[PATCH v3 00/11] ARM: sunxi: add Allwinner B288 and the PocketBook Verse

[PATCH v3 00/11] ARM: sunxi: add Allwinner B288 and the PocketBook Verse

[Pablo Mazzini]

The Allwinner B288 (sun8iw10p1) is a dual Cortex-A7 SoC used in e-book
readers. This series adds the CCU and pin controller drivers, the RTC,
I2C, NMI and watchdog compatibles, the SoC .dtsi, and one board: the
PocketBook Verse (PB629), a 6" reader.

The B288 is closest to the A64: most of its PLLs are bit-identical.
The clock and pin descriptions come from Allwinner's BSP, cross-checked
against ccu-sun50i-a64.c. Tested on a PB629, boots to userspace.

The pin controller relies on "pinctrl: sunxi: dt: number the IRQ banks
from the first one that has IRQs" for correct PIO interrupt mapping.

Changes since v2:
  - Drop the MMC binding patch, applied by Ulf.
  - Rebase onto sunxi/for-next.
  - Constrain the RTC clock outputs and pinctrl interrupts in the
    bindings (Sashiko).
  - Add a B288 watchdog compatible (Andre).
  - DTS: drop the memory node, the arch timer workaround and the
    sunxi.c entry; add disable-wp and the eMMC 1.8V modes; DLDO1 no
    longer always-on; mainline pin function names (Andre).

Changes since v1:
  - Add this cover letter.
  - Drop both new bindings; add the compatibles to the existing
    allwinner,sun4i-a10-{ccu,pinctrl}.yaml instead.
  - Rewrite the pinctrl driver in the DT-provided pinmux style.

Pablo Mazzini (11):
  dt-bindings: clock: sun4i-a10-ccu: add Allwinner B288
  clk: sunxi-ng: add Allwinner B288 CCU driver
  dt-bindings: pinctrl: sun4i-a10: add Allwinner B288
  pinctrl: sunxi: add Allwinner B288 pin controller driver
  dt-bindings: rtc: sun6i-a31: add Allwinner B288
  rtc: sun6i: add Allwinner B288 compatible
  dt-bindings: i2c: mv64xxx: add Allwinner B288
  dt-bindings: interrupt-controller: add Allwinner B288 NMI
  dt-bindings: watchdog: sun4i-a10-wdt: add Allwinner B288
  dt-bindings: arm: sunxi: add PocketBook Verse
  ARM: dts: allwinner: add B288 and the PocketBook Verse

 .../devicetree/bindings/arm/sunxi.yaml        |   5 +
 .../clock/allwinner,sun4i-a10-ccu.yaml        |   1 +
 .../bindings/i2c/marvell,mv64xxx-i2c.yaml     |   1 +
 .../allwinner,sun7i-a20-sc-nmi.yaml           |   1 +
 .../pinctrl/allwinner,sun4i-a10-pinctrl.yaml  |  22 +
 .../bindings/rtc/allwinner,sun6i-a31-rtc.yaml |   3 +
 .../watchdog/allwinner,sun4i-a10-wdt.yaml     |   1 +
 arch/arm/boot/dts/allwinner/Makefile          |   1 +
 .../allwinner/sun8i-b288-pocketbook-verse.dts | 114 ++++
 arch/arm/boot/dts/allwinner/sun8i-b288.dtsi   | 290 ++++++++
 drivers/clk/sunxi-ng/Kconfig                  |   5 +
 drivers/clk/sunxi-ng/Makefile                 |   1 +
 drivers/clk/sunxi-ng/ccu-sun8i-b288.c         | 644 ++++++++++++++++++
 drivers/clk/sunxi-ng/ccu-sun8i-b288.h         |  10 +
 drivers/pinctrl/sunxi/Kconfig                 |  10 +
 drivers/pinctrl/sunxi/Makefile                |   1 +
 drivers/pinctrl/sunxi/pinctrl-sun8i-b288.c    |  49 ++
 drivers/rtc/rtc-sun6i.c                       |   1 +
 include/dt-bindings/clock/sun8i-b288-ccu.h    |  82 +++
 include/dt-bindings/reset/sun8i-b288-ccu.h    |  45 ++
 20 files changed, 1287 insertions(+)
 create mode 100644 arch/arm/boot/dts/allwinner/sun8i-b288-pocketbook-verse.dts
 create mode 100644 arch/arm/boot/dts/allwinner/sun8i-b288.dtsi
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-b288.c
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-b288.h
 create mode 100644 drivers/pinctrl/sunxi/pinctrl-sun8i-b288.c
 create mode 100644 include/dt-bindings/clock/sun8i-b288-ccu.h
 create mode 100644 include/dt-bindings/reset/sun8i-b288-ccu.h

-- 
2.52.0

[PATCH v3 01/11] dt-bindings: clock: sun4i-a10-ccu: add Allwinner B288

[Pablo Mazzini]

The B288 (sun8iw10p1) is a dual Cortex-A7 SoC used in e-book readers.
Its CCU needs only the two oscillator inputs, so it fits the existing
schema without changes.

Signed-off-by: Pablo Mazzini <pmazzini@gmail.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
---
 .../clock/allwinner,sun4i-a10-ccu.yaml        |  1 +
 include/dt-bindings/clock/sun8i-b288-ccu.h    | 82 +++++++++++++++++++
 include/dt-bindings/reset/sun8i-b288-ccu.h    | 45 ++++++++++
 3 files changed, 128 insertions(+)
 create mode 100644 include/dt-bindings/clock/sun8i-b288-ccu.h
 create mode 100644 include/dt-bindings/reset/sun8i-b288-ccu.h

diff --git a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
index 1690b9d99c3d..cc3f62d3554c 100644
--- a/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
+++ b/Documentation/devicetree/bindings/clock/allwinner,sun4i-a10-ccu.yaml
@@ -28,6 +28,7 @@ properties:
       - allwinner,sun8i-a33-ccu
       - allwinner,sun8i-a83t-ccu
       - allwinner,sun8i-a83t-r-ccu
+      - allwinner,sun8i-b288-ccu
       - allwinner,sun8i-h3-ccu
       - allwinner,sun8i-h3-r-ccu
       - allwinner,sun8i-r40-ccu
diff --git a/include/dt-bindings/clock/sun8i-b288-ccu.h b/include/dt-bindings/clock/sun8i-b288-ccu.h
new file mode 100644
index 000000000000..c9b9eaf979ad
--- /dev/null
+++ b/include/dt-bindings/clock/sun8i-b288-ccu.h
@@ -0,0 +1,82 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+#ifndef _DT_BINDINGS_CLK_SUN8I_B288_H_
+#define _DT_BINDINGS_CLK_SUN8I_B288_H_
+
+#define CLK_PLL_CPUX	0
+#define CLK_PLL_AUDIO_BASE	1
+#define CLK_PLL_VIDEO0	2
+#define CLK_PLL_DDR0	3
+#define CLK_PLL_PERIPH0	4
+#define CLK_PLL_VIDEO1	5
+#define CLK_PLL_24M	6
+#define CLK_PLL_PERIPH1	7
+#define CLK_PLL_DE	8
+#define CLK_PLL_DDR1	9
+
+#define CLK_PLL_PERIPH0_2X	10
+#define CLK_PLL_PERIPH1_2X	11
+#define CLK_CPUX	12
+#define CLK_AXI	13
+#define CLK_CPUAPB	14
+#define CLK_AHB1	15
+#define CLK_APB1	16
+#define CLK_APB2	17
+
+#define CLK_NAND	18
+#define CLK_MMC0	19
+#define CLK_MMC1	20
+#define CLK_MMC2	21
+#define CLK_MMC3	22
+#define CLK_SPI0	23
+#define CLK_SPI1	24
+#define CLK_SPI2	25
+#define CLK_DRAM	26
+#define CLK_DE	27
+#define CLK_EE	28
+#define CLK_EDMA	29
+#define CLK_TCON0	30
+#define CLK_MBUS	31
+
+#define CLK_BUS_THS	32
+#define CLK_BUS_NAND	33
+#define CLK_BUS_SDMMC0_BUS	34
+#define CLK_BUS_SDMMC1_BUS	35
+#define CLK_BUS_SDMMC2_BUS	36
+#define CLK_BUS_SDMMC3_BUS	37
+#define CLK_BUS_SPI0	38
+#define CLK_BUS_SPI1	39
+#define CLK_BUS_SPI2	40
+#define CLK_BUS_I2S0	41
+#define CLK_BUS_I2S1	42
+#define CLK_BUS_SPDIF	43
+#define CLK_BUS_DSD	44
+#define CLK_BUS_DMIC	45
+#define CLK_BUS_USBOHCI0	46
+#define CLK_BUS_USBEHCI0	47
+#define CLK_BUS_USBOTG	48
+#define CLK_BUS_DE	49
+#define CLK_BUS_EE	50
+#define CLK_BUS_TCON0	51
+#define CLK_BUS_CSI	52
+#define CLK_BUS_ADDA	53
+#define CLK_BUS_SDRAM	54
+#define CLK_BUS_PSRAM	55
+#define CLK_BUS_DMA	56
+#define CLK_BUS_UART0	57
+#define CLK_BUS_UART1	58
+#define CLK_BUS_UART2	59
+#define CLK_BUS_UART3	60
+#define CLK_BUS_UART4	61
+#define CLK_BUS_UART5	62
+#define CLK_BUS_TWI0	63
+#define CLK_BUS_TWI1	64
+#define CLK_BUS_TWI2	65
+#define CLK_BUS_PIO	66
+#define CLK_BUS_GPADC	67
+#define CLK_BUS_KEYADC	68
+#define CLK_MMC0_SAMPLE	69
+#define CLK_MMC0_OUTPUT	70
+#define CLK_MMC1_SAMPLE	71
+#define CLK_MMC1_OUTPUT	72
+
+#endif
diff --git a/include/dt-bindings/reset/sun8i-b288-ccu.h b/include/dt-bindings/reset/sun8i-b288-ccu.h
new file mode 100644
index 000000000000..675145654548
--- /dev/null
+++ b/include/dt-bindings/reset/sun8i-b288-ccu.h
@@ -0,0 +1,45 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
+#ifndef _DT_BINDINGS_RST_SUN8I_B288_H_
+#define _DT_BINDINGS_RST_SUN8I_B288_H_
+
+#define RST_BUS_THS	0
+#define RST_BUS_NAND	1
+#define RST_BUS_MMC0	2
+#define RST_BUS_MMC1	3
+#define RST_BUS_MMC2	4
+#define RST_BUS_MMC3	5
+#define RST_BUS_SPI0	6
+#define RST_BUS_SPI1	7
+#define RST_BUS_SPI2	8
+#define RST_BUS_I2S0	9
+#define RST_BUS_I2S1	10
+#define RST_BUS_SPDIF	11
+#define RST_BUS_DSD	12
+#define RST_BUS_DMIC	13
+#define RST_USBPHY0	14
+#define RST_BUS_OHCI0	15
+#define RST_BUS_EHCI0	16
+#define RST_BUS_OTG	17
+#define RST_BUS_DE	18
+#define RST_BUS_EE	19
+#define RST_BUS_TCON0	20
+#define RST_BUS_CSI	21
+#define RST_BUS_ADDA	22
+#define RST_BUS_WLAN	23
+#define RST_MBUS	24
+#define RST_BUS_DRAM	25
+#define RST_BUS_PSRAM	26
+#define RST_BUS_DMA	27
+#define RST_BUS_UART0	28
+#define RST_BUS_UART1	29
+#define RST_BUS_UART2	30
+#define RST_BUS_UART3	31
+#define RST_BUS_UART4	32
+#define RST_BUS_UART5	33
+#define RST_BUS_I2C0	34
+#define RST_BUS_I2C1	35
+#define RST_BUS_I2C2	36
+#define RST_BUS_GPADC	37
+#define RST_BUS_KEYADC	38
+
+#endif
-- 
2.52.0

[PATCH v3 02/11] clk: sunxi-ng: add Allwinner B288 CCU driver

[Pablo Mazzini]

Covers the PLLs, the CPU/AHB/APB tree, the module clocks and the bus
gates and resets.

Signed-off-by: Pablo Mazzini <pmazzini@gmail.com>
---
 drivers/clk/sunxi-ng/Kconfig          |   5 +
 drivers/clk/sunxi-ng/Makefile         |   1 +
 drivers/clk/sunxi-ng/ccu-sun8i-b288.c | 644 ++++++++++++++++++++++++++
 drivers/clk/sunxi-ng/ccu-sun8i-b288.h |  10 +
 4 files changed, 660 insertions(+)
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-b288.c
 create mode 100644 drivers/clk/sunxi-ng/ccu-sun8i-b288.h

diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 6af2d020e03e..5bdfb8574794 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -88,6 +88,11 @@ config SUN6I_RTC_CCU
 	default ARCH_SUNXI
 	depends on MACH_SUN8I || ARM64 || RISCV || COMPILE_TEST
 
+config SUN8I_B288_CCU
+	tristate "Support for the Allwinner B288 CCU"
+	default ARCH_SUNXI
+	depends on MACH_SUN8I || COMPILE_TEST
+
 config SUN8I_A23_CCU
 	tristate "Support for the Allwinner A23 CCU"
 	default ARCH_SUNXI
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index a1c4087d7241..dcc377a09ccc 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -40,6 +40,7 @@ obj-$(CONFIG_SUN4I_A10_CCU)	+= sun4i-a10-ccu.o
 obj-$(CONFIG_SUN5I_CCU)		+= sun5i-ccu.o
 obj-$(CONFIG_SUN6I_A31_CCU)	+= sun6i-a31-ccu.o
 obj-$(CONFIG_SUN6I_RTC_CCU)	+= sun6i-rtc-ccu.o
+obj-$(CONFIG_SUN8I_B288_CCU)	+= ccu-sun8i-b288.o
 obj-$(CONFIG_SUN8I_A23_CCU)	+= sun8i-a23-ccu.o
 obj-$(CONFIG_SUN8I_A33_CCU)	+= sun8i-a33-ccu.o
 obj-$(CONFIG_SUN8I_A83T_CCU)	+= sun8i-a83t-ccu.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-b288.c b/drivers/clk/sunxi-ng/ccu-sun8i-b288.c
new file mode 100644
index 000000000000..97c4f0c3238a
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-b288.c
@@ -0,0 +1,644 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Clock Control Unit driver for the Allwinner B288 (sun8iw10p1).
+ *
+ * Closely related to the A64; most of its PLLs are bit-identical.
+ * Transcribed from the BSP clk-sun8iw10.{c,h} and cross-checked against
+ * ccu-sun50i-a64.c; divergences are called out inline.
+ *
+ * The audio clock tree (i2s/spdif/dsd/dmic/adda) is not implemented.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_mult.h"
+#include "ccu_nk.h"
+#include "ccu_nkm.h"
+#include "ccu_nkmp.h"
+#include "ccu_nm.h"
+#include "ccu_phase.h"
+
+#include "ccu-sun8i-b288.h"
+
+/*
+ * PLL_CPU @ 0x000 -- N[12:8] K[5:4] M[1:0] P[17:16], gate 31, lock 28.
+ * Identical to sun50i-a64.
+ */
+static struct ccu_nkmp pll_cpux_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT(8, 5),
+	.k		= _SUNXI_CCU_MULT(4, 2),
+	.m		= _SUNXI_CCU_DIV(0, 2),
+	.p		= _SUNXI_CCU_DIV_MAX(16, 2, 4),
+	.common		= {
+		.reg		= 0x000,
+		.hw.init	= CLK_HW_INIT("pll-cpux", "osc24M",
+					      &ccu_nkmp_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+/*
+ * PLL_AUDIO @ 0x008 -- N[14:8] M[4:0], gate 31, lock 28.
+ * The vendor also writes a sigma-delta pattern at PLL_AUDIOPAT (0x284);
+ * not transcribed, so plain NM here.
+ */
+static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_audio_base_clk, "pll-audio-base",
+				   "osc24M", 0x008,
+				   8, 7,	/* N */
+				   0, 5,	/* M */
+				   BIT(31),	/* gate */
+				   BIT(28),	/* lock */
+				   CLK_SET_RATE_UNGATE);
+
+/* PLL_VIDEO0 @ 0x010 -- identical to sun50i-a64. */
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_video0_clk, "pll-video0",
+					"osc24M", 0x010,
+					8, 7,		/* N */
+					0, 4,		/* M */
+					BIT(24),	/* frac enable */
+					BIT(25),	/* frac select */
+					270000000,	/* frac rate 0 */
+					297000000,	/* frac rate 1 */
+					BIT(31),	/* gate */
+					BIT(28),	/* lock */
+					CLK_SET_RATE_UNGATE);
+
+/*
+ * PLL_DDR0 @ 0x020 -- DIVERGES FROM A64, which is NKM with N[12:8] K[5:4].
+ * The B288 has a 7-bit N and no K: the value boot0 leaves here sets
+ * bit 13, which the A64's 5-bit N field cannot hold.
+ */
+static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_ddr0_clk, "pll-ddr0",
+				   "osc24M", 0x020,
+				   8, 7,	/* N */
+				   0, 2,	/* M */
+				   BIT(31),	/* gate */
+				   BIT(28),	/* lock */
+				   CLK_SET_RATE_UNGATE);
+
+/* PLL_PERIPH0 @ 0x028 -- identical to sun50i-a64, incl. fixed post-div 2. */
+static struct ccu_nk pll_periph0_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT(8, 5),
+	.k		= _SUNXI_CCU_MULT_MIN(4, 2, 2),
+	.fixed_post_div	= 2,
+	.common		= {
+		.reg		= 0x028,
+		.features	= CCU_FEATURE_FIXED_POSTDIV,
+		.hw.init	= CLK_HW_INIT("pll-periph0", "osc24M",
+					      &ccu_nk_ops, 0),
+	},
+};
+
+/* PLL_VIDEO1 @ 0x030 -- same layout as PLL_VIDEO0. */
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_video1_clk, "pll-video1",
+					"osc24M", 0x030,
+					8, 7,		/* N */
+					0, 4,		/* M */
+					BIT(24),	/* frac enable */
+					BIT(25),	/* frac select */
+					270000000,	/* frac rate 0 */
+					297000000,	/* frac rate 1 */
+					BIT(31),	/* gate */
+					BIT(28),	/* lock */
+					CLK_SET_RATE_UNGATE);
+
+/*
+ * PLL_24M @ 0x034 -- B288 only, no a64 equivalent.
+ * Vendor: N[14:8] K[20:16] M[1:0] P[7:4]. The unusual K position means the
+ * generic NKMP macro cannot be used; declared longhand.
+ */
+static struct ccu_nkmp pll_24m_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT(8, 7),
+	.k		= _SUNXI_CCU_MULT(16, 5),
+	.m		= _SUNXI_CCU_DIV(0, 2),
+	.p		= _SUNXI_CCU_DIV(4, 4),
+	.common		= {
+		.reg		= 0x034,
+		.hw.init	= CLK_HW_INIT("pll-24m", "osc24M",
+					      &ccu_nkmp_ops,
+					      CLK_SET_RATE_UNGATE),
+	},
+};
+
+/* PLL_PERIPH1 @ 0x044 -- identical to sun50i-a64. */
+static struct ccu_nk pll_periph1_clk = {
+	.enable		= BIT(31),
+	.lock		= BIT(28),
+	.n		= _SUNXI_CCU_MULT(8, 5),
+	.k		= _SUNXI_CCU_MULT_MIN(4, 2, 2),
+	.fixed_post_div	= 2,
+	.common		= {
+		.reg		= 0x044,
+		.features	= CCU_FEATURE_FIXED_POSTDIV,
+		.hw.init	= CLK_HW_INIT("pll-periph1", "osc24M",
+					      &ccu_nk_ops, 0),
+	},
+};
+
+/* PLL_DE @ 0x048 -- identical to sun50i-a64. */
+static SUNXI_CCU_NM_WITH_FRAC_GATE_LOCK(pll_de_clk, "pll-de",
+					"osc24M", 0x048,
+					8, 7,		/* N */
+					0, 4,		/* M */
+					BIT(24),	/* frac enable */
+					BIT(25),	/* frac select */
+					270000000,	/* frac rate 0 */
+					297000000,	/* frac rate 1 */
+					BIT(31),	/* gate */
+					BIT(28),	/* lock */
+					CLK_SET_RATE_UNGATE);
+
+/* PLL_DDR1 @ 0x04c -- B288 only. Same layout; this is the one feeding DRAM. */
+static SUNXI_CCU_NM_WITH_GATE_LOCK(pll_ddr1_clk, "pll-ddr1",
+				   "osc24M", 0x04c,
+				   8, 7,	/* N */
+				   0, 2,	/* M */
+				   BIT(31),	/* gate */
+				   BIT(28),	/* lock */
+				   CLK_SET_RATE_UNGATE);
+
+/*
+ * pll_periph{0,1} carry a fixed /2 post-divider, so the 2x clocks are the
+ * raw outputs.
+ */
+static CLK_FIXED_FACTOR_HW(pll_periph0_2x_clk, "pll-periph0-2x",
+			   &pll_periph0_clk.common.hw,
+			   1, 2, 0);
+static CLK_FIXED_FACTOR_HW(pll_periph1_2x_clk, "pll-periph1-2x",
+			   &pll_periph1_clk.common.hw,
+			   1, 2, 0);
+
+/*
+ * CPU_CFG @ 0x050 -- mux[17:16], CPUAPB divider [9:8], AXI divider [1:0].
+ * Same layout as the H3 and the A64.
+ */
+static const char * const cpux_parents[] = { "osc32k", "osc24M",
+					     "pll-cpux", "pll-cpux" };
+static SUNXI_CCU_MUX(cpux_clk, "cpux", cpux_parents,
+		     0x050, 16, 2, CLK_IS_CRITICAL | CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_M(axi_clk, "axi", "cpux", 0x050, 0, 2, 0);
+static SUNXI_CCU_M(cpuapb_clk, "cpuapb", "cpux", 0x050, 8, 2, 0);
+
+/*
+ * AHB1_CFG @ 0x054 -- mux[13:12], AHB1 P2 divider [5:4], PLL_PERIPH0-only
+ * pre-divider [7:6], APB1 divider [9:8].
+ */
+static const char * const ahb1_parents[] = { "osc32k", "osc24M",
+					     "axi", "pll-periph0" };
+static const struct ccu_mux_var_prediv ahb1_predivs[] = {
+	{ .index = 3, .shift = 6, .width = 2 },
+};
+
+static struct ccu_div ahb1_clk = {
+	.div		= _SUNXI_CCU_DIV_FLAGS(4, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+	.mux		= {
+		.shift	= 12,
+		.width	= 2,
+
+		.var_predivs	= ahb1_predivs,
+		.n_var_predivs	= ARRAY_SIZE(ahb1_predivs),
+	},
+
+	.common		= {
+		.reg		= 0x054,
+		.features	= CCU_FEATURE_VARIABLE_PREDIV,
+		.hw.init	= CLK_HW_INIT_PARENTS("ahb1",
+						      ahb1_parents,
+						      &ccu_div_ops,
+						      0),
+	},
+};
+
+static struct clk_div_table apb1_div_table[] = {
+	{ .val = 0, .div = 2 },
+	{ .val = 1, .div = 2 },
+	{ .val = 2, .div = 4 },
+	{ .val = 3, .div = 8 },
+	{ /* Sentinel */ },
+};
+
+static SUNXI_CCU_DIV_TABLE(apb1_clk, "apb1", "ahb1",
+			   0x054, 8, 2, apb1_div_table, 0);
+
+/*
+ * APB2_CFG @ 0x058 -- M[4:0] P[17:16] mux[25:24]. The divider matches the
+ * H3, but mux index 2 selects PLL_24M here rather than PLL_PERIPH0_2X.
+ */
+static const char * const apb2_parents[] = { "osc32k", "osc24M",
+					     "pll-24m", "pll-periph0-2x" };
+static SUNXI_CCU_MP_WITH_MUX(apb2_clk, "apb2", apb2_parents, 0x058,
+			     0, 5,	/* M */
+			     16, 2,	/* P */
+			     24, 2,	/* mux */
+			     0);
+
+static const char * const mod0_parents[] = { "osc24M", "pll-periph0-2x",
+					     "pll-periph1-2x" };
+static const char * const de_parents[] = { "pll-periph0-2x", "pll-de" };
+static const char * const tcon0_parents[] = { "pll-video0", "pll-video1" };
+static const char * const mbus_parents[] = { "osc24M", "pll-periph0-2x",
+					     "pll-ddr0", "pll-ddr1" };
+static const char * const dram_parents[] = { "pll-ddr0", "pll-ddr1",
+					     "pll-periph0-2x" };
+
+/* NAND_CFG @ 0x080 -- M[3:0] P[17:16] mux[25:24] gate 31 */
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand_clk, "nand", mod0_parents, 0x080,
+				  0, 4,		/* M */
+				  16, 2,	/* P */
+				  24, 2,	/* mux */
+				  BIT(31),	/* gate */
+				  0);
+
+/*
+ * SD{0..3}_CFG @ 0x088/0x08c/0x090/0x094 -- same layout as NAND.
+ * mmc0/mmc1 use the old timing mode: no post-divider, and they need the
+ * sample and output phase clocks. mmc2/mmc3 halve the clock internally.
+ */
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc0_clk, "mmc0", mod0_parents, 0x088,
+				  0, 4,		/* M */
+				  16, 2,	/* P */
+				  24, 2,	/* mux */
+				  BIT(31),	/* gate */
+				  0);
+static SUNXI_CCU_PHASE(mmc0_sample_clk, "mmc0_sample", "mmc0", 0x088, 20, 3, 0);
+static SUNXI_CCU_PHASE(mmc0_output_clk, "mmc0_output", "mmc0", 0x088, 8, 3, 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc1_clk, "mmc1", mod0_parents, 0x08c,
+				  0, 4,		/* M */
+				  16, 2,	/* P */
+				  24, 2,	/* mux */
+				  BIT(31),	/* gate */
+				  0);
+static SUNXI_CCU_PHASE(mmc1_sample_clk, "mmc1_sample", "mmc1", 0x08c, 20, 3, 0);
+static SUNXI_CCU_PHASE(mmc1_output_clk, "mmc1_output", "mmc1", 0x08c, 8, 3, 0);
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc2_clk, "mmc2", mod0_parents,
+					  0x090, 0, 4, 16, 2, 24, 2,
+					  BIT(31), 2, 0);
+static SUNXI_CCU_MP_WITH_MUX_GATE_POSTDIV(mmc3_clk, "mmc3", mod0_parents,
+					  0x094, 0, 4, 16, 2, 24, 2,
+					  BIT(31), 2, 0);
+
+/* SPI{0..2}_CFG @ 0x0a0/0x0a4/0x0a8 -- same layout as NAND. */
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", mod0_parents, 0x0a0,
+				  0, 4, 16, 2, 24, 2, BIT(31), 0);
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", mod0_parents, 0x0a4,
+				  0, 4, 16, 2, 24, 2, BIT(31), 0);
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi2_clk, "spi2", mod0_parents, 0x0a8,
+				  0, 4, 16, 2, 24, 2, BIT(31), 0);
+
+/* DRAM_CFG @ 0x0f4 -- M[1:0] mux[21:20] gate 31 */
+static SUNXI_CCU_M_WITH_MUX_GATE(dram_clk, "dram", dram_parents, 0x0f4,
+				 0, 2,		/* M */
+				 20, 2,		/* mux */
+				 BIT(31),	/* gate */
+				 CLK_IS_CRITICAL);
+
+/* DE_CFG @ 0x104, EE_CFG @ 0x108, EDMA_CFG @ 0x10c -- M[3:0] mux[26:24] gate 31 */
+static SUNXI_CCU_M_WITH_MUX_GATE(de_clk, "de", de_parents, 0x104,
+				 0, 4, 24, 3, BIT(31), CLK_SET_RATE_PARENT);
+static SUNXI_CCU_M_WITH_MUX_GATE(ee_clk, "ee", de_parents, 0x108,
+				 0, 4, 24, 3, BIT(31), CLK_SET_RATE_PARENT);
+static SUNXI_CCU_M_WITH_MUX_GATE(edma_clk, "edma", de_parents, 0x10c,
+				 0, 4, 24, 3, BIT(31), CLK_SET_RATE_PARENT);
+
+/* TCON_CFG @ 0x118 -- mux[26:24] gate 31, no divider */
+static SUNXI_CCU_MUX_WITH_GATE(tcon0_clk, "tcon0", tcon0_parents, 0x118,
+			       24, 3,		/* mux */
+			       BIT(31),		/* gate */
+			       CLK_SET_RATE_PARENT);
+
+/* MBUS_CFG @ 0x15c -- M[2:0] mux[25:24] gate 31 */
+static SUNXI_CCU_M_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents, 0x15c,
+				 0, 3, 24, 2, BIT(31), CLK_IS_CRITICAL);
+
+static SUNXI_CCU_GATE(bus_ths_clk, "bus-ths", "apb1",
+		      0x068, BIT(8), 0);
+static SUNXI_CCU_GATE(bus_nand_clk, "bus-nand", "ahb1",
+		      0x060, BIT(13), 0);
+static SUNXI_CCU_GATE(bus_sdmmc0_bus_clk, "bus-sdmmc0-bus", "ahb1",
+		      0x060, BIT(8), 0);
+static SUNXI_CCU_GATE(bus_sdmmc1_bus_clk, "bus-sdmmc1-bus", "ahb1",
+		      0x060, BIT(9), 0);
+static SUNXI_CCU_GATE(bus_sdmmc2_bus_clk, "bus-sdmmc2-bus", "ahb1",
+		      0x060, BIT(10), 0);
+static SUNXI_CCU_GATE(bus_sdmmc3_bus_clk, "bus-sdmmc3-bus", "ahb1",
+		      0x060, BIT(11), 0);
+static SUNXI_CCU_GATE(bus_spi0_clk, "bus-spi0", "ahb1",
+		      0x060, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_spi1_clk, "bus-spi1", "ahb1",
+		      0x060, BIT(21), 0);
+static SUNXI_CCU_GATE(bus_spi2_clk, "bus-spi2", "ahb1",
+		      0x060, BIT(22), 0);
+static SUNXI_CCU_GATE(bus_i2s0_clk, "bus-i2s0", "apb1",
+		      0x068, BIT(12), 0);
+static SUNXI_CCU_GATE(bus_i2s1_clk, "bus-i2s1", "apb1",
+		      0x068, BIT(13), 0);
+static SUNXI_CCU_GATE(bus_spdif_clk, "bus-spdif", "apb1",
+		      0x068, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_dsd_clk, "bus-dsd", "apb1",
+		      0x068, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_dmic_clk, "bus-dmic", "apb1",
+		      0x068, BIT(3), 0);
+static SUNXI_CCU_GATE(bus_usbohci0_clk, "bus-usbohci0", "ahb1",
+		      0x060, BIT(29), 0);
+static SUNXI_CCU_GATE(bus_usbehci0_clk, "bus-usbehci0", "ahb1",
+		      0x060, BIT(26), 0);
+static SUNXI_CCU_GATE(bus_usbotg_clk, "bus-usbotg", "ahb1",
+		      0x060, BIT(24), 0);
+static SUNXI_CCU_GATE(bus_de_clk, "bus-de", "ahb1",
+		      0x064, BIT(12), 0);
+static SUNXI_CCU_GATE(bus_ee_clk, "bus-ee", "ahb1",
+		      0x064, BIT(13), 0);
+static SUNXI_CCU_GATE(bus_tcon0_clk, "bus-tcon0", "ahb1",
+		      0x064, BIT(4), 0);
+/* csi_s, csi_m and csi_misc share one bus gate, as on the A64. */
+static SUNXI_CCU_GATE(bus_csi_clk, "bus-csi", "ahb1",
+		      0x064, BIT(8), 0);
+static SUNXI_CCU_GATE(bus_adda_clk, "bus-adda", "apb1",
+		      0x068, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_sdram_clk, "bus-sdram", "ahb1",
+		      0x060, BIT(14), 0);
+static SUNXI_CCU_GATE(bus_psram_clk, "bus-psram", "ahb1",
+		      0x060, BIT(15), 0);
+static SUNXI_CCU_GATE(bus_dma_clk, "bus-dma", "ahb1",
+		      0x060, BIT(6), 0);
+static SUNXI_CCU_GATE(bus_uart0_clk, "bus-uart0", "apb2",
+		      0x06c, BIT(16), 0);
+static SUNXI_CCU_GATE(bus_uart1_clk, "bus-uart1", "apb2",
+		      0x06c, BIT(17), 0);
+static SUNXI_CCU_GATE(bus_uart2_clk, "bus-uart2", "apb2",
+		      0x06c, BIT(18), 0);
+static SUNXI_CCU_GATE(bus_uart3_clk, "bus-uart3", "apb2",
+		      0x06c, BIT(19), 0);
+static SUNXI_CCU_GATE(bus_uart4_clk, "bus-uart4", "apb2",
+		      0x06c, BIT(20), 0);
+static SUNXI_CCU_GATE(bus_uart5_clk, "bus-uart5", "apb2",
+		      0x06c, BIT(21), 0);
+static SUNXI_CCU_GATE(bus_twi0_clk, "bus-twi0", "apb2",
+		      0x06c, BIT(0), 0);
+static SUNXI_CCU_GATE(bus_twi1_clk, "bus-twi1", "apb2",
+		      0x06c, BIT(1), 0);
+static SUNXI_CCU_GATE(bus_twi2_clk, "bus-twi2", "apb2",
+		      0x06c, BIT(2), 0);
+static SUNXI_CCU_GATE(bus_pio_clk, "bus-pio", "apb1",
+		      0x068, BIT(5), 0);
+static SUNXI_CCU_GATE(bus_gpadc_clk, "bus-gpadc", "apb1",
+		      0x068, BIT(10), 0);
+static SUNXI_CCU_GATE(bus_keyadc_clk, "bus-keyadc", "apb1",
+		      0x068, BIT(9), 0);
+/* losc_out is the RTC's osc32k-out */
+
+static const struct ccu_reset_map sun8i_b288_ccu_resets[] = {
+	[RST_BUS_THS]	= { 0x2d0, BIT(8) },
+	[RST_BUS_NAND]	= { 0x2c0, BIT(13) },
+	[RST_BUS_MMC0]	= { 0x2c0, BIT(8) },
+	[RST_BUS_MMC1]	= { 0x2c0, BIT(9) },
+	[RST_BUS_MMC2]	= { 0x2c0, BIT(10) },
+	[RST_BUS_MMC3]	= { 0x2c0, BIT(11) },
+	[RST_BUS_SPI0]	= { 0x2c0, BIT(20) },
+	[RST_BUS_SPI1]	= { 0x2c0, BIT(21) },
+	[RST_BUS_SPI2]	= { 0x2c0, BIT(22) },
+	[RST_BUS_I2S0]	= { 0x2d0, BIT(12) },
+	[RST_BUS_I2S1]	= { 0x2d0, BIT(13) },
+	[RST_BUS_SPDIF]	= { 0x2d0, BIT(1) },
+	[RST_BUS_DSD]	= { 0x2d0, BIT(2) },
+	[RST_BUS_DMIC]	= { 0x2d0, BIT(3) },
+	[RST_USBPHY0]	= { 0x0cc, BIT(0) },
+	[RST_BUS_OHCI0]	= { 0x2c0, BIT(29) },
+	[RST_BUS_EHCI0]	= { 0x2c0, BIT(26) },
+	[RST_BUS_OTG]	= { 0x2c0, BIT(24) },
+	[RST_BUS_DE]	= { 0x2c4, BIT(12) },
+	[RST_BUS_EE]	= { 0x2c4, BIT(13) },
+	[RST_BUS_TCON0]	= { 0x2c4, BIT(4) },
+	[RST_BUS_CSI]	= { 0x2c4, BIT(8) },
+	[RST_BUS_ADDA]	= { 0x2d0, BIT(0) },
+	[RST_BUS_WLAN]	= { 0x2c4, BIT(1) },
+	[RST_MBUS]	= { 0x0fc, BIT(31) },
+	[RST_BUS_DRAM]	= { 0x2c0, BIT(14) },
+	[RST_BUS_PSRAM]	= { 0x2c0, BIT(15) },
+	[RST_BUS_DMA]	= { 0x2c0, BIT(6) },
+	[RST_BUS_UART0]	= { 0x2d8, BIT(16) },
+	[RST_BUS_UART1]	= { 0x2d8, BIT(17) },
+	[RST_BUS_UART2]	= { 0x2d8, BIT(18) },
+	[RST_BUS_UART3]	= { 0x2d8, BIT(19) },
+	[RST_BUS_UART4]	= { 0x2d8, BIT(20) },
+	[RST_BUS_UART5]	= { 0x2d8, BIT(21) },
+	[RST_BUS_I2C0]	= { 0x2d8, BIT(0) },
+	[RST_BUS_I2C1]	= { 0x2d8, BIT(1) },
+	[RST_BUS_I2C2]	= { 0x2d8, BIT(2) },
+	[RST_BUS_GPADC]	= { 0x2d0, BIT(10) },
+	[RST_BUS_KEYADC]	= { 0x2d0, BIT(9) },
+};
+
+static struct ccu_common *sun8i_b288_ccu_clks[] = {
+	&pll_cpux_clk.common,
+	&pll_audio_base_clk.common,
+	&pll_video0_clk.common,
+	&pll_ddr0_clk.common,
+	&pll_periph0_clk.common,
+	&pll_video1_clk.common,
+	&pll_24m_clk.common,
+	&pll_periph1_clk.common,
+	&pll_de_clk.common,
+	&pll_ddr1_clk.common,
+	&cpux_clk.common,
+	&axi_clk.common,
+	&cpuapb_clk.common,
+	&ahb1_clk.common,
+	&apb1_clk.common,
+	&apb2_clk.common,
+	&nand_clk.common,
+	&mmc0_clk.common,
+	&mmc0_sample_clk.common,
+	&mmc0_output_clk.common,
+	&mmc1_clk.common,
+	&mmc1_sample_clk.common,
+	&mmc1_output_clk.common,
+	&mmc2_clk.common,
+	&mmc3_clk.common,
+	&spi0_clk.common,
+	&spi1_clk.common,
+	&spi2_clk.common,
+	&dram_clk.common,
+	&de_clk.common,
+	&ee_clk.common,
+	&edma_clk.common,
+	&tcon0_clk.common,
+	&mbus_clk.common,
+	&bus_ths_clk.common,
+	&bus_nand_clk.common,
+	&bus_sdmmc0_bus_clk.common,
+	&bus_sdmmc1_bus_clk.common,
+	&bus_sdmmc2_bus_clk.common,
+	&bus_sdmmc3_bus_clk.common,
+	&bus_spi0_clk.common,
+	&bus_spi1_clk.common,
+	&bus_spi2_clk.common,
+	&bus_i2s0_clk.common,
+	&bus_i2s1_clk.common,
+	&bus_spdif_clk.common,
+	&bus_dsd_clk.common,
+	&bus_dmic_clk.common,
+	&bus_usbohci0_clk.common,
+	&bus_usbehci0_clk.common,
+	&bus_usbotg_clk.common,
+	&bus_de_clk.common,
+	&bus_ee_clk.common,
+	&bus_tcon0_clk.common,
+	&bus_csi_clk.common,
+	&bus_adda_clk.common,
+	&bus_sdram_clk.common,
+	&bus_psram_clk.common,
+	&bus_dma_clk.common,
+	&bus_uart0_clk.common,
+	&bus_uart1_clk.common,
+	&bus_uart2_clk.common,
+	&bus_uart3_clk.common,
+	&bus_uart4_clk.common,
+	&bus_uart5_clk.common,
+	&bus_twi0_clk.common,
+	&bus_twi1_clk.common,
+	&bus_twi2_clk.common,
+	&bus_pio_clk.common,
+	&bus_gpadc_clk.common,
+	&bus_keyadc_clk.common,
+};
+
+static struct clk_hw_onecell_data sun8i_b288_hw_clks = {
+	.hws	= {
+		[CLK_PLL_CPUX]		= &pll_cpux_clk.common.hw,
+		[CLK_PLL_AUDIO_BASE]	= &pll_audio_base_clk.common.hw,
+		[CLK_PLL_VIDEO0]	= &pll_video0_clk.common.hw,
+		[CLK_PLL_DDR0]		= &pll_ddr0_clk.common.hw,
+		[CLK_PLL_PERIPH0]	= &pll_periph0_clk.common.hw,
+		[CLK_PLL_VIDEO1]	= &pll_video1_clk.common.hw,
+		[CLK_PLL_24M]		= &pll_24m_clk.common.hw,
+		[CLK_PLL_PERIPH1]	= &pll_periph1_clk.common.hw,
+		[CLK_PLL_DE]		= &pll_de_clk.common.hw,
+		[CLK_PLL_DDR1]		= &pll_ddr1_clk.common.hw,
+		[CLK_PLL_PERIPH0_2X]	= &pll_periph0_2x_clk.hw,
+		[CLK_PLL_PERIPH1_2X]	= &pll_periph1_2x_clk.hw,
+		[CLK_CPUX]	= &cpux_clk.common.hw,
+		[CLK_AXI]	= &axi_clk.common.hw,
+		[CLK_CPUAPB]	= &cpuapb_clk.common.hw,
+		[CLK_AHB1]	= &ahb1_clk.common.hw,
+		[CLK_APB1]	= &apb1_clk.common.hw,
+		[CLK_APB2]	= &apb2_clk.common.hw,
+		[CLK_NAND]	= &nand_clk.common.hw,
+		[CLK_MMC0]	= &mmc0_clk.common.hw,
+		[CLK_MMC0_SAMPLE]	= &mmc0_sample_clk.common.hw,
+		[CLK_MMC0_OUTPUT]	= &mmc0_output_clk.common.hw,
+		[CLK_MMC1]	= &mmc1_clk.common.hw,
+		[CLK_MMC1_SAMPLE]	= &mmc1_sample_clk.common.hw,
+		[CLK_MMC1_OUTPUT]	= &mmc1_output_clk.common.hw,
+		[CLK_MMC2]	= &mmc2_clk.common.hw,
+		[CLK_MMC3]	= &mmc3_clk.common.hw,
+		[CLK_SPI0]	= &spi0_clk.common.hw,
+		[CLK_SPI1]	= &spi1_clk.common.hw,
+		[CLK_SPI2]	= &spi2_clk.common.hw,
+		[CLK_DRAM]	= &dram_clk.common.hw,
+		[CLK_DE]	= &de_clk.common.hw,
+		[CLK_EE]	= &ee_clk.common.hw,
+		[CLK_EDMA]	= &edma_clk.common.hw,
+		[CLK_TCON0]	= &tcon0_clk.common.hw,
+		[CLK_MBUS]	= &mbus_clk.common.hw,
+		[CLK_BUS_THS]	= &bus_ths_clk.common.hw,
+		[CLK_BUS_NAND]	= &bus_nand_clk.common.hw,
+		[CLK_BUS_SDMMC0_BUS]	= &bus_sdmmc0_bus_clk.common.hw,
+		[CLK_BUS_SDMMC1_BUS]	= &bus_sdmmc1_bus_clk.common.hw,
+		[CLK_BUS_SDMMC2_BUS]	= &bus_sdmmc2_bus_clk.common.hw,
+		[CLK_BUS_SDMMC3_BUS]	= &bus_sdmmc3_bus_clk.common.hw,
+		[CLK_BUS_SPI0]	= &bus_spi0_clk.common.hw,
+		[CLK_BUS_SPI1]	= &bus_spi1_clk.common.hw,
+		[CLK_BUS_SPI2]	= &bus_spi2_clk.common.hw,
+		[CLK_BUS_I2S0]	= &bus_i2s0_clk.common.hw,
+		[CLK_BUS_I2S1]	= &bus_i2s1_clk.common.hw,
+		[CLK_BUS_SPDIF]	= &bus_spdif_clk.common.hw,
+		[CLK_BUS_DSD]	= &bus_dsd_clk.common.hw,
+		[CLK_BUS_DMIC]	= &bus_dmic_clk.common.hw,
+		[CLK_BUS_USBOHCI0]	= &bus_usbohci0_clk.common.hw,
+		[CLK_BUS_USBEHCI0]	= &bus_usbehci0_clk.common.hw,
+		[CLK_BUS_USBOTG]	= &bus_usbotg_clk.common.hw,
+		[CLK_BUS_DE]	= &bus_de_clk.common.hw,
+		[CLK_BUS_EE]	= &bus_ee_clk.common.hw,
+		[CLK_BUS_TCON0]	= &bus_tcon0_clk.common.hw,
+		[CLK_BUS_CSI]		= &bus_csi_clk.common.hw,
+		[CLK_BUS_ADDA]	= &bus_adda_clk.common.hw,
+		[CLK_BUS_SDRAM]	= &bus_sdram_clk.common.hw,
+		[CLK_BUS_PSRAM]	= &bus_psram_clk.common.hw,
+		[CLK_BUS_DMA]	= &bus_dma_clk.common.hw,
+		[CLK_BUS_UART0]	= &bus_uart0_clk.common.hw,
+		[CLK_BUS_UART1]	= &bus_uart1_clk.common.hw,
+		[CLK_BUS_UART2]	= &bus_uart2_clk.common.hw,
+		[CLK_BUS_UART3]	= &bus_uart3_clk.common.hw,
+		[CLK_BUS_UART4]	= &bus_uart4_clk.common.hw,
+		[CLK_BUS_UART5]	= &bus_uart5_clk.common.hw,
+		[CLK_BUS_TWI0]	= &bus_twi0_clk.common.hw,
+		[CLK_BUS_TWI1]	= &bus_twi1_clk.common.hw,
+		[CLK_BUS_TWI2]	= &bus_twi2_clk.common.hw,
+		[CLK_BUS_PIO]	= &bus_pio_clk.common.hw,
+		[CLK_BUS_GPADC]	= &bus_gpadc_clk.common.hw,
+		[CLK_BUS_KEYADC]	= &bus_keyadc_clk.common.hw,
+	},
+	.num	= CLK_NUMBER,
+};
+
+static const struct sunxi_ccu_desc sun8i_b288_ccu_desc = {
+	.ccu_clks	= sun8i_b288_ccu_clks,
+	.num_ccu_clks	= ARRAY_SIZE(sun8i_b288_ccu_clks),
+
+	.hw_clks	= &sun8i_b288_hw_clks,
+
+	.resets		= sun8i_b288_ccu_resets,
+	.num_resets	= ARRAY_SIZE(sun8i_b288_ccu_resets),
+
+};
+
+static int sun8i_b288_ccu_probe(struct platform_device *pdev)
+{
+	void __iomem *reg;
+
+	reg = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(reg))
+		return PTR_ERR(reg);
+
+	return devm_sunxi_ccu_probe(&pdev->dev, reg, &sun8i_b288_ccu_desc);
+}
+
+static const struct of_device_id sun8i_b288_ccu_ids[] = {
+	{ .compatible = "allwinner,sun8i-b288-ccu" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, sun8i_b288_ccu_ids);
+
+static struct platform_driver sun8i_b288_ccu_driver = {
+	.probe	= sun8i_b288_ccu_probe,
+	.driver	= {
+		.name			= "sun8i-b288-ccu",
+		.suppress_bind_attrs	= true,
+		.of_match_table		= sun8i_b288_ccu_ids,
+	},
+};
+module_platform_driver(sun8i_b288_ccu_driver);
+
+MODULE_IMPORT_NS("SUNXI_CCU");
+MODULE_DESCRIPTION("Allwinner B288 (sun8iw10p1) CCU driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/clk/sunxi-ng/ccu-sun8i-b288.h b/drivers/clk/sunxi-ng/ccu-sun8i-b288.h
new file mode 100644
index 000000000000..805df2d6d99c
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun8i-b288.h
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef _CCU_SUN8I_B288_H_
+#define _CCU_SUN8I_B288_H_
+
+#include <dt-bindings/clock/sun8i-b288-ccu.h>
+#include <dt-bindings/reset/sun8i-b288-ccu.h>
+
+#define CLK_NUMBER		(CLK_MMC1_OUTPUT + 1)
+
+#endif /* _CCU_SUN8I_B288_H_ */
-- 
2.52.0