[PATCH v5 0/4] arm64: dts: nuvoton: add NPCM845 SoC and EVB support

[PATCH v5 0/4] arm64: dts: nuvoton: add NPCM845 SoC and EVB support

[Tomer Maimon]

This series fixes the remaining timer binding issue and adds device tree
support for peripherals on the Nuvoton NPCM845 SoC and its Evaluation
Board (EVB).

The first patch drops the undocumented timer0 clock-names property.
The second patch reorders timer0 and PECI so the APB child nodes stay in
ascending unit-address order.
The third patch introduces peripheral nodes for Ethernet, MMC, SPI, USB,
RNG, ADC, PWM-FAN, I2C, and OP-TEE firmware in the NPCM845 SoC device
tree.
The fourth patch enables these peripherals for the NPCM845-EVB, adding
MDIO nodes, reserved memory, aliases, and board-specific configurations
such as PHY modes and SPI flash partitions.

The NPCM8XX device tree was tested on NPCM845 evaluation board.

This series depends on:
https://lore.kernel.org/all/20260610121822.2524634-2-tmaimon77@gmail.com/
https://lore.kernel.org/all/20260610121822.2524634-3-tmaimon77@gmail.com/
https://lore.kernel.org/all/20260610121822.2524634-4-tmaimon77@gmail.com/

Addressed comments from:
	- Rob Herring

Changes since version 4:
	- Split the timer0 clock-names cleanup into a separate first patch.
	- Remove nuvoton,sysgcr from udc8 and udc9.
	- Rename apb: bus@f0000000 back to apb.
	- Add no-map to tip_reserved.
	- Rename spix-mode to nuvoton,spix-mode.
	- Keep cooling-levels as 32-bit cells while encoding fan-tach-ch
	  as /bits/ 8.

Tomer Maimon (4):
  arm64: dts: nuvoton: npcm845: Drop redundant timer clock-names
  arm64: dts: nuvoton: npcm845: Reorder timer0 and PECI nodes
  arm64: dts: nuvoton: npcm845: Add peripheral nodes
  arm64: dts: nuvoton: npcm845-evb: Add peripheral nodes

 .../dts/nuvoton/nuvoton-common-npcm8xx.dtsi   | 721 +++++++++++++++++-
 .../boot/dts/nuvoton/nuvoton-npcm845-evb.dts  | 413 ++++++++++
 .../boot/dts/nuvoton/nuvoton-npcm845.dtsi     |  11 +-
 3 files changed, 1126 insertions(+), 19 deletions(-)

-- 
2.34.1

[PATCH v5 1/4] arm64: dts: nuvoton: npcm845: Drop redundant timer clock-names

[Tomer Maimon]

The NPCM845 timer0 node references a single clock, but its
clock-names property is not described by the timer binding. Drop the
undocumented name so the DTS matches the binding.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
---
 arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
index c781190b42c5..9e4fa2669f4d 100644
--- a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
@@ -73,7 +73,6 @@ timer0: timer@8000 {
 				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
 				reg = <0x8000 0x1C>;
 				clocks = <&refclk>;
-				clock-names = "refclk";
 			};
 
 			serial0: serial@0 {
-- 
2.34.1

[PATCH v5 2/4] arm64: dts: nuvoton: npcm845: Reorder timer0 and PECI nodes

[Tomer Maimon]

Move the timer0 and PECI nodes so the APB children are ordered by
ascending unit address.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
---
 .../dts/nuvoton/nuvoton-common-npcm8xx.dtsi   | 25 ++++++++++++-------
 1 file changed, 16 insertions(+), 9 deletions(-)

diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
index 9e4fa2669f4d..0e5feabf2d71 100644
--- a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
@@ -59,15 +59,6 @@ apb {
 			ranges = <0x0 0x0 0xf0000000 0x00300000>,
 				<0xfff00000 0x0 0xfff00000 0x00016000>;
 
-			peci: peci-controller@100000 {
-				compatible = "nuvoton,npcm845-peci";
-				reg = <0x100000 0x1000>;
-				interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
-				clocks = <&clk NPCM8XX_CLK_APB3>;
-				cmd-timeout-ms = <1000>;
-				status = "disabled";
-			};
-
 			timer0: timer@8000 {
 				compatible = "nuvoton,npcm845-timer";
 				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
@@ -138,6 +129,13 @@ serial6: serial@6000 {
 				status = "disabled";
 			};
 
+			timer0: timer@8000 {
+				compatible = "nuvoton,npcm845-timer";
+				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+				reg = <0x8000 0x1C>;
+				clocks = <&refclk>;
+			};
+
 			watchdog0: watchdog@801c {
 				compatible = "nuvoton,npcm845-wdt", "nuvoton,npcm750-wdt";
 				interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>;
@@ -161,6 +159,15 @@ watchdog2: watchdog@a01c {
 				status = "disabled";
 				clocks = <&refclk>;
 			};
+
+			peci: peci-controller@100000 {
+				compatible = "nuvoton,npcm845-peci";
+				reg = <0x100000 0x1000>;
+				interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM8XX_CLK_APB3>;
+				cmd-timeout-ms = <1000>;
+				status = "disabled";
+			};
 		};
 	};
 
-- 
2.34.1

[PATCH v5 3/4] arm64: dts: nuvoton: npcm845: Add peripheral nodes

[Tomer Maimon]

Extend the NPCM845 SoC DTSI with the peripheral controller nodes needed
by the evaluation board and downstream platforms. Add the Ethernet MACs,
USB device controllers and PHY, MMC controller, FIU controllers, memory
controller, RNG, ADC, PWM/FAN controller, and I2C buses. Also add the
OP-TEE firmware node needed to describe these blocks.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
---
 .../dts/nuvoton/nuvoton-common-npcm8xx.dtsi   | 695 +++++++++++++++++-
 .../boot/dts/nuvoton/nuvoton-npcm845.dtsi     |  11 +-
 2 files changed, 697 insertions(+), 9 deletions(-)

diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
index 0e5feabf2d71..7608dcf5489c 100644
--- a/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-common-npcm8xx.dtsi
@@ -4,6 +4,7 @@
 #include <dt-bindings/clock/nuvoton,npcm845-clk.h>
 #include <dt-bindings/interrupt-controller/arm-gic.h>
 #include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/gpio/gpio.h>
 
 / {
 	#address-cells = <2>;
@@ -35,6 +36,11 @@ gic: interrupt-controller@dfff9000 {
 		};
 	};
 
+	udc0_phy: usb-phy {
+		compatible = "usb-nop-xceiv";
+		#phy-cells = <0>;
+	};
+
 	ahb {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -51,6 +57,252 @@ clk: rstc: reset-controller@f0801000 {
 			#clock-cells = <1>;
 		};
 
+		gmac1: ethernet@f0804000 {
+			device_type = "network";
+			compatible = "snps,dwmac-3.72a", "snps,dwmac";
+			reg = <0x0 0xf0804000 0x0 0x2000>;
+			interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks	= <&clk NPCM8XX_CLK_AHB>;
+			clock-names = "stmmaceth";
+			pinctrl-names = "default";
+			pinctrl-0 = <&rg2_pins
+					&rg2mdio_pins>;
+			status = "disabled";
+		};
+
+		gmac2: ethernet@f0806000 {
+			device_type = "network";
+			compatible = "snps,dwmac-3.72a", "snps,dwmac";
+			reg = <0x0 0xf0806000 0x0 0x2000>;
+			interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks	= <&clk NPCM8XX_CLK_AHB>;
+			clock-names = "stmmaceth";
+			pinctrl-names = "default";
+			pinctrl-0 = <&r1_pins
+					&r1err_pins
+					&r1md_pins>;
+			status = "disabled";
+		};
+
+		gmac3: ethernet@f0808000 {
+			device_type = "network";
+			compatible = "snps,dwmac-3.72a", "snps,dwmac";
+			reg = <0x0 0xf0808000 0x0 0x2000>;
+			interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "macirq";
+			clocks	= <&clk NPCM8XX_CLK_AHB>;
+			clock-names = "stmmaceth";
+			pinctrl-names = "default";
+			pinctrl-0 = <&r2_pins
+					&r2err_pins
+					&r2md_pins>;
+			status = "disabled";
+		};
+
+		mc: memory-controller@f0824000 {
+			compatible = "nuvoton,npcm845-memory-controller";
+			reg = <0x0 0xf0824000 0x0 0x1000>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		udc0: usb@f0830000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0830000 0x0 0x1000
+			       0x0 0xfffeb000 0x0 0x800>;
+			interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc1: usb@f0831000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0831000 0x0 0x1000
+			       0x0 0xfffeb800 0x0 0x800>;
+			interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc2: usb@f0832000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0832000 0x0 0x1000
+			       0x0 0xfffec000 0x0 0x800>;
+			interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc3: usb@f0833000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0833000 0x0 0x1000
+			       0x0 0xfffec800 0x0 0x800>;
+			interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc4: usb@f0834000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0834000 0x0 0x1000
+			       0x0 0xfffed000 0x0 0x800>;
+			interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc5: usb@f0835000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0835000 0x0 0x1000
+			       0x0 0xfffed800 0x0 0x800>;
+			interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc6: usb@f0836000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0836000 0x0 0x1000
+			       0x0 0xfffee000 0x0 0x800>;
+			interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc7: usb@f0837000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0837000 0x0 0x1000
+			       0x0 0xfffee800 0x0 0x800>;
+			interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc8: usb@f0838000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0838000 0x0 0x1000
+			       0x0 0xfffef000 0x0 0x800>;
+			interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		udc9: usb@f0839000 {
+			compatible = "nuvoton,npcm845-udc", "nuvoton,npcm750-udc";
+			reg = <0x0 0xf0839000 0x0 0x1000
+			       0x0 0xfffef800 0x0 0x800>;
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_SU>;
+			clock-names = "clk_usb_bridge";
+
+			phys = <&udc0_phy>;
+			phy_type = "utmi_wide";
+			dr_mode = "peripheral";
+			status = "disabled";
+		};
+
+		sdhci: mmc@f0842000 {
+			compatible = "nuvoton,npcm845-sdhci";
+			reg = <0x0 0xf0842000 0x0 0x100>;
+			interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk NPCM8XX_CLK_AHB>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc8_pins
+				     &mmc_pins>;
+			status = "disabled";
+		};
+
+		fiu0: spi@fb000000 {
+			compatible = "nuvoton,npcm845-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0xfb000000 0x0 0x1000>;
+			reg-names = "control";
+			clocks =  <&clk NPCM8XX_CLK_SPI0>;
+			status = "disabled";
+		};
+
+		fiu1: spi@fb002000 {
+			compatible = "nuvoton,npcm845-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0xfb002000 0x0 0x1000>;
+			reg-names = "control";
+			clocks =  <&clk NPCM8XX_CLK_SPI1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi1_pins>;
+			status = "disabled";
+		};
+
+		fiu3: spi@c0000000 {
+			compatible = "nuvoton,npcm845-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0xc0000000 0x0 0x1000>;
+			reg-names = "control";
+			clocks =  <&clk NPCM8XX_CLK_SPI3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&spi3_pins>;
+			status = "disabled";
+		};
+
+		fiux: spi@fb001000 {
+			compatible = "nuvoton,npcm845-fiu";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x0 0xfb001000 0x0 0x1000>,
+			<0x0 0xf8000000 0x0 0x2000000>;
+			reg-names = "control", "memory";
+			clocks =  <&clk NPCM8XX_CLK_SPIX>;
+			status = "disabled";
+		};
+
 		apb {
 			#address-cells = <1>;
 			#size-cells = <1>;
@@ -59,13 +311,6 @@ apb {
 			ranges = <0x0 0x0 0xf0000000 0x00300000>,
 				<0xfff00000 0x0 0xfff00000 0x00016000>;
 
-			timer0: timer@8000 {
-				compatible = "nuvoton,npcm845-timer";
-				interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-				reg = <0x8000 0x1C>;
-				clocks = <&refclk>;
-			};
-
 			serial0: serial@0 {
 				compatible = "nuvoton,npcm845-uart", "nuvoton,npcm750-uart";
 				reg = <0x0 0x1000>;
@@ -168,6 +413,442 @@ peci: peci-controller@100000 {
 				cmd-timeout-ms = <1000>;
 				status = "disabled";
 			};
+
+			rng: rng@b000 {
+				compatible = "nuvoton,npcm845-rng";
+				reg = <0xb000 0x8>;
+				status = "disabled";
+			};
+
+			adc: adc@c000 {
+				compatible = "nuvoton,npcm845-adc";
+				reg = <0xC000 0x8>;
+				interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+				clocks = <&clk NPCM8XX_CLK_ADC>;
+				resets = <&rstc 0x20 27>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@80000 {
+				reg = <0x80000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb0_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@81000 {
+				reg = <0x81000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb1_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c2: i2c@82000 {
+				reg = <0x82000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb2_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c3: i2c@83000 {
+				reg = <0x83000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb3_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c4: i2c@84000 {
+				reg = <0x84000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb4_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c5: i2c@85000 {
+				reg = <0x85000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb5_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c6: i2c@86000 {
+				reg = <0x86000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb6_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c7: i2c@87000 {
+				reg = <0x87000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb7_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c8: i2c@88000 {
+				reg = <0x88000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb8_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c9: i2c@89000 {
+				reg = <0x89000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb9_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c10: i2c@8a000 {
+				reg = <0x8a000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb10_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c11: i2c@8b000 {
+				reg = <0x8b000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb11_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c12: i2c@8c000 {
+				reg = <0x8c000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb12_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c13: i2c@8d000 {
+				reg = <0x8d000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb13_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c14: i2c@8e000 {
+				reg = <0x8e000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb14_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c15: i2c@8f000 {
+				reg = <0x8f000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb15_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c16: i2c@fff00000 {
+				reg = <0xfff00000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb16_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c17: i2c@fff01000 {
+				reg = <0xfff01000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb17_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c18: i2c@fff02000 {
+				reg = <0xfff02000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb18_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c19: i2c@fff03000 {
+				reg = <0xfff03000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb19_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c20: i2c@fff04000 {
+				reg = <0xfff04000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb20_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c21: i2c@fff05000 {
+				reg = <0xfff05000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb21_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c22: i2c@fff06000 {
+				reg = <0xfff06000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb22_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c23: i2c@fff07000 {
+				reg = <0xfff07000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&smb23_pins>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c24: i2c@fff08000 {
+				reg = <0xfff08000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 152 IRQ_TYPE_LEVEL_HIGH>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c25: i2c@fff09000 {
+				reg = <0xfff09000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			i2c26: i2c@fff0a000 {
+				reg = <0xfff0a000 0x1000>;
+				compatible = "nuvoton,npcm845-i2c";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks =  <&clk NPCM8XX_CLK_APB2>;
+				clock-frequency = <100000>;
+				interrupts = <GIC_SPI 154 IRQ_TYPE_LEVEL_HIGH>;
+				nuvoton,sys-mgr = <&gcr>;
+				status = "disabled";
+			};
+
+			pwm_fan:pwm-fan-controller@103000 {
+				compatible = "nuvoton,npcm845-pwm-fan";
+				reg = <0x103000 0x3000>,
+					<0x180000 0x8000>;
+				reg-names = "pwm", "fan";
+				clocks =  <&clk NPCM8XX_CLK_APB3>,
+					<&clk NPCM8XX_CLK_APB4>;
+				clock-names = "pwm","fan";
+				interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+						<GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pwm0_pins &pwm1_pins
+						&pwm2_pins &pwm3_pins
+						&pwm4_pins &pwm5_pins
+						&pwm6_pins &pwm7_pins
+						&pwm8_pins &pwm9_pins
+						&pwm10_pins &pwm11_pins
+						&fanin0_pins &fanin1_pins
+						&fanin2_pins &fanin3_pins
+						&fanin4_pins &fanin5_pins
+						&fanin6_pins &fanin7_pins
+						&fanin8_pins &fanin9_pins
+						&fanin10_pins &fanin11_pins
+						&fanin12_pins &fanin13_pins
+						&fanin14_pins &fanin15_pins>;
+				status = "disabled";
+			};
+
+			pspi: spi@201000 {
+				compatible = "nuvoton,npcm845-pspi";
+				reg = <0x201000 0x1000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pspi_pins>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+				clocks =  <&clk NPCM8XX_CLK_APB5>;
+				clock-names = "clk_apb5";
+				resets = <&rstc 0x24 23>;
+				status = "disabled";
+			};
+
 		};
 	};
 
diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845.dtsi b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845.dtsi
index 8239d9a9f0d2..21dea323612d 100644
--- a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845.dtsi
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845.dtsi
@@ -64,8 +64,8 @@ arm-pmu {
 	};
 
 	psci {
-		compatible = "arm,psci-1.0";
-		method = "smc";
+		compatible      = "arm,psci-1.0";
+		method          = "smc";
 	};
 
 	timer {
@@ -75,4 +75,11 @@ timer {
 			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
 			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
 	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
 };
-- 
2.34.1

[PATCH v5 4/4] arm64: dts: nuvoton: npcm845-evb: Add peripheral nodes

[Tomer Maimon]

Enable peripheral support for the NPCM845 evaluation board by wiring up
the SoC controller nodes to the board design. Add board aliases,
GPIO-backed MDIO buses for the external PHYs, a reserved-memory region
for TIP firmware, and flash partitions for the FIU boot flash. Enable
the Ethernet MACs, MMC controller, FIU controllers, USB device
controllers, ADC, RNG, PWM/FAN controller, I2C buses, and PECI
interface with the board-specific pinctrl and PHY connections they
require.

Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
---
 .../boot/dts/nuvoton/nuvoton-npcm845-evb.dts  | 413 ++++++++++++++++++
 1 file changed, 413 insertions(+)

diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts
index 5edf5d13342d..28dbb865d739 100644
--- a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts
+++ b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts
@@ -10,6 +10,42 @@ / {
 
 	aliases {
 		serial0 = &serial0;
+		ethernet1 = &gmac1;
+		ethernet2 = &gmac2;
+		ethernet3 = &gmac3;
+		mdio-gpio0 = &mdio0;
+		mdio-gpio1 = &mdio1;
+		fiu0 = &fiu0;
+		fiu1 = &fiu3;
+		fiu2 = &fiux;
+		fiu3 = &fiu1;
+		i2c0 = &i2c0;
+		i2c1 = &i2c1;
+		i2c2 = &i2c2;
+		i2c3 = &i2c3;
+		i2c4 = &i2c4;
+		i2c5 = &i2c5;
+		i2c6 = &i2c6;
+		i2c7 = &i2c7;
+		i2c8 = &i2c8;
+		i2c9 = &i2c9;
+		i2c10 = &i2c10;
+		i2c11 = &i2c11;
+		i2c12 = &i2c12;
+		i2c13 = &i2c13;
+		i2c14 = &i2c14;
+		i2c15 = &i2c15;
+		i2c16 = &i2c16;
+		i2c17 = &i2c17;
+		i2c18 = &i2c18;
+		i2c19 = &i2c19;
+		i2c20 = &i2c20;
+		i2c21 = &i2c21;
+		i2c22 = &i2c22;
+		i2c23 = &i2c23;
+		i2c24 = &i2c24;
+		i2c25 = &i2c25;
+		i2c26 = &i2c26;
 	};
 
 	chosen {
@@ -26,12 +62,389 @@ refclk: refclk-25mhz {
 		clock-frequency = <25000000>;
 		#clock-cells = <0>;
 	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		tip_reserved: tip@0 {
+			reg = <0x0 0x0 0x0 0x6200000>;
+		};
+	};
+
+	mdio0: mdio-0 {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpio1 25 GPIO_ACTIVE_HIGH>,
+			<&gpio1 26 GPIO_ACTIVE_HIGH>;
+
+		phy0: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+
+	mdio1: mdio-1 {
+		compatible = "virtual,mdio-gpio";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>,
+			<&gpio2 28 GPIO_ACTIVE_HIGH>;
+
+		phy1: ethernet-phy@0 {
+			reg = <0>;
+		};
+	};
+};
+
+&gmac1 {
+	phy-mode = "rgmii-id";
+	snps,eee-force-disable;
+	status = "okay";
+};
+
+&gmac2 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&r1_pins
+			&r1oen_pins>;
+	phy-handle = <&phy0>;
+	status = "okay";
+};
+
+&gmac3 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&r2_pins
+			&r2oen_pins>;
+	phy-handle = <&phy1>;
+	status = "okay";
 };
 
 &serial0 {
 	status = "okay";
 };
 
+&fiu0 {
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-rx-bus-width = <1>;
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			bmc@0 {
+				label = "bmc";
+				reg = <0x00000000 0x04000000>;
+			};
+			u-boot@0 {
+				label = "u-boot";
+				reg = <0x00000000 0x007C0000>;
+			};
+			u-boot-env@7c0000 {
+				label = "u-boot-env";
+				reg = <0x007C0000 0x00040000>;
+			};
+			kernel@800000 {
+				label = "kernel";
+				reg = <0x00800000 0x00800000>;
+			};
+			rofs@1000000 {
+				label = "rofs";
+				reg = <0x01000000 0x02C00000>;
+			};
+			rwfs@3c00000 {
+				label = "rwfs";
+				reg = <0x03C00000 0x00400000>;
+			};
+		};
+	};
+};
+
+&fiu1 {
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-rx-bus-width = <2>;
+		spi-tx-bus-width = <2>;
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				label = "spi1-system1";
+				reg = <0x0 0x0>;
+			};
+		};
+	};
+};
+
+&fiu3 {
+	pinctrl-0 = <&spi3_pins>, <&spi3quad_pins>;
+	status = "okay";
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-rx-bus-width = <1>;
+		reg = <0>;
+		spi-max-frequency = <5000000>;
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			partition@0 {
+				label = "spi3-system1";
+				reg = <0x0 0x0>;
+			};
+		};
+	};
+};
+
+&fiux {
+	nuvoton,spix-mode;
+};
+
+&sdhci {
+	status = "okay";
+};
+
+&udc0 {
+	status = "okay";
+};
+
+&udc1 {
+	status = "okay";
+};
+
+&udc2 {
+	status = "okay";
+};
+
+&udc3 {
+	status = "okay";
+};
+
+&udc4 {
+	status = "okay";
+};
+
+&udc5 {
+	status = "okay";
+};
+
+&udc6 {
+	status = "okay";
+};
+
+&udc7 {
+	status = "okay";
+};
+
+&mc {
+	status = "okay";
+};
+
+&peci {
+	status = "okay";
+};
+
+&rng {
+	status = "okay";
+};
+
+&adc {
+	#io-channel-cells = <1>;
+	status = "okay";
+};
+
 &watchdog1 {
 	status = "okay";
 };
+
+&pwm_fan {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&pwm0_pins &pwm1_pins
+		&pwm2_pins &pwm3_pins
+		&pwm4_pins &pwm5_pins
+		&pwm6_pins &pwm7_pins
+		&fanin0_pins &fanin1_pins
+		&fanin2_pins &fanin3_pins
+		&fanin4_pins &fanin5_pins
+		&fanin6_pins &fanin7_pins>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	fan@0 {
+		reg = <0x00>;
+		fan-tach-ch = /bits/ 8 <0x0 0x1>;
+		cooling-levels = <127 255>;
+	};
+	fan@1 {
+		reg = <0x01>;
+		fan-tach-ch = /bits/ 8 <0x2 0x3>;
+		cooling-levels = <127 255>;
+	};
+	fan@2 {
+		reg = <0x02>;
+		fan-tach-ch = /bits/ 8 <0x4 0x5>;
+		cooling-levels = <127 255>;
+	};
+	fan@3 {
+		reg = <0x03>;
+		fan-tach-ch = /bits/ 8 <0x6 0x7>;
+		cooling-levels = <127 255>;
+	};
+	fan@4 {
+		reg = <0x04>;
+		fan-tach-ch = /bits/ 8 <0x8 0x9>;
+		cooling-levels = <127 255>;
+	};
+	fan@5 {
+		reg = <0x05>;
+		fan-tach-ch = /bits/ 8 <0xa 0xb>;
+		cooling-levels = <127 255>;
+	};
+	fan@6 {
+		reg = <0x06>;
+		fan-tach-ch = /bits/ 8 <0xc 0xd>;
+		cooling-levels = <127 255>;
+	};
+	fan@7 {
+		reg = <0x07>;
+		fan-tach-ch = /bits/ 8 <0xe 0xf>;
+		cooling-levels = <127 255>;
+	};
+};
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	eeprom@50 {
+		compatible = "atmel,24c256";
+		reg = <0x50>;
+	};
+};
+
+&i2c2 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	ipmb@10 {
+		compatible = "ipmb-dev";
+		reg = <0x10>;
+		i2c-protocol;
+	};
+};
+
+&i2c3 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	ipmb@11 {
+		compatible = "ipmb-dev";
+		reg = <0x11>;
+		i2c-protocol;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&i2c6 {
+	status = "okay";
+};
+
+&i2c7 {
+	status = "okay";
+};
+
+&i2c8 {
+	status = "okay";
+};
+
+&i2c9 {
+	status = "okay";
+};
+
+&i2c10 {
+	status = "okay";
+};
+
+&i2c11 {
+	status = "okay";
+};
+
+&i2c12 {
+	status = "okay";
+};
+
+&i2c13 {
+	status = "okay";
+};
+
+&i2c14 {
+	status = "okay";
+};
+
+&i2c15 {
+	status = "okay";
+};
+
+&i2c16 {
+	status = "okay";
+};
+
+&i2c17 {
+	status = "okay";
+};
+
+&i2c18 {
+	status = "okay";
+};
+
+&i2c19 {
+	status = "okay";
+};
+
+&i2c20 {
+	status = "okay";
+};
+
+&i2c21 {
+	status = "okay";
+};
+
+&i2c22 {
+	status = "okay";
+};
+
+&i2c23 {
+	status = "okay";
+};
+
+&i2c24 {
+	status = "okay";
+};
+
+&i2c25 {
+	status = "okay";
+};
+
+&i2c26 {
+	status = "okay";
+};
-- 
2.34.1

Re: [PATCH v5 4/4] arm64: dts: nuvoton: npcm845-evb: Add peripheral nodes

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 5 potential issue(s) to consider:
- [High] The reserved memory region 'tip_reserved' for the TIP firmware lacks the 'no-map' property, which will cause memory corruption or speculative access crashes.
- [High] The `cooling-levels` property in the `&pwm_fan` sub-nodes is configured as a standard 32-bit integer array (`<127 255>`) instead of an 8-bit integer array (`/bits/ 8 <127 255>`).
- [Medium] Aliases 'fiu1' and 'fiu3' are cross-assigned to '&fiu3' and '&fiu1', contradicting their fixed-partition labels.
- [Low] The property 'snps,eee-force-disable' is undocumented and is not parsed by any kernel driver.
- [Low] Duplicate unit-address in `fiu0` flash partitions.
--

commit 157ec4fb1bc26d1a937aeb0fed0b00add10a7c95
Author: Tomer Maimon <tmaimon77@gmail.com>

arm64: dts: nuvoton: npcm845-evb: Add peripheral nodes

Enable peripheral support for the NPCM845 evaluation board by wiring up
the SoC controller nodes to the board design. Add board aliases, GPIO-backed
MDIO buses, reserved memory, flash partitions, and various controllers.

> diff --git a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts
> index 5edf5d13342da..28dbb865d739d 100644
> --- a/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts
> +++ b/arch/arm64/boot/dts/nuvoton/nuvoton-npcm845-evb.dts
> @@ -10,6 +10,42 @@ / {
>  
>  	aliases {
>  		serial0 = &serial0;
> +		ethernet1 = &gmac1;
[ ... ]
> +		mdio-gpio1 = &mdio1;
> +		fiu0 = &fiu0;
> +		fiu1 = &fiu3;
> +		fiu2 = &fiux;
> +		fiu3 = &fiu1;

[Severity: Medium]
Does this alias mapping intentionally cross-assign fiu1 to &fiu3 and fiu3 to
&fiu1?

Looking further down in the patch, the partition under &fiu1 is explicitly
labeled spi1-system1, and the partition under &fiu3 is labeled spi3-system1.
This swap could cause user-space confusion by mapping /dev/mtd1 to a partition
labeled spi3-system1 and /dev/mtd3 to a partition labeled spi1-system1.

[ ... ]
> +	reserved-memory {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		ranges;
> +
> +		tip_reserved: tip@0 {
> +			reg = <0x0 0x0 0x0 0x6200000>;
> +		};
> +	};

[Severity: High]
Without the no-map property, will the kernel map this 98MB reserved memory
region into the standard linear mapping with cacheable attributes?

Since this memory belongs to the TIP coprocessor, the ARM64 CPU might
aggressively perform speculative instruction prefetches and data loads here.
Could this lead to corrupted non-coherent working state via cache line
evictions, or trigger fatal asynchronous SErrors and synchronous external
aborts if the memory is hardware-protected by TrustZone?

[ ... ]
> +&gmac1 {
> +	phy-mode = "rgmii-id";
> +	snps,eee-force-disable;
> +	status = "okay";
> +};

[Severity: Low]
Is the snps,eee-force-disable property supported? It does not appear in the
snps,dwmac DT binding schema and seems to be ignored by the stmmac driver.
This appears to be a dead configuration that triggers a dt-schema violation.

[ ... ]
> +&fiu0 {
> +	status = "okay";
> +	flash@0 {
> +		compatible = "jedec,spi-nor";
> +		spi-rx-bus-width = <1>;
> +		reg = <0>;
> +		spi-max-frequency = <5000000>;
> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +			bmc@0 {
> +				label = "bmc";
> +				reg = <0x00000000 0x04000000>;
> +			};
> +			u-boot@0 {
> +				label = "u-boot";
> +				reg = <0x00000000 0x007C0000>;
> +			};

[Severity: Low]
Both the bmc and u-boot partitions are using the @0 unit-address. Does this
result in a duplicate unit-address warning from the devicetree compiler?

[ ... ]
> +&pwm_fan {
> +	status = "okay";
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pwm0_pins &pwm1_pins
[ ... ]
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	fan@0 {
> +		reg = <0x00>;
> +		fan-tach-ch = /bits/ 8 <0x0 0x1>;
> +		cooling-levels = <127 255>;
> +	};

[Severity: High]
Should the cooling-levels property be configured as an 8-bit array, matching
the fan-tach-ch format, such as /bits/ 8 <127 255>?

The Nuvoton PWM fan driver parses this property using
of_property_read_u8_array() and of_property_count_u8_elems().

Since the DT property is authored as two 32-bit big-endian integers, it
consumes 8 bytes total. The driver might incorrectly count 8 elements and
parse them as an array of [0, 0, 0, 127, 0, 0, 0, 255].

Could this corrupt the thermal control map and shut the fans off completely
at intermediate or critical temperatures?

[ ... ]

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260615142548.1373799-1-tmaimon77@gmail.com?part=4