scm_desc desc = {
diff --git a/drivers/firmware/qcom/qcom_scm.h b/drivers/firmware/qcom/qcom_scm.h
index caab80a73e17..5579df5a2aca 100644
--- a/drivers/firmware/qcom/qcom_scm.h
+++ b/drivers/firmware/qcom/qcom_scm.h
@@ -105,6 +105,7 @@ int qcom_scm_shm_bridge_enable(struct device *scm_dev);
 #define QCOM_SCM_PIL_PAS_SHUTDOWN	0x06
 #define QCOM_SCM_PIL_PAS_IS_SUPPORTED	0x07
 #define QCOM_SCM_PIL_PAS_MSS_RESET	0x0a
+#define QCOM_SCM_PIL_PAS_BT_PWR_MODE	0x21
 #define QCOM_SCM_PIL_PAS_GET_RSCTABLE	0x21
 
 #define QCOM_SCM_SVC_IO			0x05
diff --git a/include/linux/firmware/qcom/qcom_scm.h b/include/linux/firmware/qcom/qcom_scm.h
index 5747bd191bf1..76de4b69580b 100644
--- a/include/linux/firmware/qcom/qcom_scm.h
+++ b/include/linux/firmware/qcom/qcom_scm.h
@@ -93,6 +93,7 @@ struct resource_table *qcom_scm_pas_get_rsc_table(struct qcom_scm_pas_context *c
 						  size_t *output_rt_size);
 
 int qcom_scm_pas_prepare_and_auth_reset(struct qcom_scm_pas_context *ctx);
+int qcom_scm_pas_set_bluetooth_power_mode(u32 pas_id, u32 val);
 
 int qcom_scm_io_readl(phys_addr_t addr, unsigned int *val);
 int qcom_scm_io_writel(phys_addr_t addr, unsigned int val);

-- 
2.53.0

Re: [PATCH v2 3/6] firmware: qcom: scm: Add support for setting Bluetooth power modes

[Bartosz Golaszewski]

On Mon, 29 Jun 2026 15:01:46 +0200, George Moussalem via B4 Relay
<devnull+george.moussalem.outlook.com@kernel.org> said:
> From: George Moussalem <george.moussalem@outlook.com>
>
> The Bluetooth subsystem (BTSS) on the IPQ5018 SoC supports setting power
> modes which are required to be configured through a Secure Channel
> Manager (SCM) call to TrustZone. However, not all Trusted Execution
> Environment (QSEE) images support this call, so first check if the call
> is available.
>
> Signed-off-by: George Moussalem <george.moussalem@outlook.com>
> ---

Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>

Re: [PATCH v2 3/6] firmware: qcom: scm: Add support for setting Bluetooth power modes

[Konrad Dybcio]

On 6/29/26 3:01 PM, George Moussalem via B4 Relay wrote:
> From: George Moussalem <george.moussalem@outlook.com>
> 
> The Bluetooth subsystem (BTSS) on the IPQ5018 SoC supports setting power
> modes which are required to be configured through a Secure Channel
> Manager (SCM) call to TrustZone. However, not all Trusted Execution
> Environment (QSEE) images support this call, so first check if the call
> is available.
> 
> Signed-off-by: George Moussalem <george.moussalem@outlook.com>
> ---

I'm amazed changing this setting is a secure operation

[...]

> +/**
> + * qcom_scm_pas_set_bluetooth_power_mode() - Configure power optimization mode
> + *					     for the Bluetooth subsystem (BTSS)
> + * @pas_id:	peripheral authentication service id
> + * @val:	0x0 for normal operation, 0x4 for ECO mode

If there's just two values, maybe we should make this take a `bool eco_mode`?

> + *
> + * Return: 0 on success, negative errno on failure.
> + * Returns -EOPNOTSUPP if the firmware configuration call is unavailable.
> + */
> +int qcom_scm_pas_set_bluetooth_power_mode(u32 pas_id, u32 val)
> +{
> +	if (!__qcom_scm_is_call_available(__scm->dev, QCOM_SCM_SVC_PIL,
> +					  QCOM_SCM_PIL_PAS_BT_PWR_MODE))
> +		return -EOPNOTSUPP;
> +
> +	return __qcom_scm_pas_set_bluetooth_power_mode(pas_id, val);

Let's just inline the whole definition here - it's single-use anyway

Konrad

Re: [PATCH v2 3/6] firmware: qcom: scm: Add support for setting Bluetooth power modes

[George Moussalem]

On 7/1/26 14:40, Konrad Dybcio wrote:
> On 6/29/26 3:01 PM, George Moussalem via B4 Relay wrote:
>> From: George Moussalem <george.moussalem@outlook.com>
>>
>> The Bluetooth subsystem (BTSS) on the IPQ5018 SoC supports setting power
>> modes which are required to be configured through a Secure Channel
>> Manager (SCM) call to TrustZone. However, not all Trusted Execution
>> Environment (QSEE) images support this call, so first check if the call
>> is available.
>>
>> Signed-off-by: George Moussalem <george.moussalem@outlook.com>
>> ---
> 
> I'm amazed changing this setting is a secure operation
> 
> [...]
> 
>> +/**
>> + * qcom_scm_pas_set_bluetooth_power_mode() - Configure power optimization mode
>> + *					     for the Bluetooth subsystem (BTSS)
>> + * @pas_id:	peripheral authentication service id
>> + * @val:	0x0 for normal operation, 0x4 for ECO mode
> 
> If there's just two values, maybe we should make this take a `bool eco_mode`?

that was the direction I was going in initially but then thought that
there may be more (undocumented) power modes I'm unaware off so changed
it to u32. I'll change it back to bool.

> 
>> + *
>> + * Return: 0 on success, negative errno on failure.
>> + * Returns -EOPNOTSUPP if the firmware configuration call is unavailable.
>> + */
>> +int qcom_scm_pas_set_bluetooth_power_mode(u32 pas_id, u32 val)
>> +{
>> +	if (!__qcom_scm_is_call_available(__scm->dev, QCOM_SCM_SVC_PIL,
>> +					  QCOM_SCM_PIL_PAS_BT_PWR_MODE))
>> +		return -EOPNOTSUPP;
>> +
>> +	return __qcom_scm_pas_set_bluetooth_power_mode(pas_id, val);
> 
> Let's just inline the whole definition here - it's single-use anyway

will update, thanks.

> 
> Konrad

Cheers,
George

Re: [PATCH v2 3/6] firmware: qcom: scm: Add support for setting Bluetooth power modes

[Konrad Dybcio]

On 7/1/26 3:15 PM, George Moussalem wrote:
> On 7/1/26 14:40, Konrad Dybcio wrote:
>> On 6/29/26 3:01 PM, George Moussalem via B4 Relay wrote:
>>> From: George Moussalem <george.moussalem@outlook.com>
>>>
>>> The Bluetooth subsystem (BTSS) on the IPQ5018 SoC supports setting power
>>> modes which are required to be configured through a Secure Channel
>>> Manager (SCM) call to TrustZone. However, not all Trusted Execution
>>> Environment (QSEE) images support this call, so first check if the call
>>> is available.
>>>
>>> Signed-off-by: George Moussalem <george.moussalem@outlook.com>
>>> ---
>>
>> I'm amazed changing this setting is a secure operation
>>
>> [...]
>>
>>> +/**
>>> + * qcom_scm_pas_set_bluetooth_power_mode() - Configure power optimization mode
>>> + *					     for the Bluetooth subsystem (BTSS)
>>> + * @pas_id:	peripheral authentication service id
>>> + * @val:	0x0 for normal operation, 0x4 for ECO mode
>>
>> If there's just two values, maybe we should make this take a `bool eco_mode`?
> 
> that was the direction I was going in initially but then thought that
> there may be more (undocumented) power modes I'm unaware off so changed
> it to u32. I'll change it back to bool.

We can always change back if needed

Konrad

[PATCH v2 4/6] Bluetooth: Introduce Qualcomm IPQ5018 IPC based HCI driver

[George Moussalem via B4 Relay]

From: George Moussalem <george.moussalem@outlook.com>

Add support for the Bluetooth controller found in the IPQ5018 SoC.
This driver implements firmware loading and the transport layer between
the HCI core and the Bluetooth controller.

The firmware is loaded by the host into the dedicated reserved memory
carveout and authenticated by TrustZone. A Secure Channel Manager (SCM)
call safely brings the peripheral core out of reset.

A shared memory ring buffer topology handles runtime data frame
transport between the host APSS and the controller.

An outgoing APCS IPC bit and an incoming GIC interrupt handle host/guest
signaling.

Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
 drivers/bluetooth/Kconfig     |   11 +
 drivers/bluetooth/Makefile    |    1 +
 drivers/bluetooth/btqcomipc.c | 1052 +++++++++++++++++++++++++++++++++++++++++
 3 files changed, 1064 insertions(+)

diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
index 4e8c24d757e9..c9785f43c87c 100644
--- a/drivers/bluetooth/Kconfig
+++ b/drivers/bluetooth/Kconfig
@@ -413,6 +413,17 @@ config BT_MTKUART
 	  Say Y here to compile support for MediaTek Bluetooth UART devices
 	  into the kernel or say M to compile it as module (btmtkuart).
 
+config BT_QCOMIPC
+	tristate "Qualcomm IPQ5018 IPC based HCI support"
+	select BT_QCA
+	help
+	  Qualcomm IPQ5018 IPC based HCI driver.
+	  This driver is used to load firmware and bridge HCI data onto shared
+	  memory between the host and the Bluetooth controller.
+
+	  Say Y here to compile support for HCI over Qualcomm IPC into the
+	  kernel or say M to compile as a module.
+
 config BT_QCOMSMD
 	tristate "Qualcomm SMD based HCI support"
 	depends on RPMSG || (COMPILE_TEST && RPMSG=n)
diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
index e6b1c1180d1d..05f19047bed0 100644
--- a/drivers/bluetooth/Makefile
+++ b/drivers/bluetooth/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_BT_MRVL)		+= btmrvl.o
 obj-$(CONFIG_BT_MRVL_SDIO)	+= btmrvl_sdio.o
 obj-$(CONFIG_BT_MTKSDIO)	+= btmtksdio.o
 obj-$(CONFIG_BT_MTKUART)	+= btmtkuart.o
+obj-$(CONFIG_BT_QCOMIPC)	+= btqcomipc.o
 obj-$(CONFIG_BT_QCOMSMD)	+= btqcomsmd.o
 obj-$(CONFIG_BT_BCM)		+= btbcm.o
 obj-$(CONFIG_BT_RTL)		+= btrtl.o
diff --git a/drivers/bluetooth/btqcomipc.c b/drivers/bluetooth/btqcomipc.c
new file mode 100644
index 000000000000..16bc59e4edae
--- /dev/null
+++ b/drivers/bluetooth/btqcomipc.c
@@ -0,0 +1,1052 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2020 The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/elf.h>
+#include <linux/firmware.h>
+#include <linux/firmware/qcom/qcom_scm.h>
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_reserved_mem.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+#include <linux/skbuff.h>
+#include <linux/slab.h>
+#include <linux/soc/qcom/mdt_loader.h>
+#include <linux/types.h>
+#include <linux/workqueue.h>
+
+#include <net/bluetooth/bluetooth.h>
+#include <net/bluetooth/hci_core.h>
+
+#include "btqca.h"
+
+/** Message header format.
+ *
+ *        ----------------------------------------------------------------
+ * BitPos |    15    | 14 | 13 | 12 | 11 | 10 |  9  |  8  |    7 - 0     |
+ *         ---------------------------------------------------------------
+ * Field  | long_msg |ACK |        RFU        |  pkt_type |    cmd       |
+ *        ----------------------------------------------------------------
+ *
+ * - long_msg   : If set, indicates that the payload is larger than the
+ *                IPC_MSG_PLD_SZ. The payload instead contains a pointer to the
+ *                long message buffer in the shared BTSS memory space.
+ *
+ * - ACK        : Set if sending ACK if required by sending acknowledegement
+ *                to sender i.e. send an ack IPC interrupt if set.
+ *
+ * - RFU        : Reserved for future use.
+ *
+ * - pkt_type   : IPC Packet Type
+ *
+ * - cmd        : Contains unique command ID
+ */
+
+#define IPC_MSG_HDR_SZ		4
+#define IPC_MSG_PLD_SZ		40
+#define IPC_TOTAL_MSG_SZ	(IPC_MSG_HDR_SZ + IPC_MSG_PLD_SZ)
+
+/* Message Header */
+#define IPC_HDR_LONG_MSG	BIT(15)
+#define IPC_HDR_REQ_ACK		BIT(14)
+#define IPC_HDR_PKT_TYPE_MASK	GENMASK(9, 8)
+#define  IPC_HDR_PKT_TYPE_CUST	0
+#define  IPC_HDR_PKT_TYPE_HCI	1
+#define  IPC_HDR_PKT_TYPE_AUDIO	2
+#define  IPC_HDR_PKT_TYPE_RFU	3
+#define IPC_HDR_CMD_MASK	GENMASK(7, 0)
+
+#define IPC_CMD_STOP		1
+#define IPC_CMD_SWITCH_TO_UART	2
+#define IPC_CMD_PREPARE_DUMP	3
+#define IPC_CMD_COLLECT_DUMP	4
+#define IPC_CMD_START		5
+
+#define IPC_TX_QSIZE		32
+
+#define	TO_APPS_ADDR(a)		(desc->mem_region + (int)(uintptr_t)a)
+#define	TO_BT_ADDR(a)		(a - desc->mem_region)
+#define IPC_LBUF_SZ(w, x, y, z)	(((TO_BT_ADDR((void *)w) + w->x) - w->y) / w->z)
+
+#define	GET_NO_OF_BLOCKS(a, b) ((a + b - 1) / b)
+
+#define GET_RX_INDEX_FROM_BUF(x, y)	((x - desc->rx_ctxt->lring_buf) / y)
+
+#define GET_TX_INDEX_FROM_BUF(x, y)	((x - desc->tx_ctxt->lring_buf) / y)
+
+#define IS_RX_MEM_NON_CONTIGIOUS(buf, len, sz)		\
+	((buf + len) > (desc->rx_ctxt->lring_buf +	\
+	(sz * desc->rx_ctxt->lmsg_buf_cnt)))
+
+#define BTSS_PAS_ID		0xc
+
+#define BTSS_PWR_STATE_ACTIVE	0x0
+#define BTSS_PWR_STATE_ECO	0x4
+#define BTSS_PWR_CTRL_DELAY_MS	50
+
+struct long_msg_info {
+	__le16 smsg_free_cnt;
+	__le16 lmsg_free_cnt;
+	u8 ridx;
+	u8 widx;
+} __packed;
+
+struct ipc_aux_ptr {
+	__le32 len;
+	__le32 buf;
+} __packed;
+
+struct ring_buffer {
+	__le16 msg_hdr;
+	__le16 len;
+	union {
+		u8 smsg_data[IPC_MSG_PLD_SZ];
+		__le32 lmsg_data;
+	} payload;
+} __packed;
+
+struct ring_buffer_info {
+	__le32 rbuf;
+	u8 ring_buf_cnt;
+	u8 ridx;
+	u8 widx;
+	u8 tidx;
+	__le32 next;
+} __packed;
+
+struct context_info {
+	__le16 total_size;
+	u8 lmsg_buf_cnt;
+	u8 smsg_buf_cnt;
+	struct ring_buffer_info sring_buf_info;
+	__le32 sring_buf;
+	__le32 lring_buf;
+	__le32 reserved;
+} __packed;
+
+struct qcom_btss {
+	struct device *dev;
+	struct hci_dev *hdev;
+
+	struct regmap *regmap;
+	u32 offset;
+	u32 bit;
+	int irq;
+
+	const char *firmware;
+	void *mem_region;
+	phys_addr_t mem_phys;
+	phys_addr_t mem_reloc;
+	size_t mem_size;
+
+	struct sk_buff_head tx_q;
+	struct workqueue_struct *wq;
+	struct work_struct work;
+	wait_queue_head_t wait_q;
+	spinlock_t lock;
+
+	struct context_info *tx_ctxt;
+	struct context_info *rx_ctxt;
+	struct long_msg_info lmsg_ctxt;
+
+	bool running;
+};
+
+static void btqcomipc_update_stats(struct hci_dev *hdev, struct sk_buff *skb);
+
+static void *btss_alloc_lmsg(struct qcom_btss *desc, u32 len,
+			     struct ipc_aux_ptr *aux_ptr, bool *is_lbuf_full)
+{
+	struct device *dev = desc->dev;
+	u8 idx, blks, blks_consumed;
+	void *ret_ptr;
+	u32 lsz;
+
+	if (desc->tx_ctxt->lring_buf == 0) {
+		dev_err(dev, "no long message buffer initialized\n");
+		return ERR_PTR(-ENODEV);
+	}
+
+	lsz = IPC_LBUF_SZ(desc->tx_ctxt, total_size, lring_buf, lmsg_buf_cnt);
+	blks = GET_NO_OF_BLOCKS(len, lsz);
+
+	if (!desc->lmsg_ctxt.lmsg_free_cnt ||
+			(blks > desc->lmsg_ctxt.lmsg_free_cnt))
+		return ERR_PTR(-EAGAIN);
+
+	idx = desc->lmsg_ctxt.widx;
+
+	if ((desc->lmsg_ctxt.widx + blks) > desc->tx_ctxt->lmsg_buf_cnt) {
+		blks_consumed = desc->tx_ctxt->lmsg_buf_cnt - idx;
+		aux_ptr->len = len - (blks_consumed * lsz);
+		aux_ptr->buf = desc->tx_ctxt->lring_buf;
+	}
+
+	desc->lmsg_ctxt.widx = (desc->lmsg_ctxt.widx + blks) %
+		desc->tx_ctxt->lmsg_buf_cnt;
+
+	desc->lmsg_ctxt.lmsg_free_cnt -= blks;
+
+	if (desc->lmsg_ctxt.lmsg_free_cnt <=
+			((desc->tx_ctxt->lmsg_buf_cnt * 20) / 100))
+		*is_lbuf_full = true;
+
+	ret_ptr = TO_APPS_ADDR(desc->tx_ctxt->lring_buf) + (idx * lsz);
+
+	return ret_ptr;
+}
+
+static struct ring_buffer_info *btss_get_tx_rbuf(struct qcom_btss *desc,
+						 bool *is_sbuf_full)
+{
+	u8 idx;
+	struct ring_buffer_info *rinfo;
+
+	for (rinfo = &(desc->tx_ctxt->sring_buf_info);	rinfo != NULL;
+		rinfo = (struct ring_buffer_info *)(uintptr_t)(rinfo->next)) {
+		idx = (rinfo->widx + 1) % (desc->tx_ctxt->smsg_buf_cnt);
+
+		if (idx != rinfo->tidx) {
+			desc->lmsg_ctxt.smsg_free_cnt--;
+
+			if (desc->lmsg_ctxt.smsg_free_cnt <=
+				((desc->tx_ctxt->smsg_buf_cnt * 20) / 100))
+				*is_sbuf_full = true;
+
+			return rinfo;
+		}
+	}
+
+	return ERR_PTR(-EAGAIN);
+}
+
+static int btss_send(struct qcom_btss *desc, u16 msg_hdr,
+		     struct sk_buff *skb)
+{
+	struct hci_dev *hdev = desc->hdev;
+	struct ring_buffer_info *rinfo;
+	struct ipc_aux_ptr aux_ptr;
+	struct ring_buffer *rbuf;
+	bool is_lbuf_full = false;
+	bool is_sbuf_full = false;
+	u16 hdr = msg_hdr;
+	void *ptr_buf;
+	u32 len;
+
+	/* Account for HCI packet type as it's not included in the skb payload */
+	len = (skb) ? skb->len + 1 : 0;
+	memset(&aux_ptr, 0, sizeof(struct ipc_aux_ptr));
+
+	if (len > IPC_MSG_PLD_SZ) {
+		hdr |= IPC_HDR_LONG_MSG;
+
+		ptr_buf = btss_alloc_lmsg(desc, len,
+					  &aux_ptr, &is_lbuf_full);
+		if (IS_ERR(ptr_buf)) {
+			bt_dev_err(hdev, "TX long buffers full");
+			hdev->stat.err_tx++;
+			return PTR_ERR(ptr_buf);
+		}
+	}
+
+	rinfo = btss_get_tx_rbuf(desc, &is_sbuf_full);
+	if (IS_ERR(rinfo)) {
+		bt_dev_err(hdev, "TX short buffers full");
+		hdev->stat.err_tx++;
+		return PTR_ERR(rinfo);
+	}
+
+	rbuf = &((struct ring_buffer *)(TO_APPS_ADDR(rinfo->rbuf)))[rinfo->widx];
+
+	if (!skb)
+		goto complete_tx;
+
+	if (len > IPC_MSG_PLD_SZ)
+		rbuf->payload.lmsg_data = cpu_to_le32(TO_BT_ADDR(ptr_buf));
+	else
+		ptr_buf = rbuf->payload.smsg_data;
+
+	/* if it's a short message, the aux len and buf are NULL */
+	memcpy_toio(ptr_buf, &hci_skb_pkt_type(skb), 1);
+	memcpy_toio((u8 *)ptr_buf + 1, skb->data, skb->len - aux_ptr.len);
+	if (aux_ptr.buf) {
+		memcpy_toio(TO_APPS_ADDR(aux_ptr.buf),
+			    (skb->data + (skb->len - aux_ptr.len)),
+			    aux_ptr.len);
+	}
+
+	/*
+	 * if free buffer count is low, send ACK request to signal to the
+	 * firmware to process and free up queued buffers in the TX ring.
+	 */
+	if (is_sbuf_full || is_lbuf_full)
+		hdr |= IPC_HDR_REQ_ACK;
+
+complete_tx:
+	rbuf->msg_hdr = cpu_to_le16(hdr);
+	rbuf->len = cpu_to_le16(len);
+
+	rinfo->widx = (rinfo->widx + 1) % desc->tx_ctxt->smsg_buf_cnt;
+
+	regmap_set_bits(desc->regmap, desc->offset, BIT(desc->bit));
+
+	return 0;
+}
+
+static void btss_process_tx_queue(struct qcom_btss *desc)
+{
+	struct sk_buff *skb;
+	u16 hdr;
+	int ret;
+
+	while ((skb = skb_dequeue(&desc->tx_q))) {
+		hdr = FIELD_PREP(IPC_HDR_PKT_TYPE_MASK, IPC_HDR_PKT_TYPE_HCI);
+
+		ret = btss_send(desc, hdr, skb);
+		if (ret) {
+			bt_dev_err(desc->hdev, "Failed to send message");
+			skb_queue_head(&desc->tx_q, skb);
+			break;
+		}
+
+		btqcomipc_update_stats(desc->hdev, skb);
+		kfree_skb(skb);
+	}
+}
+
+static void btss_free_lmsg(struct qcom_btss *desc, u32 lmsg, u16 len)
+{
+	u8 idx;
+	u8 blks;
+	u32 lsz = IPC_LBUF_SZ(desc->tx_ctxt, total_size, lring_buf,
+				   lmsg_buf_cnt);
+
+	idx = GET_TX_INDEX_FROM_BUF(lmsg, lsz);
+
+	if (idx != desc->lmsg_ctxt.ridx)
+		return;
+
+	blks = GET_NO_OF_BLOCKS(len, lsz);
+
+	desc->lmsg_ctxt.ridx  = (desc->lmsg_ctxt.ridx  + blks) %
+		desc->tx_ctxt->lmsg_buf_cnt;
+
+	desc->lmsg_ctxt.lmsg_free_cnt += blks;
+}
+
+static int btss_recv_cust_frame(struct qcom_btss *desc, u8 cmd)
+{
+	u16 msg_hdr = 0;
+	int ret;
+
+	switch (cmd) {
+	case IPC_CMD_STOP:
+		spin_unlock(&desc->lock);
+		ret = qcom_scm_pas_set_bluetooth_power_mode(BTSS_PAS_ID,
+							    BTSS_PWR_STATE_ECO);
+		spin_lock(&desc->lock);
+		if (ret && ret != -EOPNOTSUPP) {
+			bt_dev_err(desc->hdev,
+				   "Failed to apply BTSS power-save mode: %d",
+				   ret);
+			return ret;
+		}
+
+		WRITE_ONCE(desc->running, false);
+
+		msg_hdr |= cmd;
+		ret = btss_send(desc, msg_hdr, NULL);
+		if (ret)
+			bt_dev_err(desc->hdev,
+				   "Failed to send control message");
+		break;
+	case IPC_CMD_START:
+		spin_unlock(&desc->lock);
+		ret = qcom_scm_pas_set_bluetooth_power_mode(BTSS_PAS_ID,
+							    BTSS_PWR_STATE_ACTIVE);
+		spin_lock(&desc->lock);
+		if (ret && ret != -EOPNOTSUPP) {
+			bt_dev_err(desc->hdev,
+				   "Failed to apply BTSS active power mode: %d",
+				   ret);
+			return ret;
+		}
+
+		desc->tx_ctxt = (struct context_info *)((void *)desc->rx_ctxt +
+				le16_to_cpu(desc->rx_ctxt->total_size));
+		desc->lmsg_ctxt.widx = 0;
+		desc->lmsg_ctxt.ridx = 0;
+		desc->lmsg_ctxt.smsg_free_cnt = desc->tx_ctxt->smsg_buf_cnt;
+		desc->lmsg_ctxt.lmsg_free_cnt = desc->tx_ctxt->lmsg_buf_cnt;
+		WRITE_ONCE(desc->running, true);
+		wake_up(&desc->wait_q);
+		break;
+	default:
+		bt_dev_err(desc->hdev, "Unsupported CMD ID: %u", cmd);
+		return -EOPNOTSUPP;
+	}
+
+	return 0;
+}
+
+static inline int btss_recv_hci_frame(struct qcom_btss *desc, const u8 *data,
+				      size_t len)
+{
+	unsigned char pkt_type;
+	struct sk_buff *skb;
+	size_t pkt_len;
+
+	if (len < 1)
+		return -EPROTO;
+
+	pkt_type = data[0];
+
+	switch (pkt_type) {
+	case HCI_EVENT_PKT:
+	{
+		if (len < 1 + HCI_EVENT_HDR_SIZE)
+			return -EILSEQ;
+		struct hci_event_hdr *hdr = (struct hci_event_hdr *)(data + 1);
+
+		pkt_len = HCI_EVENT_HDR_SIZE + hdr->plen;
+		break;
+	}
+	case HCI_COMMAND_PKT: {
+		if (len < 1 + HCI_COMMAND_HDR_SIZE)
+			return -EILSEQ;
+		struct hci_command_hdr *hdr = (struct hci_command_hdr *)(data + 1);
+
+		pkt_len = HCI_COMMAND_HDR_SIZE + le16_to_cpu(hdr->plen);
+		break;
+	}
+	case HCI_ACLDATA_PKT:
+	{
+		if (len < 1 + HCI_ACL_HDR_SIZE)
+			return -EILSEQ;
+		struct hci_acl_hdr *hdr = (struct hci_acl_hdr *)(data + 1);
+
+		pkt_len = HCI_ACL_HDR_SIZE + le16_to_cpu(hdr->dlen);
+		break;
+	}
+	case HCI_SCODATA_PKT:
+	{
+		if (len < 1 + HCI_SCO_HDR_SIZE)
+			return -EILSEQ;
+		struct hci_sco_hdr *hdr = (struct hci_sco_hdr *)(data + 1);
+
+		pkt_len = HCI_SCO_HDR_SIZE + hdr->dlen;
+		break;
+	}
+	default:
+		return -EPROTO;
+	}
+
+	if (pkt_len + 1 > len)
+		return -EINVAL;
+
+	skb = bt_skb_alloc(pkt_len, GFP_ATOMIC);
+	if (!skb) {
+		desc->hdev->stat.err_rx++;
+		return -ENOMEM;
+	}
+
+	skb->dev = (void *)desc->hdev;
+	hci_skb_pkt_type(skb) = pkt_type;
+	skb_put_data(skb, data + 1, pkt_len);
+
+	hci_recv_frame(desc->hdev, skb);
+	desc->hdev->stat.byte_rx += pkt_len;
+
+	return 0;
+}
+
+static inline int btss_process_rx(struct qcom_btss *desc,
+				  struct ring_buffer_info *rinfo,
+				  bool *ack, u8 *rx_count)
+{
+	u8 ridx, lbuf_idx, blks_consumed, pkt_type, cmd;
+	struct ipc_aux_ptr aux_ptr;
+	struct ring_buffer *rbuf;
+	uint8_t *rxbuf = NULL;
+	unsigned char *buf;
+	u32 lsz;
+	int ret;
+
+	ridx = rinfo->ridx;
+
+	while (ridx != rinfo->widx) {
+		memset(&aux_ptr, 0, sizeof(struct ipc_aux_ptr));
+
+		rbuf = &((struct ring_buffer *)(TO_APPS_ADDR(rinfo->rbuf)))[ridx];
+
+		if (rbuf->msg_hdr & IPC_HDR_LONG_MSG) {
+			rxbuf = TO_APPS_ADDR(rbuf->payload.lmsg_data);
+			lsz = IPC_LBUF_SZ(desc->rx_ctxt, total_size, lring_buf,
+				   lmsg_buf_cnt);
+
+			if (IS_RX_MEM_NON_CONTIGIOUS(rbuf->payload.lmsg_data,
+						     rbuf->len, lsz)) {
+				lbuf_idx = GET_RX_INDEX_FROM_BUF(
+						rbuf->payload.lmsg_data, lsz);
+
+				blks_consumed = desc->rx_ctxt->lmsg_buf_cnt -
+					lbuf_idx;
+				aux_ptr.len = rbuf->len - (blks_consumed * lsz);
+				aux_ptr.buf = desc->rx_ctxt->lring_buf;
+			}
+		} else {
+			rxbuf = rbuf->payload.smsg_data;
+		}
+
+		*ack = (rbuf->msg_hdr & IPC_HDR_REQ_ACK);
+
+		pkt_type = FIELD_GET(IPC_HDR_PKT_TYPE_MASK, rbuf->msg_hdr);
+
+		switch (pkt_type) {
+		case IPC_HDR_PKT_TYPE_HCI:
+			buf = kmalloc(rbuf->len, GFP_ATOMIC);
+			if (!buf) {
+				rinfo->ridx = ridx;
+				return -ENOMEM;
+			}
+
+			memcpy_fromio(buf, rxbuf, rbuf->len - aux_ptr.len);
+
+			if (aux_ptr.buf)
+				memcpy_fromio(buf + (rbuf->len - aux_ptr.len),
+					      TO_APPS_ADDR(aux_ptr.buf),
+					      aux_ptr.len);
+
+			ret = btss_recv_hci_frame(desc, buf, rbuf->len);
+			if (ret)
+				bt_dev_err(desc->hdev,
+					   "Failed to process HCI frame: %d",
+					   ret);
+			kfree(buf);
+			break;
+		case IPC_HDR_PKT_TYPE_CUST:
+			cmd = FIELD_GET(IPC_HDR_CMD_MASK, rbuf->msg_hdr);
+			ret = btss_recv_cust_frame(desc, cmd);
+			if (ret)
+				bt_dev_warn(desc->hdev,
+					    "Failed to process custom frame: %d",
+					    ret);
+			break;
+		default:
+			break;
+		}
+
+		ridx = (ridx + 1) % rinfo->ring_buf_cnt;
+
+		if (rx_count)
+			(*rx_count)++;
+
+		rinfo->ridx = ridx;
+	}
+
+	return 0;
+}
+
+static void btss_process_ack(struct qcom_btss *desc)
+{
+	struct ring_buffer_info *rinfo;
+	struct ring_buffer *rbuf;
+	u8 tidx;
+
+	for (rinfo = &desc->tx_ctxt->sring_buf_info; rinfo != NULL;
+		rinfo = (struct ring_buffer_info *)(uintptr_t)(rinfo->next)) {
+		tidx = rinfo->tidx;
+		rbuf = (struct ring_buffer *)TO_APPS_ADDR(rinfo->rbuf);
+
+		while (tidx != rinfo->ridx) {
+			if (rbuf[tidx].msg_hdr & IPC_HDR_LONG_MSG) {
+				btss_free_lmsg(desc,
+					       rbuf[tidx].payload.lmsg_data,
+					       rbuf[tidx].len);
+			}
+
+			tidx = (tidx + 1) % desc->tx_ctxt->smsg_buf_cnt;
+			desc->lmsg_ctxt.smsg_free_cnt++;
+		}
+
+		rinfo->tidx = tidx;
+
+		btss_process_tx_queue(desc);
+	}
+}
+
+static void btss_worker(struct work_struct *work)
+{
+	struct qcom_btss *desc = container_of(work, struct qcom_btss, work);
+	struct ring_buffer_info *rinfo;
+	bool ack = false;
+	u32 offset;
+	int ret;
+
+	spin_lock(&desc->lock);
+
+	if (unlikely(!READ_ONCE(desc->running))) {
+		/*
+		 * FW sets offset of RX context info at the start of the memory
+		 * region upon boot
+		 */
+		offset = readl(desc->mem_region);
+		dev_dbg(desc->dev, "offset after firmware boot: 0x%08x\n",
+			offset);
+		desc->rx_ctxt = (struct context_info *)(desc->mem_region + offset);
+	} else {
+		btss_process_ack(desc);
+	}
+
+	for (rinfo = &(desc->rx_ctxt->sring_buf_info);
+	     rinfo != NULL;
+	     rinfo = (struct ring_buffer_info *)(uintptr_t)(rinfo->next)) {
+		ret = btss_process_rx(desc, rinfo, &ack,
+				      &desc->rx_ctxt->smsg_buf_cnt);
+		if (ret) {
+			bt_dev_err(desc->hdev,
+				   "Failed to process peer msgs: %d", ret);
+			goto spin_unlock;
+		}
+	}
+
+	if (ack)
+		regmap_set_bits(desc->regmap, desc->offset, BIT(desc->bit));
+
+spin_unlock:
+	spin_unlock(&desc->lock);
+}
+
+static irqreturn_t btss_irq_handler(int irq, void *data)
+{
+	struct qcom_btss *desc = data;
+
+	queue_work(desc->wq, &desc->work);
+
+	return IRQ_HANDLED;
+}
+
+static void btqcomipc_update_stats(struct hci_dev *hdev, struct sk_buff *skb)
+{
+	u8 pkt_type = hci_skb_pkt_type(skb);
+
+	hdev->stat.byte_tx += skb->len;
+	switch (pkt_type) {
+	case HCI_COMMAND_PKT:
+		hdev->stat.cmd_tx++;
+		break;
+	case HCI_ACLDATA_PKT:
+		hdev->stat.acl_tx++;
+		break;
+	case HCI_SCODATA_PKT:
+		hdev->stat.sco_tx++;
+		break;
+	default:
+		break;
+	}
+}
+
+static int btcomqipc_firmware_load(struct qcom_btss *desc)
+{
+	const struct elf32_phdr *phdrs;
+	const struct firmware *seg_fw;
+	const struct elf32_phdr *phdr;
+	const struct elf32_hdr *ehdr;
+	const struct firmware *fw;
+	int i, ret;
+
+	ret = request_firmware(&fw, desc->firmware, desc->dev);
+	if (ret) {
+		dev_err(desc->dev, "Failed to request firmware: %d\n",
+			ret);
+		return ret;
+	}
+
+	ehdr = (const struct elf32_hdr *)fw->data;
+	phdrs = (const struct elf32_phdr *)(ehdr + 1);
+
+	ret = qcom_mdt_pas_init(desc->dev, fw, desc->firmware,
+				BTSS_PAS_ID, desc->mem_phys, NULL);
+	if (ret) {
+		dev_err(desc->dev, "PAS init failed: %d\n", ret);
+		goto release_fw;
+	}
+
+	for (i = 0; i < ehdr->e_phnum; i++) {
+		char *seg_name __free(kfree) = kstrdup(desc->firmware,
+						       GFP_KERNEL);
+		if (!seg_name) {
+			ret = -ENOMEM;
+			goto release_fw;
+		}
+
+		phdr = &phdrs[i];
+
+		/* Only process valid loadable data segments */
+		if (phdr->p_type != PT_LOAD || !phdr->p_memsz)
+			continue;
+
+		if (phdr->p_vaddr + phdr->p_filesz > desc->mem_size) {
+			dev_err(desc->dev,
+				"Segment data exceeds the reserved memory area!\n");
+			goto release_fw;
+		}
+
+		/* Check if firmware is split across multiple segment files */
+		if (phdr->p_offset > fw->size ||
+		    phdr->p_offset + phdr->p_filesz > fw->size) {
+			sprintf(seg_name + strlen(seg_name) - 3, "b%02d", i);
+			ret = request_firmware(&seg_fw, seg_name,
+					       desc->dev);
+			if (ret) {
+				dev_err(desc->dev,
+					"Could not find split segment binary: %s\n",
+					seg_name);
+				goto release_fw;
+			}
+
+			/*
+			 * Use the virtual instead of the physical address as
+			 * the offset
+			 */
+			memcpy_toio(desc->mem_region + phdr->p_vaddr,
+				    seg_fw->data, phdr->p_filesz);
+
+			release_firmware(seg_fw);
+		} else {
+			memcpy_toio(desc->mem_region + phdr->p_vaddr,
+				    fw->data + phdr->p_offset, phdr->p_filesz);
+		}
+	}
+
+release_fw:
+	release_firmware(fw);
+	return ret;
+}
+
+static int btqcomipc_open(struct hci_dev *hdev)
+{
+	struct qcom_btss *desc = hci_get_drvdata(hdev);
+	int ret;
+
+	if (!qcom_scm_pas_supported(BTSS_PAS_ID)) {
+		bt_dev_err(hdev,
+			   "PAS is not available for peripheral: 0x%x",
+			   BTSS_PAS_ID);
+		return -ENODEV;
+	}
+
+	ret = btcomqipc_firmware_load(desc);
+	if (ret) {
+		bt_dev_err(hdev, "Failed to load firmware: %d", ret);
+		return ret;
+	}
+
+	/* Boot firmware */
+	ret = qcom_scm_pas_auth_and_reset(BTSS_PAS_ID);
+	if (ret) {
+		bt_dev_err(hdev, "Failed to boot firmware: %d", ret);
+		return ret;
+	}
+
+	msleep(BTSS_PWR_CTRL_DELAY_MS);
+	ret = wait_event_timeout(desc->wait_q, READ_ONCE(desc->running),
+				 msecs_to_jiffies(1000));
+
+	if (!ret) {
+		bt_dev_err(hdev, "Timeout waiting for BTSS start");
+		return -ETIMEDOUT;
+	}
+
+	return 0;
+}
+
+static int btqcomipc_close(struct hci_dev *hdev)
+{
+	int ret;
+
+	ret = qcom_scm_pas_shutdown(BTSS_PAS_ID);
+	if (ret) {
+		bt_dev_err(hdev, "Failed to stop firmware: %d", ret);
+		return ret;
+	}
+
+	msleep(BTSS_PWR_CTRL_DELAY_MS);
+
+	return 0;
+}
+
+static int btqcomipc_setup(struct hci_dev *hdev)
+{
+	struct qca_btsoc_version ver;
+	int ret;
+
+	/*
+	 * Enable controller to do both LE scan and BR/EDR inquiry
+	 * simultaneously.
+	 */
+	hci_set_quirk(hdev, HCI_QUIRK_SIMULTANEOUS_DISCOVERY);
+
+	/*
+	 * Enable NON_PERSISTENT_SETUP QUIRK to ensure to execute
+	 * setup for every hci up.
+	 */
+	hci_set_quirk(hdev, HCI_QUIRK_NON_PERSISTENT_SETUP);
+	ret = qca_read_soc_version(hdev, &ver, QCA_IPQ5018);
+	if (ret)
+		return -EINVAL;
+
+	ret = qca_uart_setup(hdev, 0, QCA_IPQ5018, ver, NULL);
+	if (ret) {
+		bt_dev_err(hdev, "Failed to setup UART: %d\n", ret);
+		return ret;
+	}
+
+	bt_dev_info(hdev, "QCA Build Info: %s", hdev->fw_info);
+
+	/* Obtain and set BD address from NVMEM cell */
+	hci_set_quirk(hdev, HCI_QUIRK_USE_BDADDR_NVMEM);
+	hci_set_quirk(hdev, HCI_QUIRK_BDADDR_NVMEM_BE);
+
+	return 0;
+}
+
+static int btqcomipc_send(struct hci_dev *hdev, struct sk_buff *skb)
+{
+	u16 hdr = FIELD_PREP(IPC_HDR_PKT_TYPE_MASK, IPC_HDR_PKT_TYPE_HCI);
+	struct qcom_btss *desc = hci_get_drvdata(hdev);
+	int ret;
+
+	if (unlikely(!READ_ONCE(desc->running))) {
+		bt_dev_err(hdev,
+			   "BTSS not initialized, failed to send message");
+		ret = -ENODEV;
+		goto free_skb;
+	}
+
+	ret = btss_send(desc, hdr, skb);
+	if (ret) {
+		if (ret == -EAGAIN) {
+			if (skb_queue_len(&desc->tx_q) >= IPC_TX_QSIZE) {
+				bt_dev_err(hdev,
+					   "TX queue full, dropping message");
+				hdev->stat.err_tx++;
+				ret = -ENOBUFS;
+			} else {
+				skb_queue_tail(&desc->tx_q, skb);
+				return 0;
+			}
+		} else {
+			bt_dev_err(hdev, "Failed to send message: %d", ret);
+			hdev->stat.err_tx++;
+		}
+	}
+
+	btqcomipc_update_stats(desc->hdev, skb);
+
+free_skb:
+	kfree_skb(skb);
+
+	return ret;
+}
+
+static int btqcomipc_flush(struct hci_dev *hdev)
+{
+	struct qcom_btss *desc = hci_get_drvdata(hdev);
+
+	skb_queue_purge(&desc->tx_q);
+	return 0;
+}
+
+static int btqcomipc_init(struct qcom_btss *desc)
+{
+	struct device *dev = desc->dev;
+	int ret;
+
+	init_waitqueue_head(&desc->wait_q);
+	spin_lock_init(&desc->lock);
+	skb_queue_head_init(&desc->tx_q);
+
+	desc->wq = create_singlethread_workqueue("btss_wq");
+	if (!desc->wq) {
+		dev_err(dev, "Failed to initialize workqueue\n");
+		return -EAGAIN;
+	}
+
+	INIT_WORK(&desc->work, btss_worker);
+
+	ret = devm_request_threaded_irq(dev, desc->irq, NULL, btss_irq_handler,
+					IRQF_TRIGGER_RISING | IRQF_ONESHOT,
+					"btss_irq", desc);
+
+	if (ret)
+		dev_err(dev, "error registering irq[%d] ret = %d\n",
+			desc->irq, ret);
+
+	return ret;
+}
+
+static void btqcomipc_deinit(struct qcom_btss *desc)
+{
+	disable_irq(desc->irq);
+	if (desc->wq != NULL) {
+		flush_workqueue(desc->wq);
+		skb_queue_purge(&desc->tx_q);
+		destroy_workqueue(desc->wq);
+		desc->wq = NULL;
+	}
+}
+
+static int btqcomipc_alloc_memory_region(struct qcom_btss *desc)
+{
+	struct device *dev = desc->dev;
+	struct resource res;
+	int ret;
+
+	ret = of_reserved_mem_region_to_resource(dev->of_node, 0, &res);
+	if (ret) {
+		dev_err(dev, "unable to acquire memory-region resource\n");
+		return ret;
+	}
+
+	desc->mem_phys = res.start;
+	desc->mem_reloc = res.start;
+	desc->mem_size = resource_size(&res);
+	desc->mem_region = devm_ioremap(dev, desc->mem_phys, desc->mem_size);
+	if (!desc->mem_region) {
+		dev_err(dev, "unable to map memory region: %pR\n", &res);
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
+static int btqcomipc_probe(struct platform_device *pdev)
+{
+	struct reset_control *btss_reset;
+	struct device *dev = &pdev->dev;
+	struct qcom_btss *desc;
+	struct hci_dev *hdev;
+	unsigned int args[2];
+	struct clk *lpo_clk;
+	int ret;
+
+	desc = devm_kzalloc(dev, sizeof(*desc), GFP_KERNEL);
+	if (!desc)
+		return -ENOMEM;
+
+	desc->dev = dev;
+
+	ret = of_property_read_string(dev->of_node, "firmware-name",
+				      &desc->firmware);
+	if (ret < 0)
+		return ret;
+
+	ret = btqcomipc_alloc_memory_region(desc);
+	if (ret)
+		return ret;
+
+	desc->regmap = syscon_regmap_lookup_by_phandle_args(dev->of_node,
+							    "qcom,ipc",
+							    2, args);
+	if (IS_ERR(desc->regmap))
+		return PTR_ERR(desc->regmap);
+
+	desc->offset = args[0];
+	desc->bit = args[1];
+
+	lpo_clk = devm_clk_get_enabled(dev, "lpo");
+	if (IS_ERR(lpo_clk))
+		return dev_err_probe(dev, PTR_ERR(lpo_clk),
+				     "Failed to get lpo clock\n");
+
+	btss_reset = devm_reset_control_get_exclusive_deasserted(dev, NULL);
+	if (IS_ERR_OR_NULL(btss_reset))
+		return dev_err_probe(dev, PTR_ERR(btss_reset),
+				     "unable to deassert reset\n");
+
+	desc->irq = platform_get_irq(pdev, 0);
+	if (desc->irq < 0)
+		return dev_err_probe(dev, desc->irq, "Failed to acquire IRQ\n");
+
+	ret = btqcomipc_init(desc);
+	if (ret)
+		return dev_err_probe(dev, ret, "Failed to initialize\n");
+
+	hdev = hci_alloc_dev();
+	if (!hdev) {
+		btqcomipc_deinit(desc);
+		return -ENOMEM;
+	}
+
+	hci_set_drvdata(hdev, desc);
+	desc->hdev = hdev;
+	SET_HCIDEV_DEV(hdev, &pdev->dev);
+	hdev->bus = HCI_IPC;
+
+	hdev->open = btqcomipc_open;
+	hdev->close = btqcomipc_close;
+	hdev->setup = btqcomipc_setup;
+	hdev->send = btqcomipc_send;
+	hdev->flush = btqcomipc_flush;
+	hdev->set_bdaddr = qca_set_bdaddr;
+
+	ret = hci_register_dev(hdev);
+	if (ret < 0) {
+		btqcomipc_deinit(desc);
+		hci_free_dev(hdev);
+		return dev_err_probe(dev, -EBUSY, "Failed to register hdev\n");
+	}
+
+	platform_set_drvdata(pdev, desc);
+
+	return 0;
+}
+
+static void btqcomipc_remove(struct platform_device *pdev)
+{
+	struct qcom_btss *desc = platform_get_drvdata(pdev);
+
+	if (!desc)
+		return;
+
+	btqcomipc_deinit(desc);
+
+	if (desc->hdev) {
+		hci_unregister_dev(desc->hdev);
+		hci_free_dev(desc->hdev);
+	}
+}
+
+static const struct of_device_id btqcomipc_of_match[] = {
+	{ .compatible = "qcom,ipq5018-bt" },
+	{ /* sentinel */},
+};
+MODULE_DEVICE_TABLE(of, btqcomipc_of_match);
+
+static struct platform_driver btqcomipc_driver = {
+	.probe = btqcomipc_probe,
+	.remove = btqcomipc_remove,
+	.driver = {
+		.name = "btqcomipc",
+		.of_match_table = btqcomipc_of_match,
+	},
+};
+
+module_platform_driver(btqcomipc_driver);
+
+MODULE_DESCRIPTION("Qualcomm Bluetooth IPC Driver");
+MODULE_LICENSE("GPL");

-- 
2.53.0

Re: [PATCH v2 4/6] Bluetooth: Introduce Qualcomm IPQ5018 IPC based HCI driver

[Konrad Dybcio]

On 6/29/26 3:01 PM, George Moussalem via B4 Relay wrote:
> From: George Moussalem <george.moussalem@outlook.com>
> 
> Add support for the Bluetooth controller found in the IPQ5018 SoC.
> This driver implements firmware loading and the transport layer between
> the HCI core and the Bluetooth controller.
> 
> The firmware is loaded by the host into the dedicated reserved memory
> carveout and authenticated by TrustZone. A Secure Channel Manager (SCM)
> call safely brings the peripheral core out of reset.
> 
> A shared memory ring buffer topology handles runtime data frame
> transport between the host APSS and the controller.
> 
> An outgoing APCS IPC bit and an incoming GIC interrupt handle host/guest
> signaling.
> 
> Signed-off-by: George Moussalem <george.moussalem@outlook.com>
> ---

[...]

> +#include <linux/bits.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/elf.h>
> +#include <linux/firmware.h>
> +#include <linux/firmware/qcom/qcom_scm.h>
> +#include <linux/init.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/kernel.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_irq.h>
> +#include <linux/of_reserved_mem.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/reset.h>
> +#include <linux/skbuff.h>
> +#include <linux/slab.h>
> +#include <linux/soc/qcom/mdt_loader.h>
> +#include <linux/types.h>
> +#include <linux/workqueue.h>

I don't know for sure, but the amount of the includes suggests some may
be unnecessary

[...]

> +static void btqcomipc_update_stats(struct hci_dev *hdev, struct sk_buff *skb);

I don't think the forward-declaration is necessary


> +static struct ring_buffer_info *btss_get_tx_rbuf(struct qcom_btss *desc,
> +						 bool *is_sbuf_full)
> +{
> +	u8 idx;
> +	struct ring_buffer_info *rinfo;
> +
> +	for (rinfo = &(desc->tx_ctxt->sring_buf_info);	rinfo != NULL;
> +		rinfo = (struct ring_buffer_info *)(uintptr_t)(rinfo->next)) {
> +		idx = (rinfo->widx + 1) % (desc->tx_ctxt->smsg_buf_cnt);

That's one complex for-loop! Maybe move the assignments into the loop body

[...]

> +	/* Account for HCI packet type as it's not included in the skb payload */
> +	len = (skb) ? skb->len + 1 : 0;

Unnecessary parentheses, also in some other places

> +	memset(&aux_ptr, 0, sizeof(struct ipc_aux_ptr));

You can do aux_ptr = { } at declaration

Konrad

[PATCH v2 5/6] arm64: dts: qcom: ipq5018: add nodes required for Bluetooth support

[George Moussalem via B4 Relay]

From: George Moussalem <george.moussalem@outlook.com>

Add nodes for the reserved memory carveout and Bluetooth.

Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
 arch/arm64/boot/dts/qcom/ipq5018.dtsi | 25 ++++++++++++++++++++++++-
 1 file changed, 24 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
index 6f8004a22a1f..65a47ba7d3a3 100644
--- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
+++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
@@ -17,6 +17,23 @@ / {
 	#address-cells = <2>;
 	#size-cells = <2>;
 
+	bluetooth: bluetooth {
+		compatible = "qcom,ipq5018-bt";
+
+		firmware-name = "qca/bt_fw_patch.mbn";
+
+		clocks = <&gcc GCC_BTSS_LPO_CLK>;
+		clock-names = "lpo";
+		resets = <&gcc GCC_BTSS_BCR>;
+
+		qcom,ipc = <&apcs_glb 8 23>;
+		interrupts = <GIC_SPI 162 IRQ_TYPE_EDGE_RISING>;
+
+		memory-region = <&btss_region>;
+
+		status = "disabled";
+	};
+
 	clocks {
 		gephy_rx_clk: gephy-rx-clk {
 			compatible = "fixed-clock";
@@ -136,6 +153,11 @@ reserved-memory {
 		#size-cells = <2>;
 		ranges;
 
+		btss_region: bluetooth@7000000 {
+			reg = <0x0 0x07000000 0x0 0x58000>;
+			no-map;
+		};
+
 		bootloader@4a800000 {
 			reg = <0x0 0x4a800000 0x0 0x200000>;
 			no-map;
@@ -647,7 +669,8 @@ watchdog: watchdog@b017000 {
 
 		apcs_glb: mailbox@b111000 {
 			compatible = "qcom,ipq5018-apcs-apps-global",
-				     "qcom,ipq6018-apcs-apps-global";
+				     "qcom,ipq6018-apcs-apps-global",
+				     "syscon";
 			reg = <0x0b111000 0x1000>;
 			#clock-cells = <1>;
 			clocks = <&a53pll>, <&xo_board_clk>, <&gcc GPLL0>;

-- 
2.53.0

Re: [PATCH v2 5/6] arm64: dts: qcom: ipq5018: add nodes required for Bluetooth support

[Konrad Dybcio]

On 6/29/26 3:01 PM, George Moussalem via B4 Relay wrote:
> From: George Moussalem <george.moussalem@outlook.com>
> 
> Add nodes for the reserved memory carveout and Bluetooth.
> 
> Signed-off-by: George Moussalem <george.moussalem@outlook.com>
> ---
>  arch/arm64/boot/dts/qcom/ipq5018.dtsi | 25 ++++++++++++++++++++++++-
>  1 file changed, 24 insertions(+), 1 deletion(-)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> index 6f8004a22a1f..65a47ba7d3a3 100644
> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
> @@ -17,6 +17,23 @@ / {
>  	#address-cells = <2>;
>  	#size-cells = <2>;
>  
> +	bluetooth: bluetooth {
> +		compatible = "qcom,ipq5018-bt";
> +
> +		firmware-name = "qca/bt_fw_patch.mbn";

Is this fw vendor-signed?

Konrad

Re: [PATCH v2 5/6] arm64: dts: qcom: ipq5018: add nodes required for Bluetooth support

[George Moussalem]

On 6/30/26 15:40, Konrad Dybcio wrote:
> On 6/29/26 3:01 PM, George Moussalem via B4 Relay wrote:
>> From: George Moussalem <george.moussalem@outlook.com>
>>
>> Add nodes for the reserved memory carveout and Bluetooth.
>>
>> Signed-off-by: George Moussalem <george.moussalem@outlook.com>
>> ---
>>  arch/arm64/boot/dts/qcom/ipq5018.dtsi | 25 ++++++++++++++++++++++++-
>>  1 file changed, 24 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
>> index 6f8004a22a1f..65a47ba7d3a3 100644
>> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
>> @@ -17,6 +17,23 @@ / {
>>  	#address-cells = <2>;
>>  	#size-cells = <2>;
>>  
>> +	bluetooth: bluetooth {
>> +		compatible = "qcom,ipq5018-bt";
>> +
>> +		firmware-name = "qca/bt_fw_patch.mbn";
> 
> Is this fw vendor-signed?

I've just analyzed the mbn file (and the mdt + b0x files): it only
contains hashes for the mdt and b02 segments, no signature/certs at all.
I've used your pil squasher to create the mbn file. Here are the FW files:
https://github.com/georgemoussalem/openwrt/tree/ipq50xx-bluetooth/package/firmware/qca-bt-firmware/files

Perhaps you can double check?

> 
> Konrad

Best regards,
George

Re: [PATCH v2 5/6] arm64: dts: qcom: ipq5018: add nodes required for Bluetooth support

[Konrad Dybcio]

On 6/30/26 2:09 PM, George Moussalem wrote:
> On 6/30/26 15:40, Konrad Dybcio wrote:
>> On 6/29/26 3:01 PM, George Moussalem via B4 Relay wrote:
>>> From: George Moussalem <george.moussalem@outlook.com>
>>>
>>> Add nodes for the reserved memory carveout and Bluetooth.
>>>
>>> Signed-off-by: George Moussalem <george.moussalem@outlook.com>
>>> ---
>>>  arch/arm64/boot/dts/qcom/ipq5018.dtsi | 25 ++++++++++++++++++++++++-
>>>  1 file changed, 24 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/arch/arm64/boot/dts/qcom/ipq5018.dtsi b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
>>> index 6f8004a22a1f..65a47ba7d3a3 100644
>>> --- a/arch/arm64/boot/dts/qcom/ipq5018.dtsi
>>> +++ b/arch/arm64/boot/dts/qcom/ipq5018.dtsi
>>> @@ -17,6 +17,23 @@ / {
>>>  	#address-cells = <2>;
>>>  	#size-cells = <2>;
>>>  
>>> +	bluetooth: bluetooth {
>>> +		compatible = "qcom,ipq5018-bt";
>>> +
>>> +		firmware-name = "qca/bt_fw_patch.mbn";
>>
>> Is this fw vendor-signed?
> 
> I've just analyzed the mbn file (and the mdt + b0x files): it only
> contains hashes for the mdt and b02 segments, no signature/certs at all.
> I've used your pil squasher to create the mbn file. Here are the FW files:
> https://github.com/georgemoussalem/openwrt/tree/ipq50xx-bluetooth/package/firmware/qca-bt-firmware/files
> 
> Perhaps you can double check?

Using the not very sophisticated but very quick method of running
strings on it, there's no certificate identifiers indeed

Konrad

[PATCH v2 6/6] MAINTAINERS: Add entry for Qualcomm IPQ5018 Bluetooth driver

[George Moussalem via B4 Relay]

From: George Moussalem <george.moussalem@outlook.com>

Add maintainers entry for Qualcomm IPQ5018 Bluetooth driver.

Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
 MAINTAINERS | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 0b9d7c8276ac..60f7251d1a16 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -22289,6 +22289,13 @@ S:	Maintained
 F:	Documentation/devicetree/bindings/regulator/vqmmc-ipq4019-regulator.yaml
 F:	drivers/regulator/vqmmc-ipq4019-regulator.c
 
+QUALCOMM IPQ5018 BLUETOOTH DRIVER
+M:	George Moussalem <george.moussalem@outlook.com>
+L:	linux-bluetooth@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/net/bluetooth/qcom,ipq5018-bt.yaml
+F:	drivers/bluetooth/btqcomipc.c
+
 QUALCOMM IRIS VIDEO ACCELERATOR DRIVER
 M:	Vikash Garodia <vikash.garodia@oss.qualcomm.com>
 M:	Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>

-- 
2.53.0

[PATCH v3 1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

[George Moussalem via B4 Relay]

From: George Moussalem <george.moussalem@outlook.com>

Document the Qualcomm IPQ5018 Bluetooth controller.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
 .../bindings/net/bluetooth/qcom,ipq5018-bt.yaml    | 86 ++++++++++++++++++++++
 1 file changed, 86 insertions(+)

diff --git a/Documentation/devicetree/bindings/net/bluetooth/qcom,ipq5018-bt.yaml b/Documentation/devicetree/bindings/net/bluetooth/qcom,ipq5018-bt.yaml
new file mode 100644
index 000000000000..2119162994e0
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/bluetooth/qcom,ipq5018-bt.yaml
@@ -0,0 +1,86 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/bluetooth/qcom,ipq5018-bt.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm IPQ5018 Bluetooth
+
+maintainers:
+  - George Moussalem <george.moussalem@outlook.com>
+
+properties:
+  compatible:
+    enum:
+      - qcom,ipq5018-bt
+
+  clocks:
+    items:
+      - description: Bluetooth Subsystem low power oscillator clock
+
+  clock-names:
+    items:
+      - const: lpo
+
+  firmware-name:
+    maxItems: 1
+
+  memory-region:
+    items:
+      - description: |
+          Reserved memory carveout for firmware loading and runtime data
+          transport between the host and the Bluetooth controller.
+
+  interrupts:
+    maxItems: 1
+
+  qcom,ipc:
+    $ref: /schemas/types.yaml#/definitions/phandle-array
+    items:
+      - items:
+          - description: syscon node representing the APCS registers
+          - description: offset to the register within the syscon
+          - description: IPC bit within the register
+    description: |
+      The outgoing IPC bit used for signaling the Bluetooth controller of a host
+      event or for sending an ACK if the remote processor expects it.
+
+  resets:
+    items:
+      - description: Bluetooth Subsystem reset
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - firmware-name
+  - interrupts
+  - qcom,ipc
+  - resets
+
+allOf:
+  - $ref: bluetooth-controller.yaml#
+  - $ref: qcom,bluetooth-common.yaml
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
+
+    bluetooth {
+      compatible = "qcom,ipq5018-bt";
+
+      firmware-name = "qca/bt_fw_patch.mbn";
+
+      clocks = <&gcc GCC_BTSS_LPO_CLK>;
+      clock-names = "lpo";
+      resets = <&gcc GCC_BTSS_BCR>;
+
+      qcom,ipc = <&apcs_glb 8 23>;
+      interrupts = <GIC_SPI 162 IRQ_TYPE_EDGE_RISING>;
+
+      memory-region = <&btss_region>;
+    };

-- 
2.53.0

RE: Add support for IPQ5018 Bluetooth

[bluez.test.bot]

[-- Attachment #1: Type: text/plain, Size: 4428 bytes --]

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=1120861

---Test result---

Test Summary:
CheckPatch                    FAIL      5.23 seconds
VerifyFixes                   PASS      0.10 seconds
VerifySignedoff               PASS      0.10 seconds
GitLint                       FAIL      1.59 seconds
SubjectPrefix                 FAIL      0.57 seconds
BuildKernel                   PASS      25.18 seconds
CheckAllWarning               PASS      27.27 seconds
CheckSparse                   PASS      26.30 seconds
BuildKernel32                 PASS      24.29 seconds
CheckKernelLLVM               SKIP      0.00 seconds
TestRunnerSetup               PASS      456.45 seconds
TestRunner_l2cap-tester       PASS      58.83 seconds
TestRunner_iso-tester         PASS      82.41 seconds
TestRunner_bnep-tester        PASS      18.53 seconds
TestRunner_mgmt-tester        FAIL      216.33 seconds
TestRunner_rfcomm-tester      PASS      29.68 seconds
TestRunner_sco-tester         PASS      32.57 seconds
TestRunner_ioctl-tester       PASS      26.21 seconds
TestRunner_mesh-tester        FAIL      30.98 seconds
TestRunner_smp-tester         PASS      22.90 seconds
TestRunner_userchan-tester    PASS      19.78 seconds
TestRunner_6lowpan-tester     PASS      22.34 seconds
IncrementalBuild              PASS      30.46 seconds

Details
##############################
Test: CheckPatch - FAIL
Desc: Run checkpatch.pl script
Output:
[v3,1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#94: 
new file mode 100644

total: 0 errors, 1 warnings, 86 lines checked

NOTE: For some of the reported defects, checkpatch may be able to
      mechanically convert to the typical style using --fix or --fix-inplace.

/github/workspace/src/patch/14660835.patch has style problems, please review.

NOTE: Ignored message types: UNKNOWN_COMMIT_ID

NOTE: If any of the errors are false positives, please report
      them to the maintainer, see CHECKPATCH in MAINTAINERS.


[v3,4/6] Bluetooth: Introduce Qualcomm IPQ5018 IPC based HCI driver
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#140: 
new file mode 100644

total: 0 errors, 1 warnings, 1065 lines checked

NOTE: For some of the reported defects, checkpatch may be able to
      mechanically convert to the typical style using --fix or --fix-inplace.

/github/workspace/src/patch/14660839.patch has style problems, please review.

NOTE: Ignored message types: UNKNOWN_COMMIT_ID

NOTE: If any of the errors are false positives, please report
      them to the maintainer, see CHECKPATCH in MAINTAINERS.


##############################
Test: GitLint - FAIL
Desc: Run gitlint
Output:
[v3,1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

1: T1 Title exceeds max length (84>80): "[v3,1/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller"
##############################
Test: SubjectPrefix - FAIL
Desc: Check subject contains "Bluetooth" prefix
Output:
"Bluetooth: " prefix is not specified in the subject
"Bluetooth: " prefix is not specified in the subject
"Bluetooth: " prefix is not specified in the subject
"Bluetooth: " prefix is not specified in the subject
##############################
Test: CheckKernelLLVM - SKIP
Desc: Build kernel with LLVM + context analysis
Output:
Clang not found
##############################
Test: TestRunner_mgmt-tester - FAIL
Desc: Run mgmt-tester with test-runner
Output:
Total: 494, Passed: 488 (98.8%), Failed: 2, Not Run: 4

Failed Test Cases
Read Exp Feature - Success                           Failed       0.251 seconds
LL Privacy - Unpair 1                                Timed out    1.899 seconds
##############################
Test: TestRunner_mesh-tester - FAIL
Desc: Run mesh-tester with test-runner
Output:
Total: 10, Passed: 8 (80.0%), Failed: 2, Not Run: 0

Failed Test Cases
Mesh - Send cancel - 1                               Timed out    2.512 seconds
Mesh - Send cancel - 2                               Timed out    1.992 seconds


https://github.com/bluez/bluetooth-next/pull/387

---
Regards,
Linux Bluetooth

[PATCH 1/6] dt-bindings: remoteproc: document M0 Bluetooth Subsystem secure PIL

[George Moussalem via B4 Relay]

From: George Moussalem <george.moussalem@outlook.com>

Document the M0 Bluetooth Subsystem remote processor core found in the
Qualcomm IPQ5018 SoC. Firmware loaded is authenticated via TrustZone.
The firmware running on the M0 core provides bluetooth functionality.

Signed-off-by: George Moussalem <george.moussalem@outlook.com>
---
 .../bindings/remoteproc/qcom,m0-btss-pil.yaml      | 72 ++++++++++++++++++++++
 1 file changed, 72 insertions(+)

diff --git a/Documentation/devicetree/bindings/remoteproc/qcom,m0-btss-pil.yaml b/Documentation/devicetree/bindings/remoteproc/qcom,m0-btss-pil.yaml
new file mode 100644
index 000000000000..397bb6815d71
--- /dev/null
+++ b/Documentation/devicetree/bindings/remoteproc/qcom,m0-btss-pil.yaml
@@ -0,0 +1,72 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/remoteproc/qcom,m0-btss-pil.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm M0 BTSS Peripheral Image Loader
+
+maintainers:
+  - George Moussalem <george.moussalem@outlook.com>
+
+description:
+  Qualcomm M0 BTSS Peripheral Secure Image Loader loads firmware and powers up
+  the M0 BTSS remote processor core on the Qualcomm IPQ5018 SoC.
+
+properties:
+  compatible:
+    enum:
+      - qcom,ipq5018-btss-pil
+
+  firmware-name:
+    maxItems: 1
+    description: Firmware name for the M0 Bluetooth Subsystem core
+
+  clocks:
+    items:
+      - description: M0 BTSS low power oscillator clock
+
+  clock-names:
+    items:
+      - const: btss_lpo_clk
+
+  memory-region:
+    items:
+      - description: M0 BTSS reserved memory carveout
+
+  resets:
+    items:
+      - description: M0 BTSS reset
+
+  reset-names:
+    items:
+      - const: btss_reset
+
+required:
+  - compatible
+  - firmware-name
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+  - memory-region
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/qcom,gcc-ipq5018.h>
+    #include <dt-bindings/reset/qcom,gcc-ipq5018.h>
+
+    remoteproc {
+      compatible = "qcom,ipq5018-btss-pil";
+
+      firmware-name = "qca/bt_fw_patch.mbn";
+
+      clocks = <&gcc GCC_BTSS_LPO_CLK>;
+      clock-names = "btss_lpo_clk";
+      resets = <&gcc GCC_BTSS_BCR>;
+      reset-names = "btss_reset";
+
+      memory-region = <&btss_region>;
+    };

-- 
2.53.0

RE: Add support for IPQ5018 Bluetooth

[bluez.test.bot]

[-- Attachment #1: Type: text/plain, Size: 5640 bytes --]

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=1116589

---Test result---

Test Summary:
CheckPatch                    FAIL      10.08 seconds
VerifyFixes                   PASS      0.27 seconds
VerifySignedoff               PASS      0.31 seconds
GitLint                       FAIL      3.87 seconds
SubjectPrefix                 FAIL      1.71 seconds
BuildKernel                   PASS      25.31 seconds
CheckAllWarning               PASS      27.86 seconds
CheckSparse                   PASS      28.46 seconds
BuildKernel32                 PASS      24.83 seconds
CheckKernelLLVM               SKIP      0.00 seconds
TestRunnerSetup               PASS      459.56 seconds
TestRunner_l2cap-tester       PASS      58.15 seconds
TestRunner_iso-tester         PASS      74.50 seconds
TestRunner_bnep-tester        PASS      19.39 seconds
TestRunner_mgmt-tester        FAIL      211.62 seconds
TestRunner_rfcomm-tester      PASS      25.51 seconds
TestRunner_sco-tester         PASS      32.73 seconds
TestRunner_ioctl-tester       PASS      25.67 seconds
TestRunner_mesh-tester        FAIL      26.17 seconds
TestRunner_smp-tester         PASS      23.93 seconds
TestRunner_userchan-tester    PASS      19.86 seconds
TestRunner_6lowpan-tester     PASS      22.74 seconds
IncrementalBuild              PASS      37.70 seconds

Details
##############################
Test: CheckPatch - FAIL
Desc: Run checkpatch.pl script
Output:
[1/6] dt-bindings: remoteproc: document M0 Bluetooth Subsystem secure PIL
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#108: 
new file mode 100644

total: 0 errors, 1 warnings, 72 lines checked

NOTE: For some of the reported defects, checkpatch may be able to
      mechanically convert to the typical style using --fix or --fix-inplace.

/github/workspace/src/patch/14645041.patch has style problems, please review.

NOTE: Ignored message types: UNKNOWN_COMMIT_ID

NOTE: If any of the errors are false positives, please report
      them to the maintainer, see CHECKPATCH in MAINTAINERS.


[2/6] remoteproc: qcom: Add M0 BTSS secure PIL driver
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#147: 
new file mode 100644

total: 0 errors, 1 warnings, 286 lines checked

NOTE: For some of the reported defects, checkpatch may be able to
      mechanically convert to the typical style using --fix or --fix-inplace.

/github/workspace/src/patch/14645042.patch has style problems, please review.

NOTE: Ignored message types: UNKNOWN_COMMIT_ID

NOTE: If any of the errors are false positives, please report
      them to the maintainer, see CHECKPATCH in MAINTAINERS.


[4/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#106: 
new file mode 100644

total: 0 errors, 1 warnings, 63 lines checked

NOTE: For some of the reported defects, checkpatch may be able to
      mechanically convert to the typical style using --fix or --fix-inplace.

/github/workspace/src/patch/14645044.patch has style problems, please review.

NOTE: Ignored message types: UNKNOWN_COMMIT_ID

NOTE: If any of the errors are false positives, please report
      them to the maintainer, see CHECKPATCH in MAINTAINERS.


[5/6] Bluetooth: Introduce Qualcomm IPQ5018 IPC based HCI driver
WARNING: added, moved or deleted file(s), does MAINTAINERS need updating?
#150: 
new file mode 100644

total: 0 errors, 1 warnings, 963 lines checked

NOTE: For some of the reported defects, checkpatch may be able to
      mechanically convert to the typical style using --fix or --fix-inplace.

/github/workspace/src/patch/14645046.patch has style problems, please review.

NOTE: Ignored message types: UNKNOWN_COMMIT_ID

NOTE: If any of the errors are false positives, please report
      them to the maintainer, see CHECKPATCH in MAINTAINERS.


##############################
Test: GitLint - FAIL
Desc: Run gitlint
Output:
[4/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller

1: T1 Title exceeds max length (81>80): "[4/6] dt-bindings: net: bluetooth: Document Qualcomm IPQ5018 Bluetooth controller"
##############################
Test: SubjectPrefix - FAIL
Desc: Check subject contains "Bluetooth" prefix
Output:
"Bluetooth: " prefix is not specified in the subject
"Bluetooth: " prefix is not specified in the subject
"Bluetooth: " prefix is not specified in the subject
"Bluetooth: " prefix is not specified in the subject
##############################
Test: CheckKernelLLVM - SKIP
Desc: Build kernel with LLVM + context analysis
Output:
Clang not found
##############################
Test: TestRunner_mgmt-tester - FAIL
Desc: Run mgmt-tester with test-runner
Output:
Total: 494, Passed: 488 (98.8%), Failed: 2, Not Run: 4

Failed Test Cases
Read Exp Feature - Success                           Failed       0.245 seconds
LL Privacy - Unpair 1                                Timed out    1.861 seconds
##############################
Test: TestRunner_mesh-tester - FAIL
Desc: Run mesh-tester with test-runner
Output:
Total: 10, Passed: 8 (80.0%), Failed: 2, Not Run: 0

Failed Test Cases
Mesh - Send cancel - 1                               Timed out    2.742 seconds
Mesh - Send cancel - 2                               Timed out    1.989 seconds


https://github.com/bluez/bluetooth-next/pull/352

---
Regards,
Linux Bluetooth