[PATCH V1 0/3] Add Hawi UFS PHY and Controller support

[PATCH V1 0/3] Add Hawi UFS PHY and Controller support

[palash.kambar]

From: Palash Kambar <palash.kambar@oss.qualcomm.com>

This series introduces devicetree binding documentation and PHY
initialization support required to enable UFS on this platform.

  1. Devicetree binding documentation for the QMP UFS PHY
     used on Qualcomm Hawi.
  2. Devicetree binding documentation for the UFS controller
     instance present on the Hawi platform.
  3. Initialization sequence tables and configuration required
     for the QMP UFS PHY on Hawi SoC.

Palash Kambar (3):
  dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: Add Hawi UFS PHY
    compatible
  dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: Document the Hawi UFS
    controller
  phy: qcom-qmp-ufs: Add UFS PHY support on Hawi

 .../phy/qcom,sc8280xp-qmp-ufs-phy.yaml        |   1 +
 .../bindings/ufs/qcom,sm8650-ufshc.yaml       |   2 +
 .../phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h    |  22 +++
 .../phy-qcom-qmp-qserdes-txrx-ufs-v8.h        |  37 +++++
 drivers/phy/qualcomm/phy-qcom-qmp-ufs.c       | 140 ++++++++++++++++++
 5 files changed, 202 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h

-- 
2.34.1

[PATCH V1 1/3] dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: Add Hawi UFS PHY compatible

[palash.kambar]

From: Palash Kambar <palash.kambar@oss.qualcomm.com>

Document QMP UFS PHY compatible for Hawi SoC.

Signed-off-by: Palash Kambar <palash.kambar@oss.qualcomm.com>
---
 .../devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml       | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml
index 9616c736b6d4..2326dcf38a46 100644
--- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml
@@ -37,6 +37,7 @@ properties:
               - qcom,kaanapali-qmp-ufs-phy
           - const: qcom,sm8750-qmp-ufs-phy
       - enum:
+          - qcom,hawi-qmp-ufs-phy
           - qcom,milos-qmp-ufs-phy
           - qcom,msm8996-qmp-ufs-phy
           - qcom,msm8998-qmp-ufs-phy
-- 
2.34.1

[PATCH V1 2/3] dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: Document the Hawi UFS controller

[palash.kambar]

From: Palash Kambar <palash.kambar@oss.qualcomm.com>

Document the UFS Controller on the Hawi Platform.

Signed-off-by: Palash Kambar <palash.kambar@oss.qualcomm.com>
---
 Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml b/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml
index f28641c6e68f..3de00affa4c6 100644
--- a/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml
+++ b/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml
@@ -16,6 +16,7 @@ select:
       contains:
         enum:
           - qcom,eliza-ufshc
+          - qcom,hawi-ufshc
           - qcom,kaanapali-ufshc
           - qcom,sm8650-ufshc
           - qcom,sm8750-ufshc
@@ -27,6 +28,7 @@ properties:
     items:
       - enum:
           - qcom,eliza-ufshc
+          - qcom,hawi-ufshc
           - qcom,kaanapali-ufshc
           - qcom,sm8650-ufshc
           - qcom,sm8750-ufshc
-- 
2.34.1

[PATCH V1 3/3] phy: qcom-qmp-ufs: Add UFS PHY support on Hawi

[palash.kambar]

From: Palash Kambar <palash.kambar@oss.qualcomm.com>

Add the init sequence tables and config for the UFS QMP phy found in
the Hawi SoC.

Signed-off-by: Palash Kambar <palash.kambar@oss.qualcomm.com>
---
 .../phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h    |  22 +++
 .../phy-qcom-qmp-qserdes-txrx-ufs-v8.h        |  37 +++++
 drivers/phy/qualcomm/phy-qcom-qmp-ufs.c       | 140 ++++++++++++++++++
 3 files changed, 199 insertions(+)
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h
 create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h
new file mode 100644
index 000000000000..bf914c752d22
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h
@@ -0,0 +1,22 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2026, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_PCS_UFS_V7_H_
+#define QCOM_PHY_QMP_PCS_UFS_V7_H_
+
+/* Only for QMP V7 PHY - UFS PCS registers */
+
+#define QPHY_V7_PCS_UFS_PCS_CTRL1			0x01C
+#define QPHY_V7_PCS_UFS_PLL_CNTL			0x028
+#define QPHY_V7_PCS_UFS_TX_LARGE_AMP_DRV_LVL		0x02C
+#define QPHY_V7_PCS_UFS_TX_HSGEAR_CAPABILITY		0x060
+#define QPHY_V7_PCS_UFS_RX_HSGEAR_CAPABILITY		0x094
+#define QPHY_V7_PCS_UFS_LINECFG_DISABLE			0x140
+#define QPHY_V7_PCS_UFS_RX_SIGDET_CTRL2			0x150
+#define QPHY_V7_PCS_UFS_READY_STATUS			0x16c
+#define QPHY_V7_PCS_UFS_TX_MID_TERM_CTRL1		0x1b8
+#define QPHY_V7_PCS_UFS_MULTI_LANE_CTRL1		0x1c0
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h
new file mode 100644
index 000000000000..5f923c3e64ec
--- /dev/null
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h
@@ -0,0 +1,37 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2026, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef QCOM_PHY_QMP_QSERDES_TXRX_UFS_V8_H_
+#define QCOM_PHY_QMP_QSERDES_TXRX_UFS_V8_H_
+
+#define QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_TX		(0x34)
+#define QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_RX		(0x38)
+#define QSERDES_UFS_V8_TX_LANE_MODE_1				(0x80)
+#define QSERDES_UFS_V8_RX_UCDR_FO_GAIN_RATE2			(0x1BC)
+#define QSERDES_UFS_V8_RX_UCDR_FO_GAIN_RATE4			(0x1C4)
+#define QSERDES_UFS_V8_RX_UCDR_SO_GAIN_RATE4			(0x1DC)
+#define QSERDES_UFS_V8_RX_EQ_OFFSET_ADAPTOR_CNTRL1		(0x2C8)
+#define QSERDES_UFS_V8_RX_UCDR_PI_CONTROLS			(0x1E4)
+#define QSERDES_UFS_V8_RX_OFFSET_ADAPTOR_CNTRL3			(0x2D0)
+#define QSERDES_UFS_V8_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4	(0x120)
+#define QSERDES_UFS_V8_RX_UCDR_FASTLOCK_FO_GAIN_RATE4		(0xD4)
+#define QSERDES_UFS_V8_RX_UCDR_FASTLOCK_SO_GAIN_RATE4		(0xEC)
+#define QSERDES_UFS_V8_RX_VGA_CAL_MAN_VAL			(0x288)
+#define QSERDES_UFS_V8_RX_EQU_ADAPTOR_CNTRL4			(0x2B0)
+#define QSERDES_UFS_V8_RX_MODE_RATE_0_1_B4			(0x324)
+#define QSERDES_UFS_V8_RX_MODE_RATE4_SA_B7			(0x3B4)
+#define QSERDES_UFS_V8_RX_MODE_RATE4_SA_B9			(0x3BC)
+#define QSERDES_UFS_V8_RX_MODE_RATE4_SB_B7			(0x3E0)
+#define QSERDES_UFS_V8_RX_MODE_RATE4_SB_B9			(0x3E8)
+#define QSERDES_UFS_V8_RX_MODE_RATE5_SA_B7			(0x40C)
+#define QSERDES_UFS_V8_RX_MODE_RATE5_SA_B9			(0x414)
+#define QSERDES_UFS_V8_RX_MODE_RATE5_SB_B7			(0x438)
+#define QSERDES_UFS_V8_RX_MODE_RATE5_SB_B9			(0x440)
+#define QSERDES_UFS_V8_RX_UCDR_SO_SATURATION			(0xF4)
+#define QSERDES_UFS_V8_RX_TERM_BW_CTRL0				(0x1AC)
+#define QSERDES_UFS_V8_RX_DLL0_FTUNE_CTRL			(0x498)
+#define QSERDES_UFS_V8_RX_SIGDET_CAL_TRIM			(0x4d0)
+
+#endif
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
index 771bc7c2ab50..a4801cf4b0fe 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
@@ -29,9 +29,11 @@
 #include "phy-qcom-qmp-pcs-ufs-v4.h"
 #include "phy-qcom-qmp-pcs-ufs-v5.h"
 #include "phy-qcom-qmp-pcs-ufs-v6.h"
+#include "phy-qcom-qmp-pcs-ufs-v7.h"
 
 #include "phy-qcom-qmp-qserdes-txrx-ufs-v6.h"
 #include "phy-qcom-qmp-qserdes-txrx-ufs-v7.h"
+#include "phy-qcom-qmp-qserdes-txrx-ufs-v8.h"
 
 /* QPHY_PCS_READY_STATUS bit */
 #define PCS_READY				BIT(0)
@@ -84,6 +86,13 @@ static const unsigned int ufsphy_v6_regs_layout[QPHY_LAYOUT_SIZE] = {
 	[QPHY_PCS_POWER_DOWN_CONTROL]	= QPHY_V6_PCS_UFS_POWER_DOWN_CONTROL,
 };
 
+static const unsigned int ufsphy_v7_regs_layout[QPHY_LAYOUT_SIZE] = {
+	[QPHY_START_CTRL]		= QPHY_V6_PCS_UFS_PHY_START,
+	[QPHY_PCS_READY_STATUS]		= QPHY_V7_PCS_UFS_READY_STATUS,
+	[QPHY_SW_RESET]			= QPHY_V6_PCS_UFS_SW_RESET,
+	[QPHY_PCS_POWER_DOWN_CONTROL]	= QPHY_V6_PCS_UFS_POWER_DOWN_CONTROL,
+};
+
 static const struct qmp_phy_init_tbl milos_ufsphy_serdes[] = {
 	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0xd9),
 	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16),
@@ -1306,6 +1315,12 @@ static const struct regulator_bulk_data sm8750_ufsphy_vreg_l[] = {
 	{ .supply = "vdda-pll", .init_load_uA = 18300 },
 };
 
+static const struct regulator_bulk_data hawi_ufsphy_vreg_l[] = {
+	{ .supply = "vdda-phy", .init_load_uA = 324000 },
+	{ .supply = "vdda-pll", .init_load_uA = 27000 },
+
+};
+
 static const struct qmp_ufs_offsets qmp_ufs_offsets = {
 	.serdes		= 0,
 	.pcs		= 0xc00,
@@ -1324,6 +1339,15 @@ static const struct qmp_ufs_offsets qmp_ufs_offsets_v6 = {
 	.rx2		= 0x1a00,
 };
 
+static const struct qmp_ufs_offsets qmp_ufs_offsets_v7 = {
+	.serdes		= 0,
+	.pcs		= 0x0400,
+	.tx		= 0x2000,
+	.rx		= 0x2000,
+	.tx2		= 0x3000,
+	.rx2		= 0x3000,
+};
+
 static const struct qmp_phy_cfg milos_ufsphy_cfg = {
 	.lanes			= 2,
 
@@ -1844,6 +1868,119 @@ static const struct qmp_phy_cfg sm8750_ufsphy_cfg = {
 
 };
 
+static const struct qmp_phy_init_tbl hawi_ufsphy_serdes[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0xd9),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x11),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_CFG, 0x60),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO_MODE1, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IETRIM, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IPTRIM, 0x20),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_CTRL, 0x40),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_ADAPTIVE_ANALOG_CONFIG, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_ADAPTIVE_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCCTRL_ADAPTIVE_MODE0, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_ADAPTIVE_MODE0, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE1_MODE0, 0x92),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE2_MODE0, 0x1e),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x4c),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_ADAPTIVE_MODE1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCCTRL_ADAPTIVE_MODE1, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_ADAPTIVE_MODE1, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x99),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE1_MODE1, 0xbe),
+	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE2_MODE1, 0x23),
+};
+
+static const struct qmp_phy_init_tbl hawi_ufsphy_tx[] = {
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_TX_LANE_MODE_1, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_TX, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_RX, 0x17),
+};
+
+static const struct qmp_phy_init_tbl hawi_ufsphy_rx[] = {
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_UCDR_FO_GAIN_RATE2, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_UCDR_FO_GAIN_RATE4, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_UCDR_SO_GAIN_RATE4, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_UCDR_PI_CONTROLS, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_OFFSET_ADAPTOR_CNTRL3, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_UCDR_FASTLOCK_FO_GAIN_RATE4, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_UCDR_FASTLOCK_SO_GAIN_RATE4, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_VGA_CAL_MAN_VAL, 0x8e),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_EQU_ADAPTOR_CNTRL4, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_MODE_RATE_0_1_B4, 0xb8),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_MODE_RATE4_SA_B7, 0x66),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_MODE_RATE4_SA_B9, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_MODE_RATE4_SB_B7, 0x66),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_MODE_RATE4_SB_B9, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_MODE_RATE5_SA_B7, 0x66),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_MODE_RATE5_SA_B9, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_MODE_RATE5_SB_B7, 0x66),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_MODE_RATE5_SB_B9, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_UCDR_SO_SATURATION, 0x1f),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_TERM_BW_CTRL0, 0xfa),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_DLL0_FTUNE_CTRL, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_RX_SIGDET_CAL_TRIM, 0x77),
+};
+
+static const struct qmp_phy_init_tbl hawi_ufsphy_pcs[] = {
+	QMP_PHY_INIT_CFG(QPHY_V7_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
+	QMP_PHY_INIT_CFG(QPHY_V7_PCS_UFS_PCS_CTRL1, 0x42),
+	QMP_PHY_INIT_CFG(QPHY_V7_PCS_UFS_TX_LARGE_AMP_DRV_LVL, 0x0f),
+	QMP_PHY_INIT_CFG(QPHY_V7_PCS_UFS_RX_SIGDET_CTRL2, 0x68),
+	QMP_PHY_INIT_CFG(QPHY_V7_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
+};
+
+static const struct qmp_phy_init_tbl hawi_ufsphy_g5_pcs[] = {
+	QMP_PHY_INIT_CFG(QPHY_V7_PCS_UFS_PLL_CNTL, 0x3b),
+	QMP_PHY_INIT_CFG(QPHY_V7_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x05),
+	QMP_PHY_INIT_CFG(QPHY_V7_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x05),
+};
+
+static const struct qmp_phy_cfg hawi_ufsphy_cfg = {
+	.lanes			= 2,
+
+	.offsets		= &qmp_ufs_offsets_v7,
+	.max_supported_gear	= UFS_HS_G5,
+
+	.tbls = {
+		.serdes		= hawi_ufsphy_serdes,
+		.serdes_num	= ARRAY_SIZE(hawi_ufsphy_serdes),
+		.tx		= hawi_ufsphy_tx,
+		.tx_num		= ARRAY_SIZE(hawi_ufsphy_tx),
+		.rx		= hawi_ufsphy_rx,
+		.rx_num		= ARRAY_SIZE(hawi_ufsphy_rx),
+		.pcs		= hawi_ufsphy_pcs,
+		.pcs_num	= ARRAY_SIZE(hawi_ufsphy_pcs),
+	},
+
+	.tbls_hs_overlay[0] = {
+		.pcs		= hawi_ufsphy_g5_pcs,
+		.pcs_num	= ARRAY_SIZE(hawi_ufsphy_g5_pcs),
+		.max_gear	= UFS_HS_G5,
+	},
+
+	.vreg_list		= hawi_ufsphy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(hawi_ufsphy_vreg_l),
+	.regs			= ufsphy_v7_regs_layout,
+};
+
 static void qmp_ufs_serdes_init(struct qmp_ufs *qmp, const struct qmp_phy_cfg_tbls *tbls)
 {
 	void __iomem *serdes = qmp->serdes;
@@ -2258,6 +2395,9 @@ static int qmp_ufs_probe(struct platform_device *pdev)
 
 static const struct of_device_id qmp_ufs_of_match_table[] = {
 	{
+		.compatible = "qcom,hawi-qmp-ufs-phy",
+		.data = &hawi_ufsphy_cfg,
+	}, {
 		.compatible = "qcom,milos-qmp-ufs-phy",
 		.data = &milos_ufsphy_cfg,
 	}, {
-- 
2.34.1

Re: [PATCH V1 1/3] dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: Add Hawi UFS PHY compatible

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] The `qcom,hawi-qmp-ufs-phy` compatible string is missing from the conditional blocks under `allOf`, leading to incomplete schema validation for clocks.
--

commit ef81b61a1b44f94e3b68451c007cd7fcd7dfb417
Author: Palash Kambar <palash.kambar@oss.qualcomm.com>

dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: Add Hawi UFS PHY compatible

This commit documents the QMP UFS PHY compatible string for the Hawi SoC.

> diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml
> index 9616c736b6d46..2326dcf38a467 100644
> --- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml
> +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml
> @@ -37,6 +37,7 @@ properties:
>                - qcom,kaanapali-qmp-ufs-phy
>            - const: qcom,sm8750-qmp-ufs-phy
>        - enum:
> +          - qcom,hawi-qmp-ufs-phy

Should qcom,hawi-qmp-ufs-phy also be added to the conditional blocks under
allOf?

When a new compatible string is added to the top-level compatible enum but
omitted from the existing conditional blocks, it falls back to the top-level
schema validation.

This loose validation allows 2 or 3 clocks with any names, which means
device trees for the Hawi PHY with incorrect or missing clock properties
will silently pass validation.

>            - qcom,milos-qmp-ufs-phy
>            - qcom,msm8996-qmp-ufs-phy
>            - qcom,msm8998-qmp-ufs-phy

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260518165346.1732548-1-palash.kambar@oss.qualcomm.com?part=1

Re: [PATCH V1 3/3] phy: qcom-qmp-ufs: Add UFS PHY support on Hawi

[Dmitry Baryshkov]

On Mon, May 18, 2026 at 10:23:46PM +0530, palash.kambar@oss.qualcomm.com wrote:
> From: Palash Kambar <palash.kambar@oss.qualcomm.com>
> 
> Add the init sequence tables and config for the UFS QMP phy found in
> the Hawi SoC.
> 
> Signed-off-by: Palash Kambar <palash.kambar@oss.qualcomm.com>
> ---
>  .../phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h    |  22 +++
>  .../phy-qcom-qmp-qserdes-txrx-ufs-v8.h        |  37 +++++
>  drivers/phy/qualcomm/phy-qcom-qmp-ufs.c       | 140 ++++++++++++++++++
>  3 files changed, 199 insertions(+)
>  create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h
>  create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h
> new file mode 100644
> index 000000000000..bf914c752d22
> --- /dev/null
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h
> @@ -0,0 +1,22 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (c) 2026, The Linux Foundation. All rights reserved.
> + */
> +
> +#ifndef QCOM_PHY_QMP_PCS_UFS_V7_H_
> +#define QCOM_PHY_QMP_PCS_UFS_V7_H_
> +
> +/* Only for QMP V7 PHY - UFS PCS registers */
> +
> +#define QPHY_V7_PCS_UFS_PCS_CTRL1			0x01C
> +#define QPHY_V7_PCS_UFS_PLL_CNTL			0x028
> +#define QPHY_V7_PCS_UFS_TX_LARGE_AMP_DRV_LVL		0x02C
> +#define QPHY_V7_PCS_UFS_TX_HSGEAR_CAPABILITY		0x060
> +#define QPHY_V7_PCS_UFS_RX_HSGEAR_CAPABILITY		0x094
> +#define QPHY_V7_PCS_UFS_LINECFG_DISABLE			0x140
> +#define QPHY_V7_PCS_UFS_RX_SIGDET_CTRL2			0x150
> +#define QPHY_V7_PCS_UFS_READY_STATUS			0x16c
> +#define QPHY_V7_PCS_UFS_TX_MID_TERM_CTRL1		0x1b8
> +#define QPHY_V7_PCS_UFS_MULTI_LANE_CTRL1		0x1c0
> +
> +#endif
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h
> new file mode 100644
> index 000000000000..5f923c3e64ec
> --- /dev/null
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h
> @@ -0,0 +1,37 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * Copyright (c) 2026, The Linux Foundation. All rights reserved.
> + */
> +
> +#ifndef QCOM_PHY_QMP_QSERDES_TXRX_UFS_V8_H_
> +#define QCOM_PHY_QMP_QSERDES_TXRX_UFS_V8_H_
> +
> +#define QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_TX		(0x34)
> +#define QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_RX		(0x38)
> +#define QSERDES_UFS_V8_TX_LANE_MODE_1				(0x80)
> +#define QSERDES_UFS_V8_RX_UCDR_FO_GAIN_RATE2			(0x1BC)
> +#define QSERDES_UFS_V8_RX_UCDR_FO_GAIN_RATE4			(0x1C4)
> +#define QSERDES_UFS_V8_RX_UCDR_SO_GAIN_RATE4			(0x1DC)
> +#define QSERDES_UFS_V8_RX_EQ_OFFSET_ADAPTOR_CNTRL1		(0x2C8)
> +#define QSERDES_UFS_V8_RX_UCDR_PI_CONTROLS			(0x1E4)
> +#define QSERDES_UFS_V8_RX_OFFSET_ADAPTOR_CNTRL3			(0x2D0)
> +#define QSERDES_UFS_V8_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4	(0x120)
> +#define QSERDES_UFS_V8_RX_UCDR_FASTLOCK_FO_GAIN_RATE4		(0xD4)
> +#define QSERDES_UFS_V8_RX_UCDR_FASTLOCK_SO_GAIN_RATE4		(0xEC)
> +#define QSERDES_UFS_V8_RX_VGA_CAL_MAN_VAL			(0x288)
> +#define QSERDES_UFS_V8_RX_EQU_ADAPTOR_CNTRL4			(0x2B0)
> +#define QSERDES_UFS_V8_RX_MODE_RATE_0_1_B4			(0x324)
> +#define QSERDES_UFS_V8_RX_MODE_RATE4_SA_B7			(0x3B4)
> +#define QSERDES_UFS_V8_RX_MODE_RATE4_SA_B9			(0x3BC)
> +#define QSERDES_UFS_V8_RX_MODE_RATE4_SB_B7			(0x3E0)
> +#define QSERDES_UFS_V8_RX_MODE_RATE4_SB_B9			(0x3E8)
> +#define QSERDES_UFS_V8_RX_MODE_RATE5_SA_B7			(0x40C)
> +#define QSERDES_UFS_V8_RX_MODE_RATE5_SA_B9			(0x414)
> +#define QSERDES_UFS_V8_RX_MODE_RATE5_SB_B7			(0x438)
> +#define QSERDES_UFS_V8_RX_MODE_RATE5_SB_B9			(0x440)
> +#define QSERDES_UFS_V8_RX_UCDR_SO_SATURATION			(0xF4)
> +#define QSERDES_UFS_V8_RX_TERM_BW_CTRL0				(0x1AC)
> +#define QSERDES_UFS_V8_RX_DLL0_FTUNE_CTRL			(0x498)
> +#define QSERDES_UFS_V8_RX_SIGDET_CAL_TRIM			(0x4d0)
> +
> +#endif
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> index 771bc7c2ab50..a4801cf4b0fe 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> @@ -29,9 +29,11 @@
>  #include "phy-qcom-qmp-pcs-ufs-v4.h"
>  #include "phy-qcom-qmp-pcs-ufs-v5.h"
>  #include "phy-qcom-qmp-pcs-ufs-v6.h"
> +#include "phy-qcom-qmp-pcs-ufs-v7.h"
>  
>  #include "phy-qcom-qmp-qserdes-txrx-ufs-v6.h"
>  #include "phy-qcom-qmp-qserdes-txrx-ufs-v7.h"
> +#include "phy-qcom-qmp-qserdes-txrx-ufs-v8.h"
>  
>  /* QPHY_PCS_READY_STATUS bit */
>  #define PCS_READY				BIT(0)
> @@ -84,6 +86,13 @@ static const unsigned int ufsphy_v6_regs_layout[QPHY_LAYOUT_SIZE] = {
>  	[QPHY_PCS_POWER_DOWN_CONTROL]	= QPHY_V6_PCS_UFS_POWER_DOWN_CONTROL,
>  };
>  
> +static const unsigned int ufsphy_v7_regs_layout[QPHY_LAYOUT_SIZE] = {
> +	[QPHY_START_CTRL]		= QPHY_V6_PCS_UFS_PHY_START,
> +	[QPHY_PCS_READY_STATUS]		= QPHY_V7_PCS_UFS_READY_STATUS,
> +	[QPHY_SW_RESET]			= QPHY_V6_PCS_UFS_SW_RESET,
> +	[QPHY_PCS_POWER_DOWN_CONTROL]	= QPHY_V6_PCS_UFS_POWER_DOWN_CONTROL,

Don't mix V6 and V7 registers. And why is it v7? The rest of the
registers point out a v8 PHY.

> +};
> +
>  static const struct qmp_phy_init_tbl milos_ufsphy_serdes[] = {
>  	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0xd9),
>  	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16),
> @@ -1844,6 +1868,119 @@ static const struct qmp_phy_cfg sm8750_ufsphy_cfg = {
>  
>  };
>  
> +static const struct qmp_phy_init_tbl hawi_ufsphy_serdes[] = {
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0xd9),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x11),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x01),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_CFG, 0x60),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x1f),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO_MODE1, 0x1f),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IETRIM, 0x07),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IPTRIM, 0x20),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_CTRL, 0x40),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_ADAPTIVE_ANALOG_CONFIG, 0x06),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x06),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_ADAPTIVE_MODE0, 0x06),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCCTRL_ADAPTIVE_MODE0, 0x18),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_ADAPTIVE_MODE0, 0x14),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x7f),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x06),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE1_MODE0, 0x92),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE2_MODE0, 0x1e),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x4c),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x06),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x18),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x14),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_ADAPTIVE_MODE1, 0x06),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCCTRL_ADAPTIVE_MODE1, 0x18),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_ADAPTIVE_MODE1, 0x14),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x99),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x07),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE1_MODE1, 0xbe),
> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE2_MODE1, 0x23),

Yep... If it is V8, use V8 registers. Even if they are they same.

> +};
> +
> +static const struct qmp_phy_init_tbl hawi_ufsphy_tx[] = {
> +	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_TX_LANE_MODE_1, 0x0c),
> +	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_TX, 0x07),
> +	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_RX, 0x17),

And it's V8.

> +};
> +

-- 
With best wishes
Dmitry

Re: [PATCH V1 2/3] dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: Document the Hawi UFS controller

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:
- [Medium] The commit title specifies the wrong subsystem and filename relative to the actual diff.
- [Medium] The new compatible string 'qcom,hawi-ufshc' is omitted from the `if-then` conditional block that enforces the MCQ register range constraints.
--

commit 1742ce0580b168eb19f1dc60a097e13ccbf8098d
Author: Palash Kambar <palash.kambar@oss.qualcomm.com>

dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: Document the Hawi UFS controller
    
Document the UFS Controller on the Hawi Platform.

> dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: Document the Hawi UFS controller

This isn't a bug, but the commit title specifies the wrong subsystem and
filename. It claims to modify the PHY binding qcom,sc8280xp-qmp-ufs-phy,
but the patch actually modifies the UFS host controller binding
Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml.

> diff --git a/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml b/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml
> index f28641c6e68fe..3de00affa4c64 100644
> --- a/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml
> +++ b/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml
[ ... ]
> @@ -27,6 +28,7 @@ properties:
>      items:
>        - enum:
>            - qcom,eliza-ufshc
> +          - qcom,hawi-ufshc
>            - qcom,kaanapali-ufshc
>            - qcom,sm8650-ufshc
>            - qcom,sm8750-ufshc

Does this code omit qcom,hawi-ufshc from the conditional block further down in
the file that enforces the MCQ register range constraints?

Looking at the allOf block in this file:

allOf:
  - $ref: qcom,ufs-common.yaml
  - if:
      properties:
        compatible:
          contains:
            enum:
              - qcom,eliza-ufshc
    then:
      properties:
        reg:
          minItems: 2
        reg-names:
          minItems: 2

If the Hawi platform shares the same hardware constraints and requires the MCQ
registers, could this regression allow incomplete device trees missing the MCQ
registers to silently pass schema validation by being omitted from this block?

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260518165346.1732548-1-palash.kambar@oss.qualcomm.com?part=2

Re: [PATCH V1 3/3] phy: qcom-qmp-ufs: Add UFS PHY support on Hawi

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [High] Missing UFS HS-G4 gear configuration overlay for the Hawi PHY will leave critical hardware capabilities uninitialized during G4 negotiation.
--

commit a0d83dfe8a3203b506d45d5c8262f7f0b14d810a
Author: Palash Kambar <palash.kambar@oss.qualcomm.com>

phy: qcom-qmp-ufs: Add UFS PHY support on Hawi

Adds the initialization sequence tables and configuration for the UFS
QMP PHY found in the Hawi SoC.

> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
[ ... ]
> @@ -1844,6 +1868,119 @@ static const struct qmp_phy_cfg sm8750_ufsphy_cfg = {
[ ... ]
> +static const struct qmp_phy_init_tbl hawi_ufsphy_g5_pcs[] = {
> +	QMP_PHY_INIT_CFG(QPHY_V7_PCS_UFS_PLL_CNTL, 0x3b),
> +	QMP_PHY_INIT_CFG(QPHY_V7_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x05),
> +	QMP_PHY_INIT_CFG(QPHY_V7_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x05),
> +};
> +
> +static const struct qmp_phy_cfg hawi_ufsphy_cfg = {
> +	.lanes			= 2,
> +
> +	.offsets		= &qmp_ufs_offsets_v7,
> +	.max_supported_gear	= UFS_HS_G5,
> +
> +	.tbls = {
> +		.serdes		= hawi_ufsphy_serdes,
> +		.serdes_num	= ARRAY_SIZE(hawi_ufsphy_serdes),
> +		.tx		= hawi_ufsphy_tx,
> +		.tx_num		= ARRAY_SIZE(hawi_ufsphy_tx),
> +		.rx		= hawi_ufsphy_rx,
> +		.rx_num		= ARRAY_SIZE(hawi_ufsphy_rx),
> +		.pcs		= hawi_ufsphy_pcs,
> +		.pcs_num	= ARRAY_SIZE(hawi_ufsphy_pcs),
> +	},
> +
> +	.tbls_hs_overlay[0] = {
> +		.pcs		= hawi_ufsphy_g5_pcs,
> +		.pcs_num	= ARRAY_SIZE(hawi_ufsphy_g5_pcs),
> +		.max_gear	= UFS_HS_G5,
> +	},
> +

Is there a missing UFS HS-G4 gear configuration overlay for the Hawi PHY here?

When the UFS controller negotiates HS-G4 (e.g., connected to a G4-only
device or during fallback) and requests the PHY to operate at G4,
qmp_ufs_get_gear_overlay() will fail to find a matching configuration.

In qmp_ufs_get_gear_overlay(), it initializes floor_max_gear to 5.
It then checks the only available table where max_gear is 5.
Since submode (4) == max_gear (5) is false, and max_gear (5) <
floor_max_gear (5) is also false, it returns -EINVAL.

Because qmp_ufs_get_gear_overlay() returns -EINVAL,
qmp_ufs_init_registers() will skip applying any overlay. This means
capabilities like QPHY_V7_PCS_UFS_TX_HSGEAR_CAPABILITY are never
programmed during G4 operation.

Other G5-capable PHYs (like sm8750) seem to provide both G4 and G5 overlays:

static const struct qmp_phy_cfg sm8750_ufsphy_cfg = {
[ ... ]
	.tbls_hs_overlay[0] = {
		.pcs		= sm8750_ufsphy_g4_pcs,
		.pcs_num	= ARRAY_SIZE(sm8750_ufsphy_g4_pcs),
		.max_gear	= UFS_HS_G4,
	},
	.tbls_hs_overlay[1] = {
		.pcs		= sm8650_ufsphy_g5_pcs,
		.pcs_num	= ARRAY_SIZE(sm8650_ufsphy_g5_pcs),
		.max_gear	= UFS_HS_G5,
	},
[ ... ]
};

Will leaving these uninitialized cause link instability or initialization
failure on devices falling back to HS-G4?

> +	.vreg_list		= hawi_ufsphy_vreg_l,
> +	.num_vregs		= ARRAY_SIZE(hawi_ufsphy_vreg_l),
> +	.regs			= ufsphy_v7_regs_layout,
> +};

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260518165346.1732548-1-palash.kambar@oss.qualcomm.com?part=3

Re: [PATCH V1 3/3] phy: qcom-qmp-ufs: Add UFS PHY support on Hawi

[Palash Kambar]

On 5/18/2026 10:39 PM, Dmitry Baryshkov wrote:
> On Mon, May 18, 2026 at 10:23:46PM +0530, palash.kambar@oss.qualcomm.com wrote:
>> From: Palash Kambar <palash.kambar@oss.qualcomm.com>
>>
>> Add the init sequence tables and config for the UFS QMP phy found in
>> the Hawi SoC.
>>
>> Signed-off-by: Palash Kambar <palash.kambar@oss.qualcomm.com>
>> ---
>>  .../phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h    |  22 +++
>>  .../phy-qcom-qmp-qserdes-txrx-ufs-v8.h        |  37 +++++
>>  drivers/phy/qualcomm/phy-qcom-qmp-ufs.c       | 140 ++++++++++++++++++
>>  3 files changed, 199 insertions(+)
>>  create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h
>>  create mode 100644 drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h
>>
>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h
>> new file mode 100644
>> index 000000000000..bf914c752d22
>> --- /dev/null
>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-pcs-ufs-v7.h
>> @@ -0,0 +1,22 @@
>> +/* SPDX-License-Identifier: GPL-2.0 */
>> +/*
>> + * Copyright (c) 2026, The Linux Foundation. All rights reserved.
>> + */
>> +
>> +#ifndef QCOM_PHY_QMP_PCS_UFS_V7_H_
>> +#define QCOM_PHY_QMP_PCS_UFS_V7_H_
>> +
>> +/* Only for QMP V7 PHY - UFS PCS registers */
>> +
>> +#define QPHY_V7_PCS_UFS_PCS_CTRL1			0x01C
>> +#define QPHY_V7_PCS_UFS_PLL_CNTL			0x028
>> +#define QPHY_V7_PCS_UFS_TX_LARGE_AMP_DRV_LVL		0x02C
>> +#define QPHY_V7_PCS_UFS_TX_HSGEAR_CAPABILITY		0x060
>> +#define QPHY_V7_PCS_UFS_RX_HSGEAR_CAPABILITY		0x094
>> +#define QPHY_V7_PCS_UFS_LINECFG_DISABLE			0x140
>> +#define QPHY_V7_PCS_UFS_RX_SIGDET_CTRL2			0x150
>> +#define QPHY_V7_PCS_UFS_READY_STATUS			0x16c
>> +#define QPHY_V7_PCS_UFS_TX_MID_TERM_CTRL1		0x1b8
>> +#define QPHY_V7_PCS_UFS_MULTI_LANE_CTRL1		0x1c0
>> +
>> +#endif
>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h
>> new file mode 100644
>> index 000000000000..5f923c3e64ec
>> --- /dev/null
>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-qserdes-txrx-ufs-v8.h
>> @@ -0,0 +1,37 @@
>> +/* SPDX-License-Identifier: GPL-2.0 */
>> +/*
>> + * Copyright (c) 2026, The Linux Foundation. All rights reserved.
>> + */
>> +
>> +#ifndef QCOM_PHY_QMP_QSERDES_TXRX_UFS_V8_H_
>> +#define QCOM_PHY_QMP_QSERDES_TXRX_UFS_V8_H_
>> +
>> +#define QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_TX		(0x34)
>> +#define QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_RX		(0x38)
>> +#define QSERDES_UFS_V8_TX_LANE_MODE_1				(0x80)
>> +#define QSERDES_UFS_V8_RX_UCDR_FO_GAIN_RATE2			(0x1BC)
>> +#define QSERDES_UFS_V8_RX_UCDR_FO_GAIN_RATE4			(0x1C4)
>> +#define QSERDES_UFS_V8_RX_UCDR_SO_GAIN_RATE4			(0x1DC)
>> +#define QSERDES_UFS_V8_RX_EQ_OFFSET_ADAPTOR_CNTRL1		(0x2C8)
>> +#define QSERDES_UFS_V8_RX_UCDR_PI_CONTROLS			(0x1E4)
>> +#define QSERDES_UFS_V8_RX_OFFSET_ADAPTOR_CNTRL3			(0x2D0)
>> +#define QSERDES_UFS_V8_RX_UCDR_FASTLOCK_COUNT_HIGH_RATE4	(0x120)
>> +#define QSERDES_UFS_V8_RX_UCDR_FASTLOCK_FO_GAIN_RATE4		(0xD4)
>> +#define QSERDES_UFS_V8_RX_UCDR_FASTLOCK_SO_GAIN_RATE4		(0xEC)
>> +#define QSERDES_UFS_V8_RX_VGA_CAL_MAN_VAL			(0x288)
>> +#define QSERDES_UFS_V8_RX_EQU_ADAPTOR_CNTRL4			(0x2B0)
>> +#define QSERDES_UFS_V8_RX_MODE_RATE_0_1_B4			(0x324)
>> +#define QSERDES_UFS_V8_RX_MODE_RATE4_SA_B7			(0x3B4)
>> +#define QSERDES_UFS_V8_RX_MODE_RATE4_SA_B9			(0x3BC)
>> +#define QSERDES_UFS_V8_RX_MODE_RATE4_SB_B7			(0x3E0)
>> +#define QSERDES_UFS_V8_RX_MODE_RATE4_SB_B9			(0x3E8)
>> +#define QSERDES_UFS_V8_RX_MODE_RATE5_SA_B7			(0x40C)
>> +#define QSERDES_UFS_V8_RX_MODE_RATE5_SA_B9			(0x414)
>> +#define QSERDES_UFS_V8_RX_MODE_RATE5_SB_B7			(0x438)
>> +#define QSERDES_UFS_V8_RX_MODE_RATE5_SB_B9			(0x440)
>> +#define QSERDES_UFS_V8_RX_UCDR_SO_SATURATION			(0xF4)
>> +#define QSERDES_UFS_V8_RX_TERM_BW_CTRL0				(0x1AC)
>> +#define QSERDES_UFS_V8_RX_DLL0_FTUNE_CTRL			(0x498)
>> +#define QSERDES_UFS_V8_RX_SIGDET_CAL_TRIM			(0x4d0)
>> +
>> +#endif
>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>> index 771bc7c2ab50..a4801cf4b0fe 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>> @@ -29,9 +29,11 @@
>>  #include "phy-qcom-qmp-pcs-ufs-v4.h"
>>  #include "phy-qcom-qmp-pcs-ufs-v5.h"
>>  #include "phy-qcom-qmp-pcs-ufs-v6.h"
>> +#include "phy-qcom-qmp-pcs-ufs-v7.h"
>>  
>>  #include "phy-qcom-qmp-qserdes-txrx-ufs-v6.h"
>>  #include "phy-qcom-qmp-qserdes-txrx-ufs-v7.h"
>> +#include "phy-qcom-qmp-qserdes-txrx-ufs-v8.h"
>>  
>>  /* QPHY_PCS_READY_STATUS bit */
>>  #define PCS_READY				BIT(0)
>> @@ -84,6 +86,13 @@ static const unsigned int ufsphy_v6_regs_layout[QPHY_LAYOUT_SIZE] = {
>>  	[QPHY_PCS_POWER_DOWN_CONTROL]	= QPHY_V6_PCS_UFS_POWER_DOWN_CONTROL,
>>  };
>>  
>> +static const unsigned int ufsphy_v7_regs_layout[QPHY_LAYOUT_SIZE] = {
>> +	[QPHY_START_CTRL]		= QPHY_V6_PCS_UFS_PHY_START,
>> +	[QPHY_PCS_READY_STATUS]		= QPHY_V7_PCS_UFS_READY_STATUS,
>> +	[QPHY_SW_RESET]			= QPHY_V6_PCS_UFS_SW_RESET,
>> +	[QPHY_PCS_POWER_DOWN_CONTROL]	= QPHY_V6_PCS_UFS_POWER_DOWN_CONTROL,
> 
> Don't mix V6 and V7 registers. And why is it v7? The rest of the
> registers point out a v8 PHY.
> 
>> +};
>> +
>>  static const struct qmp_phy_init_tbl milos_ufsphy_serdes[] = {
>>  	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0xd9),
>>  	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16),
>> @@ -1844,6 +1868,119 @@ static const struct qmp_phy_cfg sm8750_ufsphy_cfg = {
>>  
>>  };
>>  
>> +static const struct qmp_phy_init_tbl hawi_ufsphy_serdes[] = {
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_SYSCLK_EN_SEL, 0xd9),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_CONFIG_1, 0x16),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_SEL_1, 0x11),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_HSCLK_HS_SWITCH_SEL_1, 0x00),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_EN, 0x01),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP_CFG, 0x60),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO, 0x1f),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_IVCO_MODE1, 0x1f),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IETRIM, 0x07),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CMN_IPTRIM, 0x20),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_MAP, 0x04),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_VCO_TUNE_CTRL, 0x40),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_ADAPTIVE_ANALOG_CONFIG, 0x06),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE0, 0x41),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE0, 0x06),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE0, 0x18),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE0, 0x14),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_ADAPTIVE_MODE0, 0x06),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCCTRL_ADAPTIVE_MODE0, 0x18),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_ADAPTIVE_MODE0, 0x14),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE0, 0x7f),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE0, 0x06),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE1_MODE0, 0x92),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE2_MODE0, 0x1e),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_DEC_START_MODE1, 0x4c),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_MODE1, 0x06),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCTRL_MODE1, 0x18),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_MODE1, 0x14),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_CP_CTRL_ADAPTIVE_MODE1, 0x06),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_RCCTRL_ADAPTIVE_MODE1, 0x18),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_PLL_CCTRL_ADAPTIVE_MODE1, 0x14),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP1_MODE1, 0x99),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_LOCK_CMP2_MODE1, 0x07),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE1_MODE1, 0xbe),
>> +	QMP_PHY_INIT_CFG(QSERDES_V6_COM_BIN_VCOCAL_CMP_CODE2_MODE1, 0x23),
> 
> Yep... If it is V8, use V8 registers. Even if they are they same.
> 
>> +};
>> +
>> +static const struct qmp_phy_init_tbl hawi_ufsphy_tx[] = {
>> +	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_TX_LANE_MODE_1, 0x0c),
>> +	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_TX, 0x07),
>> +	QMP_PHY_INIT_CFG(QSERDES_UFS_V8_TX_RES_CODE_LANE_OFFSET_RX, 0x17),
> 
> And it's V8.
> 

Sure Dmitry, will update. Thanks.


>> +};
>> +
> 

Re: [PATCH V1 2/3] dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: Document the Hawi UFS controller

[Manivannan Sadhasivam]

On Mon, May 18, 2026 at 10:23:45PM +0530, palash.kambar@oss.qualcomm.com wrote:
> From: Palash Kambar <palash.kambar@oss.qualcomm.com>
> 

Subject is wrong. It should be:

scsi: ufs: qcom: dt-bindings:

- Mani

> Document the UFS Controller on the Hawi Platform.
> 
> Signed-off-by: Palash Kambar <palash.kambar@oss.qualcomm.com>
> ---
>  Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml | 2 ++
>  1 file changed, 2 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml b/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml
> index f28641c6e68f..3de00affa4c6 100644
> --- a/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml
> +++ b/Documentation/devicetree/bindings/ufs/qcom,sm8650-ufshc.yaml
> @@ -16,6 +16,7 @@ select:
>        contains:
>          enum:
>            - qcom,eliza-ufshc
> +          - qcom,hawi-ufshc
>            - qcom,kaanapali-ufshc
>            - qcom,sm8650-ufshc
>            - qcom,sm8750-ufshc
> @@ -27,6 +28,7 @@ properties:
>      items:
>        - enum:
>            - qcom,eliza-ufshc
> +          - qcom,hawi-ufshc
>            - qcom,kaanapali-ufshc
>            - qcom,sm8650-ufshc
>            - qcom,sm8750-ufshc
> -- 
> 2.34.1
> 

-- 
மணிவண்ணன் சதாசிவம்

Re: [PATCH V1 1/3] dt-bindings: phy: qcom,sc8280xp-qmp-ufs-phy: Add Hawi UFS PHY compatible

[Manivannan Sadhasivam]

On Mon, May 18, 2026 at 10:23:44PM +0530, palash.kambar@oss.qualcomm.com wrote:
> From: Palash Kambar <palash.kambar@oss.qualcomm.com>
> 
> Document QMP UFS PHY compatible for Hawi SoC.
> 
> Signed-off-by: Palash Kambar <palash.kambar@oss.qualcomm.com>
> ---
>  .../devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml       | 1 +
>  1 file changed, 1 insertion(+)
> 
> diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml
> index 9616c736b6d4..2326dcf38a46 100644
> --- a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml
> +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml
> @@ -37,6 +37,7 @@ properties:
>                - qcom,kaanapali-qmp-ufs-phy
>            - const: qcom,sm8750-qmp-ufs-phy
>        - enum:
> +          - qcom,hawi-qmp-ufs-phy

Don't you need to add the Hawi compatible to the below check for clocks?

- Mani

-- 
மணிவண்ணன் சதாசிவம்