[PATCH 00/12] ARM: bcm: Add some BCMBCA peripherals

[PATCH 00/12] ARM: bcm: Add some BCMBCA peripherals

[Linus Walleij]

This adds a bunch peripherals to the Broadcom BRCMBCA
SoC:s that I happened to find documentation for in some
vendor header files.

It started when I added a bunch of peripherals for the
BCM6846, and this included really helpful peripherals
such as the PL081 DMA, for which I think the most common
usecase is to be used as a memcpy engine to offload
transfer of blocks from NAND flash to/from the NAND
flash controller (at least this is how the STMicro
FSMC controller was using it).

So I took a sweep and added all the stuff that has
bindings to:

ARM:
- BCM6846
- BCM6855
- BCM6878
- BCM63138
- BCM63148
- BCM63178

ARM64:
- BCM4908
- BCM6856
- BCM6858
- BCM63158

There are several "holes" in this SoC list, I simply
just fixed those that I happened to run into documentation
for.

Unfortunately while very similar, some IP blocks vary
slightly in version, the GPIO block is differently
integrated on different systems, and the interrupt assignments
are completely different, so it's safest to add these to each
DTSI individually.

I add the interrupt binding for the RNG block in the
process as this exists even if Linux isn't using the
IRQ, and I put the RNG and DMA engines as default-enabled
because they are not routed to the outside and should
"just work" so why not.

I did a rogue patch adding some stuff to BCM6756 based
on guessed but eventually dropped it. If someone has
docs for this SoC I can add it.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
Linus Walleij (12):
      ARM: dts: bcm6878: Correct UART0 IRQ number
      dt-bindings: rng: r200: Add interrupt property
      ARM: dts: bcm6846: Add interrupt to RNG
      ARM: dts: bcm6855: Add BCMBCA peripherals
      ARM: dts: bcm6878: Add BCMBCA peripherals
      ARM: dts: bcm63138: Add BCMBCA peripherals
      ARM: dts: bcm63148: Add BCMBCA peripherals
      ARM: dts: bcm63178: Add BCMBCA peripherals
      ARM64: dts: bcm4908: Add BCMBCA peripherals
      ARM64: dts: bcm6856: Add BCMBCA peripherals
      ARM64: dts: bcm6858: Add BCMBCA peripherals
      ARM64: dts: bcm63158: Add BCMBCA peripherals

 .../devicetree/bindings/rng/brcm,iproc-rng200.yaml |   6 +
 arch/arm/boot/dts/broadcom/bcm63138.dtsi           |  79 ++++++++++-
 arch/arm/boot/dts/broadcom/bcm63148.dtsi           |  64 +++++++++
 arch/arm/boot/dts/broadcom/bcm63178.dtsi           | 112 +++++++++++++++
 arch/arm/boot/dts/broadcom/bcm6846.dtsi            |   1 +
 arch/arm/boot/dts/broadcom/bcm6855.dtsi            | 127 +++++++++++++++++
 arch/arm/boot/dts/broadcom/bcm6878.dtsi            | 120 ++++++++++++++++-
 arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi   | 122 ++++++++++++++++-
 arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi  | 150 ++++++++++++++++++++-
 arch/arm64/boot/dts/broadcom/bcmbca/bcm6856.dtsi   | 138 ++++++++++++++++++-
 arch/arm64/boot/dts/broadcom/bcmbca/bcm6858.dtsi   | 120 ++++++++++++++++-
 11 files changed, 1030 insertions(+), 9 deletions(-)
---
base-commit: 8359b1e7edc722d4b1be26aa515041a79e4224a3
change-id: 20250327-bcmbca-peripherals-arm-dfb312052363

Best regards,
-- 
Linus Walleij <linus.walleij@linaro.org>

[PATCH 01/12] ARM: dts: bcm6878: Correct UART0 IRQ number

[Linus Walleij]

According to the vendor file 6878_intr.h the UART0 has IRQ
28, not 32.

Assuming this is a copy-and-paste error.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/broadcom/bcm6878.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/broadcom/bcm6878.dtsi b/arch/arm/boot/dts/broadcom/bcm6878.dtsi
index 70cf23a65fdb5ac7ed9eabc986f4ebb4df263c43..cf378970db08c05c40564a38931417a7be759532 100644
--- a/arch/arm/boot/dts/broadcom/bcm6878.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm6878.dtsi
@@ -137,7 +137,7 @@ nandcs: nand@0 {
 		uart0: serial@12000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x12000 0x1000>;
-			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&uart_clk>, <&uart_clk>;
 			clock-names = "uartclk", "apb_pclk";
 			status = "disabled";

-- 
2.48.1

[PATCH 02/12] dt-bindings: rng: r200: Add interrupt property

[Linus Walleij]

This IP block has an interrupt. Add it and add it to the
example as well.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 Documentation/devicetree/bindings/rng/brcm,iproc-rng200.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.yaml b/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.yaml
index 827983008ecf707019f45847cd86d5686e3b2469..817cbdaa2b2d75705eda212521186c40a9975ea0 100644
--- a/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.yaml
+++ b/Documentation/devicetree/bindings/rng/brcm,iproc-rng200.yaml
@@ -20,11 +20,17 @@ properties:
   reg:
     maxItems: 1
 
+  interrupts:
+    maxItems: 1
+
 additionalProperties: false
 
 examples:
   - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
     rng@18032000 {
         compatible = "brcm,iproc-rng200";
         reg = <0x18032000 0x28>;
+        interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
     };

-- 
2.48.1

[PATCH 03/12] ARM: dts: bcm6846: Add interrupt to RNG

[Linus Walleij]

The r200 RNG has an interrupt so let's add it.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/broadcom/bcm6846.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/broadcom/bcm6846.dtsi b/arch/arm/boot/dts/broadcom/bcm6846.dtsi
index e0e06af3fe891df3c3d8c2005cf1980d33a7762b..d36d0a791dbf4ca3442797691957c3247c7187e7 100644
--- a/arch/arm/boot/dts/broadcom/bcm6846.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm6846.dtsi
@@ -196,6 +196,7 @@ uart0: serial@640 {
 		rng@b80 {
 			compatible = "brcm,iproc-rng200";
 			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
 		leds: led-controller@800 {

-- 
2.48.1

[PATCH 04/12] ARM: dts: bcm6855: Add BCMBCA peripherals

[Linus Walleij]

All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments.

Add the first and second watchdog, GPIO, RNG, LED, DMA and
second PL011 UART blocks for the BCM6855 based on the vendor
files 6855_map_part.h and 6855_intr.h from the
"bcmopen-consumer" code drop.

This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/broadcom/bcm6855.dtsi | 127 ++++++++++++++++++++++++++++++++
 1 file changed, 127 insertions(+)

diff --git a/arch/arm/boot/dts/broadcom/bcm6855.dtsi b/arch/arm/boot/dts/broadcom/bcm6855.dtsi
index 52915ec6f339335d87b4e50e1c03625fffb9a45d..a88c3f0fbcb037ee5c6b31933415f90cb51ded2a 100644
--- a/arch/arm/boot/dts/broadcom/bcm6855.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm6855.dtsi
@@ -116,6 +116,103 @@ bus@ff800000 {
 		#size-cells = <1>;
 		ranges = <0 0xff800000 0x800000>;
 
+		watchdog@480 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x480 0x10>;
+		};
+
+		watchdog@4c0 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x4c0 0x10>;
+			status = "disabled";
+		};
+
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x528 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x52c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x530 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 160 .. 191 */
+		gpio5: gpio@514 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x514 0x04>, <0x534 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 192 .. 223 */
+		gpio6: gpio@518 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x518 0x04>, <0x538 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 224 .. 255 */
+		gpio7: gpio@51c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x51c 0x04>, <0x53c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		rng@b80 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		hsspi: spi@1000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -143,6 +240,27 @@ nandcs: nand@0 {
 			};
 		};
 
+		leds: led-controller@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x3000 0xdc>;
+			status = "disabled";
+		};
+
+		pl081_dma: dma-controller@11000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0x11000 0x1000>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+
 		uart0: serial@12000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x12000 0x1000>;
@@ -151,5 +269,14 @@ uart0: serial@12000 {
 			clock-names = "uartclk", "apb_pclk";
 			status = "disabled";
 		};
+
+		uart1: serial@13000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x13000 0x1000>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
 	};
 };

-- 
2.48.1

[PATCH 05/12] ARM: dts: bcm6878: Add BCMBCA peripherals

[Linus Walleij]

All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments.

Add the first and second watchdog, GPIO, RNG, LED and
DMA blocks for the BCM6878 based on the vendor files
6878_map_part.h and 6878_intr.h from the "bcmopen-consumer"
code drop.

This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/broadcom/bcm6878.dtsi | 118 ++++++++++++++++++++++++++++++++
 1 file changed, 118 insertions(+)

diff --git a/arch/arm/boot/dts/broadcom/bcm6878.dtsi b/arch/arm/boot/dts/broadcom/bcm6878.dtsi
index cf378970db08c05c40564a38931417a7be759532..f317fc888da0ef449d9b5153677e6dadd869a7db 100644
--- a/arch/arm/boot/dts/broadcom/bcm6878.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm6878.dtsi
@@ -108,6 +108,111 @@ bus@ff800000 {
 		#size-cells = <1>;
 		ranges = <0 0xff800000 0x800000>;
 
+		watchdog@480 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x480 0x10>;
+		};
+
+		watchdog@4c0 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x4c0 0x10>;
+			status = "disabled";
+		};
+
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x528 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x52c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x530 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 160 .. 191 */
+		gpio5: gpio@514 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x514 0x04>, <0x534 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 192 .. 223 */
+		gpio6: gpio@518 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x518 0x04>, <0x538 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 224 .. 255 */
+		gpio7: gpio@51c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x51c 0x04>, <0x53c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		rng@b80 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		leds: led-controller@700 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x700 0xdc>;
+			status = "disabled";
+		};
+
 		hsspi: spi@1000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -134,6 +239,19 @@ nandcs: nand@0 {
 			};
 		};
 
+		pl081_dma: dma-controller@11000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0x11000 0x1000>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+
 		uart0: serial@12000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x12000 0x1000>;

-- 
2.48.1

[PATCH 06/12] ARM: dts: bcm63138: Add BCMBCA peripherals

[Linus Walleij]

All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments.

Extend the peripheral interrupt window to 0x10000 as it need
to fit the DMA block.

Add the GPIO, RNG and LED and DMA blocks for the
BCM63138 based on the vendor files 63138_map_part.h and
63138_intr.h from the "bcmopen-consumer" code drop.

This SoC has up to 160 possible GPIOs due to having 5
registers with 32 GPIOs in each available.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/broadcom/bcm63138.dtsi | 79 +++++++++++++++++++++++++++++++-
 1 file changed, 78 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/broadcom/bcm63138.dtsi b/arch/arm/boot/dts/broadcom/bcm63138.dtsi
index e74ba6bf370da63d3c115e38b4f20c71baff2116..182394a96bd46eb0258ebfa6d5f00ea008aa671c 100644
--- a/arch/arm/boot/dts/broadcom/bcm63138.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm63138.dtsi
@@ -184,13 +184,69 @@ ubus@fffe8000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges = <0 0xfffe8000 0x8100>;
+		ranges = <0 0xfffe8000 0x10000>;
 
 		timer: timer@80 {
 			compatible = "brcm,bcm6328-timer", "syscon";
 			reg = <0x80 0x3c>;
 		};
 
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@100 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x514 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x518 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x51c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		rng@300 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0x300 0x28>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		serial0: serial@600 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x600 0x1b>;
@@ -209,6 +265,14 @@ serial1: serial@620 {
 			status = "disabled";
 		};
 
+		leds: led-controller@700 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x700 0xdc>;
+			status = "disabled";
+		};
+
 		hsspi: spi@1000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -248,6 +312,19 @@ bootlut: bootlut@8000 {
 			reg = <0x8000 0x50>;
 		};
 
+		pl081_dma: dma-controller@d000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0xd000 0x1000>;
+			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+
 		reboot {
 			compatible = "syscon-reboot";
 			regmap = <&timer>;

-- 
2.48.1

[PATCH 07/12] ARM: dts: bcm63148: Add BCMBCA peripherals

[Linus Walleij]

All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments.

Add the GPIO, RNG and LED and DMA blocks for the
BCM63148 based on the vendor files 63148_map_part.h and
63148_intr.h from the "bcmopen-consumer" code drop.

This SoC has up to 160 possible GPIOs due to having 5
registers with 32 GPIOs in each available.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/broadcom/bcm63148.dtsi | 64 ++++++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)

diff --git a/arch/arm/boot/dts/broadcom/bcm63148.dtsi b/arch/arm/boot/dts/broadcom/bcm63148.dtsi
index 53703827ee3fe58ead1dbe70536d7293ad842d0c..0f6232f0553ad62fbaa7d8db251a0204ed6ed782 100644
--- a/arch/arm/boot/dts/broadcom/bcm63148.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm63148.dtsi
@@ -99,6 +99,62 @@ bus@ff800000 {
 		#size-cells = <1>;
 		ranges = <0 0xfffe8000 0x8000>;
 
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@100 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x514 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x518 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x51c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		rng@300 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0x300 0x28>;
+			interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		uart0: serial@600 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x600 0x20>;
@@ -108,6 +164,14 @@ uart0: serial@600 {
 			status = "disabled";
 		};
 
+		leds: led-controller@700 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x700 0xdc>;
+			status = "disabled";
+		};
+
 		hsspi: spi@1000 {
 			#address-cells = <1>;
 			#size-cells = <0>;

-- 
2.48.1

[PATCH 08/12] ARM: dts: bcm63178: Add BCMBCA peripherals

[Linus Walleij]

All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments.

Add the watchdog, GPIO, RNG, LED and DMA blocks for the
BCM63178 based on the vendor files 63178_map_part.h and
63178_intr.h from the "bcmopen-consumer" code drop.

This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm/boot/dts/broadcom/bcm63178.dtsi | 112 +++++++++++++++++++++++++++++++
 1 file changed, 112 insertions(+)

diff --git a/arch/arm/boot/dts/broadcom/bcm63178.dtsi b/arch/arm/boot/dts/broadcom/bcm63178.dtsi
index 6d8d33498983acfc0c65ee155f64ddedc4a6b376..430750b3030f2534d6bf0468d895ca565007a53f 100644
--- a/arch/arm/boot/dts/broadcom/bcm63178.dtsi
+++ b/arch/arm/boot/dts/broadcom/bcm63178.dtsi
@@ -117,6 +117,97 @@ bus@ff800000 {
 		#size-cells = <1>;
 		ranges = <0 0xff800000 0x800000>;
 
+		watchdog@480 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x480 0x10>;
+		};
+
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x528 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x52c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x530 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 160 .. 191 */
+		gpio5: gpio@514 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x514 0x04>, <0x534 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 192 .. 223 */
+		gpio6: gpio@518 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x518 0x04>, <0x538 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 224 .. 255 */
+		gpio7: gpio@51c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x51c 0x04>, <0x53c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		rng@b80 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		hsspi: spi@1000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -143,6 +234,27 @@ nandcs: nand@0 {
 			};
 		};
 
+		leds: led-controller@3000 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x3000 0xdc>;
+			status = "disabled";
+		};
+
+		pl081_dma: dma-controller@11000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0x11000 0x1000>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+
 		uart0: serial@12000 {
 			compatible = "arm,pl011", "arm,primecell";
 			reg = <0x12000 0x1000>;

-- 
2.48.1

[PATCH 09/12] ARM64: dts: bcm4908: Add BCMBCA peripherals

[Linus Walleij]

All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments. ARM64 SoCs have additional
peripherals at 0xff858000.

Add the watchdog, remaining GPIO blocks, RNG, and DMA blocks
for the BCM4908 based on the vendor files 4908_map_part.h
and 4908_intr.h from the "bcmopen-consumer" code drop.

This SoC has up to 320 possible GPIOs due to having 10
registers with 32 GPIOs in each available.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi | 122 ++++++++++++++++++++++-
 1 file changed, 120 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi
index 613ba7ee43d6489ea0f1490d2fccaf90961b2694..a2e5277a2e77c0bdec5d933d3121b4ebf2d2d07b 100644
--- a/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm4908.dtsi
@@ -323,6 +323,7 @@ pmb: power-controller@2800c0 {
 		};
 	};
 
+	/* PERF Peripherals */
 	bus@ff800000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -348,13 +349,103 @@ watchdog@28 {
 			};
 		};
 
-		gpio0: gpio-controller@500 {
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@500 {
 			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x528 0x04>;
 			reg-names = "dirout", "dat";
-			reg = <0x500 0x28>, <0x528 0x28>;
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x52c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x530 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x534 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
 
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x538 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
 			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 160 .. 191 */
+		gpio5: gpio@514 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x514 0x04>, <0x53c 0x04>;
+			reg-names = "dirout", "dat";
 			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 192 .. 223 */
+		gpio6: gpio@518 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x518 0x04>, <0x540 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 224 .. 255 */
+		gpio7: gpio@51c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x51c 0x04>, <0x544 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 256 .. 287 */
+		gpio8: gpio@520 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x520 0x04>, <0x548 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 288 .. 319 */
+		gpio9: gpio@524 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x524 0x04>, <0x54c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
 		};
 
 		pinctrl@560 {
@@ -584,6 +675,12 @@ leds: leds@800 {
 			#size-cells = <0>;
 		};
 
+		rng@b80 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		hsspi: spi@1000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -638,6 +735,27 @@ reset-controller@2644 {
 		};
 	};
 
+	/* PERF1 Peripherals */
+	bus@ff858000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x00 0x00 0xff858000 0x3000>;
+
+		pl081_dma: dma-controller@1000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0x1000 0x1000>;
+			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+	};
+
 	reboot {
 		compatible = "syscon-reboot";
 		regmap = <&twd>;

-- 
2.48.1

[PATCH 10/12] ARM64: dts: bcm6856: Add BCMBCA peripherals

[Linus Walleij]

All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments. ARM64 SoCs have additional
peripherals at 0xff858000. On BCM6856 the PERF window was
too big so adjust it down to its real size (0x3000) and add
another window for PERF1 at 0xff858000.

Add the watchdog, GPIO blocks, RNG, LED, second UART and DMA
blocks for the BCM6856 based on the vendor files 6856_map_part.h
and 6856_intr.h from the "bcmopen-consumer" code drop.

This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm64/boot/dts/broadcom/bcmbca/bcm6856.dtsi | 138 ++++++++++++++++++++++-
 1 file changed, 137 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm6856.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm6856.dtsi
index 00c62c1e5df00c722884a7adfcb7be08a43c0dc3..d6d0b8e1a65b494be414dd5841b65f8ff489d684 100644
--- a/arch/arm64/boot/dts/broadcom/bcmbca/bcm6856.dtsi
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm6856.dtsi
@@ -93,11 +93,103 @@ gic: interrupt-controller@1000 {
 		};
 	};
 
+	/* PERF Peripherals */
 	bus@ff800000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges = <0x0 0x0 0xff800000 0x800000>;
+		ranges = <0x0 0x0 0xff800000 0x3000>;
+
+		watchdog@480 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x480 0x10>;
+		};
+
+		watchdog@4c0 {
+			compatible = "brcm,bcm6345-wdt";
+			reg = <0x4c0 0x10>;
+			status = "disabled";
+		};
+
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x528 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x52c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x530 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 160 .. 191 */
+		gpio5: gpio@514 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x514 0x04>, <0x534 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 192 .. 223 */
+		gpio6: gpio@518 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x518 0x04>, <0x538 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 224 .. 255 */
+		gpio7: gpio@51c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x51c 0x04>, <0x53c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
 
 		uart0: serial@640 {
 			compatible = "brcm,bcm6345-uart";
@@ -108,6 +200,29 @@ uart0: serial@640 {
 			status = "disabled";
 		};
 
+		uart1: serial@660 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x660 0x18>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+
+		leds: led-controller@800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x800 0xdc>;
+			status = "disabled";
+		};
+
+		rng@b80 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		hsspi: spi@1000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -134,4 +249,25 @@ nandcs: nand@0 {
 			};
 		};
 	};
+
+	/* PERF1 Peripherals */
+	bus@ff858000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff858000 0x4000>;
+
+		pl081_dma: dma-controller@1000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0x1000 0x1000>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+	};
 };

-- 
2.48.1

[PATCH 11/12] ARM64: dts: bcm6858: Add BCMBCA peripherals

[Linus Walleij]

All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments. ARM64 SoCs have additional
peripherals at 0xff858000. On BCM6858 the PERF window was
too big so adjust it down to its real size (0x3000).

Add the watchdog, GPIO blocks, RNG, LED, second UART and DMA
blocks for the BCM6858 based on the vendor files 6858_map_part.h
and 6858_intr.h from the "bcmopen-consumer" code drop.

Curiously, on the BCM6858, the PL081 DMA block is separate
from the two peripheral groups PERF and PERF1, so we put it
in a separate node in the device tree since this is what the
documentation says.

This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm64/boot/dts/broadcom/bcmbca/bcm6858.dtsi | 120 ++++++++++++++++++++++-
 1 file changed, 119 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm6858.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm6858.dtsi
index caeaf428dc15db3089bf4dc62c4a272782c22c3f..a53520ce693c7360c603e8f46cefe134a509d051 100644
--- a/arch/arm64/boot/dts/broadcom/bcmbca/bcm6858.dtsi
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm6858.dtsi
@@ -111,11 +111,12 @@ gic: interrupt-controller@1000 {
 		};
 	};
 
+	/* PERF Peripherals */
 	bus@ff800000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges = <0x0 0x0 0xff800000 0x62000>;
+		ranges = <0x0 0x0 0xff800000 0x3000>;
 
 		twd: timer-mfd@400 {
 			compatible = "brcm,bcm4908-twd", "simple-mfd", "syscon";
@@ -136,6 +137,86 @@ watchdog@28 {
 			};
 		};
 
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x528 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x52c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x530 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 160 .. 191 */
+		gpio5: gpio@514 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x514 0x04>, <0x534 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 192 .. 223 */
+		gpio6: gpio@518 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x518 0x04>, <0x538 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 224 .. 255 */
+		gpio7: gpio@51c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x51c 0x04>, <0x53c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
 		uart0: serial@640 {
 			compatible = "brcm,bcm6345-uart";
 			reg = <0x640 0x18>;
@@ -145,6 +226,29 @@ uart0: serial@640 {
 			status = "disabled";
 		};
 
+		uart1: serial@660 {
+			compatible = "brcm,bcm6345-uart";
+			reg = <0x660 0x18>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&periph_clk>;
+			clock-names = "refclk";
+			status = "disabled";
+		};
+
+		leds: led-controller@800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x800 0xdc>;
+			status = "disabled";
+		};
+
+		rng@b80 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
 		hsspi: spi@1000 {
 			#address-cells = <1>;
 			#size-cells = <0>;
@@ -171,4 +275,18 @@ nandcs: nand@0 {
 			};
 		};
 	};
+
+	/* This is NOT in the PERF1 Peripheral group on this SoC! */
+	pl081_dma: dma-controller@ff859000 {
+		compatible = "arm,pl081", "arm,primecell";
+		// The magic B105F00D info is missing
+		arm,primecell-periphid = <0x00041081>;
+		reg = <0xff859000 0x1000>;
+		interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+		memcpy-burst-size = <256>;
+		memcpy-bus-width = <32>;
+		clocks = <&periph_clk>;
+		clock-names = "apb_pclk";
+		#dma-cells = <2>;
+	};
 };

-- 
2.48.1

[PATCH 12/12] ARM64: dts: bcm63158: Add BCMBCA peripherals

[Linus Walleij]

All the BCMBCA SoCs share a set of peripherals at 0xff800000,
albeit at slightly varying memory locations on the bus and
with varying IRQ assignments. On BCM63158 the PERF window was
too big so adjust it down to its real size (0x3000).

Add the watchdog, GPIO blocks, RNG, LED, second UART and DMA
blocks for the BCM63158 based on the vendor files 63158_map_part.h
and 63158_intr.h from the "bcmopen-consumer" code drop.

The DTSI file has clearly been authored for the B0 revision of
the SoC: there is an earlier A0 version, but this has
the UARTs in the legacy PERF memory space, while the B0
has opened a new peripheral window at 0xff812000 for the
three UARTs. It also has a designated AHB peripheral area
at 0xff810000 where the DMA resides, so we create new windows
for these two peripheral group reflecting the internal
structure of the B0 SoC.

This SoC has up to 256 possible GPIOs due to having 8
registers with 32 GPIOs in each available.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
 arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi | 150 +++++++++++++++++++++-
 1 file changed, 147 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi b/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
index 48d618e75866452a64adfdc781ac0ea3c2eff3e8..a47c5d6d034a7ae56803a651636148383acb8cc9 100644
--- a/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
+++ b/arch/arm64/boot/dts/broadcom/bcmbca/bcm63158.dtsi
@@ -1,6 +1,7 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 /*
  * Copyright 2022 Broadcom Ltd.
+ * This DTSI is for the B0 and later revision of the SoC
  */
 
 #include <dt-bindings/interrupt-controller/irq.h>
@@ -119,11 +120,107 @@ gic: interrupt-controller@1000 {
 		};
 	};
 
+	/* PERF Peripherals */
 	bus@ff800000 {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges = <0x0 0x0 0xff800000 0x800000>;
+		ranges = <0x0 0x0 0xff800000 0x3000>;
+
+		/* GPIOs 0 .. 31 */
+		gpio0: gpio@500 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x500 0x04>, <0x520 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 32 .. 63 */
+		gpio1: gpio@504 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x504 0x04>, <0x524 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 64 .. 95 */
+		gpio2: gpio@508 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x508 0x04>, <0x528 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 96 .. 127 */
+		gpio3: gpio@50c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x50c 0x04>, <0x52c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 128 .. 159 */
+		gpio4: gpio@510 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x510 0x04>, <0x530 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 160 .. 191 */
+		gpio5: gpio@514 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x514 0x04>, <0x534 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 192 .. 223 */
+		gpio6: gpio@518 {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x518 0x04>, <0x538 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+		/* GPIOs 224 .. 255 */
+		gpio7: gpio@51c {
+			compatible = "brcm,bcm6345-gpio";
+			reg = <0x51c 0x04>, <0x53c 0x04>;
+			reg-names = "dirout", "dat";
+			gpio-controller;
+			#gpio-cells = <2>;
+			status = "disabled";
+		};
+
+
+		leds: led-controller@800 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			compatible = "brcm,bcm63138-leds";
+			reg = <0x800 0xdc>;
+			status = "disabled";
+		};
+
+		rng@b80 {
+			compatible = "brcm,iproc-rng200";
+			reg = <0xb80 0x28>;
+			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
+		};
 
 		hsspi: spi@1000 {
 			#address-cells = <1>;
@@ -150,14 +247,61 @@ nandcs: nand@0 {
 				reg = <0>;
 			};
 		};
+	};
+
+	/* B0 AHB Peripherals */
+	bus@ff810000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff810000 0x2000>;
+
+		pl081_dma: dma-controller@1000 {
+			compatible = "arm,pl081", "arm,primecell";
+			// The magic B105F00D info is missing
+			arm,primecell-periphid = <0x00041081>;
+			reg = <0x1000 0x1000>;
+			interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>;
+			memcpy-burst-size = <256>;
+			memcpy-bus-width = <32>;
+			clocks = <&periph_clk>;
+			clock-names = "apb_pclk";
+			#dma-cells = <2>;
+		};
+	};
+
+	/* B0 ARM UART Peripheral block */
+	bus@ff812000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x0 0xff812000 0x3000>;
 
-		uart0: serial@12000 {
+		uart0: serial@0 {
 			compatible = "arm,pl011", "arm,primecell";
-			reg = <0x12000 0x1000>;
+			reg = <0x0 0x1000>;
 			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&uart_clk>, <&uart_clk>;
 			clock-names = "uartclk", "apb_pclk";
 			status = "disabled";
 		};
+
+		uart1: serial@1000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x1000 0x1000>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
+
+		uart2: serial@2000 {
+			compatible = "arm,pl011", "arm,primecell";
+			reg = <0x2000 0x1000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&uart_clk>, <&uart_clk>;
+			clock-names = "uartclk", "apb_pclk";
+			status = "disabled";
+		};
 	};
 };

-- 
2.48.1

Re: [PATCH 02/12] dt-bindings: rng: r200: Add interrupt property

[Krzysztof Kozlowski]

On Fri, Mar 28, 2025 at 08:43:52AM +0100, Linus Walleij wrote:
> This IP block has an interrupt. Add it and add it to the
> example as well.
> 
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
>  Documentation/devicetree/bindings/rng/brcm,iproc-rng200.yaml | 6 ++++++
>  1 file changed, 6 insertions(+)

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof