From: Jonathan Cameron <Jonathan.Cameron@Huawei.com>
To: Alison Schofield <alison.schofield@intel.com>
Cc: <linux-cxl@vger.kernel.org>,
Vishal Verma <vishal.l.verma@intel.com>,
Ira Weiny <ira.weiny@intel.com>,
Dan Williams <dan.j.williams@intel.com>, <linuxarm@huawei.com>
Subject: Re: [PATCH] cxl/pci: Set the device timestamp
Date: Fri, 27 Jan 2023 09:59:30 +0000 [thread overview]
Message-ID: <20230127095930.00000748@Huawei.com> (raw)
In-Reply-To: <20230127095906.000074ea@Huawei.com>
On Fri, 27 Jan 2023 09:59:06 +0000
Jonathan Cameron <Jonathan.Cameron@Huawei.com> wrote:
> On Thu, 26 Jan 2023 11:59:21 -0800
> Alison Schofield <alison.schofield@intel.com> wrote:
>
> > On Thu, Jan 26, 2023 at 06:04:58PM +0000, Jonathan Cameron wrote:
> > > CXL r3.0 section 8.2.9.4.2 "Set Timestamp" recommends that the host sets
> > > the timestamp after every Conventional or CXL Reset to ensure accurate
> > > timestamps. This should include on initial boot up. The time base that
> > > is being set is used by a device for the poison list overflow timestamp
> > > and all event timestamps. Note that the command is optional and if
> > > not supported and the device cannot return accurate timestamps it will
> > > fill the fields in with an appropriate marker (see the specification
> > > description of each timestamp).
> > >
> > > Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
> > >
> > > ---
> > >
> > > Open question: Should we only do this if Linux has control of the
> > > error handling? In theory it should be safe anyway given the
> > > specification is clear that the timestamp base should always be the
> > > same - so subject to small errors we shouldn't cause any firmware first
> > > handling to get confused.
> > >
> > > drivers/cxl/core/mbox.c | 25 +++++++++++++++++++++++++
> > > drivers/cxl/cxlmem.h | 7 +++++++
> > > drivers/cxl/pci.c | 5 +++++
> > > include/uapi/linux/cxl_mem.h | 1 +
> > > 4 files changed, 38 insertions(+)
> > >
> > > diff --git a/drivers/cxl/core/mbox.c b/drivers/cxl/core/mbox.c
> > > index b03fba212799..a7317bb142ed 100644
> > > --- a/drivers/cxl/core/mbox.c
> > > +++ b/drivers/cxl/core/mbox.c
> > > @@ -65,6 +65,7 @@ static struct cxl_mem_command cxl_mem_commands[CXL_MEM_COMMAND_ID_MAX] = {
> > > CXL_CMD(GET_SCAN_MEDIA_CAPS, 0x10, 0x4, 0),
> > > CXL_CMD(SCAN_MEDIA, 0x11, 0, 0),
> > > CXL_CMD(GET_SCAN_MEDIA, 0, CXL_VARIABLE_PAYLOAD, 0),
> > > + CXL_CMD(SET_TIMESTAMP, 8, 0, 0),
> > > };
> > >
> > > /*
> > > @@ -93,6 +94,7 @@ static u16 cxl_disabled_raw_commands[] = {
> > > CXL_MBOX_OP_SET_SHUTDOWN_STATE,
> > > CXL_MBOX_OP_SCAN_MEDIA,
> > > CXL_MBOX_OP_GET_SCAN_MEDIA,
> > > + CXL_MBOX_OP_SET_TIMESTAMP,
> > > };
> > >
> > > /*
> > > @@ -857,6 +859,29 @@ int cxl_mem_create_range_info(struct cxl_dev_state *cxlds)
> > > }
> > > EXPORT_SYMBOL_NS_GPL(cxl_mem_create_range_info, CXL);
> > >
> > > +int cxl_set_timestamp(struct cxl_dev_state *cxlds, u64 ts)
> > > +{
> > > + struct cxl_mbox_cmd mbox_cmd;
> > > + struct cxl_mbox_set_timestamp_in pi;
> > > +
> > > + /*
> > > + * Command is optional and functionality should not be affected if
> > > + * the command is not available.
> > > + */
> > > + if (!test_bit(CXL_MEM_COMMAND_ID_SET_TIMESTAMP, cxlds->enabled_cmds))
> > > + return 0;
> >
> > Jonathan,
> >
> > Would it be more efficient to call ktime_get_real_ns() right here,
> > rather than pass in the call from cxl_pci_probe()?
>
> Dave raised that as well. Makes sense for now. I was wildly conjecturing
> that we might want clock skew tweaking sometime in the future if the timestamps
> ever matter for much beyond error records.
Davidlohr that is!
>
> Thanks,
>
> Jonathan
>
>
> >
> > Alison
> > > +
> > > + pi.timestamp = ts;
> > > + mbox_cmd = (struct cxl_mbox_cmd) {
> > > + .opcode = CXL_MBOX_OP_SET_TIMESTAMP,
> > > + .size_in = sizeof(pi),
> > > + .payload_in = &pi,
> > > + };
> > > +
> > > + return cxl_internal_send_cmd(cxlds, &mbox_cmd);
> > > +}
> > > +EXPORT_SYMBOL_NS_GPL(cxl_set_timestamp, CXL);
> > > +
> > > struct cxl_dev_state *cxl_dev_state_create(struct device *dev)
> > > {
> > > struct cxl_dev_state *cxlds;
> > > diff --git a/drivers/cxl/cxlmem.h b/drivers/cxl/cxlmem.h
> > > index ab138004f644..0ca7a35de893 100644
> > > --- a/drivers/cxl/cxlmem.h
> > > +++ b/drivers/cxl/cxlmem.h
> > > @@ -274,6 +274,7 @@ enum cxl_opcode {
> > > CXL_MBOX_OP_RAW = CXL_MBOX_OP_INVALID,
> > > CXL_MBOX_OP_GET_FW_INFO = 0x0200,
> > > CXL_MBOX_OP_ACTIVATE_FW = 0x0202,
> > > + CXL_MBOX_OP_SET_TIMESTAMP = 0x0301,
> > > CXL_MBOX_OP_GET_SUPPORTED_LOGS = 0x0400,
> > > CXL_MBOX_OP_GET_LOG = 0x0401,
> > > CXL_MBOX_OP_IDENTIFY = 0x4000,
> > > @@ -372,6 +373,11 @@ struct cxl_mbox_set_partition_info {
> > >
> > > #define CXL_SET_PARTITION_IMMEDIATE_FLAG BIT(0)
> > >
> > > +/* Set Timestamp CXL 3.0 Spec 8.2.9.4.2 */
> > > +struct cxl_mbox_set_timestamp_in {
> > > + __le64 timestamp;
> > > +} __packed;
> > > +
> > > /**
> > > * struct cxl_mem_command - Driver representation of a memory device command
> > > * @info: Command information as it exists for the UAPI
> > > @@ -441,6 +447,7 @@ int cxl_mem_create_range_info(struct cxl_dev_state *cxlds);
> > > struct cxl_dev_state *cxl_dev_state_create(struct device *dev);
> > > void set_exclusive_cxl_commands(struct cxl_dev_state *cxlds, unsigned long *cmds);
> > > void clear_exclusive_cxl_commands(struct cxl_dev_state *cxlds, unsigned long *cmds);
> > > +int cxl_set_timestamp(struct cxl_dev_state *cxlds, u64 ts);
> > > #ifdef CONFIG_CXL_SUSPEND
> > > void cxl_mem_active_inc(void);
> > > void cxl_mem_active_dec(void);
> > > diff --git a/drivers/cxl/pci.c b/drivers/cxl/pci.c
> > > index 2bbebbc7e032..30a2b231d970 100644
> > > --- a/drivers/cxl/pci.c
> > > +++ b/drivers/cxl/pci.c
> > > @@ -2,6 +2,7 @@
> > > /* Copyright(c) 2020 Intel Corporation. All rights reserved. */
> > > #include <linux/io-64-nonatomic-lo-hi.h>
> > > #include <linux/moduleparam.h>
> > > +#include <linux/timekeeping.h>
> > > #include <linux/module.h>
> > > #include <linux/delay.h>
> > > #include <linux/sizes.h>
> > > @@ -482,6 +483,10 @@ static int cxl_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
> > > if (rc)
> > > return rc;
> > >
> > > + rc = cxl_set_timestamp(cxlds, ktime_get_real_ns());
> > > + if (rc)
> > > + return rc;
> > > +
> > > rc = cxl_dev_state_identify(cxlds);
> > > if (rc)
> > > return rc;
> > > diff --git a/include/uapi/linux/cxl_mem.h b/include/uapi/linux/cxl_mem.h
> > > index c71021a2a9ed..333301037b74 100644
> > > --- a/include/uapi/linux/cxl_mem.h
> > > +++ b/include/uapi/linux/cxl_mem.h
> > > @@ -41,6 +41,7 @@
> > > ___C(GET_SCAN_MEDIA_CAPS, "Get Scan Media Capabilities"), \
> > > ___C(SCAN_MEDIA, "Scan Media"), \
> > > ___C(GET_SCAN_MEDIA, "Get Scan Media Results"), \
> > > + ___C(SET_TIMESTAMP, "Set Device Timestamp"), \
> > > ___C(MAX, "invalid / last command")
> > >
> > > #define ___C(a, b) CXL_MEM_COMMAND_ID_##a
> > >
> > > base-commit: 172738bbccdb4ef76bdd72fc72a315c741c39161
> > > --
> > > 2.37.2
> > >
>
next prev parent reply other threads:[~2023-01-27 9:59 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-01-26 18:04 [PATCH] cxl/pci: Set the device timestamp Jonathan Cameron
2023-01-26 18:56 ` Davidlohr Bueso
2023-01-27 9:57 ` Jonathan Cameron
2023-01-27 12:08 ` Jonathan Cameron
2023-01-26 19:59 ` Alison Schofield
2023-01-27 9:59 ` Jonathan Cameron
2023-01-27 9:59 ` Jonathan Cameron [this message]
2023-01-26 20:22 ` Dan Williams
2023-01-27 10:04 ` Jonathan Cameron
2023-01-27 12:10 ` Jonathan Cameron
2023-01-27 19:07 ` Dan Williams
2023-01-27 23:50 ` Ira Weiny
2023-01-28 0:17 ` Dan Williams
2023-01-28 11:21 ` kernel test robot
2023-01-28 11:32 ` kernel test robot
2023-01-30 15:10 ` Jonathan Cameron
2023-01-28 16:01 ` kernel test robot
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20230127095930.00000748@Huawei.com \
--to=jonathan.cameron@huawei.com \
--cc=alison.schofield@intel.com \
--cc=dan.j.williams@intel.com \
--cc=ira.weiny@intel.com \
--cc=linux-cxl@vger.kernel.org \
--cc=linuxarm@huawei.com \
--cc=vishal.l.verma@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox