From: Krzysztof Kozlowski <krzk@kernel.org>
To: Alexandre Hamamdjian <azkali.limited@gmail.com>
Cc: Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, Teguh Sobirin <teguh@sobir.in>
Subject: Re: [PATCH v2 3/3] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console
Date: Thu, 14 May 2026 14:25:16 +0200 [thread overview]
Message-ID: <20260514-free-ruby-honeybee-d5f317@quoll> (raw)
In-Reply-To: <20260511-pocketds-v2-3-299dd4247f2f@gmail.com>
On Mon, May 11, 2026 at 06:33:55PM +0700, Alexandre Hamamdjian wrote:
> + vdd_ts: vdd-ts {
? So this is not a regulator?
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_ts_en";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&tca6408 1 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
Missing blank line
...
> + vdd_fan_5v0: vdd-fan-5v0-regulator {
But this is a regulator?
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_fan_5v0";
> +
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> +
> + gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-0 = <&fan_pwr_active>;
> + pinctrl-names = "default";
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vph_pwr: regulator-vph-pwr {
So here "regulator-foo"
> + compatible = "regulator-fixed";
> + regulator-name = "vph_pwr";
> + regulator-min-microvolt = <3700000>;
> + regulator-max-microvolt = <3700000>;
> +
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + upd720201_avdd33_reg: upd720201-avdd33-regulator {
but here "foo-regulator"? Why do you have completely random naming
scheme?
> + compatible = "regulator-fixed";
> +
> + regulator-name = "upd720201_avdd33";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + vin-supply = <&vph_pwr>;
> +
> + pinctrl-0 = <&upd720201_avdd33>;
> + pinctrl-names = "default";
> + };
> +
> + upd720201_vdd10_reg: upd720201-vdd10-regulator {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "upd720201_vdd10";
> + regulator-min-microvolt = <1050000>;
> + regulator-max-microvolt = <1050000>;
> +
> + gpios = <&tlmm 13 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + vin-supply = <&vph_pwr>;
> +
> + pinctrl-0 = <&upd720201_vdd10>;
> + pinctrl-names = "default";
> + };
> +
> + upd720201_vdd33_reg: upd720201-vdd33-regulator {
> + compatible = "regulator-fixed";
> +
> + regulator-name = "upd720201_vdd33";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + vin-supply = <&vph_pwr>;
> +
> + pinctrl-0 = <&upd720201_vdd33>;
> + pinctrl-names = "default";
> + };
> +
> + pwm_fan: pwm-fan {
> + compatible = "pwm-fan";
> +
> + pinctrl-0 = <&fan_pwm_active>, <&fan_int>;
> + pinctrl-names = "default", "sleep";
> +
> + fan-supply = <&vdd_fan_5v0>;
> + pwms = <&pm8550_pwm 3 40000>;
> + interrupt-parent = <&tlmm>;
> + interrupts = <64 IRQ_TYPE_EDGE_FALLING>;
> +
> + #cooling-cells = <2>;
> + cooling-levels = <0 30 45 60 70 90 120 150>;
> + };
> +
> + wcn7850-pmu {
> + compatible = "qcom,wcn7850-pmu";
> +
> + pinctrl-0 = <&wlan_en>, <&bt_default>, <&pmk8550_sleep_clk>;
> + pinctrl-names = "default";
> +
> + wlan-enable-gpios = <&tlmm 80 GPIO_ACTIVE_HIGH>;
> + bt-enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
> +
> + vdd-supply = <&vreg_s5g_0p85>;
> + vddio-supply = <&vreg_l15b_1p8>;
> + vddaon-supply = <&vreg_s2g_0p85>;
> + vdddig-supply = <&vreg_s4e_0p95>;
> + vddrfa1p2-supply = <&vreg_s4g_1p25>;
> + vddrfa1p8-supply = <&vreg_s6g_1p86>;
> +
> + regulators {
> + vreg_pmu_rfa_cmn: ldo0 {
> + regulator-name = "vreg_pmu_rfa_cmn";
> + };
> +
> + vreg_pmu_aon_0p59: ldo1 {
> + regulator-name = "vreg_pmu_aon_0p59";
> + };
> +
> + vreg_pmu_wlcx_0p8: ldo2 {
> + regulator-name = "vreg_pmu_wlcx_0p8";
> + };
> +
> + vreg_pmu_wlmx_0p85: ldo3 {
> + regulator-name = "vreg_pmu_wlmx_0p85";
> + };
> +
> + vreg_pmu_btcmx_0p85: ldo4 {
> + regulator-name = "vreg_pmu_btcmx_0p85";
> + };
> +
> + vreg_pmu_rfa_0p8: ldo5 {
> + regulator-name = "vreg_pmu_rfa_0p8";
> + };
> +
> + vreg_pmu_rfa_1p2: ldo6 {
> + regulator-name = "vreg_pmu_rfa_1p2";
> + };
> +
> + vreg_pmu_rfa_1p8: ldo7 {
> + regulator-name = "vreg_pmu_rfa_1p8";
> + };
> +
> + vreg_pmu_pcie_0p9: ldo8 {
> + regulator-name = "vreg_pmu_pcie_0p9";
> + };
> +
> + vreg_pmu_pcie_1p8: ldo9 {
> + regulator-name = "vreg_pmu_pcie_1p8";
> + };
> + };
> + };
> +};
> +
> +&cpuss0_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + cpuss0_fan0: trip-point2 {
> + temperature = <40000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss0_fan1: trip-point3 {
> + temperature = <50000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss0_fan2: trip-point4 {
> + temperature = <60000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss0_fan3: trip-point5 {
> + temperature = <65000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss0_fan4: trip-point6 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss0_fan5: trip-point7 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss0_fan6: trip-point8 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&cpuss1_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + cpuss1_fan0: trip-point2 {
> + temperature = <40000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss1_fan1: trip-point3 {
> + temperature = <50000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss1_fan2: trip-point4 {
> + temperature = <60000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss1_fan3: trip-point5 {
> + temperature = <65000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss1_fan4: trip-point6 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss1_fan5: trip-point7 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss1_fan6: trip-point8 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&cpuss2_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + cpuss2_fan0: trip-point2 {
> + temperature = <40000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss2_fan1: trip-point3 {
> + temperature = <50000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss2_fan2: trip-point4 {
> + temperature = <60000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss2_fan3: trip-point5 {
> + temperature = <65000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss2_fan4: trip-point6 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss2_fan5: trip-point7 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss2_fan6: trip-point8 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&cpuss3_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + cpuss3_fan0: trip-point2 {
> + temperature = <40000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss3_fan1: trip-point3 {
> + temperature = <50000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss3_fan2: trip-point4 {
> + temperature = <60000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss3_fan3: trip-point5 {
> + temperature = <65000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss3_fan4: trip-point6 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss3_fan5: trip-point7 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpuss3_fan6: trip-point8 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&cpu7_top_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + cpu7_top_fan0: trip-point2 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpu7_top_fan1: trip-point3 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + cpu7_top_fan2: trip-point4 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&gpuss0_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + gpuss0_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss0_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss0_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&gpuss1_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + gpuss1_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss1_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss1_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&gpuss2_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + gpuss2_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss2_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss2_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&gpuss3_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + gpuss3_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss3_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss3_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&gpuss4_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + gpuss4_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss4_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss4_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&gpuss5_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + gpuss5_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss5_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss5_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&gpuss6_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + gpuss6_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss6_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss6_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +&gpuss7_thermal {
> + polling-delay = <200>;
> +
> + trips {
> + gpuss7_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss7_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> +
> + gpuss7_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +};
> +
> +/* DMIC 01 23 */
> +&lpass_vamacro {
> + pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
> + pinctrl-names = "default";
> + vdd-micb-supply = <&vreg_l10b_1p8>;
> + qcom,dmic-sample-rate = <4800000>;
> +};
> +
> +&apps_rsc {
> + regulators-0 {
> + compatible = "qcom,pm8550-rpmh-regulators";
> + qcom,pmic-id = "b";
> +
> + vdd-bob1-supply = <&vph_pwr>;
> + vdd-bob2-supply = <&vph_pwr>;
> + vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>;
> + vdd-l2-l13-l14-supply = <&vreg_bob1>;
> + vdd-l3-supply = <&vreg_s4g_1p25>;
> + vdd-l5-l16-supply = <&vreg_bob1>;
> + vdd-l6-l7-supply = <&vreg_bob1>;
> + vdd-l8-l9-supply = <&vreg_bob1>;
> + vdd-l11-supply = <&vreg_s4g_1p25>;
> + vdd-l12-supply = <&vreg_s6g_1p86>;
> + vdd-l15-supply = <&vreg_s6g_1p86>;
> + vdd-l17-supply = <&vreg_bob2>;
> +
> + vreg_bob1: bob1 {
> + regulator-name = "vreg_bob1";
> + regulator-min-microvolt = <3296000>;
> + regulator-max-microvolt = <3960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_bob2: bob2 {
> + regulator-name = "vreg_bob2";
> + regulator-min-microvolt = <2720000>;
> + regulator-max-microvolt = <3960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l2b_3p0: ldo2 {
> + regulator-name = "vreg_l2b_3p0";
> + regulator-min-microvolt = <3008000>;
> + regulator-max-microvolt = <3008000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l5b_3p1: ldo5 {
> + regulator-name = "vreg_l5b_3p1";
> + regulator-min-microvolt = <3104000>;
> + regulator-max-microvolt = <3104000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l6b_1p8: ldo6 {
> + regulator-name = "vreg_l6b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3008000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7b_1p8: ldo7 {
> + regulator-name = "vreg_l7b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3008000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l8b_1p8: ldo8 {
> + regulator-name = "vreg_l8b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3008000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l9b_2p9: ldo9 {
> + regulator-name = "vreg_l9b_2p9";
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <3008000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l10b_1p8: ldo10 {
> + regulator-name = "vreg_l10b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l11b_1p2: ldo11 {
> + regulator-name = "vreg_l11b_1p2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1504000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l12b_1p8: ldo12 {
> + regulator-name = "vreg_l12b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l13b_3p0: ldo13 {
> + regulator-name = "vreg_l13b_3p0";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l14b_3p2: ldo14 {
> + regulator-name = "vreg_l14b_3p2";
> + regulator-min-microvolt = <3200000>;
> + regulator-max-microvolt = <3200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l15b_1p8: ldo15 {
> + regulator-name = "vreg_l15b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l16b_2p8: ldo16 {
> + regulator-name = "vreg_l16b_2p8";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l17b_2p5: ldo17 {
> + regulator-name = "vreg_l17b_2p5";
> + regulator-min-microvolt = <2504000>;
> + regulator-max-microvolt = <2504000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-1 {
> + compatible = "qcom,pm8550vs-rpmh-regulators";
> + qcom,pmic-id = "c";
> +
> + vdd-l1-supply = <&vreg_s4g_1p25>;
> + vdd-l2-supply = <&vreg_s4e_0p95>;
> + vdd-l3-supply = <&vreg_s4e_0p95>;
> +
> + vreg_l3c_0p9: ldo3 {
> + regulator-name = "vreg_l3c_0p9";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-2 {
> + compatible = "qcom,pm8550vs-rpmh-regulators";
> + qcom,pmic-id = "d";
> +
> + vdd-l1-supply = <&vreg_s4e_0p95>;
> + vdd-l2-supply = <&vreg_s4e_0p95>;
> + vdd-l3-supply = <&vreg_s4e_0p95>;
> +
> + vreg_l1d_0p88: ldo1 {
> + regulator-name = "vreg_l1d_0p88";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <920000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-3 {
> + compatible = "qcom,pm8550vs-rpmh-regulators";
> + qcom,pmic-id = "e";
> +
> + vdd-l1-supply = <&vreg_s4e_0p95>;
> + vdd-l2-supply = <&vreg_s4e_0p95>;
> + vdd-l3-supply = <&vreg_s4g_1p25>;
> + vdd-s4-supply = <&vph_pwr>;
> + vdd-s5-supply = <&vph_pwr>;
> +
> + vreg_s4e_0p95: smps4 {
> + regulator-name = "vreg_s4e_0p95";
> + regulator-min-microvolt = <904000>;
> + regulator-max-microvolt = <984000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s5e_1p08: smps5 {
> + regulator-name = "vreg_s5e_1p08";
> + regulator-min-microvolt = <1010000>;
> + regulator-max-microvolt = <1120000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l1e_0p88: ldo1 {
> + regulator-name = "vreg_l1e_0p88";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l2e_0p9: ldo2 {
> + regulator-name = "vreg_l2e_0p9";
> + regulator-min-microvolt = <904000>;
> + regulator-max-microvolt = <970000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3e_1p2: ldo3 {
> + regulator-name = "vreg_l3e_1p2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-4 {
> + compatible = "qcom,pm8550ve-rpmh-regulators";
> + qcom,pmic-id = "f";
> +
> + vdd-l1-supply = <&vreg_s4e_0p95>;
> + vdd-l2-supply = <&vreg_s4e_0p95>;
> + vdd-l3-supply = <&vreg_s4e_0p95>;
> + vdd-s4-supply = <&vph_pwr>;
> +
> + vreg_s4f_0p5: smps4 {
> + regulator-name = "vreg_s4f_0p5";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <700000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l1f_0p9: ldo1 {
> + regulator-name = "vreg_l1f_0p9";
> + regulator-min-microvolt = <912000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l2f_0p88: ldo2 {
> + regulator-name = "vreg_l2f_0p88";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3f_0p88: ldo3 {
> + regulator-name = "vreg_l3f_0p88";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-5 {
> + compatible = "qcom,pm8550vs-rpmh-regulators";
> + qcom,pmic-id = "g";
> + vdd-l1-supply = <&vreg_s4g_1p25>;
> + vdd-l2-supply = <&vreg_s4g_1p25>;
> + vdd-l3-supply = <&vreg_s4g_1p25>;
> + vdd-s1-supply = <&vph_pwr>;
> + vdd-s2-supply = <&vph_pwr>;
> + vdd-s3-supply = <&vph_pwr>;
> + vdd-s4-supply = <&vph_pwr>;
> + vdd-s5-supply = <&vph_pwr>;
> + vdd-s6-supply = <&vph_pwr>;
> +
> + vreg_s1g_1p25: smps1 {
> + regulator-name = "vreg_s1g_1p25";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s2g_0p85: smps2 {
> + regulator-name = "vreg_s2g_0p85";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s3g_0p8: smps3 {
> + regulator-name = "vreg_s3g_0p8";
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1004000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s4g_1p25: smps4 {
> + regulator-name = "vreg_s4g_1p25";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1352000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s5g_0p85: smps5 {
> + regulator-name = "vreg_s5g_0p85";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1004000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s6g_1p86: smps6 {
> + regulator-name = "vreg_s6g_1p86";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l1g_1p2: ldo1 {
> + regulator-name = "vreg_l1g_1p2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3g_1p2: ldo3 {
> + regulator-name = "vreg_l3g_1p2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +};
> +
> +&pm8550_gpios {
> + sdc2_card_det_n: sdc2-card-det-n-state {
> + pins = "gpio12";
> + function = "normal";
> + input-enable;
> + output-disable;
> + bias-pull-up;
> + power-source = <1>;
> + };
> +
> + volume_up_n: volume-up-n-state {
> + pins = "gpio6";
> + function = "normal";
> + power-source = <1>;
> + bias-pull-up;
> + input-enable;
> + };
> +
> + fan_pwm_active: fan-pwm-active-state {
> + pins = "gpio9";
> + function = "func1";
> + output-low;
> + bias-disable;
> + power-source = <0>;
> + qcom,drive-strength = <3>; /* PMIC_GPIO_STRENGTH_LOW */
> + };
> +};
> +
> +&pmk8550_gpios {
> + pmk8550_sleep_clk: sleep-clk-state {
> + pins = "gpio3";
> + function = "func1";
> + input-disable;
> + output-enable;
> + bias-disable;
> + power-source = <0>;
> + };
> +};
> +
> +&pm8550b_eusb2_repeater {
> + vdd18-supply = <&vreg_l15b_1p8>;
> + vdd3-supply = <&vreg_l5b_3p1>;
> +};
> +
> +&pon_pwrkey {
> + status = "okay";
> +};
> +
> +&pon_resin {
> + linux,code = <KEY_VOLUMEDOWN>;
> +
> + status = "okay";
> +};
> +
> +&pmk8550_rtc {
> + nvmem-cells = <&rtc_offset>;
> + nvmem-cell-names = "offset";
> +};
> +
> +&pmk8550_sdam_2 {
> + rtc_offset: rtc-offset@bc {
> + reg = <0xbc 0x4>;
> + };
> +};
> +
> +&qupv3_id_0 {
> + status = "okay";
> +};
> +
> +&qupv3_id_1 {
> + status = "okay";
> +
> + /* AYANEO Controller serial interface */
> + uart11: serial@88c000 {
Why isn't this part of the SoC?
> + compatible = "qcom,geni-uart";
> + reg = <0 0x0088c000 0 0x4000>;
DTS should not define SoC components. How do you exactly see that
happening during assembly of SoC on the board?
> + clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
> + clock-names = "se";
> + pinctrl-0 = <&qup_uart11_default>;
> + pinctrl-names = "default";
> + interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH 0>;
> + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
> + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
> + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
> + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ACTIVE_ONLY>;
> + interconnect-names = "qup-core", "qup-config";
> + operating-points-v2 = <&qup_opp_table_100mhz>;
> + power-domains = <&rpmhpd RPMHPD_CX>;
> +
> + status = "okay";
> + };
> +};
> +
> +&remoteproc_adsp {
> + firmware-name = "qcom/sm8550/ayaneo/adsp.mdt",
> + "qcom/sm8550/ayaneo/adsp_dtb.mdt";
> +
> + status = "okay";
> +};
> +
> +&sdhc_2 {
> + cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
> + pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
> + pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
> + pinctrl-names = "default", "sleep";
> + vmmc-supply = <&vreg_l9b_2p9>;
> + vqmmc-supply = <&vreg_l8b_1p8>;
> + no-sdio;
> + no-mmc;
> +
> + sd-uhs-sdr12;
> + sd-uhs-sdr25;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + sd-uhs-ddr50;
> +
> + qcom,dll-config = <0x0007442c>;
> + sdhci-caps-mask = <0x3 0x0>;
> +
> + status = "okay";
> +};
> +
> +&sleep_clk {
> + clock-frequency = <32764>;
> +};
> +
> +&swr0 {
> + status = "okay";
> +
> + spk_amp_l: speaker@0,0 {
> + compatible = "sdw20217020400";
> + reg = <0 0>;
> +
> + pinctrl-0 = <&spkr_1_sd_n_active>;
> + pinctrl-names = "default";
> +
> + powerdown-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
> +
> + vdd-1p8-supply = <&vreg_l10b_1p8>;
> + vdd-io-supply = <&vreg_l10b_1p8>;
> +
> + #sound-dai-cells = <0>;
> + sound-name-prefix = "SpkrLeft";
> + qcom,port-mapping = <1 2 3 7 10 13>;
> + };
> +
> + spk_amp_r: speaker@0,1 {
> + compatible = "sdw20217020400";
> + reg = <0 1>;
> +
> + pinctrl-0 = <&spkr_2_sd_n_active>;
> + pinctrl-names = "default";
> +
> + powerdown-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
> +
> + vdd-1p8-supply = <&vreg_l10b_1p8>;
> + vdd-io-supply = <&vreg_l10b_1p8>;
> +
> + #sound-dai-cells = <0>;
> + sound-name-prefix = "SpkrRight";
> + qcom,port-mapping = <4 5 6 7 11 13>;
> + };
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <32 4>;
> +
> + bt_default: bt-default-state {
> + bt-en-pins {
> + pins = "gpio81";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + sw-ctrl-pins {
> + pins = "gpio82";
> + function = "gpio";
> + bias-pull-down;
> + };
> + };
> +
> + fan_pwr_active: fan-pwr-active-state {
> + pins = "gpio31";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + output-low;
> + };
> +
> + fan_int: fan-int-state {
> + pins = "gpio64";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + upd720201_avdd33: upd720201-avdd33-state {
> + pins = "gpio10";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + upd720201_vdd10: upd720201-vdd10-state {
> + pins = "gpio13";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + upd720201_vdd33: upd720201-vdd33-state {
> + pins = "gpio18";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + gamepad_pwr_en: gamepad-pwr-en-active-state {
> + pins = "gpio52";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + output-high;
> + };
> +
> + qup_uart11_default: qup-uart11-default-state {
> + /* TX, RX */
> + pins = "gpio70", "gpio71";
> + function = "qup2_se3";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + sde_dsi_active: sde-dsi-active-state {
> + pins = "gpio133";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-disable;
> + output-high;
> + };
> +
> + sde_dsi_suspend: sde-dsi-suspend-state {
> + pins = "gpio133";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + sde_te_active: sde-te-active-state {
> + pins = "gpio86";
> + function = "mdp_vsync";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + sde_te_suspend: sde-te-suspend-state {
> + pins = "gpio86";
> + function = "mdp_vsync";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + wlan_en: wlan-en-state {
> + pins = "gpio80";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> +
> + spkr_1_sd_n_active: spkr-1-sd-n-active-state {
> + pins = "gpio7";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + output-high;
> + };
> +
> + spkr_2_sd_n_active: spkr-2-sd-n-active-state {
> + pins = "gpio12";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + output-high;
> + };
> +
> + panel_pwr_active: panel-pwr-active-state {
> + pins = "gpio152", "gpio153";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-disable;
> + output-high;
> + };
> +
> + sde_dsi1_active: sde-dsi1-active-state {
> + pins = "gpio137";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-disable;
> + output-high;
> + };
> +
> + sde_dsi1_suspend: sde-dsi1-suspend-state {
> + pins = "gpio137";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + ts_rst_default: ts-rst-default-state {
> + pins = "gpio24";
> + function = "gpio";
> + bias-pull-up;
> + drive-strength = <8>;
> + };
> +
> + ts_rst_sleep: ts-rst-sleep-state {
> + pins = "gpio24";
> + function = "gpio";
> + bias-pull-down;
> + drive-strength = <2>;
> + };
> +
> + ts_int_default: ts-int-default-state {
> + pins = "gpio25";
> + function = "gpio";
> + bias-pull-up;
> + drive-strength = <8>;
> + };
> +
> + ts_int_sleep: ts-int-sleep-state {
> + pins = "gpio25";
> + function = "gpio";
> + bias-pull-down;
> + drive-strength = <2>;
> + };
> +
> + ts2_irq: ts2-irq-state {
> + pins = "gpio39";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-disable;
> + };
> +
> + ts2_reset: ts2-reset-state {
> + pins = "gpio38";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> +};
> +
> +&pm8550_pwm {
> + status = "okay";
> +};
> +
> +&xo_board {
> + clock-frequency = <76800000>;
> +};
> +
> +&gpi_dma1 {
> + status = "okay";
> +};
> +
> +&gpi_dma2 {
> + status = "okay";
> +};
> +
> +&gpu {
> + status = "okay";
> +};
> +
> +&gpu_zap_shader {
> + firmware-name = "qcom/sm8550/a740_zap.mbn";
> +};
> +
> +&gpu_opp_table {
> + opp-719000000 {
> + opp-hz = /bits/ 64 <719000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
> + opp-peak-kBps = <10687500>; // Level 7
> + qcom,opp-acd-level = <0x882e5ffd>;
> + };
> +
> + opp-746000000 {
> + opp-hz = /bits/ 64 <746000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
> + opp-peak-kBps = <10687500>; // Level 7
> + qcom,opp-acd-level = <0x882e5ffd>;
> + };
> +
> + opp-794000000 {
> + opp-hz = /bits/ 64 <794000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
> + opp-peak-kBps = <14398438>; // Level 8
> + qcom,opp-acd-level = <0xa82d5ffd>;
> + };
> +
> + opp-827000000 {
> + opp-hz = /bits/ 64 <827000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
> + opp-peak-kBps = <16500000>; // Level 9
> + qcom,opp-acd-level = <0xa82d5ffd>;
> + };
> +
> + opp-860000000 {
> + opp-hz = /bits/ 64 <860000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
> + opp-peak-kBps = <16500000>; // Level 9
> + qcom,opp-acd-level = <0x882d5ffd>;
> + };
> +
> + opp-1000000000 {
> + opp-hz = /bits/ 64 <1000000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L2>;
> + opp-peak-kBps = <16500000>; // Level 9
> + qcom,opp-acd-level = <0x882d5ffd>;
> + };
> +};
> +
> +&i2c_master_hub_0 {
> + status = "okay";
> +};
> +
> +&i2c_hub_2 {
> + status = "okay";
> +
> + typec-retimer@1c {
> + compatible = "onnn,nb7vpq904m";
> + reg = <0x1c>;
> + vcc-supply = <&vreg_l15b_1p8>;
> +
> + retimer-switch;
> + orientation-switch;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + redriver_ss_out: endpoint {
> + remote-endpoint = <&pmic_glink_ss_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + redriver_ss_in: endpoint {
> + data-lanes = <3 2 1 0>;
> + remote-endpoint = <&usb_dp_qmpphy_out>;
> + };
> + };
> + };
> + };
> +};
> +
> +&mdss {
> + status = "okay";
> +};
> +
> +&mdss_dp0 {
> + status = "okay";
> +};
> +
> +&mdss_dp0_out {
> + data-lanes = <0 1 2 3>;
> +};
> +
> +&mdss_dsi0 {
> + vdda-supply = <&vreg_l3e_1p2>;
> +
> + status = "okay";
> +
> + display_panel: panel@0 {
> + reg = <0>;
> +
> + pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>;
> + pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>;
> + pinctrl-names = "default", "sleep";
> + };
> +};
> +
> +&mdss_dsi0_phy {
> + vdds-supply = <&vreg_l1e_0p88>;
> +
> + status = "okay";
> +};
> +
> +&pcie0 {
> + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
> + perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
> +
> + max-link-speed = <3>;
> +
> + pinctrl-0 = <&pcie0_default_state>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +};
> +
> +&pcie1 {
> + wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
> + perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
> +
> + pinctrl-0 = <&pcie1_default_state>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +
> + pcie@0 {
> + /* Renesas μPD720201 PCIe USB3.0 HOST CONTROLLER */
> + usb-controller@0 {
> + compatible = "pci1912,0014";
> + reg = <0x10000 0x0 0x0 0x0 0x0>;
> +
> + avdd33-supply = <&upd720201_avdd33_reg>;
> + vdd10-supply = <&upd720201_vdd10_reg>;
> + vdd33-supply = <&upd720201_vdd33_reg>;
> +
> + pinctrl-0 = <&gamepad_pwr_en>;
> + pinctrl-names = "default";
> + };
> + };
> +};
> +
> +&pcie1_phy {
> + vdda-phy-supply = <&vreg_l3c_0p9>;
> + vdda-pll-supply = <&vreg_l3e_1p2>;
> + vdda-qref-supply = <&vreg_l1e_0p88>;
> +
> + status = "okay";
> +};
> +
> +&ufs_mem_hc {
> + reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
> +
> + vcc-supply = <&vreg_l17b_2p5>;
> + vcc-max-microamp = <1300000>;
> + vccq-supply = <&vreg_l1g_1p2>;
> + vccq-max-microamp = <1200000>;
> + vdd-hba-supply = <&vreg_l3g_1p2>;
> +
> + status = "okay";
> +};
> +
> +&ufs_mem_phy {
> + vdda-phy-supply = <&vreg_l1d_0p88>;
> + vdda-pll-supply = <&vreg_l3e_1p2>;
> +
> + status = "okay";
> +};
> +
> +&usb_1 {
> + status = "okay";
> +};
> +
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_hsphy {
> + vdd-supply = <&vreg_l1e_0p88>;
> + vdda12-supply = <&vreg_l3e_1p2>;
> +
> + phys = <&pm8550b_eusb2_repeater>;
> +
> + status = "okay";
> +};
> +
> +&usb_dp_qmpphy {
> + vdda-phy-supply = <&vreg_l3e_1p2>;
> + vdda-pll-supply = <&vreg_l3f_0p88>;
> +
> + status = "okay";
> +};
> +
> +&usb_dp_qmpphy_out {
> + remote-endpoint = <&redriver_ss_in>;
> +};
> +
> +&uart7 {
> + status = "okay";
> +};
> +
> +&uart14 {
> + status = "okay";
> +
> + bluetooth {
> + compatible = "qcom,wcn7850-bt";
> +
> + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
> + vddaon-supply = <&vreg_pmu_aon_0p59>;
> + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
> + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
> + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
> + vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
> +
> + max-speed = <3200000>;
> + };
> +};
> +
> +&iris {
Looks like random ordering...
> + status = "okay";
> +};
> +
Best regards,
Krzysztof
next prev parent reply other threads:[~2026-05-14 12:25 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-11 11:33 [PATCH v2 0/3] arm64: qcom: add Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
2026-05-11 11:33 ` [PATCH v2 1/3] dt-bindings: arm: qcom: document the Ayaneo Pocket DS Alexandre Hamamdjian via B4 Relay
2026-05-12 2:21 ` sashiko-bot
2026-05-14 12:20 ` Krzysztof Kozlowski
[not found] ` <CAL5cOWtRUs-XF5Y6+X-G3PVkGQp-ts+HTiAfzezVjQqYoyt1NQ@mail.gmail.com>
2026-05-14 12:31 ` Krzysztof Kozlowski
2026-05-11 11:33 ` [PATCH v2 2/3] arm64: dts: qcom: sm8550: add labels for thermal zones Alexandre Hamamdjian via B4 Relay
2026-05-11 12:55 ` Neil Armstrong
2026-05-12 2:24 ` sashiko-bot
2026-05-14 12:26 ` Krzysztof Kozlowski
2026-05-11 11:33 ` [PATCH v2 3/3] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
2026-05-12 3:50 ` sashiko-bot
2026-05-12 7:28 ` Neil Armstrong
2026-05-14 12:25 ` Krzysztof Kozlowski [this message]
[not found] ` <CAL5cOWtz5VZXGJBRVKNTwbXGciAom8PZ84cZFr2KveW7jO1O=A@mail.gmail.com>
[not found] ` <CAL5cOWu20Vng7hMZvyz0paFM6Ga=Fs2qQrF2yfMTpVvSt3b0VA@mail.gmail.com>
2026-05-14 13:46 ` Krzysztof Kozlowski
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260514-free-ruby-honeybee-d5f317@quoll \
--to=krzk@kernel.org \
--cc=andersson@kernel.org \
--cc=azkali.limited@gmail.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
--cc=teguh@sobir.in \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox