Devicetree
 help / color / mirror / Atom feed
From: Lee Jones <lee@kernel.org>
To: Svyatoslav Ryhel <clamor95@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>,
	Rob Herring <robh@kernel.org>,
	Krzysztof Kozlowski <krzk+dt@kernel.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Pavel Machek <pavel@kernel.org>,
	David Lechner <dlechner@baylibre.com>,
	Tony Lindgren <tony@atomide.com>,
	linux-input@vger.kernel.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-leds@vger.kernel.org
Subject: Re: [PATCH v5 5/6] mfd: motorola-cpcap: diverge configuration per-board
Date: Wed, 20 May 2026 16:07:58 +0100	[thread overview]
Message-ID: <20260520150758.GG2767592@google.com> (raw)
In-Reply-To: <20260510110804.33045-6-clamor95@gmail.com>

On Sun, 10 May 2026, Svyatoslav Ryhel wrote:

> MFD have rigid subdevice structure which does not allow flexible dynamic
> subdevice linking. Address this by diverging CPCAP subdevice composition
> to take into account board specific configuration.
> 
> Create a common default subdevice composition, rename existing subdevice
> composition into cpcap_mapphone_mfd_devices since it targets mainly
> Mapphone board.
> 
> Removed st,6556002 as it is no longer applicable to all cases and
> duplicates motorola,cpcap, which is used as the default composition.
> 
> Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
> ---
>  drivers/mfd/motorola-cpcap.c       | 142 ++++++++++++++++-------------
>  include/linux/mfd/motorola-cpcap.h |   6 ++
>  2 files changed, 87 insertions(+), 61 deletions(-)

Looking much better, thanks.

Nit: A patch-level changelog really is much more helpful to reviewers.

> diff --git a/drivers/mfd/motorola-cpcap.c b/drivers/mfd/motorola-cpcap.c
> index d8243b956f87..f5a7fdd89dd5 100644
> --- a/drivers/mfd/motorola-cpcap.c
> +++ b/drivers/mfd/motorola-cpcap.c
> @@ -12,6 +12,7 @@
>  #include <linux/kernel.h>
>  #include <linux/module.h>
>  #include <linux/mod_devicetable.h>
> +#include <linux/property.h>
>  #include <linux/regmap.h>
>  #include <linux/sysfs.h>
>  
> @@ -30,6 +31,7 @@ struct cpcap_ddata {
>  	struct regmap_irq_chip_data *irqdata[CPCAP_NR_IRQ_CHIPS];
>  	const struct regmap_config *regmap_conf;
>  	struct regmap *regmap;
> +	enum cpcap_variant variant;
>  };
>  
>  static int cpcap_sense_irq(struct regmap *regmap, int irq)
> @@ -195,20 +197,6 @@ static int cpcap_init_irq(struct cpcap_ddata *cpcap)
>  	return 0;
>  }
>  
> -static const struct of_device_id cpcap_of_match[] = {
> -	{ .compatible = "motorola,cpcap", },
> -	{ .compatible = "st,6556002", },
> -	{},
> -};
> -MODULE_DEVICE_TABLE(of, cpcap_of_match);
> -
> -static const struct spi_device_id cpcap_spi_ids[] = {
> -	{ .name = "cpcap", },
> -	{ .name = "6556002", },
> -	{},
> -};
> -MODULE_DEVICE_TABLE(spi, cpcap_spi_ids);
> -
>  static const struct regmap_config cpcap_regmap_config = {
>  	.reg_bits = 16,
>  	.reg_stride = 4,
> @@ -241,62 +229,76 @@ static int cpcap_resume(struct device *dev)
>  
>  static DEFINE_SIMPLE_DEV_PM_OPS(cpcap_pm, cpcap_suspend, cpcap_resume);
>  
> -static const struct mfd_cell cpcap_mfd_devices[] = {
> -	{
> -		.name          = "cpcap_adc",
> -		.of_compatible = "motorola,mapphone-cpcap-adc",
> -	}, {
> -		.name          = "cpcap_battery",
> -		.of_compatible = "motorola,cpcap-battery",
> -	}, {
> -		.name          = "cpcap-charger",
> -		.of_compatible = "motorola,mapphone-cpcap-charger",
> -	}, {
> -		.name          = "cpcap-regulator",
> -		.of_compatible = "motorola,mapphone-cpcap-regulator",
> -	}, {
> -		.name          = "cpcap-rtc",
> -		.of_compatible = "motorola,cpcap-rtc",
> -	}, {
> -		.name          = "cpcap-pwrbutton",
> -		.of_compatible = "motorola,cpcap-pwrbutton",
> -	}, {
> -		.name          = "cpcap-usb-phy",
> -		.of_compatible = "motorola,mapphone-cpcap-usb-phy",
> -	}, {
> -		.name          = "cpcap-led",
> -		.id            = 0,
> -		.of_compatible = "motorola,cpcap-led-red",
> -	}, {
> -		.name          = "cpcap-led",
> -		.id            = 1,
> -		.of_compatible = "motorola,cpcap-led-green",
> -	}, {
> -		.name          = "cpcap-led",
> -		.id            = 2,
> -		.of_compatible = "motorola,cpcap-led-blue",
> -	}, {
> -		.name          = "cpcap-led",
> -		.id            = 3,
> -		.of_compatible = "motorola,cpcap-led-adl",
> -	}, {
> -		.name          = "cpcap-led",
> -		.id            = 4,
> -		.of_compatible = "motorola,cpcap-led-cp",
> -	}, {
> -		.name          = "cpcap-codec",
> -	}
> +static const struct mfd_cell cpcap_default_mfd_devices[] = {
> +	MFD_CELL_OF("cpcap_adc", NULL, NULL, 0, 0, "motorola,cpcap-adc"),
> +	MFD_CELL_OF("cpcap_battery", NULL, NULL, 0, 0,
> +		    "motorola,cpcap-battery"),
> +	MFD_CELL_OF("cpcap-regulator", NULL, NULL, 0, 0,
> +		    "motorola,cpcap-regulator"),
> +	MFD_CELL_OF("cpcap-rtc", NULL, NULL, 0, 0, "motorola,cpcap-rtc"),
> +	MFD_CELL_OF("cpcap-pwrbutton", NULL, NULL, 0, 0,
> +		    "motorola,cpcap-pwrbutton"),
> +	MFD_CELL_OF("cpcap-usb-phy", NULL, NULL, 0, 0,
> +		    "motorola,cpcap-usb-phy"),
> +	MFD_CELL_OF("cpcap-led", NULL, NULL, 0, 0, "motorola,cpcap-led-red"),
> +	MFD_CELL_OF("cpcap-led", NULL, NULL, 0, 1, "motorola,cpcap-led-green"),
> +	MFD_CELL_OF("cpcap-led", NULL, NULL, 0, 2, "motorola,cpcap-led-blue"),
> +	MFD_CELL_OF("cpcap-led", NULL, NULL, 0, 3, "motorola,cpcap-led-adl"),
> +	MFD_CELL_OF("cpcap-led", NULL, NULL, 0, 4, "motorola,cpcap-led-cp"),
> +	MFD_CELL_NAME("cpcap-codec"),
> +};

Nit: I wouldn't complain if you wanted to have all of these on a single
line for neatness.

> +static const struct mfd_cell cpcap_mapphone_mfd_devices[] = {
> +	MFD_CELL_OF("cpcap_adc", NULL, NULL, 0, 0,
> +		    "motorola,mapphone-cpcap-adc"),
> +	MFD_CELL_OF("cpcap_battery", NULL, NULL, 0, 0,
> +		    "motorola,cpcap-battery"),
> +	MFD_CELL_OF("cpcap-charger", NULL, NULL, 0, 0,
> +		    "motorola,mapphone-cpcap-charger"),
> +	MFD_CELL_OF("cpcap-regulator", NULL, NULL, 0, 0,
> +		    "motorola,mapphone-cpcap-regulator"),
> +	MFD_CELL_OF("cpcap-rtc", NULL, NULL, 0, 0, "motorola,cpcap-rtc"),
> +	MFD_CELL_OF("cpcap-pwrbutton", NULL, NULL, 0, 0,
> +		    "motorola,cpcap-pwrbutton"),
> +	MFD_CELL_OF("cpcap-usb-phy", NULL, NULL, 0, 0,
> +		    "motorola,mapphone-cpcap-usb-phy"),
> +	MFD_CELL_OF("cpcap-led", NULL, NULL, 0, 0, "motorola,cpcap-led-red"),
> +	MFD_CELL_OF("cpcap-led", NULL, NULL, 0, 1, "motorola,cpcap-led-green"),
> +	MFD_CELL_OF("cpcap-led", NULL, NULL, 0, 2, "motorola,cpcap-led-blue"),
> +	MFD_CELL_OF("cpcap-led", NULL, NULL, 0, 3, "motorola,cpcap-led-adl"),
> +	MFD_CELL_OF("cpcap-led", NULL, NULL, 0, 4, "motorola,cpcap-led-cp"),
> +	MFD_CELL_NAME("cpcap-codec"),
>  };

A lot of these are duplicated, right?

I would have a comment set, then the differences in separate containers.

>  static int cpcap_probe(struct spi_device *spi)
>  {
>  	struct cpcap_ddata *cpcap;
> +	const struct mfd_cell *cells;
> +	unsigned int num_cells;
>  	int ret;
>  
>  	cpcap = devm_kzalloc(&spi->dev, sizeof(*cpcap), GFP_KERNEL);
>  	if (!cpcap)
>  		return -ENOMEM;
>  
> +	cpcap->variant = (enum cpcap_variant)spi_get_device_match_data(spi);
> +	if (!cpcap->variant)
> +		return -ENODEV;

Isn't this covered in the 'default' below?


> +	switch (cpcap->variant) {
> +	case CPCAP_DEFAULT:
> +		cells = cpcap_default_mfd_devices;
> +		num_cells = ARRAY_SIZE(cpcap_default_mfd_devices);
> +		break;
> +	case CPCAP_MAPPHONE:
> +		cells = cpcap_mapphone_mfd_devices;
> +		num_cells = ARRAY_SIZE(cpcap_mapphone_mfd_devices);
> +		break;
> +	default:
> +		return dev_err_probe(&spi->dev, -EINVAL,
> +				     "Unknown device %d\n", cpcap->variant);

This should be -ENODEV.

> +	}
> +
>  	cpcap->spi = spi;
>  	spi_set_drvdata(spi, cpcap);
>  
> @@ -331,10 +333,28 @@ static int cpcap_probe(struct spi_device *spi)
>  	spi->dev.coherent_dma_mask = 0;
>  	spi->dev.dma_mask = &spi->dev.coherent_dma_mask;
>  
> -	return devm_mfd_add_devices(&spi->dev, 0, cpcap_mfd_devices,
> -				    ARRAY_SIZE(cpcap_mfd_devices), NULL, 0, NULL);
> +	return devm_mfd_add_devices(&spi->dev, 0, cells, num_cells, NULL, 0, NULL);
>  }
>  
> +static const struct of_device_id cpcap_of_match[] = {
> +	{
> +		.compatible = "motorola,cpcap",
> +		.data = (void *)CPCAP_DEFAULT

Single line should be fine.

> +	}, {
> +		.compatible = "motorola,mapphone-cpcap",
> +		.data = (void *)CPCAP_MAPPHONE
> +	},
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, cpcap_of_match);
> +
> +static const struct spi_device_id cpcap_spi_ids[] = {
> +	{ "cpcap", CPCAP_DEFAULT },
> +	{ "mapphone-cpcap", CPCAP_MAPPHONE },
> +	{ /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(spi, cpcap_spi_ids);
> +
>  static struct spi_driver cpcap_driver = {
>  	.driver = {
>  		.name = "cpcap-core",
> diff --git a/include/linux/mfd/motorola-cpcap.h b/include/linux/mfd/motorola-cpcap.h
> index 981e5777deb7..1a85b06272c8 100644
> --- a/include/linux/mfd/motorola-cpcap.h
> +++ b/include/linux/mfd/motorola-cpcap.h
> @@ -25,6 +25,12 @@
>  #define CPCAP_REVISION_2_0	0x10
>  #define CPCAP_REVISION_2_1	0x11
>  
> +enum cpcap_variant {
> +	CPCAP_DEFAULT = 1,
> +	CPCAP_MAPPHONE,
> +	CPCAP_MAX
> +};
> +
>  /* CPCAP registers */
>  #define CPCAP_REG_INT1		0x0000	/* Interrupt 1 */
>  #define CPCAP_REG_INT2		0x0004	/* Interrupt 2 */
> -- 
> 2.51.0
> 

-- 
Lee Jones

  parent reply	other threads:[~2026-05-20 15:08 UTC|newest]

Thread overview: 20+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-05-10 11:07 [PATCH v5 0/6] mfd: cpcap: convert documentation to schema and add Mot board support Svyatoslav Ryhel
2026-05-10 11:07 ` [PATCH v5 1/6] dt-bindings: leds: leds-cpcap: convert to DT schema Svyatoslav Ryhel
2026-05-10 12:44   ` Rob Herring (Arm)
2026-05-10 11:08 ` [PATCH v5 2/6] dt-bindings: input: cpcap-pwrbutton: " Svyatoslav Ryhel
2026-05-10 12:44   ` Rob Herring (Arm)
2026-05-10 11:08 ` [PATCH v5 3/6] dt-bindings: mfd: motorola-cpcap: " Svyatoslav Ryhel
2026-05-11 21:19   ` sashiko-bot
2026-05-12 12:53   ` Rob Herring
2026-05-12 13:00     ` Svyatoslav Ryhel
2026-05-10 11:08 ` [PATCH v5 4/6] dt-bindings: mfd: motorola-cpcap: document Mapphone and Mot CPCAP Svyatoslav Ryhel
2026-05-11 21:37   ` sashiko-bot
2026-05-10 11:08 ` [PATCH v5 5/6] mfd: motorola-cpcap: diverge configuration per-board Svyatoslav Ryhel
2026-05-11 22:08   ` sashiko-bot
2026-05-20 15:07   ` Lee Jones [this message]
2026-05-20 15:29     ` Svyatoslav Ryhel
2026-05-20 16:05       ` Lee Jones
2026-05-20 16:30         ` Svyatoslav Ryhel
2026-05-20 17:02           ` Lee Jones
2026-05-20 17:25             ` Svyatoslav Ryhel
2026-05-10 11:08 ` [PATCH v5 6/6] mfd: motorola-cpcap: add support for Mot CPCAP composition Svyatoslav Ryhel

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260520150758.GG2767592@google.com \
    --to=lee@kernel.org \
    --cc=clamor95@gmail.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dlechner@baylibre.com \
    --cc=dmitry.torokhov@gmail.com \
    --cc=krzk+dt@kernel.org \
    --cc=linux-input@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-leds@vger.kernel.org \
    --cc=pavel@kernel.org \
    --cc=robh@kernel.org \
    --cc=tony@atomide.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox