[PATCH v4 0/5] arm64: dts: qcom: add QCS8550 RB5Gen2 support

[PATCH v4 0/5] arm64: dts: qcom: add QCS8550 RB5Gen2 support

[Joe Sandom via B4 Relay]

This series adds device tree support for the Thundercomm RB5Gen2
development kit, based on the Qualcomm QCS8550 chipset.

Patches 1-3 prepares for the RB5gen2 device tree by adding MHI register
regions and port labels to the PCIe controller nodes, as well as moving
common IPA properties into sm8550.dtsi. Then update the existing HDK
and QRD board files accordingly.

Patches 4-5 add the dt-bindings documentation and the board device tree
for the RB5Gen2. This initial submission covers the main board; the vision
mezzanine will be supported in a follow-up series.

Product page:
https://www.thundercomm.com/product/qualcomm-rb5-gen-2-development-kit

Signed-off-by: Joe Sandom <jsandom@axon.com>
---
Changes in v4:
- Renamed LT9611 regulator nodes from lt9611-regulator-* to
  regulator-lt9611-* to follow standard naming convention
- Moved pmic-glink node before regulators to match alphabetical
  ordering used by sm8550-hdk.dts
- Reordered sound dai-link sub-nodes: codec before cpu
- Added comma separation between pinctrl-0 phandle references
  (lt9611 and tc9563 entries)
- Changed firmware paths from qcom/qcs8550/ to qcom/sm8550/ for
  adsp, cdsp, modem, IPA and GPU to keep all firmware in the same
  subdirectory
- Link to v3: https://lore.kernel.org/r/20260409-rb5gen2-dts-v3-0-be736355d4b4@axon.com

Changes in v3:
- Reworded MHI commit message to describe actual usage (debugfs
  link_transition_count) per Neil's feedback
- Reordered pinctrl-0 before pinctrl-names file-wide per Konrad's
  feedback
- Removed output-high from lt9611_rst_pin since the driver handles
  reset sequencing
- Reordered tlmm pinctrl entries by GPIO number
- Changed bias-pull-up to bias-disable for regulator enable pins
  (upd_1p05_en, upd_3p3_en) since these are active-high enables
- Added comments for gpio-reserved-ranges explaining GPIOs 32-35
  are for NFC secure element and 36-39 for fingerprint sensor
- Removed max-sd-hs-hz override since upstream clock driver already
  provides the correct 37.5MHz frequency
- Updated msi-map deletion rationale with root cause: Gunyah limits
  ITS device mappings to two per root complex on SM8550
- Link to v2: https://lore.kernel.org/r/20260407-rb5gen2-dts-v2-0-d0c7f447ee73@axon.com

Changes in v2:
- Lowercase hex in MHI region definitions for pcie0 and pcie1 nodes +
  vertical alignment
- Change pcie0 and pcie1 reg-names for one entry per line
- Ensured pcie port labels + changes to sm8550-hdk.dts and sm8550-qrd.dts
  are done in a single commit
- Moved IPA gsi-loader and memory-region to sm8550.dtsi since they are common
  properties. Reflect changes in sm8550-hdk.dts and sm8550-qrd.dts
- Removed usbhub_reset since this is not required
- Added swctrl-gpios property to wcn7850-pmu
- Split sw_ctrl_default gpio from bt_default grouping and referenced the
  pinctrl separately
- Replaced upd_reset regulator-fixed with pinctrl and vddpe-3v3-supply
  on pcie0
- Aligned firmware-name values vertically on the quote mark
- Changed cdsp, adsp and modem remoteprocs to .mbn file type instead of
  .mdt
- Added remark in rb5gen2 dts commit explaining the rationale for
  deleting msi-map in pcie0 and pcie1 nodes
- Link to v1: https://lore.kernel.org/r/20260404-rb5gen2-dts-v1-0-895f8fc494fc@axon.com

---
Joe Sandom (5):
      arm64: dts: qcom: sm8550: add PCIe MHI register regions
      arm64: dts: qcom: sm8550: add PCIe port labels
      arm64: dts: qcom: sm8550: move IPA properties to SoC device tree
      dt-bindings: arm: qcom: document QCS8550 RB5Gen2 board
      arm64: dts: qcom: qcs8550: add QCS8550 RB5Gen2 board support

 Documentation/devicetree/bindings/arm/qcom.yaml |    6 +
 arch/arm64/boot/dts/qcom/Makefile               |    1 +
 arch/arm64/boot/dts/qcom/qcs8550-rb5gen2.dts    | 1573 +++++++++++++++++++++++
 arch/arm64/boot/dts/qcom/sm8550-hdk.dts         |    4 +-
 arch/arm64/boot/dts/qcom/sm8550-qrd.dts         |    4 +-
 arch/arm64/boot/dts/qcom/sm8550.dtsi            |   26 +-
 6 files changed, 1602 insertions(+), 12 deletions(-)
---
base-commit: af241225893ac4933bb8f0615f2dfda8ea2326ce
change-id: 20260404-rb5gen2-dts-180cde0b716c

Best regards,
-- 
Joe Sandom <jsandom@axon.com>

[PATCH v4 1/5] arm64: dts: qcom: sm8550: add PCIe MHI register regions

[Joe Sandom via B4 Relay]

From: Joe Sandom <jsandom@axon.com>

Add the MHI register regions to the pcie0 and pcie1 controller nodes
to expose link power state transition counters (L0s/L1/L1.1/L1.2/L2)
via debugfs. The PCIe host driver uses this region to read the
link_transition_count from the MHI registers.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Joe Sandom <jsandom@axon.com>
---
 arch/arm64/boot/dts/qcom/sm8550.dtsi | 20 ++++++++++++++++----
 1 file changed, 16 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 912525e9bca6f5e1cbb8887ee0bf9e39650dc4ff..055ca931c04859f3a312eb9921aeb7a8cc676822 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -1964,8 +1964,14 @@ pcie0: pcie@1c00000 {
 			      <0 0x60000000 0 0xf1d>,
 			      <0 0x60000f20 0 0xa8>,
 			      <0 0x60001000 0 0x1000>,
-			      <0 0x60100000 0 0x100000>;
-			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			      <0 0x60100000 0 0x100000>,
+			      <0 0x01c03000 0 0x1000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "config",
+				    "mhi";
 			#address-cells = <3>;
 			#size-cells = <2>;
 			ranges = <0x01000000 0x0 0x00000000 0x0 0x60200000 0x0 0x100000>,
@@ -2138,8 +2144,14 @@ pcie1: pcie@1c08000 {
 			      <0x0 0x40000000 0x0 0xf1d>,
 			      <0x0 0x40000f20 0x0 0xa8>,
 			      <0x0 0x40001000 0x0 0x1000>,
-			      <0x0 0x40100000 0x0 0x100000>;
-			reg-names = "parf", "dbi", "elbi", "atu", "config";
+			      <0x0 0x40100000 0x0 0x100000>,
+			      <0x0 0x01c0b000 0x0 0x1000>;
+			reg-names = "parf",
+				    "dbi",
+				    "elbi",
+				    "atu",
+				    "config",
+				    "mhi";
 			#address-cells = <3>;
 			#size-cells = <2>;
 			ranges = <0x01000000 0x0 0x00000000 0x0 0x40200000 0x0 0x100000>,

-- 
2.34.1

[PATCH v4 2/5] arm64: dts: qcom: sm8550: add PCIe port labels

[Joe Sandom via B4 Relay]

From: Joe Sandom <jsandom@axon.com>

Add labels to the root port nodes (pcie0_port0, pcie1_port0) to
allow board DTS files to reference them for adding endpoint devices
to each pcie root port.

Update the pcieport0 reference to pcie0_port0 in sm8550-hdk.dts and
sm8550-qrd.dts to match the label rename in sm8550.dtsi.

Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Joe Sandom <jsandom@axon.com>
---
 arch/arm64/boot/dts/qcom/sm8550-hdk.dts | 2 +-
 arch/arm64/boot/dts/qcom/sm8550-qrd.dts | 2 +-
 arch/arm64/boot/dts/qcom/sm8550.dtsi    | 4 ++--
 3 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
index ee13e6136a8259d28540e718851e094f74ead278..e821b731bdc496c872703723df02ae9b9b0233b5 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
@@ -1012,7 +1012,7 @@ &pcie0 {
 	status = "okay";
 };
 
-&pcieport0 {
+&pcie0_port0 {
 	wifi@0 {
 		compatible = "pci17cb,1107";
 		reg = <0x10000 0x0 0x0 0x0 0x0>;
diff --git a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
index 2fb2e0be5e4c6b597f20f332cdf063daa2664205..cf63109ff7bf7b6fc827f108e22e82b8b04273c1 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
@@ -912,7 +912,7 @@ &pcie0 {
 	status = "okay";
 };
 
-&pcieport0 {
+&pcie0_port0 {
 	wifi@0 {
 		compatible = "pci17cb,1107";
 		reg = <0x10000 0x0 0x0 0x0 0x0>;
diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 055ca931c04859f3a312eb9921aeb7a8cc676822..54308cbde40732da072177eab533582c155df590 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -2098,7 +2098,7 @@ opp-16000000-3 {
 				};
 			};
 
-			pcieport0: pcie@0 {
+			pcie0_port0: pcie@0 {
 				device_type = "pci";
 				reg = <0x0 0x0 0x0 0x0 0x0>;
 				bus-range = <0x01 0xff>;
@@ -2300,7 +2300,7 @@ opp-32000000-4 {
 				};
 			};
 
-			pcie@0 {
+			pcie1_port0: pcie@0 {
 				device_type = "pci";
 				reg = <0x0 0x0 0x0 0x0 0x0>;
 				bus-range = <0x01 0xff>;

-- 
2.34.1

[PATCH v4 3/5] arm64: dts: qcom: sm8550: move IPA properties to SoC device tree

[Joe Sandom via B4 Relay]

From: Joe Sandom <jsandom@axon.com>

Move qcom,gsi-loader and memory-region properties from individual board
DTS files into the SoC DTSI, since these are common to all SM8550-based
boards.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Joe Sandom <jsandom@axon.com>
---
 arch/arm64/boot/dts/qcom/sm8550-hdk.dts | 2 --
 arch/arm64/boot/dts/qcom/sm8550-qrd.dts | 2 --
 arch/arm64/boot/dts/qcom/sm8550.dtsi    | 2 ++
 3 files changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
index e821b731bdc496c872703723df02ae9b9b0233b5..b795589385520acd74eecc7701cab82f4f7da200 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
@@ -939,8 +939,6 @@ &i2c_master_hub_0 {
 };
 
 &ipa {
-	qcom,gsi-loader = "self";
-	memory-region = <&ipa_fw_mem>;
 	firmware-name = "qcom/sm8550/ipa_fws.mbn";
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
index cf63109ff7bf7b6fc827f108e22e82b8b04273c1..f2effa55d8197819175bfd5a89d2fddb20561548 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
@@ -818,8 +818,6 @@ fsa4480_sbu_mux: endpoint {
 };
 
 &ipa {
-	qcom,gsi-loader = "self";
-	memory-region = <&ipa_fw_mem>;
 	firmware-name = "qcom/sm8550/ipa_fws.mbn";
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 54308cbde40732da072177eab533582c155df590..d292dfce6b66fff6cff918b8bd6ac0b9cd22c4b3 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -2730,6 +2730,8 @@ &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
 			qcom,smem-state-names = "ipa-clock-enabled-valid",
 						"ipa-clock-enabled";
 
+			qcom,gsi-loader = "self";
+			memory-region = <&ipa_fw_mem>;
 			sram = <&ipa_modem_tables>;
 
 			status = "disabled";

-- 
2.34.1

[PATCH v4 4/5] dt-bindings: arm: qcom: document QCS8550 RB5Gen2 board

[Joe Sandom via B4 Relay]

From: Joe Sandom <jsandom@axon.com>

Document the Qualcomm RB5gen2 from Thundercomm based on the
QCS8550 chipset from Qualcomm.

[1] https://www.thundercomm.com/product/qualcomm-rb5-gen-2-development-kit/

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Joe Sandom <jsandom@axon.com>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 1335a7bee397c46e8dc62806091531e32b7327d4..f9f8001e3e6b66e3a926255bdb15363f4c7c2b66 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1093,6 +1093,12 @@ properties:
           - const: qcom,qcs8550
           - const: qcom,sm8550
 
+      - items:
+          - enum:
+              - qcom,qcs8550-rb5gen2
+          - const: qcom,qcs8550
+          - const: qcom,sm8550
+
       - items:
           - enum:
               - ayaneo,pocket-s2

-- 
2.34.1

[PATCH v4 5/5] arm64: dts: qcom: qcs8550: add QCS8550 RB5Gen2 board support

[Joe Sandom via B4 Relay]

From: Joe Sandom <jsandom@axon.com>

The RB5gen2 is an embedded development platform for the
QCS8550, based on the Snapdragon 8 Gen 2 SoC (SM8550).

This change implements the main board, the vision mezzanine
will be supported in a follow up patch.

The main board has the following features:
- Qualcomm Dragonwing QCS8550 SoC
- Adreno GPU 740
- Spectra ISP
- Adreno VPU 8550
- Adreno DPU 1295
- 1 x 1GbE Ethernet (USB Ethernet)
- WIFI 7 + Bluetooth 5.4
- 1 x USB 2.0 Micro B (Debug)
- 1 x USB 3.0 Type C (ADB, DP out)
- 2 x USB 3.0 Type A
- 1 x HDMI 1.4 Type A
- 1 x DP 1.4 Type C
- 2 x WSA8845 Speaker amplifiers
- 2 x Speaker connectors
- 1 x On Board PDM MIC
- Accelerometer + Gyro Sensor
- 96Boards compatible low-speed and high-speed connectors [1]
- 7 x LED indicators (4 user, 2 radio, 1 power)
- Buttons for power, volume up/down, force USB boot
- 3 x Dip switches

On-Board PMICs:
- PMK8550 2.1
- PM8550 2.0
- PM8550VS 2.0 x4
- PM8550VE 2.0
- PM8550B 2.0
- PMR735D 2.0
- PM8010 1.1 x2

Product Page: [2]

[1] https://www.96boards.org/specifications/
[2] https://www.thundercomm.com/product/qualcomm-rb5-gen-2-development-kit

The default msi-map from sm8550.dtsi is deleted for both pcie0 and
pcie1. The QPS615 PCIe switch on each port exposes more than two
devices (1 USP + 3 DSPs), but Gunyah currently limits ITS device
mappings to two per root complex to save memory. With msi-map
present, the ITS MAPD command times out.

Deleting msi-map causes the DWC controller to fall back to its
internal iMSI-RX module, which handles MSIs without this limitation.

Signed-off-by: Joe Sandom <jsandom@axon.com>
---
 arch/arm64/boot/dts/qcom/Makefile            |    1 +
 arch/arm64/boot/dts/qcom/qcs8550-rb5gen2.dts | 1573 ++++++++++++++++++++++++++
 2 files changed, 1574 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 4ba8e73064194926096b98b9556a3207e8f24d72..f8c65771f76629d7fafee15ac8d7bb62cd24a20f 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -184,6 +184,7 @@ qcs8300-ride-el2-dtbs := qcs8300-ride.dtb monaco-el2.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8300-ride-el2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-aim300-aiot.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-rb5gen2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride-r3.dtb
 
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-rb5gen2.dts b/arch/arm64/boot/dts/qcom/qcs8550-rb5gen2.dts
new file mode 100644
index 0000000000000000000000000000000000000000..9df8dcd6c62b680ea7b6180489dddb6c6045486b
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-rb5gen2.dts
@@ -0,0 +1,1573 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2026 Axon Enterprise, Inc.
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qcs8550.dtsi"
+#include "pm8010.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550b.dtsi"
+#define PMK8550VE_SID 5
+#include "pm8550ve.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+#include "pmr735d_a.dtsi"
+#include "pmr735d_b.dtsi"
+
+/ {
+	model = "Qualcomm Technologies, Inc. QCS8550 RB5Gen2";
+	compatible = "qcom,qcs8550-rb5gen2", "qcom,qcs8550", "qcom,sm8550";
+	chassis-type = "embedded";
+
+	aliases {
+		serial0 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	clocks {
+		clk40m: can-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <40000000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&volume_up_n>;
+		pinctrl-names = "default";
+
+		key-volume-up {
+			label = "Volume Up";
+			linux,code = <KEY_VOLUMEUP>;
+			gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	hdmi-connector {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con: endpoint {
+				remote-endpoint = <&lt9611_out>;
+			};
+		};
+	};
+
+	/* Lontium LT9611UXC fails FW upgrade and has timeouts with geni-i2c */
+	/* Workaround is to use bit-banged I2C */
+	i2c_hub_3_gpio: i2c {
+		compatible = "i2c-gpio";
+
+		sda-gpios = <&tlmm 22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-0 {
+			label = "green:status-3";
+			function = LED_FUNCTION_STATUS;
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&pm8550_gpios 2 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led-1 {
+			label = "blue:bt-power";
+			function = LED_FUNCTION_BLUETOOTH;
+			color = <LED_COLOR_ID_BLUE>;
+			gpios = <&pm8550b_gpios 7 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "bluetooth-power";
+			default-state = "off";
+		};
+
+		led-2 {
+			label = "yellow:wlan";
+			function = LED_FUNCTION_WLAN;
+			color = <LED_COLOR_ID_YELLOW>;
+			gpios = <&pm8550b_gpios 9 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "phy0tx";
+			default-state = "off";
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&redriver_usb_con_ss>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_sbu_in: endpoint {
+						remote-endpoint = <&redriver_usb_con_sbu>;
+					};
+				};
+			};
+		};
+	};
+
+	lt9611_1v2: regulator-lt9611-1v2 {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_1V2";
+
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+
+		vin-supply = <&vreg_l14b_3p2>;
+	};
+
+	lt9611_3v3: regulator-lt9611-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "LT9611_3V3";
+
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		vin-supply = <&vreg_l14b_3p2>;
+	};
+
+	pcie_upd_1p05: regulator-pcie-upd-1p05 {
+		compatible = "regulator-fixed";
+		regulator-name = "PCIE_UPD_1P05";
+		gpio = <&tlmm 179 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&vdd_ntn_0p9>;
+		regulator-min-microvolt = <1050000>;
+		regulator-max-microvolt = <1050000>;
+		enable-active-high;
+		regulator-enable-ramp-delay = <5000>;
+		pinctrl-0 = <&upd_1p05_en>;
+		pinctrl-names = "default";
+	};
+
+	pcie_upd_3p3: regulator-pcie-upd-3p3 {
+		compatible = "regulator-fixed";
+		regulator-name = "PCIE_UPD_3P3";
+		gpio = <&tlmm 13 GPIO_ACTIVE_HIGH>;
+		vin-supply = <&pcie_upd_1p05>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		regulator-enable-ramp-delay = <10000>;
+		pinctrl-0 = <&upd_3p3_en>;
+		pinctrl-names = "default";
+	};
+
+	vdd_ntn_0p9: regulator-vdd-ntn-0p9 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_NTN_0P9";
+		vin-supply = <&vdd_ntn_1p8>;
+		regulator-min-microvolt = <899400>;
+		regulator-max-microvolt = <899400>;
+		regulator-enable-ramp-delay = <4300>;
+	};
+
+	vdd_ntn_1p8: regulator-vdd-ntn-1p8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_NTN_1P8";
+		gpio = <&tlmm 67 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		pinctrl-0 = <&ntn0_en>;
+		pinctrl-names = "default";
+		regulator-enable-ramp-delay = <10000>;
+	};
+
+	vdd_ntn1_0p9: regulator-vdd-ntn1-0p9 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_NTN1_0P9";
+		vin-supply = <&vdd_ntn1_1p8>;
+		regulator-min-microvolt = <899400>;
+		regulator-max-microvolt = <899400>;
+		regulator-enable-ramp-delay = <4300>;
+	};
+
+	vdd_ntn1_1p8: regulator-vdd-ntn1-1p8 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_NTN1_1P8";
+		gpio = <&tlmm 42 GPIO_ACTIVE_HIGH>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		enable-active-high;
+		pinctrl-0 = <&ntn1_en>;
+		pinctrl-names = "default";
+		regulator-enable-ramp-delay = <10000>;
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	sound {
+		compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
+		model = "QCS8550-RB5Gen2";
+		audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
+				"SpkrRight IN", "WSA_SPK2 OUT",
+				"VA DMIC0", "vdd-micb",
+				"VA DMIC1", "vdd-micb";
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			codec {
+				sound-dai = <&left_spkr>, <&right_spkr>,
+					    <&swr0 0>, <&lpass_wsamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		pinctrl-0 = <&wlan_en>, <&bt_default>, <&sw_ctrl_default>,
+			    <&pmk8550_sleep_clk>;
+		pinctrl-names = "default";
+
+		wlan-enable-gpios = <&tlmm 80 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+		swctrl-gpios = <&tlmm 82 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&vreg_s5g_0p85>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_s2g_0p852>;
+		vdddig-supply = <&vreg_s4e_0p95>;
+		vddrfa1p2-supply = <&vreg_s4g_1p25>;
+		vddrfa1p8-supply = <&vreg_s6g_1p86>;
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob1>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l11-supply = <&vreg_s4g_1p25>;
+		vdd-l12-supply = <&vreg_s6g_1p86>;
+		vdd-l15-supply = <&vreg_s6g_1p86>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2720000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1b_1p8: ldo1 {
+			regulator-name = "vreg_l1b_1p8";
+			regulator-min-microvolt = <1710000>;
+			regulator-max-microvolt = <1950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <2900000>;
+			regulator-max-microvolt = <3544000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p1: ldo5 {
+			regulator-name = "vreg_l5b_3p1";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_1p8: ldo7 {
+			regulator-name = "vreg_l7b_1p8";
+			regulator-min-microvolt = <1700000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_1p8: ldo8 {
+			regulator-name = "vreg_l8b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l11b_1p2: ldo11 {
+			regulator-name = "vreg_l11b_1p2";
+			regulator-min-microvolt = <1100000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p8: ldo12 {
+			regulator-name = "vreg_l12b_1p8";
+			regulator-min-microvolt = <1710000>;
+			regulator-max-microvolt = <1950000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <2700000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p2: ldo14 {
+			regulator-name = "vreg_l14b_3p2";
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1760000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l16b_2p8: ldo16 {
+			regulator-name = "vreg_l16b_2p8";
+			regulator-min-microvolt = <2000000>;
+			regulator-max-microvolt = <3400000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2400000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s4g_1p25>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+
+		vreg_l3c_0p9: ldo3 {
+			regulator-name = "vreg_l3c_0p9";
+			regulator-min-microvolt = <835000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vreg_l1d_0p88: ldo1 {
+			regulator-name = "vreg_l1d_0p88";
+			regulator-min-microvolt = <825000>;
+			regulator-max-microvolt = <958000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2d_0p752: ldo2 {
+			regulator-name = "vreg_l2d_0p752";
+			regulator-min-microvolt = <675000>;
+			regulator-max-microvolt = <808000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4d_0p628: smps4 {
+			regulator-name = "vreg_s4d_0p628";
+			regulator-min-microvolt = <572000>;
+			regulator-max-microvolt = <988000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5d_0p728: smps5 {
+			regulator-name = "vreg_s5d_0p728";
+			regulator-min-microvolt = <572000>;
+			regulator-max-microvolt = <988000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+
+		vreg_l1e_0p88: ldo1 {
+			regulator-name = "vreg_l1e_0p88";
+			regulator-min-microvolt = <831000>;
+			regulator-max-microvolt = <904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2e_0p9: ldo2 {
+			regulator-name = "vreg_l2e_0p9";
+			regulator-min-microvolt = <870000>;
+			regulator-max-microvolt = <970000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s1e_0p72: smps1 {
+			regulator-name = "vreg_s1e_0p72";
+			regulator-min-microvolt = <532000>;
+			regulator-max-microvolt = <852000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s3e_0p75: smps3 {
+			regulator-name = "vreg_s3e_0p75";
+			regulator-min-microvolt = <716000>;
+			regulator-max-microvolt = <884000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4e_0p95: smps4 {
+			regulator-name = "vreg_s4e_0p95";
+			regulator-min-microvolt = <870100>;
+			regulator-max-microvolt = <1152000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5e_1p08: smps5 {
+			regulator-name = "vreg_s5e_1p08";
+			regulator-min-microvolt = <1010000>;
+			regulator-max-microvolt = <1120000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s6e_0p728: smps6 {
+			regulator-name = "vreg_s6e_0p728";
+			regulator-min-microvolt = <528000>;
+			regulator-max-microvolt = <904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s7-supply = <&vph_pwr>;
+
+		vreg_l1f_0p9: ldo1 {
+			regulator-name = "vreg_l1f_0p9";
+			regulator-min-microvolt = <866000>;
+			regulator-max-microvolt = <958000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_0p88: ldo2 {
+			regulator-name = "vreg_l2f_0p88";
+			regulator-min-microvolt = <866000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_0p88: ldo3 {
+			regulator-name = "vreg_l3f_0p88";
+			regulator-min-microvolt = <830000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s1f_0p728: smps1 {
+			regulator-name = "vreg_s1f_0p728";
+			regulator-min-microvolt = <516000>;
+			regulator-max-microvolt = <904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s3f_0p852: smps3 {
+			regulator-name = "vreg_s3f_0p852";
+			regulator-min-microvolt = <688000>;
+			regulator-max-microvolt = <952000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4f_0p5: smps4 {
+			regulator-name = "vreg_s4f_0p5";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <500000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5f_0p752: smps5 {
+			regulator-name = "vreg_s5f_0p752";
+			regulator-min-microvolt = <716000>;
+			regulator-max-microvolt = <884000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s7f_0p628: smps7 {
+			regulator-name = "vreg_s7f_0p628";
+			regulator-min-microvolt = <516000>;
+			regulator-max-microvolt = <812000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-5 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "g";
+
+		vdd-l1-supply = <&vreg_s4g_1p25>;
+		vdd-l2-supply = <&vreg_s4g_1p25>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+
+		vreg_l1g_1p2: ldo1 {
+			regulator-name = "vreg_l1g_1p2";
+			regulator-min-microvolt = <1140000>;
+			regulator-max-microvolt = <1260000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3g_1p2: ldo3 {
+			regulator-name = "vreg_l3g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s1g_1p256: smps1 {
+			regulator-name = "vreg_s1g_1p256";
+			regulator-min-microvolt = <1172000>;
+			regulator-max-microvolt = <1388000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2g_0p852: smps2 {
+			regulator-name = "vreg_s2g_0p852";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1053200>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s3g_0p752: smps3 {
+			regulator-name = "vreg_s3g_0p752";
+			regulator-min-microvolt = <532000>;
+			regulator-max-microvolt = <1148000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4g_1p25: smps4 {
+			regulator-name = "vreg_s4g_1p25";
+			regulator-min-microvolt = <1172000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5g_0p85: smps5 {
+			regulator-name = "vreg_s5g_0p85";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1002600>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s6g_1p86: smps6 {
+			regulator-name = "vreg_s6g_1p86";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2192000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-6 {
+		compatible = "qcom,pm8010-rpmh-regulators";
+
+		vdd-l1-l2-supply = <&vreg_s4g_1p25>;
+		vdd-l3-l4-supply = <&vreg_bob2>;
+		vdd-l5-supply = <&vreg_s6g_1p86>;
+		vdd-l6-supply = <&vreg_s6g_1p86>;
+		vdd-l7-supply = <&vreg_bob1>;
+
+		qcom,pmic-id = "m";
+
+		vreg_l1m_1p056: ldo1 {
+			regulator-name = "vreg_l1m_1p056";
+			regulator-min-microvolt = <1056000>;
+			regulator-max-microvolt = <1056000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2m_1p056: ldo2 {
+			regulator-name = "vreg_l2m_1p056";
+			regulator-min-microvolt = <1056000>;
+			regulator-max-microvolt = <1056000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3m_2p8: ldo3 {
+			regulator-name = "vreg_l3m_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4m_2p8: ldo4 {
+			regulator-name = "vreg_l4m_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5m_1p8: ldo5 {
+			regulator-name = "vreg_l5m_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6m_1p8: ldo6 {
+			regulator-name = "vreg_l6m_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7m_2p9: ldo7 {
+			regulator-name = "vreg_l7m_2p9";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2904000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-7 {
+		compatible = "qcom,pm8010-rpmh-regulators";
+
+		vdd-l1-l2-supply = <&vreg_s4g_1p25>;
+		vdd-l3-l4-supply = <&vreg_bob2>;
+		vdd-l5-supply = <&vreg_s6g_1p86>;
+		vdd-l6-supply = <&vreg_bob1>;
+		vdd-l7-supply = <&vreg_bob1>;
+
+		qcom,pmic-id = "n";
+
+		vreg_l1n_1p1: ldo1 {
+			regulator-name = "vreg_l1n_1p1";
+			regulator-min-microvolt = <1104000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2n_1p1: ldo2 {
+			regulator-name = "vreg_l2n_1p1";
+			regulator-min-microvolt = <1104000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3n_2p8: ldo3 {
+			regulator-name = "vreg_l3n_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4n_2p8: ldo4 {
+			regulator-name = "vreg_l4n_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5n_1p8: ldo5 {
+			regulator-name = "vreg_l5n_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6n_3p3: ldo6 {
+			regulator-name = "vreg_l6n_3p3";
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7n_2p96: ldo7 {
+			regulator-name = "vreg_l7n_2p96";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&gpi_dma2 {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/sm8550/a740_zap.mbn";
+};
+
+&i2c_hub_2 {
+	clock-frequency = <100000>;
+
+	status = "okay";
+
+	typec-mux@1c {
+		compatible = "onnn,nb7vpq904m";
+		reg = <0x1c>;
+
+		vcc-supply = <&vreg_l15b_1p8>;
+
+		retimer-switch;
+		orientation-switch;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				redriver_usb_con_ss: endpoint {
+					remote-endpoint = <&pmic_glink_ss_in>;
+				};
+			};
+
+			port@1 {
+				reg = <1>;
+
+				redriver_phy_con_ss: endpoint {
+					remote-endpoint = <&usb_dp_qmpphy_out>;
+					data-lanes = <0 1 2 3>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				redriver_usb_con_sbu: endpoint {
+					remote-endpoint = <&pmic_glink_sbu_in>;
+				};
+			};
+		};
+	};
+};
+
+&i2c_hub_3_gpio {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	lt9611_codec: hdmi-bridge@2b {
+		compatible = "lontium,lt9611uxc";
+		reg = <0x2b>;
+
+		interrupts-extended = <&tlmm 40 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>;
+
+		vdd-supply = <&lt9611_1v2>;
+		vcc-supply = <&lt9611_3v3>;
+
+		pinctrl-0 = <&lt9611_irq_pin>, <&lt9611_rst_pin>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				lt9611_a: endpoint {
+					remote-endpoint = <&mdss_dsi0_out>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				lt9611_out: endpoint {
+					remote-endpoint = <&hdmi_con>;
+				};
+			};
+		};
+	};
+};
+
+&i2c_hub_4 {
+	status = "okay";
+};
+
+&i2c_master_hub_0 {
+	status = "okay";
+};
+
+&ipa {
+	firmware-name = "qcom/sm8550/ipa_fws.mbn";
+
+	status = "okay";
+};
+
+&iris {
+	status = "okay";
+};
+
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>;
+	pinctrl-names = "default";
+
+	qcom,dmic-sample-rate = <4800000>;
+
+	vdd-micb-supply = <&vreg_l15b_1p8>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dsi0 {
+	vdda-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&mdss_dsi0_out {
+	remote-endpoint = <&lt9611_a>;
+	data-lanes = <0 1 2 3>;
+};
+
+&mdss_dsi0_phy {
+	vdds-supply = <&vreg_l1e_0p88>;
+
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&pcie0 {
+	vddpe-3v3-supply = <&pcie_upd_3p3>;
+
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie0_default_state>;
+	pinctrl-names = "default";
+
+	iommu-map = <0x0 &apps_smmu 0x1400 0x1>,
+		    <0x100 &apps_smmu 0x1401 0x1>,
+		    <0x208 &apps_smmu 0x1402 0x1>,
+		    <0x210 &apps_smmu 0x1403 0x1>,
+		    <0x218 &apps_smmu 0x1404 0x1>,
+		    <0x300 &apps_smmu 0x1407 0x1>,
+		    <0x400 &apps_smmu 0x1408 0x1>,
+		    <0x500 &apps_smmu 0x140c 0x1>,
+		    <0x501 &apps_smmu 0x140e 0x1>;
+
+	/delete-property/ msi-map;
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1e_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie0_port0 {
+	pcie@0,0 {
+		compatible = "pci1179,0623";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		device_type = "pci";
+		ranges;
+		bus-range = <0x2 0xff>;
+
+		vddc-supply = <&vdd_ntn_0p9>;
+		vdd18-supply = <&vdd_ntn_1p8>;
+		vdd09-supply = <&vdd_ntn_0p9>;
+		vddio1-supply = <&vdd_ntn_1p8>;
+		vddio2-supply = <&vdd_ntn_1p8>;
+		vddio18-supply = <&vdd_ntn_1p8>;
+
+		i2c-parent = <&i2c_hub_4 0x77>;
+
+		resx-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&tc9563_0_rst>, <&upd_ponrst>;
+		pinctrl-names = "default";
+
+		pcie@1,0 {
+			reg = <0x20800 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			device_type = "pci";
+			ranges;
+			bus-range = <0x3 0xff>;
+		};
+
+		pcie@2,0 {
+			reg = <0x21000 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			device_type = "pci";
+			ranges;
+			bus-range = <0x4 0xff>;
+		};
+
+		pcie@3,0 {
+			reg = <0x21800 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges;
+			bus-range = <0x5 0xff>;
+
+			pci@0,0 {
+				reg = <0x50000 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
+				ranges;
+			};
+
+			pci@0,1 {
+				reg = <0x50100 0x0 0x0 0x0 0x0>;
+				#address-cells = <3>;
+				#size-cells = <2>;
+				device_type = "pci";
+				ranges;
+			};
+		};
+	};
+};
+
+&pcie1 {
+	wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie1_default_state>;
+	pinctrl-names = "default";
+
+	iommu-map = <0x0 &apps_smmu 0x1480 0x1>,
+		    <0x100 &apps_smmu 0x1481 0x1>,
+		    <0x208 &apps_smmu 0x1482 0x1>,
+		    <0x210 &apps_smmu 0x1483 0x1>,
+		    <0x218 &apps_smmu 0x1484 0x1>,
+		    <0x300 &apps_smmu 0x1487 0x1>,
+		    <0x400 &apps_smmu 0x1488 0x1>,
+		    <0x500 &apps_smmu 0x148c 0x1>,
+		    <0x501 &apps_smmu 0x148e 0x1>;
+
+	/delete-property/ msi-map;
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l3c_0p9>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	vdda-qref-supply = <&vreg_l1e_0p88>;
+
+	status = "okay";
+};
+
+&pcie1_port0 {
+	pcie@0,0 {
+		compatible = "pci1179,0623";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+
+		device_type = "pci";
+		ranges;
+		bus-range = <0x2 0xff>;
+
+		vddc-supply = <&vdd_ntn1_0p9>;
+		vdd18-supply = <&vdd_ntn1_1p8>;
+		vdd09-supply = <&vdd_ntn1_0p9>;
+		vddio1-supply = <&vdd_ntn1_1p8>;
+		vddio2-supply = <&vdd_ntn1_1p8>;
+		vddio18-supply = <&vdd_ntn1_1p8>;
+
+		i2c-parent = <&i2c_hub_3_gpio 0x77>;
+
+		resx-gpios = <&tlmm 65 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&tc9563_1_rst>;
+		pinctrl-names = "default";
+
+		pcie@1,0 {
+			reg = <0x20800 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			device_type = "pci";
+			ranges;
+			bus-range = <0x3 0xff>;
+		};
+
+		pcie@2,0 {
+			reg = <0x21000 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+
+			device_type = "pci";
+			ranges;
+			bus-range = <0x4 0xff>;
+
+			wifi@0 {
+				compatible = "pci17cb,1107";
+				reg = <0x40000 0x0 0x0 0x0 0x0>;
+
+				vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+				vddaon-supply = <&vreg_pmu_aon_0p59>;
+				vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+				vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+				vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+				vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+				vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+				vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+				vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+			};
+		};
+
+		pcie@3,0 {
+			reg = <0x21800 0x0 0x0 0x0 0x0>;
+			#address-cells = <3>;
+			#size-cells = <2>;
+			device_type = "pci";
+			ranges;
+			bus-range = <0x5 0xff>;
+		};
+	};
+};
+
+&pm8550_gpios {
+	volume_up_n: volume-up-n-state {
+		pins = "gpio6";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+
+	sdc2_card_det_n: sdc2-card-det-state {
+		pins = "gpio12";
+		function = "normal";
+		power-source = <1>;
+		bias-pull-up;
+		input-enable;
+	};
+};
+
+&pm8550_pwm {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	status = "okay";
+
+	led@1 {
+		reg = <1>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_STATUS;
+		function-enumerator = <0>;
+		linux,default-trigger = "none";
+		default-state = "off";
+	};
+
+	led@2 {
+		reg = <2>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_STATUS;
+		function-enumerator = <1>;
+		linux,default-trigger = "none";
+		default-state = "off";
+	};
+
+	led@3 {
+		reg = <3>;
+		color = <LED_COLOR_ID_GREEN>;
+		function = LED_FUNCTION_STATUS;
+		function-enumerator = <2>;
+		linux,default-trigger = "none";
+		default-state = "off";
+	};
+};
+
+&pm8550b_eusb2_repeater {
+	vdd18-supply = <&vreg_l15b_1p8>;
+	vdd3-supply = <&vreg_l5b_3p1>;
+};
+
+&pmk8550_gpios {
+	pmk8550_sleep_clk: sleep-clk-state {
+		pins = "gpio3";
+		function = "func1";
+		input-disable;
+		output-enable;
+		bias-disable;
+		power-source = <0>;
+	};
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+
+	status = "okay";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8550/adsp.mbn",
+			"qcom/sm8550/adsp_dtb.mbn";
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/sm8550/cdsp.mbn",
+			"qcom/sm8550/cdsp_dtb.mbn";
+	status = "okay";
+};
+
+&remoteproc_mpss {
+	firmware-name = "qcom/sm8550/modem.mbn",
+			"qcom/sm8550/modem_dtb.mbn";
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&sdc2_default>, <&sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep>, <&sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+
+	vmmc-supply = <&vreg_l9b_2p9>;
+	vqmmc-supply = <&vreg_l8b_1p8>;
+
+	no-sdio;
+	no-mmc;
+
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32764>;
+};
+
+&spi11 {
+	status = "okay";
+
+	can@0 {
+		compatible = "microchip,mcp2518fd";
+		reg = <0>;
+		interrupts-extended = <&tlmm 55 IRQ_TYPE_LEVEL_LOW>;
+		clocks = <&clk40m>;
+		spi-max-frequency = <10000000>;
+		vdd-supply = <&vreg_l14b_3p2>;
+		xceiver-supply = <&vreg_l14b_3p2>;
+	};
+};
+
+&swr0 {
+	status = "okay";
+
+	left_spkr: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+
+		reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	right_spkr: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+
+		reset-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
+
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&tlmm {
+	/* 32-35 for NFC secure element */
+	/* 36-39 for fingerprint sensor */
+	gpio-reserved-ranges = <32 8>;
+
+	lt9611_rst_pin: lt9611-rst-state {
+		pins = "gpio7";
+		function = "gpio";
+	};
+
+	upd_3p3_en: upd-3p3-en-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	lt9611_irq_pin: lt9611-irq-state {
+		pins = "gpio40";
+		function = "gpio";
+		bias-disable;
+	};
+
+	ntn1_en: ntn1-en-state {
+		pins = "gpio42";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tc9563_0_rst: tc9563-0-rst-state {
+		pins = "gpio64";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tc9563_1_rst: tc9563-1-rst-state {
+		pins = "gpio65";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	ntn0_en: ntn0-en-state {
+		pins = "gpio67";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wlan_en: wlan-en-state {
+		pins = "gpio80";
+		function = "gpio";
+		drive-strength = <8>;
+		bias-pull-down;
+	};
+
+	bt_default: bt-default-state {
+		pins = "gpio81";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	sw_ctrl_default: sw-ctrl-default-state {
+		pins = "gpio82";
+		function = "gpio";
+		bias-pull-down;
+	};
+
+	upd_1p05_en: upd-1p05-en-state {
+		pins = "gpio179";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	upd_ponrst: upd-ponrst-state {
+		pins = "gpio182";
+		function = "gpio";
+		drive-strength = <2>;
+		output-high;
+	};
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+	};
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+	vcc-supply = <&vreg_l17b_2p5>;
+	vcc-max-microamp = <1300000>;
+	vccq-supply = <&vreg_l1g_1p2>;
+	vccq-max-microamp = <1200000>;
+	vdd-hba-supply = <&vreg_l3g_1p2>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l1d_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_hsphy {
+	vdd-supply = <&vreg_l1e_0p88>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&pm8550b_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3f_0p88>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy_out {
+	remote-endpoint = <&redriver_phy_con_ss>;
+};
+
+&xo_board {
+	clock-frequency = <76800000>;
+};

-- 
2.34.1

Re: [PATCH v4 5/5] arm64: dts: qcom: qcs8550: add QCS8550 RB5Gen2 board support

[Dmitry Baryshkov]

On Mon, Apr 20, 2026 at 10:13:17AM +0100, Joe Sandom via B4 Relay wrote:
> From: Joe Sandom <jsandom@axon.com>
> 
> The RB5gen2 is an embedded development platform for the
> QCS8550, based on the Snapdragon 8 Gen 2 SoC (SM8550).
> 
> This change implements the main board, the vision mezzanine
> will be supported in a follow up patch.
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

Re: [PATCH v4 5/5] arm64: dts: qcom: qcs8550: add QCS8550 RB5Gen2 board support

[Konrad Dybcio]

On 4/20/26 11:13 AM, Joe Sandom via B4 Relay wrote:
> From: Joe Sandom <jsandom@axon.com>
> 
> The RB5gen2 is an embedded development platform for the
> QCS8550, based on the Snapdragon 8 Gen 2 SoC (SM8550).

[...]
> +	upd_ponrst: upd-ponrst-state {
> +		pins = "gpio182";
> +		function = "gpio";
> +		drive-strength = <2>;
> +		output-high;
> +	};

This should be made to mirror:

https://lore.kernel.org/linux-arm-msm/20260323-rb3gen2-upd-gl3590-v2-1-073514bf9ed5@oss.qualcomm.com/

Other than that:

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad