Re: [PATCH v2 2/4] PCI: dwc: Add ECAM support with iATU configuration

[Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>]

On 24.12.2024 3:10 PM, Krishna Chaitanya Chundru wrote:
> From: Krishna chaitanya chundru <quic_krichai@quicinc.com>
> 
> The current implementation requires iATU for every configuration
> space access which increases latency & cpu utilization.
> 
> Designware databook 5.20a, section 3.10.10.3 says about CFG Shift Feature,
> which shifts/maps the BDF (bits [31:16] of the third header DWORD, which
> would be matched against the Base and Limit addresses) of the incoming
> CfgRd0/CfgWr0 down to bits[27:12]of the translated address.
> 
> Configuring iATU in config shift feature enables ECAM feature to access the
> config space, which avoids iATU configuration for every config access.
> 
> Add "ctrl2" into struct dw_pcie_ob_atu_cfg  to enable config shift feature.
> 
> As DBI comes under config space, this avoids remapping of DBI space
> separately. Instead, it uses the mapped config space address returned from
> ECAM initialization. Change the order of dw_pcie_get_resources() execution
> to achieve this.
> 
> Enable the ECAM feature if the config space size is equal to size required
> to represent number of buses in the bus range property, add a function
> which checks this. The DWC glue drivers uses this function and decide to
> enable ECAM mode or not.
> 
> Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
> ---
>  drivers/pci/controller/dwc/Kconfig                |   1 +
>  drivers/pci/controller/dwc/pcie-designware-host.c | 136 +++++++++++++++++++---
>  drivers/pci/controller/dwc/pcie-designware.c      |   2 +-
>  drivers/pci/controller/dwc/pcie-designware.h      |  11 ++
>  4 files changed, 130 insertions(+), 20 deletions(-)
> 
> diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> index b6d6778b0698..73c3aed6b60a 100644
> --- a/drivers/pci/controller/dwc/Kconfig
> +++ b/drivers/pci/controller/dwc/Kconfig
> @@ -9,6 +9,7 @@ config PCIE_DW
>  config PCIE_DW_HOST
>  	bool
>  	select PCIE_DW
> +	select PCI_HOST_COMMON
>  
>  config PCIE_DW_EP
>  	bool
> diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
> index d2291c3ceb8b..4e07fefe12e1 100644
> --- a/drivers/pci/controller/dwc/pcie-designware-host.c
> +++ b/drivers/pci/controller/dwc/pcie-designware-host.c
> @@ -418,6 +418,61 @@ static void dw_pcie_host_request_msg_tlp_res(struct dw_pcie_rp *pp)
>  	}
>  }
>  
> +static int dw_pcie_config_ecam_iatu(struct dw_pcie_rp *pp)
> +{
> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> +	struct dw_pcie_ob_atu_cfg atu = {0};
> +	struct resource_entry *bus;
> +	int ret, bus_range_max;

resource_size_t for bus_range_max since you feed it the ouput of
resource_size()

> +
> +	bus = resource_list_first_type(&pp->bridge->windows, IORESOURCE_BUS);
> +
> +	/*
> +	 * Root bus under the root port doesn't require any iATU configuration
> +	 * as DBI space will represent Root bus configuration space.
> +	 * Immediate bus under Root Bus, needs type 0 iATU configuration and
> +	 * remaining buses need type 1 iATU configuration.
> +	 */
> +	atu.index = 0;
> +	atu.type = PCIE_ATU_TYPE_CFG0;
> +	atu.cpu_addr = pp->cfg0_base + SZ_1M;
> +	atu.size = SZ_1M;
> +	atu.ctrl2 = PCIE_ATU_CFG_SHIFT_MODE_ENABLE;
> +	ret = dw_pcie_prog_outbound_atu(pci, &atu);
> +	if (ret)
> +		return ret;
> +
> +	bus_range_max = resource_size(bus->res);
> +
> +	/* Configure remaining buses in type 1 iATU configuration */
> +	atu.index = 1;
> +	atu.type = PCIE_ATU_TYPE_CFG1;
> +	atu.cpu_addr = pp->cfg0_base + SZ_2M;
> +	atu.size = (SZ_1M * (bus_range_max - 2));

This explodes badly with:

bus-range = <0 0>;


> +	atu.ctrl2 = PCIE_ATU_CFG_SHIFT_MODE_ENABLE;
> +	return dw_pcie_prog_outbound_atu(pci, &atu);

A newline before the return statement would make it prettier

[...]

> +bool dw_pcie_ecam_supported(struct dw_pcie_rp *pp)
> +{
> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> +	struct platform_device *pdev = to_platform_device(pci->dev);
> +	struct resource *config_res, *bus_range;
> +	u64 bus_config_space_count;
> +
> +	bus_range = resource_list_first_type(&pp->bridge->windows, IORESOURCE_BUS)->res;
> +	if (!bus_range)
> +		return false;
> +
> +	config_res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "config");
> +	if (!config_res)
> +		return false;
> +
> +	bus_config_space_count = resource_size(config_res) >> PCIE_ECAM_BUS_SHIFT;
> +	if (resource_size(bus_range) > bus_config_space_count)
> +		return false;
> +
> +	return true;

return bus_config_space_count <= resource_size(bus_range);

Konrad