* [PATCH v2 12/12] tpm/tpm_tis_spi: Add support for spi phy
[not found] ` <1460577351-24632-1-git-send-email-christophe-h.ricard-qxv4g6HH51o@public.gmane.org>
2016-04-13 19:55 ` [PATCH v2 09/12] devicetree: Add infineon to vendor-prefix.txt Christophe Ricard
2016-04-13 19:55 ` [PATCH v2 10/12] devicetree: Add Trusted Computing Group " Christophe Ricard
@ 2016-04-13 19:55 ` Christophe Ricard
[not found] ` <1460577351-24632-13-git-send-email-christophe-h.ricard-qxv4g6HH51o@public.gmane.org>
2 siblings, 1 reply; 4+ messages in thread
From: Christophe Ricard @ 2016-04-13 19:55 UTC (permalink / raw)
To: jarkko.sakkinen-VuQAYsv1563Yd54FQh9/CA
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA, jean-luc.blanc-qxv4g6HH51o,
ashley-fm2HMyfA2y6tG0bUXCXiUA,
tpmdd-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f,
christophe-h.ricard-qxv4g6HH51o, Peter Huewe,
benoit.houyere-qxv4g6HH51o
Spi protocol standardized by the TCG is now supported by most of TPM
vendors.
It supports SPI Bit Protocol as describe in the TCG PTP
specification (chapter 6.4.6 SPI Bit Protocol).
Irq mode is not supported.
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Signed-off-by: Peter Huewe <peter.huewe-d0qZbvYSIPpWk0Htik3J/w@public.gmane.org>
Signed-off-by: Alexander Steffen <Alexander.Steffen-d0qZbvYSIPpWk0Htik3J/w@public.gmane.org>
Signed-off-by: Christophe Ricard <christophe-h.ricard-qxv4g6HH51o@public.gmane.org>
---
.../bindings/security/tpm/tpm_tis_spi.txt | 21 ++
drivers/char/tpm/Kconfig | 12 +
drivers/char/tpm/Makefile | 1 +
drivers/char/tpm/tpm_tis_spi.c | 242 +++++++++++++++++++++
4 files changed, 276 insertions(+)
create mode 100644 Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt
create mode 100644 drivers/char/tpm/tpm_tis_spi.c
diff --git a/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt b/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt
new file mode 100644
index 0000000..31f4dcd
--- /dev/null
+++ b/Documentation/devicetree/bindings/security/tpm/tpm_tis_spi.txt
@@ -0,0 +1,21 @@
+Required properties:
+- compatible: Should be "st,st33htpm-spi" or "infineon,slb9670" or "tcg,tpm_tis-spi"
+- spi-max-frequency: Maximum SPI frequency (depends on TPMs).
+
+Optional SoC Specific Properties:
+- pinctrl-names: Contains only one value - "default".
+- pintctrl-0: Specifies the pin control groups used for this controller.
+
+Example (for ARM-based BeagleBoard xM with TPM_TIS on SPI4):
+
+&mcspi4 {
+
+ status = "okay";
+
+ tpm_tis@0 {
+
+ compatible = "tcg,tpm_tis-spi";
+
+ spi-max-frequency = <10000000>;
+ };
+};
diff --git a/drivers/char/tpm/Kconfig b/drivers/char/tpm/Kconfig
index b217308..a8ab570 100644
--- a/drivers/char/tpm/Kconfig
+++ b/drivers/char/tpm/Kconfig
@@ -41,6 +41,18 @@ config TCG_TIS
within Linux. To compile this driver as a module, choose M here;
the module will be called tpm_tis.
+config TCG_TIS_SPI
+ tristate "TPM Interface Specification 1.3 Interface / TPM 2.0 FIFO Interface - (SPI)"
+ depends on SPI
+ select TCG_TIS_CORE
+ ---help---
+ If you have a TPM security chip which is connected to a regular,
+ non-tcg SPI master (i.e. most embedded platforms) that is compliant with the
+ TCG TIS 1.3 TPM specification (TPM1.2) or the TCG PTP FIFO
+ specification (TPM2.0) say Yes and it will be accessible from
+ within Linux. To compile this driver as a module, choose M here;
+ the module will be called tpm_tis_spi.
+
config TCG_TIS_I2C_ATMEL
tristate "TPM Interface Specification 1.2 Interface (I2C - Atmel)"
depends on I2C
diff --git a/drivers/char/tpm/Makefile b/drivers/char/tpm/Makefile
index 80be5b2..5c08374 100644
--- a/drivers/char/tpm/Makefile
+++ b/drivers/char/tpm/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_TCG_TIS) += tpm_tis.o
obj-$(CONFIG_TCG_TIS_I2C_ATMEL) += tpm_i2c_atmel.o
obj-$(CONFIG_TCG_TIS_I2C_INFINEON) += tpm_i2c_infineon.o
obj-$(CONFIG_TCG_TIS_I2C_NUVOTON) += tpm_i2c_nuvoton.o
+obj-$(CONFIG_TCG_TIS_SPI) += tpm_tis_spi.o
obj-$(CONFIG_TCG_NSC) += tpm_nsc.o
obj-$(CONFIG_TCG_ATMEL) += tpm_atmel.o
obj-$(CONFIG_TCG_INFINEON) += tpm_infineon.o
diff --git a/drivers/char/tpm/tpm_tis_spi.c b/drivers/char/tpm/tpm_tis_spi.c
new file mode 100644
index 0000000..fe6a684
--- /dev/null
+++ b/drivers/char/tpm/tpm_tis_spi.c
@@ -0,0 +1,242 @@
+/*
+ * Copyright (C) 2015 Infineon Technologies AG
+ * Copyright (C) 2016 STMicroelectronics SAS
+ *
+ * Authors:
+ * Peter Huewe <peter.huewe-d0qZbvYSIPpWk0Htik3J/w@public.gmane.org>
+ * Christophe Ricard <christophe-h.ricard-qxv4g6HH51o@public.gmane.org>
+ *
+ * Maintained by: <tpmdd-devel-5NWGOfrQmneRv+LV9MX5uipxlwaOVQ5f@public.gmane.org>
+ *
+ * Device driver for TCG/TCPA TPM (trusted platform module).
+ * Specifications at www.trustedcomputinggroup.org
+ *
+ * This device driver implements the TPM interface as defined in
+ * the TCG TPM Interface Spec version 1.3, revision 27 via _raw/native
+ * SPI access_.
+ *
+ * It is based on the original tpm_tis device driver from Leendert van
+ * Dorn and Kyleen Hall and Jarko Sakkinnen.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation, version 2 of the
+ * License.
+ */
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/slab.h>
+#include <linux/interrupt.h>
+#include <linux/wait.h>
+#include <linux/acpi.h>
+#include <linux/freezer.h>
+
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+#include <linux/gpio.h>
+#include <linux/of_irq.h>
+#include <linux/of_gpio.h>
+#include <linux/tpm.h>
+#include "tpm.h"
+#include "tpm_tis_core.h"
+
+#define MAX_SPI_FRAMESIZE 64
+
+struct tpm_tis_spi_phy {
+ struct spi_device *spi_device;
+
+ u8 tx_buf[MAX_SPI_FRAMESIZE + 4];
+ u8 rx_buf[MAX_SPI_FRAMESIZE + 4];
+};
+
+static int tpm_tis_spi_read_bytes(struct tpm_chip *chip, u32 addr,
+ u16 len, u8 *result)
+{
+ struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
+ struct tpm_tis_spi_phy *phy = priv->phy_id;
+ int ret;
+ struct spi_message m;
+ struct spi_transfer spi_xfer = {
+ .tx_buf = phy->tx_buf,
+ .rx_buf = phy->rx_buf,
+ .len = 4,
+ };
+
+ if (len > MAX_SPI_FRAMESIZE)
+ return -ENOMEM;
+
+ phy->tx_buf[0] = 0x80 | (len - 1);
+ phy->tx_buf[1] = 0xd4;
+ phy->tx_buf[2] = (addr >> 8) & 0xFF;
+ phy->tx_buf[3] = addr & 0xFF;
+
+ spi_xfer.cs_change = 1;
+ spi_message_init(&m);
+ spi_message_add_tail(&spi_xfer, &m);
+
+ spi_bus_lock(phy->spi_device->master);
+ ret = spi_sync_locked(phy->spi_device, &m);
+ if (ret < 0)
+ goto exit;
+
+ memset(phy->tx_buf, 0, len);
+
+ /* According to TCG PTP specification, if there is no TPM present at
+ * all, then the design has a weak pull-up on MISO. If a TPM is not
+ * present, a pull-up on MISO means that the SB controller sees a 1,
+ * and will latch in 0xFF on the read.
+ */
+ for ( ; (phy->rx_buf[0] & 0x01) == 0 ; ) {
+ spi_xfer.len = 1;
+ spi_message_init(&m);
+ spi_message_add_tail(&spi_xfer, &m);
+ ret = spi_sync_locked(phy->spi_device, &m);
+ if (ret < 0)
+ goto exit;
+ }
+
+ spi_xfer.cs_change = 0;
+ spi_xfer.len = len;
+ spi_xfer.rx_buf = result;
+
+ spi_message_init(&m);
+ spi_message_add_tail(&spi_xfer, &m);
+ ret = spi_sync_locked(phy->spi_device, &m);
+
+exit:
+ spi_bus_unlock(phy->spi_device->master);
+ return ret;
+}
+
+static int tpm_tis_spi_write_bytes(struct tpm_chip *chip, u32 addr,
+ u16 len, u8 *value)
+{
+ int ret;
+ struct tpm_tis_data *priv = dev_get_drvdata(&chip->dev);
+ struct tpm_tis_spi_phy *phy = priv->phy_id;
+ struct spi_message m;
+ struct spi_transfer spi_xfer = {
+ .tx_buf = phy->tx_buf,
+ .rx_buf = phy->rx_buf,
+ .len = 4,
+ };
+
+ if (len > MAX_SPI_FRAMESIZE)
+ return -ENOMEM;
+
+ phy->tx_buf[0] = len - 1;
+ phy->tx_buf[1] = 0xd4;
+ phy->tx_buf[2] = (addr >> 8) & 0xFF;
+ phy->tx_buf[3] = addr & 0xFF;
+
+ spi_xfer.cs_change = 1;
+ spi_message_init(&m);
+ spi_message_add_tail(&spi_xfer, &m);
+
+ spi_bus_lock(phy->spi_device->master);
+ ret = spi_sync_locked(phy->spi_device, &m);
+ if (ret < 0)
+ goto exit;
+
+ memset(phy->tx_buf, 0, len);
+
+ /* According to TCG PTP specification, if there is no TPM present at
+ * all, then the design has a weak pull-up on MISO. If a TPM is not
+ * present, a pull-up on MISO means that the SB controller sees a 1,
+ * and will latch in 0xFF on the read.
+ */
+ for ( ; (phy->rx_buf[0] & 0x01) == 0 ; ) {
+ spi_xfer.len = 1;
+ spi_message_init(&m);
+ spi_message_add_tail(&spi_xfer, &m);
+ ret = spi_sync_locked(phy->spi_device, &m);
+ if (ret < 0)
+ goto exit;
+ }
+
+ spi_xfer.len = len;
+ spi_xfer.tx_buf = value;
+ spi_xfer.cs_change = 0;
+ spi_xfer.tx_buf = value;
+ spi_message_init(&m);
+ spi_message_add_tail(&spi_xfer, &m);
+ ret = spi_sync_locked(phy->spi_device, &m);
+
+exit:
+ spi_bus_unlock(phy->spi_device->master);
+ return ret;
+}
+
+static const struct tpm_tis_class_lowlevel tpm_spi_lowlevel = {
+ .read_bytes = tpm_tis_spi_read_bytes,
+ .write_bytes = tpm_tis_spi_write_bytes,
+};
+
+static int tpm_tis_spi_probe(struct spi_device *dev)
+{
+ struct tpm_tis_spi_phy *phy;
+
+ /* Check SPI platform functionnalities */
+ if (!dev) {
+ pr_err("%s: dev is NULL. Device is not accessible.\n",
+ __func__);
+ return -ENODEV;
+ }
+
+ phy = devm_kzalloc(&dev->dev, sizeof(struct tpm_tis_spi_phy),
+ GFP_KERNEL);
+ if (!phy)
+ return -ENOMEM;
+
+ phy->spi_device = dev;
+
+ return tpm_tis_core_init(&dev->dev, phy, -1, &tpm_spi_lowlevel,
+ NULL, NULL);
+}
+
+static int tpm_tis_spi_remove(struct spi_device *dev)
+{
+ struct tpm_chip *chip = spi_get_drvdata(dev);
+
+ tpm_chip_unregister(chip);
+ return 0;
+}
+
+static const struct spi_device_id tpm_tis_spi_id[] = {
+ {"tpm_tis_spi", 0},
+ {}
+};
+MODULE_DEVICE_TABLE(spi, tpm_tis_spi_id);
+
+static const struct of_device_id of_tis_spi_match[] = {
+ { .compatible = "st,st33htpm-spi", },
+ { .compatible = "infineon,slb9670", },
+ { .compatible = "tcg,tpm_tis-spi", },
+ {}
+};
+MODULE_DEVICE_TABLE(of, of_tis_spi_match);
+
+static const struct acpi_device_id acpi_tis_spi_match[] = {
+ {"SMO0768", 0},
+ {}
+};
+MODULE_DEVICE_TABLE(acpi, acpi_tis_spi_match);
+
+static struct spi_driver tpm_tis_spi_driver = {
+ .driver = {
+ .owner = THIS_MODULE,
+ .name = "tpm_tis_spi",
+ .pm = &tpm_tis_pm,
+ .of_match_table = of_match_ptr(of_tis_spi_match),
+ .acpi_match_table = ACPI_PTR(acpi_tis_spi_match),
+ },
+ .probe = tpm_tis_spi_probe,
+ .remove = tpm_tis_spi_remove,
+ .id_table = tpm_tis_spi_id,
+};
+module_spi_driver(tpm_tis_spi_driver);
+
+MODULE_DESCRIPTION("TPM Driver for native SPI access");
+MODULE_LICENSE("GPL");
--
2.5.0
------------------------------------------------------------------------------
Find and fix application performance issues faster with Applications Manager
Applications Manager provides deep performance insights into multiple tiers of
your business applications. It resolves application problems quickly and
reduces your MTTR. Get your free trial!
https://ad.doubleclick.net/ddm/clk/302982198;130105516;z
^ permalink raw reply related [flat|nested] 4+ messages in thread