[PATCH v5 0/3] X2 Elite HP EliteBook X G2q support

[PATCH v5 0/3] X2 Elite HP EliteBook X G2q support

[Jason Pettit]

This series adds initial device-tree support for the HP EliteBook X G2q 14"
Next Gen AI PC (product SKU C4JG0AV, board 8E91), a Snapdragon X2 Elite
(Glymur) laptop.

The board was brought up and validated on real hardware. The electrical
description (PMIC rails, PHY supplies) was verified against the live unit
rather than copied from a Glymur CRD.

Working on this laptop with this series and the Glymur DP PHY series
applied:

  - Internal eDP panel (samsung,atna33xc20)
  - 2x USB Type-C with DisplayPort alt-mode and USB
  - Chassis USB-A host port
  - Fingerprint reader
  - NVMe SSD on PCIe5
  - Wi-Fi, Bluetooth
  - Keyboard, touchpad, touchscreen, lid switch
  - Adreno GPU and GMU (Freedreno GL on Mesa)
  - Audio playback and capture
  - Real-time clock
  - Compute DSP (cDSP)

This patch series builds upon the recent work of Qualcomm engineers to
enable another Glymur-based laptop.

Like its peer submissions, the camera support is missing today.

The audio, GPU and SoCCP series this board previously depended on have
since merged. One runtime dependency remains, the Glymur DP PHY series:

  https://lore.kernel.org/all/20260828-glymur-phy-v3-v3-0-8e73ce7c4636@oss.qualcomm.com/

It is not needed to apply or build this series. With no PHY patches
applied, this series applies cleanly to the base commit below and
qcom/glymur-hp-elitebook-x-g2q.dtb builds without error. The dependency is
runtime only. Without it the DP PHY fails link training and the DisplayPort
outputs do not come up.

The chassis HDMI jack is removed in v5. It is driven from the usb_2 combo
PHY as a DisplayPort-only instance, and that path does not come up on
Glymur. The driver enables the USB half's com_aux clock even on a
DisplayPort-only instance, where nothing powers the block that clock lives
in, so it never ungates and DP init fails with -EBUSY.

This is not specific to this board. The same failure was reported against
the already-merged Asus Zenbook A16 (UX3607OA), which describes its usb_2
combo PHY the same way:

  https://lore.kernel.org/all/20260808164148.123057-1-jesse.casco@gmail.com/

A fix is in progress but not yet available.

arm64 defconfig builds the CPUCP mailbox as a module. SCMI needs it built
in (=y) on Glymur. As a module it loads too late, every SCMI transaction
times out, and cpufreq does not come up on any CPU.

The ADSP and cDSP auto-boot before the rootfs is mounted and do not retry,
so their firmware has to be reachable from the initramfs. With it only on
the rootfs both remoteprocs stay offline and audio does not come up.

The bindings patch 1/3 is independent and can be reviewed/applied on its
own.

Signed-off-by: Jason Pettit <jason.pettit@oss.qualcomm.com>
---
Changes in v5:
- Rebased onto next-20260828.
- Correct the usb_0, usb_1 and usb_mp combo PHY supplies.
- Remove the HDMI path pending a combo PHY driver fix.
- Add the SoCCP firmware names. Drop the redundant status override on that
  node, which glymur.dtsi already leaves enabled.
- Link to v4: https://patch.msgid.link/20260817-glymur-send-v4-0-3fb89cec703e@oss.qualcomm.com

Changes in v4:
- Rebased onto next-20260814. The Glymur combo-PHY configuration patch
  remains the one declared prerequisite.
- Fix the touchpad interrupt. TPAD_INT_N is GPIO 3, not GPIO 66.
- Describe only the microphones this board has. GPIO 200 and GPIO 201, the
  second DMIC clock/data pair, are not connected and are removed in v4.
- Addressed comments received on v3 as reflected in the next two items.
- Use the firmware names from the vendor package (qcadsp8480.mbn,
  adsp_dtbs.elf, qccdsp8480.mbn, cdsp_dtbs.elf)
- Drop the smb2370_l_e2 status override; SMB2370_2 is already disabled by
  "arm64: dts: qcom: smb2370: Disable SMB2370_2 by default".
- Link to v3: https://patch.msgid.link/20260809-glymur-send-v3-0-2d1ed10e3a89@oss.qualcomm.com

Changes in v3:
- Rebased onto next-20260807; the audio, GPU and SoCCP prerequisites have
  merged, leaving only the combo-PHY configuration patch.
- Added the TCSR reference-generator supplies (vdda-qref*/vdda-refgen*) and
  the vreg_l1f_e1_0p88 LDO they reference.
- Set dr_mode = "host" on usb_hs; glymur.dtsi dropped it from that node.
- Reworded the usb_2 and smb2370_l override comments.
- Link to v2: https://patch.msgid.link/20260625-glymur-send-v2-0-00905324ffbf@oss.qualcomm.com

Changes in v2:
- Enable the PMIC RTC (qcom,no-alarm + qcom,uefi-rtc-info)
- Add the SMB2370 eUSB2 repeaters on usb_0/usb_1
- Enable the compute DSP (remoteproc_cdsp / fastrpc)
- Addressed comments from reviewers on v1
- Link to v1: https://lore.kernel.org/linux-arm-msm/20260620-glymur-send-v1-0-fc4a2cfd107c@oss.qualcomm.com

---
Jason Pettit (3):
      dt-bindings: arm: qcom: Add HP EliteBook X G2q 14 AI
      arm64: dts: qcom: Add HP EliteBook X G2q 14 AI
      firmware: qcom: scm: Allow QSEECOM on HP EliteBook X G2q 14 AI

 Documentation/devicetree/bindings/arm/qcom.yaml    |   1 +
 arch/arm64/boot/dts/qcom/Makefile                  |   1 +
 .../boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts    | 940 +++++++++++++++++++++
 drivers/firmware/qcom/qcom_scm.c                   |   1 +
 4 files changed, 943 insertions(+)
---
base-commit: e30626823a406725ce29bc75cb8ec467d3e1e326
change-id: 20260619-glymur-send-1136d243a120

Best regards,
--  
Jason Pettit <jason.pettit@oss.qualcomm.com>

[PATCH v5 1/3] dt-bindings: arm: qcom: Add HP EliteBook X G2q 14 AI

[Jason Pettit]

The HP EliteBook X G2q 14 AI is a Snapdragon X2 Elite (Glymur) laptop.
Document its top-level "hp,elitebook-x-g2q" compatible.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Jason Pettit <jason.pettit@oss.qualcomm.com>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index ff8a35df7862..d141872c2b28 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -87,6 +87,7 @@ properties:
       - items:
           - enum:
               - asus,zenbook-a16-ux3607oa
+              - hp,elitebook-x-g2q
               - qcom,glymur-crd
           - const: qcom,glymur
 

-- 
2.50.1

[PATCH v5 2/3] arm64: dts: qcom: Add HP EliteBook X G2q 14 AI

[Jason Pettit]

Add board support for the HP EliteBook X G2q 14" Next Gen AI PC
(product SKU C4JG0AV, board 8E91), a Snapdragon X2 Elite (Glymur)
laptop, using the "hp,elitebook-x-g2q" / "qcom,glymur" compatible.

Enabled by this device tree:

  - internal eDP panel (samsung,atna33xc20)
  - 2x USB Type-C with DisplayPort alt-mode and USB
  - chassis USB-A host port (usb_mp multiport controller)
  - internal eUSB2 host with the Elan fingerprint reader
  - NVMe SSD on PCIe5
  - Wi-Fi and Bluetooth
  - HID-over-I2C keyboard, touchpad, touchscreen; lid switch
  - Adreno GPU and GMU (Freedreno GL on Mesa)
  - audio playback and capture
  - real-time clock
  - compute DSP (cDSP)

The DisplayPort outputs need the Glymur DP PHY series at runtime. This
device tree builds without it.

The chassis HDMI jack is removed in v5. It is driven from the usb_2
combo PHY as a DisplayPort-only instance, and that path does not come up on
Glymur. The same failure was reported against the already-merged Asus
Zenbook A16 (UX3607OA), which describes its usb_2 combo PHY the same way. A
fix is in progress but not yet available.

Assisted-by: Claude:claude-opus-4-8
Assisted-by: Claude:claude-opus-5
Signed-off-by: Jason Pettit <jason.pettit@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/Makefile                  |   1 +
 .../boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts    | 940 +++++++++++++++++++++
 2 files changed, 941 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 1c86e7e98f55..146955de4606 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= eliza-cqs-evk.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= eliza-mtp.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= glymur-asus-zenbook-a16-ux3607oa.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= glymur-crd.dtb
+dtb-$(CONFIG_ARCH_QCOM)	+= glymur-hp-elitebook-x-g2q.dtb
 dtb-$(CONFIG_ARCH_QCOM)	+= hamoa-iot-evk.dtb
 
 hamoa-iot-evk-el2-dtbs	:= hamoa-iot-evk.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts b/arch/arm64/boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts
new file mode 100644
index 000000000000..096d40e49210
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts
@@ -0,0 +1,940 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include "glymur.dtsi"
+
+#include "pmcx0102.dtsi"
+#include "pmh0101.dtsi"
+#include "pmh0110-glymur.dtsi"
+#include "pmh0104-glymur.dtsi"
+#include "pmk8850.dtsi"
+#include "smb2370.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
+
+/ {
+	model = "HP EliteBook X G2q 14 AI";
+	compatible = "hp,elitebook-x-g2q", "qcom,glymur";
+
+	aliases {
+		i2c0 = &i2c0;
+		i2c8 = &i2c8;
+
+		serial0 = &uart21;
+		serial1 = &uart14;
+	};
+
+	clocks {
+		xo_board: xo-board {
+			compatible = "fixed-clock";
+			clock-frequency = <38400000>;
+			#clock-cells = <0>;
+		};
+
+		sleep_clk: sleep-clk {
+			compatible = "fixed-clock";
+			clock-frequency = <32000>;
+			#clock-cells = <0>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&lid_default>;
+		pinctrl-names = "default";
+
+		switch-lid {
+			label = "lid";
+			gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			wakeup-source;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,glymur-pmic-glink",
+			     "qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* Left side port */
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in: endpoint {
+						remote-endpoint = <&usb_0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in: endpoint {
+						remote-endpoint = <&usb_0_qmpphy_out>;
+					};
+				};
+			};
+		};
+
+		/* Right side port */
+		connector@1 {
+			compatible = "usb-c-connector";
+			reg = <1>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_hs_in1: endpoint {
+						remote-endpoint = <&usb_1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss_in1: endpoint {
+						remote-endpoint = <&usb_1_qmpphy_out>;
+					};
+				};
+			};
+		};
+	};
+
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_nvme: regulator-nvme {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_NVME_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pmh0101_gpios 14 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&nvme_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_wcn_0p95: regulator-wcn-0p95 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_0P95";
+		regulator-min-microvolt = <950000>;
+		regulator-max-microvolt = <950000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_3p3: regulator-wcn-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 94 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&wcn_sw_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	sound {
+		compatible = "qcom,glymur-sndcard";
+		model = "GLYMUR-HP-EliteBook-X-G2q";
+
+		audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
+				"TweeterLeft IN", "WSA WSA_SPK2 OUT",
+				"WooferRight IN", "WSA2 WSA_SPK1 OUT",
+				"TweeterRight IN", "WSA2 WSA_SPK2 OUT",
+				"VA DMIC0", "vdd-micb",
+				"VA DMIC1", "vdd-micb";
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			codec {
+				sound-dai = <&left_woofer>, <&left_tweeter>,
+					    <&swr0 0>, <&lpass_wsamacro 0>,
+					    <&right_woofer>, <&right_tweeter>,
+					    <&swr3 0>, <&lpass_wsa2macro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		vdd-supply = <&vreg_wcn_0p95>;
+		vddio-supply = <&vreg_l15b_e0_1p8>;
+		vddaon-supply = <&vreg_l15b_e0_1p8>;
+		vdddig-supply = <&vreg_l15b_e0_1p8>;
+		vddrfa1p2-supply = <&vreg_l15b_e0_1p8>;
+		vddrfa1p8-supply = <&vreg_l15b_e0_1p8>;
+
+		wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&wcn_wlan_bt_en>;
+		pinctrl-names = "default";
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pmh0101-rpmh-regulators";
+		qcom,pmic-id = "B_E0";
+
+		vreg_l1b_e0_1p8: ldo1 {
+			regulator-name = "vreg_l1b_e0_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_e0_3p1: ldo7 {
+			regulator-name = "vreg_l7b_e0_3p1";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_e0_1p8: ldo15 {
+			regulator-name = "vreg_l15b_e0_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l18b_e0_1p2: ldo18 {
+			regulator-name = "vreg_l18b_e0_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pmcx0102-rpmh-regulators";
+		qcom,pmic-id = "C_E1";
+
+		vreg_l1c_e1_0p91: ldo1 {
+			regulator-name = "vreg_l1c_e1_0p91";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pmh0110-rpmh-regulators";
+		qcom,pmic-id = "F_E0";
+
+		vreg_l2f_e0_0p94: ldo2 {
+			regulator-name = "vreg_l2f_e0_0p94";
+			regulator-min-microvolt = <936000>;
+			regulator-max-microvolt = <936000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_e0_0p91: ldo3 {
+			regulator-name = "vreg_l3f_e0_0p91";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pmh0110-rpmh-regulators";
+		qcom,pmic-id = "F_E1";
+
+		vreg_l1f_e1_0p88: ldo1 {
+			regulator-name = "vreg_l1f_e1_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_e1_0p88: ldo2 {
+			regulator-name = "vreg_l2f_e1_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4f_e1_1p2: ldo4 {
+			regulator-name = "vreg_l4f_e1_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pmh0110-rpmh-regulators";
+		qcom,pmic-id = "H_E0";
+
+		vreg_l1h_e0_0p94: ldo1 {
+			regulator-name = "vreg_l1h_e0_0p94";
+			regulator-min-microvolt = <936000>;
+			regulator-max-microvolt = <936000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2h_e0_0p88: ldo2 {
+			regulator-name = "vreg_l2h_e0_0p88";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4h_e0_1p2: ldo4 {
+			regulator-name = "vreg_l4h_e0_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&gmu {
+	status = "okay";
+};
+
+&gpu {
+	status = "okay";
+};
+
+&i2c0 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+
+		hid-descr-addr = <0x20>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&tpad_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+
+	keyboard@3a {
+		compatible = "hid-over-i2c";
+		reg = <0x3a>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-0 = <&kybd_default>;
+		pinctrl-names = "default";
+
+		wakeup-source;
+	};
+};
+
+&i2c8 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <200>;
+
+		pinctrl-0 = <&ts0_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&lpass_vamacro {
+	vdd-micb-supply = <&vreg_l1b_e0_1p8>;
+
+	pinctrl-0 = <&dmic01_default>;
+	pinctrl-names = "default";
+
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp1 {
+	status = "okay";
+};
+
+&mdss_dp1_out {
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+	/delete-property/ #sound-dai-cells;
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "samsung,atna33xc20";
+			enable-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+			power-supply = <&vreg_edp_3p3>;
+
+			pinctrl-0 = <&edp_bl_en>;
+			pinctrl-names = "default";
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+};
+
+&mdss_dp3_out {
+	data-lanes = <0 1 2 3>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+	remote-endpoint = <&edp_panel_in>;
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l2f_e1_0p88>;
+	vdda-pll-supply = <&vreg_l4f_e1_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	pinctrl-0 = <&pcie4_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l1c_e1_0p91>;
+	vdda-pll-supply = <&vreg_l4f_e1_1p2>;
+
+	status = "okay";
+};
+
+&pcie4_port0 {
+	reset-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
+&pcie5 {
+	vddpe-3v3-supply = <&vreg_nvme>;
+
+	pinctrl-0 = <&pcie5_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie5_phy {
+	vdda-phy-supply = <&vreg_l2f_e0_0p94>;
+	vdda-pll-supply = <&vreg_l4h_e0_1p2>;
+
+	status = "okay";
+};
+
+&pcie5_port0 {
+	reset-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&pmh0101_gpios {
+	nvme_reg_en: nvme-reg-en-state {
+		pins = "gpio14";
+		function = "normal";
+		bias-disable;
+	};
+};
+
+&pmk8850_rtc {
+	qcom,no-alarm;
+	qcom,uefi-rtc-info;
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/glymur/hp/elitebook-x-g2q/qcadsp8480.mbn",
+			"qcom/glymur/hp/elitebook-x-g2q/adsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/glymur/hp/elitebook-x-g2q/qccdsp8480.mbn",
+			"qcom/glymur/hp/elitebook-x-g2q/cdsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&remoteproc_soccp {
+	firmware-name = "qcom/glymur/hp/elitebook-x-g2q/soccp.mbn",
+			"qcom/glymur/hp/elitebook-x-g2q/soccp_dtb.mbn";
+};
+
+&smb2370_j_e2_eusb2_repeater {
+	vdd18-supply = <&vreg_l15b_e0_1p8>;
+	vdd3-supply = <&vreg_l7b_e0_3p1>;
+};
+
+&smb2370_k_e2_eusb2_repeater {
+	vdd18-supply = <&vreg_l15b_e0_1p8>;
+	vdd3-supply = <&vreg_l7b_e0_3p1>;
+};
+
+&swr0 {
+	status = "okay";
+
+	/* WSA8845, left woofer */
+	left_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferLeft";
+		vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+		vdd-io-supply = <&vreg_l18b_e0_1p2>;
+		qcom,port-mapping = <1 2 3 7 12 14>;
+	};
+
+	/* WSA8845, left tweeter */
+	left_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterLeft";
+		vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+		vdd-io-supply = <&vreg_l18b_e0_1p2>;
+		qcom,port-mapping = <4 5 6 7 13 15>;
+	};
+};
+
+&swr3 {
+	status = "okay";
+
+	/* WSA8845, right woofer */
+	right_woofer: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "WooferRight";
+		vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+		vdd-io-supply = <&vreg_l18b_e0_1p2>;
+		qcom,port-mapping = <1 2 3 7 12 14>;
+	};
+
+	/* WSA8845, right tweeter */
+	right_tweeter: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "TweeterRight";
+		vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+		vdd-io-supply = <&vreg_l18b_e0_1p2>;
+		qcom,port-mapping = <4 5 6 7 13 15>;
+	};
+};
+
+&tcsr {
+	vdda-qrefrpt0-0p9-supply = <&vreg_l2f_e1_0p88>;
+	vdda-qrefrpt1-0p9-supply = <&vreg_l2f_e1_0p88>;
+	vdda-qrefrpt2-0p9-supply = <&vreg_l2f_e1_0p88>;
+	vdda-qrefrpt3-0p9-supply = <&vreg_l2h_e0_0p88>;
+	vdda-qrefrpt4-0p9-supply = <&vreg_l2h_e0_0p88>;
+	vdda-qrefrx0-0p9-supply = <&vreg_l2f_e1_0p88>;
+	vdda-qrefrx1-0p9-supply = <&vreg_l2f_e1_0p88>;
+	vdda-qrefrx2-0p9-supply = <&vreg_l2f_e1_0p88>;
+	vdda-qrefrx4-0p9-supply = <&vreg_l2h_e0_0p88>;
+	vdda-qrefrx5-0p9-supply = <&vreg_l3f_e0_0p91>;
+	vdda-qreftx0-0p9-supply = <&vreg_l3f_e0_0p91>;
+	vdda-qreftx0-1p2-supply = <&vreg_l4h_e0_1p2>;
+	vdda-qreftx1-0p9-supply = <&vreg_l1f_e1_0p88>;
+	vdda-refgen3-0p9-supply = <&vreg_l2f_e0_0p94>;
+	vdda-refgen3-1p2-supply = <&vreg_l4h_e0_1p2>;
+	vdda-refgen4-0p9-supply = <&vreg_l1f_e1_0p88>;
+	vdda-refgen4-1p2-supply = <&vreg_l4f_e1_1p2>;
+};
+
+&tlmm {
+	gpio-reserved-ranges = <4 4>, /* EC TZ Secure I3C */
+			       <10 2>, /* OOB UART */
+			       <44 4>, /* Security SPI (TPM) */
+			       <65 1>; /* EC reset */
+
+	tpad_default: tpad-default-state {
+		pins = "gpio3";
+		function = "gpio";
+		bias-disable;
+	};
+
+	edp_bl_en: edp-bl-en-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	ts0_default: ts0-default-state {
+		pins = "gpio51";
+		function = "gpio";
+		bias-disable;
+	};
+
+	kybd_default: kybd-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		bias-disable;
+	};
+
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio70";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	lid_default: lid-default-state {
+		pins = "gpio92";
+		function = "gpio";
+		bias-disable;
+	};
+
+	wcn_sw_en: wcn-sw-en-state {
+		pins = "gpio94";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	wcn_wlan_bt_en: wcn-wlan-bt-en-state {
+		pins = "gpio116", "gpio117";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie4_default: pcie4-default-state {
+		clkreq-n-pins {
+			pins = "gpio147";
+			function = "pcie4_clk_req_n";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio146";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio148";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie5_default: pcie5-default-state {
+		clkreq-n-pins {
+			pins = "gpio153";
+			function = "pcie5_clk_req_n";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio152";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio154";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+		max-speed = <3200000>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+	};
+};
+
+&usb_0 {
+	status = "okay";
+};
+
+&usb_0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_0_hsphy {
+	vdd-supply = <&vreg_l3f_e0_0p91>;
+	vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+	phys = <&smb2370_j_e2_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy {
+	vdda-phy-supply = <&vreg_l3f_e0_0p91>;
+	vdda-pll-supply = <&vreg_l4h_e0_1p2>;
+	refgen-supply = <&vreg_l2f_e0_0p94>;
+
+	status = "okay";
+};
+
+&usb_0_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&usb_1 {
+	status = "okay";
+};
+
+&usb_1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_hs_in1>;
+};
+
+&usb_1_hsphy {
+	vdd-supply = <&vreg_l3f_e0_0p91>;
+	vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+	phys = <&smb2370_k_e2_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy {
+	vdda-phy-supply = <&vreg_l1h_e0_0p94>;
+	vdda-pll-supply = <&vreg_l4h_e0_1p2>;
+	refgen-supply = <&vreg_l2f_e0_0p94>;
+
+	status = "okay";
+};
+
+&usb_1_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss_in1>;
+};
+
+/* Internal USB2 host for the Elan fingerprint reader (usb 04f3:0ca8). */
+&usb_hs {
+	dr_mode = "host";
+
+	status = "okay";
+};
+
+&usb_hs_phy {
+	vdd-supply = <&vreg_l2h_e0_0p88>;
+	vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+	status = "okay";
+};
+
+/* Multiport host: port 0 = chassis USB-A, port 1 = internal USB HID. */
+&usb_mp {
+	status = "okay";
+};
+
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2h_e0_0p88>;
+	vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+	status = "okay";
+};
+
+&usb_mp_hsphy1 {
+	vdd-supply = <&vreg_l2h_e0_0p88>;
+	vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l2h_e0_0p88>;
+	vdda-pll-supply = <&vreg_l4h_e0_1p2>;
+	refgen-supply = <&vreg_l4f_e1_1p2>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+	vdda-phy-supply = <&vreg_l2h_e0_0p88>;
+	vdda-pll-supply = <&vreg_l4h_e0_1p2>;
+	refgen-supply = <&vreg_l4f_e1_1p2>;
+
+	status = "okay";
+};

-- 
2.50.1

[PATCH v5 3/3] firmware: qcom: scm: Allow QSEECOM on HP EliteBook X G2q 14 AI

[Jason Pettit]

The HP EliteBook X G2q 14" Next Gen AI PC is a Snapdragon X2 Elite
(Glymur) laptop whose firmware exposes EFI variables through QSEECOM.
Add its board compatible to the QSEECOM allowlist so that EFI variable
access (efivarfs) works on this machine.

Without it the kernel reports "qseecom: untested machine, skipping" and
efivarfs is empty.

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Signed-off-by: Jason Pettit <jason.pettit@oss.qualcomm.com>
---
 drivers/firmware/qcom/qcom_scm.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index 3eaa4c9ccf3c..c44c63e1c20d 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -2311,6 +2311,7 @@ static const struct of_device_id qcom_scm_qseecom_allowlist[] __maybe_unused = {
 	{ .compatible = "ecs,liva-qc710" },
 	{ .compatible = "honor,magicbook-art-14-snapdragon" },
 	{ .compatible = "hp,elitebook-ultra-g1q" },
+	{ .compatible = "hp,elitebook-x-g2q" },
 	{ .compatible = "hp,omnibook-x14" },
 	{ .compatible = "huawei,gaokun3" },
 	{ .compatible = "lenovo,flex-5g" },

-- 
2.50.1

Re: [PATCH v5 2/3] arm64: dts: qcom: Add HP EliteBook X G2q 14 AI

[Konrad Dybcio]

On 8/29/26 9:08 PM, Jason Pettit wrote:
> Add board support for the HP EliteBook X G2q 14" Next Gen AI PC
> (product SKU C4JG0AV, board 8E91), a Snapdragon X2 Elite (Glymur)
> laptop, using the "hp,elitebook-x-g2q" / "qcom,glymur" compatible.
> 
> Enabled by this device tree:
> 
>   - internal eDP panel (samsung,atna33xc20)
>   - 2x USB Type-C with DisplayPort alt-mode and USB
>   - chassis USB-A host port (usb_mp multiport controller)
>   - internal eUSB2 host with the Elan fingerprint reader
>   - NVMe SSD on PCIe5
>   - Wi-Fi and Bluetooth
>   - HID-over-I2C keyboard, touchpad, touchscreen; lid switch
>   - Adreno GPU and GMU (Freedreno GL on Mesa)
>   - audio playback and capture
>   - real-time clock
>   - compute DSP (cDSP)
> 
> The DisplayPort outputs need the Glymur DP PHY series at runtime. This
> device tree builds without it.
> 
> The chassis HDMI jack is removed in v5. It is driven from the usb_2
> combo PHY as a DisplayPort-only instance, and that path does not come up on
> Glymur. The same failure was reported against the already-merged Asus
> Zenbook A16 (UX3607OA), which describes its usb_2 combo PHY the same way. A
> fix is in progress but not yet available.

FWIW this paragraph would be better suited to go under the --- line
(the part that doesn't go into the git log), but it's fine

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH v5 2/3] arm64: dts: qcom: Add HP EliteBook X G2q 14 AI

[Abel Vesa]

On 26-08-29 12:08:09, Jason Pettit wrote:
> Add board support for the HP EliteBook X G2q 14" Next Gen AI PC
> (product SKU C4JG0AV, board 8E91), a Snapdragon X2 Elite (Glymur)
> laptop, using the "hp,elitebook-x-g2q" / "qcom,glymur" compatible.
> 
> Enabled by this device tree:
> 
>   - internal eDP panel (samsung,atna33xc20)
>   - 2x USB Type-C with DisplayPort alt-mode and USB
>   - chassis USB-A host port (usb_mp multiport controller)
>   - internal eUSB2 host with the Elan fingerprint reader
>   - NVMe SSD on PCIe5
>   - Wi-Fi and Bluetooth
>   - HID-over-I2C keyboard, touchpad, touchscreen; lid switch
>   - Adreno GPU and GMU (Freedreno GL on Mesa)
>   - audio playback and capture
>   - real-time clock
>   - compute DSP (cDSP)
> 
> The DisplayPort outputs need the Glymur DP PHY series at runtime. This
> device tree builds without it.
> 
> The chassis HDMI jack is removed in v5. It is driven from the usb_2
> combo PHY as a DisplayPort-only instance, and that path does not come up on
> Glymur. The same failure was reported against the already-merged Asus
> Zenbook A16 (UX3607OA), which describes its usb_2 combo PHY the same way. A
> fix is in progress but not yet available.

No point of having this in the commit message, as Konrad also pointed
out.

> 
> Assisted-by: Claude:claude-opus-4-8
> Assisted-by: Claude:claude-opus-5
> Signed-off-by: Jason Pettit <jason.pettit@oss.qualcomm.com>

With the comments addressed:

Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>

> ---
>  arch/arm64/boot/dts/qcom/Makefile                  |   1 +
>  .../boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts    | 940 +++++++++++++++++++++
>  2 files changed, 941 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 1c86e7e98f55..146955de4606 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -18,6 +18,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= eliza-cqs-evk.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= eliza-mtp.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= glymur-asus-zenbook-a16-ux3607oa.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= glymur-crd.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= glymur-hp-elitebook-x-g2q.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= hamoa-iot-evk.dtb
>  
>  hamoa-iot-evk-el2-dtbs	:= hamoa-iot-evk.dtb x1-el2.dtbo
> diff --git a/arch/arm64/boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts b/arch/arm64/boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts
> new file mode 100644
> index 000000000000..096d40e49210
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts
> @@ -0,0 +1,940 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
> + */
> +/dts-v1/;
> +

[...]

> +&i2c8 {
> +	clock-frequency = <400000>;
> +
> +	status = "okay";
> +
> +	touchscreen@10 {
> +		compatible = "hid-over-i2c";
> +		reg = <0x10>;
> +
> +		hid-descr-addr = <0x1>;
> +		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
> +
> +		post-power-on-delay-ms = <200>;

No supplies?

Re: (subset) [PATCH v5 0/3] X2 Elite HP EliteBook X G2q support

[Bjorn Andersson]

On Sat, 29 Aug 2026 12:08:07 -0700, Jason Pettit wrote:
> This series adds initial device-tree support for the HP EliteBook X G2q 14"
> Next Gen AI PC (product SKU C4JG0AV, board 8E91), a Snapdragon X2 Elite
> (Glymur) laptop.
> 
> The board was brought up and validated on real hardware. The electrical
> description (PMIC rails, PHY supplies) was verified against the live unit
> rather than copied from a Glymur CRD.
> 
> [...]

Applied, thanks!

[3/3] firmware: qcom: scm: Allow QSEECOM on HP EliteBook X G2q 14 AI
      commit: 665d237915193b06d3026da367040e4a4f3356ba

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>

Re: [PATCH v5 2/3] arm64: dts: qcom: Add HP EliteBook X G2q 14 AI

[Bjorn Andersson]

On Sat, Aug 29, 2026 at 12:08:09PM -0700, Jason Pettit wrote:
> Add board support for the HP EliteBook X G2q 14" Next Gen AI PC
> (product SKU C4JG0AV, board 8E91), a Snapdragon X2 Elite (Glymur)
> laptop, using the "hp,elitebook-x-g2q" / "qcom,glymur" compatible.
> 
> Enabled by this device tree:
> 
>   - internal eDP panel (samsung,atna33xc20)
>   - 2x USB Type-C with DisplayPort alt-mode and USB
>   - chassis USB-A host port (usb_mp multiport controller)
>   - internal eUSB2 host with the Elan fingerprint reader
>   - NVMe SSD on PCIe5
>   - Wi-Fi and Bluetooth
>   - HID-over-I2C keyboard, touchpad, touchscreen; lid switch
>   - Adreno GPU and GMU (Freedreno GL on Mesa)
>   - audio playback and capture
>   - real-time clock
>   - compute DSP (cDSP)
> 
> The DisplayPort outputs need the Glymur DP PHY series at runtime. This
> device tree builds without it.
> 
> The chassis HDMI jack is removed in v5. It is driven from the usb_2
> combo PHY as a DisplayPort-only instance, and that path does not come up on
> Glymur. The same failure was reported against the already-merged Asus
> Zenbook A16 (UX3607OA), which describes its usb_2 combo PHY the same way. A
> fix is in progress but not yet available.
> 

I dropped this paragraph while applying the patch.

> Assisted-by: Claude:claude-opus-4-8
> Assisted-by: Claude:claude-opus-5

This should from now on be "Assisted-by: LLM".

Regards,
Bjorn