[PATCH v11] riscv: dts: spacemit: k1-musepi-pro: add SD card support with UHS modes

[Andre Heider <a.heider@gmail.com>]

From: Trevor Gamblin <tgamblin@baylibre.com>

Update the Muse Pi Pro devicetree with SD card support to match what
was done for the OrangePi RV2 in [1]. More precisely:

- Enable sdhci0 controller with 4-bit bus width
- Configure card detect GPIO with internal pull-up support
- Connect vmmc-supply to buck4 for 3.3V card power
- Connect vqmmc-supply to aldo1 for 1.8V/3.3V I/O switching
- Add dual pinctrl states for voltage-dependent pin configuration
- Support UHS-I SDR25, SDR50, and SDR104 modes
- Add stable MMC device aliases (mmc0 = eMMC, mmc1 = SD card)

[1] https://lore.kernel.org/linux-riscv/20260316-orangepi-sd-card-uhs-v3-0-aefd3b7832df@gmail.com/T/#

Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Trevor Gamblin <tgamblin@baylibre.com>
Signed-off-by: Iker Pedrosa <ikerpedrosam@gmail.com>
Signed-off-by: Andre Heider <a.heider@gmail.com>
---

Hi,

this is just a rebase of Iker's v10 4/4 patch[0] on top of my merged
musepi-pro series[1].

[0] https://lore.kernel.org/all/20260515-orangepi-sd-card-uhs-v10-4-094af27e310d@gmail.com/
[1] https://lore.kernel.org/all/20260513071958.29574-1-a.heider@gmail.com/


 .../riscv/boot/dts/spacemit/k1-musepi-pro.dts | 22 ++++++++++++++++++-
 1 file changed, 21 insertions(+), 1 deletion(-)

diff --git a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
index 4aef287353cab..0d809e4ad3b1f 100644
--- a/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-musepi-pro.dts
@@ -19,6 +19,8 @@ aliases {
 		serial0 = &uart0;
 		i2c2 = &i2c2;
 		i2c8 = &i2c8;
+		mmc0 = &emmc;
+		mmc1 = &sdhci0;
 	};
 
 	chosen {
@@ -218,7 +220,7 @@ buck6 {
 				regulator-always-on;
 			};
 
-			aldo1 {
+			aldo1: aldo1 {
 				regulator-min-microvolt = <500000>;
 				regulator-max-microvolt = <3400000>;
 				regulator-boot-on;
@@ -384,3 +386,21 @@ hub_3_0: hub@2 {
 		reset-gpios = <&gpio K1_GPIO(123) GPIO_ACTIVE_LOW>; /* HUB_RST */
 	};
 };
+
+&sdhci0 {
+	pinctrl-names = "default", "uhs";
+	pinctrl-0 = <&mmc1_cfg>;
+	pinctrl-1 = <&mmc1_uhs_cfg>;
+	bus-width = <4>;
+	cd-gpios = <&gpio K1_GPIO(80) (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>;
+	no-mmc;
+	no-sdio;
+	disable-wp;
+	cap-sd-highspeed;
+	vmmc-supply = <&buck4_3v3>;
+	vqmmc-supply = <&aldo1>;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	status = "okay";
+};
-- 
2.53.0