[PATCH v2 2/2] ARM: dts: omap4: panda: cleanup bluetooth

[Andreas Kemnade <andreas@kemnade.info>]

Bluetooth is available on the other Panda board versions, too, so move
stuff to common and specify the needed clock properly.

Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
---
 .../boot/dts/ti/omap/omap4-panda-common.dtsi  | 31 ++++++++++++++++--
 arch/arm/boot/dts/ti/omap/omap4-panda-es.dts  | 32 -------------------
 2 files changed, 28 insertions(+), 35 deletions(-)

diff --git a/arch/arm/boot/dts/ti/omap/omap4-panda-common.dtsi b/arch/arm/boot/dts/ti/omap/omap4-panda-common.dtsi
index c860b590142a..05c871d31d7b 100644
--- a/arch/arm/boot/dts/ti/omap/omap4-panda-common.dtsi
+++ b/arch/arm/boot/dts/ti/omap/omap4-panda-common.dtsi
@@ -367,10 +367,8 @@ OMAP4_IOPAD(0x130, PIN_INPUT_PULLUP | MUX_MODE0)	/* i2c4_sda */
 	 */
 	wl12xx_gpio: wl12xx-gpio-pins {
 		pinctrl-single,pins = <
-			OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a19.gpio_43 */
-			OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a22.gpio_46 */
+			OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a19.gpio_43 - WLAN_EN */
 			OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLUP | MUX_MODE3)	/* gpmc_a24.gpio_48 */
-			OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3)	/* gpmc_a25.gpio_49 */
 		>;
 	};
 
@@ -393,6 +391,22 @@ button_pins: button-pins {
 			OMAP4_IOPAD(0x114, PIN_INPUT_PULLUP | MUX_MODE3)	/* gpio_121 */
 		>;
 	};
+
+	bt_pins: bt-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3)	  /* gpmc_a22.gpio_46 - BTEN */
+			OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3) /* gpmc_a25.gpio_49 - BTWAKEUP */
+		>;
+	};
+
+	uart2_pins: uart2-pins {
+		pinctrl-single,pins = <
+			OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0)  /* uart2_cts.uart2_cts - HCI */
+			OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0)	  /* uart2_rts.uart2_rts */
+			OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0)  /* uart2_rx.uart2_rx */
+			OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0)	  /* uart2_tx.uart2_tx */
+		>;
+	};
 };
 
 &omap4_pmx_wkup {
@@ -531,8 +545,19 @@ &twl_usb_comparator {
 };
 
 &uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart2_pins>;
 	interrupts-extended = <&wakeupgen GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH
 			       &omap4_pmx_core OMAP4_UART2_RX>;
+
+	bluetooth {
+		compatible = "ti,wl1271-st";
+		pinctrl-names = "default";
+		pinctrl-0 = <&bt_pins>;
+		enable-gpios = <&gpio2 14 GPIO_ACTIVE_HIGH>;	/* GPIO_46 */
+		clocks = <&twl 0>;
+		clock-names = "ext_clock";
+	};
 };
 
 &uart3 {
diff --git a/arch/arm/boot/dts/ti/omap/omap4-panda-es.dts b/arch/arm/boot/dts/ti/omap/omap4-panda-es.dts
index fe7b156d10ed..a933fe560834 100644
--- a/arch/arm/boot/dts/ti/omap/omap4-panda-es.dts
+++ b/arch/arm/boot/dts/ti/omap/omap4-panda-es.dts
@@ -49,22 +49,6 @@ button_pins: button-pins {
 			OMAP4_IOPAD(0x0fc, PIN_INPUT_PULLUP | MUX_MODE3) /* gpio_113 */
 		>;
 	};
-
-	bt_pins: bt-pins {
-		pinctrl-single,pins = <
-			OMAP4_IOPAD(0x06c, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a22.gpio_46 - BTEN */
-			OMAP4_IOPAD(0x072, PIN_OUTPUT_PULLUP | MUX_MODE3)	/* gpmc_a25.gpio_49 - BTWAKEUP */
-		>;
-	};
-
-	uart2_pins: uart2-pins {
-		pinctrl-single,pins = <
-			OMAP4_IOPAD(0x118, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_cts.uart2_cts - HCI */
-			OMAP4_IOPAD(0x11a, PIN_OUTPUT | MUX_MODE0)		/* uart2_rts.uart2_rts */
-			OMAP4_IOPAD(0x11c, PIN_INPUT_PULLUP | MUX_MODE0)	/* uart2_rx.uart2_rx */
-			OMAP4_IOPAD(0x11e, PIN_OUTPUT | MUX_MODE0)		/* uart2_tx.uart2_tx */
-		>;
-	};
 };
 
 &led_wkgpio_pins {
@@ -96,19 +80,3 @@ buttonS2 {
 &gpio1_target {
 	 ti,no-reset-on-init;
 };
-
-&wl12xx_gpio {
-	pinctrl-single,pins = <
-		OMAP4_IOPAD(0x066, PIN_OUTPUT | MUX_MODE3)		/* gpmc_a19.gpio_43 */
-		OMAP4_IOPAD(0x070, PIN_OUTPUT_PULLUP | MUX_MODE3)	/* gpmc_a24.gpio_48 */
-	>;
-};
-
-&uart2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart2_pins &bt_pins>;
-	bluetooth: tiwi {
-		compatible = "ti,wl1271-st";
-		enable-gpios = <&gpio2 14 GPIO_ACTIVE_HIGH>;	/* GPIO_46 */
-	};
-};
-- 
2.39.5