* [PATCH 2/3] arm64: dts: qcom: Add HP EliteBook X G2q 14 AI
2026-06-21 4:50 [PATCH 0/3] X2 Elite HP EliteBook X G2q support Jason Pettit
2026-06-21 4:50 ` [PATCH 1/3] dt-bindings: arm: qcom: Add HP EliteBook X G2q 14 AI Jason Pettit
@ 2026-06-21 4:50 ` Jason Pettit
2026-06-21 5:08 ` sashiko-bot
2026-06-21 4:50 ` [PATCH 3/3] firmware: qcom: scm: Allow QSEECOM on " Jason Pettit
2 siblings, 1 reply; 5+ messages in thread
From: Jason Pettit @ 2026-06-21 4:50 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Akhil P Oommen,
Mahadevan P, Sibi Sankar, Jingyi Wang, Ananthu C V, Jason Pettit
Add board support for the HP EliteBook X G2q 14" Next Gen AI PC
(product SKU C4JG0AV, board 8E91), a Snapdragon X2 Elite (Glymur)
laptop, using the "hp,elitebook-x-g2q" / "qcom,glymur" compatible.
Enabled by this device tree:
- internal eDP panel (samsung,atna33xc20)
- 2x USB Type-C with DisplayPort alt-mode and USB
- chassis HDMI output
- chassis USB-A host port (usb_mp multiport controller)
- internal eUSB2 host with the Elan fingerprint reader
- NVMe SSD on PCIe5
- Wi-Fi and Bluetooth
- HID-over-I2C keyboard, touchpad, touchscreen; lid switch
- Adreno GPU and GMU (Freedreno GL on Mesa)
- audio playback and capture
The HDMI jack is driven by a power-only DisplayPort-to-HDMI LSPCON on
the usb_2 combo-PHY DP lanes rather than being a third USB-C port; HPD
is on gpio126. The LSPCON is on an I/O sub-board with no I2C/AUX control
path, so it is modelled with the generic simple-bridge "parade,ps185hdm"
compatible used by the in-tree x1e80100 HDMI-bridge boards (the exact
bridge part is unconfirmed) and it needs CONFIG_DRM_SIMPLE_BRIDGE.
The &gpu/&gmu enable, the audio nodes and &remoteproc_soccp opt into
glymur.dtsi SoC nodes that are still in-flight; those series are
declared as prerequisites in the cover letter.
Signed-off-by: Jason Pettit <jason.pettit@oss.qualcomm.com>
Assisted-by: Claude:claude-opus-4-8
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts | 977 +++++++++++++++++++++
2 files changed, 978 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 6f33c4e2f09c..b10629808b76 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -16,6 +16,7 @@ dtb-$(CONFIG_ARCH_QCOM) += apq8096sg-db820c.dtb
dtb-$(CONFIG_ARCH_QCOM) += apq8096-ifc6640.dtb
dtb-$(CONFIG_ARCH_QCOM) += eliza-mtp.dtb
dtb-$(CONFIG_ARCH_QCOM) += glymur-crd.dtb
+dtb-$(CONFIG_ARCH_QCOM) += glymur-hp-elitebook-x-g2q.dtb
dtb-$(CONFIG_ARCH_QCOM) += hamoa-iot-evk.dtb
hamoa-iot-evk-el2-dtbs := hamoa-iot-evk.dtb x1-el2.dtbo
diff --git a/arch/arm64/boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts b/arch/arm64/boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts
new file mode 100644
index 000000000000..795940a99946
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/glymur-hp-elitebook-x-g2q.dts
@@ -0,0 +1,977 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+/dts-v1/;
+
+#include "glymur.dtsi"
+
+#include "pmcx0102.dtsi" /* SPMI0: SID-2/3 SPMI1: SID-2/3 */
+#include "pmh0101.dtsi" /* SPMI0: SID-1 */
+#include "pmh0110-glymur.dtsi" /* SPMI0: SID-5/7 SPMI1: SID-5 */
+#include "pmh0104-glymur.dtsi" /* SPMI0: SID-8/9 SPMI1: SID-11 */
+#include "pmk8850.dtsi" /* SPMI0: SID-0 */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
+
+/ {
+ model = "HP EliteBook X G2q 14 AI";
+ compatible = "hp,elitebook-x-g2q", "qcom,glymur";
+
+ aliases {
+ serial1 = &uart14;
+ };
+
+ clocks {
+ xo_board: xo-board {
+ compatible = "fixed-clock";
+ clock-frequency = <38400000>;
+ #clock-cells = <0>;
+ };
+
+ sleep_clk: sleep-clk {
+ compatible = "fixed-clock";
+ clock-frequency = <32000>;
+ #clock-cells = <0>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&lid_default>;
+ pinctrl-names = "default";
+
+ switch-lid {
+ label = "lid";
+ gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+ linux,input-type = <EV_SW>;
+ linux,code = <SW_LID>;
+ wakeup-source;
+ wakeup-event-action = <EV_ACT_DEASSERTED>;
+ };
+ };
+
+ hdmi-bridge {
+ compatible = "parade,ps185hdm";
+
+ pinctrl-0 = <&usb2_dp_hot_plug_detect>;
+ pinctrl-names = "default";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi_bridge_in: endpoint {
+ remote-endpoint = <&usb_2_qmpphy_out_dp>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ hdmi_bridge_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+
+ hdmi-connector {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&hdmi_bridge_out>;
+ };
+ };
+ };
+
+ pmic-glink {
+ compatible = "qcom,glymur-pmic-glink",
+ "qcom,pmic-glink";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Left side display-adjacent port */
+ connector@0 {
+ compatible = "usb-c-connector";
+ reg = <0>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_0_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&usb_0_qmpphy_out>;
+ };
+ };
+ };
+ };
+
+ /* Left side user-adjacent port */
+ connector@1 {
+ compatible = "usb-c-connector";
+ reg = <1>;
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in1: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in1: endpoint {
+ remote-endpoint = <&usb_1_qmpphy_out>;
+ };
+ };
+ };
+ };
+ };
+
+ vreg_edp_3p3: regulator-edp-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_EDP_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&edp_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_nvme: regulator-nvme {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_NVME_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmh0101_gpios 14 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&nvme_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_wcn_0p95: regulator-wcn-0p95 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_0P95";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <950000>;
+
+ vin-supply = <&vreg_wcn_3p3>;
+ };
+
+ vreg_wcn_3p3: regulator-wcn-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_WCN_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 94 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&wcn_sw_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ sound {
+ compatible = "qcom,glymur-sndcard";
+ model = "GLYMUR-HP-EliteBook-X-G2q";
+
+ audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT",
+ "TweeterLeft IN", "WSA WSA_SPK2 OUT",
+ "WooferRight IN", "WSA2 WSA_SPK1 OUT",
+ "TweeterRight IN", "WSA2 WSA_SPK2 OUT",
+ "VA DMIC0", "vdd-micb",
+ "VA DMIC1", "vdd-micb",
+ "VA DMIC2", "vdd-micb",
+ "VA DMIC3", "vdd-micb";
+
+ va-dai-link {
+ link-name = "VA Capture";
+
+ codec {
+ sound-dai = <&lpass_vamacro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wsa-dai-link {
+ link-name = "WSA Playback";
+
+ codec {
+ sound-dai = <&left_woofer>, <&left_tweeter>,
+ <&swr0 0>, <&lpass_wsamacro 0>,
+ <&right_woofer>, <&right_tweeter>,
+ <&swr3 0>, <&lpass_wsa2macro 0>;
+ };
+
+ cpu {
+ sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+ };
+
+ wcn7850-pmu {
+ compatible = "qcom,wcn7850-pmu";
+
+ vdd-supply = <&vreg_wcn_0p95>;
+ vddio-supply = <&vreg_l15b_e0_1p8>;
+ vddaon-supply = <&vreg_l15b_e0_1p8>;
+ vdddig-supply = <&vreg_l15b_e0_1p8>;
+ vddrfa1p2-supply = <&vreg_l15b_e0_1p8>;
+ vddrfa1p8-supply = <&vreg_l15b_e0_1p8>;
+
+ wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+ bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+ pinctrl-0 = <&wcn_wlan_bt_en>;
+ pinctrl-names = "default";
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p8: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p8";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pmh0101-rpmh-regulators";
+ qcom,pmic-id = "B_E0";
+
+ vreg_l1b_e0_1p8: ldo1 {
+ regulator-name = "vreg_l1b_e0_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_e0_1p8: ldo15 {
+ regulator-name = "vreg_l15b_e0_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l18b_e0_1p2: ldo18 {
+ regulator-name = "vreg_l18b_e0_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pmcx0102-rpmh-regulators";
+ qcom,pmic-id = "C_E1";
+
+ vreg_l1c_e1_0p91: ldo1 {
+ regulator-name = "vreg_l1c_e1_0p91";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pmh0110-rpmh-regulators";
+ qcom,pmic-id = "F_E0";
+
+ vreg_l2f_e0_0p94: ldo2 {
+ regulator-name = "vreg_l2f_e0_0p94";
+ regulator-min-microvolt = <936000>;
+ regulator-max-microvolt = <936000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3f_e0_0p91: ldo3 {
+ regulator-name = "vreg_l3f_e0_0p91";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-3 {
+ compatible = "qcom,pmh0110-rpmh-regulators";
+ qcom,pmic-id = "F_E1";
+
+ vreg_l2f_e1_0p88: ldo2 {
+ regulator-name = "vreg_l2f_e1_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4f_e1_1p2: ldo4 {
+ regulator-name = "vreg_l4f_e1_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-4 {
+ compatible = "qcom,pmh0110-rpmh-regulators";
+ qcom,pmic-id = "H_E0";
+
+ vreg_l1h_e0_0p94: ldo1 {
+ regulator-name = "vreg_l1h_e0_0p94";
+ regulator-min-microvolt = <936000>;
+ regulator-max-microvolt = <936000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2h_e0_0p88: ldo2 {
+ regulator-name = "vreg_l2h_e0_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l4h_e0_1p2: ldo4 {
+ regulator-name = "vreg_l4h_e0_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&gmu {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ keyboard@3a {
+ compatible = "hid-over-i2c";
+ reg = <0x3a>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-0 = <&kybd_default>;
+ pinctrl-names = "default";
+
+ wakeup-source;
+ };
+
+ touchpad@2c {
+ compatible = "hid-over-i2c";
+ reg = <0x2c>;
+
+ hid-descr-addr = <0x20>;
+ interrupts-extended = <&tlmm 66 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-0 = <&tpad_default>;
+ pinctrl-names = "default";
+
+ wakeup-source;
+ };
+};
+
+&i2c8 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ touchscreen@10 {
+ compatible = "hid-over-i2c";
+ reg = <0x10>;
+
+ hid-descr-addr = <0x1>;
+ interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+ post-power-on-delay-ms = <200>;
+
+ pinctrl-0 = <&ts0_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&lpass_vamacro {
+ vdd-micb-supply = <&vreg_l1b_e0_1p8>;
+
+ pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+ pinctrl-names = "default";
+
+ qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp1 {
+ status = "okay";
+};
+
+&mdss_dp1_out {
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp2 {
+ status = "okay";
+};
+
+&mdss_dp2_out {
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+ /delete-property/ #sound-dai-cells;
+
+ status = "okay";
+
+ aux-bus {
+ panel {
+ compatible = "samsung,atna33xc20";
+ enable-gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+ power-supply = <&vreg_edp_3p3>;
+
+ pinctrl-0 = <&edp_bl_en>;
+ pinctrl-names = "default";
+
+ port {
+ edp_panel_in: endpoint {
+ remote-endpoint = <&mdss_dp3_out>;
+ };
+ };
+ };
+ };
+};
+
+&mdss_dp3_out {
+ data-lanes = <0 1 2 3>;
+ link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+ remote-endpoint = <&edp_panel_in>;
+};
+
+&mdss_dp3_phy {
+ vdda-phy-supply = <&vreg_l2f_e1_0p88>;
+ vdda-pll-supply = <&vreg_l4f_e1_1p2>;
+
+ status = "okay";
+};
+
+&pcie4 {
+ pinctrl-0 = <&pcie4_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie4_phy {
+ vdda-phy-supply = <&vreg_l1c_e1_0p91>;
+ vdda-pll-supply = <&vreg_l4f_e1_1p2>;
+
+ status = "okay";
+};
+
+&pcie4_port0 {
+ reset-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+ wifi@0 {
+ compatible = "pci17cb,1107";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+ };
+};
+
+&pcie5 {
+ vddpe-3v3-supply = <&vreg_nvme>;
+
+ pinctrl-0 = <&pcie5_default>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie5_phy {
+ vdda-phy-supply = <&vreg_l2f_e0_0p94>;
+ vdda-pll-supply = <&vreg_l4h_e0_1p2>;
+
+ status = "okay";
+};
+
+&pcie5_port0 {
+ reset-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+ status = "okay";
+};
+
+&pmh0101_gpios {
+ nvme_reg_en: nvme-reg-en-state {
+ pins = "gpio14";
+ function = "normal";
+ bias-disable;
+ };
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/glymur/hp/elitebook-x-g2q/adsp.mbn",
+ "qcom/glymur/hp/elitebook-x-g2q/adsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_soccp {
+ status = "okay";
+};
+
+&swr0 {
+ status = "okay";
+
+ /* WSA8845, left woofer */
+ left_woofer: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "WooferLeft";
+ vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+ vdd-io-supply = <&vreg_l18b_e0_1p2>;
+ qcom,port-mapping = <1 2 3 7 12 14>;
+ };
+
+ /* WSA8845, left tweeter */
+ left_tweeter: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TweeterLeft";
+ vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+ vdd-io-supply = <&vreg_l18b_e0_1p2>;
+ qcom,port-mapping = <4 5 6 7 13 15>;
+ };
+};
+
+&swr3 {
+ status = "okay";
+
+ /* WSA8845, right woofer */
+ right_woofer: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "WooferRight";
+ vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+ vdd-io-supply = <&vreg_l18b_e0_1p2>;
+ qcom,port-mapping = <1 2 3 7 12 14>;
+ };
+
+ /* WSA8845, right tweeter */
+ right_tweeter: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "TweeterRight";
+ vdd-1p8-supply = <&vreg_l15b_e0_1p8>;
+ vdd-io-supply = <&vreg_l18b_e0_1p2>;
+ qcom,port-mapping = <4 5 6 7 13 15>;
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <4 4>, /* EC TZ Secure I3C */
+ <10 2>, /* OOB UART */
+ <44 4>, /* Security SPI (TPM) */
+ <65 1>; /* EC reset */
+
+ edp_bl_en: edp-bl-en-state {
+ pins = "gpio18";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ ts0_default: ts0-default-state {
+ pins = "gpio51";
+ function = "gpio";
+ bias-disable;
+ };
+
+ tpad_default: tpad-default-state {
+ pins = "gpio66";
+ function = "gpio";
+ bias-disable;
+ };
+
+ kybd_default: kybd-default-state {
+ pins = "gpio67";
+ function = "gpio";
+ bias-disable;
+ };
+
+ edp_reg_en: edp-reg-en-state {
+ pins = "gpio70";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ lid_default: lid-default-state {
+ pins = "gpio92";
+ function = "gpio";
+ bias-disable;
+ };
+
+ wcn_sw_en: wcn-sw-en-state {
+ pins = "gpio94";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wcn_wlan_bt_en: wcn-wlan-bt-en-state {
+ pins = "gpio116", "gpio117";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ usb2_dp_hot_plug_detect: usb2-dp-hot-plug-detect-state {
+ pins = "gpio126";
+ function = "usb2_dp";
+ bias-disable;
+ };
+
+ pcie4_default: pcie4-default-state {
+ clkreq-n-pins {
+ pins = "gpio147";
+ function = "pcie4_clk_req_n";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio146";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio148";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ pcie5_default: pcie5-default-state {
+ clkreq-n-pins {
+ pins = "gpio153";
+ function = "pcie5_clk_req_n";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio152";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wake-n-pins {
+ pins = "gpio154";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn7850-bt";
+ max-speed = <3200000>;
+
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ };
+};
+
+&usb_0 {
+ status = "okay";
+};
+
+&usb_0_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_0_hsphy {
+ vdd-supply = <&vreg_l3f_e0_0p91>;
+ vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy {
+ vdda-phy-supply = <&vreg_l4h_e0_1p2>;
+ vdda-pll-supply = <&vreg_l3f_e0_0p91>;
+ refgen-supply = <&vreg_l2f_e0_0p94>;
+
+ status = "okay";
+};
+
+&usb_0_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss_in>;
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in1>;
+};
+
+&usb_1_hsphy {
+ vdd-supply = <&vreg_l3f_e0_0p91>;
+ vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy {
+ vdda-phy-supply = <&vreg_l4h_e0_1p2>;
+ vdda-pll-supply = <&vreg_l1h_e0_0p94>;
+ refgen-supply = <&vreg_l2f_e0_0p94>;
+
+ status = "okay";
+};
+
+&usb_1_qmpphy_out {
+ remote-endpoint = <&pmic_glink_ss_in1>;
+};
+
+/*
+ * usb_2 is not exposed as a connector; its combo-PHY's DP lanes drive the
+ * chassis HDMI bridge (see hdmi-bridge).
+ */
+&usb_2 {
+ maximum-speed = "high-speed";
+
+ phys = <&usb_2_hsphy>;
+ phy-names = "usb2-phy";
+
+ status = "okay";
+};
+
+&usb_2_hsphy {
+ vdd-supply = <&vreg_l3f_e0_0p91>;
+ vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+ status = "okay";
+};
+
+&usb_2_qmpphy {
+ vdda-phy-supply = <&vreg_l4h_e0_1p2>;
+ vdda-pll-supply = <&vreg_l3f_e0_0p91>;
+ refgen-supply = <&vreg_l2f_e0_0p94>;
+
+ /delete-property/ mode-switch;
+ /delete-property/ orientation-switch;
+
+ status = "okay";
+
+ ports {
+ port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /delete-node/ endpoint;
+
+ usb_2_qmpphy_out_dp: endpoint@0 {
+ reg = <0>;
+
+ data-lanes = <3 2 1 0>;
+ remote-endpoint = <&hdmi_bridge_in>;
+ };
+ };
+ };
+};
+
+/* Internal USB2 host for the Elan fingerprint reader (usb 04f3:0ca8). */
+&usb_hs {
+ status = "okay";
+};
+
+&usb_hs_phy {
+ vdd-supply = <&vreg_l2h_e0_0p88>;
+ vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+ status = "okay";
+};
+
+/*
+ * Multiport USB host: port 0 is the chassis USB-A port; port 1 is an
+ * internal USB HID device.
+ */
+&usb_mp {
+ status = "okay";
+};
+
+&usb_mp_hsphy0 {
+ vdd-supply = <&vreg_l2h_e0_0p88>;
+ vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+ status = "okay";
+};
+
+&usb_mp_hsphy1 {
+ vdd-supply = <&vreg_l2h_e0_0p88>;
+ vdda12-supply = <&vreg_l4h_e0_1p2>;
+
+ status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+ vdda-phy-supply = <&vreg_l4h_e0_1p2>;
+ vdda-pll-supply = <&vreg_l2h_e0_0p88>;
+ refgen-supply = <&vreg_l4f_e1_1p2>;
+
+ status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+ vdda-phy-supply = <&vreg_l4h_e0_1p2>;
+ vdda-pll-supply = <&vreg_l2h_e0_0p88>;
+ refgen-supply = <&vreg_l4f_e1_1p2>;
+
+ status = "okay";
+};
--
2.50.1
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH 3/3] firmware: qcom: scm: Allow QSEECOM on HP EliteBook X G2q 14 AI
2026-06-21 4:50 [PATCH 0/3] X2 Elite HP EliteBook X G2q support Jason Pettit
2026-06-21 4:50 ` [PATCH 1/3] dt-bindings: arm: qcom: Add HP EliteBook X G2q 14 AI Jason Pettit
2026-06-21 4:50 ` [PATCH 2/3] arm64: dts: " Jason Pettit
@ 2026-06-21 4:50 ` Jason Pettit
2 siblings, 0 replies; 5+ messages in thread
From: Jason Pettit @ 2026-06-21 4:50 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Akhil P Oommen,
Mahadevan P, Sibi Sankar, Jingyi Wang, Ananthu C V, Jason Pettit
The HP EliteBook X G2q 14" Next Gen AI PC is a Snapdragon X2 Elite
(Glymur) laptop whose firmware exposes EFI variables through QSEECOM.
Add its board compatible to the QSEECOM allowlist so that EFI variable
access (efivarfs) works on this machine.
Without it the kernel reports "qseecom: untested machine, skipping" and
efivarfs is empty.
Signed-off-by: Jason Pettit <jason.pettit@oss.qualcomm.com>
Assisted-by: Claude:claude-opus-4-8
---
drivers/firmware/qcom/qcom_scm.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index 6b601a4b89db..618437f5aac8 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -2296,6 +2296,7 @@ static const struct of_device_id qcom_scm_qseecom_allowlist[] __maybe_unused = {
{ .compatible = "dell,xps13-9345" },
{ .compatible = "ecs,liva-qc710" },
{ .compatible = "hp,elitebook-ultra-g1q" },
+ { .compatible = "hp,elitebook-x-g2q" },
{ .compatible = "hp,omnibook-x14" },
{ .compatible = "huawei,gaokun3" },
{ .compatible = "lenovo,flex-5g" },
--
2.50.1
^ permalink raw reply related [flat|nested] 5+ messages in thread