* [PATCH v4 2/2] media: i2c: add Aptina MT9M113 1.3 Mpx SoC sensor driver
2026-06-06 8:17 [PATCH v4 0/2] media: i2c: add Aptina MT9M113 image sensor driver Herman van Hazendonk via B4 Relay
2026-06-06 8:17 ` [PATCH v4 1/2] dt-bindings: media: i2c: add aptina,mt9m113 Herman van Hazendonk via B4 Relay
@ 2026-06-06 8:17 ` Herman van Hazendonk via B4 Relay
2026-06-06 8:31 ` sashiko-bot
1 sibling, 1 reply; 4+ messages in thread
From: Herman van Hazendonk via B4 Relay @ 2026-06-06 8:17 UTC (permalink / raw)
To: Mauro Carvalho Chehab, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Sakari Ailus
Cc: linux-media, devicetree, linux-kernel, Herman van Hazendonk
From: Herman van Hazendonk <github.com@herrie.org>
Add a V4L2 subdev driver for the Aptina MT9M113 1.3 Megapixel SoC
image sensor (1280x1024 active pixel array) with on-chip ISP. The
sensor exposes:
- dual context operation: Context A (640x480 preview, binned) and
Context B (1280x1024 capture) selectable at runtime;
- single-lane MIPI CSI-2 output, YUV422 in UYVY or YUYV byte order
(the byte order is selected via the chroma/luma swap bit in
MODE_OUTPUT_FORMAT_{A,B});
- I2C MCU-indirect register access through the 0x098C/0x0990 page
indirection pair, in addition to the directly addressable
register space;
- V4L2 controls: H/V flip, color effects (none / mono / sepia /
negative / solarization), power-line frequency, saturation,
manual or auto exposure, analog gain, auto white balance, and
a four-entry test pattern selector;
- a 24 MHz EXTCLK and 1.8/2.8 V supplies.
The MT9M113 MCU intermittently wedges on stream start (SEQ_CMD
stuck, SEQ_STATE never reaching preview/capture; only a full power
cycle recovers it). The driver works around this in two layers:
runtime-PM resume always performs a full power-cycle plus init-table
replay - matching the legacy vendor kernel's per-open behaviour -
so a wedged MCU is recovered each session; and the s_stream(1) path
retries a bounded number of times with a runtime-PM power cycle
between attempts as fallback insurance for the residual failure
rate.
Found on the HP TouchPad (Tenderloin) as the front-facing camera
and on a number of other 1280x1024 mobile/embedded boards.
Assisted-by: Claude:claude-opus-4-7 Sashiko:claude-haiku-4-5
Signed-off-by: Herman van Hazendonk <github.com@herrie.org>
---
MAINTAINERS | 8 +
drivers/media/i2c/Kconfig | 12 +
drivers/media/i2c/Makefile | 1 +
drivers/media/i2c/mt9m113.c | 3114 +++++++++++++++++++++++++++++++++++++++++++
4 files changed, 3135 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 2fb1c75afd16..c1ca196180b0 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18165,6 +18165,14 @@ L: linux-mtd@lists.infradead.org
S: Maintained
F: drivers/mtd/devices/docg3*
+MT9M113 APTINA SENSOR DRIVER
+M: Herman van Hazendonk <github.com@herrie.org>
+L: linux-media@vger.kernel.org
+S: Maintained
+T: git git://linuxtv.org/media.git
+F: Documentation/devicetree/bindings/media/i2c/aptina,mt9m113.yaml
+F: drivers/media/i2c/mt9m113.c
+
MT9M114 ONSEMI SENSOR DRIVER
M: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
L: linux-media@vger.kernel.org
diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
index 8f2ba4121586..77c2e432578f 100644
--- a/drivers/media/i2c/Kconfig
+++ b/drivers/media/i2c/Kconfig
@@ -302,6 +302,18 @@ config VIDEO_MT9M111
This driver supports MT9M111, MT9M112 and MT9M131 cameras from
Micron/Aptina
+config VIDEO_MT9M113
+ tristate "Aptina MT9M113 sensor support"
+ select V4L2_CCI_I2C
+ help
+ This is a Video4Linux2 sensor driver for the Aptina MT9M113
+ 1.3 Megapixel CMOS camera sensor. The MT9M113 has dual context
+ support: Context A (640x480 preview) and Context B (1280x1024
+ capture).
+
+ To compile this driver as a module, choose M here: the
+ module will be called mt9m113.
+
config VIDEO_MT9M114
tristate "onsemi MT9M114 sensor support"
select V4L2_CCI_I2C
diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
index 90b276a7417a..f2ba184dd0e4 100644
--- a/drivers/media/i2c/Makefile
+++ b/drivers/media/i2c/Makefile
@@ -76,6 +76,7 @@ obj-$(CONFIG_VIDEO_ML86V7667) += ml86v7667.o
obj-$(CONFIG_VIDEO_MSP3400) += msp3400.o
obj-$(CONFIG_VIDEO_MT9M001) += mt9m001.o
obj-$(CONFIG_VIDEO_MT9M111) += mt9m111.o
+obj-$(CONFIG_VIDEO_MT9M113) += mt9m113.o
obj-$(CONFIG_VIDEO_MT9M114) += mt9m114.o
obj-$(CONFIG_VIDEO_MT9P031) += mt9p031.o
obj-$(CONFIG_VIDEO_MT9T112) += mt9t112.o
diff --git a/drivers/media/i2c/mt9m113.c b/drivers/media/i2c/mt9m113.c
new file mode 100644
index 000000000000..1b6480df8790
--- /dev/null
+++ b/drivers/media/i2c/mt9m113.c
@@ -0,0 +1,3114 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * mt9m113.c Aptina MT9M113 sensor driver
+ *
+ * Copyright (C) 2024 Herman van Hazendonk <github.com@herrie.org>
+ *
+ * MT9M113 is a 1.3MP SOC sensor with dual context support:
+ * Context A: 640x480 preview mode (binned)
+ * Context B: 1280x1024 capture mode (full resolution)
+ *
+ * Ported from legacy vendor kernel mt9m113.c/mt9m113_reg.c.
+ * Uses MCU indirect access (0x098C/0x0990) for configuration.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/math64.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/pm_runtime.h>
+#include <linux/property.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/types.h>
+#include <linux/videodev2.h>
+
+#include <media/v4l2-async.h>
+#include <media/v4l2-cci.h>
+#include <media/v4l2-ctrls.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-mediabus.h>
+#include <media/v4l2-subdev.h>
+
+/* Delay before enabling MIPI output, allowing CSIPHY to stabilize. */
+#define MT9M113_PRE_MIPI_DELAY_MS 10
+
+/*
+ * The MT9M113 MCU intermittently wedges on stream start (SEQ_CMD stuck,
+ * 0xa103 timeout, SEQ_STATE never reaching preview 0x04 / capture 0x07).
+ * The failures cluster at the start of a run and then clear, so a bounded
+ * retry that power-cycles the sensor between attempts reliably gets the
+ * stream up. 3 attempts is enough in practice (with the per-session
+ * runtime-PM re-init as the primary fix); a larger cap would stack
+ * power-cycle + ~600-entry init-table replay into a STREAMON latency
+ * userspace clients treat as a hang. Total attempts (1 initial + retries).
+ */
+#define MT9M113_STREAM_START_RETRIES 3
+
+/* MT9M113 chip ID */
+#define MT9M113_CHIP_ID CCI_REG16(0x0000)
+#define MT9M113_CHIP_ID_VALUE 0x2480
+
+/* Sysctl registers */
+#define MT9M113_PLL_DIVIDERS CCI_REG16(0x0010)
+#define MT9M113_PLL_P_DIVIDERS CCI_REG16(0x0012)
+#define MT9M113_PLL_CONTROL CCI_REG16(0x0014)
+#define MT9M113_CLOCKS_CONTROL CCI_REG16(0x0016)
+#define MT9M113_STANDBY_CONTROL CCI_REG16(0x0018)
+#define MT9M113_STANDBY_CONTROL_ACTIVE 0x0028 /* MCU running, not in standby */
+#define MT9M113_RESET_AND_MISC_CONTROL CCI_REG16(0x001a)
+#define MT9M113_RESET_SOC BIT(0)
+#define MT9M113_MCU_BOOT_MODE CCI_REG16(0x001c)
+
+/* MCU indirect access registers */
+#define MT9M113_MCU_ADDRESS CCI_REG16(0x098c)
+#define MT9M113_MCU_DATA CCI_REG16(0x0990)
+
+/* MCU variable addresses */
+#define MT9M113_SEQ_CMD 0xa103
+#define MT9M113_SEQ_CMD_RUN 0x0001
+#define MT9M113_SEQ_CMD_CAPTURE 0x0002
+#define MT9M113_SEQ_CMD_REFRESH 0x0005
+#define MT9M113_SEQ_CMD_REFRESH_MODE 0x0006
+#define MT9M113_SEQ_STATE 0xa104
+/*
+ * Per datasheet R0x0004 seq_state values: 0x02 = Enter preview, 0x03 =
+ * Preview (stable), 0x04 = Leave preview (transient, only seen while
+ * exiting preview for a context switch). 0x07 is stable Capture
+ * (Context B). The Context-B preview-first step must wait for the
+ * stable 0x03, not the transient 0x04 - waiting for 0x04 here misses
+ * the window and times out on every Context B stream-start.
+ */
+#define MT9M113_SEQ_STATE_PREVIEW 0x03
+#define MT9M113_SEQ_STATE_CAPTURE 0x07
+#define MT9M113_SEQ_CAP_MODE 0xa115
+#define MT9M113_SEQ_CAP_MODE_PREVIEW 0x0030 /* continuous preview */
+#define MT9M113_SEQ_CAP_MODE_VIDEO 0x0002 /* stay in Context B */
+
+/* Mode Output dimension/format MCU variables (Driver ID 7) */
+#define MT9M113_MODE_OUTPUT_WIDTH_A 0x2703
+#define MT9M113_MODE_OUTPUT_HEIGHT_A 0x2705
+#define MT9M113_MODE_OUTPUT_WIDTH_B 0x2707
+#define MT9M113_MODE_OUTPUT_HEIGHT_B 0x2709
+#define MT9M113_MODE_OUTPUT_FORMAT_A 0x2755
+#define MT9M113_MODE_OUTPUT_FORMAT_B 0x2757
+#define MT9M113_MODE_OUTPUT_FORMAT_YUV 0x0000
+/*
+ * YUV byte ordering (datasheet table 31 "mode_output_format_a/b"):
+ * default (0x0000) = Cb Y0 Cr Y1 = UYVY
+ * SWAP_LUMA_CHROMA = Y0 Cb Y1 Cr = YUYV
+ */
+#define MT9M113_MODE_OUTPUT_FORMAT_SWAP_LUMA_CHROMA BIT(1)
+
+/* Special effects MCU variables */
+#define MT9M113_MODE_SPEC_EFFECTS_A 0x2759
+#define MT9M113_MODE_SPEC_EFFECTS_B 0x275b
+#define MT9M113_SPEC_EFFECTS_DEFAULT 0x6440
+#define MT9M113_SPEC_EFFECTS_MASK 0x0007
+#define MT9M113_SPEC_EFFECTS_NONE 0x0000
+#define MT9M113_SPEC_EFFECTS_MONOCHROME 0x0001
+#define MT9M113_SPEC_EFFECTS_SEPIA 0x0002
+#define MT9M113_SPEC_EFFECTS_NEGATIVE 0x0003
+#define MT9M113_SPEC_EFFECTS_SOLARIZE 0x0004
+
+/* Sensor Read Mode MCU variables (for flip/mirror control) */
+#define MT9M113_SENSOR_READ_MODE_A 0x2717
+#define MT9M113_SENSOR_READ_MODE_B 0x272d
+#define MT9M113_SENSOR_READ_MODE_HMIRROR BIT(0)
+#define MT9M113_SENSOR_READ_MODE_VMIRROR BIT(1)
+
+/*
+ * Context A/B sensor configuration MCU variables
+ * These control the sensor readout window and must be re-applied when
+ * switching contexts to ensure correct line counts.
+ */
+#define MT9M113_MODE_SENSOR_ROW_START_A 0x270D
+#define MT9M113_MODE_SENSOR_COL_START_A 0x270F
+#define MT9M113_MODE_SENSOR_ROW_END_A 0x2711
+#define MT9M113_MODE_SENSOR_COL_END_A 0x2713
+#define MT9M113_MODE_SENSOR_ROW_SPEED_A 0x2715
+#define MT9M113_MODE_SENSOR_FRAME_LENGTH_A 0x271F
+#define MT9M113_MODE_SENSOR_LINE_LENGTH_PCK_A 0x2721
+
+#define MT9M113_MODE_SENSOR_ROW_START_B 0x2723
+#define MT9M113_MODE_SENSOR_COL_START_B 0x2725
+#define MT9M113_MODE_SENSOR_ROW_END_B 0x2727
+#define MT9M113_MODE_SENSOR_COL_END_B 0x2729
+#define MT9M113_MODE_SENSOR_ROW_SPEED_B 0x272B
+#define MT9M113_MODE_SENSOR_FRAME_LENGTH_B 0x2735
+#define MT9M113_MODE_SENSOR_LINE_LENGTH_PCK_B 0x2737
+
+/* Context A sensor config values (from legacy vendor driver, 640x480 binned) */
+#define MT9M113_CONTEXT_A_ROW_START 0x0000
+#define MT9M113_CONTEXT_A_COL_START 0x0000
+#define MT9M113_CONTEXT_A_ROW_END 0x03CD /* 973 */
+#define MT9M113_CONTEXT_A_COL_END 0x050D /* 1293 */
+#define MT9M113_CONTEXT_A_ROW_SPEED 0x2111
+#define MT9M113_CONTEXT_A_READ_MODE 0x046C /* Binning enabled */
+#define MT9M113_CONTEXT_A_FRAME_LENGTH 0x032E /* 814 lines (incl vblank) */
+#define MT9M113_CONTEXT_A_LINE_LENGTH_PCK 0x04CC /* 1228 pixclks/line */
+
+/* Context B sensor config values (from legacy vendor driver, 1280x1024 full res) */
+#define MT9M113_CONTEXT_B_ROW_START 0x0004
+#define MT9M113_CONTEXT_B_COL_START 0x0004
+#define MT9M113_CONTEXT_B_ROW_END 0x040B /* 1035 */
+#define MT9M113_CONTEXT_B_COL_END 0x050B /* 1291 */
+#define MT9M113_CONTEXT_B_ROW_SPEED 0x2111
+#define MT9M113_CONTEXT_B_READ_MODE 0x0024 /* Full resolution */
+#define MT9M113_CONTEXT_B_FRAME_LENGTH 0x0559 /* 1369 lines (incl vblank) */
+#define MT9M113_CONTEXT_B_LINE_LENGTH_PCK 0x0722 /* 1826 pixclks/line */
+
+/* Auto Exposure MCU variables (for preview vs snapshot optimization) */
+#define MT9M113_AE_MAX_INDEX 0xa20c
+#define MT9M113_AE_MAX_VIRTGAIN 0xa20e
+#define MT9M113_AE_MAX_DGAIN_AE1 0xa21a
+#define MT9M113_AE_JUMP_DIVISOR 0xa21c
+#define MT9M113_AE_SKIP_FRAMES 0xa21e
+
+/* Flicker detection MCU variable */
+#define MT9M113_FD_MODE 0xa404
+#define MT9M113_FD_MODE_DISABLED 0x00
+#define MT9M113_FD_MODE_50HZ 0x01
+#define MT9M113_FD_MODE_60HZ 0x02
+#define MT9M113_FD_MODE_AUTO 0x03
+
+/* AWB/Color MCU variables */
+#define MT9M113_AWB_SATURATION 0xa354
+#define MT9M113_AWB_MODE 0xa34a
+
+/* Test pattern MCU variables (mode_common_mode_settings) */
+#define MT9M113_CAM_MODE_SELECT 0xc84c
+#define MT9M113_CAM_MODE_SELECT_NORMAL 0x00
+
+/*
+ * Test pattern register (Driver 7 R0x0066 mode_common_mode_settings_test_mode,
+ * MT9M113 datasheet "Table 31: Driver ID = 7: Mode Variables"). MCU logical
+ * addresses are NOT a clean (driver_id << 12) | offset encoding - each
+ * driver has its own hardcoded base page set by the chip firmware. Driver 7
+ * Mode variables share base 0x2700 (see MT9M113_MODE_OUTPUT_WIDTH_A = 0x2703
+ * for R0x0003, MT9M113_MODE_SPEC_EFFECTS_A = 0x2759 for R0x0059, etc.), so
+ * R0x0066 maps to 0x2766.
+ *
+ * Per the datasheet "Test Pattern Generator. Changes take effect only
+ * after REFRESH command", so writes are paired with mt9m113_refresh()
+ * when streaming. The datasheet also recommends disabling the MCU before
+ * enabling test patterns (BOOT_MODE=1 halt), which
+ * mt9m113_apply_test_pattern() performs after the REFRESH succeeds.
+ *
+ * Do NOT go via the CAM_MODE driver's test-pattern knob (CAM_MODE_SELECT =
+ * 0x02 TEST_PATTERN + CAM_MODE_TEST_PATTERN_SELECT in Driver 8): switching
+ * CAM_MODE into TEST_PATTERN mode wedges the sequencer so SEQ_CMD never
+ * processes REFRESH and stream_on() hangs.
+ *
+ * NOTE: forensic investigation on observed silicon shows the IFP TPG MUX
+ * does NOT actually engage despite mode_test_mode accepting every value:
+ *
+ * - R0x2766 (mode_test_mode) is a read/write logical variable, but the
+ * MCU firmware resets it to a default (0x8e8e) on every standby wake.
+ * - Hardware registers associated with the TPG MUX (R0x3246-R0x3252)
+ * are non-responsive dead zones, and bit 4 of R0x321C is hardwired
+ * to 0 - both classic Aptina foundry-removal fingerprints.
+ * - No raw sensor-core TPG (R0x3070-R0x3071) is present.
+ * - Confirmed by stripping the color pipeline (R0x3210=0) and
+ * verifying that even in a "naked" IFP state the live sensor data
+ * persists without any pattern injection.
+ *
+ * The V4L2_CID_TEST_PATTERN plumbing below is intentionally retained on
+ * the (faint) chance a different silicon variant or vendor SROM patch
+ * actually wires up the TPG block. Setting test_pattern > 0 on the
+ * current die is harmless - the writes succeed but no pattern appears.
+ */
+#define MT9M113_MODE_TEST_MODE 0x2766
+#define MT9M113_TEST_MODE_DISABLED 0x00
+#define MT9M113_TEST_MODE_SOLID_WHITE 0x01
+#define MT9M113_TEST_MODE_GREY_RAMP 0x02
+#define MT9M113_TEST_MODE_COLOR_BAR_RAMP 0x03
+#define MT9M113_TEST_MODE_SOLID_WHITE_COLOR_BARS 0x04
+#define MT9M113_TEST_MODE_NOISE 0x05
+
+/* Double buffer control register */
+#define MT9M113_DOUBLE_BUFFER_CONTROL CCI_REG16(0x0248)
+#define MT9M113_DOUBLE_BUFFER_SUSPEND BIT(15)
+
+/* Auto Exposure MCU variables */
+#define MT9M113_AE_GATE 0xa207
+#define MT9M113_AE_GATE_ENABLE 0x0000
+#define MT9M113_AE_GATE_DISABLE 0x00FF
+
+/* Sensor core exposure/gain registers */
+#define MT9M113_COARSE_IT_TIME_A CCI_REG16(0x3012)
+#define MT9M113_COARSE_IT_TIME_B CCI_REG16(0x3014)
+#define MT9M113_ANALOG_GAIN CCI_REG16(0x3028)
+
+/* Sensor core registers */
+#define MT9M113_RESET_REGISTER CCI_REG16(0x301a)
+#define MT9M113_RESET_REG_STREAMING 0x120C
+#define MT9M113_OFIFO_CONTROL_STATUS CCI_REG16(0x321c)
+#define MT9M113_OFIFO_BYPASS 0x0003 /* FIFO bypass (YUV path) */
+
+/* Color pipeline (ISP) control */
+#define MT9M113_COLOR_PIPELINE_CONTROL CCI_REG16(0x3210)
+#define MT9M113_COLOR_PIPELINE_DEFAULT 0x01b8 /* scaler+gamma+ap+shading */
+
+/* OUTPUT_CONTROL register (0x3400) - MIPI control */
+#define MT9M113_OUTPUT_CONTROL CCI_REG16(0x3400)
+#define MT9M113_OUTPUT_CONTROL_MIPI_ENABLE 0x7A08 /* YUV422 dt=0x1E */
+
+/* CUSTOM_SHORT_PKT register */
+#define MT9M113_CUSTOM_SHORT_PKT CCI_REG16(0x3404)
+#define MT9M113_CUSTOM_SHORT_PKT_FRAME_CNT_EN 0x0080
+
+/* Pixel array dimensions */
+#define MT9M113_PIXEL_ARRAY_WIDTH 1296U
+#define MT9M113_PIXEL_ARRAY_HEIGHT 1040U
+
+/* -----------------------------------------------------------------------------
+ * Data Structures
+ */
+
+struct mt9m113_format_info {
+ u32 code;
+};
+
+struct mt9m113 {
+ struct i2c_client *client;
+ struct regmap *regmap;
+
+ struct clk *clk;
+ struct gpio_desc *reset;
+ struct gpio_desc *powerdown;
+ struct regulator_bulk_data supplies[3];
+ struct v4l2_fwnode_endpoint bus_cfg;
+
+ unsigned int pixrate;
+ s64 link_freq;
+ bool streaming;
+ bool test_pattern_active;
+ u8 test_pattern_value; /* last V4L2_CID_TEST_PATTERN menu index */
+
+ /* Pixel Array sub-device */
+ struct {
+ struct v4l2_subdev sd;
+ struct media_pad pad;
+ struct v4l2_ctrl_handler hdl;
+ } pa;
+
+ /* Image Flow Processor sub-device */
+ struct {
+ struct v4l2_subdev sd;
+ struct media_pad pads[2];
+
+ struct v4l2_ctrl_handler hdl;
+ } ifp;
+};
+
+/* -----------------------------------------------------------------------------
+ * Formats
+ */
+
+/*
+ * Source-pad output formats. Only YUV422 is exposed: MT9M113_OUTPUT_CONTROL
+ * advertises the YUV422 CSI-2 data type (0x1E) unconditionally on the wire,
+ * and adding RGB565 would require also driving the matching CSI-2 dt (0x22)
+ * out of OUTPUT_CONTROL — verifying the exact bit layout for that needs the
+ * sensor datasheet and a hardware re-test, so RGB is deferred to a follow-up.
+ */
+static const struct mt9m113_format_info mt9m113_format_infos[] = {
+ { .code = MEDIA_BUS_FMT_UYVY8_1X16 },
+ { .code = MEDIA_BUS_FMT_YUYV8_1X16 },
+};
+
+static const struct mt9m113_format_info *
+mt9m113_format_info(u32 code)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(mt9m113_format_infos); i++) {
+ if (mt9m113_format_infos[i].code == code)
+ return &mt9m113_format_infos[i];
+ }
+
+ return &mt9m113_format_infos[0];
+}
+
+/*
+ * Map a V4L2 mbus code to the value programmed into MODE_OUTPUT_FORMAT_{A,B}.
+ * Driving the chroma/luma swap bit is what differentiates UYVY from YUYV;
+ * without it both codes would emit the same bytes on the MIPI bus.
+ */
+static u16 mt9m113_format_val(u32 code)
+{
+ switch (code) {
+ case MEDIA_BUS_FMT_YUYV8_1X16:
+ return MT9M113_MODE_OUTPUT_FORMAT_YUV |
+ MT9M113_MODE_OUTPUT_FORMAT_SWAP_LUMA_CHROMA;
+ case MEDIA_BUS_FMT_UYVY8_1X16:
+ default:
+ return MT9M113_MODE_OUTPUT_FORMAT_YUV;
+ }
+}
+
+/* -----------------------------------------------------------------------------
+ * MCU Variable Access Helpers
+ */
+
+static int mt9m113_write_mcu_var(struct mt9m113 *sensor, u16 addr, u16 value)
+{
+ int ret = 0;
+
+ cci_write(sensor->regmap, MT9M113_MCU_ADDRESS, addr, &ret);
+ cci_write(sensor->regmap, MT9M113_MCU_DATA, value, &ret);
+ return ret;
+}
+
+static int mt9m113_read_mcu_var(struct mt9m113 *sensor, u16 addr, u64 *value)
+{
+ int ret;
+
+ ret = cci_write(sensor->regmap, MT9M113_MCU_ADDRESS, addr, NULL);
+ if (ret)
+ return ret;
+ return cci_read(sensor->regmap, MT9M113_MCU_DATA, value, NULL);
+}
+
+static int mt9m113_poll_mcu_var(struct mt9m113 *sensor, u16 addr,
+ u16 expected, unsigned int timeout_ms)
+{
+ unsigned int i;
+ u64 value = 0;
+ int ret;
+
+ for (i = 0; i < timeout_ms / 10; i++) {
+ ret = mt9m113_read_mcu_var(sensor, addr, &value);
+ if (ret < 0)
+ return ret;
+ if (value == expected)
+ return 0;
+ usleep_range(10000, 11000);
+ }
+
+ dev_err(&sensor->client->dev,
+ "MCU var 0x%04x timeout (got 0x%llx, expected 0x%04x)\n",
+ addr, value, expected);
+ return -ETIMEDOUT;
+}
+
+/*
+ * Ensure MCU sequencer is idle before issuing a new command.
+ * This prevents cascading failures where a timed-out command
+ * causes subsequent commands to also fail.
+ */
+static int mt9m113_seq_cmd_ready(struct mt9m113 *sensor)
+{
+ u64 seq_cmd;
+ int ret;
+
+ ret = mt9m113_read_mcu_var(sensor, MT9M113_SEQ_CMD, &seq_cmd);
+ if (ret < 0)
+ return ret;
+
+ if (seq_cmd == 0)
+ return 0; /* Already idle */
+
+ /*
+ * A previous command is still pending. This can happen if:
+ * 1. Previous streaming start failed mid-way
+ * 2. The MCU is slow to process a command
+ *
+ * Wait up to 2 seconds for it to complete. This is longer than
+ * normal command timeouts to handle recovery scenarios.
+ */
+ dev_dbg(&sensor->client->dev,
+ "MT9M113: SEQ_CMD=0x%llx, waiting for idle\n", seq_cmd);
+
+ return mt9m113_poll_mcu_var(sensor, MT9M113_SEQ_CMD, 0x0000, 2000);
+}
+
+/*
+ * mt9m113_refresh - Issue REFRESH_MODE + REFRESH sequence
+ *
+ * Per datasheet: "It is recommended that refresh and refresh mode commands
+ * always be run together, and that refresh mode should be issued BEFORE
+ * the refresh command."
+ */
+static int mt9m113_refresh(struct mt9m113 *sensor)
+{
+ int ret;
+
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_SEQ_CMD,
+ MT9M113_SEQ_CMD_REFRESH_MODE);
+ if (ret)
+ return ret;
+
+ ret = mt9m113_poll_mcu_var(sensor, MT9M113_SEQ_CMD, 0x0000, 500);
+ if (ret < 0)
+ dev_warn(&sensor->client->dev, "MT9M113: REFRESH_MODE timeout\n");
+
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_SEQ_CMD,
+ MT9M113_SEQ_CMD_REFRESH);
+ if (ret)
+ return ret;
+
+ ret = mt9m113_poll_mcu_var(sensor, MT9M113_SEQ_CMD, 0x0000, 500);
+ if (ret < 0)
+ dev_warn(&sensor->client->dev, "MT9M113: REFRESH timeout\n");
+
+ return 0;
+}
+
+/*
+ * Re-program SENSOR_READ_MODE_{A,B} for the context geometry while keeping
+ * the live HFLIP/VFLIP bits, which the V4L2 control handler has already
+ * applied via s_ctrl(). Writing CONTEXT_X_READ_MODE blindly would clear
+ * mirror bits 0/1 and silently undo the user's flip on first stream-start.
+ */
+static int mt9m113_apply_read_mode(struct mt9m113 *sensor, u16 reg, u16 base)
+{
+ const u16 mirror_mask = MT9M113_SENSOR_READ_MODE_HMIRROR |
+ MT9M113_SENSOR_READ_MODE_VMIRROR;
+ u64 cur = 0;
+ int ret;
+
+ ret = mt9m113_read_mcu_var(sensor, reg, &cur);
+ if (ret)
+ return ret;
+
+ return mt9m113_write_mcu_var(sensor, reg,
+ (base & ~mirror_mask) |
+ ((u16)cur & mirror_mask));
+}
+
+/**
+ * mt9m113_configure_sensor_context - Configure sensor readout parameters
+ * @sensor: MT9M113 sensor device
+ * @use_context_b: true for Context B (1280x1024), false for Context A (640x480)
+ *
+ * Re-applies the sensor configuration registers for the selected context.
+ * This is necessary because the MT9M113's MCU variables can become corrupted
+ * or stale after switching between contexts. Without explicitly re-writing
+ * these values, Context A may use incorrect row_end and read_mode values
+ * after running Context B, resulting in wrong line counts and corrupted images.
+ *
+ * Must be called before mt9m113_refresh() to ensure the new values take effect.
+ */
+static int mt9m113_configure_sensor_context(struct mt9m113 *sensor,
+ bool use_context_b)
+{
+ struct device *dev = &sensor->client->dev;
+ int ret;
+
+ if (use_context_b) {
+ /* Context B: 1280x1024 full resolution */
+ dev_dbg(dev, "MT9M113: Configuring Context B sensor params\n");
+
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_ROW_START_B,
+ MT9M113_CONTEXT_B_ROW_START);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_COL_START_B,
+ MT9M113_CONTEXT_B_COL_START);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_ROW_END_B,
+ MT9M113_CONTEXT_B_ROW_END);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_COL_END_B,
+ MT9M113_CONTEXT_B_COL_END);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_ROW_SPEED_B,
+ MT9M113_CONTEXT_B_ROW_SPEED);
+ if (ret)
+ return ret;
+ ret = mt9m113_apply_read_mode(sensor,
+ MT9M113_SENSOR_READ_MODE_B,
+ MT9M113_CONTEXT_B_READ_MODE);
+ if (ret)
+ return ret;
+ /*
+ * Frame/line length define the total frame period (active +
+ * blanking). They must be re-applied with the rest of the
+ * context geometry: the VFE CAMIF counts lines to find frame
+ * boundaries (no MIPI FE short packet), so a stale period makes
+ * the captured image walk vertically frame-over-frame.
+ */
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_FRAME_LENGTH_B,
+ MT9M113_CONTEXT_B_FRAME_LENGTH);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_LINE_LENGTH_PCK_B,
+ MT9M113_CONTEXT_B_LINE_LENGTH_PCK);
+ if (ret)
+ return ret;
+ } else {
+ /* Context A: 640x480 binned preview */
+ dev_dbg(dev, "MT9M113: Configuring Context A sensor params\n");
+
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_ROW_START_A,
+ MT9M113_CONTEXT_A_ROW_START);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_COL_START_A,
+ MT9M113_CONTEXT_A_COL_START);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_ROW_END_A,
+ MT9M113_CONTEXT_A_ROW_END);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_COL_END_A,
+ MT9M113_CONTEXT_A_COL_END);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_ROW_SPEED_A,
+ MT9M113_CONTEXT_A_ROW_SPEED);
+ if (ret)
+ return ret;
+ ret = mt9m113_apply_read_mode(sensor,
+ MT9M113_SENSOR_READ_MODE_A,
+ MT9M113_CONTEXT_A_READ_MODE);
+ if (ret)
+ return ret;
+ /* See Context B above: frame period must track the geometry. */
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_FRAME_LENGTH_A,
+ MT9M113_CONTEXT_A_FRAME_LENGTH);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SENSOR_LINE_LENGTH_PCK_A,
+ MT9M113_CONTEXT_A_LINE_LENGTH_PCK);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * Double Buffer Control
+ *
+ * The MT9M113 uses double buffering for context parameters. Setting bit 15
+ * of register 0x0248 suspends updates from shadow to active registers,
+ * allowing atomic multi-register configuration changes.
+ */
+
+static int mt9m113_double_buffer_suspend(struct mt9m113 *sensor)
+{
+ u64 value;
+ int ret;
+
+ ret = cci_read(sensor->regmap, MT9M113_DOUBLE_BUFFER_CONTROL, &value, NULL);
+ if (ret)
+ return ret;
+
+ value |= MT9M113_DOUBLE_BUFFER_SUSPEND;
+ return cci_write(sensor->regmap, MT9M113_DOUBLE_BUFFER_CONTROL, value, NULL);
+}
+
+static int mt9m113_double_buffer_resume(struct mt9m113 *sensor)
+{
+ u64 value;
+ int ret;
+
+ ret = cci_read(sensor->regmap, MT9M113_DOUBLE_BUFFER_CONTROL, &value, NULL);
+ if (ret)
+ return ret;
+
+ value &= ~MT9M113_DOUBLE_BUFFER_SUSPEND;
+ return cci_write(sensor->regmap, MT9M113_DOUBLE_BUFFER_CONTROL, value, NULL);
+}
+
+/* -----------------------------------------------------------------------------
+ * Initialization Table (from legacy vendor kernel mt9m113_reg.c)
+ */
+
+struct mt9m113_reg_entry {
+ u16 reg;
+ u16 value;
+ u16 delay_ms;
+};
+
+static const struct mt9m113_reg_entry mt9m113_init_table[] = {
+ /* OFIFO control */
+ { 0x321C, 0x0003, 0 },
+
+ /* Context A output (640x480 preview) */
+ { 0x098C, 0x2703, 0 },
+ { 0x0990, 0x0280, 0 },
+ { 0x098C, 0x2705, 0 },
+ { 0x0990, 0x01E0, 0 },
+
+ /* Context B output (1280x1024 capture) */
+ { 0x098C, 0x2707, 0 },
+ { 0x0990, 0x0500, 0 },
+ { 0x098C, 0x2709, 0 },
+ { 0x0990, 0x0400, 0 },
+
+ /* Context A sensor configuration */
+ { 0x098C, 0x270D, 0 },
+ { 0x0990, 0x0000, 0 },
+ { 0x098C, 0x270F, 0 },
+ { 0x0990, 0x0000, 0 },
+ { 0x098C, 0x2711, 0 }, /* MODE_SENSOR_ROW_END_A */
+ { 0x0990, 0x03CD, 0 }, /* 973 (from legacy vendor driver) */
+ { 0x098C, 0x2713, 0 },
+ { 0x0990, 0x050D, 0 },
+ { 0x098C, 0x2715, 0 },
+ { 0x0990, 0x2111, 0 },
+ { 0x098C, 0x2717, 0 },
+ { 0x0990, 0x046C, 0 },
+ { 0x098C, 0x2719, 0 },
+ { 0x0990, 0x00AC, 0 },
+ { 0x098C, 0x271B, 0 },
+ { 0x0990, 0x01F1, 0 },
+ { 0x098C, 0x271D, 0 },
+ { 0x0990, 0x013F, 0 },
+ { 0x098C, 0x271F, 0 },
+ { 0x0990, 0x032E, 0 },
+ { 0x098C, 0x2721, 0 },
+ { 0x0990, 0x04CC, 0 },
+
+ /* Context B sensor configuration */
+ { 0x098C, 0x2723, 0 },
+ { 0x0990, 0x0004, 0 },
+ { 0x098C, 0x2725, 0 },
+ { 0x0990, 0x0004, 0 },
+ { 0x098C, 0x2727, 0 },
+ { 0x0990, 0x040B, 0 },
+ { 0x098C, 0x2729, 0 },
+ { 0x0990, 0x050B, 0 },
+ { 0x098C, 0x272B, 0 },
+ { 0x0990, 0x2111, 0 },
+ { 0x098C, 0x272D, 0 },
+ { 0x0990, 0x0024, 0 },
+ { 0x098C, 0x272F, 0 },
+ { 0x0990, 0x004C, 0 },
+ { 0x098C, 0x2731, 0 },
+ { 0x0990, 0x00F9, 0 },
+ { 0x098C, 0x2733, 0 },
+ { 0x0990, 0x00A7, 0 },
+ { 0x098C, 0x2735, 0 },
+ { 0x0990, 0x0559, 0 },
+ { 0x098C, 0x2737, 0 },
+ { 0x0990, 0x0722, 0 },
+
+ /* Crop configuration - Context A */
+ { 0x098C, 0x2739, 0 },
+ { 0x0990, 0x0000, 0 },
+ { 0x098C, 0x273B, 0 },
+ { 0x0990, 0x027F, 0 },
+ { 0x098C, 0x273D, 0 },
+ { 0x0990, 0x0000, 0 },
+ { 0x098C, 0x273F, 0 },
+ { 0x0990, 0x01DF, 0 },
+
+ /* Crop configuration - Context B */
+ { 0x098C, 0x2747, 0 },
+ { 0x0990, 0x0000, 0 },
+ { 0x098C, 0x2749, 0 },
+ { 0x0990, 0x04FF, 0 },
+ { 0x098C, 0x274B, 0 },
+ { 0x0990, 0x0000, 0 },
+ { 0x098C, 0x274D, 0 },
+ { 0x0990, 0x03FF, 0 },
+
+ /* Flicker detection */
+ { 0x098C, 0x222D, 0 },
+ { 0x0990, 0x00CC, 0 },
+ { 0x098C, 0xA404, 0 },
+ { 0x0990, 0x0010, 0 },
+ { 0x098C, 0xA408, 0 },
+ { 0x0990, 0x0032, 0 },
+ { 0x098C, 0xA409, 0 },
+ { 0x0990, 0x0034, 0 },
+ { 0x098C, 0xA40A, 0 },
+ { 0x0990, 0x003C, 0 },
+ { 0x098C, 0xA40B, 0 },
+ { 0x0990, 0x003E, 0 },
+ { 0x098C, 0x2411, 0 },
+ { 0x0990, 0x00CC, 0 },
+ { 0x098C, 0x2413, 0 },
+ { 0x0990, 0x00F4, 0 },
+ { 0x098C, 0x2415, 0 },
+ { 0x0990, 0x0089, 0 },
+ { 0x098C, 0x2417, 0 },
+ { 0x0990, 0x00A4, 0 },
+ { 0x098C, 0xA40D, 0 },
+ { 0x0990, 0x0002, 0 },
+ { 0x098C, 0xA40E, 0 },
+ { 0x0990, 0x0003, 0 },
+ { 0x098C, 0xA410, 0 },
+ { 0x0990, 0x000A, 0 },
+
+ /* Sensor core reserved registers */
+ { 0x3044, 0x0504, 0 },
+ { 0x3086, 0x24F7, 0 },
+ { 0x3088, 0xF059, 0 },
+ { 0x3090, 0x0716, 0 },
+ { 0x3092, 0xAB1F, 0 },
+ { 0x30D4, 0x9020, 0 },
+ { 0x30E2, 0x6645, 0 },
+ { 0x30E4, 0x7A66, 0 },
+ { 0x30E6, 0x6652, 0 },
+ { 0x30E8, 0x7766, 0 },
+ { 0x30EA, 0x2E03, 0 },
+ { 0x30EC, 0x452E, 0 },
+ { 0x30EE, 0x2E17, 0 },
+ { 0x30F0, 0x452E, 0 },
+ { 0x30F6, 0x0501, 0 },
+ { 0x30F8, 0x0501, 0 },
+ { 0x30FA, 0x0401, 0 },
+ { 0x30FC, 0x0401, 0 },
+ { 0x30FE, 0x5145, 0 },
+ { 0x3100, 0x4F45, 0 },
+ { 0x3102, 0x652E, 0 },
+ { 0x3104, 0x7552, 0 },
+ { 0x3106, 0x2D05, 0 },
+ { 0x3108, 0x4405, 0 },
+ { 0x311A, 0x5045, 0 },
+ { 0x311E, 0x0601, 0 },
+ { 0x3122, 0x0601, 0 },
+ { 0x316C, 0x8406, 0 },
+
+ /* Noise reduction */
+ { 0x098C, 0xAB2D, 0 },
+ { 0x0990, 0x002A, 0 },
+ { 0x098C, 0xAB31, 0 },
+ { 0x0990, 0x002E, 0 },
+
+ /* Low-light enhancement */
+ { 0x098C, 0x2B28, 0 },
+ { 0x0990, 0x1F40, 0 },
+ { 0x098C, 0x2B2A, 0 },
+ { 0x0990, 0x3A98, 0 },
+ { 0x098C, 0x2B38, 0 },
+ { 0x0990, 0x1F40, 0 },
+ { 0x098C, 0x2B3A, 0 },
+ { 0x0990, 0x3A98, 0 },
+
+ /* AE settings */
+ { 0x098C, 0x2257, 0 },
+ { 0x0990, 0x2710, 0 },
+ { 0x098C, 0x2250, 0 },
+ { 0x0990, 0x1B58, 0 },
+ { 0x098C, 0x2252, 0 },
+ { 0x0990, 0x32C8, 0 },
+ { 0x098C, 0xA24B, 0 },
+ { 0x0990, 0x0082, 0 },
+
+ /* Aperture */
+ { 0x326C, 0x0C00, 0 },
+
+ /* More Context A settings */
+ { 0x098C, 0x2717, 0 },
+ { 0x0990, 0x046C, 0 },
+ { 0x098C, 0x2719, 0 },
+ { 0x0990, 0x00AC, 0 },
+ { 0x098C, 0x271B, 0 },
+ { 0x0990, 0x01F1, 0 },
+ { 0x098C, 0x271D, 0 },
+ { 0x0990, 0x013F, 0 },
+ { 0x098C, 0x271F, 0 },
+ { 0x0990, 0x032E, 0 },
+ { 0x098C, 0x2721, 0 },
+ { 0x0990, 0x04CC, 0 },
+ { 0x098C, 0x275F, 0 },
+ { 0x0990, 0x0596, 0 },
+ { 0x098C, 0x2761, 0 },
+ { 0x0990, 0x0094, 0 },
+
+ /* Lens shading correction */
+ { 0x364E, 0x07B0, 0 },
+ { 0x3650, 0x7E0E, 0 },
+ { 0x3652, 0x3D31, 0 },
+ { 0x3654, 0x80AE, 0 },
+ { 0x3656, 0xE131, 0 },
+ { 0x3658, 0x01B0, 0 },
+ { 0x365A, 0x878D, 0 },
+ { 0x365C, 0x2671, 0 },
+ { 0x365E, 0x7D2D, 0 },
+ { 0x3660, 0xA5D1, 0 },
+ { 0x3662, 0x03B0, 0 },
+ { 0x3664, 0x5A0E, 0 },
+ { 0x3666, 0x0E71, 0 },
+ { 0x3668, 0x99EE, 0 },
+ { 0x366A, 0xA671, 0 },
+ { 0x366C, 0x0170, 0 },
+ { 0x366E, 0xF44D, 0 },
+ { 0x3670, 0x2971, 0 },
+ { 0x3672, 0x2D4A, 0 },
+ { 0x3674, 0xD671, 0 },
+ { 0x3676, 0x674C, 0 },
+ { 0x3678, 0x748D, 0 },
+ { 0x367A, 0x3FEE, 0 },
+ { 0x367C, 0x89AE, 0 },
+ { 0x367E, 0xB410, 0 },
+ { 0x3680, 0x168C, 0 },
+ { 0x3682, 0xC56D, 0 },
+ { 0x3684, 0x7CAC, 0 },
+ { 0x3686, 0x038F, 0 },
+ { 0x3688, 0xA86F, 0 },
+ { 0x368A, 0xDB6B, 0 },
+ { 0x368C, 0xA2AE, 0 },
+ { 0x368E, 0xFA8D, 0 },
+ { 0x3690, 0x5C8E, 0 },
+ { 0x3692, 0x740C, 0 },
+ { 0x3694, 0x9F4B, 0 },
+ { 0x3696, 0x1C4D, 0 },
+ { 0x3698, 0x978D, 0 },
+ { 0x369A, 0x21EC, 0 },
+ { 0x369C, 0xF5AD, 0 },
+ { 0x369E, 0x7D10, 0 },
+ { 0x36A0, 0x3E2E, 0 },
+ { 0x36A2, 0x8953, 0 },
+ { 0x36A4, 0xD910, 0 },
+ { 0x36A6, 0x3033, 0 },
+ { 0x36A8, 0x06D1, 0 },
+ { 0x36AA, 0xAD4E, 0 },
+ { 0x36AC, 0xD2D2, 0 },
+ { 0x36AE, 0x5CCE, 0 },
+ { 0x36B0, 0x3B93, 0 },
+ { 0x36B2, 0x50D0, 0 },
+ { 0x36B4, 0x79AD, 0 },
+ { 0x36B6, 0xDFF2, 0 },
+ { 0x36B8, 0x88AF, 0 },
+ { 0x36BA, 0x2453, 0 },
+ { 0x36BC, 0x0051, 0 },
+ { 0x36BE, 0x81CF, 0 },
+ { 0x36C0, 0x8313, 0 },
+ { 0x36C2, 0x2250, 0 },
+ { 0x36C4, 0x4A53, 0 },
+ { 0x36C6, 0x0C8D, 0 },
+ { 0x36C8, 0x362B, 0 },
+ { 0x36CA, 0xAD51, 0 },
+ { 0x36CC, 0xA470, 0 },
+ { 0x36CE, 0x3DD2, 0 },
+ { 0x36D0, 0x174C, 0 },
+ { 0x36D2, 0x152F, 0 },
+ { 0x36D4, 0x82F1, 0 },
+ { 0x36D6, 0xDED0, 0 },
+ { 0x36D8, 0x6F12, 0 },
+ { 0x36DA, 0xD36C, 0 },
+ { 0x36DC, 0x51AE, 0 },
+ { 0x36DE, 0xD0AE, 0 },
+ { 0x36E0, 0x274E, 0 },
+ { 0x36E2, 0x25F2, 0 },
+ { 0x36E4, 0xDCCA, 0 },
+ { 0x36E6, 0x438E, 0 },
+ { 0x36E8, 0xD64E, 0 },
+ { 0x36EA, 0x8A71, 0 },
+ { 0x36EC, 0x1492, 0 },
+ { 0x36EE, 0xD5B1, 0 },
+ { 0x36F0, 0xEBF0, 0 },
+ { 0x36F2, 0x53F3, 0 },
+ { 0x36F4, 0x3492, 0 },
+ { 0x36F6, 0x9AF4, 0 },
+ { 0x36F8, 0x8BF1, 0 },
+ { 0x36FA, 0x204F, 0 },
+ { 0x36FC, 0x3A93, 0 },
+ { 0x36FE, 0xB551, 0 },
+ { 0x3700, 0xE214, 0 },
+ { 0x3702, 0xF2B0, 0 },
+ { 0x3704, 0x8C30, 0 },
+ { 0x3706, 0x3053, 0 },
+ { 0x3708, 0x64F0, 0 },
+ { 0x370A, 0xFC73, 0 },
+ { 0x370C, 0xD311, 0 },
+ { 0x370E, 0x336F, 0 },
+ { 0x3710, 0x5AF3, 0 },
+ { 0x3712, 0x4EAF, 0 },
+ { 0x3714, 0xDBD4, 0 },
+
+ /* Lens shading origin */
+ { 0x3644, 0x02A0, 0 },
+ { 0x3642, 0x01FC, 0 },
+ { 0x3210, 0x01B8, 0 },
+
+ /* Color correction matrix - Low light */
+ { 0x098C, 0x2306, 0 },
+ { 0x0990, 0x0233, 0 },
+ { 0x098C, 0x2308, 0 },
+ { 0x0990, 0xFF0B, 0 },
+ { 0x098C, 0x230A, 0 },
+ { 0x0990, 0x0024, 0 },
+ { 0x098C, 0x230C, 0 },
+ { 0x0990, 0xFFC8, 0 },
+ { 0x098C, 0x230E, 0 },
+ { 0x0990, 0x01DE, 0 },
+ { 0x098C, 0x2310, 0 },
+ { 0x0990, 0xFFBD, 0 },
+ { 0x098C, 0x2312, 0 },
+ { 0x0990, 0x0019, 0 },
+ { 0x098C, 0x2314, 0 },
+ { 0x0990, 0xFF2B, 0 },
+ { 0x098C, 0x2316, 0 },
+ { 0x0990, 0x01E8, 0 },
+ { 0x098C, 0x2318, 0 },
+ { 0x0990, 0x0024, 0 },
+ { 0x098C, 0x231A, 0 },
+ { 0x0990, 0x0030, 0 },
+
+ /* Color correction matrix - RL (delta) */
+ { 0x098C, 0x231C, 0 },
+ { 0x0990, 0xFF7D, 0 },
+ { 0x098C, 0x231E, 0 },
+ { 0x0990, 0x002C, 0 },
+ { 0x098C, 0x2320, 0 },
+ { 0x0990, 0x002C, 0 },
+ { 0x098C, 0x2322, 0 },
+ { 0x0990, 0x0006, 0 },
+ { 0x098C, 0x2324, 0 },
+ { 0x0990, 0x00A3, 0 },
+ { 0x098C, 0x2326, 0 },
+ { 0x0990, 0xFF75, 0 },
+ { 0x098C, 0x2328, 0 },
+ { 0x0990, 0xFFF4, 0 },
+ { 0x098C, 0x232A, 0 },
+ { 0x0990, 0x00AC, 0 },
+ { 0x098C, 0x232C, 0 },
+ { 0x0990, 0xFF75, 0 },
+ { 0x098C, 0x232E, 0 },
+ { 0x0990, 0x0010, 0 },
+ { 0x098C, 0x2330, 0 },
+ { 0x0990, 0xFFF4, 0 },
+
+ /* AWB settings */
+ { 0x098C, 0xA348, 0 },
+ { 0x0990, 0x0008, 0 },
+ { 0x098C, 0xA349, 0 },
+ { 0x0990, 0x0002, 0 },
+ { 0x098C, 0xA34A, 0 },
+ { 0x0990, 0x0059, 0 },
+ { 0x098C, 0xA34B, 0 },
+ { 0x0990, 0x00A6, 0 },
+ { 0x098C, 0xA351, 0 },
+ { 0x0990, 0x0000, 0 },
+ { 0x098C, 0xA352, 0 },
+ { 0x0990, 0x007F, 0 },
+ { 0x098C, 0xA35D, 0 },
+ { 0x0990, 0x0078, 0 },
+ { 0x098C, 0xA35E, 0 },
+ { 0x0990, 0x0086, 0 },
+ { 0x098C, 0xA35F, 0 },
+ { 0x0990, 0x007E, 0 },
+ { 0x098C, 0xA360, 0 },
+ { 0x0990, 0x0082, 0 },
+
+ /* Cold color adjustment */
+ { 0x098C, 0xA369, 0 },
+ { 0x0990, 0x0097, 0 },
+ { 0x098C, 0xA36A, 0 },
+ { 0x0990, 0x008C, 0 },
+ { 0x098C, 0xA36B, 0 },
+ { 0x0990, 0x0080, 0 },
+
+ /* AWB window */
+ { 0x098C, 0xA302, 0 },
+ { 0x0990, 0x0000, 0 },
+ { 0x098C, 0xA303, 0 },
+ { 0x0990, 0x00FF, 0 },
+
+ /* AE preview settings */
+ { 0x098C, 0xA11D, 0 },
+ { 0x0990, 0x0002, 0 },
+ { 0x098C, 0x271F, 0 },
+ { 0x0990, 0x032E, 0 },
+ { 0x098C, 0x2721, 0 },
+ { 0x0990, 0x04CC, 0 },
+
+ /* AE gain settings */
+ { 0x098C, 0xA216, 0 },
+ { 0x0990, 0x0060, 0 },
+ { 0x098C, 0xA215, 0 },
+ { 0x0990, 0x000A, 0 },
+ { 0x098C, 0xA20C, 0 },
+ { 0x0990, 0x0028, 0 },
+ { 0x098C, 0xA24F, 0 },
+ { 0x0990, 0x0042, 0 },
+ { 0x098C, 0xA20E, 0 },
+ { 0x0990, 0x0060, 0 },
+
+ /* AE window */
+ { 0x098C, 0xA202, 0 },
+ { 0x0990, 0x0000, 0 },
+ { 0x098C, 0xA203, 0 },
+ { 0x0990, 0x00FF, 0 },
+ { 0x098C, 0xA207, 0 },
+ { 0x0990, 0x0004, 0 },
+
+ /* Gamma morph control */
+ { 0x098C, 0xAB37, 0 },
+ { 0x0990, 0x0003, 0 },
+ { 0x098C, 0x2B38, 0 },
+ { 0x0990, 0x3A98, 0 },
+ { 0x098C, 0x2B3A, 0 },
+ { 0x0990, 0x5000, 0 },
+
+ /* Saturation */
+ { 0x098C, 0xAB20, 0 },
+ { 0x0990, 0x0023, 0 },
+ { 0x098C, 0xAB24, 0 },
+ { 0x0990, 0x0010, 0 },
+
+ /* AE speed */
+ { 0x098C, 0xA109, 0 },
+ { 0x0990, 0x0020, 0 },
+ { 0x098C, 0xA10A, 0 },
+ { 0x0990, 0x0002, 0 },
+
+ /* Gamma table A */
+ { 0x098C, 0xAB3C, 0 },
+ { 0x0990, 0x0000, 0 },
+ { 0x098C, 0xAB3D, 0 },
+ { 0x0990, 0x0006, 0 },
+ { 0x098C, 0xAB3E, 0 },
+ { 0x0990, 0x0014, 0 },
+ { 0x098C, 0xAB3F, 0 },
+ { 0x0990, 0x0038, 0 },
+ { 0x098C, 0xAB40, 0 },
+ { 0x0990, 0x005F, 0 },
+ { 0x098C, 0xAB41, 0 },
+ { 0x0990, 0x0079, 0 },
+ { 0x098C, 0xAB42, 0 },
+ { 0x0990, 0x008D, 0 },
+ { 0x098C, 0xAB43, 0 },
+ { 0x0990, 0x009E, 0 },
+ { 0x098C, 0xAB44, 0 },
+ { 0x0990, 0x00AC, 0 },
+ { 0x098C, 0xAB45, 0 },
+ { 0x0990, 0x00B8, 0 },
+ { 0x098C, 0xAB46, 0 },
+ { 0x0990, 0x00C3, 0 },
+ { 0x098C, 0xAB47, 0 },
+ { 0x0990, 0x00CD, 0 },
+ { 0x098C, 0xAB48, 0 },
+ { 0x0990, 0x00D5, 0 },
+ { 0x098C, 0xAB49, 0 },
+ { 0x0990, 0x00DE, 0 },
+ { 0x098C, 0xAB4A, 0 },
+ { 0x0990, 0x00E5, 0 },
+ { 0x098C, 0xAB4B, 0 },
+ { 0x0990, 0x00EC, 0 },
+ { 0x098C, 0xAB4C, 0 },
+ { 0x0990, 0x00F3, 0 },
+ { 0x098C, 0xAB4D, 0 },
+ { 0x0990, 0x00F9, 0 },
+ { 0x098C, 0xAB4E, 0 },
+ { 0x0990, 0x00FF, 0 },
+
+ /* Noise reduction RGB */
+ { 0x098C, 0xAB2C, 0 },
+ { 0x0990, 0x0010, 0 },
+ { 0x098C, 0xAB2D, 0 },
+ { 0x0990, 0x002A, 0 },
+ { 0x098C, 0xAB2E, 0 },
+ { 0x0990, 0x0010, 0 },
+ { 0x098C, 0xAB2F, 0 },
+ { 0x0990, 0x0010, 0 },
+
+ /* Gamma table B */
+ { 0x098C, 0xAB4F, 0 },
+ { 0x0990, 0x0000, 0 },
+ { 0x098C, 0xAB50, 0 },
+ { 0x0990, 0x0004, 0 },
+ { 0x098C, 0xAB51, 0 },
+ { 0x0990, 0x000D, 0 },
+ { 0x098C, 0xAB52, 0 },
+ { 0x0990, 0x0028, 0 },
+ { 0x098C, 0xAB53, 0 },
+ { 0x0990, 0x0053, 0 },
+ { 0x098C, 0xAB54, 0 },
+ { 0x0990, 0x0075, 0 },
+ { 0x098C, 0xAB55, 0 },
+ { 0x0990, 0x0092, 0 },
+ { 0x098C, 0xAB56, 0 },
+ { 0x0990, 0x00A7, 0 },
+ { 0x098C, 0xAB57, 0 },
+ { 0x0990, 0x00B7, 0 },
+ { 0x098C, 0xAB58, 0 },
+ { 0x0990, 0x00C4, 0 },
+ { 0x098C, 0xAB59, 0 },
+ { 0x0990, 0x00CF, 0 },
+ { 0x098C, 0xAB5A, 0 },
+ { 0x0990, 0x00D8, 0 },
+ { 0x098C, 0xAB5B, 0 },
+ { 0x0990, 0x00DF, 0 },
+ { 0x098C, 0xAB5C, 0 },
+ { 0x0990, 0x00E6, 0 },
+ { 0x098C, 0xAB5D, 0 },
+ { 0x0990, 0x00EC, 0 },
+ { 0x098C, 0xAB5E, 0 },
+ { 0x0990, 0x00F2, 0 },
+ { 0x098C, 0xAB5F, 0 },
+ { 0x0990, 0x00F6, 0 },
+ { 0x098C, 0xAB60, 0 },
+ { 0x0990, 0x00FB, 0 },
+ { 0x098C, 0xAB61, 0 },
+ { 0x0990, 0x00FF, 0 },
+
+ /* Read mode - no mirror/flip */
+ { 0x098C, 0x2717, 0 },
+ { 0x0990, 0x046C, 0 },
+ { 0x098C, 0x272D, 0 },
+ { 0x0990, 0x0024, 0 },
+
+ /* Reset command before sequencer */
+ { 0x001A, 0x021C, 0 },
+
+ /* Issue refresh command */
+ { 0x098C, 0xA103, 0 },
+ { 0x0990, 0x0006, 0 },
+};
+
+/* Apply the MT9M113 initialization table */
+static int mt9m113_sensor_init(struct mt9m113 *sensor)
+{
+ struct device *dev = &sensor->client->dev;
+ int ret = 0;
+ unsigned int i;
+
+ /* MCU is about to be fully re-initialised, so any prior test-pattern
+ * override is gone. Clear the bookkeeping so a subsequent
+ * V4L2_CID_TEST_PATTERN=0 does not re-run the disable sequence;
+ * also drop the cached pattern value so stream_on() doesn't
+ * replay the apply after a runtime suspend/resume cycle that
+ * already reset MCU state.
+ */
+ sensor->test_pattern_active = false;
+ sensor->test_pattern_value = 0;
+
+ dev_dbg(dev, "MT9M113: applying init table (%zu entries)\n",
+ ARRAY_SIZE(mt9m113_init_table));
+
+ /*
+ * Suspend double buffer updates so all init table writes take effect
+ * atomically at frame start. Per datasheet, R0x0248[15] inhibits
+ * transfers from pending to live registers.
+ */
+ ret = mt9m113_double_buffer_suspend(sensor);
+ if (ret) {
+ dev_warn(dev, "Failed to suspend double buffer: %d\n", ret);
+ /* Continue anyway - not fatal */
+ }
+
+ for (i = 0; i < ARRAY_SIZE(mt9m113_init_table); i++) {
+ const struct mt9m113_reg_entry *entry = &mt9m113_init_table[i];
+
+ ret = cci_write(sensor->regmap, CCI_REG16(entry->reg),
+ entry->value, NULL);
+ if (ret < 0) {
+ dev_err(dev, "MT9M113: reg 0x%04x write failed: %d\n",
+ entry->reg, ret);
+ mt9m113_double_buffer_resume(sensor);
+ return ret;
+ }
+
+ if (entry->delay_ms > 0)
+ msleep(entry->delay_ms);
+ }
+
+ /* Resume double buffer updates - changes take effect at next frame start */
+ ret = mt9m113_double_buffer_resume(sensor);
+ if (ret) {
+ dev_warn(dev, "Failed to resume double buffer: %d\n", ret);
+ /* Continue anyway - not fatal */
+ }
+
+ /* Wait for MCU to complete refresh */
+ ret = mt9m113_poll_mcu_var(sensor, MT9M113_SEQ_CMD, 0x0000, 1000);
+ if (ret < 0) {
+ dev_err(dev, "MT9M113: MCU refresh timeout\n");
+ return ret;
+ }
+
+ /* Issue sequencer refresh */
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_SEQ_CMD,
+ MT9M113_SEQ_CMD_REFRESH);
+ if (ret < 0)
+ return ret;
+
+ ret = mt9m113_poll_mcu_var(sensor, MT9M113_SEQ_CMD, 0x0000, 1000);
+ if (ret < 0) {
+ dev_err(dev, "MT9M113: SEQ refresh timeout\n");
+ return ret;
+ }
+
+ /*
+ * Enable MIPI Frame-Start/End short packets. Without them the VFE CAMIF
+ * has no per-frame boundary marker and runs in line-counting (APS) mode,
+ * which slips against the sensor's free-running readout and makes the
+ * captured image walk vertically (~tens of lines/frame, resolution
+ * dependent). Emitting the frame-sync short packets locks every frame.
+ */
+ ret = cci_write(sensor->regmap, MT9M113_CUSTOM_SHORT_PKT,
+ MT9M113_CUSTOM_SHORT_PKT_FRAME_CNT_EN, NULL);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Do NOT enable MIPI output here. It is enabled in start_streaming once
+ * the output config is programmed, followed by REFRESH_MODE + REFRESH.
+ * Enabling MIPI before the CSIPHY is configured causes problems.
+ */
+
+ dev_dbg(dev, "MT9M113: init complete\n");
+ return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * Streaming
+ */
+
+/*
+ * Configure AE (Auto Exposure) parameters for preview vs snapshot/video mode.
+ * From legacy vendor driver: snapshot mode allows longer exposure for better quality,
+ * while preview mode optimizes for higher frame rate and lower power.
+ */
+static int mt9m113_configure_ae_mode(struct mt9m113 *sensor, bool snapshot_mode)
+{
+ struct device *dev = &sensor->client->dev;
+ int ret;
+
+ if (snapshot_mode) {
+ /* Snapshot/Capture mode: allow longer exposure for quality */
+ dev_dbg(dev, "MT9M113: configuring AE for snapshot mode\n");
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_MAX_INDEX, 0x0028);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_MAX_VIRTGAIN, 0x0060);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_MAX_DGAIN_AE1, 0x00C8);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_JUMP_DIVISOR, 0x0002);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_SKIP_FRAMES, 0x0002);
+ if (ret)
+ return ret;
+ } else {
+ /* Preview mode: optimize for frame rate and responsiveness */
+ dev_dbg(dev, "MT9M113: configuring AE for preview mode\n");
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_MAX_INDEX, 0x0008);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_MAX_VIRTGAIN, 0x00A0);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_MAX_DGAIN_AE1, 0x0150);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_JUMP_DIVISOR, 0x0001);
+ if (ret)
+ return ret;
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_SKIP_FRAMES, 0x0001);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+/*
+ * Program the per-context output dimensions and pixel format, then re-apply the
+ * sensor readout geometry. Output configuration is double-buffered so it
+ * latches atomically at the next frame start.
+ */
+static int mt9m113_configure_output(struct mt9m113 *sensor, bool use_context_b,
+ u32 code)
+{
+ struct device *dev = &sensor->client->dev;
+ u16 width_reg, height_reg, format_reg;
+ u16 width_val, height_val, format_val;
+ int ret;
+
+ if (use_context_b) {
+ width_reg = MT9M113_MODE_OUTPUT_WIDTH_B;
+ height_reg = MT9M113_MODE_OUTPUT_HEIGHT_B;
+ format_reg = MT9M113_MODE_OUTPUT_FORMAT_B;
+ width_val = 1280;
+ height_val = 1024;
+ } else {
+ width_reg = MT9M113_MODE_OUTPUT_WIDTH_A;
+ height_reg = MT9M113_MODE_OUTPUT_HEIGHT_A;
+ format_reg = MT9M113_MODE_OUTPUT_FORMAT_A;
+ width_val = 640;
+ height_val = 480;
+ }
+
+ format_val = mt9m113_format_val(code);
+
+ ret = mt9m113_double_buffer_suspend(sensor);
+ if (ret)
+ dev_warn(dev, "Failed to suspend double buffer: %d\n", ret);
+
+ ret = mt9m113_write_mcu_var(sensor, width_reg, width_val);
+ if (!ret)
+ ret = mt9m113_write_mcu_var(sensor, height_reg, height_val);
+ if (!ret)
+ ret = mt9m113_write_mcu_var(sensor, format_reg, format_val);
+
+ {
+ int resume_ret = mt9m113_double_buffer_resume(sensor);
+
+ if (!ret)
+ ret = resume_ret;
+ }
+ if (ret)
+ return ret;
+
+ dev_dbg(dev, "MT9M113: Context %c: %ux%u, format=0x%04x\n",
+ use_context_b ? 'B' : 'A', width_val, height_val, format_val);
+
+ /*
+ * Re-apply the sensor readout geometry. The MCU variables for
+ * row_end/read_mode can be left stale after switching from Context B to
+ * Context A, producing wrong line counts and a corrupted image.
+ */
+ ret = mt9m113_configure_sensor_context(sensor, use_context_b);
+ if (ret)
+ dev_err(dev, "Failed to configure sensor context: %d\n", ret);
+
+ return ret;
+}
+
+/*
+ * The MCU resets OUTPUT_CONTROL and MODE_OUTPUT_FORMAT to their defaults during
+ * sequencer state transitions, so re-apply them once the stream is running.
+ * Best-effort: a failure is logged but does not abort the stream.
+ */
+static void mt9m113_reassert_output(struct mt9m113 *sensor, u16 output_ctrl_val,
+ u16 format_reg, u32 code)
+{
+ struct device *dev = &sensor->client->dev;
+ u16 format_val = mt9m113_format_val(code);
+
+ if (cci_write(sensor->regmap, MT9M113_OUTPUT_CONTROL, output_ctrl_val,
+ NULL))
+ dev_warn(dev, "MT9M113: OUTPUT_CONTROL re-write failed\n");
+ if (mt9m113_write_mcu_var(sensor, format_reg, format_val))
+ dev_warn(dev, "MT9M113: MODE_OUTPUT_FORMAT re-write failed\n");
+}
+
+/* Context A (640x480 preview): enable output and run the preview sequencer. */
+static int mt9m113_stream_context_a(struct mt9m113 *sensor, u16 output_ctrl_val,
+ u32 code)
+{
+ struct device *dev = &sensor->client->dev;
+ int ret;
+
+ ret = cci_write(sensor->regmap, MT9M113_OUTPUT_CONTROL, output_ctrl_val,
+ NULL);
+ if (ret)
+ return ret;
+ dev_dbg(dev, "MT9M113: OUTPUT_CONTROL=0x%04x enabled\n", output_ctrl_val);
+
+ ret = cci_write(sensor->regmap, MT9M113_RESET_REGISTER,
+ MT9M113_RESET_REG_STREAMING, NULL);
+ if (ret)
+ return ret;
+
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_SEQ_CAP_MODE,
+ MT9M113_SEQ_CAP_MODE_PREVIEW);
+ if (ret)
+ return ret;
+ msleep(40);
+
+ dev_dbg(dev, "MT9M113: Writing SEQ_CMD_RUN\n");
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_SEQ_CMD, MT9M113_SEQ_CMD_RUN);
+ if (ret)
+ return ret;
+
+ ret = mt9m113_poll_mcu_var(sensor, MT9M113_SEQ_CMD, 0x0000, 500);
+ if (ret < 0)
+ dev_warn(dev, "MT9M113: SEQ_CMD_RUN did not complete\n");
+
+ mt9m113_reassert_output(sensor, output_ctrl_val,
+ MT9M113_MODE_OUTPUT_FORMAT_A, code);
+ msleep(20);
+ return 0;
+}
+
+/*
+ * Context B (1280x1024 capture): the MCU only accepts CAPTURE from stable
+ * preview, so enter preview first, wait for SEQ_STATE=PREVIEW, then switch.
+ */
+static int mt9m113_stream_context_b(struct mt9m113 *sensor, u16 output_ctrl_val,
+ u32 code)
+{
+ struct device *dev = &sensor->client->dev;
+ u64 seq_state = 0;
+ unsigned int i;
+ int ret;
+
+ ret = cci_write(sensor->regmap, MT9M113_OUTPUT_CONTROL, output_ctrl_val,
+ NULL);
+ if (ret)
+ return ret;
+ dev_dbg(dev, "MT9M113: OUTPUT_CONTROL=0x%04x enabled\n", output_ctrl_val);
+
+ ret = cci_write(sensor->regmap, MT9M113_RESET_REGISTER,
+ MT9M113_RESET_REG_STREAMING, NULL);
+ if (ret)
+ return ret;
+
+ /* Enter preview first. */
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_SEQ_CAP_MODE,
+ MT9M113_SEQ_CAP_MODE_PREVIEW);
+ if (ret)
+ return ret;
+ msleep(40);
+
+ dev_dbg(dev, "MT9M113: Entering preview mode first (SEQ_CMD_RUN)\n");
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_SEQ_CMD, MT9M113_SEQ_CMD_RUN);
+ if (ret)
+ return ret;
+
+ ret = mt9m113_poll_mcu_var(sensor, MT9M113_SEQ_CMD, 0x0000, 500);
+ if (ret < 0)
+ dev_warn(dev, "MT9M113: SEQ_CMD_RUN did not complete\n");
+
+ for (i = 0; i < 100; i++) {
+ mt9m113_read_mcu_var(sensor, MT9M113_SEQ_STATE, &seq_state);
+ if (seq_state == MT9M113_SEQ_STATE_PREVIEW)
+ break;
+ usleep_range(10000, 11000);
+ }
+ if (seq_state != MT9M113_SEQ_STATE_PREVIEW)
+ dev_warn(dev,
+ "MT9M113: preview state not reached (SEQ_STATE=0x%llx)\n",
+ seq_state);
+
+ /* Switch to video mode (stays in Context B). */
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_SEQ_CAP_MODE,
+ MT9M113_SEQ_CAP_MODE_VIDEO);
+ if (ret)
+ return ret;
+ msleep(40);
+
+ ret = mt9m113_seq_cmd_ready(sensor);
+ if (ret < 0) {
+ dev_err(dev, "MT9M113: MCU not ready for CAPTURE command\n");
+ return ret;
+ }
+
+ dev_dbg(dev, "MT9M113: switching to Context B (SEQ_CMD_CAPTURE)\n");
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_SEQ_CMD,
+ MT9M113_SEQ_CMD_CAPTURE);
+ if (ret)
+ return ret;
+
+ ret = mt9m113_poll_mcu_var(sensor, MT9M113_SEQ_CMD, 0x0000, 500);
+ if (ret < 0)
+ dev_warn(dev, "MT9M113: SEQ_CMD_CAPTURE did not complete\n");
+
+ for (i = 0; i < 100; i++) {
+ mt9m113_read_mcu_var(sensor, MT9M113_SEQ_STATE, &seq_state);
+ if (seq_state == MT9M113_SEQ_STATE_CAPTURE)
+ break;
+ usleep_range(10000, 11000);
+ }
+ if (seq_state != MT9M113_SEQ_STATE_CAPTURE) {
+ dev_err(dev, "MT9M113: Context B switch failed (SEQ_STATE=0x%llx)\n",
+ seq_state);
+ return -ETIMEDOUT;
+ }
+ dev_dbg(dev, "MT9M113: reached capture state\n");
+
+ mt9m113_reassert_output(sensor, output_ctrl_val,
+ MT9M113_MODE_OUTPUT_FORMAT_B, code);
+
+ /* The sensor pipeline needs time to reconfigure for 1280x1024. */
+ msleep(200);
+ return 0;
+}
+
+/*
+ * Apply the MCU-side test-pattern config and freeze the MCU in boot mode
+ * so the normal sequencer cannot overwrite it. Per the MT9M113 datasheet
+ * R0x0066 (mode_common_mode_settings_test_mode) "Test Pattern Generator.
+ * Changes take effect only after REFRESH command", and "Disabling the MCU
+ * is recommended before enabling test patterns."
+ *
+ * The pattern index is written verbatim to the Driver-7 R0x0066 register
+ * (encoded as MT9M113_MODE_TEST_MODE = 0x2766) - menu items already match
+ * the datasheet's value table 1..5. NOTE: do NOT switch CAM_MODE_SELECT
+ * into a "test pattern" state - that puts the camera-mode driver into a
+ * mode where the sequencer no longer processes SEQ_CMD, and the REFRESH
+ * below hangs.
+ *
+ * Called from two places:
+ *
+ * 1. mt9m113_s_ctrl(V4L2_CID_TEST_PATTERN > 0) while streaming - apply
+ * immediately.
+ *
+ * 2. mt9m113_stream_on(), after stream_context_{a,b}() has brought the
+ * pipeline up - re-apply when the test pattern was selected before
+ * streaming started. __v4l2_ctrl_handler_setup() in stream_on runs
+ * with sensor->streaming still false, so the in-handler halt is
+ * skipped; replaying here makes the "set test pattern, then STREAMON"
+ * sequence work.
+ *
+ * Caller must hold the same context as mt9m113_s_ctrl() (an active PM
+ * reference); we touch MCU vars + BOOT_MODE.
+ */
+static int mt9m113_apply_test_pattern(struct mt9m113 *sensor, u8 pattern_idx)
+{
+ int ret;
+
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_MODE_TEST_MODE, pattern_idx);
+ if (ret)
+ return ret;
+ ret = mt9m113_refresh(sensor);
+ if (ret)
+ return ret;
+
+ dev_dbg(&sensor->client->dev,
+ "MT9M113: Halting MCU to lock test pattern %u\n", pattern_idx);
+ cci_write(sensor->regmap, MT9M113_MCU_BOOT_MODE, 0x0001, &ret);
+ return ret;
+}
+
+static int mt9m113_stream_on(struct mt9m113 *sensor,
+ struct v4l2_subdev_state *state)
+{
+ struct device *dev = &sensor->client->dev;
+ const struct v4l2_mbus_framefmt *format;
+ const struct v4l2_rect *compose;
+ u64 health_check, seq_cmd;
+ bool use_context_b;
+ u16 output_ctrl_val;
+ int ret;
+
+ /*
+ * Wake the MCU out of standby and give it time to settle (50ms matches
+ * the legacy vendor driver).
+ */
+ dev_dbg(dev, "MT9M113: start_streaming\n");
+ cci_write(sensor->regmap, MT9M113_STANDBY_CONTROL,
+ MT9M113_STANDBY_CONTROL_ACTIVE, NULL);
+ msleep(50);
+
+ /*
+ * MCU health check: MODE_OUTPUT_WIDTH_A reads back non-zero once the
+ * MCU is running. If it is unresponsive, re-apply the init table.
+ */
+ ret = mt9m113_read_mcu_var(sensor, MT9M113_MODE_OUTPUT_WIDTH_A,
+ &health_check);
+ if (ret < 0 || health_check == 0) {
+ dev_warn(dev, "MT9M113: MCU unresponsive, re-init\n");
+ ret = mt9m113_sensor_init(sensor);
+ if (ret < 0)
+ return ret;
+ }
+
+ /*
+ * Clear stale SEQ_CMD. The init table ends with REFRESH (SEQ_CMD=0x05)
+ * which may not complete before the sensor enters standby/suspend. On
+ * resume, SEQ_CMD is stuck at 0x05 and all subsequent commands fail.
+ * Force-clear it.
+ */
+ ret = mt9m113_read_mcu_var(sensor, MT9M113_SEQ_CMD, &seq_cmd);
+ if (ret == 0 && seq_cmd != 0) {
+ dev_warn(dev, "MT9M113: Clearing stale SEQ_CMD=0x%llx\n", seq_cmd);
+ mt9m113_write_mcu_var(sensor, MT9M113_SEQ_CMD, 0x0000);
+ msleep(50);
+ }
+
+ /*
+ * Re-assert the MIPI Frame-Start/End short packets on every stream
+ * start. The MCU clears CUSTOM_SHORT_PKT across standby/refresh
+ * cycles, and mt9m113_sensor_init() (which also sets it) only runs on
+ * the MCU-recovery path - so without this the bit is lost after the
+ * first stream. Without the per-frame boundary marker the VFE CAMIF
+ * falls back to line-counting and the image walks vertically.
+ */
+ ret = cci_write(sensor->regmap, MT9M113_CUSTOM_SHORT_PKT,
+ MT9M113_CUSTOM_SHORT_PKT_FRAME_CNT_EN, NULL);
+ if (ret < 0)
+ return ret;
+
+ /* Apply all V4L2 controls (color effects, etc.) before streaming */
+ ret = __v4l2_ctrl_handler_setup(&sensor->ifp.hdl);
+ if (ret) {
+ dev_err(dev, "Failed to setup controls: %d\n", ret);
+ return ret;
+ }
+
+ compose = v4l2_subdev_state_get_compose(state, 0);
+ /* Source pad (pad 1) carries the MIPI output format. */
+ format = v4l2_subdev_state_get_format(state, 1);
+
+ use_context_b = (compose->width > 640 || compose->height > 480);
+ dev_dbg(dev, "MT9M113: %ux%u -> Context %c\n",
+ compose->width, compose->height, use_context_b ? 'B' : 'A');
+
+ /*
+ * Configure AE for the selected context: Context B (capture) allows a
+ * longer exposure for quality, Context A (preview) optimises for frame
+ * rate.
+ */
+ ret = mt9m113_configure_ae_mode(sensor, use_context_b);
+ if (ret) {
+ dev_err(dev, "Failed to configure AE mode: %d\n", ret);
+ return ret;
+ }
+
+ ret = mt9m113_configure_output(sensor, use_context_b, format->code);
+ if (ret)
+ return ret;
+
+ /* Wait for CSIPHY stabilization */
+ msleep(MT9M113_PRE_MIPI_DELAY_MS);
+
+ /*
+ * YUV/RGB output: enable MIPI CSI-2 in FIFO-bypass mode and restore the
+ * default ISP colour pipeline.
+ */
+ output_ctrl_val = MT9M113_OUTPUT_CONTROL_MIPI_ENABLE;
+ ret = cci_write(sensor->regmap, MT9M113_OFIFO_CONTROL_STATUS,
+ MT9M113_OFIFO_BYPASS, NULL);
+ if (ret)
+ return ret;
+ ret = cci_write(sensor->regmap, MT9M113_COLOR_PIPELINE_CONTROL,
+ MT9M113_COLOR_PIPELINE_DEFAULT, NULL);
+ if (ret)
+ return ret;
+
+ /* The MCU must be idle before it will accept a sequencer command. */
+ ret = mt9m113_seq_cmd_ready(sensor);
+ if (ret < 0) {
+ dev_err(dev, "MT9M113: MCU not ready for streaming command\n");
+ return ret;
+ }
+
+ /*
+ * One REFRESH applies the per-session output dimensions/format; without
+ * it SEQ_CMD_RUN hangs (the MCU never clears SEQ_CMD). OFIFO and the
+ * colour pipeline are already programmed above - they must not be
+ * written while a REFRESH is pending or it times out.
+ */
+ ret = mt9m113_refresh(sensor);
+ if (ret)
+ dev_warn(dev, "MT9M113: REFRESH failed, continuing\n");
+
+ /*
+ * For Context B the MCU must reach stable preview (SEQ_STATE=0x04)
+ * before it will accept the CAPTURE command, so enter preview first and
+ * then switch. Context A simply runs preview.
+ */
+ if (use_context_b)
+ ret = mt9m113_stream_context_b(sensor, output_ctrl_val,
+ format->code);
+ else
+ ret = mt9m113_stream_context_a(sensor, output_ctrl_val,
+ format->code);
+ if (ret)
+ return ret;
+
+ /*
+ * If V4L2_CID_TEST_PATTERN was set to a non-zero value before the
+ * stream started, mt9m113_s_ctrl() noted it on test_pattern_{active,
+ * value} but couldn't commit the MCU writes (the normal stream init
+ * below would have overwritten MODE_SELECT). Replay the apply now
+ * that the pipeline is up so STREAMON ends with the test pattern
+ * visible. Read the cached value directly - do NOT call
+ * v4l2_ctrl_find() here, the ctrl-handler mutex is already held by
+ * the V4L2 core for the duration of this s_stream callback, so a
+ * lookup would self-deadlock.
+ */
+ if (sensor->test_pattern_active && sensor->test_pattern_value > 0) {
+ ret = mt9m113_apply_test_pattern(sensor,
+ sensor->test_pattern_value);
+ if (ret)
+ return ret;
+ }
+
+ dev_dbg(dev, "MT9M113: streaming started\n");
+ return 0;
+}
+
+/*
+ * The MT9M113 MCU intermittently wedges on stream start; the failures cluster
+ * at the start of a run and then clear. Retry a bounded number of times, fully
+ * power-cycling the sensor (runtime-PM suspend -> resume = power_off + power_on
+ * + sensor_init) between attempts. Exactly one pm_runtime get/put pair runs per
+ * attempt; on success the reference is held for the streaming session and
+ * released by mt9m113_stop_streaming().
+ */
+static int mt9m113_start_streaming(struct mt9m113 *sensor,
+ struct v4l2_subdev_state *state)
+{
+ struct device *dev = &sensor->client->dev;
+ unsigned int attempt;
+ int ret = 0;
+
+ /*
+ * Guard against a redundant s_stream(1): a second
+ * pm_runtime_resume_and_get() here would leak a PM reference and pin
+ * the device awake forever, because mt9m113_stop_streaming() only
+ * drops one reference per stop.
+ */
+ if (sensor->streaming)
+ return 0;
+
+ for (attempt = 0; attempt < MT9M113_STREAM_START_RETRIES; attempt++) {
+ ret = pm_runtime_resume_and_get(dev);
+ if (ret)
+ return ret;
+
+ ret = mt9m113_stream_on(sensor, state);
+ if (!ret) {
+ sensor->streaming = true;
+ return 0;
+ }
+
+ pm_runtime_put_sync_suspend(dev);
+ if (attempt + 1 < MT9M113_STREAM_START_RETRIES)
+ dev_warn(dev,
+ "MT9M113: stream start failed (%d), power-cycle + retry %u/%u\n",
+ ret, attempt + 1, MT9M113_STREAM_START_RETRIES - 1);
+ }
+
+ return ret;
+}
+
+static int mt9m113_stop_streaming(struct mt9m113 *sensor)
+{
+ struct device *dev = &sensor->client->dev;
+ int ret;
+
+ if (!sensor->streaming)
+ return 0;
+
+ sensor->streaming = false;
+
+ /* Disable MIPI output */
+ ret = cci_write(sensor->regmap, MT9M113_OUTPUT_CONTROL, 0x0000, NULL);
+ if (ret < 0)
+ dev_warn(dev,
+ "MT9M113: MIPI output disable failed (%d), receiver may still see traffic\n",
+ ret);
+
+ /*
+ * Wait briefly for any pending SEQ_CMD to complete.
+ * Don't issue REFRESH here - it can leave MCU stuck if it times out.
+ * Start_streaming will handle full re-initialization.
+ */
+ ret = mt9m113_poll_mcu_var(sensor, MT9M113_SEQ_CMD, 0x0000, 100);
+ if (ret < 0)
+ dev_dbg(dev, "MT9M113: SEQ_CMD did not complete before stop\n");
+
+ dev_dbg(dev, "MT9M113: streaming stopped\n");
+
+ pm_runtime_put_autosuspend(dev);
+ return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * V4L2 Subdev Operations
+ */
+
+static inline struct mt9m113 *ifp_to_mt9m113(struct v4l2_subdev *sd)
+{
+ return container_of(sd, struct mt9m113, ifp.sd);
+}
+
+static int mt9m113_ifp_s_stream(struct v4l2_subdev *sd, int enable)
+{
+ struct mt9m113 *sensor = ifp_to_mt9m113(sd);
+ struct v4l2_subdev_state *state;
+ int ret;
+
+ state = v4l2_subdev_lock_and_get_active_state(sd);
+
+ if (enable)
+ ret = mt9m113_start_streaming(sensor, state);
+ else
+ ret = mt9m113_stop_streaming(sensor);
+
+ v4l2_subdev_unlock_state(state);
+ return ret;
+}
+
+/* -----------------------------------------------------------------------------
+ * Pixel Array Subdev Operations
+ */
+
+static int mt9m113_pa_init_state(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state)
+{
+ struct v4l2_mbus_framefmt *format;
+ struct v4l2_rect *crop;
+
+ crop = v4l2_subdev_state_get_crop(state, 0);
+ crop->left = 0;
+ crop->top = 0;
+ crop->width = MT9M113_PIXEL_ARRAY_WIDTH;
+ crop->height = MT9M113_PIXEL_ARRAY_HEIGHT;
+
+ format = v4l2_subdev_state_get_format(state, 0);
+ format->width = MT9M113_PIXEL_ARRAY_WIDTH;
+ format->height = MT9M113_PIXEL_ARRAY_HEIGHT;
+ format->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+ format->field = V4L2_FIELD_NONE;
+ format->colorspace = V4L2_COLORSPACE_RAW;
+
+ return 0;
+}
+
+static int mt9m113_pa_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ if (code->index > 0)
+ return -EINVAL;
+
+ code->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+ return 0;
+}
+
+static int mt9m113_pa_enum_framesizes(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_frame_size_enum *fse)
+{
+ if (fse->index > 0)
+ return -EINVAL;
+
+ if (fse->code != MEDIA_BUS_FMT_SGRBG10_1X10)
+ return -EINVAL;
+
+ fse->min_width = MT9M113_PIXEL_ARRAY_WIDTH;
+ fse->max_width = MT9M113_PIXEL_ARRAY_WIDTH;
+ fse->min_height = MT9M113_PIXEL_ARRAY_HEIGHT;
+ fse->max_height = MT9M113_PIXEL_ARRAY_HEIGHT;
+
+ return 0;
+}
+
+static int mt9m113_pa_get_selection(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_selection *sel)
+{
+ switch (sel->target) {
+ case V4L2_SEL_TGT_CROP:
+ sel->r = *v4l2_subdev_state_get_crop(state, sel->pad);
+ return 0;
+
+ case V4L2_SEL_TGT_CROP_DEFAULT:
+ case V4L2_SEL_TGT_CROP_BOUNDS:
+ case V4L2_SEL_TGT_NATIVE_SIZE:
+ sel->r.left = 0;
+ sel->r.top = 0;
+ sel->r.width = MT9M113_PIXEL_ARRAY_WIDTH;
+ sel->r.height = MT9M113_PIXEL_ARRAY_HEIGHT;
+ return 0;
+
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct v4l2_subdev_pad_ops mt9m113_pa_pad_ops = {
+ .enum_mbus_code = mt9m113_pa_enum_mbus_code,
+ .enum_frame_size = mt9m113_pa_enum_framesizes,
+ .get_fmt = v4l2_subdev_get_fmt,
+ .get_selection = mt9m113_pa_get_selection,
+};
+
+static const struct v4l2_subdev_ops mt9m113_pa_ops = {
+ .pad = &mt9m113_pa_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops mt9m113_pa_internal_ops = {
+ .init_state = mt9m113_pa_init_state,
+};
+
+/* -----------------------------------------------------------------------------
+ * IFP Subdev Operations
+ */
+
+static int mt9m113_ifp_init_state(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state)
+{
+ struct v4l2_mbus_framefmt *format;
+ struct v4l2_rect *crop;
+ struct v4l2_rect *compose;
+
+ /* Sink pad - receives raw data from PA */
+ format = v4l2_subdev_state_get_format(state, 0);
+ format->width = MT9M113_PIXEL_ARRAY_WIDTH;
+ format->height = MT9M113_PIXEL_ARRAY_HEIGHT;
+ format->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+ format->field = V4L2_FIELD_NONE;
+ format->colorspace = V4L2_COLORSPACE_RAW;
+
+ crop = v4l2_subdev_state_get_crop(state, 0);
+ crop->left = 0;
+ crop->top = 0;
+ crop->width = MT9M113_PIXEL_ARRAY_WIDTH;
+ crop->height = MT9M113_PIXEL_ARRAY_HEIGHT;
+
+ compose = v4l2_subdev_state_get_compose(state, 0);
+ compose->left = 0;
+ compose->top = 0;
+ compose->width = 640;
+ compose->height = 480;
+
+ /* Source pad - outputs processed data to host */
+ format = v4l2_subdev_state_get_format(state, 1);
+ format->width = 640;
+ format->height = 480;
+ format->code = MEDIA_BUS_FMT_UYVY8_1X16;
+ format->field = V4L2_FIELD_NONE;
+ format->colorspace = V4L2_COLORSPACE_SRGB;
+
+ return 0;
+}
+
+static int mt9m113_ifp_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ /* Sink pad only accepts raw from PA */
+ if (code->pad == 0) {
+ if (code->index > 0)
+ return -EINVAL;
+ code->code = MEDIA_BUS_FMT_SGRBG10_1X10;
+ return 0;
+ }
+
+ /* Source pad supports multiple output formats */
+ if (code->index >= ARRAY_SIZE(mt9m113_format_infos))
+ return -EINVAL;
+
+ code->code = mt9m113_format_infos[code->index].code;
+ return 0;
+}
+
+static int mt9m113_ifp_enum_frame_size(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_frame_size_enum *fse)
+{
+ /* Sink pad - fixed raw input size */
+ if (fse->pad == 0) {
+ if (fse->index > 0)
+ return -EINVAL;
+ if (fse->code != MEDIA_BUS_FMT_SGRBG10_1X10)
+ return -EINVAL;
+ fse->min_width = MT9M113_PIXEL_ARRAY_WIDTH;
+ fse->max_width = MT9M113_PIXEL_ARRAY_WIDTH;
+ fse->min_height = MT9M113_PIXEL_ARRAY_HEIGHT;
+ fse->max_height = MT9M113_PIXEL_ARRAY_HEIGHT;
+ return 0;
+ }
+
+ /* Source pad - Context A (640x480) and Context B (1280x1024) */
+ if (fse->index > 1)
+ return -EINVAL;
+ if (mt9m113_format_info(fse->code)->code != fse->code)
+ return -EINVAL;
+
+ if (fse->index == 0) {
+ fse->min_width = 640;
+ fse->max_width = 640;
+ fse->min_height = 480;
+ fse->max_height = 480;
+ } else {
+ fse->min_width = 1280;
+ fse->max_width = 1280;
+ fse->min_height = 1024;
+ fse->max_height = 1024;
+ }
+
+ return 0;
+}
+
+static int mt9m113_ifp_enum_frame_interval(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_frame_interval_enum *fie)
+{
+ /* Only source pad (pad 1) supports frame interval enumeration */
+ if (fie->pad != 1)
+ return -EINVAL;
+
+ /* One interval per resolution */
+ if (fie->index > 0)
+ return -EINVAL;
+
+ /* Context A: 640x480 @ 30fps, Context B: 1280x1024 @ 15fps */
+ if (fie->width == 640 && fie->height == 480) {
+ fie->interval.numerator = 1;
+ fie->interval.denominator = 30;
+ } else if (fie->width == 1280 && fie->height == 1024) {
+ fie->interval.numerator = 1;
+ fie->interval.denominator = 15;
+ } else {
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int mt9m113_ifp_g_frame_interval(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_frame_interval *fi)
+{
+ struct v4l2_mbus_framefmt *format;
+
+ /* Frame intervals are only defined on the source pad. */
+ if (fi->pad != 1)
+ return -EINVAL;
+
+ format = v4l2_subdev_state_get_format(state, 1);
+
+ /* Return interval based on current resolution */
+ if (format->width <= 640 && format->height <= 480) {
+ /* Context A: 30fps */
+ fi->interval.numerator = 1;
+ fi->interval.denominator = 30;
+ } else {
+ /* Context B: 15fps */
+ fi->interval.numerator = 1;
+ fi->interval.denominator = 15;
+ }
+
+ return 0;
+}
+
+static int mt9m113_ifp_set_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_format *fmt)
+{
+ struct mt9m113 *sensor = ifp_to_mt9m113(sd);
+ struct v4l2_mbus_framefmt *format;
+ struct v4l2_rect *compose;
+ const struct mt9m113_format_info *info;
+
+ /*
+ * Reject geometry/format changes while the pipeline is live.
+ * The sensor is only programmed in mt9m113_stream_on(); silently
+ * updating the active state would let userspace see one format while
+ * the wire still carries the previous one.
+ */
+ if (sensor->streaming)
+ return -EBUSY;
+
+ /* Sink pad format is fixed */
+ if (fmt->pad == 0) {
+ format = v4l2_subdev_state_get_format(state, 0);
+ fmt->format = *format;
+ return 0;
+ }
+
+ /* Source pad */
+ info = mt9m113_format_info(fmt->format.code);
+
+ /* Clamp to supported sizes (Context A or Context B) */
+ if (fmt->format.width <= 640) {
+ fmt->format.width = 640;
+ fmt->format.height = 480;
+ } else {
+ fmt->format.width = 1280;
+ fmt->format.height = 1024;
+ }
+
+ format = v4l2_subdev_state_get_format(state, 1);
+ format->width = fmt->format.width;
+ format->height = fmt->format.height;
+ format->code = info->code;
+ format->field = V4L2_FIELD_NONE;
+ format->colorspace = V4L2_COLORSPACE_SRGB;
+
+ compose = v4l2_subdev_state_get_compose(state, 0);
+ compose->width = format->width;
+ compose->height = format->height;
+
+ fmt->format = *format;
+ return 0;
+}
+
+static int mt9m113_ifp_get_selection(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state,
+ struct v4l2_subdev_selection *sel)
+{
+ if (sel->pad != 0)
+ return -EINVAL;
+
+ switch (sel->target) {
+ case V4L2_SEL_TGT_CROP:
+ sel->r = *v4l2_subdev_state_get_crop(state, 0);
+ return 0;
+
+ case V4L2_SEL_TGT_COMPOSE:
+ sel->r = *v4l2_subdev_state_get_compose(state, 0);
+ return 0;
+
+ case V4L2_SEL_TGT_CROP_DEFAULT:
+ case V4L2_SEL_TGT_CROP_BOUNDS:
+ sel->r.left = 0;
+ sel->r.top = 0;
+ sel->r.width = MT9M113_PIXEL_ARRAY_WIDTH;
+ sel->r.height = MT9M113_PIXEL_ARRAY_HEIGHT;
+ return 0;
+
+ case V4L2_SEL_TGT_COMPOSE_DEFAULT:
+ case V4L2_SEL_TGT_COMPOSE_BOUNDS:
+ sel->r.left = 0;
+ sel->r.top = 0;
+ sel->r.width = MT9M113_PIXEL_ARRAY_WIDTH;
+ sel->r.height = MT9M113_PIXEL_ARRAY_HEIGHT;
+ return 0;
+
+ default:
+ return -EINVAL;
+ }
+}
+
+/* IFP registered callback - registers PA and creates link */
+static void mt9m113_ifp_unregistered(struct v4l2_subdev *sd)
+{
+ struct mt9m113 *sensor = ifp_to_mt9m113(sd);
+
+ v4l2_device_unregister_subdev(&sensor->pa.sd);
+}
+
+static int mt9m113_ifp_registered(struct v4l2_subdev *sd)
+{
+ struct mt9m113 *sensor = ifp_to_mt9m113(sd);
+ int ret;
+
+ ret = v4l2_device_register_subdev(sd->v4l2_dev, &sensor->pa.sd);
+ if (ret < 0) {
+ dev_err(&sensor->client->dev,
+ "Failed to register pixel array subdev\n");
+ return ret;
+ }
+
+ ret = media_create_pad_link(&sensor->pa.sd.entity, 0,
+ &sensor->ifp.sd.entity, 0,
+ MEDIA_LNK_FL_ENABLED |
+ MEDIA_LNK_FL_IMMUTABLE);
+ if (ret < 0) {
+ dev_err(&sensor->client->dev,
+ "Failed to link pixel array to ifp\n");
+ v4l2_device_unregister_subdev(&sensor->pa.sd);
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct v4l2_subdev_video_ops mt9m113_ifp_video_ops = {
+ .s_stream = mt9m113_ifp_s_stream,
+};
+
+static const struct v4l2_subdev_pad_ops mt9m113_ifp_pad_ops = {
+ .enum_mbus_code = mt9m113_ifp_enum_mbus_code,
+ .enum_frame_size = mt9m113_ifp_enum_frame_size,
+ .enum_frame_interval = mt9m113_ifp_enum_frame_interval,
+ .get_fmt = v4l2_subdev_get_fmt,
+ .set_fmt = mt9m113_ifp_set_fmt,
+ .get_frame_interval = mt9m113_ifp_g_frame_interval,
+ .get_selection = mt9m113_ifp_get_selection,
+};
+
+static const struct v4l2_subdev_ops mt9m113_ifp_ops = {
+ .video = &mt9m113_ifp_video_ops,
+ .pad = &mt9m113_ifp_pad_ops,
+};
+
+static const struct v4l2_subdev_internal_ops mt9m113_ifp_internal_ops = {
+ .init_state = mt9m113_ifp_init_state,
+ .registered = mt9m113_ifp_registered,
+ .unregistered = mt9m113_ifp_unregistered,
+};
+
+/* -----------------------------------------------------------------------------
+ * Controls
+ */
+
+/*
+ * Menu items map directly to MT9M113_TEST_MODE_* values in datasheet order
+ * (MT9M113 datasheet R0x0066 "Test Pattern Generator"). The driver writes
+ * the menu index unchanged to MT9M113_MODE_TEST_MODE; no value translation
+ * is needed.
+ */
+static const char * const mt9m113_test_pattern_menu[] = {
+ "Disabled",
+ "Solid White",
+ "Grey Ramp",
+ "Color Bar Ramp",
+ "Solid White (Color Bars)",
+ "Noise",
+};
+
+static int mt9m113_s_ctrl(struct v4l2_ctrl *ctrl)
+{
+ struct mt9m113 *sensor = container_of(ctrl->handler,
+ struct mt9m113, ifp.hdl);
+ int pm_ret, ret = 0;
+
+ /*
+ * pm_runtime_get_if_in_use() returns >0 on success (HW active, kref
+ * incremented), 0 if the device is suspended, and -EINVAL when
+ * CONFIG_PM is disabled. Treat -EINVAL as "PM core is absent, HW is
+ * always on" and proceed without taking a kref (the matching put at
+ * the tail must then be skipped). Only 0 means "skip silently".
+ */
+ pm_ret = pm_runtime_get_if_in_use(&sensor->client->dev);
+ if (pm_ret == 0)
+ return 0;
+
+ switch (ctrl->id) {
+ case V4L2_CID_HFLIP: {
+ u64 mode_a, mode_b;
+
+ ret = mt9m113_read_mcu_var(sensor, MT9M113_SENSOR_READ_MODE_A,
+ &mode_a);
+ if (ret)
+ break;
+ ret = mt9m113_read_mcu_var(sensor, MT9M113_SENSOR_READ_MODE_B,
+ &mode_b);
+ if (ret)
+ break;
+
+ if (ctrl->val) {
+ mode_a |= MT9M113_SENSOR_READ_MODE_HMIRROR;
+ mode_b |= MT9M113_SENSOR_READ_MODE_HMIRROR;
+ } else {
+ mode_a &= ~MT9M113_SENSOR_READ_MODE_HMIRROR;
+ mode_b &= ~MT9M113_SENSOR_READ_MODE_HMIRROR;
+ }
+
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_SENSOR_READ_MODE_A,
+ mode_a);
+ if (!ret)
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_SENSOR_READ_MODE_B,
+ mode_b);
+ /*
+ * Only refresh if streaming and the MCU is not held in boot
+ * mode for the test pattern - calling REFRESH while the MCU
+ * is halted (test_pattern_active) blocks for two 500 ms
+ * SEQ_CMD timeouts and never applies the new control.
+ */
+ if (!ret && sensor->streaming && !sensor->test_pattern_active)
+ mt9m113_refresh(sensor);
+ break;
+ }
+
+ case V4L2_CID_VFLIP: {
+ u64 mode_a, mode_b;
+
+ ret = mt9m113_read_mcu_var(sensor, MT9M113_SENSOR_READ_MODE_A,
+ &mode_a);
+ if (ret)
+ break;
+ ret = mt9m113_read_mcu_var(sensor, MT9M113_SENSOR_READ_MODE_B,
+ &mode_b);
+ if (ret)
+ break;
+
+ if (ctrl->val) {
+ mode_a |= MT9M113_SENSOR_READ_MODE_VMIRROR;
+ mode_b |= MT9M113_SENSOR_READ_MODE_VMIRROR;
+ } else {
+ mode_a &= ~MT9M113_SENSOR_READ_MODE_VMIRROR;
+ mode_b &= ~MT9M113_SENSOR_READ_MODE_VMIRROR;
+ }
+
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_SENSOR_READ_MODE_A,
+ mode_a);
+ if (!ret)
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_SENSOR_READ_MODE_B,
+ mode_b);
+ /*
+ * Only refresh if streaming and the MCU is not held in boot
+ * mode for the test pattern - calling REFRESH while the MCU
+ * is halted (test_pattern_active) blocks for two 500 ms
+ * SEQ_CMD timeouts and never applies the new control.
+ */
+ if (!ret && sensor->streaming && !sensor->test_pattern_active)
+ mt9m113_refresh(sensor);
+ break;
+ }
+
+ case V4L2_CID_COLORFX: {
+ u16 effect;
+
+ switch (ctrl->val) {
+ case V4L2_COLORFX_NONE:
+ effect = MT9M113_SPEC_EFFECTS_NONE;
+ break;
+ case V4L2_COLORFX_BW:
+ effect = MT9M113_SPEC_EFFECTS_MONOCHROME;
+ break;
+ case V4L2_COLORFX_SEPIA:
+ effect = MT9M113_SPEC_EFFECTS_SEPIA;
+ break;
+ case V4L2_COLORFX_NEGATIVE:
+ effect = MT9M113_SPEC_EFFECTS_NEGATIVE;
+ break;
+ case V4L2_COLORFX_SOLARIZATION:
+ effect = MT9M113_SPEC_EFFECTS_SOLARIZE;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ if (!ret) {
+ effect |= (MT9M113_SPEC_EFFECTS_DEFAULT &
+ ~MT9M113_SPEC_EFFECTS_MASK);
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SPEC_EFFECTS_A,
+ effect);
+ if (!ret)
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_SPEC_EFFECTS_B,
+ effect);
+
+ /* See HFLIP/VFLIP: skip refresh while test_pattern halts MCU. */
+ if (!ret && sensor->streaming && !sensor->test_pattern_active)
+ mt9m113_refresh(sensor);
+ }
+ break;
+ }
+
+ case V4L2_CID_POWER_LINE_FREQUENCY: {
+ u8 fd_mode;
+
+ switch (ctrl->val) {
+ case V4L2_CID_POWER_LINE_FREQUENCY_DISABLED:
+ fd_mode = MT9M113_FD_MODE_DISABLED;
+ break;
+ case V4L2_CID_POWER_LINE_FREQUENCY_50HZ:
+ fd_mode = MT9M113_FD_MODE_50HZ;
+ break;
+ case V4L2_CID_POWER_LINE_FREQUENCY_60HZ:
+ fd_mode = MT9M113_FD_MODE_60HZ;
+ break;
+ case V4L2_CID_POWER_LINE_FREQUENCY_AUTO:
+ fd_mode = MT9M113_FD_MODE_AUTO;
+ break;
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ if (!ret)
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_FD_MODE,
+ fd_mode);
+ break;
+ }
+
+ case V4L2_CID_SATURATION:
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AWB_SATURATION,
+ ctrl->val);
+ /*
+ * Only refresh if streaming and the MCU is not held in boot
+ * mode for the test pattern - calling REFRESH while the MCU
+ * is halted (test_pattern_active) blocks for two 500 ms
+ * SEQ_CMD timeouts and never applies the new control.
+ */
+ if (!ret && sensor->streaming && !sensor->test_pattern_active)
+ mt9m113_refresh(sensor);
+ break;
+
+ case V4L2_CID_EXPOSURE_AUTO:
+ /* Enable/disable internal AE algorithm via AE_GATE */
+ if (ctrl->val == V4L2_EXPOSURE_AUTO)
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_GATE,
+ MT9M113_AE_GATE_ENABLE);
+ else
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AE_GATE,
+ MT9M113_AE_GATE_DISABLE);
+ break;
+
+ case V4L2_CID_EXPOSURE:
+ /* Write coarse integration time to both contexts */
+ ret = cci_write(sensor->regmap, MT9M113_COARSE_IT_TIME_A,
+ ctrl->val, NULL);
+ if (!ret)
+ ret = cci_write(sensor->regmap, MT9M113_COARSE_IT_TIME_B,
+ ctrl->val, NULL);
+ break;
+
+ case V4L2_CID_ANALOGUE_GAIN:
+ /* Write analog gain register */
+ ret = cci_write(sensor->regmap, MT9M113_ANALOG_GAIN,
+ ctrl->val, NULL);
+ break;
+
+ case V4L2_CID_AUTO_WHITE_BALANCE:
+ /* Enable/disable internal AWB via awb_mode */
+ ret = mt9m113_write_mcu_var(sensor, MT9M113_AWB_MODE,
+ ctrl->val ? 0x02 : 0x00);
+ break;
+
+ case V4L2_CID_TEST_PATTERN:
+ if (ctrl->val == 0) {
+ /*
+ * Disable test pattern. Only restart MCU if test
+ * pattern was previously active. On first call
+ * (ctrl_handler_setup default), the MCU is already
+ * in normal mode - restarting it here would disrupt
+ * the MCU state and cause REFRESH timeouts.
+ *
+ * Keep test_pattern_active set until both writes
+ * succeed: a half-applied disable leaves the MCU
+ * halted, and a subsequent CID=0 must be allowed to
+ * retry the full sequence.
+ */
+ if (sensor->test_pattern_active) {
+ dev_dbg(&sensor->client->dev,
+ "MT9M113: Disabling test pattern, restarting MCU\n");
+ /*
+ * Reverse of mt9m113_apply_test_pattern(): release
+ * the MCU from halt, write MODE_TEST_MODE=0, and
+ * REFRESH if streaming so the sequencer reverts to
+ * the normal sensor stream and frames resume.
+ */
+ cci_write(sensor->regmap, MT9M113_MCU_BOOT_MODE,
+ 0x0000, &ret);
+ if (!ret) {
+ usleep_range(10000, 15000);
+ ret = mt9m113_write_mcu_var(sensor,
+ MT9M113_MODE_TEST_MODE,
+ MT9M113_TEST_MODE_DISABLED);
+ }
+ if (!ret && sensor->streaming)
+ ret = mt9m113_refresh(sensor);
+ if (!ret) {
+ sensor->test_pattern_active = false;
+ sensor->test_pattern_value = 0;
+ }
+ }
+ } else {
+ /*
+ * Enable test pattern mode.
+ *
+ * Only commit the MCU vars + halt here while we're
+ * already streaming. Otherwise the MCU is asleep
+ * (autosuspend) or not yet running the sequencer,
+ * and either the writes would race a power_on or
+ * the subsequent normal stream init would overwrite
+ * MODE_SELECT. Cache the requested pattern in
+ * test_pattern_value so mt9m113_stream_on() can
+ * replay the apply at the end of its normal-init
+ * sequence without doing a v4l2_ctrl_find() lookup
+ * (which would self-deadlock on the ctrl-handler
+ * mutex that the V4L2 core holds across s_stream).
+ */
+ sensor->test_pattern_active = true;
+ sensor->test_pattern_value = ctrl->val;
+ dev_dbg(&sensor->client->dev,
+ "MT9M113: Enabling test pattern %d\n", ctrl->val);
+ if (sensor->streaming)
+ ret = mt9m113_apply_test_pattern(sensor,
+ ctrl->val);
+ }
+ break;
+
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ if (pm_ret > 0)
+ pm_runtime_put_autosuspend(&sensor->client->dev);
+ return ret;
+}
+
+static const struct v4l2_ctrl_ops mt9m113_ctrl_ops = {
+ .s_ctrl = mt9m113_s_ctrl,
+};
+
+/* -----------------------------------------------------------------------------
+ * Power Management
+ */
+
+static int mt9m113_power_on(struct mt9m113 *sensor)
+{
+ struct device *dev = &sensor->client->dev;
+ int ret;
+
+ ret = regulator_bulk_enable(ARRAY_SIZE(sensor->supplies),
+ sensor->supplies);
+ if (ret < 0)
+ return ret;
+
+ /*
+ * Aptina/onsemi SOC sensors require EXTCLK to be running before
+ * STANDBY (powerdown) is released; otherwise the internal
+ * clock-domain state machines come out of reset non-deterministically
+ * and the MCU can wedge on SEQ_CMD. Enable the clock first, let the
+ * supplies and clock settle, then deassert powerdown.
+ */
+ ret = clk_prepare_enable(sensor->clk);
+ if (ret < 0)
+ goto error_regulator;
+
+ usleep_range(20000, 25000);
+
+ if (sensor->powerdown)
+ gpiod_set_value_cansleep(sensor->powerdown, 0);
+
+ msleep(20);
+
+ if (sensor->reset) {
+ gpiod_set_value_cansleep(sensor->reset, 1);
+ usleep_range(1000, 2000);
+ gpiod_set_value_cansleep(sensor->reset, 0);
+ usleep_range(44500, 50000);
+ } else if (sensor->powerdown) {
+ usleep_range(44500, 50000);
+ }
+
+ /* MT9M113 MCU boot sequence */
+ {
+ u64 clocks_val = 0;
+
+ cci_read(sensor->regmap, MT9M113_CLOCKS_CONTROL, &clocks_val, NULL);
+ if (clocks_val != 0) {
+ u64 seq_cmd = 0;
+ int read_ret;
+
+ /*
+ * Sensor already has clocks running (warm reboot or
+ * resume). Check if MCU is responsive by reading
+ * SEQ_CMD. If stuck (non-zero) or if the read itself
+ * failed (I2C error), force the soft-reset path instead
+ * of silently returning success on an uninitialised
+ * sensor.
+ */
+ read_ret = mt9m113_read_mcu_var(sensor, MT9M113_SEQ_CMD,
+ &seq_cmd);
+ if (read_ret == 0 && seq_cmd == 0) {
+ dev_dbg(dev, "MT9M113 already initialized, MCU OK\n");
+ msleep(50);
+ return 0;
+ }
+ if (read_ret < 0)
+ dev_warn(dev,
+ "MT9M113: SEQ_CMD read failed (%d), forcing soft reset\n",
+ read_ret);
+ else
+ dev_warn(dev,
+ "MT9M113: MCU stuck (SEQ_CMD=0x%llx), forcing soft reset\n",
+ seq_cmd);
+ }
+
+ /* Soft reset */
+ cci_write(sensor->regmap, MT9M113_RESET_AND_MISC_CONTROL,
+ MT9M113_RESET_SOC, &ret);
+ cci_write(sensor->regmap, MT9M113_RESET_AND_MISC_CONTROL,
+ 0, &ret);
+ if (ret < 0)
+ goto error_clock;
+ msleep(200);
+
+ /* Boot MCU */
+ cci_write(sensor->regmap, MT9M113_MCU_BOOT_MODE, 0x0001, &ret);
+ usleep_range(1000, 2000);
+ cci_write(sensor->regmap, MT9M113_MCU_BOOT_MODE, 0x0000, &ret);
+ if (ret < 0)
+ goto error_clock;
+ msleep(200);
+
+ /* Configure PLL */
+ cci_write(sensor->regmap, MT9M113_CLOCKS_CONTROL, 0x00FF, &ret);
+ cci_write(sensor->regmap, MT9M113_STANDBY_CONTROL,
+ MT9M113_STANDBY_CONTROL_ACTIVE, &ret);
+ cci_write(sensor->regmap, MT9M113_PLL_CONTROL, 0x2145, &ret);
+ cci_write(sensor->regmap, MT9M113_PLL_CONTROL, 0x2145, &ret);
+ cci_write(sensor->regmap, MT9M113_PLL_CONTROL, 0x2145, &ret);
+ cci_write(sensor->regmap, MT9M113_PLL_DIVIDERS, 0x0114, &ret);
+ cci_write(sensor->regmap, MT9M113_PLL_P_DIVIDERS, 0x00F1, &ret);
+ cci_write(sensor->regmap, MT9M113_PLL_CONTROL, 0x2545, &ret);
+ cci_write(sensor->regmap, MT9M113_PLL_CONTROL, 0x2547, &ret);
+ cci_write(sensor->regmap, MT9M113_PLL_CONTROL, 0x3447, &ret);
+ if (ret < 0)
+ goto error_clock;
+ msleep(20);
+ cci_write(sensor->regmap, MT9M113_PLL_CONTROL, 0x3047, &ret);
+ cci_write(sensor->regmap, MT9M113_PLL_CONTROL, 0x3046, &ret);
+ cci_write(sensor->regmap, MT9M113_RESET_AND_MISC_CONTROL, 0x0218, &ret);
+ /* Keep the MCU active (do not enter standby 0x002A) after power-on. */
+ cci_write(sensor->regmap, MT9M113_STANDBY_CONTROL,
+ MT9M113_STANDBY_CONTROL_ACTIVE, &ret);
+ if (ret < 0)
+ goto error_clock;
+ msleep(50);
+
+ /* Configure OFIFO */
+ cci_write(sensor->regmap, MT9M113_OFIFO_CONTROL_STATUS, 0x0003, &ret);
+ if (ret < 0)
+ goto error_clock;
+ }
+
+ return 0;
+
+error_clock:
+ clk_disable_unprepare(sensor->clk);
+error_regulator:
+ if (sensor->powerdown)
+ gpiod_set_value_cansleep(sensor->powerdown, 1);
+ else if (sensor->reset)
+ gpiod_set_value_cansleep(sensor->reset, 1);
+ regulator_bulk_disable(ARRAY_SIZE(sensor->supplies),
+ sensor->supplies);
+ return ret;
+}
+
+static void mt9m113_power_off(struct mt9m113 *sensor)
+{
+ /*
+ * Symmetric with mt9m113_power_on(): hold the chip in reset, then
+ * gate the clock and drop the supplies so the enable/disable refcount
+ * stays balanced across runtime-PM cycles and the MCU is fully reset.
+ *
+ * Prefer the powerdown GPIO when available; fall back to driving
+ * RESET_BAR active so it is not left floating after VDD drops on
+ * boards that only wire reset-gpios. Mirror the settling gaps from
+ * power_on so the MCU sees a clean down-then-up sequence across
+ * runtime-PM cycles.
+ */
+ if (sensor->powerdown)
+ gpiod_set_value_cansleep(sensor->powerdown, 1);
+ else if (sensor->reset)
+ gpiod_set_value_cansleep(sensor->reset, 1);
+ usleep_range(1000, 2000);
+ clk_disable_unprepare(sensor->clk);
+ usleep_range(1000, 2000);
+ regulator_bulk_disable(ARRAY_SIZE(sensor->supplies),
+ sensor->supplies);
+}
+
+static int mt9m113_runtime_resume(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct mt9m113 *sensor = ifp_to_mt9m113(sd);
+ int ret;
+
+ /*
+ * Always power-cycle and re-initialise on resume, including when a
+ * powerdown GPIO is present. The MT9M113 MCU must be hardware-reset
+ * (powerdown + clock) and re-initialised on each session, otherwise a
+ * wedged MCU (SEQ_CMD/0xA103 stuck) is never recovered and only a
+ * physical power cycle helps - matching the legacy vendor kernel per-open behaviour.
+ */
+ ret = mt9m113_power_on(sensor);
+ if (ret)
+ return ret;
+
+ ret = mt9m113_sensor_init(sensor);
+ if (ret) {
+ /*
+ * sensor_init() can fail (-ETIMEDOUT on an MCU lockup, I2C
+ * errors); on that path the PM core reverts runtime_status to
+ * SUSPENDED without touching driver-side state, so the
+ * clk/regulator refcounts taken in power_on() would otherwise
+ * leak and the next resume would double-enable them.
+ */
+ mt9m113_power_off(sensor);
+ return ret;
+ }
+
+ return 0;
+}
+
+static int mt9m113_runtime_suspend(struct device *dev)
+{
+ struct v4l2_subdev *sd = dev_get_drvdata(dev);
+ struct mt9m113 *sensor = ifp_to_mt9m113(sd);
+
+ /* Power down (powerdown GPIO + clock off) so the MCU is reset next resume. */
+ mt9m113_power_off(sensor);
+ return 0;
+}
+
+static DEFINE_RUNTIME_DEV_PM_OPS(mt9m113_pm_ops,
+ mt9m113_runtime_suspend,
+ mt9m113_runtime_resume,
+ NULL);
+
+/* -----------------------------------------------------------------------------
+ * Probe & Remove
+ */
+
+static int mt9m113_identify(struct mt9m113 *sensor)
+{
+ u64 value;
+ int ret;
+
+ ret = cci_read(sensor->regmap, MT9M113_CHIP_ID, &value, NULL);
+ if (ret) {
+ dev_err(&sensor->client->dev, "Failed to read chip ID\n");
+ return -ENXIO;
+ }
+
+ if (value != MT9M113_CHIP_ID_VALUE) {
+ dev_err(&sensor->client->dev,
+ "Invalid chip ID 0x%04llx (expected 0x%04x)\n",
+ value, MT9M113_CHIP_ID_VALUE);
+ return -ENXIO;
+ }
+
+ dev_dbg(&sensor->client->dev, "MT9M113 detected (ID 0x%04llx)\n",
+ value);
+ return 0;
+}
+
+static int mt9m113_parse_dt(struct mt9m113 *sensor)
+{
+ struct fwnode_handle *fwnode = dev_fwnode(&sensor->client->dev);
+ struct fwnode_handle *ep;
+ int ret;
+
+ ep = fwnode_graph_get_next_endpoint(fwnode, NULL);
+ if (!ep)
+ return -EINVAL;
+
+ sensor->bus_cfg.bus_type = V4L2_MBUS_UNKNOWN;
+ ret = v4l2_fwnode_endpoint_alloc_parse(ep, &sensor->bus_cfg);
+ fwnode_handle_put(ep);
+ if (ret < 0)
+ return ret;
+
+ if (sensor->bus_cfg.bus_type != V4L2_MBUS_CSI2_DPHY) {
+ dev_err(&sensor->client->dev, "Unsupported bus type %d\n",
+ sensor->bus_cfg.bus_type);
+ v4l2_fwnode_endpoint_free(&sensor->bus_cfg);
+ return -EINVAL;
+ }
+
+ if (sensor->bus_cfg.nr_of_link_frequencies < 1) {
+ dev_err(&sensor->client->dev, "no link-frequencies specified\n");
+ v4l2_fwnode_endpoint_free(&sensor->bus_cfg);
+ return -EINVAL;
+ }
+
+ /*
+ * The MT9M113 has a single-lane MIPI CSI-2 D-PHY interface, so the
+ * binding no longer advertises data-lanes (a maxItems=1 array adds no
+ * information). v4l2_fwnode_endpoint_parse() therefore leaves
+ * num_data_lanes at 0; force it to 1 so the pixrate calculation
+ * below has a non-zero multiplier and receivers like camss size the
+ * CSI-2 link budget correctly.
+ */
+ if (sensor->bus_cfg.bus.mipi_csi2.num_data_lanes == 0)
+ sensor->bus_cfg.bus.mipi_csi2.num_data_lanes = 1;
+
+ if (sensor->bus_cfg.bus.mipi_csi2.num_data_lanes != 1) {
+ dev_err(&sensor->client->dev,
+ "unsupported data-lanes count %u (must be 1)\n",
+ sensor->bus_cfg.bus.mipi_csi2.num_data_lanes);
+ v4l2_fwnode_endpoint_free(&sensor->bus_cfg);
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int mt9m113_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct mt9m113 *sensor;
+ int ret;
+
+ sensor = devm_kzalloc(dev, sizeof(*sensor), GFP_KERNEL);
+ if (!sensor)
+ return -ENOMEM;
+
+ sensor->client = client;
+
+ sensor->regmap = devm_cci_regmap_init_i2c(client, 16);
+ if (IS_ERR(sensor->regmap))
+ return PTR_ERR(sensor->regmap);
+
+ ret = mt9m113_parse_dt(sensor);
+ if (ret < 0)
+ return ret;
+
+ sensor->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(sensor->clk)) {
+ ret = PTR_ERR(sensor->clk);
+ goto error_ep_free;
+ }
+
+ sensor->reset = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(sensor->reset)) {
+ ret = PTR_ERR(sensor->reset);
+ goto error_ep_free;
+ }
+
+ sensor->powerdown = devm_gpiod_get_optional(dev, "powerdown",
+ GPIOD_OUT_HIGH);
+ if (IS_ERR(sensor->powerdown)) {
+ ret = PTR_ERR(sensor->powerdown);
+ goto error_ep_free;
+ }
+
+ sensor->supplies[0].supply = "vddio";
+ sensor->supplies[1].supply = "vdd";
+ sensor->supplies[2].supply = "vaa";
+
+ ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(sensor->supplies),
+ sensor->supplies);
+ if (ret < 0)
+ goto error_ep_free;
+
+ /* Power on and identify */
+ ret = mt9m113_power_on(sensor);
+ if (ret < 0)
+ goto error_ep_free;
+
+ ret = mt9m113_identify(sensor);
+ if (ret < 0)
+ goto error_power_off;
+
+ ret = mt9m113_sensor_init(sensor);
+ if (ret < 0)
+ goto error_power_off;
+
+ /*
+ * The CSI-2 link frequency is mandatory (enforced by the binding and
+ * mt9m113_parse_dt()). Derive the pixel rate from it: every supported
+ * source format is 16 bits/pixel on the bus and the D-PHY clocks data
+ * DDR, so pixel_rate = link_freq * 2 * lanes / bpp.
+ */
+ sensor->link_freq = sensor->bus_cfg.link_frequencies[0];
+ sensor->pixrate = div_u64(2ULL * sensor->link_freq *
+ sensor->bus_cfg.bus.mipi_csi2.num_data_lanes,
+ 16);
+
+ dev_dbg(dev, "MT9M113: link freq %lld Hz, pixel rate %u Hz\n",
+ sensor->link_freq, sensor->pixrate);
+
+ /* Initialize Pixel Array subdev */
+ v4l2_subdev_init(&sensor->pa.sd, &mt9m113_pa_ops);
+ sensor->pa.sd.internal_ops = &mt9m113_pa_internal_ops;
+ v4l2_i2c_subdev_set_name(&sensor->pa.sd, client, NULL, " pixel array");
+ sensor->pa.sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ sensor->pa.sd.owner = THIS_MODULE;
+ sensor->pa.sd.dev = dev;
+ v4l2_set_subdevdata(&sensor->pa.sd, client);
+ sensor->pa.sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
+ sensor->pa.pad.flags = MEDIA_PAD_FL_SOURCE;
+ ret = media_entity_pads_init(&sensor->pa.sd.entity, 1, &sensor->pa.pad);
+ if (ret < 0)
+ goto error_pa_entity;
+
+ /*
+ * LINK_FREQ and PIXEL_RATE live on the pixel-array subdev because
+ * receivers walk the media graph upstream until they reach the
+ * MEDIA_ENT_F_CAM_SENSOR entity and read these controls from that
+ * subdev's handler (see camss_find_sensor_pad() / v4l2_get_link_freq()
+ * in drivers/media/platform/qcom/camss/camss.c). The IFP is a
+ * MEDIA_ENT_F_PROC_VIDEO_ISP and the walk does not stop there, so
+ * controls on the IFP alone are invisible to the receiver and the
+ * pipeline fails at CSIPHY stream-on with -EINVAL.
+ */
+ v4l2_ctrl_handler_init(&sensor->pa.hdl, 2);
+ {
+ struct v4l2_ctrl *link_freq_ctrl;
+
+ link_freq_ctrl = v4l2_ctrl_new_int_menu(&sensor->pa.hdl, NULL,
+ V4L2_CID_LINK_FREQ,
+ sensor->bus_cfg.nr_of_link_frequencies - 1, 0,
+ sensor->bus_cfg.link_frequencies);
+ if (link_freq_ctrl)
+ link_freq_ctrl->flags |= V4L2_CTRL_FLAG_READ_ONLY;
+ }
+ v4l2_ctrl_new_std(&sensor->pa.hdl, NULL, V4L2_CID_PIXEL_RATE,
+ sensor->pixrate, sensor->pixrate, 1, sensor->pixrate);
+ if (sensor->pa.hdl.error) {
+ ret = sensor->pa.hdl.error;
+ goto error_pa_handler;
+ }
+ sensor->pa.sd.ctrl_handler = &sensor->pa.hdl;
+ sensor->pa.sd.state_lock = sensor->pa.hdl.lock;
+
+ ret = v4l2_subdev_init_finalize(&sensor->pa.sd);
+ if (ret < 0)
+ goto error_pa_handler;
+
+ /* Initialize IFP subdev */
+ v4l2_i2c_subdev_init(&sensor->ifp.sd, client, &mt9m113_ifp_ops);
+ v4l2_i2c_subdev_set_name(&sensor->ifp.sd, client, NULL, " ifp");
+ sensor->ifp.sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+ sensor->ifp.sd.internal_ops = &mt9m113_ifp_internal_ops;
+ sensor->ifp.sd.entity.function = MEDIA_ENT_F_PROC_VIDEO_ISP;
+ sensor->ifp.pads[0].flags = MEDIA_PAD_FL_SINK;
+ sensor->ifp.pads[1].flags = MEDIA_PAD_FL_SOURCE;
+ ret = media_entity_pads_init(&sensor->ifp.sd.entity, 2, sensor->ifp.pads);
+ if (ret < 0)
+ goto error_ifp_entity;
+
+ /* Initialize controls on IFP */
+ v4l2_ctrl_handler_init(&sensor->ifp.hdl, 10);
+ v4l2_ctrl_new_std(&sensor->ifp.hdl, &mt9m113_ctrl_ops,
+ V4L2_CID_HFLIP, 0, 1, 1, 0);
+ v4l2_ctrl_new_std(&sensor->ifp.hdl, &mt9m113_ctrl_ops,
+ V4L2_CID_VFLIP, 0, 1, 1, 0);
+ /* COLORFX: mask out unsupported effects 4-12 (EMBOSS through SILHOUETTE) */
+ v4l2_ctrl_new_std_menu(&sensor->ifp.hdl, &mt9m113_ctrl_ops,
+ V4L2_CID_COLORFX,
+ V4L2_COLORFX_SOLARIZATION, 0x1ff0,
+ V4L2_COLORFX_NONE);
+ v4l2_ctrl_new_std_menu(&sensor->ifp.hdl, &mt9m113_ctrl_ops,
+ V4L2_CID_POWER_LINE_FREQUENCY,
+ V4L2_CID_POWER_LINE_FREQUENCY_AUTO, 0,
+ V4L2_CID_POWER_LINE_FREQUENCY_AUTO);
+ v4l2_ctrl_new_std(&sensor->ifp.hdl, &mt9m113_ctrl_ops,
+ V4L2_CID_SATURATION, 0, 255, 1, 128);
+ v4l2_ctrl_new_std_menu(&sensor->ifp.hdl, &mt9m113_ctrl_ops,
+ V4L2_CID_EXPOSURE_AUTO,
+ V4L2_EXPOSURE_MANUAL, 0,
+ V4L2_EXPOSURE_AUTO);
+ v4l2_ctrl_new_std(&sensor->ifp.hdl, &mt9m113_ctrl_ops,
+ V4L2_CID_EXPOSURE, 1, 1000, 1, 100);
+ v4l2_ctrl_new_std(&sensor->ifp.hdl, &mt9m113_ctrl_ops,
+ V4L2_CID_ANALOGUE_GAIN, 0, 127, 1, 32);
+ v4l2_ctrl_new_std(&sensor->ifp.hdl, &mt9m113_ctrl_ops,
+ V4L2_CID_AUTO_WHITE_BALANCE, 0, 1, 1, 1);
+ v4l2_ctrl_new_std_menu_items(&sensor->ifp.hdl, &mt9m113_ctrl_ops,
+ V4L2_CID_TEST_PATTERN,
+ ARRAY_SIZE(mt9m113_test_pattern_menu) - 1,
+ 0, 0, mt9m113_test_pattern_menu);
+
+ if (sensor->ifp.hdl.error) {
+ ret = sensor->ifp.hdl.error;
+ goto error_ifp_handler;
+ }
+
+ sensor->ifp.sd.ctrl_handler = &sensor->ifp.hdl;
+ sensor->ifp.sd.state_lock = sensor->ifp.hdl.lock;
+
+ ret = v4l2_subdev_init_finalize(&sensor->ifp.sd);
+ if (ret < 0)
+ goto error_ifp_handler;
+
+ /*
+ * Enable runtime PM. Configure autosuspend before enabling the
+ * runtime PM core so a put issued between enable and use_autosuspend
+ * cannot race with autosuspend being unconfigured. The 2 s autosuspend
+ * delay amortises the unconditional power-cycle + full init-table
+ * replay in runtime_resume over typical preview/snapshot sequences:
+ * the cold init is load-bearing for MCU-wedge recovery so it cannot
+ * be conditionalised on health, only amortised.
+ */
+ pm_runtime_set_active(dev);
+ pm_runtime_get_noresume(dev);
+ pm_runtime_set_autosuspend_delay(dev, 2000);
+ pm_runtime_use_autosuspend(dev);
+ pm_runtime_enable(dev);
+
+ /* Register only the IFP - PA will be registered in ifp_registered callback */
+ ret = v4l2_async_register_subdev(&sensor->ifp.sd);
+ if (ret < 0)
+ goto error_pm;
+
+ pm_runtime_put_autosuspend(dev);
+
+ dev_dbg(dev, "MT9M113 driver with IFP sub-device initialized\n");
+ return 0;
+
+error_pm:
+ pm_runtime_disable(dev);
+ pm_runtime_set_suspended(dev);
+ pm_runtime_dont_use_autosuspend(dev);
+ pm_runtime_put_noidle(dev);
+error_ifp_handler:
+ v4l2_subdev_cleanup(&sensor->ifp.sd);
+ v4l2_ctrl_handler_free(&sensor->ifp.hdl);
+error_ifp_entity:
+ media_entity_cleanup(&sensor->ifp.sd.entity);
+ v4l2_subdev_cleanup(&sensor->pa.sd);
+error_pa_handler:
+ v4l2_ctrl_handler_free(&sensor->pa.hdl);
+error_pa_entity:
+ media_entity_cleanup(&sensor->pa.sd.entity);
+error_power_off:
+ mt9m113_power_off(sensor);
+error_ep_free:
+ v4l2_fwnode_endpoint_free(&sensor->bus_cfg);
+ return ret;
+}
+
+static void mt9m113_remove(struct i2c_client *client)
+{
+ struct v4l2_subdev *sd = i2c_get_clientdata(client);
+ struct mt9m113 *sensor = ifp_to_mt9m113(sd);
+ struct device *dev = &client->dev;
+
+ v4l2_async_unregister_subdev(&sensor->ifp.sd);
+ v4l2_subdev_cleanup(&sensor->ifp.sd);
+ v4l2_ctrl_handler_free(&sensor->ifp.hdl);
+ media_entity_cleanup(&sensor->ifp.sd.entity);
+
+ v4l2_subdev_cleanup(&sensor->pa.sd);
+ v4l2_ctrl_handler_free(&sensor->pa.hdl);
+ media_entity_cleanup(&sensor->pa.sd.entity);
+
+ v4l2_fwnode_endpoint_free(&sensor->bus_cfg);
+
+ pm_runtime_disable(dev);
+ pm_runtime_dont_use_autosuspend(dev);
+ if (!pm_runtime_status_suspended(dev))
+ mt9m113_power_off(sensor);
+ pm_runtime_set_suspended(dev);
+}
+
+static const struct of_device_id mt9m113_of_ids[] = {
+ { .compatible = "aptina,mt9m113" },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, mt9m113_of_ids);
+
+static const struct i2c_device_id mt9m113_id[] = {
+ { "mt9m113" },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(i2c, mt9m113_id);
+
+static struct i2c_driver mt9m113_driver = {
+ .driver = {
+ .name = "mt9m113",
+ .pm = pm_ptr(&mt9m113_pm_ops),
+ .of_match_table = mt9m113_of_ids,
+ },
+ .probe = mt9m113_probe,
+ .remove = mt9m113_remove,
+ .id_table = mt9m113_id,
+};
+
+module_i2c_driver(mt9m113_driver);
+
+MODULE_AUTHOR("Herman van Hazendonk <github.com@herrie.org>");
+MODULE_DESCRIPTION("Aptina MT9M113 Sensor Driver");
+MODULE_LICENSE("GPL");
--
2.43.0
^ permalink raw reply related [flat|nested] 4+ messages in thread