* [PATCH v2 2/3] regulator: max77675: Add MAX77675 regulator driver
2025-09-29 10:56 [PATCH v2 0/3] MAX77675 regulator driver: Add support for MAX77675 device Joan-Na-adi
2025-09-29 10:56 ` [PATCH v2 1/3] dt-bindings: regulator: Add MAX77675 binding header Joan-Na-adi
@ 2025-09-29 10:56 ` Joan-Na-adi
2025-09-29 17:38 ` Mark Brown
2025-09-29 10:56 ` [PATCH v2 3/3] dt-bindings: regulator: Add MAX77675 regulator binding Joan-Na-adi
2 siblings, 1 reply; 7+ messages in thread
From: Joan-Na-adi @ 2025-09-29 10:56 UTC (permalink / raw)
To: Liam Girdwood
Cc: Mark Brown, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
linux-kernel, devicetree, Joan Na, kernel test robot
From: Joan Na <joan.na@analog.com>
This patch adds support for the Maxim Integrated MAX77675 PMIC regulator.
The MAX77675 is a compact, highly efficient SIMO (Single Inductor Multiple Output)
power management IC that provides four programmable buck-boost switching regulators
with only one inductor. It supports up to 700mA total output current and operates
from a single-cell Li-ion battery.
An integrated power-up sequencer and I2C interface allow flexible startup
configuration and runtime control.
Fixes:
- Removed unused variable 'value'
- Removed duplicate .list_voltage initializer
- Wrapped of_match_table with of_match_ptr() to fix build failure when CONFIG_OF is not set
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/20250927.cU4bEADk-lkp@intel.com/
Signed-off-by: Joan Na <joan.na@analog.com>
---
drivers/regulator/Kconfig | 9 +
drivers/regulator/Makefile | 1 +
drivers/regulator/max77675-regulator.c | 792 +++++++++++++++++++++++++
drivers/regulator/max77675-regulator.h | 252 ++++++++
4 files changed, 1054 insertions(+)
create mode 100644 drivers/regulator/max77675-regulator.c
create mode 100644 drivers/regulator/max77675-regulator.h
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index eaa6df1c9f80..783e718e64a4 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -641,6 +641,15 @@ config REGULATOR_MAX77650
Semiconductor. This device has a SIMO with three independent
power rails and an LDO.
+config REGULATOR_MAX77675
+ tristate "Maxim MAX77675 regulator driver"
+ depends on I2C
+ select REGMAP_I2C
+ help
+ This driver controls the Maxim MAX77675 power regulator via I2C.
+ It supports four programmable buck-boost outputs.
+ Say Y here to enable the regulator driver
+
config REGULATOR_MAX77857
tristate "ADI MAX77857/MAX77831 regulator support"
depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index be98b29d6675..fa9dadd71edd 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -77,6 +77,7 @@ obj-$(CONFIG_REGULATOR_MAX77503) += max77503-regulator.o
obj-$(CONFIG_REGULATOR_MAX77541) += max77541-regulator.o
obj-$(CONFIG_REGULATOR_MAX77620) += max77620-regulator.o
obj-$(CONFIG_REGULATOR_MAX77650) += max77650-regulator.o
+obj-$(CONFIG_REGULATOR_MAX77675) += max77675-regulator.o
obj-$(CONFIG_REGULATOR_MAX8649) += max8649.o
obj-$(CONFIG_REGULATOR_MAX8660) += max8660.o
obj-$(CONFIG_REGULATOR_MAX8893) += max8893.o
diff --git a/drivers/regulator/max77675-regulator.c b/drivers/regulator/max77675-regulator.c
new file mode 100644
index 000000000000..8096df543727
--- /dev/null
+++ b/drivers/regulator/max77675-regulator.c
@@ -0,0 +1,792 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright (c) 2025 Analog Devices, Inc.
+ * ADI regulator driver for MAX77675.
+ */
+
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/of.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/consumer.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/bitfield.h>
+#include <dt-bindings/regulator/maxim,max77675-regulator.h>
+
+#include "max77675-regulator.h"
+
+struct max77675_regulator_pdata {
+ u8 fps_slot;
+ u8 dvs_slew_rate;
+};
+
+struct max77675_config {
+ u8 drv_slew_rate;
+ u8 latency_mode;
+ u8 drv_sbb_strength;
+ u8 manual_reset_time;
+ u8 en_pullup_disable;
+ u8 bias_low_power_request;
+ u8 simo_int_ldo_always_on;
+ u8 en_mode;
+ u8 en_debounce_time;
+};
+
+struct max77675_regulator {
+ struct device *dev;
+ struct regmap *regmap;
+ struct max77675_config config;
+ struct max77675_regulator_pdata pdata[MAX77675_ID_NUM_MAX];
+};
+
+/**
+ * Set latency mode.
+ *
+ * @param maxreg Pointer to max77675 device structure.
+ * @param enable true to enable latency mode, false to disable.
+ */
+static int max77675_set_latency_mode(struct max77675_regulator *maxreg, bool enable)
+{
+ return regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_SBB_TOP_B,
+ MAX77675_LAT_MODE_BIT,
+ FIELD_PREP(MAX77675_LAT_MODE_BIT, enable));
+}
+
+/**
+ * Set DVS slew rate mode.
+ *
+ * @param maxreg Pointer to max77675 device structure.
+ * @param enable true to use DVS-controlled slew rate, false for fixed 2mV/us.
+ */
+static int max77675_set_dvs_slew_rate(struct max77675_regulator *maxreg, bool enable)
+{
+ return regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_SBB_TOP_B,
+ MAX77675_DVS_SLEW_BIT,
+ FIELD_PREP(MAX77675_DVS_SLEW_BIT, enable));
+}
+
+/**
+ * Set drive strength.
+ *
+ * @param maxreg Pointer to max77675 device structure.
+ * @param strength 2-bit drive strength value (0-3).
+ *
+ * @return 0 on success, negative error code on failure.
+ */
+static int max77675_set_drv_sbb_strength(struct max77675_regulator *maxreg, u8 strength)
+{
+ return regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_SBB_TOP_A,
+ MAX77675_DRV_SBB_MASK,
+ FIELD_PREP(MAX77675_DRV_SBB_MASK, strength));
+}
+
+/**
+ * Set manual reset time (MRT) for EN pin.
+ *
+ * @param maxreg Pointer to max77675 device structure.
+ * @param mrt 2-bit value (0x0: 4s, 0x1: 8s, 0x2: 12s, 0x3: 16s)
+ */
+static int max77675_set_manual_reset_time(struct max77675_regulator *maxreg, u8 mrt)
+{
+ return regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_MRT_MASK,
+ FIELD_PREP(MAX77675_MRT_MASK, mrt));
+}
+
+/**
+ * Enable or disable internal pull-up resistor on EN pin.
+ *
+ * @param maxreg Pointer to max77675 device structure.
+ * @param disable true to disable pull-up, false to enable
+ */
+static int max77675_set_en_pullup_disable(struct max77675_regulator *maxreg, bool disable)
+{
+ return regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_PU_DIS_BIT,
+ FIELD_PREP(MAX77675_PU_DIS_BIT, disable));
+}
+
+/**
+ * Request main bias to enter low-power mode.
+ *
+ * @param maxreg Pointer to max77675 device structure.
+ * @param enable true to request low-power mode, false for normal
+ */
+static int max77675_set_bias_low_power_request(struct max77675_regulator *maxreg, bool enable)
+{
+ return regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_BIAS_LPM_BIT,
+ FIELD_PREP(MAX77675_BIAS_LPM_BIT, enable));
+}
+
+/**
+ * Force SIMO internal LDO to always supply 1.8V.
+ *
+ * @param maxreg Pointer to max77675 device structure.
+ * @param enable true to always supply 1.8V, false for normal operation
+ */
+static int max77675_set_simo_int_ldo_always_on(struct max77675_regulator *maxreg, bool enable)
+{
+ return regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_SIMO_CH_DIS_BIT,
+ FIELD_PREP(MAX77675_SIMO_CH_DIS_BIT, enable));
+}
+
+/**
+ * Set EN pin mode.
+ *
+ * @param maxreg Pointer to max77675 device structure.
+ * @param mode 2-bit value: 0x0 (push-button), 0x1 (slide-switch), 0x2 (logic)
+ */
+static int max77675_set_en_mode(struct max77675_regulator *maxreg, u8 mode)
+{
+ return regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_EN_MODE_MASK,
+ FIELD_PREP(MAX77675_EN_MODE_MASK, mode));
+}
+
+/**
+ * Set debounce time for EN pin.
+ *
+ * @param maxreg Pointer to max77675 device structure.
+ * @param debounce_30ms true for 30ms, false for 100us
+ */
+static int max77675_set_en_debounce_time(struct max77675_regulator *maxreg, bool debounce_30ms)
+{
+ return regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_GLBL_A,
+ MAX77675_DBEN_EN_BIT,
+ FIELD_PREP(MAX77675_DBEN_EN_BIT, debounce_30ms));
+}
+
+static int max77675_regulator_get_fps_src(struct max77675_regulator *maxreg, int id)
+{
+ unsigned int reg_addr;
+ unsigned int val;
+ int ret;
+
+ switch (id) {
+ case MAX77675_ID_SBB0:
+ reg_addr = MAX77675_REG_CNFG_SBB0_B;
+ break;
+ case MAX77675_ID_SBB1:
+ reg_addr = MAX77675_REG_CNFG_SBB1_B;
+ break;
+ case MAX77675_ID_SBB2:
+ reg_addr = MAX77675_REG_CNFG_SBB2_B;
+ break;
+ case MAX77675_ID_SBB3:
+ reg_addr = MAX77675_REG_CNFG_SBB3_B;
+ break;
+ default:
+ dev_err(maxreg->dev, "Invalid regulator id: %d\n", id);
+ return -EINVAL;
+ }
+
+ ret = regmap_read(maxreg->regmap, reg_addr, &val);
+ if (ret < 0) {
+ dev_err(maxreg->dev, "Failed to read FPS source (reg 0x%02x): %d\n",
+ reg_addr, ret);
+ return ret;
+ }
+
+ return val & MAX77675_EN_SBB_MASK;
+}
+
+static int max77675_regulator_set_fps_src(struct max77675_regulator *maxreg, int id, u8 fps_src)
+{
+ unsigned int reg_addr;
+ int ret;
+
+ switch (id) {
+ case MAX77675_ID_SBB0:
+ reg_addr = MAX77675_REG_CNFG_SBB0_B;
+ break;
+ case MAX77675_ID_SBB1:
+ reg_addr = MAX77675_REG_CNFG_SBB1_B;
+ break;
+ case MAX77675_ID_SBB2:
+ reg_addr = MAX77675_REG_CNFG_SBB2_B;
+ break;
+ case MAX77675_ID_SBB3:
+ reg_addr = MAX77675_REG_CNFG_SBB3_B;
+ break;
+ default:
+ dev_err(maxreg->dev, "Invalid regulator id: %d\n", id);
+ return -EINVAL;
+ }
+
+ ret = regmap_update_bits(maxreg->regmap, reg_addr,
+ MAX77675_EN_SBB_MASK, fps_src);
+ if (ret < 0) {
+ dev_err(maxreg->dev, "Failed to set FPS source (reg 0x%02x): %d\n",
+ reg_addr, ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+/**
+ * max77675_set_sbb_slew_rate - Set the slew rate for a specific SBB regulator channel
+ *
+ * @maxreg: Pointer to the max77675 regulator structure
+ * @id: Regulator channel ID (ID_SBB0 ~ ID_SBB3)
+ * @val: Slew rate value (0 = 2mV/us, 1 = use DVS_SLEW)
+ *
+ * This function configures the slew rate control source for the specified SBB channel by
+ * updating the corresponding bits in the CNFG_SBB_TOP_B register.
+ *
+ * Return: 0 on success, negative error code on failure (e.g., invalid channel ID).
+ */
+static int max77675_set_sbb_slew_rate(struct max77675_regulator *maxreg, int id, u8 val)
+{
+ u8 mask, value;
+
+ switch (id) {
+ case MAX77675_ID_SBB0:
+ mask = MAX77675_SR_SBB0_BIT;
+ value = FIELD_PREP(MAX77675_SR_SBB0_BIT, val);
+ break;
+
+ case MAX77675_ID_SBB1:
+ mask = MAX77675_SR_SBB1_BIT;
+ value = FIELD_PREP(MAX77675_SR_SBB1_BIT, val);
+ break;
+
+ case MAX77675_ID_SBB2:
+ mask = MAX77675_SR_SBB2_BIT;
+ value = FIELD_PREP(MAX77675_SR_SBB2_BIT, val);
+ break;
+
+ case MAX77675_ID_SBB3:
+ mask = MAX77675_SR_SBB3_BIT;
+ value = FIELD_PREP(MAX77675_SR_SBB3_BIT, val);
+ break;
+
+ default:
+ return -EINVAL;
+ }
+
+ return regmap_update_bits(maxreg->regmap, MAX77675_REG_CNFG_SBB_TOP_B, mask, value);
+}
+
+static int max77675_init_regulator(struct max77675_regulator *maxreg, int id)
+{
+ struct max77675_regulator_pdata *rpdata = &maxreg->pdata[id];
+ int ret;
+
+ if (rpdata->fps_slot == MAX77675_FPS_DEF) {
+ ret = max77675_regulator_get_fps_src(maxreg, id);
+ if (ret < 0) {
+ dev_err(maxreg->dev, "Failed to read FPS source for ID %d\n", id);
+ return ret;
+ }
+ rpdata->fps_slot = ret;
+ }
+
+ ret = max77675_regulator_set_fps_src(maxreg, id, rpdata->fps_slot);
+ if (ret)
+ dev_warn(maxreg->dev, "Failed to set FPS source for ID %d\n", id);
+
+ ret = max77675_set_sbb_slew_rate(maxreg, id, rpdata->dvs_slew_rate);
+ if (ret)
+ dev_warn(maxreg->dev, "Failed to set slew rate for ID %d\n", id);
+
+ return 0;
+}
+
+static int max77675_of_parse_cb(struct device_node *np,
+ const struct regulator_desc *desc,
+ struct regulator_config *config)
+{
+ struct max77675_regulator *maxreg = config->driver_data;
+ struct max77675_regulator_pdata *rpdata = &maxreg->pdata[desc->id];
+ u32 pval;
+ int ret;
+
+ /* Parse FPS slot from DT */
+ ret = of_property_read_u32(np, "maxim,fps-slot", &pval);
+ rpdata->fps_slot = (!ret) ? (u8)pval : MAX77675_FPS_DEF;
+
+ /* Parse slew rate control source */
+ ret = of_property_read_u32(np, "maxim,slew-rate-use-drv", &pval);
+ rpdata->dvs_slew_rate = (!ret) ? (u8)pval : 0;
+
+ /* Apply parsed configuration */
+ return max77675_init_regulator(maxreg, desc->id);
+}
+
+static int max77675_get_error_flags(struct regulator_dev *rdev, unsigned int *flags)
+{
+ struct max77675_regulator *maxreg = rdev_get_drvdata(rdev);
+ unsigned int int_flags;
+ int id = rdev_get_id(rdev);
+ int ret;
+
+ ret = regmap_read(maxreg->regmap, MAX77675_REG_INT_GLBL, &int_flags);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to read INT_GLBL: %d\n", ret);
+ return ret;
+ }
+
+ *flags = 0;
+
+ switch (id) {
+ case MAX77675_ID_SBB0:
+ if (int_flags & MAX77675_INT_SBB0_F_BIT)
+ *flags |= REGULATOR_ERROR_FAIL;
+ break;
+ case MAX77675_ID_SBB1:
+ if (int_flags & MAX77675_INT_SBB1_F_BIT)
+ *flags |= REGULATOR_ERROR_FAIL;
+ break;
+ case MAX77675_ID_SBB2:
+ if (int_flags & MAX77675_INT_SBB2_F_BIT)
+ *flags |= REGULATOR_ERROR_FAIL;
+ break;
+ case MAX77675_ID_SBB3:
+ if (int_flags & MAX77675_INT_SBB3_F_BIT)
+ *flags |= REGULATOR_ERROR_FAIL;
+ break;
+ default:
+ dev_warn(maxreg->dev, "Unsupported regulator ID: %d\n", id);
+ break;
+ }
+
+ if (int_flags & MAX77675_INT_TJAL2_R_BIT) {
+ /* TJAL2 interrupt: Over-temperature condition (above 120 degree) */
+ *flags |= REGULATOR_ERROR_OVER_TEMP;
+ }
+
+ return 0;
+}
+
+static const struct regulator_ops max77675_regulator_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .map_voltage = regulator_map_voltage_linear,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_active_discharge = regulator_set_active_discharge_regmap,
+ .get_error_flags = max77675_get_error_flags,
+};
+
+static struct regulator_desc max77675_regulators[MAX77675_ID_NUM_MAX] = {
+ {
+ .name = "sbb0",
+ .of_match = of_match_ptr("sbb0"),
+ .regulators_node = of_match_ptr("regulators"),
+ .of_parse_cb = max77675_of_parse_cb,
+ .id = MAX77675_ID_SBB0,
+ .ops = &max77675_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .n_voltages = MAX77675_NUM_LEVELS_25MV,
+ .min_uV = MAX77675_MIN_UV,
+ .uV_step = MAX77675_STEP_25MV,
+ .vsel_reg = MAX77675_REG_CNFG_SBB0_A,
+ .vsel_mask = MAX77675_TV_SBB0_MASK,
+ .enable_reg = MAX77675_REG_CNFG_SBB0_B,
+ .enable_mask = MAX77675_EN_SBB0_MASK,
+ .enable_val = MAX77675_ENABLE_ON,
+ .disable_val = MAX77675_ENABLE_OFF,
+ .active_discharge_off = MAX77675_REGULATOR_AD_OFF,
+ .active_discharge_on = MAX77675_REGULATOR_AD_ON,
+ .active_discharge_mask = MAX77675_REGULATOR_AD_MASK,
+ .active_discharge_reg = MAX77675_REG_CNFG_SBB0_B,
+ },
+ {
+ .name = "sbb1",
+ .of_match = of_match_ptr("sbb1"),
+ .regulators_node = of_match_ptr("regulators"),
+ .of_parse_cb = max77675_of_parse_cb,
+ .id = MAX77675_ID_SBB1,
+ .ops = &max77675_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .n_voltages = MAX77675_NUM_LEVELS_25MV,
+ .min_uV = MAX77675_MIN_UV,
+ .uV_step = MAX77675_STEP_25MV,
+ .vsel_reg = MAX77675_REG_CNFG_SBB1_A,
+ .vsel_mask = MAX77675_TV_SBB1_MASK,
+ .enable_reg = MAX77675_REG_CNFG_SBB1_B,
+ .enable_mask = MAX77675_EN_SBB1_MASK,
+ .enable_val = MAX77675_ENABLE_ON,
+ .disable_val = MAX77675_ENABLE_OFF,
+ .active_discharge_off = MAX77675_REGULATOR_AD_OFF,
+ .active_discharge_on = MAX77675_REGULATOR_AD_ON,
+ .active_discharge_mask = MAX77675_REGULATOR_AD_MASK,
+ .active_discharge_reg = MAX77675_REG_CNFG_SBB1_B,
+ },
+ {
+ .name = "sbb2",
+ .of_match = of_match_ptr("sbb2"),
+ .regulators_node = of_match_ptr("regulators"),
+ .of_parse_cb = max77675_of_parse_cb,
+ .id = MAX77675_ID_SBB2,
+ .ops = &max77675_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .n_voltages = MAX77675_NUM_LEVELS_25MV,
+ .min_uV = MAX77675_MIN_UV,
+ .uV_step = MAX77675_STEP_25MV,
+ .vsel_reg = MAX77675_REG_CNFG_SBB2_A,
+ .vsel_mask = MAX77675_TV_SBB2_MASK,
+ .enable_reg = MAX77675_REG_CNFG_SBB2_B,
+ .enable_mask = MAX77675_EN_SBB2_MASK,
+ .enable_val = MAX77675_ENABLE_ON,
+ .disable_val = MAX77675_ENABLE_OFF,
+ .active_discharge_off = MAX77675_REGULATOR_AD_OFF,
+ .active_discharge_on = MAX77675_REGULATOR_AD_ON,
+ .active_discharge_mask = MAX77675_REGULATOR_AD_MASK,
+ .active_discharge_reg = MAX77675_REG_CNFG_SBB2_B,
+ },
+ {
+ .name = "sbb3",
+ .of_match = of_match_ptr("sbb3"),
+ .regulators_node = of_match_ptr("regulators"),
+ .of_parse_cb = max77675_of_parse_cb,
+ .id = MAX77675_ID_SBB3,
+ .ops = &max77675_regulator_ops,
+ .type = REGULATOR_VOLTAGE,
+ .owner = THIS_MODULE,
+ .n_voltages = MAX77675_NUM_LEVELS_25MV,
+ .min_uV = MAX77675_MIN_UV,
+ .uV_step = MAX77675_STEP_25MV,
+ .vsel_reg = MAX77675_REG_CNFG_SBB3_A,
+ .vsel_mask = MAX77675_TV_SBB3_MASK,
+ .enable_reg = MAX77675_REG_CNFG_SBB3_B,
+ .enable_mask = MAX77675_EN_SBB3_MASK,
+ .enable_val = MAX77675_ENABLE_ON,
+ .disable_val = MAX77675_ENABLE_OFF,
+ .active_discharge_off = MAX77675_REGULATOR_AD_OFF,
+ .active_discharge_on = MAX77675_REGULATOR_AD_ON,
+ .active_discharge_mask = MAX77675_REGULATOR_AD_MASK,
+ .active_discharge_reg = MAX77675_REG_CNFG_SBB3_B,
+ },
+};
+
+static const struct regmap_config max77675_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = MAX77675_MAX_REGISTER,
+ .cache_type = REGCACHE_NONE,
+};
+
+static int max77675_apply_config(struct max77675_regulator *maxreg)
+{
+ const struct max77675_config *config = &maxreg->config;
+ int ret;
+
+ ret = max77675_set_dvs_slew_rate(maxreg, config->drv_slew_rate);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set DVS slew rate: %d\n", ret);
+ return ret;
+ }
+
+ ret = max77675_set_latency_mode(maxreg, config->latency_mode);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set latency mode: %d\n", ret);
+ return ret;
+ }
+
+ ret = max77675_set_drv_sbb_strength(maxreg, config->drv_sbb_strength);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set drive strength: %d\n", ret);
+ return ret;
+ }
+
+ ret = max77675_set_manual_reset_time(maxreg, config->manual_reset_time);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set manual reset time: %d\n", ret);
+ return ret;
+ }
+
+ ret = max77675_set_en_pullup_disable(maxreg, config->en_pullup_disable);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set EN pull-up disable: %d\n", ret);
+ return ret;
+ }
+
+ ret = max77675_set_bias_low_power_request(maxreg, config->bias_low_power_request);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set bias low-power request: %d\n", ret);
+ return ret;
+ }
+
+ ret = max77675_set_simo_int_ldo_always_on(maxreg, config->simo_int_ldo_always_on);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set SIMO internal LDO always-on: %d\n", ret);
+ return ret;
+ }
+
+ ret = max77675_set_en_mode(maxreg, config->en_mode);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set EN mode: %d\n", ret);
+ return ret;
+ }
+
+ ret = max77675_set_en_debounce_time(maxreg, config->en_debounce_time);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to set EN debounce time: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int max77675_parse_config(struct max77675_regulator *maxreg)
+{
+ struct device_node *np = maxreg->dev->of_node;
+ struct max77675_config *config = &maxreg->config;
+ int ret;
+ u32 val;
+
+ /* drv slew rate */
+ ret = of_property_read_u32(np, "maxim,dvs-slew-rate", &val);
+ if (ret < 0)
+ val = MAX77675_DVS_SLEW_5MV;
+ config->drv_slew_rate = val;
+
+ /* latency mode */
+ ret = of_property_read_u32(np, "maxim,latency-mode", &val);
+ if (ret < 0)
+ val = MAX77675_LAT_MODE_HIGH_LATENCY;
+ config->latency_mode = val;
+
+ /* drive strength */
+ ret = of_property_read_u32(np, "maxim,drv-sbb-strength", &val);
+ if (ret < 0)
+ val = MAX77675_DRV_SBB_FASTEST;
+ config->drv_sbb_strength = val;
+
+ /* Manual reset time for EN pin */
+ ret = of_property_read_u32(np, "maxim,manual-reset-time", &val);
+ if (ret < 0)
+ val = MAX77675_MRT_4S;
+ config->manual_reset_time = val;
+
+ /* Disable internal pull-up resistor on EN pin */
+ ret = of_property_read_u32(np, "maxim,en-pullup-disable", &val);
+ if (ret < 0)
+ val = MAX77675_PU_EN;
+ config->en_pullup_disable = val;
+
+ /* Request low-power mode for main bias */
+ ret = of_property_read_u32(np, "maxim,bias-low-power-request", &val);
+ if (ret < 0)
+ val = MAX77675_BIAS_NORMAL;
+ config->bias_low_power_request = val;
+
+ /* Force internal LDO to always supply 1.8V */
+ ret = of_property_read_u32(np, "maxim,simo-int-ldo-always-on", &val);
+ if (ret < MAX77675_SIMO_INT_NORMAL)
+ val = MAX77675_BIAS_NORMAL;
+ config->simo_int_ldo_always_on = val;
+
+ /* EN pin mode: push-button, slide-switch, or logic */
+ ret = of_property_read_u32(np, "maxim,en-mode", &val);
+ if (ret < 0)
+ val = MAX77675_EN_SLIDE_SWITCH;
+ config->en_mode = val;
+
+ /* Debounce time for EN pin */
+ ret = of_property_read_u32(np, "maxim,en-debounce-time", &val);
+ if (ret < 0)
+ val = MAX77675_DBEN_100US;
+ config->en_debounce_time = val;
+
+ /* Debug print all parsed values */
+ pr_info("MAX77675 config parsed:\n"
+ " dvs_slew_rate: %u\n"
+ " latency_mode: %u\n"
+ " drv_sbb_strength: %u\n"
+ " manual_reset_time: %u\n"
+ " en_pullup_disable: %u\n"
+ " bias_low_power_request: %u\n"
+ " simo_int_ldo_always_on: %u\n"
+ " en_mode: %u\n"
+ " en_debounce_time: %u\n",
+ config->drv_slew_rate,
+ config->latency_mode,
+ config->drv_sbb_strength,
+ config->manual_reset_time,
+ config->en_pullup_disable,
+ config->bias_low_power_request,
+ config->simo_int_ldo_always_on,
+ config->en_mode,
+ config->en_debounce_time);
+
+ ret = max77675_apply_config(maxreg);
+
+ return ret;
+}
+
+static int max77675_init_event(struct max77675_regulator *maxreg)
+{
+ unsigned int ercflag, int_glbl;
+ int ret;
+
+ ret = regmap_read(maxreg->regmap, MAX77675_REG_ERCF_GLBL, &ercflag);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to read CID register: %d\n", ret);
+ return ret;
+ }
+
+ ret = regmap_read(maxreg->regmap, MAX77675_REG_INT_GLBL, &int_glbl);
+ if (ret) {
+ dev_err(maxreg->dev, "Failed to read INT_GLBL register: %d\n", ret);
+ return ret;
+ }
+
+ if (ercflag & MAX77675_SFT_CRST_F_BIT)
+ dev_info(maxreg->dev, "Software Cold Reset Flag is set\n");
+
+ if (ercflag & MAX77675_SFT_OFF_F_BIT)
+ dev_info(maxreg->dev, "Software Off Flag is set\n");
+
+ if (ercflag & MAX77675_MRST_BIT)
+ dev_info(maxreg->dev, "Manual Reset Timer Flag is set\n");
+
+ if (ercflag & MAX77675_UVLO_BIT)
+ dev_info(maxreg->dev, "Undervoltage Lockout Flag is set\n");
+
+ if (ercflag & MAX77675_OVLO_BIT)
+ dev_info(maxreg->dev, "Overvoltage Lockout Flag is set\n");
+
+ if (ercflag & MAX77675_TOVLD_BIT)
+ dev_info(maxreg->dev, "Thermal Overload Flag is set\n");
+
+ if (int_glbl & MAX77675_INT_SBB3_F_BIT)
+ dev_info(maxreg->dev, "SBB3 Channel Fault Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_SBB2_F_BIT)
+ dev_info(maxreg->dev, "SBB2 Channel Fault Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_SBB1_F_BIT)
+ dev_info(maxreg->dev, "SBB1 Channel Fault Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_SBB0_F_BIT)
+ dev_info(maxreg->dev, "SBB0 Channel Fault Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_TJAL2_R_BIT)
+ dev_info(maxreg->dev, "Thermal Alarm 2 Rising Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_TJAL1_R_BIT)
+ dev_info(maxreg->dev, "Thermal Alarm 1 Rising Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_EN_R_BIT)
+ dev_info(maxreg->dev, "nEN Rising Edge Interrupt occurred\n");
+
+ if (int_glbl & MAX77675_INT_EN_F_BIT)
+ dev_info(maxreg->dev, "nEN Falling Edge Interrupt occurred\n");
+
+ return 0;
+}
+
+static int max77675_regulator_probe(struct i2c_client *client)
+{
+ struct max77675_regulator *maxreg;
+ struct regulator_config config = {};
+ struct device_node *regulators_np;
+ int i, ret;
+
+ maxreg = devm_kzalloc(&client->dev, sizeof(*maxreg), GFP_KERNEL);
+ if (!maxreg)
+ return -ENOMEM;
+
+ maxreg->dev = &client->dev;
+
+ maxreg->regmap = devm_regmap_init_i2c(client, &max77675_regmap_config);
+ if (IS_ERR(maxreg->regmap))
+ return dev_err_probe(maxreg->dev,
+ PTR_ERR(maxreg->regmap),
+ "Failed to init regmap\n");
+
+ ret = max77675_init_event(maxreg);
+ if (ret)
+ return dev_err_probe(maxreg->dev, ret, "Failed to init event\n");
+
+ ret = max77675_parse_config(maxreg);
+ if (ret)
+ return dev_err_probe(maxreg->dev, ret, "Failed to apply config\n");
+
+ config.dev = &client->dev;
+ config.regmap = maxreg->regmap;
+ config.driver_data = maxreg;
+
+ regulators_np = of_get_child_by_name(client->dev.of_node, "regulators");
+ if (!regulators_np) {
+ dev_err(maxreg->dev, "No 'regulators' subnode found in DT\n");
+ return -EINVAL;
+ }
+
+ for (i = 0; i < MAX77675_ID_NUM_MAX; i++) {
+ const struct regulator_desc *desc = &max77675_regulators[i];
+ struct regulator_dev *rdev;
+ struct device_node *child_np;
+
+ child_np = of_get_child_by_name(regulators_np, desc->name);
+ if (!child_np) {
+ dev_warn(maxreg->dev, "No DT node for regulator %s\n", desc->name);
+ continue;
+ }
+
+ config.of_node = child_np;
+
+ rdev = devm_regulator_register(&client->dev, desc, &config);
+ if (IS_ERR(rdev)) {
+ ret = PTR_ERR(rdev);
+ dev_err(maxreg->dev,
+ "Failed to register regulator %d (%s): %d\n",
+ i, desc->name, ret);
+ of_node_put(child_np);
+ return ret;
+ }
+ of_node_put(child_np);
+ }
+
+ i2c_set_clientdata(client, maxreg);
+
+ return 0;
+}
+
+static void max77675_regulator_remove(struct i2c_client *client)
+{
+ struct max77675_regulator *maxreg = i2c_get_clientdata(client);
+
+ dev_info(maxreg->dev, "MAX77675 regulators removed\n");
+}
+
+static const struct i2c_device_id max77675_i2c_id[] = {
+ { "max77675", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, max77675_i2c_id);
+
+static const struct of_device_id __maybe_unused max77675_of_match[] = {
+ { .compatible = "maxim,max77675", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, max77675_of_match);
+
+static struct i2c_driver max77675_regulator_driver = {
+ .driver = {
+ .name = "max77675",
+ .of_match_table = of_match_ptr(max77675_of_match),
+ },
+ .probe = max77675_regulator_probe,
+ .remove = max77675_regulator_remove,
+ .id_table = max77675_i2c_id,
+};
+
+module_i2c_driver(max77675_regulator_driver);
+
+MODULE_DESCRIPTION("MAX77675 Regulator Driver");
+MODULE_AUTHOR("Joan Na <joan.na@analog.com>");
+MODULE_LICENSE("GPL");
diff --git a/drivers/regulator/max77675-regulator.h b/drivers/regulator/max77675-regulator.h
new file mode 100644
index 000000000000..087956ba7834
--- /dev/null
+++ b/drivers/regulator/max77675-regulator.h
@@ -0,0 +1,252 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * MAX77675 Register Definitions
+ * Reference: MAX77675 Datasheet
+ */
+
+#ifndef __MAX77675_REG_H__
+#define __MAX77675_REG_H__
+
+#include <linux/bitops.h>
+
+/* Register Addresses */
+#define MAX77675_REG_CNFG_GLBL_A 0x00
+#define MAX77675_REG_CNFG_GLBL_B 0x01
+#define MAX77675_REG_INT_GLBL 0x02
+#define MAX77675_REG_INTM_GLBL 0x03
+#define MAX77675_REG_STAT_GLBL 0x04
+#define MAX77675_REG_ERCF_GLBL 0x05
+#define MAX77675_REG_CID 0x06
+#define MAX77675_REG_CNFG_SBB_TOP_A 0x07
+#define MAX77675_REG_CNFG_SBB0_A 0x08
+#define MAX77675_REG_CNFG_SBB0_B 0x09
+#define MAX77675_REG_CNFG_SBB1_A 0x0A
+#define MAX77675_REG_CNFG_SBB1_B 0x0B
+#define MAX77675_REG_CNFG_SBB2_A 0x0C
+#define MAX77675_REG_CNFG_SBB2_B 0x0D
+#define MAX77675_REG_CNFG_SBB3_A 0x0E
+#define MAX77675_REG_CNFG_SBB3_B 0x0F
+#define MAX77675_REG_CNFG_SBB_TOP_B 0x10
+
+/* CNFG_GLBL_A (0x00) bit masks and shifts */
+#define MAX77675_MRT_MASK GENMASK(7, 6) /* Manual Reset Time (bits 7:6) */
+#define MAX77675_MRT_SHIFT 6
+#define MAX77675_PU_DIS_BIT BIT(5) /* Pullup Disable (bit 5) */
+#define MAX77675_PU_DIS_SHIFT 5
+#define MAX77675_BIAS_LPM_BIT BIT(4) /* Bias Low Power Mode (bit 4) */
+#define MAX77675_BIAS_LPM_SHIFT 4
+#define MAX77675_SIMO_CH_DIS_BIT BIT(3) /* SIMO Internal Channel Disable (bit 3) */
+#define MAX77675_SIMO_CH_DIS_SHIFT 3
+#define MAX77675_EN_MODE_MASK GENMASK(2, 1) /* nEN Mode (bits 2:1) */
+#define MAX77675_EN_MODE_SHIFT 1
+#define MAX77675_DBEN_EN_BIT BIT(0) /* Debounce Enable (bit 0) */
+#define MAX77675_DBEN_EN_SHIFT 0
+
+/* CNFG_GLBL_B (0x01) */
+#define MAX77675_SFT_CTRL_MASK GENMASK(2, 0) /* Soft Start Control */
+#define MAX77675_SFT_CTRL_SHIFT 0
+
+/* INT_GLBL (0x02) bit bits and shifts */
+#define MAX77675_INT_SBB3_F_BIT BIT(7)
+#define MAX77675_INT_SBB3_F_SHIFT 7
+#define MAX77675_INT_SBB2_F_BIT BIT(6)
+#define MAX77675_INT_SBB2_F_SHIFT 6
+#define MAX77675_INT_SBB1_F_BIT BIT(5)
+#define MAX77675_INT_SBB1_F_SHIFT 5
+#define MAX77675_INT_SBB0_F_BIT BIT(4)
+#define MAX77675_INT_SBB0_F_SHIFT 4
+#define MAX77675_INT_TJAL2_R_BIT BIT(3)
+#define MAX77675_INT_TJAL2_R_SHIFT 3
+#define MAX77675_INT_TJAL1_R_BIT BIT(2)
+#define MAX77675_INT_TJAL1_R_SHIFT 2
+#define MAX77675_INT_EN_R_BIT BIT(1)
+#define MAX77675_INT_EN_R_SHIFT 1
+#define MAX77675_INT_EN_F_BIT BIT(0)
+#define MAX77675_INT_EN_F_SHIFT 0
+
+/* INTM_GLBL (0x03) bits and shifts */
+#define MAX77675_INTM_SBB3_F_BIT BIT(7)
+#define MAX77675_INTM_SBB3_F_SHIFT 7
+#define MAX77675_INTM_SBB2_F_BIT BIT(6)
+#define MAX77675_INTM_SBB2_F_SHIFT 6
+#define MAX77675_INTM_SBB1_F_BIT BIT(5)
+#define MAX77675_INTM_SBB1_F_SHIFT 5
+#define MAX77675_INTM_SBB0_F_BIT BIT(4)
+#define MAX77675_INTM_SBB0_F_SHIFT 4
+#define MAX77675_INTM_TJAL2_R_BIT BIT(3)
+#define MAX77675_INTM_TJAL2_R_SHIFT 3
+#define MAX77675_INTM_TJAL1_R_BIT BIT(2)
+#define MAX77675_INTM_TJAL1_R_SHIFT 2
+#define MAX77675_INTM_EN_R_BIT BIT(1)
+#define MAX77675_INTM_EN_R_SHIFT 1
+#define MAX77675_INTM_EN_F_BIT BIT(0)
+#define MAX77675_INTM_EN_F_SHIFT 0
+
+/* STAT_GLBL (0x04) bits and shifts */
+#define MAX77675_STAT_SBB3_S_BIT BIT(7)
+#define MAX77675_STAT_SBB3_S_SHIFT 7
+#define MAX77675_STAT_SBB2_S_BIT BIT(6)
+#define MAX77675_STAT_SBB2_S_SHIFT 6
+#define MAX77675_STAT_SBB1_S_BIT BIT(5)
+#define MAX77675_STAT_SBB1_S_SHIFT 5
+#define MAX77675_STAT_SBB0_S_BIT BIT(4)
+#define MAX77675_STAT_SBB0_S_SHIFT 4
+#define MAX77675_STAT_TJAL2_S_BIT BIT(2)
+#define MAX77675_STAT_TJAL2_S_SHIFT 2
+#define MAX77675_STAT_TJAL1_S_BIT BIT(1)
+#define MAX77675_STAT_TJAL1_S_SHIFT 1
+#define MAX77675_STAT_STAT_EN_BIT BIT(0)
+#define MAX77675_STAT_STAT_EN_SHIFT 0
+
+#define MAX77675_STAT_STAT_EN_BIT BIT(0)
+#define MAX77675_STAT_STAT_EN_SHIFT 0
+
+/* ERCFLAG (0x05) bits and shifts */
+#define MAX77675_SFT_CRST_F_BIT BIT(5) /* Software Cold Reset Flag */
+#define MAX77675_SFT_CRST_F_SHIFT 5
+#define MAX77675_SFT_OFF_F_BIT BIT(4) /* Software Off Flag */
+#define MAX77675_SFT_OFF_F_SHIFT 4
+#define MAX77675_MRST_BIT BIT(3) /* Manual Reset Timer Flag */
+#define MAX77675_MRST_SHIFT 3
+#define MAX77675_UVLO_BIT BIT(2) /* Undervoltage Lockout Flag */
+#define MAX77675_UVLO_SHIFT 2
+#define MAX77675_OVLO_BIT BIT(1) /* Overvoltage Lockout Flag */
+#define MAX77675_OVLO_SHIFT 1
+#define MAX77675_TOVLD_BIT BIT(0) /* Thermal Overload Flag */
+#define MAX77675_TOVLD_SHIFT 0
+
+/* CID (0x06) bits and shifts */
+#define MAX77675_CID_MASK GENMASK(4, 0) /* Chip Identification Code mask */
+#define MAX77675_CID_SHIFT 0 /* Starts at bit 0 */
+
+/* CNFG_SBB_TOP_A (0x07) bits and shifts */
+#define MAX77675_STEP_SZ_SBB3_BIT BIT(5)
+#define MAX77675_STEP_SZ_SBB3_SHIFT 5
+#define MAX77675_STEP_SZ_SBB2_BIT BIT(4)
+#define MAX77675_STEP_SZ_SBB2_SHIFT 4
+#define MAX77675_STEP_SZ_SBB1_BIT BIT(3)
+#define MAX77675_STEP_SZ_SBB1_SHIFT 3
+#define MAX77675_STEP_SZ_SBB0_BIT BIT(2)
+#define MAX77675_STEP_SZ_SBB0_SHIFT 2
+#define MAX77675_DRV_SBB_MASK GENMASK(1, 0)
+#define MAX77675_DRV_SBB_SHIFT 0
+
+/* CNFG_SBB0_A (0x08) bits and shifts */
+#define MAX77675_TV_SBB0_MASK GENMASK(7, 0)
+#define MAX77675_TV_SBB0_SHIFT 0
+
+/* CNFG_SBB0_B (0x09) bits and shifts */
+#define MAX77675_ADE_SBB0_BIT BIT(3)
+#define MAX77675_ADE_SBB0_SHIFT 3
+#define MAX77675_EN_SBB0_MASK GENMASK(2, 0)
+#define MAX77675_EN_SBB0_SHIFT 0
+
+/* CNFG_SBB1_A (0x0A) bits and shifts */
+#define MAX77675_TV_SBB1_MASK GENMASK(7, 0)
+#define MAX77675_TV_SBB1_SHIFT 0
+
+/* CNFG_SBB1_B (0x0B) bits and shifts */
+#define MAX77675_ADE_SBB1_BIT BIT(3)
+#define MAX77675_ADE_SBB1_SHIFT 3
+#define MAX77675_EN_SBB1_MASK GENMASK(2, 0)
+#define MAX77675_EN_SBB1_SHIFT 0
+
+/* CNFG_SBB2_A (0x0C) bits and shifts */
+#define MAX77675_TV_SBB2_MASK GENMASK(7, 0)
+#define MAX77675_TV_SBB2_SHIFT 0
+
+/* CNFG_SBB2_B (0x0D) bits and shifts */
+#define MAX77675_ADE_SBB2_BIT BIT(3)
+#define MAX77675_ADE_SBB2_SHIFT 3
+#define MAX77675_EN_SBB2_MASK GENMASK(2, 0)
+#define MAX77675_EN_SBB2_SHIFT 0
+
+/* CNFG_SBB3_A (0x0E) bits and shifts */
+#define MAX77675_TV_SBB3_MASK GENMASK(7, 0)
+#define MAX77675_TV_SBB3_SHIFT 0
+
+/* CNFG_SBB3_B (0x0F) bits and shifts */
+#define MAX77675_ADE_SBB3_BIT BIT(3)
+#define MAX77675_ADE_SBB3_SHIFT 3
+#define MAX77675_EN_SBB3_MASK GENMASK(2, 0)
+#define MAX77675_EN_SBB3_SHIFT 0
+
+#define MAX77675_EN_SBB_MASK GENMASK(2, 0)
+
+/* CNFG_SBB_TOP_B (0x10) bits and shifts */
+#define MAX77675_DVS_SLEW_BIT BIT(5)
+#define MAX77675_DVS_SLEW_SHIFT 5
+#define MAX77675_LAT_MODE_BIT BIT(4)
+#define MAX77675_LAT_MODE_SHIFT 4
+#define MAX77675_SR_SBB3_BIT BIT(3)
+#define MAX77675_SR_SBB3_SHIFT 3
+#define MAX77675_SR_SBB2_BIT BIT(2)
+#define MAX77675_SR_SBB2_SHIFT 2
+#define MAX77675_SR_SBB1_BIT BIT(1)
+#define MAX77675_SR_SBB1_SHIFT 1
+#define MAX77675_SR_SBB0_BIT BIT(0)
+#define MAX77675_SR_SBB0_SHIFT 0
+
+#define MAX77675_MAX_REGISTER 0x10
+
+/* Common minimum voltage (in microvolts) */
+#define MAX77675_MIN_UV 500000 // 500 mV
+
+/* Voltage step configuration for 25mV mode */
+#define MAX77675_STEP_25MV 25000 // Step size: 25 mV
+#define MAX77675_MAX_UV_25MV 5500000 // Max voltage: 5.5 V
+#define MAX77675_NUM_LEVELS_25MV 201 // levels = (5500mV - 500mV) / 25mV + 1
+
+/* Voltage step configuration for 12.5mV mode */
+#define MAX77675_STEP_12_5MV 12500 // Step size: 12.5 mV
+#define MAX77675_MAX_UV_12_5MV 3687500 // Max voltage: 3.6875 V
+#define MAX77675_NUM_LEVELS_12_5MV 255 // levels = (3687.5mV - 500mV) / 12.5mV + 1
+
+#define MAX77675_ENABLE_MASK 0x07
+#define MAX77675_ENABLE_OFF 0x04
+#define MAX77675_ENABLE_ON 0x06
+
+#define MAX77675_REGULATOR_AD_MASK BIT(3)
+#define MAX77675_REGULATOR_AD_OFF 0x00
+#define MAX77675_REGULATOR_AD_ON BIT(3)
+
+/* Regulator ID enumeration */
+enum max77675_regulator_id {
+ MAX77675_ID_SBB0 = 0,
+ MAX77675_ID_SBB1,
+ MAX77675_ID_SBB2,
+ MAX77675_ID_SBB3,
+ MAX77675_ID_NUM_MAX,
+};
+
+struct max77675_irq_status {
+ bool sbb3_fault;
+ bool sbb2_fault;
+ bool sbb1_fault;
+ bool sbb0_fault;
+ bool tjal2_rising;
+ bool tjal1_rising;
+ bool nen_rising;
+ bool nen_falling;
+};
+
+struct max77675_status {
+ bool sbb3_overload;
+ bool sbb2_overload;
+ bool sbb1_overload;
+ bool sbb0_overload;
+ bool tjal2_status;
+ bool tjal1_status;
+ bool nen_status;
+};
+
+struct max77675_ercf_status {
+ bool sft_crst_f;
+ bool sft_off_f;
+ bool mrst;
+ bool uvlo;
+ bool ovlo;
+ bool tovld;
+};
+
+#endif /* __MAX77675_REG_H__ */
--
2.34.1
^ permalink raw reply related [flat|nested] 7+ messages in thread