[PATCH v3 0/2] USB: xhci: add support for PWRON polarity invert (TI TUSB73x0)

[PATCH v3 0/2] USB: xhci: add support for PWRON polarity invert (TI TUSB73x0)

[Francesco Dolcini]

From: Francesco Dolcini <francesco.dolcini@toradex.com>

The TUSB73x0 is a USB 3.0 xHCI Host Controller Hub using a PCIe x1 Gen2
interface. The TUSB7320 supports up to two downstream ports, and the
TUSB7340 supports up to four. It includes a feature to configure the
polarity of the PWRONx# signals, which are used to control other peripherals.
In some systems, the default polarity needs to be inverted, which is
supported by the hardware through software configuration. This patch
series introduces TUSB73x0 PCIe device tree bindings and modifies the
USB XHCI PCI driver to handle PWRONx# polarity via a device tree property.

TUSB73x0 datasheet: https://www.ti.com/lit/ds/symlink/tusb7320.pdf

v3:
 - Correct the compatible string as "pci104c,8241" (uppercase hex to lowercase)

v2: https://lore.kernel.org/all/20241007093205.27130-1-francesco@dolcini.it/
 - Change the property type from bool to flag
 - Rename the property as ti,tusb7320-pwron-active-high

v1: https://lore.kernel.org/all/20241004124521.53442-1-francesco@dolcini.it/

Parth Pancholi (2):
  dt-bindings: usb: add TUSB73x0 PCIe
  USB: xhci: add support for PWRON active high

 .../bindings/usb/ti,tusb73x0-pci.yaml         | 60 +++++++++++++++++++
 drivers/usb/host/xhci-pci.c                   |  3 +
 2 files changed, 63 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml

-- 
2.39.5

[PATCH v3 1/2] dt-bindings: usb: add TUSB73x0 PCIe

[Francesco Dolcini]

From: Parth Pancholi <parth.pancholi@toradex.com>

Add device tree bindings for TI's TUSB73x0 PCIe-to-USB 3.0 xHCI
host controller. The controller supports software configuration
through PCIe registers, such as controlling the PWRONx polarity
via the USB control register (E0h).

Similar generic PCIe-based bindings can be found as qcom,ath11k-pci.yaml
as an example.

Datasheet: https://www.ti.com/lit/ds/symlink/tusb7320.pdf
Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
---
v3: use lowercase hex in compatible
v2: rename property to ti,tusb7320-pwron-active-high and change type to flag
---
 .../bindings/usb/ti,tusb73x0-pci.yaml         | 60 +++++++++++++++++++
 1 file changed, 60 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml

diff --git a/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml b/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml
new file mode 100644
index 000000000000..7083e24d279c
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml
@@ -0,0 +1,60 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/usb/ti,tusb73x0-pci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: TUSB73x0 USB 3.0 xHCI Host Controller (PCIe)
+
+maintainers:
+  - Francesco Dolcini <francesco.dolcini@toradex.com>
+
+description:
+  TUSB73x0 USB 3.0 xHCI Host Controller via PCIe x1 Gen2 interface.
+  The TUSB7320 supports up to two downstream ports, the TUSB7340 supports up
+  to four downstream ports.
+
+properties:
+  compatible:
+    const: pci104c,8241
+
+  reg:
+    maxItems: 1
+
+  ti,tusb7320-pwron-active-high:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Configure the polarity of the PWRONx# signals. When this is present, the PWRONx#
+      pins are active high and their internal pull-down resistors are disabled.
+      When this is absent, the PWRONx# pins are active low (default) and their internal
+      pull-down resistors are enabled.
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    pcie {
+        #address-cells = <3>;
+        #size-cells = <2>;
+
+        pcie@0 {
+            device_type = "pci";
+            reg = <0x0 0x0 0x0 0x0 0x0>;
+            bus-range = <0x01 0xff>;
+
+            #address-cells = <3>;
+            #size-cells = <2>;
+            ranges;
+
+            usb@0 {
+                  compatible = "pci104c,8241";
+                  reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+                  ti,tusb7320-pwron-active-high;
+            };
+        };
+    };
-- 
2.39.5

Re: [PATCH v3 1/2] dt-bindings: usb: add TUSB73x0 PCIe

[Rob Herring]

On Fri, Oct 18, 2024 at 12:55:04PM +0200, Francesco Dolcini wrote:
> From: Parth Pancholi <parth.pancholi@toradex.com>
> 
> Add device tree bindings for TI's TUSB73x0 PCIe-to-USB 3.0 xHCI
> host controller. The controller supports software configuration
> through PCIe registers, such as controlling the PWRONx polarity
> via the USB control register (E0h).
> 
> Similar generic PCIe-based bindings can be found as qcom,ath11k-pci.yaml
> as an example.
> 
> Datasheet: https://www.ti.com/lit/ds/symlink/tusb7320.pdf
> Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
> Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
> ---
> v3: use lowercase hex in compatible
> v2: rename property to ti,tusb7320-pwron-active-high and change type to flag
> ---
>  .../bindings/usb/ti,tusb73x0-pci.yaml         | 60 +++++++++++++++++++
>  1 file changed, 60 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml
> 
> diff --git a/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml b/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml
> new file mode 100644
> index 000000000000..7083e24d279c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml
> @@ -0,0 +1,60 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/usb/ti,tusb73x0-pci.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: TUSB73x0 USB 3.0 xHCI Host Controller (PCIe)
> +
> +maintainers:
> +  - Francesco Dolcini <francesco.dolcini@toradex.com>
> +
> +description:
> +  TUSB73x0 USB 3.0 xHCI Host Controller via PCIe x1 Gen2 interface.
> +  The TUSB7320 supports up to two downstream ports, the TUSB7340 supports up
> +  to four downstream ports.

XHCI controller, should be referencing usb-xhci.yaml.

> +
> +properties:
> +  compatible:
> +    const: pci104c,8241

2 parts mentioned above, but only 1 PCI ID?

> +
> +  reg:
> +    maxItems: 1
> +
> +  ti,tusb7320-pwron-active-high:

Drop 'tusb7320-'

> +    $ref: /schemas/types.yaml#/definitions/flag
> +    description:
> +      Configure the polarity of the PWRONx# signals. When this is present, the PWRONx#
> +      pins are active high and their internal pull-down resistors are disabled.
> +      When this is absent, the PWRONx# pins are active low (default) and their internal
> +      pull-down resistors are enabled.
> +
> +required:
> +  - compatible
> +  - reg
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    pcie {
> +        #address-cells = <3>;
> +        #size-cells = <2>;
> +
> +        pcie@0 {
> +            device_type = "pci";

You can move this up a level and get rid of this middle node. 

> +            reg = <0x0 0x0 0x0 0x0 0x0>;
> +            bus-range = <0x01 0xff>;

Not needed for examples.

> +
> +            #address-cells = <3>;
> +            #size-cells = <2>;
> +            ranges;
> +
> +            usb@0 {
> +                  compatible = "pci104c,8241";
> +                  reg = <0x10000 0x0 0x0 0x0 0x0>;

In FDT, we generally don't know the bus number because the OS assigns 
them. So it should always be 0 in 'reg'.

Rob

Re: [PATCH v3 1/2] dt-bindings: usb: add TUSB73x0 PCIe

[Francesco Dolcini]

Hello Rob,
thanks for the review.

On Fri, Oct 18, 2024 at 09:07:43AM -0500, Rob Herring wrote:
> On Fri, Oct 18, 2024 at 12:55:04PM +0200, Francesco Dolcini wrote:
> > From: Parth Pancholi <parth.pancholi@toradex.com>
> > 
> > Add device tree bindings for TI's TUSB73x0 PCIe-to-USB 3.0 xHCI
> > host controller. The controller supports software configuration
> > through PCIe registers, such as controlling the PWRONx polarity
> > via the USB control register (E0h).
> > 
> > Similar generic PCIe-based bindings can be found as qcom,ath11k-pci.yaml
> > as an example.
> > 
> > Datasheet: https://www.ti.com/lit/ds/symlink/tusb7320.pdf
> > Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
> > Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
> > ---
> > v3: use lowercase hex in compatible
> > v2: rename property to ti,tusb7320-pwron-active-high and change type to flag
> > ---
> >  .../bindings/usb/ti,tusb73x0-pci.yaml         | 60 +++++++++++++++++++
> >  1 file changed, 60 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml b/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml
> > new file mode 100644
> > index 000000000000..7083e24d279c
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/usb/ti,tusb73x0-pci.yaml
> > @@ -0,0 +1,60 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/usb/ti,tusb73x0-pci.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: TUSB73x0 USB 3.0 xHCI Host Controller (PCIe)
> > +
> > +maintainers:
> > +  - Francesco Dolcini <francesco.dolcini@toradex.com>
> > +
> > +description:
> > +  TUSB73x0 USB 3.0 xHCI Host Controller via PCIe x1 Gen2 interface.
> > +  The TUSB7320 supports up to two downstream ports, the TUSB7340 supports up
> > +  to four downstream ports.
> 
> XHCI controller, should be referencing usb-xhci.yaml.
> 
> > +
> > +properties:
> > +  compatible:
> > +    const: pci104c,8241
> 
> 2 parts mentioned above, but only 1 PCI ID?

Exactly. Let me know if there is something we should do in this regard
(something in the commit message? or in the description?).

From the datasheet:
  This 16-bit read only register contains the value 8241h,
  which is the device ID assigned by TI to the TUSB73X0

And one more confirmation, in the Linux code you have quirks for this
device that just check for a single device id:

drivers/usb/host/xhci-pci.c:459
  if (pdev->vendor == PCI_VENDOR_ID_TI && pdev->device == 0x8241)         
    xhci->quirks |= XHCI_LIMIT_ENDPOINT_INTERVAL_7;                 

Francesco

[PATCH v3 2/2] USB: xhci: add support for PWRON active high

[Francesco Dolcini]

From: Parth Pancholi <parth.pancholi@toradex.com>

Some PCIe-to-USB controllers such as TI's TUSB73x0 3.0 xHCI host
controller supports controlling the PWRONx polarity via the USB
control register (E0h). Add support for device tree property
ti,tusb7320-pwron-active-high which indicates PWRONx to be
active high and configure the E0h register accordingly.
This enables the software control for the TUSB73x0's PWRONx
outputs with an inverted polarity from the default configuration
which could be used as USB EN signals for the other hubs or devices.

Signed-off-by: Parth Pancholi <parth.pancholi@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
---
v3: no changes
v2: s/polarity-invert/active-high
---
 drivers/usb/host/xhci-pci.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/usb/host/xhci-pci.c b/drivers/usb/host/xhci-pci.c
index 91dccd25a551..4bdef01735eb 100644
--- a/drivers/usb/host/xhci-pci.c
+++ b/drivers/usb/host/xhci-pci.c
@@ -641,6 +641,9 @@ int xhci_pci_common_probe(struct pci_dev *dev, const struct pci_device_id *id)
 
 	dma_set_max_seg_size(&dev->dev, UINT_MAX);
 
+	if (device_property_read_bool(&dev->dev, "ti,tusb7320-pwron-active-high"))
+		pci_clear_and_set_config_dword(dev, 0xE0, 0, 1 << 22);
+
 	return 0;
 
 put_usb3_hcd:
-- 
2.39.5