[PATCH v3 0/4] arm64: dts: qcom: Add IMDT QCS8550 SBC

[PATCH v3 0/4] arm64: dts: qcom: Add IMDT QCS8550 SBC

[William Bright]

This patch series adds DT support for the IMD Technologies Ltd (IMDT)
QCS8550 SBC and corresponding SoM. The SBC DTS supports the following
hardware on the SBC:
- Gigabit Ethernet (using a Microchip LAN7430 behind the on-board PCIe
  switch on PCIE1)
- USB3 as gadget mode only (No DP alt-mode and flip detection support)
- SD card (SDHC2)
- Regulators
- M.2 Key-E (PCIE0) The SoM DTSI supports the following hardware:
- PM8550 PMICs (similar to the SM8550-HDK)
- QCS8550 and UFS

The IMDT QCS8550 SBC hardware is capable of the following but support is
not included in this patch series:
- USB3 flip detection
- 8 MIPI CSI2 cameras are supported using 8 IAS connectors
- MIPI DSI Displays via a DSI/I2C connector
- Microphone input
- Speaker output
- Fan control
- RS232
- M.2 Key-B (also on PCIE1, selected by toggling the on-board PCIe
  switch away from the LAN7430 upstream port)
- Wi-Fi and Bluetooth via SDHC4/UART14 using an NXP-IW416 (SDHC4 patch
  [1] is awaiting review)

The DTS files were written using the SM8550-HDK as an initial starting
point with patches ported from downstream [2].

Claude Opus 4.7 was used for formatting and reviewing the device trees
against other QCS/SM8550 boards.

Patch 1 adds the IMDT vendor prefix
Patch 2 adds DT bindings for the SoM and SBC
Patch 3 adds the SoM DTSI
Patch 4 adds the SBC DTS

[1] https://lore.kernel.org/all/20260427-sm8550-sdhc4-support-v2-1-a4241f43ecd5@imd-tec.com
[2] https://github.com/imd-tec/meta-imdt-qcom/tree/kirkstone/patches/msm-kernel-devicetree/files

Signed-off-by: William Bright <william.bright@imd-tec.com>
---
Changes in v3:
- Dropped backlight node since it's unused. 
- Dropped regulators which are dead (no usage or not gpio controllable
  whilst also not strictly required by a DT node). 
- Dropped SBC modem remoteproc entry since the modem is fused off on the
  qcs8550.
- Reformatted commit bodies and DTS comments.
- Replaced open-drain properties with bias-disable due to open-drain not
  being supported by the tlmm.
- Dropped tlmm entries which are unused.
- Dropped disabling of LPASS codecs as it was unnecessary.
- Dropped bluetooth usage on uart14 and removed references to uart14
  since it became unused.
- Patch 2 renamed to "dt-bindings: arm: qcom: Add IMDT QCS8550 SBC/SoM"
- Patch 2 commit body shortened as it had information already found
  within the patch 3 body.
- Link to v2: https://patch.msgid.link/20260505-imdt-qcs8550-sbc-rfc-v2-0-b4767d0dd421@imd-tec.com

Changes in v2:
- Patch 1 relocated to be above qcs8550-aim300-aiot instead of below
- Split the SoM and SBC DT changes into two patches, with patch
  3 adding the SoM DTSI and patch 4 adding the SBC DTS.
- Dropped the SDHC4 node in patch 4 to focus on the core
  SoM and SBC device trees. 
  This allows the primary hardware support to progress through 
  review while waiting for feedback for [1].
- Link to v1: https://patch.msgid.link/20260430-imdt-qcs8550-sbc-rfc-v1-0-4d2b6675eaa3@imd-tec.com

To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Bjorn Andersson <andersson@kernel.org>
To: Konrad Dybcio <konradybcio@kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-msm@vger.kernel.org

---
William Bright (4):
      dt-bindings: vendor-prefixes: Add IMDT
      dt-bindings: arm: qcom: Document IMDT QCS8550 SBC/SoM
      arm64: dts: qcom: Add IMDT QCS8550 SoM
      arm64: dts: qcom: Add IMDT QCS8550 SBC

 Documentation/devicetree/bindings/arm/qcom.yaml    |   7 +
 .../devicetree/bindings/vendor-prefixes.yaml       |   2 +
 arch/arm64/boot/dts/qcom/Makefile                  |   1 +
 arch/arm64/boot/dts/qcom/qcs8550-imdt-sbc.dts      | 392 +++++++++++++++++++++
 arch/arm64/boot/dts/qcom/qcs8550-imdt-som.dtsi     | 319 +++++++++++++++++
 5 files changed, 721 insertions(+)
---
base-commit: 95b3f1f1b54d79bada9cf47420034cfe23df978f
change-id: 20260430-imdt-qcs8550-sbc-rfc-4e7cbfbcadd8

Best regards,
--  
William Bright <william.bright@imd-tec.com>

[PATCH v3 1/4] dt-bindings: vendor-prefixes: Add IMDT

[William Bright]

Add IMDT (IMD Technologies Ltd) to the vendor prefixes list.

Signed-off-by: William Bright <william.bright@imd-tec.com>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index ee7fd3cfe203..2db12a1cb6e1 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -769,6 +769,8 @@ patternProperties:
     description: ILI Technology Corporation (ILITEK)
   "^imagis,.*":
     description: Imagis Technologies Co., Ltd.
+  "^imdt,.*":
+    description: IMD Technologies Ltd.
   "^img,.*":
     description: Imagination Technologies Ltd.
   "^imi,.*":

-- 
2.43.0

[PATCH v3 2/4] dt-bindings: arm: qcom: Document IMDT QCS8550 SBC/SoM

[William Bright]

Document the IMDT QCS8550 SBC which consists of an IMDT QCS8550 SoM
soldered onto an IMDT QCS8550 carrier board.

Signed-off-by: William Bright <william.bright@imd-tec.com>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index cc29b06621a9..97735d31f1cf 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1073,6 +1073,13 @@ properties:
               - sony,pdx234
           - const: qcom,sm8550
 
+      - items:
+          - enum:
+              - imdt,qcs8550-sbc
+          - const: imdt,qcs8550-som
+          - const: qcom,qcs8550
+          - const: qcom,sm8550
+
       - items:
           - enum:
               - qcom,qcs8550-aim300-aiot

-- 
2.43.0

[PATCH v3 3/4] arm64: dts: qcom: Add IMDT QCS8550 SoM

[William Bright]

The IMDT QCS8550 SoM is a System-on-Module from IMD Technologies Ltd
built around the Qualcomm QCS8550 SoC. It is intended to be soldered
onto a carrier board that supplies VPH_PWR and exposes the off-module
peripherals.

Add qcs8550-imdt-som.dtsi describing the SoM's PMICs (PM8550, PM8550VE,
PM8550VS, PMK8550) and the apps_rsc PMIC outputs. Compared to other
SM8550/QCS8550 boards, this SoM excludes the PM8550B charger PMIC.

Assisted-by: Claude:claude-opus-4.7
Signed-off-by: William Bright <william.bright@imd-tec.com>
---
 arch/arm64/boot/dts/qcom/qcs8550-imdt-som.dtsi | 319 +++++++++++++++++++++++++
 1 file changed, 319 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/qcs8550-imdt-som.dtsi b/arch/arm64/boot/dts/qcom/qcs8550-imdt-som.dtsi
new file mode 100644
index 000000000000..816cbd254dea
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-imdt-som.dtsi
@@ -0,0 +1,319 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2026 IMD Technologies Ltd
+ */
+
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qcs8550.dtsi"
+#include "pm8550.dtsi"
+#define PMK8550VE_SID 5
+#include "pm8550ve.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob1>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l11-supply = <&vreg_s4g_1p25>;
+		vdd-l12-supply = <&vreg_s6g_1p86>;
+		vdd-l15-supply = <&vreg_s6g_1p86>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		/*
+		 * PMIC outputs whose testpoints lack capacitors are
+		 * omitted to prevent accidental use:
+		 *	L1B_1P8, L4B_1P8, L6B_1P8, L7B_1P8, L8B_1P8,
+		 *	L13B_3P0, L14B_3P2.
+		 * Other outputs are unused.
+		 */
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3296000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2720000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p1: ldo5 {
+			regulator-name = "vreg_l5b_3p1";
+			regulator-min-microvolt = <3104000>;
+			regulator-max-microvolt = <3104000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s4g_1p25>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+
+		vreg_l3c_0p9: ldo3 {
+			regulator-name = "vreg_l3c_0p9";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+
+		vreg_l1d_0p88: ldo1 {
+			regulator-name = "vreg_l1d_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		/* ldo2 supplies SM8550 VDD_LPI_MX */
+	};
+
+	regulators-3 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+
+		vreg_s4e_0p95: smps4 {
+			regulator-name = "vreg_s4e_0p95";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <984000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5e_1p08: smps5 {
+			regulator-name = "vreg_s5e_1p08";
+			regulator-min-microvolt = <1080000>;
+			regulator-max-microvolt = <1120000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1e_0p88: ldo1 {
+			regulator-name = "vreg_l1e_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2e_0p9: ldo2 {
+			regulator-name = "vreg_l2e_0p9";
+			regulator-min-microvolt = <904000>;
+			regulator-max-microvolt = <970000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s4e_0p95>;
+		vdd-l2-supply = <&vreg_s4e_0p95>;
+		vdd-l3-supply = <&vreg_s4e_0p95>;
+
+		vreg_s4f_0p5: smps4 {
+			regulator-name = "vreg_s4f_0p5";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <700000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1f_0p9: ldo1 {
+			regulator-name = "vreg_l1f_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_0p88: ldo2 {
+			regulator-name = "vreg_l2f_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_0p88: ldo3 {
+			regulator-name = "vreg_l3f_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-5 {
+		compatible = "qcom,pm8550vs-rpmh-regulators";
+		qcom,pmic-id = "g";
+
+		vdd-l1-supply = <&vreg_s4g_1p25>;
+		vdd-l2-supply = <&vreg_s4g_1p25>;
+		vdd-l3-supply = <&vreg_s4g_1p25>;
+
+		vreg_s1g_1p25: smps1 {
+			regulator-name = "vreg_s1g_1p25";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2g_0p85: smps2 {
+			regulator-name = "vreg_s2g_0p85";
+			regulator-min-microvolt = <800000>;
+			regulator-max-microvolt = <1000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s3g_0p8: smps3 {
+			regulator-name = "vreg_s3g_0p8";
+			regulator-min-microvolt = <300000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s4g_1p25: smps4 {
+			regulator-name = "vreg_s4g_1p25";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1352000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s5g_0p85: smps5 {
+			regulator-name = "vreg_s5g_0p85";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1004000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s6g_1p86: smps6 {
+			regulator-name = "vreg_s6g_1p86";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1g_1p2: ldo1 {
+			regulator-name = "vreg_l1g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3g_1p2: ldo3 {
+			regulator-name = "vreg_l3g_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-allow-set-load;
+			regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+						   RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&pm8550vs_c {
+	status = "okay";
+};
+
+&pm8550vs_d {
+	status = "okay";
+};
+
+&pm8550vs_d_gpios {
+	status = "okay";
+};
+
+&pm8550vs_e {
+	status = "okay";
+};
+
+&pm8550vs_g {
+	status = "okay";
+};
+
+&sleep_clk {
+	clock-frequency = <32764>;
+};
+
+&xo_board {
+	clock-frequency = <76800000>;
+};

-- 
2.43.0

[PATCH v3 4/4] arm64: dts: qcom: Add IMDT QCS8550 SBC

[William Bright]

The IMDT QCS8550 SBC is a two-board design from IMD Technologies Ltd
built around the Qualcomm QCS8550 SoC. An IMDT QCS8550 SoM is soldered
onto the IMDT QCS8550 carrier board that supplies VPH_PWR and exposes
the off-module peripherals.

With this DTS, the board can boot to shell with a UFS rootfs with
debugging through uart7. USB and ethernet also are fully functional.

Features enabled are:
- On-board regulators
- uSD
- UART
- UFS
- PCIe0
- PCIe1
- USB (gadget only)
- Ethernet via LAN7430 (PCIe1)
- ADSP, CDSP

Assisted-by: Claude:claude-opus-4.7
Signed-off-by: William Bright <william.bright@imd-tec.com>
---
 arch/arm64/boot/dts/qcom/Makefile             |   1 +
 arch/arm64/boot/dts/qcom/qcs8550-imdt-sbc.dts | 392 ++++++++++++++++++++++++++
 2 files changed, 393 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 88c5c0c1cb8e..d38fb3c43c13 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -181,6 +181,7 @@ qcs8300-ride-el2-dtbs := qcs8300-ride.dtb monaco-el2.dtbo
 
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8300-ride-el2.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-aim300-aiot.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-imdt-sbc.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride-r3.dtb
 
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-imdt-sbc.dts b/arch/arm64/boot/dts/qcom/qcs8550-imdt-sbc.dts
new file mode 100644
index 000000000000..e8afe683c962
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-imdt-sbc.dts
@@ -0,0 +1,392 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2026 IMD Technologies Ltd
+ */
+
+/dts-v1/;
+
+#include "qcs8550-imdt-som.dtsi"
+
+/ {
+	model = "IMDT QCS8550 SBC";
+	compatible = "imdt,qcs8550-sbc", "imdt,qcs8550-som",
+		     "qcom,qcs8550", "qcom,sm8550";
+	chassis-type = "embedded";
+
+	aliases {
+		serial0 = &uart7;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	/* Enables 5V_PER, 3V3_PER and 1V8_PER rails. These rails
+	 * aren't used by anything within the device-tree but are used
+	 * for on board logic level conversion and as rails for
+	 * pull-ups.
+	 */
+	per_pwr: regulator-per-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "per_pwr";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pwr_per_en_default>;
+
+		gpio = <&tlmm 142 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	sdhci_2_vqmmc: regulator-sdhci-2-vqmmc {
+		compatible = "regulator-gpio";
+
+		regulator-name = "sdhci_2_vqmmc";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-type = "voltage";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_vset_default>;
+
+		gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		gpios-states = <0>;
+		states = <3300000 0>,
+			 <1800000 1>;
+
+		startup-delay-us = <10000>;
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+		regulator-always-on;
+		regulator-boot-on;
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+	};
+
+	regulators-3 {
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+	};
+
+	regulators-4 {
+		vdd-s4-supply = <&vph_pwr>;
+	};
+
+	regulators-5 {
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+		vdd-s3-supply = <&vph_pwr>;
+		vdd-s4-supply = <&vph_pwr>;
+		vdd-s5-supply = <&vph_pwr>;
+		vdd-s6-supply = <&vph_pwr>;
+	};
+};
+
+&gpi_dma1 {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&gpu_zap_shader {
+	firmware-name = "qcom/sm8550/a740_zap.mbn";
+	/* Zap shader doesn't load so is disabled */
+	status = "disabled";
+};
+
+&i2c_master_hub_0 {
+	status = "okay";
+};
+
+&i2c_hub_2 {
+	clock-frequency = <400000>;
+	status = "okay";
+
+	ptn3222: redriver@43 {
+		compatible = "nxp,ptn3222";
+		reg = <0x43>;
+		#phy-cells = <0>;
+
+		vdd1v8-supply = <&vreg_l15b_1p8>;
+		vdd3v3-supply = <&vreg_l5b_3p1>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&eusb2_repeater_reset_default>;
+
+		reset-gpios = <&pm8550vs_d_gpios 4 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&ipa {
+	qcom,gsi-loader = "self";
+	memory-region = <&ipa_fw_mem>;
+	firmware-name = "qcom/sm8550/ipa_fws.mbn";
+	status = "okay";
+};
+
+&iris {
+	status = "okay";
+};
+
+&pcie0 {
+	wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+	/*
+	 * pcie0 hosts the M.2 Key-E slot. Apply the SDIO
+	 * reset de-assert here so any module's chip enable is settled
+	 * before pcie0 trains its link.
+	 */
+	pinctrl-0 = <&pcie0_default_state>, <&m2e_sdio_resetn_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1e_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie1 {
+	wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+	perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+
+	/*
+	 * pcie_switch_sel_default and gbe_reset_default are board-init
+	 * lines that must be stable before pcie1 trains its link: the
+	 * PCIe switch needs its mode-select strap settled, and the
+	 * downstream LAN743x must be out of reset to enumerate.
+	 * Applying them via pcie1's pinctrl-0 fires them during
+	 * qcom-pcie probe, before bus enumeration.
+	 */
+	pinctrl-0 = <&pcie1_default_state>,
+		    <&pcie_switch_sel_default>,
+		    <&gbe_reset_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie1_phy {
+	vdda-phy-supply = <&vreg_l3c_0p9>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+	vdda-qref-supply = <&vreg_l1e_0p88>;
+
+	status = "okay";
+};
+
+&pm8550_gpios {
+	sd_card_detect_default: sd-card-detect-default-state {
+		pins = "gpio12";
+		function = "normal";
+		input-enable;
+		output-disable;
+		bias-disable;
+		power-source = <1>; /* 1.8 V */
+	};
+};
+
+&pm8550vs_d_gpios {
+	eusb2_repeater_reset_default: eusb2-repeater-reset-default-state {
+		pins = "gpio4";
+		function = "normal";
+
+		input-enable;
+		output-enable;
+		bias-disable;
+
+		drive-push-pull;
+		power-source = <1>; /* 1.8V */
+		qcom,drive-strength = <3>;
+	};
+};
+
+&pon_pwrkey {
+	status = "okay";
+};
+
+&pon_resin {
+	linux,code = <KEY_VOLUMEDOWN>;
+
+	status = "okay";
+};
+
+&qupv3_id_0 {
+	status = "okay";
+};
+
+&qupv3_id_1 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/sm8550/adsp.mbn",
+			"qcom/sm8550/adsp_dtb.mbn";
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/sm8550/cdsp.mbn",
+			"qcom/sm8550/cdsp_dtb.mbn";
+	status = "okay";
+};
+
+&sdc2_default {
+	clk-pins {
+		drive-strength = <16>;
+	};
+
+	cmd-pins {
+		/delete-property/ bias-pull-up;
+		bias-disable;
+		drive-strength = <16>;
+	};
+
+	data-pins {
+		/delete-property/ bias-pull-up;
+		bias-disable;
+		drive-strength = <16>;
+	};
+};
+
+&sdhc_2 {
+	cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&sdc2_default>, <&sd_card_detect_default>;
+	pinctrl-1 = <&sdc2_default>, <&sd_card_detect_default>;
+	pinctrl-names = "default", "sleep";
+
+	vqmmc-supply = <&sdhci_2_vqmmc>;
+
+	bus-width = <4>;
+	no-sdio;
+	no-mmc;
+
+	status = "okay";
+};
+
+&tlmm {
+	/* Reserved I/Os for NFC */
+	gpio-reserved-ranges = <32 8>;
+
+	pwr_per_en_default: pwr-per-en-default-state {
+		pwr-per-en-pins {
+			pins = "gpio142";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	sd_vset_default: sd-vset-default-state {
+		sd-vset-pins {
+			pins = "gpio4";
+			function = "gpio";
+			drive-strength = <16>;
+			bias-disable;
+		};
+	};
+
+	/*
+	 * Drive LAN743x reset high (de-asserted) when pcie1 probes,
+	 * so the PHY enumerates on the bus.
+	 */
+	gbe_reset_default: gbe-reset-default-state {
+		pins = "gpio138";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	/*
+	 * We drive this GPIO physically high on the M2 Key-E connector
+	 * to make sure the module is enabled. An M2 Key-E module could
+	 * be using this pin as a chip enable.
+	 */
+	m2e_sdio_resetn_default: m2e-sdio-resetn-default-state {
+		pins = "gpio41";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	/* Force the on-board PCIe switch to select the GbE upstream
+	 * port.
+	 */
+	pcie_switch_sel_default: pcie-switch-sel-default-state {
+		pins = "gpio16";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+};
+
+&uart7 {
+	status = "okay";
+};
+
+&ufs_mem_hc {
+	reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+	vcc-supply = <&vreg_l17b_2p5>;
+	vcc-max-microamp = <1300000>;
+	vccq-supply = <&vreg_l1g_1p2>;
+	vccq-max-microamp = <1200000>;
+	vdd-hba-supply = <&vreg_l3g_1p2>;
+
+	status = "okay";
+};
+
+&ufs_mem_phy {
+	vdda-phy-supply = <&vreg_l1d_0p88>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&usb_1 {
+	/delete-property/ usb-role-switch;
+	dr_mode = "peripheral";
+
+	status = "okay";
+};
+
+&usb_1_hsphy {
+	vdd-supply = <&vreg_l1e_0p88>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&ptn3222>;
+
+	status = "okay";
+};
+
+&usb_dp_qmpphy {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3f_0p88>;
+
+	status = "okay";
+};

-- 
2.43.0

Re: [PATCH v3 1/4] dt-bindings: vendor-prefixes: Add IMDT

[Rob Herring (Arm)]

On Thu, 07 May 2026 09:36:40 +0100, William Bright wrote:
> Add IMDT (IMD Technologies Ltd) to the vendor prefixes list.
> 
> Signed-off-by: William Bright <william.bright@imd-tec.com>
> ---
>  Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 

Acked-by: Rob Herring (Arm) <robh@kernel.org>

Re: [PATCH v3 2/4] dt-bindings: arm: qcom: Document IMDT QCS8550 SBC/SoM

[Rob Herring (Arm)]

On Thu, 07 May 2026 09:36:41 +0100, William Bright wrote:
> Document the IMDT QCS8550 SBC which consists of an IMDT QCS8550 SoM
> soldered onto an IMDT QCS8550 carrier board.
> 
> Signed-off-by: William Bright <william.bright@imd-tec.com>
> ---
>  Documentation/devicetree/bindings/arm/qcom.yaml | 7 +++++++
>  1 file changed, 7 insertions(+)
> 

Acked-by: Rob Herring (Arm) <robh@kernel.org>