* [PATCH 2/3] ARM: dts: mxs: modify mx23/mx28 dts files to use pinctrl headers
[not found] <20130812072957.GB25061@S2101-09.ap.freescale.net>
2013-09-02 13:03 ` [PATCH v2 1/3] ARM: dts: mxs: add pinctrl header files Lothar Waßmann
2013-09-02 13:03 ` [PATCH " Lothar Waßmann
@ 2013-09-02 13:03 ` Lothar Waßmann
2013-09-02 13:03 ` [PATCH 3/3] ARM: dts: mxs: modify mx23/mx28 dts files to use padconfig defines Lothar Waßmann
3 siblings, 0 replies; 8+ messages in thread
From: Lothar Waßmann @ 2013-09-02 13:03 UTC (permalink / raw)
To: devicetree
Cc: Shawn Guo, Rob Herring, Stephen Warren, Lothar Waßmann,
Lauri Hintsala
Convert mx23/mx28 dts filed to use the pinctrl header files.
NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts
According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX
I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx23-evk.dts | 10 +-
arch/arm/boot/dts/imx23-olinuxino.dts | 6 +-
arch/arm/boot/dts/imx23-stmp378x_devb.dts | 6 +-
arch/arm/boot/dts/imx23.dtsi | 163 +++++++-------
arch/arm/boot/dts/imx28-apf28.dts | 2 +-
arch/arm/boot/dts/imx28-apf28dev.dts | 24 +-
arch/arm/boot/dts/imx28-apx4devkit.dts | 38 ++--
arch/arm/boot/dts/imx28-cfa10036.dts | 8 +-
arch/arm/boot/dts/imx28-cfa10037.dts | 6 +-
arch/arm/boot/dts/imx28-cfa10049.dts | 84 ++++----
arch/arm/boot/dts/imx28-cfa10055.dts | 56 +++---
arch/arm/boot/dts/imx28-cfa10056.dts | 20 +-
arch/arm/boot/dts/imx28-cfa10057.dts | 48 ++--
arch/arm/boot/dts/imx28-cfa10058.dts | 12 +-
arch/arm/boot/dts/imx28-evk.dts | 32 ++--
arch/arm/boot/dts/imx28-m28evk.dts | 16 +-
arch/arm/boot/dts/imx28-sps1.dts | 8 +-
arch/arm/boot/dts/imx28.dtsi | 337 +++++++++++++++--------------
18 files changed, 439 insertions(+), 437 deletions(-)
diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts
index 185c7c0..fdd8b27 100644
--- a/arch/arm/boot/dts/imx23-evk.dts
+++ b/arch/arm/boot/dts/imx23-evk.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx23.dtsi"
+#include "imx23.dtsi"
/ {
model = "Freescale i.MX23 Evaluation Kit";
@@ -45,10 +45,10 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1123 /* MX23_PAD_LCD_RESET__GPIO_1_18 */
- 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */
- 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */
- 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
+ MX23_PAD_LCD_RESET__GPIO_1_18
+ MX23_PAD_PWM3__GPIO_1_29
+ MX23_PAD_PWM4__GPIO_1_30
+ MX23_PAD_SSP1_DETECT__SSP1_DETECT
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts
index fc766ae..f575434 100644
--- a/arch/arm/boot/dts/imx23-olinuxino.dts
+++ b/arch/arm/boot/dts/imx23-olinuxino.dts
@@ -12,7 +12,7 @@
*/
/dts-v1/;
-/include/ "imx23.dtsi"
+#include "imx23.dtsi"
/ {
model = "i.MX23 Olinuxino Low Cost Board";
@@ -40,7 +40,7 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0113 /* MX23_PAD_GPMI_ALE__GPIO_0_17 */
+ MX23_PAD_GPMI_ALE__GPIO_0_17
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -50,7 +50,7 @@
led_pin_gpio2_1: led_gpio2_1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2013 /* MX23_PAD_SSP1_DETECT__GPIO_2_1 */
+ MX23_PAD_SSP1_DETECT__GPIO_2_1
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx23-stmp378x_devb.dts b/arch/arm/boot/dts/imx23-stmp378x_devb.dts
index 85c3864..2c8a9b0 100644
--- a/arch/arm/boot/dts/imx23-stmp378x_devb.dts
+++ b/arch/arm/boot/dts/imx23-stmp378x_devb.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx23.dtsi"
+#include "imx23.dtsi"
/ {
model = "Freescale STMP378x Development Board";
@@ -39,8 +39,8 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11d3 /* MX23_PAD_PWM3__GPIO_1_29 */
- 0x11e3 /* MX23_PAD_PWM4__GPIO_1_30 */
+ MX23_PAD_PWM3__GPIO_1_29
+ MX23_PAD_PWM4__GPIO_1_30
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi
index 28b5ce2..ff96e59 100644
--- a/arch/arm/boot/dts/imx23.dtsi
+++ b/arch/arm/boot/dts/imx23.dtsi
@@ -9,7 +9,8 @@
* http://www.gnu.org/copyleft/gpl.html
*/
-/include/ "skeleton.dtsi"
+#include "skeleton.dtsi"
+#include "imx23-pinfunc.h"
/ {
interrupt-parent = <&icoll>;
@@ -137,8 +138,8 @@
duart_pins_a: duart@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11a2 /* MX23_PAD_PWM0__DUART_RX */
- 0x11b2 /* MX23_PAD_PWM1__DUART_TX */
+ MX23_PAD_PWM0__DUART_RX
+ MX23_PAD_PWM1__DUART_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -148,10 +149,10 @@
auart0_pins_a: auart0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x01c0 /* MX23_PAD_AUART1_RX__AUART1_RX */
- 0x01d0 /* MX23_PAD_AUART1_TX__AUART1_TX */
- 0x01a0 /* MX23_PAD_AUART1_CTS__AUART1_CTS */
- 0x01b0 /* MX23_PAD_AUART1_RTS__AUART1_RTS */
+ MX23_PAD_AUART1_RX__AUART1_RX
+ MX23_PAD_AUART1_TX__AUART1_TX
+ MX23_PAD_AUART1_CTS__AUART1_CTS
+ MX23_PAD_AUART1_RTS__AUART1_RTS
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -161,8 +162,8 @@
auart0_2pins_a: auart0-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x01e2 /* MX23_PAD_I2C_SCL__AUART1_TX */
- 0x01f2 /* MX23_PAD_I2C_SDA__AUART1_RX */
+ MX23_PAD_I2C_SCL__AUART1_TX
+ MX23_PAD_I2C_SDA__AUART1_RX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -172,23 +173,23 @@
gpmi_pins_a: gpmi-nand@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0000 /* MX23_PAD_GPMI_D00__GPMI_D00 */
- 0x0010 /* MX23_PAD_GPMI_D01__GPMI_D01 */
- 0x0020 /* MX23_PAD_GPMI_D02__GPMI_D02 */
- 0x0030 /* MX23_PAD_GPMI_D03__GPMI_D03 */
- 0x0040 /* MX23_PAD_GPMI_D04__GPMI_D04 */
- 0x0050 /* MX23_PAD_GPMI_D05__GPMI_D05 */
- 0x0060 /* MX23_PAD_GPMI_D06__GPMI_D06 */
- 0x0070 /* MX23_PAD_GPMI_D07__GPMI_D07 */
- 0x0100 /* MX23_PAD_GPMI_CLE__GPMI_CLE */
- 0x0110 /* MX23_PAD_GPMI_ALE__GPMI_ALE */
- 0x0130 /* MX23_PAD_GPMI_RDY0__GPMI_RDY0 */
- 0x0140 /* MX23_PAD_GPMI_RDY1__GPMI_RDY1 */
- 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */
- 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */
- 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */
- 0x21b0 /* MX23_PAD_GPMI_CE1N__GPMI_CE1N */
- 0x21c0 /* MX23_PAD_GPMI_CE0N__GPMI_CE0N */
+ MX23_PAD_GPMI_D00__GPMI_D00
+ MX23_PAD_GPMI_D01__GPMI_D01
+ MX23_PAD_GPMI_D02__GPMI_D02
+ MX23_PAD_GPMI_D03__GPMI_D03
+ MX23_PAD_GPMI_D04__GPMI_D04
+ MX23_PAD_GPMI_D05__GPMI_D05
+ MX23_PAD_GPMI_D06__GPMI_D06
+ MX23_PAD_GPMI_D07__GPMI_D07
+ MX23_PAD_GPMI_CLE__GPMI_CLE
+ MX23_PAD_GPMI_ALE__GPMI_ALE
+ MX23_PAD_GPMI_RDY0__GPMI_RDY0
+ MX23_PAD_GPMI_RDY1__GPMI_RDY1
+ MX23_PAD_GPMI_WPN__GPMI_WPN
+ MX23_PAD_GPMI_WRN__GPMI_WRN
+ MX23_PAD_GPMI_RDN__GPMI_RDN
+ MX23_PAD_GPMI_CE1N__GPMI_CE1N
+ MX23_PAD_GPMI_CE0N__GPMI_CE0N
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -197,9 +198,9 @@
gpmi_pins_fixup: gpmi-pins-fixup {
fsl,pinmux-ids = <
- 0x0170 /* MX23_PAD_GPMI_WPN__GPMI_WPN */
- 0x0180 /* MX23_PAD_GPMI_WRN__GPMI_WRN */
- 0x0190 /* MX23_PAD_GPMI_RDN__GPMI_RDN */
+ MX23_PAD_GPMI_WPN__GPMI_WPN
+ MX23_PAD_GPMI_WRN__GPMI_WRN
+ MX23_PAD_GPMI_RDN__GPMI_RDN
>;
fsl,drive-strength = <2>;
};
@@ -207,12 +208,12 @@
mmc0_4bit_pins_a: mmc0-4bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */
- 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */
- 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */
- 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */
- 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */
- 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ MX23_PAD_SSP1_DATA0__SSP1_DATA0
+ MX23_PAD_SSP1_DATA1__SSP1_DATA1
+ MX23_PAD_SSP1_DATA2__SSP1_DATA2
+ MX23_PAD_SSP1_DATA3__SSP1_DATA3
+ MX23_PAD_SSP1_CMD__SSP1_CMD
+ MX23_PAD_SSP1_SCK__SSP1_SCK
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -222,17 +223,17 @@
mmc0_8bit_pins_a: mmc0-8bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2020 /* MX23_PAD_SSP1_DATA0__SSP1_DATA0 */
- 0x2030 /* MX23_PAD_SSP1_DATA1__SSP1_DATA1 */
- 0x2040 /* MX23_PAD_SSP1_DATA2__SSP1_DATA2 */
- 0x2050 /* MX23_PAD_SSP1_DATA3__SSP1_DATA3 */
- 0x0082 /* MX23_PAD_GPMI_D08__SSP1_DATA4 */
- 0x0092 /* MX23_PAD_GPMI_D09__SSP1_DATA5 */
- 0x00a2 /* MX23_PAD_GPMI_D10__SSP1_DATA6 */
- 0x00b2 /* MX23_PAD_GPMI_D11__SSP1_DATA7 */
- 0x2000 /* MX23_PAD_SSP1_CMD__SSP1_CMD */
- 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
- 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ MX23_PAD_SSP1_DATA0__SSP1_DATA0
+ MX23_PAD_SSP1_DATA1__SSP1_DATA1
+ MX23_PAD_SSP1_DATA2__SSP1_DATA2
+ MX23_PAD_SSP1_DATA3__SSP1_DATA3
+ MX23_PAD_GPMI_D08__SSP1_DATA4
+ MX23_PAD_GPMI_D09__SSP1_DATA5
+ MX23_PAD_GPMI_D10__SSP1_DATA6
+ MX23_PAD_GPMI_D11__SSP1_DATA7
+ MX23_PAD_SSP1_CMD__SSP1_CMD
+ MX23_PAD_SSP1_DETECT__SSP1_DETECT
+ MX23_PAD_SSP1_SCK__SSP1_SCK
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -241,8 +242,8 @@
mmc0_pins_fixup: mmc0-pins-fixup {
fsl,pinmux-ids = <
- 0x2010 /* MX23_PAD_SSP1_DETECT__SSP1_DETECT */
- 0x2060 /* MX23_PAD_SSP1_SCK__SSP1_SCK */
+ MX23_PAD_SSP1_DETECT__SSP1_DETECT
+ MX23_PAD_SSP1_SCK__SSP1_SCK
>;
fsl,pull-up = <0>;
};
@@ -250,7 +251,7 @@
pwm2_pins_a: pwm2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11c0 /* MX23_PAD_PWM2__PWM2 */
+ MX23_PAD_PWM2__PWM2
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -260,34 +261,34 @@
lcdif_24bit_pins_a: lcdif-24bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX23_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX23_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX23_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX23_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX23_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX23_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX23_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX23_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX23_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX23_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX23_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX23_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX23_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX23_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX23_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX23_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX23_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX23_PAD_LCD_D17__LCD_D17 */
- 0x0081 /* MX23_PAD_GPMI_D08__LCD_D18 */
- 0x0091 /* MX23_PAD_GPMI_D09__LCD_D19 */
- 0x00a1 /* MX23_PAD_GPMI_D10__LCD_D20 */
- 0x00b1 /* MX23_PAD_GPMI_D11__LCD_D21 */
- 0x00c1 /* MX23_PAD_GPMI_D12__LCD_D22 */
- 0x00d1 /* MX23_PAD_GPMI_D13__LCD_D23 */
- 0x1160 /* MX23_PAD_LCD_DOTCK__LCD_DOTCK */
- 0x1170 /* MX23_PAD_LCD_ENABLE__LCD_ENABLE */
- 0x1180 /* MX23_PAD_LCD_HSYNC__LCD_HSYNC */
- 0x1190 /* MX23_PAD_LCD_VSYNC__LCD_VSYNC */
+ MX23_PAD_LCD_D00__LCD_D00
+ MX23_PAD_LCD_D01__LCD_D01
+ MX23_PAD_LCD_D02__LCD_D02
+ MX23_PAD_LCD_D03__LCD_D03
+ MX23_PAD_LCD_D04__LCD_D04
+ MX23_PAD_LCD_D05__LCD_D05
+ MX23_PAD_LCD_D06__LCD_D06
+ MX23_PAD_LCD_D07__LCD_D07
+ MX23_PAD_LCD_D08__LCD_D08
+ MX23_PAD_LCD_D09__LCD_D09
+ MX23_PAD_LCD_D10__LCD_D10
+ MX23_PAD_LCD_D11__LCD_D11
+ MX23_PAD_LCD_D12__LCD_D12
+ MX23_PAD_LCD_D13__LCD_D13
+ MX23_PAD_LCD_D14__LCD_D14
+ MX23_PAD_LCD_D15__LCD_D15
+ MX23_PAD_LCD_D16__LCD_D16
+ MX23_PAD_LCD_D17__LCD_D17
+ MX23_PAD_GPMI_D08__LCD_D18
+ MX23_PAD_GPMI_D09__LCD_D19
+ MX23_PAD_GPMI_D10__LCD_D20
+ MX23_PAD_GPMI_D11__LCD_D21
+ MX23_PAD_GPMI_D12__LCD_D22
+ MX23_PAD_GPMI_D13__LCD_D23
+ MX23_PAD_LCD_DOTCK__LCD_DOTCK
+ MX23_PAD_LCD_ENABLE__LCD_ENABLE
+ MX23_PAD_LCD_HSYNC__LCD_HSYNC
+ MX23_PAD_LCD_VSYNC__LCD_VSYNC
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -297,10 +298,10 @@
spi2_pins_a: spi2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0182 /* MX23_PAD_GPMI_WRN__SSP2_SCK */
- 0x0142 /* MX23_PAD_GPMI_RDY1__SSP2_CMD */
- 0x0002 /* MX23_PAD_GPMI_D00__SSP2_DATA0 */
- 0x0032 /* MX23_PAD_GPMI_D03__SSP2_DATA3 */
+ MX23_PAD_GPMI_WRN__SSP2_SCK
+ MX23_PAD_GPMI_RDY1__SSP2_CMD
+ MX23_PAD_GPMI_D00__SSP2_DATA0
+ MX23_PAD_GPMI_D03__SSP2_DATA3
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-apf28.dts b/arch/arm/boot/dts/imx28-apf28.dts
index 7eb0758..7198fe3 100644
--- a/arch/arm/boot/dts/imx28-apf28.dts
+++ b/arch/arm/boot/dts/imx28-apf28.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Armadeus Systems APF28 module";
diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts
index b602494..7d923cc 100644
--- a/arch/arm/boot/dts/imx28-apf28dev.dts
+++ b/arch/arm/boot/dts/imx28-apf28dev.dts
@@ -10,7 +10,7 @@
*/
/* APF28Dev is a docking board for the APF28 SOM */
-/include/ "imx28-apf28.dts"
+#include "imx28-apf28.dts"
/ {
model = "Armadeus Systems APF28Dev docking/development board";
@@ -41,13 +41,13 @@
hog_pins_apf28dev: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1103 /* MX28_PAD_LCD_D16__GPIO_1_16 */
- 0x1113 /* MX28_PAD_LCD_D17__GPIO_1_17 */
- 0x1123 /* MX28_PAD_LCD_D18__GPIO_1_18 */
- 0x1133 /* MX28_PAD_LCD_D19__GPIO_1_19 */
- 0x1143 /* MX28_PAD_LCD_D20__GPIO_1_20 */
- 0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */
- 0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
+ MX28_PAD_LCD_D16__GPIO_1_16
+ MX28_PAD_LCD_D17__GPIO_1_17
+ MX28_PAD_LCD_D18__GPIO_1_18
+ MX28_PAD_LCD_D19__GPIO_1_19
+ MX28_PAD_LCD_D20__GPIO_1_20
+ MX28_PAD_LCD_D21__GPIO_1_21
+ MX28_PAD_LCD_D22__GPIO_1_22
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -57,10 +57,10 @@
lcdif_pins_apf28dev: lcdif-apf28dev@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts
index 0e7fed4..cb19dc1 100644
--- a/arch/arm/boot/dts/imx28-apx4devkit.dts
+++ b/arch/arm/boot/dts/imx28-apx4devkit.dts
@@ -1,5 +1,5 @@
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Bluegiga APX4 Development Kit";
@@ -40,13 +40,13 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */
- 0x0153 /* MX28_PAD_GPMI_RDY1__GPIO_0_21 */
- 0x2123 /* MX28_PAD_SSP2_MISO__GPIO_2_18 */
- 0x2131 /* MX28_PAD_SSP2_SS0__GPIO_2_19 */
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
- 0x4143 /* MX28_PAD_JTAG_RTCK__GPIO_4_20 */
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_RDY1__GPIO_0_21
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_JTAG_RTCK__GPIO_4_20
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -56,10 +56,10 @@
lcdif_pins_apx4: lcdif-apx4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -69,12 +69,12 @@
mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2041 /* MX28_PAD_SSP0_DATA4__SSP2_D0 */
- 0x2051 /* MX28_PAD_SSP0_DATA5__SSP2_D3 */
- 0x2061 /* MX28_PAD_SSP0_DATA6__SSP2_CMD */
- 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */
- 0x2141 /* MX28_PAD_SSP2_SS1__SSP2_D1 */
- 0x2151 /* MX28_PAD_SSP2_SS2__SSP2_D2 */
+ MX28_PAD_SSP0_DATA4__SSP2_D0
+ MX28_PAD_SSP0_DATA5__SSP2_D3
+ MX28_PAD_SSP0_DATA6__SSP2_CMD
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
+ MX28_PAD_SSP2_SS1__SSP2_D1
+ MX28_PAD_SSP2_SS2__SSP2_D2
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -83,7 +83,7 @@
mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4 {
fsl,pinmux-ids = <
- 0x2071 /* MX28_PAD_SSP0_DATA7__SSP2_SCK */
+ MX28_PAD_SSP0_DATA7__SSP2_SCK
>;
fsl,drive-strength = <2>;
fsl,pull-up = <0>;
diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts
index 1ec8c94..2474207 100644
--- a/arch/arm/boot/dts/imx28-cfa10036.dts
+++ b/arch/arm/boot/dts/imx28-cfa10036.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Crystalfontz CFA-10036 Board";
@@ -26,7 +26,7 @@
ssd1306_cfa10036: ssd1306-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2073 /* MX28_PAD_SSP0_D7__GPIO_2_7 */
+ MX28_PAD_SSP0_DATA7__GPIO_2_7
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -36,7 +36,7 @@
led_pins_cfa10036: leds-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3043 /* MX28_PAD_AUART1_RX__GPIO_3_4 */
+ MX28_PAD_AUART1_RX__GPIO_3_4
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -46,7 +46,7 @@
usb0_otg_cfa10036: otg-10036@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0142 /* MX28_PAD_GPMI_READY0__USB0_ID */
+ MX28_PAD_GPMI_RDY0__USB0_ID
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10037.dts b/arch/arm/boot/dts/imx28-cfa10037.dts
index 182b99f..42a9a99 100644
--- a/arch/arm/boot/dts/imx28-cfa10037.dts
+++ b/arch/arm/boot/dts/imx28-cfa10037.dts
@@ -13,7 +13,7 @@
* The CFA-10049 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10037 Board";
@@ -25,7 +25,7 @@
usb_pins_cfa10037: usb-10037@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -35,7 +35,7 @@
mac0_pins_cfa10037: mac0-10037@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
+ MX28_PAD_SSP2_SS2__GPIO_2_21
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 06e4cfa..9ee2566 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -13,7 +13,7 @@
* The CFA-10049 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10049 Board";
@@ -25,7 +25,7 @@
usb_pins_cfa10049: usb-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -35,8 +35,8 @@
i2cmux_pins_cfa10049: i2cmux-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1163 /* MX28_PAD_LCD_D22__GPIO_1_22 */
- 0x1173 /* MX28_PAD_LCD_D22__GPIO_1_23 */
+ MX28_PAD_LCD_D22__GPIO_1_22
+ MX28_PAD_LCD_D23__GPIO_1_23
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -46,7 +46,7 @@
mac0_pins_cfa10049: mac0-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2153 /* MX28_PAD_SSP2_D5__GPIO_2_21 */
+ MX28_PAD_SSP2_SS2__GPIO_2_21
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -56,7 +56,7 @@
pca_pins_cfa10049: pca-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2133 /* MX28_PAD_SSP2_D3__GPIO_2_19 */
+ MX28_PAD_SSP2_SS0__GPIO_2_19
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -66,8 +66,8 @@
rotary_pins_cfa10049: rotary-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3183 /* MX28_PAD_I2C0_SCL__GPIO_3_24 */
- 0x3193 /* MX28_PAD_I2C0_SDA__GPIO_3_25 */
+ MX28_PAD_I2C0_SCL__GPIO_3_24
+ MX28_PAD_I2C0_SDA__GPIO_3_25
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -77,7 +77,7 @@
rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31a3 /* MX28_PAD_SAIF_SDATA0__GPIO_3_26 */
+ MX28_PAD_SAIF1_SDATA0__GPIO_3_26
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -87,10 +87,10 @@
spi2_pins_cfa10049: spi2-cfa10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
- 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
- 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -100,11 +100,11 @@
spi3_pins_cfa10049: spi3-cfa10049@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0183 /* MX28_PAD_GPMI_RDN__GPIO_0_24 */
- 0x01c3 /* MX28_PAD_GPMI_RESETN__GPIO_0_28 */
- 0x0113 /* MX28_PAD_GPMI_CE1N__GPIO_0_17 */
- 0x01a3 /* MX28_PAD_GPMI_ALE__GPIO_0_26 */
- 0x01b3 /* MX28_PAD_GPMI_CLE__GPIO_0_27 */
+ MX28_PAD_GPMI_RDN__GPIO_0_24
+ MX28_PAD_GPMI_RESETN__GPIO_0_28
+ MX28_PAD_GPMI_CE1N__GPIO_0_17
+ MX28_PAD_GPMI_ALE__GPIO_0_26
+ MX28_PAD_GPMI_CLE__GPIO_0_27
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -114,24 +114,24 @@
lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -141,10 +141,10 @@
lcdif_pins_cfa10049: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -154,7 +154,7 @@
lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+ MX28_PAD_LCD_RESET__GPIO_3_30
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -164,7 +164,7 @@
w1_gpio_pins: w1-gpio@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1153 /* MX28_PAD_LCD_D21__GPIO_1_21 */
+ MX28_PAD_LCD_D21__GPIO_1_21
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
index 171bcbe..8b262a2 100644
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ b/arch/arm/boot/dts/imx28-cfa10055.dts
@@ -14,7 +14,7 @@
* The CFA-10055 is an expansion board for the CFA-10036 module and
* CFA-10037, thus we need to include the CFA-10037 DTS.
*/
-/include/ "imx28-cfa10037.dts"
+#include "imx28-cfa10037.dts"
/ {
model = "Crystalfontz CFA-10055 Board";
@@ -26,10 +26,10 @@
spi2_pins_cfa10055: spi2-cfa10055@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
- 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
- 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -39,24 +39,24 @@
lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -66,10 +66,10 @@
lcdif_pins_cfa10055: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -79,7 +79,7 @@
lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+ MX28_PAD_LCD_RESET__GPIO_3_30
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
index b45dd0e..f651998 100644
--- a/arch/arm/boot/dts/imx28-cfa10056.dts
+++ b/arch/arm/boot/dts/imx28-cfa10056.dts
@@ -13,7 +13,7 @@
* The CFA-10055 is an expansion board for the CFA-10036 module and
* CFA-10037, thus we need to include the CFA-10037 DTS.
*/
-/include/ "imx28-cfa10037.dts"
+#include "imx28-cfa10037.dts"
/ {
model = "Crystalfontz CFA-10056 Board";
@@ -25,10 +25,10 @@
spi2_pins_cfa10056: spi2-cfa10056@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2103 /* MX28_PAD_SSP2_SCK__GPIO_2_16 */
- 0x2113 /* MX28_PAD_SSP2_CMD__GPIO_2_17 */
- 0x2123 /* MX28_PAD_SSP2_D0__GPIO_2_18 */
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_SSP2_SCK__GPIO_2_16
+ MX28_PAD_SSP2_MOSI__GPIO_2_17
+ MX28_PAD_SSP2_MISO__GPIO_2_18
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -38,10 +38,10 @@
lcdif_pins_cfa10056: lcdif-10056@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -51,7 +51,7 @@
lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
+ MX28_PAD_LCD_RESET__GPIO_3_30
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts
index 0333c05..76430ca 100644
--- a/arch/arm/boot/dts/imx28-cfa10057.dts
+++ b/arch/arm/boot/dts/imx28-cfa10057.dts
@@ -14,7 +14,7 @@
* The CFA-10057 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10057 Board";
@@ -26,7 +26,7 @@
usb_pins_cfa10057: usb-10057@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -36,24 +36,24 @@
lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -63,10 +63,10 @@
lcdif_pins_cfa10057: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts
index 64c64c5..502be77 100644
--- a/arch/arm/boot/dts/imx28-cfa10058.dts
+++ b/arch/arm/boot/dts/imx28-cfa10058.dts
@@ -14,7 +14,7 @@
* The CFA-10058 is an expansion board for the CFA-10036 module, thus we
* need to include the CFA-10036 DTS.
*/
-/include/ "imx28-cfa10036.dts"
+#include "imx28-cfa10036.dts"
/ {
model = "Crystalfontz CFA-10058 Board";
@@ -26,7 +26,7 @@
usb_pins_cfa10058: usb-10058@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0073 /* MX28_PAD_GPMI_D7__GPIO_0_7 */
+ MX28_PAD_GPMI_D07__GPIO_0_7
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -36,10 +36,10 @@
lcdif_pins_cfa10058: lcdif-10058@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index 15715d9..dff2279 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "Freescale i.MX28 Evaluation Kit";
@@ -70,14 +70,14 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x20d3 /* MX28_PAD_SSP1_CMD__GPIO_2_13 */
- 0x20f3 /* MX28_PAD_SSP1_DATA3__GPIO_2_15 */
- 0x40d3 /* MX28_PAD_ENET0_RX_CLK__GPIO_4_13 */
- 0x20c3 /* MX28_PAD_SSP1_SCK__GPIO_2_12 */
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
- 0x31e3 /* MX28_PAD_LCD_RESET__GPIO_3_30 */
- 0x3083 /* MX28_PAD_AUART2_RX__GPIO_3_8 */
- 0x3093 /* MX28_PAD_AUART2_TX__GPIO_3_9 */
+ MX28_PAD_SSP1_CMD__GPIO_2_13
+ MX28_PAD_SSP1_DATA3__GPIO_2_15
+ MX28_PAD_ENET0_RX_CLK__GPIO_4_13
+ MX28_PAD_SSP1_SCK__GPIO_2_12
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_LCD_RESET__GPIO_3_30
+ MX28_PAD_AUART2_RX__GPIO_3_8
+ MX28_PAD_AUART2_TX__GPIO_3_9
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -87,7 +87,7 @@
led_pin_gpio3_5: led_gpio3_5@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3053 /* MX28_PAD_AUART1_TX__GPIO_3_5 */
+ MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -97,8 +97,8 @@
gpmi_pins_evk: gpmi-nand-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0110 /* MX28_PAD_GPMI_CE1N__GPMI_CE1N */
- 0x0150 /* MX28_PAD_GPMI_RDY1__GPMI_READY1 */
+ MX28_PAD_GPMI_CE1N__GPMI_CE1N
+ MX28_PAD_GPMI_RDY1__GPMI_READY1
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -108,10 +108,10 @@
lcdif_pins_evk: lcdif-evk@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts
index 0d322a2..9f3271d 100644
--- a/arch/arm/boot/dts/imx28-m28evk.dts
+++ b/arch/arm/boot/dts/imx28-m28evk.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "DENX M28EVK";
@@ -92,11 +92,11 @@
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31c3 /* MX28_PAD_PWM3__GPIO_3_28 */
- 0x30a3 /* MX28_PAD_AUART2_CTS__GPIO_3_10 */
- 0x30b3 /* MX28_PAD_AUART2_RTS__GPIO_3_11 */
- 0x30c3 /* MX28_PAD_AUART3_RX__GPIO_3_12 */
- 0x30d3 /* MX28_PAD_AUART3_TX__GPIO_3_13 */
+ MX28_PAD_PWM3__GPIO_3_28
+ MX28_PAD_AUART2_CTS__GPIO_3_10
+ MX28_PAD_AUART2_RTS__GPIO_3_11
+ MX28_PAD_AUART3_RX__GPIO_3_12
+ MX28_PAD_AUART3_TX__GPIO_3_13
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -106,8 +106,8 @@
lcdif_pins_m28: lcdif-m28@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11e0 /* MX28_PAD_LCD_DOTCLK__LCD_DOTCLK */
- 0x11f0 /* MX28_PAD_LCD_ENABLE__LCD_ENABLE */
+ MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
+ MX28_PAD_LCD_ENABLE__LCD_ENABLE
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts
index 6c6a544..4613522 100644
--- a/arch/arm/boot/dts/imx28-sps1.dts
+++ b/arch/arm/boot/dts/imx28-sps1.dts
@@ -10,7 +10,7 @@
*/
/dts-v1/;
-/include/ "imx28.dtsi"
+#include "imx28.dtsi"
/ {
model = "SchulerControl GmbH, SC SPS 1";
@@ -29,9 +29,9 @@
hog_pins_a: hog-gpios@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0003 /* MX28_PAD_GPMI_D00__GPIO_0_0 */
- 0x0033 /* MX28_PAD_GPMI_D03__GPIO_0_3 */
- 0x0063 /* MX28_PAD_GPMI_D06__GPIO_0_6 */
+ MX28_PAD_GPMI_D00__GPIO_0_0
+ MX28_PAD_GPMI_D03__GPIO_0_3
+ MX28_PAD_GPMI_D06__GPIO_0_6
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index 11e9840..14344c0 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -9,7 +9,8 @@
* http://www.gnu.org/copyleft/gpl.html
*/
-/include/ "skeleton.dtsi"
+#include "skeleton.dtsi"
+#include "imx28-pinfunc.h"
/ {
interrupt-parent = <&icoll>;
@@ -207,8 +208,8 @@
duart_pins_a: duart@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3102 /* MX28_PAD_PWM0__DUART_RX */
- 0x3112 /* MX28_PAD_PWM1__DUART_TX */
+ MX28_PAD_PWM0__DUART_RX
+ MX28_PAD_PWM1__DUART_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -218,8 +219,8 @@
duart_pins_b: duart@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */
- 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */
+ MX28_PAD_AUART0_CTS__DUART_RX
+ MX28_PAD_AUART0_RTS__DUART_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -229,10 +230,10 @@
duart_4pins_a: duart-4pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3022 /* MX28_PAD_AUART0_CTS__DUART_RX */
- 0x3032 /* MX28_PAD_AUART0_RTS__DUART_TX */
- 0x3002 /* MX28_PAD_AUART0_RX__DUART_CTS */
- 0x3012 /* MX28_PAD_AUART0_TX__DUART_RTS */
+ MX28_PAD_AUART0_CTS__DUART_RX
+ MX28_PAD_AUART0_RTS__DUART_TX
+ MX28_PAD_AUART0_RX__DUART_CTS
+ MX28_PAD_AUART0_TX__DUART_RTS
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -242,21 +243,21 @@
gpmi_pins_a: gpmi-nand@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0000 /* MX28_PAD_GPMI_D00__GPMI_D0 */
- 0x0010 /* MX28_PAD_GPMI_D01__GPMI_D1 */
- 0x0020 /* MX28_PAD_GPMI_D02__GPMI_D2 */
- 0x0030 /* MX28_PAD_GPMI_D03__GPMI_D3 */
- 0x0040 /* MX28_PAD_GPMI_D04__GPMI_D4 */
- 0x0050 /* MX28_PAD_GPMI_D05__GPMI_D5 */
- 0x0060 /* MX28_PAD_GPMI_D06__GPMI_D6 */
- 0x0070 /* MX28_PAD_GPMI_D07__GPMI_D7 */
- 0x0100 /* MX28_PAD_GPMI_CE0N__GPMI_CE0N */
- 0x0140 /* MX28_PAD_GPMI_RDY0__GPMI_READY0 */
- 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */
- 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */
- 0x01a0 /* MX28_PAD_GPMI_ALE__GPMI_ALE */
- 0x01b0 /* MX28_PAD_GPMI_CLE__GPMI_CLE */
- 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */
+ MX28_PAD_GPMI_D00__GPMI_D0
+ MX28_PAD_GPMI_D01__GPMI_D1
+ MX28_PAD_GPMI_D02__GPMI_D2
+ MX28_PAD_GPMI_D03__GPMI_D3
+ MX28_PAD_GPMI_D04__GPMI_D4
+ MX28_PAD_GPMI_D05__GPMI_D5
+ MX28_PAD_GPMI_D06__GPMI_D6
+ MX28_PAD_GPMI_D07__GPMI_D7
+ MX28_PAD_GPMI_CE0N__GPMI_CE0N
+ MX28_PAD_GPMI_RDY0__GPMI_READY0
+ MX28_PAD_GPMI_RDN__GPMI_RDN
+ MX28_PAD_GPMI_WRN__GPMI_WRN
+ MX28_PAD_GPMI_ALE__GPMI_ALE
+ MX28_PAD_GPMI_CLE__GPMI_CLE
+ MX28_PAD_GPMI_RESETN__GPMI_RESETN
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -265,9 +266,9 @@
gpmi_status_cfg: gpmi-status-cfg {
fsl,pinmux-ids = <
- 0x0180 /* MX28_PAD_GPMI_RDN__GPMI_RDN */
- 0x0190 /* MX28_PAD_GPMI_WRN__GPMI_WRN */
- 0x01c0 /* MX28_PAD_GPMI_RESETN__GPMI_RESETN */
+ MX28_PAD_GPMI_RDN__GPMI_RDN
+ MX28_PAD_GPMI_WRN__GPMI_WRN
+ MX28_PAD_GPMI_RESETN__GPMI_RESETN
>;
fsl,drive-strength = <2>;
};
@@ -275,10 +276,10 @@
auart0_pins_a: auart0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */
- 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */
- 0x3020 /* MX28_PAD_AUART0_CTS__AUART0_CTS */
- 0x3030 /* MX28_PAD_AUART0_RTS__AUART0_RTS */
+ MX28_PAD_AUART0_RX__AUART0_RX
+ MX28_PAD_AUART0_TX__AUART0_TX
+ MX28_PAD_AUART0_CTS__AUART0_CTS
+ MX28_PAD_AUART0_RTS__AUART0_RTS
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -288,8 +289,8 @@
auart0_2pins_a: auart0-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3000 /* MX28_PAD_AUART0_RX__AUART0_RX */
- 0x3010 /* MX28_PAD_AUART0_TX__AUART0_TX */
+ MX28_PAD_AUART0_RX__AUART0_RX
+ MX28_PAD_AUART0_TX__AUART0_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -299,10 +300,10 @@
auart1_pins_a: auart1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */
- 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */
- 0x3060 /* MX28_PAD_AUART1_CTS__AUART1_CTS */
- 0x3070 /* MX28_PAD_AUART1_RTS__AUART1_RTS */
+ MX28_PAD_AUART1_RX__AUART1_RX
+ MX28_PAD_AUART1_TX__AUART1_TX
+ MX28_PAD_AUART1_CTS__AUART1_CTS
+ MX28_PAD_AUART1_RTS__AUART1_RTS
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -312,8 +313,8 @@
auart1_2pins_a: auart1-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3040 /* MX28_PAD_AUART1_RX__AUART1_RX */
- 0x3050 /* MX28_PAD_AUART1_TX__AUART1_TX */
+ MX28_PAD_AUART1_RX__AUART1_RX
+ MX28_PAD_AUART1_TX__AUART1_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -323,8 +324,8 @@
auart2_2pins_a: auart2-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2101 /* MX28_PAD_SSP2_SCK__AUART2_RX */
- 0x2111 /* MX28_PAD_SSP2_MOSI__AUART2_TX */
+ MX28_PAD_SSP2_SCK__AUART2_RX
+ MX28_PAD_SSP2_MOSI__AUART2_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -334,8 +335,8 @@
auart2_2pins_b: auart2-2pins@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3080 /* MX28_PAD_AUART2_RX__AUART2_RX */
- 0x3090 /* MX28_PAD_AUART2_TX__AUART2_TX */
+ MX28_PAD_AUART2_RX__AUART2_RX
+ MX28_PAD_AUART2_TX__AUART2_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -345,10 +346,10 @@
auart3_pins_a: auart3@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */
- 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */
- 0x30e0 /* MX28_PAD_AUART3_CTS__AUART3_CTS */
- 0x30f0 /* MX28_PAD_AUART3_RTS__AUART3_RTS */
+ MX28_PAD_AUART3_RX__AUART3_RX
+ MX28_PAD_AUART3_TX__AUART3_TX
+ MX28_PAD_AUART3_CTS__AUART3_CTS
+ MX28_PAD_AUART3_RTS__AUART3_RTS
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -358,8 +359,8 @@
auart3_2pins_a: auart3-2pins@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2121 /* MX28_PAD_SSP2_MISO__AUART3_RX */
- 0x2131 /* MX28_PAD_SSP2_SS0__AUART3_TX */
+ MX28_PAD_SSP2_MISO__AUART3_RX
+ MX28_PAD_SSP2_SS0__AUART3_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -369,8 +370,8 @@
auart3_2pins_b: auart3-2pins@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x30c0 /* MX28_PAD_AUART3_RX__AUART3_RX */
- 0x30d0 /* MX28_PAD_AUART3_TX__AUART3_TX */
+ MX28_PAD_AUART3_RX__AUART3_RX
+ MX28_PAD_AUART3_TX__AUART3_TX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -380,8 +381,8 @@
auart4_2pins_a: auart4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2181 /* MX28_PAD_SSP3_SCK__AUART4_TX */
- 0x2191 /* MX28_PAD_SSP3_MOSI__AUART4_RX */
+ MX28_PAD_SSP3_SCK__AUART4_TX
+ MX28_PAD_SSP3_MOSI__AUART4_RX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -391,15 +392,15 @@
mac0_pins_a: mac0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x4000 /* MX28_PAD_ENET0_MDC__ENET0_MDC */
- 0x4010 /* MX28_PAD_ENET0_MDIO__ENET0_MDIO */
- 0x4020 /* MX28_PAD_ENET0_RX_EN__ENET0_RX_EN */
- 0x4030 /* MX28_PAD_ENET0_RXD0__ENET0_RXD0 */
- 0x4040 /* MX28_PAD_ENET0_RXD1__ENET0_RXD1 */
- 0x4060 /* MX28_PAD_ENET0_TX_EN__ENET0_TX_EN */
- 0x4070 /* MX28_PAD_ENET0_TXD0__ENET0_TXD0 */
- 0x4080 /* MX28_PAD_ENET0_TXD1__ENET0_TXD1 */
- 0x4100 /* MX28_PAD_ENET_CLK__CLKCTRL_ENET */
+ MX28_PAD_ENET0_MDC__ENET0_MDC
+ MX28_PAD_ENET0_MDIO__ENET0_MDIO
+ MX28_PAD_ENET0_RX_EN__ENET0_RX_EN
+ MX28_PAD_ENET0_RXD0__ENET0_RXD0
+ MX28_PAD_ENET0_RXD1__ENET0_RXD1
+ MX28_PAD_ENET0_TX_EN__ENET0_TX_EN
+ MX28_PAD_ENET0_TXD0__ENET0_TXD0
+ MX28_PAD_ENET0_TXD1__ENET0_TXD1
+ MX28_PAD_ENET_CLK__CLKCTRL_ENET
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -409,12 +410,12 @@
mac1_pins_a: mac1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x40f1 /* MX28_PAD_ENET0_CRS__ENET1_RX_EN */
- 0x4091 /* MX28_PAD_ENET0_RXD2__ENET1_RXD0 */
- 0x40a1 /* MX28_PAD_ENET0_RXD3__ENET1_RXD1 */
- 0x40e1 /* MX28_PAD_ENET0_COL__ENET1_TX_EN */
- 0x40b1 /* MX28_PAD_ENET0_TXD2__ENET1_TXD0 */
- 0x40c1 /* MX28_PAD_ENET0_TXD3__ENET1_TXD1 */
+ MX28_PAD_ENET0_CRS__ENET1_RX_EN
+ MX28_PAD_ENET0_RXD2__ENET1_RXD0
+ MX28_PAD_ENET0_RXD3__ENET1_RXD1
+ MX28_PAD_ENET0_COL__ENET1_TX_EN
+ MX28_PAD_ENET0_TXD2__ENET1_TXD0
+ MX28_PAD_ENET0_TXD3__ENET1_TXD1
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -424,17 +425,17 @@
mmc0_8bit_pins_a: mmc0-8bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */
- 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */
- 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */
- 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */
- 0x2040 /* MX28_PAD_SSP0_DATA4__SSP0_D4 */
- 0x2050 /* MX28_PAD_SSP0_DATA5__SSP0_D5 */
- 0x2060 /* MX28_PAD_SSP0_DATA6__SSP0_D6 */
- 0x2070 /* MX28_PAD_SSP0_DATA7__SSP0_D7 */
- 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */
- 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
- 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ MX28_PAD_SSP0_DATA0__SSP0_D0
+ MX28_PAD_SSP0_DATA1__SSP0_D1
+ MX28_PAD_SSP0_DATA2__SSP0_D2
+ MX28_PAD_SSP0_DATA3__SSP0_D3
+ MX28_PAD_SSP0_DATA4__SSP0_D4
+ MX28_PAD_SSP0_DATA5__SSP0_D5
+ MX28_PAD_SSP0_DATA6__SSP0_D6
+ MX28_PAD_SSP0_DATA7__SSP0_D7
+ MX28_PAD_SSP0_CMD__SSP0_CMD
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
+ MX28_PAD_SSP0_SCK__SSP0_SCK
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -444,13 +445,13 @@
mmc0_4bit_pins_a: mmc0-4bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2000 /* MX28_PAD_SSP0_DATA0__SSP0_D0 */
- 0x2010 /* MX28_PAD_SSP0_DATA1__SSP0_D1 */
- 0x2020 /* MX28_PAD_SSP0_DATA2__SSP0_D2 */
- 0x2030 /* MX28_PAD_SSP0_DATA3__SSP0_D3 */
- 0x2080 /* MX28_PAD_SSP0_CMD__SSP0_CMD */
- 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
- 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ MX28_PAD_SSP0_DATA0__SSP0_D0
+ MX28_PAD_SSP0_DATA1__SSP0_D1
+ MX28_PAD_SSP0_DATA2__SSP0_D2
+ MX28_PAD_SSP0_DATA3__SSP0_D3
+ MX28_PAD_SSP0_CMD__SSP0_CMD
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
+ MX28_PAD_SSP0_SCK__SSP0_SCK
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -459,14 +460,14 @@
mmc0_cd_cfg: mmc0-cd-cfg {
fsl,pinmux-ids = <
- 0x2090 /* MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT */
+ MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
>;
fsl,pull-up = <0>;
};
mmc0_sck_cfg: mmc0-sck-cfg {
fsl,pinmux-ids = <
- 0x20a0 /* MX28_PAD_SSP0_SCK__SSP0_SCK */
+ MX28_PAD_SSP0_SCK__SSP0_SCK
>;
fsl,drive-strength = <2>;
fsl,pull-up = <0>;
@@ -475,8 +476,8 @@
i2c0_pins_a: i2c0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3180 /* MX28_PAD_I2C0_SCL__I2C0_SCL */
- 0x3190 /* MX28_PAD_I2C0_SDA__I2C0_SDA */
+ MX28_PAD_I2C0_SCL__I2C0_SCL
+ MX28_PAD_I2C0_SDA__I2C0_SDA
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -486,8 +487,8 @@
i2c0_pins_b: i2c0@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3001 /* MX28_PAD_AUART0_RX__I2C0_SCL */
- 0x3011 /* MX28_PAD_AUART0_TX__I2C0_SDA */
+ MX28_PAD_AUART0_RX__I2C0_SCL
+ MX28_PAD_AUART0_TX__I2C0_SDA
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -497,8 +498,8 @@
i2c1_pins_a: i2c1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3101 /* MX28_PAD_PWM0__I2C1_SCL */
- 0x3111 /* MX28_PAD_PWM1__I2C1_SDA */
+ MX28_PAD_PWM0__I2C1_SCL
+ MX28_PAD_PWM1__I2C1_SDA
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -508,10 +509,10 @@
saif0_pins_a: saif0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3140 /* MX28_PAD_SAIF0_MCLK__SAIF0_MCLK */
- 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */
- 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */
- 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */
+ MX28_PAD_SAIF0_MCLK__SAIF0_MCLK
+ MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK
+ MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK
+ MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -521,9 +522,9 @@
saif0_pins_b: saif0@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3150 /* MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK */
- 0x3160 /* MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK */
- 0x3170 /* MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0 */
+ MX28_PAD_SAIF0_LRCLK__SAIF0_LRCLK
+ MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK
+ MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -545,7 +546,7 @@
saif1_pins_a: saif1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31a0 /* MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0 */
+ MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -555,7 +556,7 @@
pwm0_pins_a: pwm0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3100 /* MX28_PAD_PWM0__PWM_0 */
+ MX28_PAD_PWM0__PWM_0
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -565,7 +566,7 @@
pwm2_pins_a: pwm2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3120 /* MX28_PAD_PWM2__PWM_2 */
+ MX28_PAD_PWM2__PWM_2
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -575,7 +576,7 @@
pwm3_pins_a: pwm3@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31c0 /* MX28_PAD_PWM3__PWM_3 */
+ MX28_PAD_PWM3__PWM_3
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -585,7 +586,7 @@
pwm3_pins_b: pwm3@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3141 /* MX28_PAD_SAIF0_MCLK__PWM3 */
+ MX28_PAD_SAIF0_MCLK__PWM_3
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -595,7 +596,7 @@
pwm4_pins_a: pwm4@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x31d0 /* MX28_PAD_PWM4__PWM_4 */
+ MX28_PAD_PWM4__PWM_4
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -605,30 +606,30 @@
lcdif_24bit_pins_a: lcdif-24bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
- 0x1100 /* MX28_PAD_LCD_D16__LCD_D16 */
- 0x1110 /* MX28_PAD_LCD_D17__LCD_D17 */
- 0x1120 /* MX28_PAD_LCD_D18__LCD_D18 */
- 0x1130 /* MX28_PAD_LCD_D19__LCD_D19 */
- 0x1140 /* MX28_PAD_LCD_D20__LCD_D20 */
- 0x1150 /* MX28_PAD_LCD_D21__LCD_D21 */
- 0x1160 /* MX28_PAD_LCD_D22__LCD_D22 */
- 0x1170 /* MX28_PAD_LCD_D23__LCD_D23 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
+ MX28_PAD_LCD_D16__LCD_D16
+ MX28_PAD_LCD_D17__LCD_D17
+ MX28_PAD_LCD_D18__LCD_D18
+ MX28_PAD_LCD_D19__LCD_D19
+ MX28_PAD_LCD_D20__LCD_D20
+ MX28_PAD_LCD_D21__LCD_D21
+ MX28_PAD_LCD_D22__LCD_D22
+ MX28_PAD_LCD_D23__LCD_D23
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -638,22 +639,22 @@
lcdif_16bit_pins_a: lcdif-16bit@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x1000 /* MX28_PAD_LCD_D00__LCD_D0 */
- 0x1010 /* MX28_PAD_LCD_D01__LCD_D1 */
- 0x1020 /* MX28_PAD_LCD_D02__LCD_D2 */
- 0x1030 /* MX28_PAD_LCD_D03__LCD_D3 */
- 0x1040 /* MX28_PAD_LCD_D04__LCD_D4 */
- 0x1050 /* MX28_PAD_LCD_D05__LCD_D5 */
- 0x1060 /* MX28_PAD_LCD_D06__LCD_D6 */
- 0x1070 /* MX28_PAD_LCD_D07__LCD_D7 */
- 0x1080 /* MX28_PAD_LCD_D08__LCD_D8 */
- 0x1090 /* MX28_PAD_LCD_D09__LCD_D9 */
- 0x10a0 /* MX28_PAD_LCD_D10__LCD_D10 */
- 0x10b0 /* MX28_PAD_LCD_D11__LCD_D11 */
- 0x10c0 /* MX28_PAD_LCD_D12__LCD_D12 */
- 0x10d0 /* MX28_PAD_LCD_D13__LCD_D13 */
- 0x10e0 /* MX28_PAD_LCD_D14__LCD_D14 */
- 0x10f0 /* MX28_PAD_LCD_D15__LCD_D15 */
+ MX28_PAD_LCD_D00__LCD_D0
+ MX28_PAD_LCD_D01__LCD_D1
+ MX28_PAD_LCD_D02__LCD_D2
+ MX28_PAD_LCD_D03__LCD_D3
+ MX28_PAD_LCD_D04__LCD_D4
+ MX28_PAD_LCD_D05__LCD_D5
+ MX28_PAD_LCD_D06__LCD_D6
+ MX28_PAD_LCD_D07__LCD_D7
+ MX28_PAD_LCD_D08__LCD_D8
+ MX28_PAD_LCD_D09__LCD_D9
+ MX28_PAD_LCD_D10__LCD_D10
+ MX28_PAD_LCD_D11__LCD_D11
+ MX28_PAD_LCD_D12__LCD_D12
+ MX28_PAD_LCD_D13__LCD_D13
+ MX28_PAD_LCD_D14__LCD_D14
+ MX28_PAD_LCD_D15__LCD_D15
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -663,10 +664,10 @@
lcdif_sync_pins_a: lcdif-sync@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x11a1 /* MX28_PAD_LCD_RS__LCD_DOTCLK */
- 0x11b1 /* MX28_PAD_LCD_CS__LCD_ENABLE */
- 0x1181 /* MX28_PAD_LCD_RD_E__LCD_VSYNC */
- 0x1191 /* MX28_PAD_LCD_WR_RWN__LCD_HSYNC */
+ MX28_PAD_LCD_RS__LCD_DOTCLK
+ MX28_PAD_LCD_CS__LCD_ENABLE
+ MX28_PAD_LCD_RD_E__LCD_VSYNC
+ MX28_PAD_LCD_WR_RWN__LCD_HSYNC
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -689,8 +690,8 @@
can0_pins_a: can0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0161 /* MX28_PAD_GPMI_RDY2__CAN0_TX */
- 0x0171 /* MX28_PAD_GPMI_RDY3__CAN0_RX */
+ MX28_PAD_GPMI_RDY2__CAN0_TX
+ MX28_PAD_GPMI_RDY3__CAN0_RX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -700,8 +701,8 @@
can1_pins_a: can1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x0121 /* MX28_PAD_GPMI_CE2N__CAN1_TX */
- 0x0131 /* MX28_PAD_GPMI_CE3N__CAN1_RX */
+ MX28_PAD_GPMI_CE2N__CAN1_TX
+ MX28_PAD_GPMI_CE3N__CAN1_RX
>;
fsl,drive-strength = <0>;
fsl,voltage = <1>;
@@ -711,10 +712,10 @@
spi2_pins_a: spi2@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2100 /* MX28_PAD_SSP2_SCK__SSP2_SCK */
- 0x2110 /* MX28_PAD_SSP2_MOSI__SSP2_CMD */
- 0x2120 /* MX28_PAD_SSP2_MISO__SSP2_D0 */
- 0x2130 /* MX28_PAD_SSP2_SS0__SSP2_D3 */
+ MX28_PAD_SSP2_SCK__SSP2_SCK
+ MX28_PAD_SSP2_MOSI__SSP2_CMD
+ MX28_PAD_SSP2_MISO__SSP2_D0
+ MX28_PAD_SSP2_SS0__SSP2_D3
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -724,12 +725,12 @@
spi3_pins_a: spi3@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x3082 /* MX28_PAD_AUART2_RX__SSP3_D4 */
- 0x3092 /* MX28_PAD_AUART2_TX__SSP3_D5 */
- 0x2180 /* MX28_PAD_SSP3_SCK__SSP3_SCK */
- 0x2190 /* MX28_PAD_SSP3_MOSI__SSP3_CMD */
- 0x21A0 /* MX28_PAD_SSP3_MISO__SSP3_D0 */
- 0x21B0 /* MX28_PAD_SSP3_SS0__SSP3_D3 */
+ MX28_PAD_AUART2_RX__SSP3_D4
+ MX28_PAD_AUART2_TX__SSP3_D5
+ MX28_PAD_SSP3_SCK__SSP3_SCK
+ MX28_PAD_SSP3_MOSI__SSP3_CMD
+ MX28_PAD_SSP3_MISO__SSP3_D0
+ MX28_PAD_SSP3_SS0__SSP3_D3
>;
fsl,drive-strength = <1>;
fsl,voltage = <1>;
@@ -739,7 +740,7 @@
usbphy0_pins_a: usbphy0@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2152 /* MX28_PAD_SSP2_SS2__USB0_OVERCURRENT */
+ MX28_PAD_SSP2_SS2__USB0_OVERCURRENT
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -749,7 +750,7 @@
usbphy0_pins_b: usbphy0@1 {
reg = <1>;
fsl,pinmux-ids = <
- 0x3061 /* MX28_PAD_AUART1_CTS__USB0_OVERCURRENT */
+ MX28_PAD_AUART1_CTS__USB0_OVERCURRENT
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
@@ -759,7 +760,7 @@
usbphy1_pins_a: usbphy1@0 {
reg = <0>;
fsl,pinmux-ids = <
- 0x2142 /* MX28_PAD_SSP2_SS1__USB1_OVERCURRENT */
+ MX28_PAD_SSP2_SS1__USB1_OVERCURRENT
>;
fsl,drive-strength = <2>;
fsl,voltage = <1>;
--
1.7.2.5
^ permalink raw reply related [flat|nested] 8+ messages in thread* [PATCH 3/3] ARM: dts: mxs: modify mx23/mx28 dts files to use padconfig defines
[not found] <20130812072957.GB25061@S2101-09.ap.freescale.net>
` (2 preceding siblings ...)
2013-09-02 13:03 ` [PATCH 2/3] ARM: dts: mxs: modify mx23/mx28 dts files to use pinctrl headers Lothar Waßmann
@ 2013-09-02 13:03 ` Lothar Waßmann
3 siblings, 0 replies; 8+ messages in thread
From: Lothar Waßmann @ 2013-09-02 13:03 UTC (permalink / raw)
To: devicetree; +Cc: Shawn Guo, Rob Herring, Stephen Warren, Lothar Waßmann
Convert mx23/mx28 dts files to use the padconfig defintions from
mxs-pinfunc.h.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
---
arch/arm/boot/dts/imx23-evk.dts | 6 +-
arch/arm/boot/dts/imx23-olinuxino.dts | 12 +-
arch/arm/boot/dts/imx23-stmp378x_devb.dts | 6 +-
arch/arm/boot/dts/imx23.dtsi | 58 ++++----
arch/arm/boot/dts/imx28-apf28dev.dts | 12 +-
arch/arm/boot/dts/imx28-apx4devkit.dts | 22 ++--
arch/arm/boot/dts/imx28-cfa10036.dts | 18 +-
arch/arm/boot/dts/imx28-cfa10037.dts | 12 +-
arch/arm/boot/dts/imx28-cfa10049.dts | 72 +++++-----
arch/arm/boot/dts/imx28-cfa10055.dts | 24 ++--
arch/arm/boot/dts/imx28-cfa10056.dts | 18 +-
arch/arm/boot/dts/imx28-cfa10057.dts | 18 +-
arch/arm/boot/dts/imx28-cfa10058.dts | 12 +-
arch/arm/boot/dts/imx28-evk.dts | 24 ++--
arch/arm/boot/dts/imx28-m28evk.dts | 12 +-
arch/arm/boot/dts/imx28-sps1.dts | 6 +-
arch/arm/boot/dts/imx28.dtsi | 242 ++++++++++++++--------------
17 files changed, 287 insertions(+), 287 deletions(-)
diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts
index fdd8b27..1f026ad 100644
--- a/arch/arm/boot/dts/imx23-evk.dts
+++ b/arch/arm/boot/dts/imx23-evk.dts
@@ -50,9 +50,9 @@
MX23_PAD_PWM4__GPIO_1_30
MX23_PAD_SSP1_DETECT__SSP1_DETECT
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts
index f575434..526bfdb 100644
--- a/arch/arm/boot/dts/imx23-olinuxino.dts
+++ b/arch/arm/boot/dts/imx23-olinuxino.dts
@@ -42,9 +42,9 @@
fsl,pinmux-ids = <
MX23_PAD_GPMI_ALE__GPIO_0_17
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pin_gpio2_1: led_gpio2_1@0 {
@@ -52,9 +52,9 @@
fsl,pinmux-ids = <
MX23_PAD_SSP1_DETECT__GPIO_2_1
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx23-stmp378x_devb.dts b/arch/arm/boot/dts/imx23-stmp378x_devb.dts
index 2c8a9b0..cb64e2b 100644
--- a/arch/arm/boot/dts/imx23-stmp378x_devb.dts
+++ b/arch/arm/boot/dts/imx23-stmp378x_devb.dts
@@ -42,9 +42,9 @@
MX23_PAD_PWM3__GPIO_1_29
MX23_PAD_PWM4__GPIO_1_30
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
};
diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi
index ff96e59..87faa6e 100644
--- a/arch/arm/boot/dts/imx23.dtsi
+++ b/arch/arm/boot/dts/imx23.dtsi
@@ -141,9 +141,9 @@
MX23_PAD_PWM0__DUART_RX
MX23_PAD_PWM1__DUART_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart0_pins_a: auart0@0 {
@@ -154,9 +154,9 @@
MX23_PAD_AUART1_CTS__AUART1_CTS
MX23_PAD_AUART1_RTS__AUART1_RTS
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart0_2pins_a: auart0-2pins@0 {
@@ -165,9 +165,9 @@
MX23_PAD_I2C_SCL__AUART1_TX
MX23_PAD_I2C_SDA__AUART1_RX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
gpmi_pins_a: gpmi-nand@0 {
@@ -191,9 +191,9 @@
MX23_PAD_GPMI_CE1N__GPMI_CE1N
MX23_PAD_GPMI_CE0N__GPMI_CE0N
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
gpmi_pins_fixup: gpmi-pins-fixup {
@@ -202,7 +202,7 @@
MX23_PAD_GPMI_WRN__GPMI_WRN
MX23_PAD_GPMI_RDN__GPMI_RDN
>;
- fsl,drive-strength = <2>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
};
mmc0_4bit_pins_a: mmc0-4bit@0 {
@@ -215,9 +215,9 @@
MX23_PAD_SSP1_CMD__SSP1_CMD
MX23_PAD_SSP1_SCK__SSP1_SCK
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc0_8bit_pins_a: mmc0-8bit@0 {
@@ -235,9 +235,9 @@
MX23_PAD_SSP1_DETECT__SSP1_DETECT
MX23_PAD_SSP1_SCK__SSP1_SCK
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc0_pins_fixup: mmc0-pins-fixup {
@@ -245,7 +245,7 @@
MX23_PAD_SSP1_DETECT__SSP1_DETECT
MX23_PAD_SSP1_SCK__SSP1_SCK
>;
- fsl,pull-up = <0>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pwm2_pins_a: pwm2@0 {
@@ -253,9 +253,9 @@
fsl,pinmux-ids = <
MX23_PAD_PWM2__PWM2
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_24bit_pins_a: lcdif-24bit@0 {
@@ -290,9 +290,9 @@
MX23_PAD_LCD_HSYNC__LCD_HSYNC
MX23_PAD_LCD_VSYNC__LCD_VSYNC
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
spi2_pins_a: spi2@0 {
@@ -303,9 +303,9 @@
MX23_PAD_GPMI_D00__SSP2_DATA0
MX23_PAD_GPMI_D03__SSP2_DATA3
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts
index 7d923cc..e2efd8d 100644
--- a/arch/arm/boot/dts/imx28-apf28dev.dts
+++ b/arch/arm/boot/dts/imx28-apf28dev.dts
@@ -49,9 +49,9 @@
MX28_PAD_LCD_D21__GPIO_1_21
MX28_PAD_LCD_D22__GPIO_1_22
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_apf28dev: lcdif-apf28dev@0 {
@@ -62,9 +62,9 @@
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts
index cb19dc1..6f254ca 100644
--- a/arch/arm/boot/dts/imx28-apx4devkit.dts
+++ b/arch/arm/boot/dts/imx28-apx4devkit.dts
@@ -48,9 +48,9 @@
MX28_PAD_LCD_RESET__GPIO_3_30
MX28_PAD_JTAG_RTCK__GPIO_4_20
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_apx4: lcdif-apx4@0 {
@@ -61,9 +61,9 @@
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
@@ -76,17 +76,17 @@
MX28_PAD_SSP2_SS1__SSP2_D1
MX28_PAD_SSP2_SS2__SSP2_D2
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4 {
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__SSP2_SCK
>;
- fsl,drive-strength = <2>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts
index 2474207..cabb617 100644
--- a/arch/arm/boot/dts/imx28-cfa10036.dts
+++ b/arch/arm/boot/dts/imx28-cfa10036.dts
@@ -28,9 +28,9 @@
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__GPIO_2_7
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins_cfa10036: leds-10036@0 {
@@ -38,9 +38,9 @@
fsl,pinmux-ids = <
MX28_PAD_AUART1_RX__GPIO_3_4
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
usb0_otg_cfa10036: otg-10036@0 {
@@ -48,9 +48,9 @@
fsl,pinmux-ids = <
MX28_PAD_GPMI_RDY0__USB0_ID
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10037.dts b/arch/arm/boot/dts/imx28-cfa10037.dts
index 42a9a99..f93e9a7 100644
--- a/arch/arm/boot/dts/imx28-cfa10037.dts
+++ b/arch/arm/boot/dts/imx28-cfa10037.dts
@@ -27,9 +27,9 @@
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_pins_cfa10037: mac0-10037@0 {
@@ -37,9 +37,9 @@
fsl,pinmux-ids = <
MX28_PAD_SSP2_SS2__GPIO_2_21
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts
index 9ee2566..7087b4b 100644
--- a/arch/arm/boot/dts/imx28-cfa10049.dts
+++ b/arch/arm/boot/dts/imx28-cfa10049.dts
@@ -27,9 +27,9 @@
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
i2cmux_pins_cfa10049: i2cmux-10049@0 {
@@ -38,9 +38,9 @@
MX28_PAD_LCD_D22__GPIO_1_22
MX28_PAD_LCD_D23__GPIO_1_23
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_pins_cfa10049: mac0-10049@0 {
@@ -48,9 +48,9 @@
fsl,pinmux-ids = <
MX28_PAD_SSP2_SS2__GPIO_2_21
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pca_pins_cfa10049: pca-10049@0 {
@@ -58,9 +58,9 @@
fsl,pinmux-ids = <
MX28_PAD_SSP2_SS0__GPIO_2_19
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
rotary_pins_cfa10049: rotary-10049@0 {
@@ -69,9 +69,9 @@
MX28_PAD_I2C0_SCL__GPIO_3_24
MX28_PAD_I2C0_SDA__GPIO_3_25
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
rotary_btn_pins_cfa10049: rotary-btn-10049@0 {
@@ -79,9 +79,9 @@
fsl,pinmux-ids = <
MX28_PAD_SAIF1_SDATA0__GPIO_3_26
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
spi2_pins_cfa10049: spi2-cfa10049@0 {
@@ -92,9 +92,9 @@
MX28_PAD_SSP2_MISO__GPIO_2_18
MX28_PAD_AUART1_TX__GPIO_3_5
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
spi3_pins_cfa10049: spi3-cfa10049@0 {
@@ -106,9 +106,9 @@
MX28_PAD_GPMI_ALE__GPIO_0_26
MX28_PAD_GPMI_CLE__GPIO_0_27
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
lcdif_18bit_pins_cfa10049: lcdif-18bit@0 {
@@ -133,9 +133,9 @@
MX28_PAD_LCD_D16__LCD_D16
MX28_PAD_LCD_D17__LCD_D17
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10049: lcdif-evk@0 {
@@ -146,9 +146,9 @@
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10049_pullup: lcdif-10049-pullup@0 {
@@ -156,9 +156,9 @@
fsl,pinmux-ids = <
MX28_PAD_LCD_RESET__GPIO_3_30
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
w1_gpio_pins: w1-gpio@0 {
@@ -166,9 +166,9 @@
fsl,pinmux-ids = <
MX28_PAD_LCD_D21__GPIO_1_21
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>; /* 0 will enable the keeper */
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>; /* 0 will enable the keeper */
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10055.dts b/arch/arm/boot/dts/imx28-cfa10055.dts
index 8b262a2..c3900e7 100644
--- a/arch/arm/boot/dts/imx28-cfa10055.dts
+++ b/arch/arm/boot/dts/imx28-cfa10055.dts
@@ -31,9 +31,9 @@
MX28_PAD_SSP2_MISO__GPIO_2_18
MX28_PAD_AUART1_TX__GPIO_3_5
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
lcdif_18bit_pins_cfa10055: lcdif-18bit@0 {
@@ -58,9 +58,9 @@
MX28_PAD_LCD_D16__LCD_D16
MX28_PAD_LCD_D17__LCD_D17
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10055: lcdif-evk@0 {
@@ -71,9 +71,9 @@
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10055_pullup: lcdif-10055-pullup@0 {
@@ -81,9 +81,9 @@
fsl,pinmux-ids = <
MX28_PAD_LCD_RESET__GPIO_3_30
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10056.dts b/arch/arm/boot/dts/imx28-cfa10056.dts
index f651998..cef959a 100644
--- a/arch/arm/boot/dts/imx28-cfa10056.dts
+++ b/arch/arm/boot/dts/imx28-cfa10056.dts
@@ -30,9 +30,9 @@
MX28_PAD_SSP2_MISO__GPIO_2_18
MX28_PAD_AUART1_TX__GPIO_3_5
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
lcdif_pins_cfa10056: lcdif-10056@0 {
@@ -43,9 +43,9 @@
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10056_pullup: lcdif-10056-pullup@0 {
@@ -53,9 +53,9 @@
fsl,pinmux-ids = <
MX28_PAD_LCD_RESET__GPIO_3_30
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts
index 76430ca..3c13128 100644
--- a/arch/arm/boot/dts/imx28-cfa10057.dts
+++ b/arch/arm/boot/dts/imx28-cfa10057.dts
@@ -28,9 +28,9 @@
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_18bit_pins_cfa10057: lcdif-18bit@0 {
@@ -55,9 +55,9 @@
MX28_PAD_LCD_D16__LCD_D16
MX28_PAD_LCD_D17__LCD_D17
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10057: lcdif-evk@0 {
@@ -68,9 +68,9 @@
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts
index 502be77..2469d34 100644
--- a/arch/arm/boot/dts/imx28-cfa10058.dts
+++ b/arch/arm/boot/dts/imx28-cfa10058.dts
@@ -28,9 +28,9 @@
fsl,pinmux-ids = <
MX28_PAD_GPMI_D07__GPIO_0_7
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_cfa10058: lcdif-10058@0 {
@@ -41,9 +41,9 @@
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index dff2279..468b07f 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -79,9 +79,9 @@
MX28_PAD_AUART2_RX__GPIO_3_8
MX28_PAD_AUART2_TX__GPIO_3_9
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pin_gpio3_5: led_gpio3_5@0 {
@@ -89,9 +89,9 @@
fsl,pinmux-ids = <
MX28_PAD_AUART1_TX__GPIO_3_5
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
gpmi_pins_evk: gpmi-nand-evk@0 {
@@ -100,9 +100,9 @@
MX28_PAD_GPMI_CE1N__GPMI_CE1N
MX28_PAD_GPMI_RDY1__GPMI_READY1
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_evk: lcdif-evk@0 {
@@ -113,9 +113,9 @@
MX28_PAD_LCD_RS__LCD_DOTCLK
MX28_PAD_LCD_CS__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts
index 9f3271d..8e2477f 100644
--- a/arch/arm/boot/dts/imx28-m28evk.dts
+++ b/arch/arm/boot/dts/imx28-m28evk.dts
@@ -98,9 +98,9 @@
MX28_PAD_AUART3_RX__GPIO_3_12
MX28_PAD_AUART3_TX__GPIO_3_13
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_pins_m28: lcdif-m28@0 {
@@ -109,9 +109,9 @@
MX28_PAD_LCD_DOTCLK__LCD_DOTCLK
MX28_PAD_LCD_ENABLE__LCD_ENABLE
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts
index 4613522..4870f07 100644
--- a/arch/arm/boot/dts/imx28-sps1.dts
+++ b/arch/arm/boot/dts/imx28-sps1.dts
@@ -33,9 +33,9 @@
MX28_PAD_GPMI_D03__GPIO_0_3
MX28_PAD_GPMI_D06__GPIO_0_6
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi
index 14344c0..901ab54 100644
--- a/arch/arm/boot/dts/imx28.dtsi
+++ b/arch/arm/boot/dts/imx28.dtsi
@@ -211,9 +211,9 @@
MX28_PAD_PWM0__DUART_RX
MX28_PAD_PWM1__DUART_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
duart_pins_b: duart@1 {
@@ -222,9 +222,9 @@
MX28_PAD_AUART0_CTS__DUART_RX
MX28_PAD_AUART0_RTS__DUART_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
duart_4pins_a: duart-4pins@0 {
@@ -235,9 +235,9 @@
MX28_PAD_AUART0_RX__DUART_CTS
MX28_PAD_AUART0_TX__DUART_RTS
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
gpmi_pins_a: gpmi-nand@0 {
@@ -259,9 +259,9 @@
MX28_PAD_GPMI_CLE__GPMI_CLE
MX28_PAD_GPMI_RESETN__GPMI_RESETN
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
gpmi_status_cfg: gpmi-status-cfg {
@@ -270,7 +270,7 @@
MX28_PAD_GPMI_WRN__GPMI_WRN
MX28_PAD_GPMI_RESETN__GPMI_RESETN
>;
- fsl,drive-strength = <2>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
};
auart0_pins_a: auart0@0 {
@@ -281,9 +281,9 @@
MX28_PAD_AUART0_CTS__AUART0_CTS
MX28_PAD_AUART0_RTS__AUART0_RTS
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart0_2pins_a: auart0-2pins@0 {
@@ -292,9 +292,9 @@
MX28_PAD_AUART0_RX__AUART0_RX
MX28_PAD_AUART0_TX__AUART0_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart1_pins_a: auart1@0 {
@@ -305,9 +305,9 @@
MX28_PAD_AUART1_CTS__AUART1_CTS
MX28_PAD_AUART1_RTS__AUART1_RTS
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart1_2pins_a: auart1-2pins@0 {
@@ -316,9 +316,9 @@
MX28_PAD_AUART1_RX__AUART1_RX
MX28_PAD_AUART1_TX__AUART1_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart2_2pins_a: auart2-2pins@0 {
@@ -327,9 +327,9 @@
MX28_PAD_SSP2_SCK__AUART2_RX
MX28_PAD_SSP2_MOSI__AUART2_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart2_2pins_b: auart2-2pins@1 {
@@ -338,9 +338,9 @@
MX28_PAD_AUART2_RX__AUART2_RX
MX28_PAD_AUART2_TX__AUART2_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart3_pins_a: auart3@0 {
@@ -351,9 +351,9 @@
MX28_PAD_AUART3_CTS__AUART3_CTS
MX28_PAD_AUART3_RTS__AUART3_RTS
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart3_2pins_a: auart3-2pins@0 {
@@ -362,9 +362,9 @@
MX28_PAD_SSP2_MISO__AUART3_RX
MX28_PAD_SSP2_SS0__AUART3_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart3_2pins_b: auart3-2pins@1 {
@@ -373,9 +373,9 @@
MX28_PAD_AUART3_RX__AUART3_RX
MX28_PAD_AUART3_TX__AUART3_TX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
auart4_2pins_a: auart4@0 {
@@ -384,9 +384,9 @@
MX28_PAD_SSP3_SCK__AUART4_TX
MX28_PAD_SSP3_MOSI__AUART4_RX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_pins_a: mac0@0 {
@@ -402,9 +402,9 @@
MX28_PAD_ENET0_TXD1__ENET0_TXD1
MX28_PAD_ENET_CLK__CLKCTRL_ENET
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mac1_pins_a: mac1@0 {
@@ -417,9 +417,9 @@
MX28_PAD_ENET0_TXD2__ENET1_TXD0
MX28_PAD_ENET0_TXD3__ENET1_TXD1
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc0_8bit_pins_a: mmc0-8bit@0 {
@@ -437,9 +437,9 @@
MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
MX28_PAD_SSP0_SCK__SSP0_SCK
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc0_4bit_pins_a: mmc0-4bit@0 {
@@ -453,24 +453,24 @@
MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
MX28_PAD_SSP0_SCK__SSP0_SCK
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
mmc0_cd_cfg: mmc0-cd-cfg {
fsl,pinmux-ids = <
MX28_PAD_SSP0_DETECT__SSP0_CARD_DETECT
>;
- fsl,pull-up = <0>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
mmc0_sck_cfg: mmc0-sck-cfg {
fsl,pinmux-ids = <
MX28_PAD_SSP0_SCK__SSP0_SCK
>;
- fsl,drive-strength = <2>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
i2c0_pins_a: i2c0@0 {
@@ -479,9 +479,9 @@
MX28_PAD_I2C0_SCL__I2C0_SCL
MX28_PAD_I2C0_SDA__I2C0_SDA
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
i2c0_pins_b: i2c0@1 {
@@ -490,9 +490,9 @@
MX28_PAD_AUART0_RX__I2C0_SCL
MX28_PAD_AUART0_TX__I2C0_SDA
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
i2c1_pins_a: i2c1@0 {
@@ -501,9 +501,9 @@
MX28_PAD_PWM0__I2C1_SCL
MX28_PAD_PWM1__I2C1_SDA
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
saif0_pins_a: saif0@0 {
@@ -514,9 +514,9 @@
MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK
MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
saif0_pins_b: saif0@1 {
@@ -526,9 +526,9 @@
MX28_PAD_SAIF0_BITCLK__SAIF0_BITCLK
MX28_PAD_SAIF0_SDATA0__SAIF0_SDATA0
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
saif0_pins_b: saif0@1 {
@@ -548,9 +548,9 @@
fsl,pinmux-ids = <
MX28_PAD_SAIF1_SDATA0__SAIF1_SDATA0
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
pwm0_pins_a: pwm0@0 {
@@ -558,9 +558,9 @@
fsl,pinmux-ids = <
MX28_PAD_PWM0__PWM_0
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pwm2_pins_a: pwm2@0 {
@@ -568,9 +568,9 @@
fsl,pinmux-ids = <
MX28_PAD_PWM2__PWM_2
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pwm3_pins_a: pwm3@0 {
@@ -578,9 +578,9 @@
fsl,pinmux-ids = <
MX28_PAD_PWM3__PWM_3
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pwm3_pins_b: pwm3@1 {
@@ -588,9 +588,9 @@
fsl,pinmux-ids = <
MX28_PAD_SAIF0_MCLK__PWM_3
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
pwm4_pins_a: pwm4@0 {
@@ -598,9 +598,9 @@
fsl,pinmux-ids = <
MX28_PAD_PWM4__PWM_4
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_24bit_pins_a: lcdif-24bit@0 {
@@ -631,9 +631,9 @@
MX28_PAD_LCD_D22__LCD_D22
MX28_PAD_LCD_D23__LCD_D23
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_16bit_pins_a: lcdif-16bit@0 {
@@ -656,9 +656,9 @@
MX28_PAD_LCD_D14__LCD_D14
MX28_PAD_LCD_D15__LCD_D15
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_sync_pins_a: lcdif-sync@0 {
@@ -669,9 +669,9 @@
MX28_PAD_LCD_RD_E__LCD_VSYNC
MX28_PAD_LCD_WR_RWN__LCD_HSYNC
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
lcdif_sync_pins_a: lcdif-sync@0 {
@@ -693,9 +693,9 @@
MX28_PAD_GPMI_RDY2__CAN0_TX
MX28_PAD_GPMI_RDY3__CAN0_RX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
can1_pins_a: can1@0 {
@@ -704,9 +704,9 @@
MX28_PAD_GPMI_CE2N__CAN1_TX
MX28_PAD_GPMI_CE3N__CAN1_RX
>;
- fsl,drive-strength = <0>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_4mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
spi2_pins_a: spi2@0 {
@@ -717,9 +717,9 @@
MX28_PAD_SSP2_MISO__SSP2_D0
MX28_PAD_SSP2_SS0__SSP2_D3
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <1>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_ENABLE>;
};
spi3_pins_a: spi3@0 {
@@ -732,9 +732,9 @@
MX28_PAD_SSP3_MISO__SSP3_D0
MX28_PAD_SSP3_SS0__SSP3_D3
>;
- fsl,drive-strength = <1>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_8mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
usbphy0_pins_a: usbphy0@0 {
@@ -742,9 +742,9 @@
fsl,pinmux-ids = <
MX28_PAD_SSP2_SS2__USB0_OVERCURRENT
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
usbphy0_pins_b: usbphy0@1 {
@@ -752,9 +752,9 @@
fsl,pinmux-ids = <
MX28_PAD_AUART1_CTS__USB0_OVERCURRENT
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
usbphy1_pins_a: usbphy1@0 {
@@ -762,9 +762,9 @@
fsl,pinmux-ids = <
MX28_PAD_SSP2_SS1__USB1_OVERCURRENT
>;
- fsl,drive-strength = <2>;
- fsl,voltage = <1>;
- fsl,pull-up = <0>;
+ fsl,drive-strength = <MXS_DRIVE_12mA>;
+ fsl,voltage = <MXS_VOLTAGE_HIGH>;
+ fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
--
1.7.2.5
^ permalink raw reply related [flat|nested] 8+ messages in thread