[v3 PATCH 0/5] Rockchip Type-C and DispplayPort driver

[v3 PATCH 0/5] Rockchip Type-C and DispplayPort driver

[Chris Zhong]

Hi all

This series patch is for rockchip Type-C phy and DisplayPort controller
driver.

The USB Type-C PHY is designed to support the USB3 and DP applications.
The PHY basically has two main components: USB3 and DisplyPort. USB3
operates in SuperSpeed mode and the DP can operate at RBR, HBR and HBR2
data rates. The Type-C cable orientation detection and Power Delivery
(PD) is accomplished using a PD PHY or a exernal PD chip.

The DP controller is compliant with DisplayPort Specification,
Version 1.3, This IP is compatible with the rockchip type-c PHY IP.
There is a uCPU in DP controller, it need a firmware to work, please
put the firmware file to /lib/firmware/cdn/dptx.bin. The uCPU in charge
of aux communication and link training, the host use mailbox to
communicate with the ucpu.

The PHY driver has register a notification with extcon API, to get the
alt mode from PD, the PD driver need call the devm_extcon_dev_allocate
to create a extcon device and use extcon_set_state to notify PHY and
DP controller.

About the DP audio, cdn-dp registered 2 DAIs: 0 is I2S, 1 is SPDIF.
We can reference them in simple-card.

This series is based on Mark Yao's branch:
https://github.com/markyzq/kernel-drm-rockchip/tree/drm-rockchip-next-2016-05-23

I test this patches on the rk3399-evb board, with a fusb302 driver,
this branch has no rk3399.dtsi, so the patch about dts is not included
in this series.


Changes in v3:
- use compatible: rockchip,rk3399-typec-phy
- use dashes instead of underscores.
- remove the phy framework(Kishon Vijay Abraham I)
- add parentheses around the macro
- use a single space between type and name
- add spaces after opening and before closing braces.
- use u16 for register value
- remove type-c phy header file
- CodingStyle optimization
- use some cable extcon to get type-c port information
- add a extcon to notify Display Port
- add SoC specific compatible string
- remove reg = <1>;
- use EXTCON_DISP_DP and EXTCON_DISP_DP_ALT cable to get dp port state.
- reset spdif before config it
- modify the firmware clk to 100Mhz
- retry load firmware if fw file is requested too early

Changes in v2:
- add some registers description
- select RESET_CONTROLLER
- alphabetic order
- modify some spelling mistakes
- make mode cleaner
- use bool for enable/disable
- check all of the return value
- return a better err number
- use more readx_poll_timeout()
- clk_disable_unprepare(tcphy->clk_ref);
- remove unuse functions, rockchip_typec_phy_power_on/off
- remove unnecessary typecast from void *
- use dts node to distinguish between phys.
- Alphabetic order
- remove excess error message
- use define clk_rate
- check all return value
- remove dev_set_name(dp->dev, "cdn-dp");
- use schedule_delayed_work
- remove never-called functions
- remove some unnecessary ()

Changes in v1:
- add extcon node description
- move the registers in phy driver
- remove the suffix of reset
- update the licence note
- init core clock to 50MHz
- use extcon API
- remove unused global
- add some comments for magic num
- change usleep_range(1000, 2000) tousleep_range(1000, 1050)
- remove __func__ from dev_err
- return err number when get clk failed
- remove ADDR_ADJ define
- use devm_clk_get(&pdev->dev, "tcpdcore")
- add extcon node description
- add #sound-dai-cells description
- use extcon API
- use hdmi-codec for the DP Asoc
- do not initialize the "ret"
- printk a err log when drm_of_encoder_active_endpoint_id
- modify the dclk pin_pol to a single line

Chris Zhong (5):
  extcon: Add Type-C and DP support
  Documentation: bindings: add dt doc for Rockchip USB Type-C PHY
  phy: Add USB Type-C PHY driver for rk3399
  Documentation: bindings: add dt documentation for cdn DP controller
  drm/rockchip: cdn-dp: add cdn DP support for rk3399

 .../bindings/display/rockchip/cdn-dp-rockchip.txt  |   61 ++
 .../devicetree/bindings/phy/phy-rockchip-typec.txt |   74 ++
 drivers/extcon/extcon.c                            |    6 +
 drivers/gpu/drm/rockchip/Kconfig                   |    9 +
 drivers/gpu/drm/rockchip/Makefile                  |    1 +
 drivers/gpu/drm/rockchip/cdn-dp-core.c             |  722 ++++++++++++++
 drivers/gpu/drm/rockchip/cdn-dp-core.h             |  108 ++
 drivers/gpu/drm/rockchip/cdn-dp-reg.c              |  731 ++++++++++++++
 drivers/gpu/drm/rockchip/cdn-dp-reg.h              |  404 ++++++++
 drivers/gpu/drm/rockchip/rockchip_drm_vop.c        |    6 +-
 drivers/gpu/drm/rockchip/rockchip_drm_vop.h        |    2 +
 drivers/gpu/drm/rockchip/rockchip_vop_reg.c        |    2 +
 drivers/phy/Kconfig                                |    8 +
 drivers/phy/Makefile                               |    1 +
 drivers/phy/phy-rockchip-typec.c                   | 1027 ++++++++++++++++++++
 include/linux/extcon.h                             |    6 +
 16 files changed, 3167 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/display/rockchip/cdn-dp-rockchip.txt
 create mode 100644 Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
 create mode 100644 drivers/gpu/drm/rockchip/cdn-dp-core.c
 create mode 100644 drivers/gpu/drm/rockchip/cdn-dp-core.h
 create mode 100644 drivers/gpu/drm/rockchip/cdn-dp-reg.c
 create mode 100644 drivers/gpu/drm/rockchip/cdn-dp-reg.h
 create mode 100644 drivers/phy/phy-rockchip-typec.c

-- 
2.6.3

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

[v3 PATCH 2/5] Documentation: bindings: add dt doc for Rockchip USB Type-C PHY

[Chris Zhong]

This patch adds a binding that describes the Rockchip USB Type-C PHY
for rk3399

Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>

---

Changes in v3:
- use compatible: rockchip,rk3399-typec-phy
- use dashes instead of underscores.

Changes in v2:
- add some registers description

Changes in v1:
- add extcon node description
- move the registers in phy driver
- remove the suffix of reset

 .../devicetree/bindings/phy/phy-rockchip-typec.txt | 74 ++++++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt

diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
new file mode 100644
index 0000000..0c5b333
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
@@ -0,0 +1,74 @@
+* ROCKCHIP type-c PHY
+---------------------
+
+Required properties:
+ - compatible : must be "rockchip,rk3399-typec-phy"
+ - reg: Address and length of the usb phy control register set
+ - rockchip,grf : phandle to the syscon managing the "general
+   register files"
+ - clocks : phandle + clock specifier for the phy clocks
+ - clock-names : string, clock name, must be "tcpdcore", "tcpdphy-ref";
+ - resets : a list of phandle + reset specifier pairs
+ - reset-names : string reset name, must be:
+		 "uphy", "uphy-pipe", "uphy-tcphy"
+ - extcon : extcon specifier for the Power Delivery
+
+Note, there are 2 type-c phys for RK3399, and they are almost identical, except
+these registers(description below), every register node contains 3 sections:
+offset, enable bit, write mask bit.
+ - rockchip,typec-conn-dir : the register of type-c connector direction,
+   for type-c phy0, it must be <0xe580 0 16>;
+   for type-c phy1, it must be <0xe58c 0 16>;
+ - rockchip,usb3tousb2-en : the register of type-c force usb3 to usb2 enable
+   control.
+   for type-c phy0, it must be <0xe580 3 19>;
+   for type-c phy1, it must be <0xe58c 3 19>;
+ - rockchip,external-psm : the register of type-c phy external psm clock
+   selection.
+   for type-c phy0, it must be <0xe588 14 30>;
+   for type-c phy1, it must be <0xe594 14 30>;
+ - rockchip,pipe-status : the register of type-c phy pipe status.
+   for type-c phy0, it must be <0xe5c0 0 0>;
+   for type-c phy1, it must be <0xe5c0 16 16>;
+ - rockchip,uphy-dp-sel : the register of type-c phy selection for DP
+   for type-c phy0, it must be <0x6268 19 19>;
+   for type-c phy1, it must be <0x6268 3 19>;
+
+Example:
+	tcphy0: phy@ff7c0000 {
+		compatible = "rockchip,rk3399-typec-phy";
+		reg = <0x0 0xff7c0000 0x0 0x40000>;
+		extcon = <&fusb0>;
+		rockchip,grf = <&grf>;
+		clocks = <&cru SCLK_UPHY0_TCPDCORE>,
+			 <&cru SCLK_UPHY0_TCPDPHY_REF>;
+		clock-names = "tcpdcore", "tcpdphy-ref";
+		resets = <&cru SRST_UPHY0>,
+			 <&cru SRST_UPHY0_PIPE_L00>,
+			 <&cru SRST_P_UPHY0_TCPHY>;
+		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+		rockchip,typec-conn-dir = <0xe580 0 16>;
+		rockchip,usb3tousb2-en = <0xe580 3 19>;
+		rockchip,external-psm = <0xe588 14 30>;
+		rockchip,pipe-status = <0xe5c0 0 0>;
+		rockchip,uphy-dp-sel = <0x6268 19 19>;
+	};
+
+	tcphy1: phy@ff800000 {
+		compatible = "rockchip,rk3399-typec-phy";
+		reg = <0x0 0xff800000 0x0 0x40000>;
+		extcon = <&fusb1>;
+		rockchip,grf = <&grf>;
+		clocks = <&cru SCLK_UPHY1_TCPDCORE>,
+			 <&cru SCLK_UPHY1_TCPDPHY_REF>;
+		clock-names = "tcpdcore", "tcpdphy-ref";
+		resets = <&cru SRST_UPHY1>,
+		         <&cru SRST_UPHY1_PIPE_L00>,
+			 <&cru SRST_P_UPHY1_TCPHY>;
+		reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+		rockchip,typec-conn-dir = <0xe58c 0 16>;
+		rockchip,usb3tousb2-en = <0xe58c 3 19>;
+		rockchip,external-psm = <0xe594 14 30>;
+		rockchip,pipe-status = <0xe5c0 16 16>;
+		rockchip,uphy-dp-sel = <0x6268 3 19>;
+	};
-- 
2.6.3

Re: [v3 PATCH 2/5] Documentation: bindings: add dt doc for Rockchip USB Type-C PHY

[Rob Herring]

On Thu, Jun 23, 2016 at 08:51:01PM +0800, Chris Zhong wrote:
> This patch adds a binding that describes the Rockchip USB Type-C PHY
> for rk3399
> 
> Signed-off-by: Chris Zhong <zyw-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> Reviewed-by: Tomasz Figa <tfiga-F7+t8E8rja9g9hUCZPvPmw@public.gmane.org>
> Reviewed-by: Kever Yang <kever.yang-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
> 
> ---
> 
> Changes in v3:
> - use compatible: rockchip,rk3399-typec-phy
> - use dashes instead of underscores.
> 
> Changes in v2:
> - add some registers description
> 
> Changes in v1:
> - add extcon node description
> - move the registers in phy driver
> - remove the suffix of reset
> 
>  .../devicetree/bindings/phy/phy-rockchip-typec.txt | 74 ++++++++++++++++++++++
>  1 file changed, 74 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt

Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>

[v3 PATCH 4/5] Documentation: bindings: add dt documentation for cdn DP controller

[Chris Zhong]

This patch adds a binding that describes the cdn DP controller for
rk3399.

Signed-off-by: Chris Zhong <zyw@rock-chips.com>

---

Changes in v3:
- add SoC specific compatible string
- remove reg = <1>;

Changes in v2: None
Changes in v1:
- add extcon node description
- add #sound-dai-cells description

 .../bindings/display/rockchip/cdn-dp-rockchip.txt  | 61 ++++++++++++++++++++++
 1 file changed, 61 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/display/rockchip/cdn-dp-rockchip.txt

diff --git a/Documentation/devicetree/bindings/display/rockchip/cdn-dp-rockchip.txt b/Documentation/devicetree/bindings/display/rockchip/cdn-dp-rockchip.txt
new file mode 100644
index 0000000..b14b2b2
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/rockchip/cdn-dp-rockchip.txt
@@ -0,0 +1,61 @@
+Rockchip RK3399 specific extensions to the cdn Display Port
+================================
+
+Required properties:
+- compatible: must be "rockchip,rk3399-cdn-dp"
+
+- reg: physical base address of the controller and length
+
+- clocks: from common clock binding: handle to dp clock.
+
+- clock-names: from common clock binding:
+	       Required elements: "core-clk" "pclk" "spdif"
+
+- rockchip,grf: this soc should set GRF regs, so need get grf here.
+
+- ports: contain a port nodes with endpoint definitions as defined in
+	 Documentation/devicetree/bindings/media/video-interfaces.txt.
+	 contained 2 endpoints, connecting to the output of vop.
+
+- phys: from general PHY binding: the phandle for the PHY device.
+
+- extcon: extcon specifier for the Power Delivery
+
+- #sound-dai-cells = it must be 1 if your system is using 2 DAIs: I2S, SPDIF
+
+-------------------------------------------------------------------------------
+
+Example:
+	cdn_dp: dp@fec00000 {
+		compatible = "rockchip,rk3399-cdn-dp";
+		reg = <0x0 0xfec00000 0x0 0x100000>;
+		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+		clocks = <&cru SCLK_DP_CORE>, <&cru PCLK_DP_CTRL>,
+			 <&cru SCLK_SPDIF_REC_DPTX>;
+		clock-names = "core-clk", "pclk", "spdif";
+		phys = <&tcphy0>;
+		extcon = <&fusb1>;
+		rockchip,grf = <&grf>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		#sound-dai-cells = <1>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			dp_in: port {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				dp_in_vopb: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&vopb_out_dp>;
+				};
+
+				dp_in_vopl: endpoint@1 {
+					reg = <1>;
+					remote-endpoint = <&vopl_out_dp>;
+				};
+			};
+		};
+	};
-- 
2.6.3

_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel

Re: [v3 PATCH 4/5] Documentation: bindings: add dt documentation for cdn DP controller

[Rob Herring]

On Thu, Jun 23, 2016 at 08:51:03PM +0800, Chris Zhong wrote:
> This patch adds a binding that describes the cdn DP controller for
> rk3399.
> 
> Signed-off-by: Chris Zhong <zyw@rock-chips.com>
> 
> ---
> 
> Changes in v3:
> - add SoC specific compatible string
> - remove reg = <1>;
> 
> Changes in v2: None
> Changes in v1:
> - add extcon node description
> - add #sound-dai-cells description
> 
>  .../bindings/display/rockchip/cdn-dp-rockchip.txt  | 61 ++++++++++++++++++++++
>  1 file changed, 61 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/display/rockchip/cdn-dp-rockchip.txt

Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
dri-devel mailing list
dri-devel@lists.freedesktop.org
https://lists.freedesktop.org/mailman/listinfo/dri-devel