[PATCH V2 0/8] Add PCIe M.2 Key E connector support for NXP i.MX boards

[PATCH V2 0/8] Add PCIe M.2 Key E connector support for NXP i.MX boards

[Sherry Sun (OSS)]

From: Sherry Sun <sherry.sun@nxp.com>

This series adds support for NXP Wi-Fi/BT combo chips (88W9098, AW693)
inserted into PCIe M.2 Key E connectors on several i.MX EVK/MEK boards.

For M.2 cards that rely on PCIe L2 link state and wake-up mechanisms, the
card must remain powered during suspend. Patch #1 uses the existing
dw_pcie_rp::skip_pwrctrl_off flag to skip power-off during suspend and skip
power-on during the init path.

Also the btnxpuart driver is extended to obtain a pwrseq descriptor via the
OF graph on the UART controller device in patch #3.

Note: Patch #4-8 in this patch set depends on the following [1] and [2]
DTS patches.
[1] https://lore.kernel.org/all/20260616105201.3214395-1-sherry.sun@oss.nxp.com/
[2] https://lore.kernel.org/all/20260520084904.2424253-1-sherry.sun@oss.nxp.com/

---
Changes in V2:
1. Rebased on top of 7.1.0.
2. Removed the power_off error handling in patch #3 because pwrseq_put()
   would call pwrseq_power_off() to automatically clean.
3. Collected the tags.
---

Sherry Sun (8):
  PCI: imx6: Add skip_pwrctrl_off flag support
  power: sequencing: pcie-m2: Add PCI ID for NXP 88W9098 and AW693
    Bluetooth
  Bluetooth: btnxpuart: Add M.2 Bluetooth device support using pwrseq
  arm64: dts: imx8mq-evk: Describe the PCIe M.2 Key E connector
  arm64: dts: imx95-19x19-evk: Describe the PCIe M.2 Key E connector
  arm64: dts: imx8dxl-evk: Describe the PCIe M.2 Key E connector
  arm64: dts: imx8qm-mek: Describe the PCIe M.2 Key E connector
  arm64: dts: imx8qxp-mek: Describe the PCIe M.2 Key E connector

 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 56 +++++++++++++-----
 arch/arm64/boot/dts/freescale/imx8mq-evk.dts  | 44 ++++++++++++--
 arch/arm64/boot/dts/freescale/imx8qm-mek.dts  | 58 ++++++++++++++-----
 arch/arm64/boot/dts/freescale/imx8qxp-mek.dts | 54 ++++++++++++-----
 .../boot/dts/freescale/imx95-19x19-evk.dts    | 55 +++++++++++++-----
 drivers/bluetooth/btnxpuart.c                 | 14 +++++
 drivers/pci/controller/dwc/pci-imx6.c         | 36 +++++++-----
 drivers/power/sequencing/pwrseq-pcie-m2.c     |  4 ++
 8 files changed, 248 insertions(+), 73 deletions(-)

-- 
2.50.1

[PATCH V2 1/8] PCI: imx6: Add skip_pwrctrl_off flag support

[Sherry Sun (OSS)]

From: Sherry Sun <sherry.sun@nxp.com>

Use dw_pcie_rp::skip_pwrctrl_off to avoid powering off devices during
suspend to preserve wakeup capability of the devices and also not to power
on the devices in the init path.
This allows controller power-off to be skipped when some devices(e.g. M.2
cards key E without auxiliary power) required to support PCIe L2 link state
and wake-up mechanisms.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 drivers/pci/controller/dwc/pci-imx6.c | 36 +++++++++++++++++----------
 1 file changed, 23 insertions(+), 13 deletions(-)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 0fa716d1ed75..ff5a9565dbbf 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -1382,16 +1382,20 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
 		}
 	}
 
-	ret = pci_pwrctrl_create_devices(dev);
-	if (ret) {
-		dev_err(dev, "failed to create pwrctrl devices\n");
-		goto err_reg_disable;
+	if (!pci->suspended) {
+		ret = pci_pwrctrl_create_devices(dev);
+		if (ret) {
+			dev_err(dev, "failed to create pwrctrl devices\n");
+			goto err_reg_disable;
+		}
 	}
 
-	ret = pci_pwrctrl_power_on_devices(dev);
-	if (ret) {
-		dev_err(dev, "failed to power on pwrctrl devices\n");
-		goto err_pwrctrl_destroy;
+	if (!pp->skip_pwrctrl_off) {
+		ret = pci_pwrctrl_power_on_devices(dev);
+		if (ret) {
+			dev_err(dev, "failed to power on pwrctrl devices\n");
+			goto err_pwrctrl_destroy;
+		}
 	}
 
 	ret = imx_pcie_clk_enable(imx_pcie);
@@ -1460,9 +1464,10 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
 err_clk_disable:
 	imx_pcie_clk_disable(imx_pcie);
 err_pwrctrl_power_off:
-	pci_pwrctrl_power_off_devices(dev);
+	if (!pp->skip_pwrctrl_off)
+		pci_pwrctrl_power_off_devices(dev);
 err_pwrctrl_destroy:
-	if (ret != -EPROBE_DEFER)
+	if (ret != -EPROBE_DEFER && !pci->suspended)
 		pci_pwrctrl_destroy_devices(dev);
 err_reg_disable:
 	if (imx_pcie->vpcie)
@@ -1482,7 +1487,8 @@ static void imx_pcie_host_exit(struct dw_pcie_rp *pp)
 	}
 	imx_pcie_clk_disable(imx_pcie);
 
-	pci_pwrctrl_power_off_devices(pci->dev);
+	if (!pci->pp.skip_pwrctrl_off)
+		pci_pwrctrl_power_off_devices(pci->dev);
 	if (imx_pcie->vpcie)
 		regulator_disable(imx_pcie->vpcie);
 }
@@ -1990,12 +1996,16 @@ static int imx_pcie_probe(struct platform_device *pdev)
 static void imx_pcie_shutdown(struct platform_device *pdev)
 {
 	struct imx_pcie *imx_pcie = platform_get_drvdata(pdev);
+	struct dw_pcie *pci = imx_pcie->pci;
+	struct dw_pcie_rp *pp = &pci->pp;
 
 	/* bring down link, so bootloader gets clean state in case of reboot */
 	imx_pcie_assert_core_reset(imx_pcie);
 	imx_pcie_assert_perst(imx_pcie, true);
-	pci_pwrctrl_power_off_devices(&pdev->dev);
-	pci_pwrctrl_destroy_devices(&pdev->dev);
+	if (!pp->skip_pwrctrl_off)
+		pci_pwrctrl_power_off_devices(&pdev->dev);
+	if (!pci->suspended)
+		pci_pwrctrl_destroy_devices(&pdev->dev);
 }
 
 static const struct imx_pcie_drvdata drvdata[] = {
-- 
2.50.1

RE: Add PCIe M.2 Key E connector support for NXP i.MX boards

[bluez.test.bot]

[-- Attachment #1: Type: text/plain, Size: 577 bytes --]

This is an automated email and please do not reply to this email.

Dear Submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
While preparing the CI tests, the patches you submitted couldn't be applied to the current HEAD of the repository.

----- Output -----

error: patch failed: drivers/pci/controller/dwc/pci-imx6.c:1382
error: drivers/pci/controller/dwc/pci-imx6.c: patch does not apply
hint: Use 'git am --show-current-patch' to see the failed patch

Please resolve the issue and submit the patches again.


---
Regards,
Linux Bluetooth

Re: [PATCH V2 1/8] PCI: imx6: Add skip_pwrctrl_off flag support

[Frank Li]

On Tue, Jun 23, 2026 at 11:07:28AM +0800, Sherry Sun (OSS) wrote:
> From: Sherry Sun <sherry.sun@nxp.com>
>
> Use dw_pcie_rp::skip_pwrctrl_off to avoid powering off devices during
> suspend to preserve wakeup capability of the devices and also not to power
> on the devices in the init path.
> This allows controller power-off to be skipped when some devices(e.g. M.2
> cards key E without auxiliary power) required to support PCIe L2 link state
> and wake-up mechanisms.
>
> Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
> ---
>  drivers/pci/controller/dwc/pci-imx6.c | 36 +++++++++++++++++----------
>  1 file changed, 23 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
> index 0fa716d1ed75..ff5a9565dbbf 100644
> --- a/drivers/pci/controller/dwc/pci-imx6.c
> +++ b/drivers/pci/controller/dwc/pci-imx6.c
> @@ -1382,16 +1382,20 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
>  		}
>  	}
>
> -	ret = pci_pwrctrl_create_devices(dev);
> -	if (ret) {
> -		dev_err(dev, "failed to create pwrctrl devices\n");
> -		goto err_reg_disable;
> +	if (!pci->suspended) {
> +		ret = pci_pwrctrl_create_devices(dev);

Is possible move pci_pwrctrl_create_devices() of pci_pwrctrl_create_devices

and call it direct at probe() function, like other regulator_get function.

Frank

> +		if (ret) {
> +			dev_err(dev, "failed to create pwrctrl devices\n");
> +			goto err_reg_disable;
> +		}
>  	}
>
> -	ret = pci_pwrctrl_power_on_devices(dev);
> -	if (ret) {
> -		dev_err(dev, "failed to power on pwrctrl devices\n");
> -		goto err_pwrctrl_destroy;
> +	if (!pp->skip_pwrctrl_off) {
> +		ret = pci_pwrctrl_power_on_devices(dev);
> +		if (ret) {
> +			dev_err(dev, "failed to power on pwrctrl devices\n");
> +			goto err_pwrctrl_destroy;
> +		}
>  	}
>
>  	ret = imx_pcie_clk_enable(imx_pcie);
> @@ -1460,9 +1464,10 @@ static int imx_pcie_host_init(struct dw_pcie_rp *pp)
>  err_clk_disable:
>  	imx_pcie_clk_disable(imx_pcie);
>  err_pwrctrl_power_off:
> -	pci_pwrctrl_power_off_devices(dev);
> +	if (!pp->skip_pwrctrl_off)
> +		pci_pwrctrl_power_off_devices(dev);
>  err_pwrctrl_destroy:
> -	if (ret != -EPROBE_DEFER)
> +	if (ret != -EPROBE_DEFER && !pci->suspended)
>  		pci_pwrctrl_destroy_devices(dev);
>  err_reg_disable:
>  	if (imx_pcie->vpcie)
> @@ -1482,7 +1487,8 @@ static void imx_pcie_host_exit(struct dw_pcie_rp *pp)
>  	}
>  	imx_pcie_clk_disable(imx_pcie);
>
> -	pci_pwrctrl_power_off_devices(pci->dev);
> +	if (!pci->pp.skip_pwrctrl_off)
> +		pci_pwrctrl_power_off_devices(pci->dev);
>  	if (imx_pcie->vpcie)
>  		regulator_disable(imx_pcie->vpcie);
>  }
> @@ -1990,12 +1996,16 @@ static int imx_pcie_probe(struct platform_device *pdev)
>  static void imx_pcie_shutdown(struct platform_device *pdev)
>  {
>  	struct imx_pcie *imx_pcie = platform_get_drvdata(pdev);
> +	struct dw_pcie *pci = imx_pcie->pci;
> +	struct dw_pcie_rp *pp = &pci->pp;
>
>  	/* bring down link, so bootloader gets clean state in case of reboot */
>  	imx_pcie_assert_core_reset(imx_pcie);
>  	imx_pcie_assert_perst(imx_pcie, true);
> -	pci_pwrctrl_power_off_devices(&pdev->dev);
> -	pci_pwrctrl_destroy_devices(&pdev->dev);
> +	if (!pp->skip_pwrctrl_off)
> +		pci_pwrctrl_power_off_devices(&pdev->dev);
> +	if (!pci->suspended)
> +		pci_pwrctrl_destroy_devices(&pdev->dev);
>  }
>
>  static const struct imx_pcie_drvdata drvdata[] = {
> --
> 2.50.1
>
>

[PATCH V2 2/8] power: sequencing: pcie-m2: Add PCI ID for NXP 88W9098 and AW693 Bluetooth

[Sherry Sun (OSS)]

From: Sherry Sun <sherry.sun@nxp.com>

88W9098 is a NXP Wi-Fi/BT combo chip with PCI device ID 0x2b43 under
Marvell Extended vendor ID. AW693 is a NXP Wi-Fi/BT combo chip with
PCI device ID 0x3003 under NXP/Philips vendor ID.

Add both chips to pwrseq_m2_pci_ids[] so that the pwrseq-pcie-m2 driver
can create the Bluetooth serdev device when these cards are inserted into
a PCIe M.2 Key E connector.

Both chips use "nxp,88w8987-bt" as the serdev compatible string, which
is the entry point for the btnxpuart driver. The driver identifies the
actual chip variant at runtime via chip ID auto-detection and loads the
appropriate firmware accordingly.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
---
 drivers/power/sequencing/pwrseq-pcie-m2.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/power/sequencing/pwrseq-pcie-m2.c b/drivers/power/sequencing/pwrseq-pcie-m2.c
index b5ed80d03953..e3ba9169144d 100644
--- a/drivers/power/sequencing/pwrseq-pcie-m2.c
+++ b/drivers/power/sequencing/pwrseq-pcie-m2.c
@@ -186,6 +186,10 @@ static int pwrseq_pcie_m2_match(struct pwrseq_device *pwrseq,
 }
 
 static const struct pci_device_id pwrseq_m2_pci_ids[] = {
+	{ PCI_DEVICE(PCI_VENDOR_ID_MARVELL_EXT, 0x2b43),
+	  .driver_data = (kernel_ulong_t)"nxp,88w8987-bt" },
+	{ PCI_DEVICE(PCI_VENDOR_ID_PHILIPS, 0x3003),
+	  .driver_data = (kernel_ulong_t)"nxp,88w8987-bt" },
 	{ PCI_DEVICE(PCI_VENDOR_ID_QCOM, 0x1103),
 	  .driver_data = (kernel_ulong_t)"qcom,wcn6855-bt" },
 	{ PCI_DEVICE(PCI_VENDOR_ID_QCOM, 0x1107),
-- 
2.50.1

[PATCH V2 3/8] Bluetooth: btnxpuart: Add M.2 Bluetooth device support using pwrseq

[Sherry Sun (OSS)]

From: Sherry Sun <sherry.sun@nxp.com>

Power supply to the M.2 Bluetooth device attached to the host using M.2
connector is controlled using the 'uart' pwrseq device. So add support for
getting the pwrseq device if the OF graph link is present. Once obtained,
pwrseq_power_on() is called to power up the M.2 Bluetooth card. The power
sequencer descriptor is obtained via devm_pwrseq_get(), so the power-off
and cleanup are handled automatically when the device is unbound.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 drivers/bluetooth/btnxpuart.c | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/drivers/bluetooth/btnxpuart.c b/drivers/bluetooth/btnxpuart.c
index e7036a48ce48..438ccaa2b56d 100644
--- a/drivers/bluetooth/btnxpuart.c
+++ b/drivers/bluetooth/btnxpuart.c
@@ -9,6 +9,8 @@
 
 #include <linux/serdev.h>
 #include <linux/of.h>
+#include <linux/of_graph.h>
+#include <linux/pwrseq/consumer.h>
 #include <linux/skbuff.h>
 #include <linux/unaligned.h>
 #include <linux/firmware.h>
@@ -1866,6 +1868,18 @@ static int nxp_serdev_probe(struct serdev_device *serdev)
 		return err;
 	}
 
+	if (of_graph_is_present(dev_of_node(&serdev->ctrl->dev))) {
+		struct pwrseq_desc *pwrseq;
+
+		pwrseq = devm_pwrseq_get(&serdev->ctrl->dev, "uart");
+		if (IS_ERR(pwrseq))
+			return PTR_ERR(pwrseq);
+
+		err = pwrseq_power_on(pwrseq);
+		if (err)
+			return err;
+	}
+
 	/* Initialize and register HCI device */
 	hdev = hci_alloc_dev();
 	if (!hdev) {
-- 
2.50.1

Re: [PATCH V2 3/8] Bluetooth: btnxpuart: Add M.2 Bluetooth device support using pwrseq

[Bartosz Golaszewski]

On Tue, 23 Jun 2026 05:07:30 +0200, "Sherry Sun (OSS)"
<sherry.sun@oss.nxp.com> said:
> From: Sherry Sun <sherry.sun@nxp.com>
>
> Power supply to the M.2 Bluetooth device attached to the host using M.2
> connector is controlled using the 'uart' pwrseq device. So add support for
> getting the pwrseq device if the OF graph link is present. Once obtained,
> pwrseq_power_on() is called to power up the M.2 Bluetooth card. The power
> sequencer descriptor is obtained via devm_pwrseq_get(), so the power-off
> and cleanup are handled automatically when the device is unbound.
>
> Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
> ---

Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>

Re: [PATCH V2 3/8] Bluetooth: btnxpuart: Add M.2 Bluetooth device support using pwrseq

[Frank Li]

On Tue, Jun 23, 2026 at 11:07:30AM +0800, Sherry Sun (OSS) wrote:
> From: Sherry Sun <sherry.sun@nxp.com>
>
> Power supply to the M.2 Bluetooth device attached to the host using M.2
> connector is controlled using the 'uart' pwrseq device. So add support for
> getting the pwrseq device if the OF graph link is present. Once obtained,
> pwrseq_power_on() is called to power up the M.2 Bluetooth card. The power
> sequencer descriptor is obtained via devm_pwrseq_get(), so the power-off
> and cleanup are handled automatically when the device is unbound.
>
> Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
> ---

Reviewed-by: Frank Li <Frank.Li@nxp.com>

>  drivers/bluetooth/btnxpuart.c | 14 ++++++++++++++
>  1 file changed, 14 insertions(+)
>
> diff --git a/drivers/bluetooth/btnxpuart.c b/drivers/bluetooth/btnxpuart.c
> index e7036a48ce48..438ccaa2b56d 100644
> --- a/drivers/bluetooth/btnxpuart.c
> +++ b/drivers/bluetooth/btnxpuart.c
> @@ -9,6 +9,8 @@
>
>  #include <linux/serdev.h>
>  #include <linux/of.h>
> +#include <linux/of_graph.h>
> +#include <linux/pwrseq/consumer.h>
>  #include <linux/skbuff.h>
>  #include <linux/unaligned.h>
>  #include <linux/firmware.h>
> @@ -1866,6 +1868,18 @@ static int nxp_serdev_probe(struct serdev_device *serdev)
>  		return err;
>  	}
>
> +	if (of_graph_is_present(dev_of_node(&serdev->ctrl->dev))) {
> +		struct pwrseq_desc *pwrseq;
> +
> +		pwrseq = devm_pwrseq_get(&serdev->ctrl->dev, "uart");
> +		if (IS_ERR(pwrseq))
> +			return PTR_ERR(pwrseq);
> +
> +		err = pwrseq_power_on(pwrseq);
> +		if (err)
> +			return err;
> +	}
> +
>  	/* Initialize and register HCI device */
>  	hdev = hci_alloc_dev();
>  	if (!hdev) {
> --
> 2.50.1
>
>

[PATCH V2 4/8] arm64: dts: imx8mq-evk: Describe the PCIe M.2 Key E connector

[Sherry Sun (OSS)]

From: Sherry Sun <sherry.sun@nxp.com>

The i.MX8MQ-EVK has the PCIe M.2 Mechanical Key E connector to connect
wireless connectivity cards over PCIe and UART interfaces. Hence,
describe the connector node and link it with the PCIe 1 Root Port and
UART3 nodes through graph port/endpoint.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8mq-evk.dts | 44 ++++++++++++++++++--
 1 file changed, 40 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
index 71504a0af87f..482e5203e879 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-evk.dts
@@ -21,6 +21,36 @@ memory@40000000 {
 		reg = <0x00000000 0x40000000 0 0xc0000000>;
 	};
 
+	m2-connector {
+		compatible = "pcie-m2-e-connector";
+		vpcie3v3-supply = <&reg_pcie1>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+				m2_e_pcie_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&pcie1_port0_ep>;
+				};
+			};
+
+			port@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+				m2_e_uart_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&uart3_ep>;
+				};
+			};
+		};
+	};
+
 	pcie0_refclk: pcie0-refclk {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -420,8 +450,12 @@ &pcie1_ep {
 
 &pcie1_port0 {
 	reset-gpios = <&gpio5 12 GPIO_ACTIVE_LOW>;
-	vpcie-supply = <&reg_pcie1>;
-	vpcie3v3aux-supply = <&reg_pcie1>;
+
+	port {
+		pcie1_port0_ep: endpoint {
+			remote-endpoint = <&m2_e_pcie_ep>;
+		};
+	};
 };
 
 &pgc_gpu {
@@ -506,8 +540,10 @@ &uart3 { /* BT */
 	uart-has-rtscts;
 	status = "okay";
 
-	bluetooth {
-		compatible = "nxp,88w8987-bt";
+	port {
+		uart3_ep: endpoint {
+			remote-endpoint = <&m2_e_uart_ep>;
+		};
 	};
 };
 
-- 
2.50.1

[PATCH V2 5/8] arm64: dts: imx95-19x19-evk: Describe the PCIe M.2 Key E connector

[Sherry Sun (OSS)]

From: Sherry Sun <sherry.sun@nxp.com>

The i.MX95-19x19-EVK has the PCIe M.2 Mechanical Key E connector to
connect wireless connectivity cards over PCIe and UART interfaces. Hence,
describe the connector node and link it with the PCIe 0 Root Port and
LPUART5 nodes through graph port/endpoint.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 .../boot/dts/freescale/imx95-19x19-evk.dts    | 55 ++++++++++++++-----
 1 file changed, 41 insertions(+), 14 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
index c08731dfb1ee..d2c0345f0d61 100644
--- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
@@ -57,6 +57,37 @@ memory@80000000 {
 		reg = <0x0 0x80000000 0 0x80000000>;
 	};
 
+	m2-connector {
+		compatible = "pcie-m2-e-connector";
+		vpcie3v3-supply = <&reg_m2_pwr>;
+		w-disable1-gpios = <&i2c7_pcal6524 6 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+				m2_e_pcie_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&pcie0_port0_ep>;
+				};
+			};
+
+			port@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+				m2_e_uart_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&lpuart5_ep>;
+				};
+			};
+		};
+	};
+
 	fan0: pwm-fan {
 		compatible = "pwm-fan";
 		#cooling-cells = <2>;
@@ -145,16 +176,6 @@ reg_m2_pwr: regulator-m2-pwr {
 		startup-delay-us = <5000>;
 	};
 
-	reg_pcie0: regulator-pcie {
-		compatible = "regulator-fixed";
-		regulator-name = "PCIE_WLAN_EN";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&reg_m2_pwr>;
-		gpio = <&i2c7_pcal6524 6 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	reg_slot_pwr: regulator-slot-pwr {
 		compatible = "regulator-fixed";
 		regulator-name = "PCIe slot-power";
@@ -477,8 +498,10 @@ &lpuart5 {
 	pinctrl-0 = <&pinctrl_uart5>;
 	status = "okay";
 
-	bluetooth {
-		compatible = "nxp,88w8987-bt";
+	port {
+		lpuart5_ep: endpoint {
+			remote-endpoint = <&m2_e_uart_ep>;
+		};
 	};
 };
 
@@ -555,8 +578,12 @@ &pcie0_ep {
 
 &pcie0_port0 {
 	reset-gpios = <&i2c7_pcal6524 5 GPIO_ACTIVE_LOW>;
-	vpcie-supply = <&reg_pcie0>;
-	vpcie3v3aux-supply = <&reg_pcie0>;
+
+	port {
+		pcie0_port0_ep: endpoint {
+			remote-endpoint = <&m2_e_pcie_ep>;
+		};
+	};
 };
 
 &pcie1 {
-- 
2.50.1

[PATCH V2 6/8] arm64: dts: imx8dxl-evk: Describe the PCIe M.2 Key E connector

[Sherry Sun (OSS)]

From: Sherry Sun <sherry.sun@nxp.com>

The i.MX8DXL-EVK has the PCIe M.2 Mechanical Key E connector to connect
wireless connectivity cards over PCIe and UART interfaces. Hence,
describe the connector node and link it with the PCIe b Root Port and
LPUART1 nodes through graph port/endpoint.

The M.2 Key E connector is powered by a 3.3V fixed regulator
(reg_audio_3v3), add a reg_3v3 label to avoid confusion.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8dxl-evk.dts | 56 ++++++++++++++-----
 1 file changed, 42 insertions(+), 14 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
index 1084164d1381..6afee1f1a9fc 100644
--- a/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8dxl-evk.dts
@@ -42,6 +42,37 @@ memory@80000000 {
 		reg = <0x00000000 0x80000000 0 0x40000000>;
 	};
 
+	m2-connector {
+		compatible = "pcie-m2-e-connector";
+		vpcie3v3-supply = <&reg_3v3>;
+		w-disable1-gpios = <&pca6416_1 13 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+				m2_e_pcie_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&pcieb_port0_ep>;
+				};
+			};
+
+			port@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+				m2_e_uart_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&lpuart1_ep>;
+				};
+			};
+		};
+	};
+
 	reserved-memory {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -182,15 +213,6 @@ mii_select: regulator-4 {
 		regulator-always-on;
 	};
 
-	reg_pcieb: regulator-pcieb {
-		compatible = "regulator-fixed";
-		regulator-max-microvolt = <3300000>;
-		regulator-min-microvolt = <3300000>;
-		regulator-name = "reg_pcieb";
-		gpio = <&pca6416_1 13 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	reg_audio_5v: regulator-audio-pwr {
 		compatible = "regulator-fixed";
 		regulator-name = "audio-5v";
@@ -200,7 +222,7 @@ reg_audio_5v: regulator-audio-pwr {
 		regulator-boot-on;
 	};
 
-	reg_audio_3v3: regulator-audio-3v3 {
+	reg_3v3: reg_audio_3v3: regulator-audio-3v3 {
 		compatible = "regulator-fixed";
 		regulator-name = "audio-3v3";
 		regulator-min-microvolt = <3300000>;
@@ -623,8 +645,10 @@ &lpuart1 {
 	pinctrl-0 = <&pinctrl_lpuart1>;
 	status = "okay";
 
-	bluetooth {
-		compatible = "nxp,88w8987-bt";
+	port {
+		lpuart1_ep: endpoint {
+			remote-endpoint = <&m2_e_uart_ep>;
+		};
 	};
 };
 
@@ -690,8 +714,12 @@ &pcie0_ep {
 
 &pcieb_port0 {
 	reset-gpios = <&lsio_gpio4 0 GPIO_ACTIVE_LOW>;
-	vpcie-supply = <&reg_pcieb>;
-	vpcie3v3aux-supply = <&reg_pcieb>;
+
+	port {
+		pcieb_port0_ep: endpoint {
+			remote-endpoint = <&m2_e_pcie_ep>;
+		};
+	};
 };
 
 &sai0 {
-- 
2.50.1

[PATCH V2 7/8] arm64: dts: imx8qm-mek: Describe the PCIe M.2 Key E connector

[Sherry Sun (OSS)]

From: Sherry Sun <sherry.sun@nxp.com>

The i.MX8QM-MEK has the PCIe M.2 Mechanical Key E connector to connect
wireless connectivity cards over PCIe and UART interfaces. Hence,
describe the connector node and link it with the PCIe a Root Port and
LPUART1 nodes through graph port/endpoint.

The M.2 Key E connector is powered by a 3.3V fixed regulator
(reg_3v3) on board.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8qm-mek.dts | 58 +++++++++++++++-----
 1 file changed, 43 insertions(+), 15 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
index 5e725ad8aef9..4c02592cfe14 100644
--- a/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qm-mek.dts
@@ -32,6 +32,39 @@ memory@80000000 {
 		reg = <0x00000000 0x80000000 0 0x40000000>;
 	};
 
+	m2-connector {
+		compatible = "pcie-m2-e-connector";
+		pinctrl-0 = <&pinctrl_pciea_reg>;
+		pinctrl-names = "default";
+		vpcie3v3-supply = <&reg_3v3>;
+		w-disable1-gpios = <&lsio_gpio1 13 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+				m2_e_pcie_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&pciea_port0_ep>;
+				};
+			};
+
+			port@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+				m2_e_uart_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&lpuart1_ep>;
+				};
+			};
+		};
+	};
+
 	xtal24m: clock-xtal24m {
 		compatible = "fixed-clock";
 		#clock-cells = <0>;
@@ -320,17 +353,6 @@ reg_can2_stby: regulator-can2-stby {
 		vin-supply = <&reg_can2_en>;
 	};
 
-	reg_pciea: regulator-pcie {
-		compatible = "regulator-fixed";
-		pinctrl-0 = <&pinctrl_pciea_reg>;
-		pinctrl-names = "default";
-		regulator-max-microvolt = <3300000>;
-		regulator-min-microvolt = <3300000>;
-		regulator-name = "mpcie_3v3";
-		gpio = <&lsio_gpio1 13 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	reg_usb_otg1_vbus: regulator-usbotg1-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "usb_otg1_vbus";
@@ -718,8 +740,10 @@ &lpuart1 {
 	pinctrl-0 = <&pinctrl_lpuart1>;
 	status = "okay";
 
-	bluetooth {
-		compatible = "nxp,88w8987-bt";
+	port {
+		lpuart1_ep: endpoint {
+			remote-endpoint = <&m2_e_uart_ep>;
+		};
 	};
 };
 
@@ -818,8 +842,12 @@ &pciea {
 
 &pciea_port0 {
 	reset-gpios = <&lsio_gpio4 29 GPIO_ACTIVE_LOW>;
-	vpcie-supply = <&reg_pciea>;
-	vpcie3v3aux-supply = <&reg_pciea>;
+
+	port {
+		pciea_port0_ep: endpoint {
+			remote-endpoint = <&m2_e_pcie_ep>;
+		};
+	};
 };
 
 &pcieb {
-- 
2.50.1

[PATCH V2 8/8] arm64: dts: imx8qxp-mek: Describe the PCIe M.2 Key E connector

[Sherry Sun (OSS)]

From: Sherry Sun <sherry.sun@nxp.com>

The i.MX8QXP-MEK has the PCIe M.2 Mechanical Key E connector to connect
wireless connectivity cards over PCIe and UART interfaces. Hence,
describe the connector node and link it with the PCIe b Root Port and
LPUART1 nodes through graph port/endpoint.

The M.2 Key E connector is powered by a 3.3V fixed regulator
(reg_3v3) on board.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
---
 arch/arm64/boot/dts/freescale/imx8qxp-mek.dts | 54 ++++++++++++++-----
 1 file changed, 41 insertions(+), 13 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
index a9b967d0a9be..c9fe4034cc2d 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-mek.dts
@@ -40,6 +40,37 @@ memory@80000000 {
 		reg = <0x00000000 0x80000000 0 0x40000000>;
 	};
 
+	m2-connector {
+		compatible = "pcie-m2-e-connector";
+		vpcie3v3-supply = <&reg_3v3>;
+		w-disable1-gpios = <&pca9557_a 2 GPIO_ACTIVE_LOW>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <0>;
+				m2_e_pcie_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&pcieb_port0_ep>;
+				};
+			};
+
+			port@3 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				reg = <3>;
+				m2_e_uart_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&lpuart1_ep>;
+				};
+			};
+		};
+	};
+
 	reg_usdhc2_vmmc: usdhc2-vmmc {
 		compatible = "regulator-fixed";
 		regulator-name = "SD1_SPWR";
@@ -157,15 +188,6 @@ reg_3v3: regulator-3v3 {
 		regulator-max-microvolt = <3300000>;
 	};
 
-	reg_pcieb: regulator-pcie {
-		compatible = "regulator-fixed";
-		regulator-max-microvolt = <3300000>;
-		regulator-min-microvolt = <3300000>;
-		regulator-name = "mpcie_3v3";
-		gpio = <&pca9557_a 2 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-	};
-
 	reg_audio: regulator-audio {
 		compatible = "regulator-fixed";
 		regulator-max-microvolt = <3300000>;
@@ -696,8 +718,10 @@ &lpuart1 {
 	pinctrl-0 = <&pinctrl_lpuart1>;
 	status = "okay";
 
-	bluetooth {
-		compatible = "nxp,88w8987-bt";
+	port {
+		lpuart1_ep: endpoint {
+			remote-endpoint = <&m2_e_uart_ep>;
+		};
 	};
 };
 
@@ -746,8 +770,12 @@ &pcie0_ep {
 
 &pcieb_port0 {
 	reset-gpios = <&lsio_gpio4 0 GPIO_ACTIVE_LOW>;
-	vpcie-supply = <&reg_pcieb>;
-	vpcie3v3aux-supply = <&reg_pcieb>;
+
+	port {
+		pcieb_port0_ep: endpoint {
+			remote-endpoint = <&m2_e_pcie_ep>;
+		};
+	};
 };
 
 &scu_key {
-- 
2.50.1