[PATCH v2 0/2] drm/bridge: lt9211: Add drive-strength-microamp DT property

[PATCH v2 0/2] drm/bridge: lt9211: Add drive-strength-microamp DT property

[Boerge Struempfel]

The LT9211 LVDS TX output driver current is currently hardcoded to
0x8 (~25 uA). Some board layouts require a different drive strength
to meet signal integrity requirements.

This series adds support for the standard 'drive-strength-microamp'
DT property, allowing board DTs to select one of sixteen discrete
current levels between 12 uA and 36 uA. The default preserves the
existing behaviour.

Changes in v2:
- Use u8 instead of u32 for the lookup table array (values fit in u8)
- Warn when drive-strength-microamp exists in DT but is malformed

Link to v1: https://lore.kernel.org/dri-devel/20260512164609.3390700-1-bstruempfel@data-modul.com/

Boerge Struempfel (2):
  dt-bindings: display/bridge: lt9211: Add drive-strength-microamp
    property
  drm/bridge: lt9211: Add drive-strength-microamp DT property

 .../display/bridge/lontium,lt9211.yaml        |  7 +++++
 drivers/gpu/drm/bridge/lontium-lt9211.c       | 31 ++++++++++++++++++-
 2 files changed, 37 insertions(+), 1 deletion(-)

-- 
2.54.0

[PATCH v2 1/2] dt-bindings: display/bridge: lt9211: Add drive-strength-microamp property

[Boerge Struempfel]

Add the 'drive-strength-microamp' property to allow board DTs to
configure the LT9211 LVDS TX output driver current. Sixteen discrete
levels are supported, ranging from 12 uA to 36 uA. Defaults to 25 uA.

Signed-off-by: Boerge Struempfel <bstruempfel@data-modul.com>
Acked-by: Conor Dooley <conor.dooley@microchip.com>

---
 .../devicetree/bindings/display/bridge/lontium,lt9211.yaml | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/bridge/lontium,lt9211.yaml b/Documentation/devicetree/bindings/display/bridge/lontium,lt9211.yaml
index 9a6e9b25d14a..381b69c761b8 100644
--- a/Documentation/devicetree/bindings/display/bridge/lontium,lt9211.yaml
+++ b/Documentation/devicetree/bindings/display/bridge/lontium,lt9211.yaml
@@ -31,6 +31,13 @@ properties:
   vccio-supply:
     description: Regulator for 1.8V IO power.
 
+  drive-strength-microamp:
+    description:
+      LVDS TX output driver current. Sixteen discrete levels are supported,
+      corresponding to the following nominal values in microamps.
+    enum: [12, 14, 16, 17, 19, 20, 22, 23, 25, 27, 28, 30, 31, 33, 34, 36]
+    default: 25
+
   ports:
     $ref: /schemas/graph.yaml#/properties/ports
 
-- 
2.54.0

[PATCH v2 2/2] drm/bridge: lt9211: Add drive-strength-microamp DT property

[Boerge Struempfel]

The LT9211 LVDS TX output driver current (RG_MLTX_HSDRV_ISEL) was
previously hardcoded to 0x8 (~25 uA), which may not be optimal for all
board layouts.

The hardware supports 16 discrete current levels starting at 12.5 uA
with a step of 1.5625 uA. These are exposed as rounded integer microamp
values in the lookup table.

Add support for the 'drive-strength-microamp' DT property. A lookup
table maps the sixteen supported microamp values (12..36 uA) to the
corresponding register field. Defaults to 25 uA when the property is
absent, preserving the existing behaviour.

Signed-off-by: Boerge Struempfel <bstruempfel@data-modul.com>
---
 drivers/gpu/drm/bridge/lontium-lt9211.c | 31 ++++++++++++++++++++++++-
 1 file changed, 30 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/bridge/lontium-lt9211.c b/drivers/gpu/drm/bridge/lontium-lt9211.c
index 03fc8fd10f20..5edd2d2e3da6 100644
--- a/drivers/gpu/drm/bridge/lontium-lt9211.c
+++ b/drivers/gpu/drm/bridge/lontium-lt9211.c
@@ -40,6 +40,11 @@
 /* DSI lane count - 0 means 4 lanes ; 1, 2, 3 means 1, 2, 3 lanes. */
 #define REG_DSI_LANE_COUNT(n)			((n) & 3)
 
+/* Maps register value (index) to drive-strength-microamp DT property value */
+static const u8 lt9211_hsdrv_microamp[] = {
+	12, 14, 16, 17, 19, 20, 22, 23, 25, 27, 28, 30, 31, 33, 34, 36
+};
+
 struct lt9211 {
 	struct drm_bridge		bridge;
 	struct device			*dev;
@@ -50,6 +55,7 @@ struct lt9211 {
 	struct regulator		*vccio;
 	bool				lvds_dual_link;
 	bool				lvds_dual_link_even_odd_swap;
+	u8				lvds_hsdrv_isel;
 };
 
 static const struct regmap_range lt9211_rw_ranges[] = {
@@ -374,7 +380,8 @@ static int lt9211_configure_tx(struct lt9211 *ctx, bool jeida,
 		/* BIT(7) is LVDS dual-port */
 		{ 0x823b, 0x38 | (ctx->lvds_dual_link ? BIT(7) : 0) },
 		{ 0x823e, 0x92 },
-		{ 0x823f, 0x48 },
+		/* bits 3:0: RG_MLTX_HSDRV_ISEL, LVDS TX driver current */
+		{ 0x823f, 0x40 | ctx->lvds_hsdrv_isel },
 		{ 0x8240, 0x31 },
 		{ 0x8243, 0x80 },
 		{ 0x8244, 0x00 },
@@ -629,7 +636,9 @@ static int lt9211_parse_dt(struct lt9211 *ctx)
 	struct device *dev = ctx->dev;
 	struct drm_panel *panel;
 	int dual_link;
+	u32 microamp;
 	int ret;
+	int i;
 
 	ctx->vccio = devm_regulator_get(dev, "vccio");
 	if (IS_ERR(ctx->vccio))
@@ -666,6 +675,26 @@ static int lt9211_parse_dt(struct lt9211 *ctx)
 
 	ctx->panel_bridge = panel_bridge;
 
+	ctx->lvds_hsdrv_isel = 8; /* default: 25 uA */
+	ret = of_property_read_u32(dev->of_node, "drive-strength-microamp",
+				   &microamp);
+	if (!ret) {
+		for (i = 0; i < ARRAY_SIZE(lt9211_hsdrv_microamp); i++) {
+			if (lt9211_hsdrv_microamp[i] == microamp) {
+				ctx->lvds_hsdrv_isel = i;
+				break;
+			}
+		}
+		if (i == ARRAY_SIZE(lt9211_hsdrv_microamp)) {
+			dev_err(dev, "Invalid drive-strength-microamp value %u\n",
+				microamp);
+			return -EINVAL;
+		}
+	} else if (ret != -EINVAL) {
+		dev_warn(dev, "Failed to read drive-strength-microamp: %d, using default\n",
+			 ret);
+	}
+
 	return 0;
 }
 
-- 
2.54.0

Re: [PATCH v2 1/2] dt-bindings: display/bridge: lt9211: Add drive-strength-microamp property

[Marek Vasut]

On 5/13/26 3:31 PM, Boerge Struempfel wrote:
> Add the 'drive-strength-microamp' property to allow board DTs to
> configure the LT9211 LVDS TX output driver current. Sixteen discrete
> levels are supported, ranging from 12 uA to 36 uA. Defaults to 25 uA.
> 
> Signed-off-by: Boerge Struempfel <bstruempfel@data-modul.com>
> Acked-by: Conor Dooley <conor.dooley@microchip.com>
AB goes before SoB line.

Re: [PATCH v2 2/2] drm/bridge: lt9211: Add drive-strength-microamp DT property

[Marek Vasut]

On 5/13/26 3:31 PM, Boerge Struempfel wrote:

[...]

> @@ -666,6 +675,26 @@ static int lt9211_parse_dt(struct lt9211 *ctx)
>   
>   	ctx->panel_bridge = panel_bridge;
>   
> +	ctx->lvds_hsdrv_isel = 8; /* default: 25 uA */
> +	ret = of_property_read_u32(dev->of_node, "drive-strength-microamp",
> +				   &microamp);

if (ret && ret != -EINVAL) {
   ... error handling ...
   return ret;
}

Then you won't need the if (!ret) conditional and can reduce indent.

I also wonder whether it wouldn't be better to simply bail with 
dev_err_probe() if the property is invalid, let the user know they 
should fix their DTs before it is too late.

> +	if (!ret) {
> +		for (i = 0; i < ARRAY_SIZE(lt9211_hsdrv_microamp); i++) {
> +			if (lt9211_hsdrv_microamp[i] == microamp) {
> +				ctx->lvds_hsdrv_isel = i;
> +				break;
> +			}
> +		}
> +		if (i == ARRAY_SIZE(lt9211_hsdrv_microamp)) {
> +			dev_err(dev, "Invalid drive-strength-microamp value %u\n",
> +				microamp);
> +			return -EINVAL;
> +		}

[...]

> +
>   	return 0;
>   }