[PATCH v3 1/6] riscv: dts: spacemit: k1-musepi-pro: add PMIC and power infrastructure

[PATCH v3 1/6] riscv: dts: spacemit: k1-musepi-pro: add PMIC and power infrastructure

[Andre Heider]

Enable i2c8 and add the connected SpacemiT P1 PMIC with its related regulators
for the board's power infrastructure and voltage regulation support.

Signed-off-by: Andre Heider <a.heider@gmail.com>
---
 .../riscv/boot/dts/spacemit/k1-musepi-pro.dts | 134 ++++++++++++++++++
 1 file changed, 134 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
index 29e333b670cf0..e0b585c50014b 100644
--- a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
@@ -17,6 +17,7 @@ / {
 	aliases {
 		ethernet0 = &eth0;
 		serial0 = &uart0;
+		i2c8 = &i2c8;
 	};
 
 	chosen {
@@ -33,6 +34,15 @@ led1 {
 			default-state = "on";
 		};
 	};
+
+	reg_vcc_4v0: regulator-vcc-4v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC4V0";
+		regulator-min-microvolt = <4000000>;
+		regulator-max-microvolt = <4000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
 };
 
 &emmc {
@@ -72,6 +82,130 @@ &pdma {
 	status = "okay";
 };
 
+&i2c8 {
+	pinctrl-0 = <&i2c8_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	pmic@41 {
+		compatible = "spacemit,p1";
+		reg = <0x41>;
+		interrupts = <64>;
+		vin1-supply = <&reg_vcc_4v0>;
+		vin2-supply = <&reg_vcc_4v0>;
+		vin3-supply = <&reg_vcc_4v0>;
+		vin4-supply = <&reg_vcc_4v0>;
+		vin5-supply = <&reg_vcc_4v0>;
+		vin6-supply = <&reg_vcc_4v0>;
+		aldoin-supply = <&reg_vcc_4v0>;
+		dldoin1-supply = <&buck5>;
+		dldoin2-supply = <&buck5>;
+
+		regulators {
+			buck1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck3_1v8: buck3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck4_3v3: buck4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck5: buck5 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			buck6 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3450000>;
+				regulator-ramp-delay = <5000>;
+				regulator-always-on;
+			};
+
+			aldo1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+			};
+
+			aldo2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			aldo3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			aldo4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo1 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-boot-on;
+			};
+
+			dldo2 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo3 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo4 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-always-on;
+			};
+
+			dldo5 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+
+			dldo6 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+				regulator-always-on;
+			};
+
+			dldo7 {
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <3400000>;
+			};
+		};
+	};
+};
+
 &uart0 {
 	pinctrl-0 = <&uart0_2_cfg>;
 	pinctrl-names = "default";
-- 
2.53.0

[PATCH v3 2/6] riscv: dts: spacemit: k1-musepi-pro: add 24c02 eeprom

[Andre Heider]

Enable i2c2 and add the connected GT24C02B EEPROM.

It contains an ONIE TLV table:
=> tlv_eeprom
TLV: 0
[  12.162] TlvInfo Header:
[  12.162]    Id String:    TlvInfo
[  12.165]    Version:      1
[  12.168]    Total Length: 58
[  12.171] TLV Name             Code Len Value
[  12.175] -------------------- ---- --- -----
[  12.179] Product Name         0x21  16 k1-x_MUSE-Pi-Pro
[  12.184] Serial Number        0x23  17 BPMIMXXXXXXXXXXXX
[  12.189] Unknown              0x41   1  0x02
[  12.194] Base MAC Address     0x24   6 FE:FE:FE:XX:XX:XX
[  12.199] MAC Addresses        0x2A   2 2
[  12.203] CRC-32               0xFE   4 0x395ECD34
[  12.207] Checksum is valid.

(With 0x41 as TLV_CODE_DDR_CSNUM)

Signed-off-by: Andre Heider <a.heider@gmail.com>
---
 .../riscv/boot/dts/spacemit/k1-musepi-pro.dts | 33 +++++++++++++++++++
 1 file changed, 33 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
index e0b585c50014b..41d7d6d20a797 100644
--- a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
@@ -17,6 +17,7 @@ / {
 	aliases {
 		ethernet0 = &eth0;
 		serial0 = &uart0;
+		i2c2 = &i2c2;
 		i2c8 = &i2c8;
 	};
 
@@ -82,6 +83,38 @@ &pdma {
 	status = "okay";
 };
 
+&i2c2 {
+	pinctrl-0 = <&i2c2_0_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	eeprom@50 {
+		compatible = "atmel,24c02";
+		reg = <0x50>;
+		vcc-supply = <&buck3_1v8>; /* EEPROM_VCC1V8 */
+		pagesize = <8>;
+		read-only;
+		size = <256>;
+
+		nvmem-layout {
+			compatible = "onie,tlv-layout";
+
+			product-name {
+			};
+
+			serial-number {
+			};
+
+			mac-address {
+				#nvmem-cell-cells = <1>;
+			};
+
+			num-macs {
+			};
+		};
+	};
+};
+
 &i2c8 {
 	pinctrl-0 = <&i2c8_cfg>;
 	pinctrl-names = "default";
-- 
2.53.0

[PATCH v3 3/6] riscv: dts: spacemit: k1-musepi-pro: enable QSPI and add SPI NOR

[Andre Heider]

Add the QSPI controller node and describe the attached SPI NOR flash
(Winbond W25Q64FWSSAQ).

Add a corresponding vendor flash partition layout.

Signed-off-by: Andre Heider <a.heider@gmail.com>
---
 .../riscv/boot/dts/spacemit/k1-musepi-pro.dts | 50 +++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
index 41d7d6d20a797..b0f66f49db4b7 100644
--- a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
@@ -44,6 +44,15 @@ reg_vcc_4v0: regulator-vcc-4v0 {
 		regulator-boot-on;
 		regulator-always-on;
 	};
+
+	reg_qspi_vcc1v833: regulator-qspi-vcc1v833 {
+		compatible = "regulator-fixed";
+		regulator-name = "QSPI_VCC1833";
+		regulator-min-microvolt = <1833000>;
+		regulator-max-microvolt = <1833000>;
+		regulator-always-on;
+		vin-supply = <&buck4_3v3>;
+	};
 };
 
 &emmc {
@@ -239,6 +248,47 @@ dldo7 {
 	};
 };
 
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&qspi_cfg>;
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <26500000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+		vcc-supply = <&reg_qspi_vcc1v833>;
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			bootinfo@0 {
+				reg = <0x0 0x10000>;
+			};
+			private@10000 {
+				reg = <0x10000 0x10000>;
+			};
+			fsbl@20000 {
+				reg = <0x20000 0x40000>;
+			};
+			env@60000 {
+				reg = <0x60000 0x10000>;
+			};
+			opensbi@70000 {
+				reg = <0x70000 0x30000>;
+			};
+			uboot@a0000 {
+				reg = <0xa0000 0x760000>;
+			};
+		};
+	};
+};
+
 &uart0 {
 	pinctrl-0 = <&uart0_2_cfg>;
 	pinctrl-names = "default";
-- 
2.53.0

[PATCH v3 4/6] riscv: dts: spacemit: k1-musepi-pro: enable USB 3 ports

[Andre Heider]

Enable the DWC3 USB 3.0 controller, its associated combo_phy (USB 3 PHY)
and usbphy2 (USB 2 PHY) on the MusePi Pro board.

The board uses a VLI VL817 hub, providing four ports.

Signed-off-by: Andre Heider <a.heider@gmail.com>
---
 .../riscv/boot/dts/spacemit/k1-musepi-pro.dts | 52 +++++++++++++++++++
 1 file changed, 52 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
index b0f66f49db4b7..b24b378b1b220 100644
--- a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
@@ -53,6 +53,26 @@ reg_qspi_vcc1v833: regulator-qspi-vcc1v833 {
 		regulator-always-on;
 		vin-supply = <&buck4_3v3>;
 	};
+
+	reg_5v_vbus: regulator-5v-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_VBUS";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		gpio = <&gpio K1_GPIO(79) GPIO_ACTIVE_HIGH>; /* USB3_PWREN */
+		enable-active-high;
+	};
+
+	reg_vcc5v_hub: regulator-vcc5v-hub {
+		compatible = "regulator-fixed";
+		regulator-name = "VCC5V0_HUB";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-always-on;
+		gpio = <&gpio K1_GPIO(127) GPIO_ACTIVE_HIGH>; /* HUB_PWREN */
+		enable-active-high;
+	};
 };
 
 &emmc {
@@ -65,6 +85,10 @@ &emmc {
 	status = "okay";
 };
 
+&combo_phy {
+	status = "okay";
+};
+
 &eth0 {
 	phy-handle = <&rgmii0>;
 	phy-mode = "rgmii-id";
@@ -294,3 +318,31 @@ &uart0 {
 	pinctrl-names = "default";
 	status = "okay";
 };
+
+&usbphy2 {
+	status = "okay";
+};
+
+&usb_dwc3 {
+	dr_mode = "host";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	vbus-supply = <&reg_5v_vbus>;
+	status = "okay";
+
+	hub_2_0: hub@1 {
+		compatible = "usb2109,2817";
+		reg = <0x1>;
+		vdd-supply = <&reg_vcc5v_hub>;
+		peer-hub = <&hub_3_0>;
+		reset-gpios = <&gpio K1_GPIO(123) GPIO_ACTIVE_LOW>; /* HUB_RST */
+	};
+
+	hub_3_0: hub@2 {
+		compatible = "usb2109,817";
+		reg = <0x2>;
+		vdd-supply = <&reg_vcc5v_hub>;
+		peer-hub = <&hub_2_0>;
+		reset-gpios = <&gpio K1_GPIO(123) GPIO_ACTIVE_LOW>; /* HUB_RST */
+	};
+};
-- 
2.53.0

[PATCH v3 5/6] riscv: dts: spacemit: k1-musepi-pro: enable PCIe ports

[Andre Heider]

Enable the two PCIe controllers along with their associated PHYs. They
are routed to the M.2 M-key connector and to the PCIe slot.

Signed-off-by: Andre Heider <a.heider@gmail.com>
---
 .../riscv/boot/dts/spacemit/k1-musepi-pro.dts | 38 +++++++++++++++++++
 1 file changed, 38 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
index b24b378b1b220..953c0ff6a0d34 100644
--- a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
@@ -36,6 +36,14 @@ led1 {
 		};
 	};
 
+	reg_pcie_vcc_3v3: regulator-pcie-vcc3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "PCIE_VCC3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
 	reg_vcc_4v0: regulator-vcc-4v0 {
 		compatible = "regulator-fixed";
 		regulator-name = "VCC4V0";
@@ -272,6 +280,36 @@ dldo7 {
 	};
 };
 
+&pcie1_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie1_3_cfg>;
+	status = "okay";
+};
+
+&pcie1_port {
+	phys = <&pcie1_phy>;
+	vpcie3v3-supply = <&reg_pcie_vcc_3v3>;
+};
+
+&pcie1 {
+	status = "okay";
+};
+
+&pcie2_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie2_4_cfg>;
+	status = "okay";
+};
+
+&pcie2_port {
+	phys = <&pcie2_phy>;
+	vpcie3v3-supply = <&reg_pcie_vcc_3v3>;
+};
+
+&pcie2 {
+	status = "okay";
+};
+
 &qspi {
 	pinctrl-names = "default";
 	pinctrl-0 = <&qspi_cfg>;
-- 
2.53.0

[PATCH v3 6/6] riscv: dts: spacemit: k1-musepi-pro: set default console baud rate

[Andre Heider]

Allow serial output with the same uboot/opensbi settings so the
console works without providing a cmdline.

Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Yixun Lan <dlan@kernel.org>
---
 arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
index 953c0ff6a0d34..ce7caf6950dc0 100644
--- a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
@@ -22,7 +22,7 @@ aliases {
 	};
 
 	chosen {
-		stdout-path = "serial0";
+		stdout-path = "serial0:115200n8";
 	};
 
 	leds {
-- 
2.53.0

Re: [PATCH v3 1/6] riscv: dts: spacemit: k1-musepi-pro: add PMIC and power infrastructure

[Yixun Lan]

On 09:19 Wed 13 May     , Andre Heider wrote:
> Enable i2c8 and add the connected SpacemiT P1 PMIC with its related regulators
got a warning here, commit message should limit to 75 characters..

> for the board's power infrastructure and voltage regulation support.
> 
> Signed-off-by: Andre Heider <a.heider@gmail.com>

-- 
Yixun Lan (dlan)

Re: [PATCH v3 1/6] riscv: dts: spacemit: k1-musepi-pro: add PMIC and power infrastructure

[Yixun Lan]

Hi Andre,

On 09:19 Wed 13 May     , Andre Heider wrote:
> Enable i2c8 and add the connected SpacemiT P1 PMIC with its related regulators
> for the board's power infrastructure and voltage regulation support.
> 
> Signed-off-by: Andre Heider <a.heider@gmail.com>
> ---
>  .../riscv/boot/dts/spacemit/k1-musepi-pro.dts | 134 ++++++++++++++++++
>  1 file changed, 134 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
> index 29e333b670cf0..e0b585c50014b 100644
> --- a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
> +++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
> @@ -17,6 +17,7 @@ / {
>  	aliases {
>  		ethernet0 = &eth0;
>  		serial0 = &uart0;
> +		i2c8 = &i2c8;
>  	};
>  
>  	chosen {
> @@ -33,6 +34,15 @@ led1 {
>  			default-state = "on";
>  		};
>  	};
> +
..
> +	reg_vcc_4v0: regulator-vcc-4v0 {
I prefer to keep this name same as other boards, so let's change it
to reg_vcc_4v ..

> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC4V0";
> +		regulator-min-microvolt = <4000000>;
> +		regulator-max-microvolt = <4000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +	};
>  };

-- 
Yixun Lan (dlan)