[PATCH net-next v3 0/8] net: mdio: realtek-rtl9300: Add RTL83xx support

[PATCH net-next v3 0/8] net: mdio: realtek-rtl9300: Add RTL83xx support

[Markus Stockhausen]

The Realtek Otto switch platform consists of four different series

- RTL838x aka maple   : 28 port 1G Switches
- RTL839x aka cypress : 52 port 1G Switches
- RTL930x aka longan  : 28 port 1G/2.5G/10G Switches
- RTL931x aka mango   : 56 port 1G/2.5G/10G Switches

While the MDIO hardware polling unit and its necessity for the MAC 
layer was always well known, no detailed documentation was available.
For this series the MDIO bus was inspected with a logic analyzer for 
a better understanding how polling and kernel access interact on the 
bus. All this will be explained now in the driver comments.

This patch series adds support for the RTL83xx devices. For this

- Enhance device tree binding.
- Add special handling for limitations enforced by hardware polling.
  These already have minor side effects on RTL93xx devices but are even
  more critical for the RTL83xx hardware.
- Add RTL83xx coding.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
---

v2 -> v3:
  - Enhance documentation and make clear that the driver and not the
    kernel must handle the bus mess. (Andrew)
  - Block non-Realtek PHYs on C22 buses to avoid issues with driver
    internal register 31 handling. (Andrew, Chris)
  - Drop C45 over C22 patch. This would need a bus lock/unlock design.
    For all known hardware designs it is not needed. (Andrew)
  - Drop tune_polling() and init_polling() from private structure.
    It is not used in this series and only produces review bot
    questions. (Sashiko)
  - Sort patches for better logical consistency. (Markus)
  - Add device tree patch that was missed in v2. (Markus)
v2: https://lore.kernel.org/netdev/20260629152336.2239826-1-markus.stockhausen@gmx.de/
v2 Sashiko review: https://sashiko.dev/#/patchset/20260629152336.2239826-1-markus.stockhausen%40gmx.de

v1 -> v2:
  - The polling activation logic was refactored. V1 simply activated
    polling after bus probing. Now a dedicated phydev/bus callback
    takes care of this and also handles deferred PHY probing. (Sashiko)
  - Run MMD prefix helper before register 31 (aka Realtek page register) 
    handling. (Jakub's bot)
  - Always run MMD postfix - even if the c22 register access fails. This 
    ensures that the MMD state machine stays consistent. Adapt the error 
    handling inside the postfix function to not overwrite the real MDIO 
    return code (Sashiko, Jakub's bot)
  - Drop unused RTL8390_PHY_CTRL_PARK_PAGE define. Like on RTL931x this 
    field must not be set and thus can be ignored. (Sashiko)
  - Change title in device tree documentation. Because of this do NOT 
    add the Reviewed-by of Krzysztof. (Jakub's bot)
  - Fix wrong use of RTL839x in commit message of patch "c45 over c22 
    mitigation". RTL930x was wrongly named RTL839x in the list of good 
    devices. (Markus)
  - Fix typos (e.g. c22 over c45) in polling documentation (Jakub's bot)
v1: https://lore.kernel.org/netdev/20260613112946.1071411-1-markus.stockhausen@gmx.de/
v1 Sashiko review: https://sashiko.dev/#/patchset/20260613112946.1071411-1-markus.stockhausen@gmx.de


Daniel Golle (1):
  net: phy: add (*notify_phy_attach/detach)() hooks to struct mii_bus

Markus Stockhausen (7):
  dt-bindings: net: realtek,rtl9301-mdio: Add RTL83xx series
  net: mdio: realtek-rtl9300: Add polling documentation
  net: mdio: realtek-rtl9300: Configure hardware polling during probing
  net: mdio: realtek-rtl9300: Add page tracking
  net: mdio: realtek-rtl9300: Increase MDIO timeout
  net: mdio: realtek-rtl9300: Add support for RTL838x
  net: mdio: realtek-rtl9300: Add support for RTL839x

 .../bindings/net/realtek,rtl9301-mdio.yaml    |  14 +-
 drivers/net/mdio/mdio-realtek-rtl9300.c       | 395 +++++++++++++++++-
 drivers/net/phy/phy_device.c                  |   9 +
 include/linux/phy.h                           |   4 +
 4 files changed, 412 insertions(+), 10 deletions(-)

-- 
2.54.0

[PATCH net-next v3 1/8] dt-bindings: net: realtek,rtl9301-mdio: Add RTL83xx series

[Markus Stockhausen]

The lower end Realtek Otto switches provide 1G only and are divided into
two series:

- Maple  : RTL838x up to 28 ports
- Cypress: RTL839x up to 56 ports

The Maple based devices have 3 different SoCs: RTL8380, RTL8381 and
RTL8382. The Cypress series consists of the RTL8391, RTL8392 and
RTL8393 SoCs. The MDIO controller of these switches works like the
existing RTL93xx logic but has different characteristics and different
registers. Add new compatibles in the device tree.

With the extended compatibility list change the title to better reflect
the scope of. Especially add the "Ethernet" tag as these devices have
multiple MDIO controllers.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
---
 .../bindings/net/realtek,rtl9301-mdio.yaml         | 14 +++++++++++++-
 1 file changed, 13 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/net/realtek,rtl9301-mdio.yaml b/Documentation/devicetree/bindings/net/realtek,rtl9301-mdio.yaml
index 271e05bae9c5..67e0b23a8470 100644
--- a/Documentation/devicetree/bindings/net/realtek,rtl9301-mdio.yaml
+++ b/Documentation/devicetree/bindings/net/realtek,rtl9301-mdio.yaml
@@ -4,7 +4,7 @@
 $id: http://devicetree.org/schemas/net/realtek,rtl9301-mdio.yaml#
 $schema: http://devicetree.org/meta-schemas/core.yaml#
 
-title: Realtek RTL9300 MDIO Controller
+title: Realtek Otto Switches Ethernet MDIO Controller
 
 maintainers:
   - Chris Packham <chris.packham@alliedtelesis.co.nz>
@@ -12,6 +12,16 @@ maintainers:
 properties:
   compatible:
     oneOf:
+      - items:
+          - enum:
+              - realtek,rtl8381-mdio
+              - realtek,rtl8382-mdio
+          - const: realtek,rtl8380-mdio
+      - items:
+          - enum:
+              - realtek,rtl8392-mdio
+              - realtek,rtl8393-mdio
+          - const: realtek,rtl8391-mdio
       - items:
           - enum:
               - realtek,rtl9302b-mdio
@@ -24,6 +34,8 @@ properties:
               - realtek,rtl9313-mdio
           - const: realtek,rtl9311-mdio
       - enum:
+          - realtek,rtl8380-mdio
+          - realtek,rtl8391-mdio
           - realtek,rtl9301-mdio
           - realtek,rtl9311-mdio
 
-- 
2.54.0

Re: [PATCH net-next v3 1/8] dt-bindings: net: realtek,rtl9301-mdio: Add RTL83xx series

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 53 bytes --]

Acked-by: Conor Dooley <conor.dooley@microchip.com>


[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[PATCH net-next v3 2/8] net: mdio: realtek-rtl9300: Add polling documentation

[Markus Stockhausen]

Add a detailed explanation how the hardware polling unit in the
Realtek Otto switches works. This simplifies developing future
patches and reviewing them.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
---
 drivers/net/mdio/mdio-realtek-rtl9300.c | 68 +++++++++++++++++++++++++
 1 file changed, 68 insertions(+)

diff --git a/drivers/net/mdio/mdio-realtek-rtl9300.c b/drivers/net/mdio/mdio-realtek-rtl9300.c
index 892ed3780a65..562f9c7f2895 100644
--- a/drivers/net/mdio/mdio-realtek-rtl9300.c
+++ b/drivers/net/mdio/mdio-realtek-rtl9300.c
@@ -35,6 +35,74 @@
  *
  * The driver works out the mapping based on the MDIO bus described in device tree and phandles on
  * the ethernet-ports property.
+ *
+ * The devices have a hardware polling unit that runs in the background without any CPU load. It
+ * constantly scans the MDIO bus and the attached PHYs and updates the MAC status registers.
+ *
+ * How does the polling work?
+ *
+ * Each device has a SMI_POLL_CTRL register. A per-port bitmask decides if the hardware polling of
+ * the associated bus/address is active or not. The hardware runs a tight loop over this and for
+ * each set polling bit it issues a status check for the PHY. Attaching a logic analyzer to the
+ * MDIO bus of an RTL8380 and RTL8393 gives the following commands (in kernel notation):
+ *
+ *	RTL8380				RTL8393
+ *	---------------------------	---------------------------
+ *	phy_write(phy, 31, 0x0);	phy_read(phy, 0);
+ *	phy_write(phy, 13, 0x7);	phy_read(phy, 1);
+ *	phy_write(phy, 14, 0x3c);	phy_read(phy, 4);
+ *	phy_write(phy, 13, 0x8007);	phy_read(phy, 5);
+ *	phy_read(phy, 14);		phy_read(phy, 6);
+ *	phy_write(phy, 13, 0x7);	phy_read(phy, 9);
+ *	phy_write(phy, 14, 0x3d);	phy_read(phy, 10);
+ *	phy_write(phy, 13, 0x8007);	phy_read(phy, 15);
+ *	phy_read(phy, 14);		phy_write(phy, 13, 0x7);
+ *	phy_read(phy, 9);		phy_write(phy, 14, 0x3c);
+ *	phy_read(phy, 10);		phy_write(phy, 13, 0x4007);
+ *	phy_read(phy, 15);		phy_read(phy, 14);
+ *	phy_read(phy, 0);		phy_write(phy, 13, 0x7);
+ *	phy_read(phy, 1);		phy_write(phy, 14, 0x3d);
+ *	phy_read(phy, 4);		phy_write(phy, 13, 0x4007);
+ *	phy_read(phy, 5);		phy_read(phy, 14);
+ *	phy_read(phy, 6);
+ *
+ * From the above snippets it polls MDIO_AN_EEE_ADV and MDIO_AN_EEE_LPABLE via C45 over C22. As
+ * of now it is unclear how the hardware decides if a PHY supports these registers. After one PHY
+ * status is read, the polling engine goes over to the next PHY. Basically the bus is always busy
+ * and the MAC status is updated in real-time.
+ *
+ * How does MDIO access from kernel work?
+ *
+ * When issuing MDIO accesses via an MMIO based interface the final write to the command register
+ * sets a "run command now" bit. Between two polling sequences for different PHYs the hardware
+ * checks if a user command needs to run and sends it onto the bus. Afterwards it simply continues
+ * its polling work. Inspecting the command sequence for a paged read on the logic analyzer gives:
+ *
+ *	RTL8380				RTL8393
+ *	---------------------------	---------------------------
+ *	phy_write(phy, 31, page);	phy_write(phy, 31, page);
+ *	phy_write(phy, reg, value);	phy_write(phy, reg, value);
+ *					phy_write(phy, 31, 0);
+ *
+ * What does this mean?
+ *
+ * There are slight differences in polling and PHY access between the models but the challenge
+ * stays the same. On the one hand that greatly simplifies the MAC layer, on the other hand it
+ * has some implications for the kernel PHY subsystem.
+ *
+ * - Without the polling and a proper MAC status, some of the link handling features do not work.
+ *   Especially an unpopulated MAC_LINK_STS register cancels operations to other MAC registers.
+ * - The Realtek page register 31 is magically modified in the background so that polling will
+ *   read the right data. On the RTL838x polling simply resets it to zero. Other devices seem
+ *   to track the page access "magically" in the background.
+ * - A C45 over C22 kernel access sequence is most likely to fail because chances are high that
+ *   the polling engine overwrites registers 13/14 in between.
+ * - PHY firmware loading can have issues. Especially if a PHY is designed to expect a clean
+ *   sequence of registers and values without deviation.
+ * - An access to one PHY will need to wait for the next free slot of the polling engine.
+ *
+ * Conclusion: The Realtek MDIO bus driver PHY access must know and handle any interference that
+ * arises from the above described hardware polling.
  */
 
 #include <linux/bitfield.h>
-- 
2.54.0

[PATCH net-next v3 3/8] net: phy: add (*notify_phy_attach/detach)() hooks to struct mii_bus

[Markus Stockhausen]

From: Daniel Golle <daniel@makrotopia.org>

Some MDIO buses require to program PHY polling registers depending on
the PHY type. RealTek switch SoCs are the most prominent example of a
DSA switch which doesn't allow to program MAC speed, duplex and
flow-control settings without using PHY polling to do so [1].

Avoid a half-baked solution in the MDIO bus driver because

- it must reinvent the bus scanning to determine the PHYs and
- it must anticipate the right point in time (e.g. deferred PHYs).

Hence there is a need to inform the MDIO bus driver that a PHY is
being attached or detached. Provide two simple hooks in struct
mii_bus which are called

- right after a PHY has been attached
- just before the PHY is going to be detached

Remark! A slightly different version of this patch was part of a
former series [2]. The discussion already showed that an initialization
hook should be placed somewhere late during the whole setup. This
commit implants it right after phy_init_hw() as suggested. On top of
this it adds the detach hook.

[1] https://github.com/openwrt/openwrt/pull/21515#discussion_r2714069716
[2] https://lore.kernel.org/netdev/cover.1769053496.git.daniel@makrotopia.org/

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
---
 drivers/net/phy/phy_device.c | 9 +++++++++
 include/linux/phy.h          | 4 ++++
 2 files changed, 13 insertions(+)

diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
index 0615228459ef..676cbf183350 100644
--- a/drivers/net/phy/phy_device.c
+++ b/drivers/net/phy/phy_device.c
@@ -1876,6 +1876,12 @@ int phy_attach_direct(struct net_device *dev, struct phy_device *phydev,
 	if (err)
 		goto error;
 
+	if (phydev->mdio.bus->notify_phy_attach) {
+		err = phydev->mdio.bus->notify_phy_attach(phydev);
+		if (err)
+			goto error;
+	}
+
 	phy_resume(phydev);
 
 	/**
@@ -1919,6 +1925,9 @@ void phy_detach(struct phy_device *phydev)
 	struct module *ndev_owner = NULL;
 	struct mii_bus *bus;
 
+	if (phydev->mdio.bus->notify_phy_detach)
+		phydev->mdio.bus->notify_phy_detach(phydev);
+
 	if (phydev->devlink) {
 		device_link_del(phydev->devlink);
 		phydev->devlink = NULL;
diff --git a/include/linux/phy.h b/include/linux/phy.h
index 199a7aaa341b..3160ca99deab 100644
--- a/include/linux/phy.h
+++ b/include/linux/phy.h
@@ -376,6 +376,10 @@ struct mii_bus {
 			 int regnum, u16 val);
 	/** @reset: Perform a reset of the bus */
 	int (*reset)(struct mii_bus *bus);
+	/** @notify_phy_attach: Perform post-attach handling */
+	int (*notify_phy_attach)(struct phy_device *phydev);
+	/** @notify_phy_detach: Perform pre-detach handling */
+	void (*notify_phy_detach)(struct phy_device *phydev);
 
 	/** @stats: Statistic counters per device on the bus */
 	struct mdio_bus_stats stats[PHY_MAX_ADDR];
-- 
2.54.0

Re: [PATCH net-next v3 3/8] net: phy: add (*notify_phy_attach/detach)() hooks to struct mii_bus

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 2 potential issue(s) to consider:

New issues:
- [Medium] The newly added `notify_phy_detach` callback is invoked unconditionally during `phy_detach()`, violating attach/detach symmetry if attachment fails.

Pre-existing issues:
- [High] Calling `phy_attach_direct` on an already-attached PHY destructively removes its existing attachment.
--

commit 43b033c0e004225e5826f1197f795406afea2c07
Author: Daniel Golle <daniel@makrotopia.org>

net: phy: add (*notify_phy_attach/detach)() hooks to struct mii_bus

This commit adds notify_phy_attach and notify_phy_detach hooks to
struct mii_bus. This allows MDIO bus drivers to handle PHY-specific
initialization and teardown without duplicating bus scanning logic.

Link: https://github.com/openwrt/openwrt/pull/21515#discussion_r2714069716
Link: https://lore.kernel.org/netdev/cover.1769053496.git.daniel@makrotopia.org/

> diff --git a/drivers/net/phy/phy_device.c b/drivers/net/phy/phy_device.c
> index 0615228459ef4..676cbf183350d 100644
> --- a/drivers/net/phy/phy_device.c
> +++ b/drivers/net/phy/phy_device.c
> @@ -1876,6 +1876,12 @@ int phy_attach_direct(struct net_device *dev, struct phy_device *phydev,
>  	if (err)
>  		goto error;
>  
> +	if (phydev->mdio.bus->notify_phy_attach) {
> +		err = phydev->mdio.bus->notify_phy_attach(phydev);
> +		if (err)
> +			goto error;

[Severity: High]
This is a pre-existing issue, but does jumping to the error label
destructively tear down valid state if the PHY was already attached?

If phy_attach_direct() is mistakenly called on a PHY that is already
attached, it correctly catches it here:

phy_attach_direct() {
    ...
    if (phydev->attached_dev) {
        dev_err(&dev->dev, "PHY already attached\n");
        err = -EBUSY;
        goto error;
    }
    ...
}

However, by jumping to the error label, it calls phy_detach(). Since
phy_detach() unconditionally removes sysfs links, unbinds the PHY, and
clears phydev->attached_dev, won't this tear down the pre-existing
attachment and leave the original caller with dangling references?

> +	}
> +
>  	phy_resume(phydev);
>  

[ ... ]

> @@ -1919,6 +1925,9 @@ void phy_detach(struct phy_device *phydev)
>  	struct module *ndev_owner = NULL;
>  	struct mii_bus *bus;
>  
> +	if (phydev->mdio.bus->notify_phy_detach)
> +		phydev->mdio.bus->notify_phy_detach(phydev);
> +

[Severity: Medium]
Will this result in asymmetric attach/detach notifications on error paths?

If phy_init_hw() fails earlier in phy_attach_direct(), or if this new
notify_phy_attach callback itself fails, the code jumps to the error
label and calls phy_detach().

Because phy_detach() unconditionally calls notify_phy_detach(), won't
the bus driver receive a detach notification for a PHY that was never
successfully attached?

If future bus drivers rely on these callbacks to allocate resources or
increment reference counts, could this cause double-frees or underflows?

>  	if (phydev->devlink) {
>  		device_link_del(phydev->devlink);
>  		phydev->devlink = NULL;

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260705163532.2853959-1-markus.stockhausen@gmx.de?part=3

[PATCH net-next v3 4/8] net: mdio: realtek-rtl9300: Configure hardware polling during probing

[Markus Stockhausen]

During PHY probing and configuration complex configuration sequences
might be issued and firmware might be loaded. Hardware polling can
interfere badly with that. E.g. a hardware polling MMD c45 over c22
request might break an ongoing firmware loading sequence.

To avoid such issues the polling of the Realtek Otto switches can be
(de)activated with one or two 32 bit mask registers. Each bit enables
(=1) or disables (=0) the polling of the corresponding port. Make use
of this as follows:

- Disable polling for all ports when the MDIO driver starts.
- Reenable polling just after the PHY has been attached.
- Disable polling just before the PHY is being detached.

This synchronizes the kernel and hardware polling to some extent. It
gracefully handles deferred probing of PHYs in case the driver is
loaded asynchronously during boot. Additionally it brings the hardware
polling into a consistent operation mode for devices where U-Boot does
not take care.

[1] https://github.com/openwrt/openwrt/blob/main/target/linux/realtek/files-6.18/drivers/net/mdio/mdio-realtek-otto.c#L818
[2] https://lore.kernel.org/netdev/680696024a8648535ce6dee771fe4de67802e0e8.1769053496.git.daniel@makrotopia.org/

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
---
 drivers/net/mdio/mdio-realtek-rtl9300.c | 77 +++++++++++++++++++++++++
 1 file changed, 77 insertions(+)

diff --git a/drivers/net/mdio/mdio-realtek-rtl9300.c b/drivers/net/mdio/mdio-realtek-rtl9300.c
index 562f9c7f2895..c36244cd9a66 100644
--- a/drivers/net/mdio/mdio-realtek-rtl9300.c
+++ b/drivers/net/mdio/mdio-realtek-rtl9300.c
@@ -139,6 +139,7 @@
 #define   RTL9300_PHY_CTRL_INDATA		GENMASK(31, 16)
 #define   RTL9300_PHY_CTRL_DATA			GENMASK(15, 0)
 #define RTL9300_SMI_ACCESS_PHY_CTRL_3		0xcb7c
+#define RTL9300_SMI_POLL_CTRL			0xca90
 #define RTL9300_SMI_PORT0_5_ADDR_CTRL		0xcb80
 
 #define RTL9310_NUM_BUSES			4
@@ -164,6 +165,7 @@
 #define   RTL9310_PHY_CTRL_INDATA		GENMASK(15, 0)
 #define RTL9310_SMI_INDRT_ACCESS_MMD_CTRL	0x0c18
 #define RTL9310_SMI_PORT_ADDR_CTRL		0x0c74
+#define RTL9310_SMI_PORT_POLLING_CTRL		0x0ccc
 #define RTL9310_SMI_PORT_POLLING_SEL		0x0c9c
 
 #define PHY_CTRL_CMD				BIT(0)
@@ -194,6 +196,7 @@ struct otto_emdio_priv {
 	const struct otto_emdio_info *info;
 	struct regmap *regmap;
 	struct mutex lock; /* protect HW access */
+	DECLARE_BITMAP(phy_poll, MAX_PORTS);
 	DECLARE_BITMAP(valid_ports, MAX_PORTS);
 	u8 smi_bus[MAX_PORTS];
 	u8 smi_addr[MAX_PORTS];
@@ -211,6 +214,7 @@ struct otto_emdio_info {
 	u8 num_buses;
 	u8 num_ports;
 	u16 num_pages;
+	u32 poll_ctrl;
 	int (*setup_controller)(struct otto_emdio_priv *priv);
 	int (*read_c22)(struct mii_bus *bus, int port, int regnum, u32 *value);
 	int (*read_c45)(struct mii_bus *bus, int port, int dev_addr, int regnum, u32 *value);
@@ -246,6 +250,14 @@ static struct otto_emdio_priv *otto_emdio_bus_to_priv(struct mii_bus *bus)
 	return chan->priv;
 }
 
+static int otto_emdio_set_port_polling(struct otto_emdio_priv *priv, int port, bool active)
+{
+	lockdep_assert_held(&priv->lock);
+
+	return regmap_assign_bits(priv->regmap, priv->info->poll_ctrl + (port / 32) * 4,
+				  BIT(port % 32), active);
+}
+
 static int otto_emdio_run_cmd(struct mii_bus *bus, u32 cmd,
 			      struct otto_emdio_cmd_regs *cmd_data)
 {
@@ -576,6 +588,47 @@ static int otto_emdio_9310_setup_controller(struct otto_emdio_priv *priv)
 	return 0;
 }
 
+static int otto_emdio_notify_phy_attach(struct phy_device *phydev)
+{
+	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(phydev->mdio.bus);
+	int port = otto_emdio_phy_to_port(phydev->mdio.bus, phydev->mdio.addr);
+	int ret;
+
+	if (port < 0)
+		return port;
+
+	if (test_bit(port, priv->phy_poll))
+		return 0;
+
+	scoped_guard(mutex, &priv->lock) {
+		ret = otto_emdio_set_port_polling(priv, port, true);
+		if (!ret)
+			__set_bit(port, priv->phy_poll);
+	}
+
+	return ret;
+}
+
+static void otto_emdio_notify_phy_detach(struct phy_device *phydev)
+{
+	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(phydev->mdio.bus);
+	int port = otto_emdio_phy_to_port(phydev->mdio.bus, phydev->mdio.addr);
+	struct mii_bus *bus = phydev->mdio.bus;
+	int ret;
+
+	if (port < 0)
+		return;
+
+	scoped_guard(mutex, &priv->lock) {
+		ret = otto_emdio_set_port_polling(priv, port, false);
+		if (!ret)
+			__clear_bit(port, priv->phy_poll);
+	}
+	
+	if (ret)
+		dev_err(bus->parent, "failed to disable polling for port %d\n", port);
+}
+
 static int otto_emdio_probe_one(struct device *dev, struct otto_emdio_priv *priv,
 				 struct fwnode_handle *node)
 {
@@ -605,6 +658,9 @@ static int otto_emdio_probe_one(struct device *dev, struct otto_emdio_priv *priv
 		bus->write = otto_emdio_write_c22;
 	}
 	bus->parent = dev;
+	bus->notify_phy_attach = otto_emdio_notify_phy_attach;
+	bus->notify_phy_detach = otto_emdio_notify_phy_detach;
+
 	chan = bus->priv;
 	chan->mdio_bus = mdio_bus;
 	chan->priv = priv;
@@ -721,6 +777,21 @@ static int otto_emdio_map_ports(struct device *dev)
 	return err;
 }
 
+static int otto_emdio_init_polling(struct otto_emdio_priv *priv)
+{
+	int err;
+
+	for (int port = 0; port < priv->info->num_ports; port++) {
+		scoped_guard(mutex, &priv->lock) {
+			err = otto_emdio_set_port_polling(priv, port, false);
+			if (err)
+				return err;
+		}
+	}
+
+	return 0;
+}
+
 static int otto_emdio_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -740,6 +811,10 @@ static int otto_emdio_probe(struct platform_device *pdev)
 	if (IS_ERR(priv->regmap))
 		return PTR_ERR(priv->regmap);
 
+	err = otto_emdio_init_polling(priv);
+	if (err)
+		return err;
+
 	platform_set_drvdata(pdev, priv);
 
 	err = otto_emdio_map_ports(dev);
@@ -780,6 +855,7 @@ static const struct otto_emdio_info otto_emdio_9300_info = {
 	.num_buses = RTL9300_NUM_BUSES,
 	.num_ports = RTL9300_NUM_PORTS,
 	.num_pages = RTL9300_NUM_PAGES,
+	.poll_ctrl = RTL9300_SMI_POLL_CTRL,
 	.setup_controller = otto_emdio_9300_setup_controller,
 	.read_c22 = otto_emdio_9300_read_c22,
 	.read_c45 = otto_emdio_9300_read_c45,
@@ -805,6 +881,7 @@ static const struct otto_emdio_info otto_emdio_9310_info = {
 	.num_buses = RTL9310_NUM_BUSES,
 	.num_pages = RTL9310_NUM_PAGES,
 	.num_ports = RTL9310_NUM_PORTS,
+	.poll_ctrl = RTL9310_SMI_PORT_POLLING_CTRL,
 	.setup_controller = otto_emdio_9310_setup_controller,
 	.read_c22 = otto_emdio_9310_read_c22,
 	.read_c45 = otto_emdio_9310_read_c45,
-- 
2.54.0

Re: [PATCH net-next v3 4/8] net: mdio: realtek-rtl9300: Configure hardware polling during probing

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] Data race due to unprotected lockless read of `priv->phy_poll`.
--

commit 5dc09b6df4d4ed1cb80ef56b8de6e9aa03870333
Author: Markus Stockhausen <markus.stockhausen@gmx.de>

net: mdio: realtek-rtl9300: Configure hardware polling during probing

This commit synchronizes kernel and hardware polling for Realtek Otto switches
by disabling polling for all ports on start and managing it per-PHY during
attach and detach. This prevents hardware polling from interfering with
complex configuration sequences or firmware loading.

Link: https://github.com/openwrt/openwrt/blob/main/target/linux/realtek/files-6.18/drivers/net/mdio/mdio-realtek-otto.c#L818
Link: https://lore.kernel.org/netdev/680696024a8648535ce6dee771fe4de67802e0e8.1769053496.git.daniel@makrotopia.org/

> diff --git a/drivers/net/mdio/mdio-realtek-rtl9300.c b/drivers/net/mdio/mdio-realtek-rtl9300.c
> index 562f9c7f2895d..c36244cd9a66e 100644
> --- a/drivers/net/mdio/mdio-realtek-rtl9300.c
> +++ b/drivers/net/mdio/mdio-realtek-rtl9300.c

[ ... ]

> @@ -576,6 +588,47 @@ static int otto_emdio_9310_setup_controller(struct otto_emdio_priv *priv)
>  	return 0;
>  }
>  
> +static int otto_emdio_notify_phy_attach(struct phy_device *phydev)
> +{
> +	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(phydev->mdio.bus);
> +	int port = otto_emdio_phy_to_port(phydev->mdio.bus, phydev->mdio.addr);
> +	int ret;
> +
> +	if (port < 0)
> +		return port;
> +
> +	if (test_bit(port, priv->phy_poll))
> +		return 0;

[Severity: Medium]
Could this lockless read of priv->phy_poll result in a data race?

While this test_bit() is lockless, the updates in the guarded sections below
use the non-atomic __set_bit() and __clear_bit(). If multiple PHYs on the
same MDIO bus are attached or detached concurrently, the plain
read-modify-write from __set_bit() or __clear_bit() on the same word could
race with this read, causing KCSAN warnings and undefined behavior.

Should this test_bit() check be moved inside the scoped_guard() block, which
safely supports early returns?

> +
> +	scoped_guard(mutex, &priv->lock) {
> +		ret = otto_emdio_set_port_polling(priv, port, true);
> +		if (!ret)
> +			__set_bit(port, priv->phy_poll);
> +	}
> +
> +	return ret;
> +}
> +
> +static void otto_emdio_notify_phy_detach(struct phy_device *phydev)
> +{
> +	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(phydev->mdio.bus);
> +	int port = otto_emdio_phy_to_port(phydev->mdio.bus, phydev->mdio.addr);
> +	struct mii_bus *bus = phydev->mdio.bus;
> +	int ret;
> +
> +	if (port < 0)
> +		return;
> +
> +	scoped_guard(mutex, &priv->lock) {
> +		ret = otto_emdio_set_port_polling(priv, port, false);
> +		if (!ret)
> +			__clear_bit(port, priv->phy_poll);
> +	}
> +	
> +	if (ret)
> +		dev_err(bus->parent, "failed to disable polling for port %d\n", port);
> +}

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260705163532.2853959-1-markus.stockhausen@gmx.de?part=4

[PATCH net-next v3 5/8] net: mdio: realtek-rtl9300: Add page tracking

[Markus Stockhausen]

The hardware polling unit of the Realtek switches has a very special
handling for PHY register 31 (aka Realtek page register) in place.

- On the RTL838x it is permanently reset to zero.
- On other devices there is some magic saving/restoring (aka parking)
  in the background in place.

This makes access to PHYs a gamble.

As of now all known existing hardware designs have Realtek PHYs for 1G
connectivity. Otherwise the polling engine and the MAC status update
will not work at all and the vendor SDK would fail totally.

This driver differentiates clearly between C22 and C45 buses. During
probing it enables only one of the protocols for a bus. So it is safe
to assume that any C22 access will only target a Realtek based 1G PHY.
For safety reasons block any non-Realtek PHY on a C22 bus.

Intercept access to register 31 and handle it internally. Store the
desired value for each port in the driver. When issuing hardware access
to other registers add the page to the command towards the controller.
This given, the hardware will run two consecutive c22 commands that are
not interrupted by polling.

  ... hardware poll ...
  phy_write(phy, 31, page)
  phy_write(phy, reg, value)
  ... hardware poll ...

Remark! To keep this simple, writes to register 31 are only accepted if
they are lower than the device specific raw page - 0..4094/8190.
Otherwise -EINVAL is returned. Under the above assumption (Only 1G
Realtek PHYs on c22 bus) this is no limitation.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
---
 drivers/net/mdio/mdio-realtek-rtl9300.c | 34 ++++++++++++++++++++-----
 1 file changed, 28 insertions(+), 6 deletions(-)

diff --git a/drivers/net/mdio/mdio-realtek-rtl9300.c b/drivers/net/mdio/mdio-realtek-rtl9300.c
index c36244cd9a66..a5cac0d04114 100644
--- a/drivers/net/mdio/mdio-realtek-rtl9300.c
+++ b/drivers/net/mdio/mdio-realtek-rtl9300.c
@@ -171,6 +171,7 @@
 #define PHY_CTRL_CMD				BIT(0)
 #define PHY_CTRL_MMD_DEVAD			GENMASK(20, 16)
 #define PHY_CTRL_MMD_REG			GENMASK(15, 0)
+#define PHY_VENDOR_REALTEK			0x001cc800
 
 #define MAP_ADDRS_PER_REG			6
 #define MAP_BITS_PER_ADDR			5
@@ -198,6 +199,7 @@ struct otto_emdio_priv {
 	struct mutex lock; /* protect HW access */
 	DECLARE_BITMAP(phy_poll, MAX_PORTS);
 	DECLARE_BITMAP(valid_ports, MAX_PORTS);
+	u16 page[MAX_PORTS];
 	u8 smi_bus[MAX_PORTS];
 	u8 smi_addr[MAX_PORTS];
 	bool smi_bus_is_c45[MAX_SMI_BUSSES];
@@ -351,7 +353,7 @@ static int otto_emdio_9300_read_c22(struct mii_bus *bus, int port, int regnum, u
 	struct otto_emdio_cmd_regs cmd_data = {
 		.c22_data	= FIELD_PREP(RTL9300_PHY_CTRL_REG_ADDR, regnum) |
 				  FIELD_PREP(RTL9300_PHY_CTRL_PARK_PAGE, 0x1f) |
-				  FIELD_PREP(RTL9300_PHY_CTRL_MAIN_PAGE, RAW_PAGE(priv)),
+				  FIELD_PREP(RTL9300_PHY_CTRL_MAIN_PAGE, priv->page[port]),
 		.io_data	= FIELD_PREP(RTL9300_PHY_CTRL_INDATA, port),
 	};
 
@@ -365,7 +367,7 @@ static int otto_emdio_9300_write_c22(struct mii_bus *bus, int port, int regnum,
 	struct otto_emdio_cmd_regs cmd_data = {
 		.c22_data	= FIELD_PREP(RTL9300_PHY_CTRL_REG_ADDR, regnum) |
 				  FIELD_PREP(RTL9300_PHY_CTRL_PARK_PAGE, 0x1f) |
-				  FIELD_PREP(RTL9300_PHY_CTRL_MAIN_PAGE, RAW_PAGE(priv)),
+				  FIELD_PREP(RTL9300_PHY_CTRL_MAIN_PAGE, priv->page[port]),
 		.io_data	= FIELD_PREP(RTL9300_PHY_CTRL_INDATA, value),
 		.port_mask_low	= BIT(port),
 	};
@@ -405,7 +407,7 @@ static int otto_emdio_9310_read_c22(struct mii_bus *bus, int port, int regnum, u
 	struct otto_emdio_cmd_regs cmd_data = {
 		.broadcast	= FIELD_PREP(RTL9310_BC_PORT_ID, port),
 		.c22_data	= FIELD_PREP(RTL9310_PHY_CTRL_REG_ADDR, regnum) |
-				  FIELD_PREP(RTL9310_PHY_CTRL_MAIN_PAGE, RAW_PAGE(priv)),
+				  FIELD_PREP(RTL9310_PHY_CTRL_MAIN_PAGE, priv->page[port]),
 	};
 
 	return otto_emdio_read_cmd(bus, RTL9310_PHY_CTRL_TYPE_C22, &cmd_data,
@@ -417,7 +419,7 @@ static int otto_emdio_9310_write_c22(struct mii_bus *bus, int port, int regnum,
 	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(bus);
 	struct otto_emdio_cmd_regs cmd_data = {
 		.c22_data	= FIELD_PREP(RTL9310_PHY_CTRL_REG_ADDR, regnum) |
-				  FIELD_PREP(RTL9310_PHY_CTRL_MAIN_PAGE, RAW_PAGE(priv)),
+				  FIELD_PREP(RTL9310_PHY_CTRL_MAIN_PAGE, priv->page[port]),
 		.io_data	= FIELD_PREP(RTL9310_PHY_CTRL_INDATA, value),
 		.port_mask_high	= (u32)(BIT_ULL(port) >> 32),
 		.port_mask_low	= (u32)(BIT_ULL(port)),
@@ -463,8 +465,12 @@ static int otto_emdio_read_c22(struct mii_bus *bus, int phy_id, int regnum)
 	if (port < 0)
 		return port;
 
-	scoped_guard(mutex, &priv->lock)
+	scoped_guard(mutex, &priv->lock) {
+		if (regnum == 31)
+			return priv->page[port];
+
 		ret = priv->info->read_c22(bus, port, regnum, &value);
+	}
 
 	return ret ? ret : value;
 }
@@ -478,8 +484,17 @@ static int otto_emdio_write_c22(struct mii_bus *bus, int phy_id, int regnum, u16
 	if (port < 0)
 		return port;
 
-	scoped_guard(mutex, &priv->lock)
+	scoped_guard(mutex, &priv->lock) {
+		if (regnum == 31) {
+			if (value >= RAW_PAGE(priv))
+				return -EINVAL;
+
+			priv->page[port] = value;
+			return 0;
+		}
+
 		ret = priv->info->write_c22(bus, port, regnum, value);
+	}
 
 	return ret;
 }
@@ -592,6 +607,7 @@ static int otto_emdio_notify_phy_attach(struct phy_device *phydev)
 {
 	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(phydev->mdio.bus);
 	int port = otto_emdio_phy_to_port(phydev->mdio.bus, phydev->mdio.addr);
+	struct otto_emdio_chan *chan = phydev->mdio.bus->priv;
 	int ret;
 
 	if (port < 0)
@@ -600,6 +616,12 @@ static int otto_emdio_notify_phy_attach(struct phy_device *phydev)
 	if (test_bit(port, priv->phy_poll))
 		return 0;
 
+	if (!priv->smi_bus_is_c45[chan->mdio_bus] &&
+	    (!phy_id_compare_vendor(phydev->phy_id, PHY_VENDOR_REALTEK))) {
+		phydev_err(phydev, "Only Realtek PHYs allowed on C22 bus\n");
+		return -EOPNOTSUPP;
+	}
+
 	scoped_guard(mutex, &priv->lock) {
 		ret = otto_emdio_set_port_polling(priv, port, true);
 		if (!ret)
-- 
2.54.0

[PATCH net-next v3 6/8] net: mdio: realtek-rtl9300: Increase MDIO timeout

[Markus Stockhausen]

RTL838x devices with 28 ports produce PHY access timeout errors during
one of three boots while waiting for MDIO command completion. This is
currently set to 1ms.

Background: Access to the Realtek Otto ethernet MDIO bus must wait for
a free slot between two hardware polls. The polling sequence consists
of at least 17 commands on the RTL838x devices. This delay can be nicely
seen when disabling polling completely. The following times are measured
on a bus running on the default 2.5MHz. Time measured is from the last
register write that sets the command-start-bit until the hardware
responds with the command-finished-bit set.

- average c22 read with polling enabled on all ports: ~380us
- average c22 read with polling enabled on one port: ~380us
- average c22 read with polling completely disabled: ~180us

For this bus frequency the bare hardware runtime for a single command
(32 bit preamble + 32 bit data) is ~25us. So the hardware adds quite
some overhead. On top of this comes the fact that the RTL838x devices
are low on resources (500Mhz 4Kec core with 16K cache).

Increase the timeout to 10ms to be on the safe side.

Remark! In a future patch the bus clock frequency will be made
configurable with a minimum frequency of 1.25MHz. Setting this
(e.g. for debugging purposes) doubles the command run times but
will safely stay below 10ms.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
---
 drivers/net/mdio/mdio-realtek-rtl9300.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/net/mdio/mdio-realtek-rtl9300.c b/drivers/net/mdio/mdio-realtek-rtl9300.c
index a5cac0d04114..c73e370d912a 100644
--- a/drivers/net/mdio/mdio-realtek-rtl9300.c
+++ b/drivers/net/mdio/mdio-realtek-rtl9300.c
@@ -268,9 +268,9 @@ static int otto_emdio_run_cmd(struct mii_bus *bus, u32 cmd,
 	u32 cmdstate;
 	int ret;
 
-	/* Defensive pre check just in case something goes horrible wrong */
+	/* Defensive pre check just in case something goes horribly wrong */
 	ret = regmap_read_poll_timeout(priv->regmap, info->cmd_regs.c22_data,
-				       cmdstate, !(cmdstate & PHY_CTRL_CMD), 10, 1000);
+				       cmdstate, !(cmdstate & PHY_CTRL_CMD), 10, 10000);
 	if (ret)
 		return ret;
 
@@ -310,7 +310,7 @@ static int otto_emdio_run_cmd(struct mii_bus *bus, u32 cmd,
 		return ret;
 
 	ret = regmap_read_poll_timeout(priv->regmap, info->cmd_regs.c22_data,
-				       cmdstate, !(cmdstate & PHY_CTRL_CMD), 10, 1000);
+				       cmdstate, !(cmdstate & PHY_CTRL_CMD), 10, 10000);
 	if (ret)
 		return ret;
 
-- 
2.54.0

[PATCH net-next v3 7/8] net: mdio: realtek-rtl9300: Add support for RTL838x

[Markus Stockhausen]

The MDIO driver has been prepared for multiple device support. Add all
required bits for the RTL838x (aka maple) series. This is straightforward
but some things are worth mentioning.

- The device has a lot in common with the RTL930x series. 28 ports, 4096
  (Realtek) pages, 4 MMIO registers
- The MDIO engine has no fail bit. Thus the mask is set to zero
- There is only one SMI bus for 1G PHYs. No bus_map_base register exists.
- The setup_controller() function needs no c45 setup but must activate
  the PHY access.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
---
 drivers/net/mdio/mdio-realtek-rtl9300.c | 108 ++++++++++++++++++++++++
 1 file changed, 108 insertions(+)

diff --git a/drivers/net/mdio/mdio-realtek-rtl9300.c b/drivers/net/mdio/mdio-realtek-rtl9300.c
index c73e370d912a..e7c811614fd6 100644
--- a/drivers/net/mdio/mdio-realtek-rtl9300.c
+++ b/drivers/net/mdio/mdio-realtek-rtl9300.c
@@ -119,6 +119,28 @@
 #include <linux/property.h>
 #include <linux/regmap.h>
 
+#define RTL8380_NUM_BUSES			1
+#define RTL8380_NUM_PAGES			4096
+#define RTL8380_NUM_PORTS			28
+#define RTL8380_SMI_GLB_CTRL			0xa100
+#define   RTL8380_SMI_PHY_PATCH_DONE		BIT(15)
+#define RTL8380_SMI_ACCESS_PHY_CTRL_0		0xa1b8
+#define RTL8380_SMI_ACCESS_PHY_CTRL_1		0xa1bc
+#define   RTL8380_PHY_CTRL_REG_ADDR		GENMASK(24, 20)
+#define   RTL8380_PHY_CTRL_PARK_PAGE		GENMASK(19, 15)
+#define   RTL8380_PHY_CTRL_MAIN_PAGE		GENMASK(14, 3)
+#define   RTL8380_PHY_CTRL_WRITE		BIT(2)
+#define   RTL8380_PHY_CTRL_READ			0
+#define   RTL8380_PHY_CTRL_TYPE_C45		BIT(1)
+#define   RTL8380_PHY_CTRL_TYPE_C22		0
+#define   RTL8380_PHY_CTRL_FAIL			0 /* no fail indicator */
+#define RTL8380_SMI_ACCESS_PHY_CTRL_2		0xa1c0
+#define   RTL8380_PHY_CTRL_INDATA		GENMASK(31, 16)
+#define   RTL8380_PHY_CTRL_DATA			GENMASK(15, 0)
+#define RTL8380_SMI_ACCESS_PHY_CTRL_3		0xa1c4
+#define RTL8380_SMI_POLL_CTRL			0xa17c
+#define RTL8380_SMI_PORT0_5_ADDR_CTRL		0xa1c8
+
 #define RTL9300_NUM_BUSES			4
 #define RTL9300_NUM_PAGES			4096
 #define RTL9300_NUM_PORTS			28
@@ -347,6 +369,60 @@ static int otto_emdio_write_cmd(struct mii_bus *bus, u32 cmd,
 	return otto_emdio_run_cmd(bus, cmd | priv->info->cmd_write, cmd_data);
 }
 
+static int otto_emdio_8380_read_c22(struct mii_bus *bus, int port, int regnum, u32 *value)
+{
+	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(bus);
+	struct otto_emdio_cmd_regs cmd_data = {
+		.c22_data	= FIELD_PREP(RTL8380_PHY_CTRL_REG_ADDR, regnum) |
+				  FIELD_PREP(RTL8380_PHY_CTRL_PARK_PAGE, 0x1f) |
+				  FIELD_PREP(RTL8380_PHY_CTRL_MAIN_PAGE, priv->page[port]),
+		.io_data	= FIELD_PREP(RTL8380_PHY_CTRL_INDATA, port),
+	};
+
+	return otto_emdio_read_cmd(bus, RTL8380_PHY_CTRL_TYPE_C22, &cmd_data,
+				   RTL8380_PHY_CTRL_DATA, value);
+}
+
+static int otto_emdio_8380_write_c22(struct mii_bus *bus, int port, int regnum, u16 value)
+{
+	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(bus);
+	struct otto_emdio_cmd_regs cmd_data = {
+		.c22_data	= FIELD_PREP(RTL8380_PHY_CTRL_REG_ADDR, regnum) |
+				  FIELD_PREP(RTL8380_PHY_CTRL_PARK_PAGE, 0x1f) |
+				  FIELD_PREP(RTL8380_PHY_CTRL_MAIN_PAGE, priv->page[port]),
+		.io_data	= FIELD_PREP(RTL8380_PHY_CTRL_INDATA, value),
+		.port_mask_low	= BIT(port),
+	};
+
+	return otto_emdio_write_cmd(bus, RTL8380_PHY_CTRL_TYPE_C22, &cmd_data);
+}
+
+static int otto_emdio_8380_read_c45(struct mii_bus *bus, int port,
+				    int dev_addr, int regnum, u32 *value)
+{
+	struct otto_emdio_cmd_regs cmd_data = {
+		.c45_data	= FIELD_PREP(PHY_CTRL_MMD_DEVAD, dev_addr) |
+				  FIELD_PREP(PHY_CTRL_MMD_REG, regnum),
+		.io_data	= FIELD_PREP(RTL8380_PHY_CTRL_INDATA, port),
+	};
+
+	return otto_emdio_read_cmd(bus, RTL8380_PHY_CTRL_TYPE_C45, &cmd_data,
+				   RTL8380_PHY_CTRL_DATA, value);
+}
+
+static int otto_emdio_8380_write_c45(struct mii_bus *bus, int port,
+				     int dev_addr, int regnum, u16 value)
+{
+	struct otto_emdio_cmd_regs cmd_data = {
+		.c45_data	= FIELD_PREP(PHY_CTRL_MMD_DEVAD, dev_addr) |
+				  FIELD_PREP(PHY_CTRL_MMD_REG, regnum),
+		.io_data	= FIELD_PREP(RTL8380_PHY_CTRL_INDATA, value),
+		.port_mask_low	= BIT(port),
+	};
+
+	return otto_emdio_write_cmd(bus, RTL8380_PHY_CTRL_TYPE_C45, &cmd_data);
+}
+
 static int otto_emdio_9300_read_c22(struct mii_bus *bus, int port, int regnum, u32 *value)
 {
 	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(bus);
@@ -567,6 +643,15 @@ static int otto_emdio_setup_topology(struct otto_emdio_priv *priv)
 	return 0;
 }
 
+static int otto_emdio_8380_setup_controller(struct otto_emdio_priv *priv)
+{
+	/*
+	 * PHY_PATCH_DONE enables PHY control via SoC. This is required for PHY access, including
+	 * patching and must be set before the PHYs are probed.
+	 */
+	return regmap_set_bits(priv->regmap, RTL8380_SMI_GLB_CTRL, RTL8380_SMI_PHY_PATCH_DONE);
+}
+
 static int otto_emdio_9300_setup_controller(struct otto_emdio_priv *priv)
 {
 	u32 glb_ctrl_mask = 0, glb_ctrl_val = 0;
@@ -862,6 +947,28 @@ static int otto_emdio_probe(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct otto_emdio_info otto_emdio_8380_info = {
+	.addr_map_base = RTL8380_SMI_PORT0_5_ADDR_CTRL,
+	.cmd_fail = RTL8380_PHY_CTRL_FAIL,
+	.cmd_read = RTL8380_PHY_CTRL_READ,
+	.cmd_write = RTL8380_PHY_CTRL_WRITE,
+	.cmd_regs = {
+		.c22_data = RTL8380_SMI_ACCESS_PHY_CTRL_1,
+		.c45_data = RTL8380_SMI_ACCESS_PHY_CTRL_3,
+		.io_data = RTL8380_SMI_ACCESS_PHY_CTRL_2,
+		.port_mask_low = RTL8380_SMI_ACCESS_PHY_CTRL_0,
+	},
+	.num_buses = RTL8380_NUM_BUSES,
+	.num_pages = RTL8380_NUM_PAGES,
+	.num_ports = RTL8380_NUM_PORTS,
+	.poll_ctrl = RTL8380_SMI_POLL_CTRL,
+	.setup_controller = otto_emdio_8380_setup_controller,
+	.read_c22 = otto_emdio_8380_read_c22,
+	.read_c45 = otto_emdio_8380_read_c45,
+	.write_c22 = otto_emdio_8380_write_c22,
+	.write_c45 = otto_emdio_8380_write_c45,
+};
+
 static const struct otto_emdio_info otto_emdio_9300_info = {
 	.addr_map_base = RTL9300_SMI_PORT0_5_ADDR_CTRL,
 	.bus_map_base = RTL9300_SMI_PORT0_15_POLLING_SEL,
@@ -912,6 +1019,7 @@ static const struct otto_emdio_info otto_emdio_9310_info = {
 };
 
 static const struct of_device_id otto_emdio_ids[] = {
+	{ .compatible = "realtek,rtl8380-mdio", .data = &otto_emdio_8380_info },
 	{ .compatible = "realtek,rtl9301-mdio", .data = &otto_emdio_9300_info },
 	{ .compatible = "realtek,rtl9311-mdio", .data = &otto_emdio_9310_info },
 	{}
-- 
2.54.0

[PATCH net-next v3 8/8] net: mdio: realtek-rtl9300: Add support for RTL839x

[Markus Stockhausen]

The MDIO driver has been prepared for multiple device support. Add all
required bits for the RTL839x (aka cypress) series. This is straightforward
but some things are worth mentioning.

- The device has a lot in common with the RTL931x series. 8192 (Realtek)
  pages and 7 MMIO registers
- There are two SMI buses for 1G PHYs. Neither the bus nor address map
  registers exist.
- The hardware has not much to configure. So the setup_controller()
  function is not needed.
- c22 read/write functions must be called with PARK_PAGE = 0. Keep code
  clean and avoid setting it to zero, matching the behavior of the RTL9310
  logic.

Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
---
 drivers/net/mdio/mdio-realtek-rtl9300.c | 102 ++++++++++++++++++++++++
 1 file changed, 102 insertions(+)

diff --git a/drivers/net/mdio/mdio-realtek-rtl9300.c b/drivers/net/mdio/mdio-realtek-rtl9300.c
index e7c811614fd6..d797d8f01c66 100644
--- a/drivers/net/mdio/mdio-realtek-rtl9300.c
+++ b/drivers/net/mdio/mdio-realtek-rtl9300.c
@@ -141,6 +141,28 @@
 #define RTL8380_SMI_POLL_CTRL			0xa17c
 #define RTL8380_SMI_PORT0_5_ADDR_CTRL		0xa1c8
 
+#define RTL8390_NUM_BUSES			2
+#define RTL8390_NUM_PAGES			8192
+#define RTL8390_NUM_PORTS			52
+#define RTL8390_BCAST_PHYID_CTRL		0x03ec
+#define RTL8390_PHYREG_ACCESS_CTRL		0x03dc
+#define   RTL8390_PHY_CTRL_REG_ADDR		GENMASK(9, 5)
+#define   RTL8390_PHY_CTRL_MAIN_PAGE		GENMASK(22, 10)
+#define   RTL8390_PHY_CTRL_FAIL			BIT(1)
+#define   RTL8390_PHY_CTRL_WRITE		BIT(3)
+#define   RTL8390_PHY_CTRL_READ			0
+#define   RTL8390_PHY_CTRL_TYPE_C45		BIT(2)
+#define   RTL8390_PHY_CTRL_TYPE_C22		0
+#define RTL8390_PHYREG_CTRL			0x03e0
+#define   RTL8390_PHY_CTRL_EXT_PAGE		GENMASK(8, 0)
+#define RTL8390_PHYREG_DATA_CTRL		0x03f0
+#define   RTL8390_PHY_CTRL_INDATA		GENMASK(31, 16)
+#define   RTL8390_PHY_CTRL_DATA			GENMASK(15, 0)
+#define RTL8390_PHYREG_MMD_CTRL			0x03f4
+#define RTL8390_PHYREG_PORT_CTRL_LOW		0x03e4
+#define RTL8390_PHYREG_PORT_CTRL_HIGH		0x03e8
+#define RTL8390_SMI_PORT_POLLING_CTRL		0x03fc
+
 #define RTL9300_NUM_BUSES			4
 #define RTL9300_NUM_PAGES			4096
 #define RTL9300_NUM_PORTS			28
@@ -423,6 +445,62 @@ static int otto_emdio_8380_write_c45(struct mii_bus *bus, int port,
 	return otto_emdio_write_cmd(bus, RTL8380_PHY_CTRL_TYPE_C45, &cmd_data);
 }
 
+static int otto_emdio_8390_read_c22(struct mii_bus *bus, int port, int regnum, u32 *value)
+{
+	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(bus);
+	struct otto_emdio_cmd_regs cmd_data = {
+		.c22_data	= FIELD_PREP(RTL8390_PHY_CTRL_REG_ADDR, regnum) |
+				  FIELD_PREP(RTL8390_PHY_CTRL_MAIN_PAGE, priv->page[port]),
+		.ext_page	= FIELD_PREP(RTL8390_PHY_CTRL_EXT_PAGE, 0x1ff),
+		.io_data	= FIELD_PREP(RTL8390_PHY_CTRL_INDATA, port),
+	};
+
+	return otto_emdio_read_cmd(bus, RTL8390_PHY_CTRL_TYPE_C22, &cmd_data,
+				   RTL8390_PHY_CTRL_DATA, value);
+}
+
+static int otto_emdio_8390_write_c22(struct mii_bus *bus, int port, int regnum, u16 value)
+{
+	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(bus);
+	struct otto_emdio_cmd_regs cmd_data = {
+		.c22_data	= FIELD_PREP(RTL8390_PHY_CTRL_REG_ADDR, regnum) |
+				  FIELD_PREP(RTL8390_PHY_CTRL_MAIN_PAGE, priv->page[port]),
+		.ext_page	= FIELD_PREP(RTL8390_PHY_CTRL_EXT_PAGE, 0x1ff),
+		.io_data	= FIELD_PREP(RTL8390_PHY_CTRL_INDATA, value),
+		.port_mask_high	= (u32)(BIT_ULL(port) >> 32),
+		.port_mask_low	= (u32)(BIT_ULL(port)),
+	};
+
+	return otto_emdio_write_cmd(bus, RTL8390_PHY_CTRL_TYPE_C22, &cmd_data);
+}
+
+static int otto_emdio_8390_read_c45(struct mii_bus *bus, int port,
+				    int dev_addr, int regnum, u32 *value)
+{
+	struct otto_emdio_cmd_regs cmd_data = {
+		.c45_data	= FIELD_PREP(PHY_CTRL_MMD_DEVAD, dev_addr) |
+				  FIELD_PREP(PHY_CTRL_MMD_REG, regnum),
+		.io_data	= FIELD_PREP(RTL8390_PHY_CTRL_INDATA, port),
+	};
+
+	return otto_emdio_read_cmd(bus, RTL8390_PHY_CTRL_TYPE_C45, &cmd_data,
+				   RTL8390_PHY_CTRL_DATA, value);
+}
+
+static int otto_emdio_8390_write_c45(struct mii_bus *bus, int port,
+				     int dev_addr, int regnum, u16 value)
+{
+	struct otto_emdio_cmd_regs cmd_data = {
+		.c45_data	= FIELD_PREP(PHY_CTRL_MMD_DEVAD, dev_addr) |
+				  FIELD_PREP(PHY_CTRL_MMD_REG, regnum),
+		.io_data	= FIELD_PREP(RTL8390_PHY_CTRL_INDATA, value),
+		.port_mask_high	= (u32)(BIT_ULL(port) >> 32),
+		.port_mask_low	= (u32)(BIT_ULL(port)),
+	};
+
+	return otto_emdio_write_cmd(bus, RTL8390_PHY_CTRL_TYPE_C45, &cmd_data);
+}
+
 static int otto_emdio_9300_read_c22(struct mii_bus *bus, int port, int regnum, u32 *value)
 {
 	struct otto_emdio_priv *priv = otto_emdio_bus_to_priv(bus);
@@ -969,6 +1047,29 @@ static const struct otto_emdio_info otto_emdio_8380_info = {
 	.write_c45 = otto_emdio_8380_write_c45,
 };
 
+static const struct otto_emdio_info otto_emdio_8390_info = {
+	.cmd_fail = RTL8390_PHY_CTRL_FAIL,
+	.cmd_read = RTL8390_PHY_CTRL_READ,
+	.cmd_write = RTL8390_PHY_CTRL_WRITE,
+	.cmd_regs = {
+		.broadcast = RTL8390_BCAST_PHYID_CTRL,
+		.c22_data = RTL8390_PHYREG_ACCESS_CTRL,
+		.c45_data = RTL8390_PHYREG_MMD_CTRL,
+		.ext_page = RTL8390_PHYREG_CTRL,
+		.io_data = RTL8390_PHYREG_DATA_CTRL,
+		.port_mask_low = RTL8390_PHYREG_PORT_CTRL_LOW,
+		.port_mask_high = RTL8390_PHYREG_PORT_CTRL_HIGH,
+	},
+	.num_buses = RTL8390_NUM_BUSES,
+	.num_pages = RTL8390_NUM_PAGES,
+	.num_ports = RTL8390_NUM_PORTS,
+	.poll_ctrl = RTL8390_SMI_PORT_POLLING_CTRL,
+	.read_c22 = otto_emdio_8390_read_c22,
+	.read_c45 = otto_emdio_8390_read_c45,
+	.write_c22 = otto_emdio_8390_write_c22,
+	.write_c45 = otto_emdio_8390_write_c45,
+};
+
 static const struct otto_emdio_info otto_emdio_9300_info = {
 	.addr_map_base = RTL9300_SMI_PORT0_5_ADDR_CTRL,
 	.bus_map_base = RTL9300_SMI_PORT0_15_POLLING_SEL,
@@ -1020,6 +1121,7 @@ static const struct otto_emdio_info otto_emdio_9310_info = {
 
 static const struct of_device_id otto_emdio_ids[] = {
 	{ .compatible = "realtek,rtl8380-mdio", .data = &otto_emdio_8380_info },
+	{ .compatible = "realtek,rtl8391-mdio", .data = &otto_emdio_8390_info },
 	{ .compatible = "realtek,rtl9301-mdio", .data = &otto_emdio_9300_info },
 	{ .compatible = "realtek,rtl9311-mdio", .data = &otto_emdio_9310_info },
 	{}
-- 
2.54.0