[PATCH v5 2/2] arm64: dts: rockchip: Add ArmSoM CM5 and CM5-IO

[Jiaxing Hu <gahing@gahingwoo.com>]

Add the ArmSoM CM5, an RK3576 compute module (rk3576-armsom-cm5.dtsi),
and its CM5-IO carrier (rk3576-armsom-cm5-io.dts). The module has the
RK806 PMIC, HYM8563 RTC, eMMC, GMAC0 with an on-module MotorComm YT8531
PHY, and the SDIO bus for the on-module WiFi. The carrier adds HDMI, a
GbE RJ45, two USB-A ports behind a USB3 hub, USB-C with FUSB302 and DP
alt-mode, a PCIe 2.0 x1 M.2 slot, microSD, status LEDs and a 40-pin
header.

The YT8531 has no crystal and takes the SoC 25 MHz reference
(REFCLKO25M_GMAC0_OUT), described as a clock on the PHY node and enabled
by the PHY driver. The PHY is named explicitly so it is instantiated
from the device tree without an MDIO ID probe, which the PHY cannot
answer until that clock is running. Its reset is described at the MDIO
bus level so mdiobus releases it before the scan.

Signed-off-by: Jiaxing Hu <gahing@gahingwoo.com>
---
 arch/arm64/boot/dts/rockchip/Makefile         |   1 +
 .../dts/rockchip/rk3576-armsom-cm5-io.dts     | 402 +++++++++++++
 .../boot/dts/rockchip/rk3576-armsom-cm5.dtsi  | 558 ++++++++++++++++++
 3 files changed, 961 insertions(+)
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts
 create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5.dtsi

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index cb55c6b70..3ec0b6e20 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -165,6 +165,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-display-vz.dtbo
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-io-expander.dtbo
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-100ask-dshanpi-a1.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-cm5-io.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-sige5.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-sige5-v1.2-wifibt.dtbo
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-evb1-v10.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts b/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts
new file mode 100644
index 000000000..40d9be0c6
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts
@@ -0,0 +1,402 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * ArmSoM CM5-IO - official carrier board for the ArmSoM CM5 (RK3576) module.
+ *
+ * Carrier provides:
+ *   - Full-size HDMI 2.1 (HDMI TX via HDPTX PHY)
+ *   - Gigabit Ethernet RJ45 (GMAC0 + on-module YT8531)
+ *   - 2x USB-A behind a USB3 hub (combphy1 + u2phy1)
+ *   - USB-C with PD/altmode (FUSB302 on i2c0, combphy0 + USBDP PHY)
+ *   - M.2 PCIe 2.0 x1 slot (combphy0 as PCIe lane)
+ *   - microSD card slot
+ *   - Green/red status LEDs, 40-pin RPi-compatible header
+ *   - 12 V DC barrel jack
+ *
+ * Copyright (c) 2024 ArmSoM
+ * Copyright (c) 2026 Jiaxing Hu <gahing@gahingwoo.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include <dt-bindings/usb/pd.h>
+#include "rk3576-armsom-cm5.dtsi"
+
+/ {
+	model = "ArmSoM CM5-IO";
+	compatible = "armsom,cm5-io", "armsom,cm5", "rockchip,rk3576";
+
+	aliases {
+		ethernet0 = &gmac0;
+		mmc0 = &sdhci;
+		mmc1 = &sdmmc;
+	};
+
+	chosen {
+		stdout-path = "serial0:1500000n8";
+	};
+
+	/* Full-size HDMI Type-A connector, driven by the SoC HDMI TX. */
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi_out_con>;
+			};
+		};
+	};
+
+	/*
+	 * Carrier status LEDs (schematic ARMSOM-CM5-IO-1V1_20240829):
+	 *   green - GPIO2 PD0 (net LED_GREEN_EN)
+	 *   red   - GPIO2 PD1 (net LED_RED_EN)
+	 */
+	leds: leds {
+		compatible = "gpio-leds";
+
+		led_green: led-green {
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_STATUS;
+			gpios = <&gpio2 RK_PD0 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&led_green_en>;
+			default-state = "on";
+		};
+
+		led_red: led-red {
+			color = <LED_COLOR_ID_RED>;
+			function = LED_FUNCTION_FAULT;
+			gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&led_red_en>;
+			default-state = "off";
+		};
+	};
+
+	/* Carrier power tree: 12 V barrel jack -> 5 V -> peripheral rails. */
+	vcc_12v0_dcin: regulator-vcc-12v0-dcin {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_12v0_dcin";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <12000000>;
+		regulator-max-microvolt = <12000000>;
+	};
+
+	vcc_5v0_sys: regulator-vcc-5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_12v0_dcin>;
+	};
+
+	vcc_5v0_device: regulator-vcc-5v0-device {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_5v0_device";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_12v0_dcin>;
+	};
+
+	/* PCIe 3.3 V for the M.2 slot, gated by GPIO0 PC3. */
+	vcc_3v3_pcie: regulator-vcc-3v3-pcie {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie_pwr_en>;
+		regulator-name = "vcc_3v3_pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		gpios = <&gpio0 RK_PC3 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <5000>;
+		vin-supply = <&vcc_5v0_sys>;
+	};
+
+	/* USB-C / OTG 5 V, gated by GPIO2 PB6. */
+	vcc_5v0_typec0: regulator-vcc-5v0-typec0 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio2 RK_PB6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_otg0_pwren>;
+		regulator-name = "vcc_5v0_typec0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v0_device>;
+	};
+
+	/* USB-A host 5 V (through the hub), gated by GPIO4 PB0. */
+	vcc_5v0_usbhost: regulator-vcc-5v0-usbhost {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usb_host_pwren>;
+		regulator-name = "vcc_5v0_usbhost";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc_5v0_device>;
+	};
+};
+
+/*
+ * ComboPHY0 -> PCIe lane (M.2 slot); ComboPHY1 -> USB3 lane (USB-A hub).
+ */
+&combphy0_ps {
+	status = "okay";
+};
+
+&combphy1_psu {
+	status = "okay";
+};
+
+&hdmi {
+	status = "okay";
+};
+
+&hdmi_in {
+	hdmi_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi>;
+	};
+};
+
+&hdmi_out {
+	hdmi_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi_sound {
+	status = "okay";
+};
+
+&hdptxphy {
+	status = "okay";
+};
+
+/* SAI6 is the I2S CPU DAI feeding the HDMI audio path. */
+&sai6 {
+	status = "okay";
+};
+
+/* I2C0: FUSB302 USB-C PD controller @ 0x22, pinctrl i2c0m1 (PC4/PC5). */
+&i2c0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0m1_xfer>;
+
+	usbc0: usb-typec@22 {
+		compatible = "fcs,fusb302";
+		reg = <0x22>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&usbc0_int>;
+		vbus-supply = <&vcc_5v0_typec0>;
+
+		usb_con: connector {
+			compatible = "usb-c-connector";
+			label = "USB-C";
+			data-role = "dual";
+			power-role = "dual";
+			try-power-role = "sink";
+			op-sink-microwatt = <1000000>;
+			sink-pdos =
+				<PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+				 PDO_FIXED(9000, 3000, PDO_FIXED_USB_COMM)
+				 PDO_FIXED(12000, 3000, PDO_FIXED_USB_COMM)>;
+			source-pdos =
+				<PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+
+			altmodes {
+				displayport {
+					svid = /bits/ 16 <0xff01>;
+					vdo = <0xffffffff>;
+				};
+			};
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+					usbc0_orien_sw: endpoint {
+						remote-endpoint = <&usbdp_phy_orientation_switch>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+					usbc0_role_sw: endpoint {
+						remote-endpoint = <&usb_drd0_role_switch>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+					dp_altmode_mux: endpoint {
+						remote-endpoint = <&usbdp_phy_dp_altmode_mux>;
+					};
+				};
+			};
+		};
+	};
+};
+
+/*
+ * PCIe 2.0 x1 M.2 slot. Reset GPIO2 PB1, power vcc_3v3_pcie (GPIO0 PC3).
+ */
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset>;
+	reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc_3v3_pcie>;
+	status = "okay";
+};
+
+/* microSD card slot. */
+&sdmmc {
+	bus-width = <4>;
+	cap-mmc-highspeed;
+	cap-sd-highspeed;
+	disable-wp;
+	max-frequency = <200000000>;
+	no-sdio;
+	no-mmc;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3_s3>;
+	vqmmc-supply = <&vccio_sd_s0>;
+	status = "okay";
+};
+
+&u2phy0 {
+	status = "okay";
+};
+
+&u2phy0_otg {
+	phy-supply = <&vcc_5v0_typec0>;
+	status = "okay";
+};
+
+&u2phy1 {
+	status = "okay";
+};
+
+&u2phy1_otg {
+	phy-supply = <&vcc_5v0_usbhost>;
+	status = "okay";
+};
+
+/* Debug UART0 on the 40-pin header. */
+&uart0 {
+	pinctrl-0 = <&uart0m0_xfer>;
+	status = "okay";
+};
+
+/* USB DRD0: USB-C (USBDP SuperSpeed + USB2 HS), OTG with FUSB302 role-switch. */
+&usb_drd0_dwc3 {
+	dr_mode = "otg";
+	usb-role-switch;
+	status = "okay";
+
+	port {
+		usb_drd0_role_switch: endpoint {
+			remote-endpoint = <&usbc0_role_sw>;
+		};
+	};
+};
+
+/* USB DRD1: USB-A ports behind the hub (combphy1 SuperSpeed + USB2 HS). */
+&usb_drd1_dwc3 {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbdp_phy {
+	status = "okay";
+	mode-switch;
+	orientation-switch;
+	sbu1-dc-gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;
+	sbu2-dc-gpios = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;
+
+	port {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		usbdp_phy_orientation_switch: endpoint@0 {
+			reg = <0>;
+			remote-endpoint = <&usbc0_orien_sw>;
+		};
+
+		usbdp_phy_dp_altmode_mux: endpoint@1 {
+			reg = <1>;
+			remote-endpoint = <&dp_altmode_mux>;
+		};
+	};
+};
+
+&vop {
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi_in_vp0>;
+	};
+};
+
+&pinctrl {
+	leds {
+		/* GPIO2 PD0 - green carrier LED */
+		led_green_en: led-green-en {
+			rockchip,pins = <2 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		/* GPIO2 PD1 - red carrier LED */
+		led_red_en: led-red-en {
+			rockchip,pins = <2 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		/* GPIO0 PC3 - PCIe power enable */
+		pcie_pwr_en: pcie-pwr-en {
+			rockchip,pins = <0 RK_PC3 RK_FUNC_GPIO &pcfg_pull_down>;
+		};
+		/* GPIO2 PB1 - PCIe PERST# */
+		pcie_reset: pcie-reset {
+			rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb {
+		/* GPIO4 PB0 - USB host 5V enable */
+		usb_host_pwren: usb-host-pwren {
+			rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		/* GPIO2 PB6 - USB OTG / Type-C 5V enable */
+		usb_otg0_pwren: usb-otg0-pwren {
+			rockchip,pins = <2 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+		/* GPIO0 PB4 - FUSB302 INT# (active-low) */
+		usbc0_int: usbc0-int {
+			rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5.dtsi b/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5.dtsi
new file mode 100644
index 000000000..b6977b973
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5.dtsi
@@ -0,0 +1,558 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * ArmSoM CM5 - Rockchip RK3576 compute module (Raspberry Pi CM4 form factor).
+ *
+ * Common to all CM5 carriers. The carrier .dts includes this file, sets the
+ * board model/compatible, and adds carrier-specific peripherals.
+ *
+ * On-module devices:
+ *   - RK806 PMIC on I2C1
+ *   - HYM8563 RTC on I2C2
+ *   - eMMC (SDHCI)
+ *   - GMAC0 + MotorComm YT8531 Gigabit Ethernet PHY (RGMII)
+ *   - SYN43752 WiFi 6 + BT 5.x (SDIO + UART4)
+ *
+ * Copyright (c) 2024 ArmSoM
+ * Copyright (c) 2026 Jiaxing Hu <gahing@gahingwoo.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3576.dtsi"
+
+/ {
+	compatible = "armsom,cm5", "rockchip,rk3576";
+
+	vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v1_nldo_s3";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&vcc_5v0_sys>;
+	};
+
+	vcc_1v2_ufs_vccq_s0: regulator-vcc-1v2-ufs-vccq-s0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v2_ufs_vccq_s0";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1200000>;
+		regulator-max-microvolt = <1200000>;
+		vin-supply = <&vcc_5v0_sys>;
+	};
+
+	vcc_1v8_s0: regulator-vcc-1v8-s0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v8_s0";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_1v8_s3>;
+	};
+
+	vcc_1v8_ufs_vccq2_s0: regulator-vcc-1v8-ufs-vccq2-s0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v8_ufs_vccq2_s0";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vcc_1v8_s3>;
+	};
+
+	vcc_2v0_pldo_s3: regulator-vcc-2v0-pldo-s3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_2v0_pldo_s3";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <2000000>;
+		regulator-max-microvolt = <2000000>;
+		vin-supply = <&vcc_5v0_sys>;
+	};
+
+	vcc_3v3_s0: regulator-vcc-3v3-s0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_s0";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_3v3_s3>;
+	};
+
+	vcc_3v3_ufs_s0: regulator-vcc-ufs-s0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_3v3_ufs_s0";
+		regulator-boot-on;
+		regulator-always-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc_5v0_sys>;
+	};
+
+	/*
+	 * WiFi power sequencer for SYN43752. Reset GPIO1 PC6 active-low,
+	 * clock from the HYM8563 RTC oscillator.
+	 */
+	sdio_pwrseq: sdio-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		clocks = <&hym8563>;
+		clock-names = "ext_clock";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wifi_reg_on>;
+		reset-gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&cpu_b2 {
+	cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&cpu_b3 {
+	cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+/*
+ * GMAC0 drives an on-module MotorComm YT8531. The PHY has no local crystal and
+ * takes the SoC 25 MHz reference (REFCLKO25M_GMAC0_OUT); ethm0_clk0_25m_out
+ * routes that clock to the pad, and the PHY node consumes and enables it.
+ */
+&gmac0 {
+	phy-mode = "rgmii-id";
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy0>;
+	phy-supply = <&vcc_3v3_s3>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&eth0m0_miim
+		     &eth0m0_tx_bus2
+		     &eth0m0_rx_bus2
+		     &eth0m0_rgmii_clk
+		     &eth0m0_rgmii_bus
+		     &ethm0_clk0_25m_out>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu_s0>;
+	status = "okay";
+};
+
+/* I2C1: RK806 PMIC @ 0x23 (interrupt on GPIO0 PA6). */
+&i2c1 {
+	status = "okay";
+
+	pmic@23 {
+		compatible = "rockchip,rk806";
+		reg = <0x23>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA6 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+
+		system-power-controller;
+
+		vcc1-supply = <&vcc_5v0_sys>;
+		vcc2-supply = <&vcc_5v0_sys>;
+		vcc3-supply = <&vcc_5v0_sys>;
+		vcc4-supply = <&vcc_5v0_sys>;
+		vcc5-supply = <&vcc_5v0_sys>;
+		vcc6-supply = <&vcc_5v0_sys>;
+		vcc7-supply = <&vcc_5v0_sys>;
+		vcc8-supply = <&vcc_5v0_sys>;
+		vcc9-supply = <&vcc_5v0_sys>;
+		vcc10-supply = <&vcc_5v0_sys>;
+		vcc11-supply = <&vcc_2v0_pldo_s3>;
+		vcc12-supply = <&vcc_5v0_sys>;
+		vcc13-supply = <&vcc_1v1_nldo_s3>;
+		vcc14-supply = <&vcc_1v1_nldo_s3>;
+		vcca-supply = <&vcc_5v0_sys>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		rk806_dvs1_null: dvs1-null-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs2_null: dvs2-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs3_null: dvs3-null-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun0";
+		};
+
+		regulators {
+			vdd_cpu_big_s0: dcdc-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_cpu_big_s0";
+				regulator-enable-ramp-delay = <400>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_npu_s0: dcdc-reg2 {
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_npu_s0";
+				regulator-enable-ramp-delay = <400>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_lit_s0: dcdc-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_cpu_lit_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vcc_3v3_s3: dcdc-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_3v3_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vdd_gpu_s0: dcdc-reg5 {
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <900000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_gpu_s0";
+				regulator-enable-ramp-delay = <400>;
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			vddq_ddr_s0: dcdc-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vddq_ddr_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_logic_s0: dcdc-reg7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <800000>;
+				regulator-name = "vdd_logic_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3: dcdc-reg8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd2_ddr_s3: dcdc-reg9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vdd2_ddr_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vdd_ddr_s0: dcdc-reg10 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-name = "vdd_ddr_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_1v8_s0: pldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca_1v8_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pldo2_s0: pldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pldo2_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_1v2_s0: pldo-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-name = "vdda_1v2_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca_3v3_s0: pldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcca_3v3_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd_s0: pldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vccio_sd_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcca1v8_pldo6_s3: pldo-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcca1v8_pldo6_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_0v75_s3: nldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+				regulator-name = "vdd_0v75_s3";
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdda_ddr_pll_s0: nldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-name = "vdda_ddr_pll_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda0v75_hdmi_s0: nldo-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <837500>;
+				regulator-max-microvolt = <837500>;
+				regulator-name = "vdda0v75_hdmi_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v85_s0: nldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-name = "vdda_0v85_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdda_0v75_s0: nldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+				regulator-name = "vdda_0v75_s0";
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+/* I2C2: HYM8563 RTC @ 0x51 (interrupt on GPIO0 PA0). */
+&i2c2 {
+	status = "okay";
+
+	hym8563: rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		clock-output-names = "hym8563";
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PA0 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&hym8563_int>;
+		wakeup-source;
+		#clock-cells = <0>;
+	};
+};
+
+/*
+ * The PHY reset has to be described at the MDIO bus level: mdiobus releases a
+ * bus level reset before it scans for PHY IDs, whereas the per-PHY reset-gpios
+ * is only applied by phylib once the PHY has already been found, which never
+ * happens while the YT8531 is still held in reset.
+ *
+ * The compatible names the YT8531 explicitly so phylib instantiates the PHY
+ * from the device tree without an MDIO ID probe; the crystal-less PHY does not
+ * answer on MDIO until its driver has enabled the reference clock below.
+ */
+&mdio0 {
+	reset-gpios = <&gpio2 RK_PB3 GPIO_ACTIVE_LOW>;
+	reset-delay-us = <20000>;
+	reset-post-delay-us = <100000>;
+
+	rgmii_phy0: phy@1 {
+		compatible = "ethernet-phy-id4f51.e91b",
+			     "ethernet-phy-ieee802.3-c22";
+		reg = <0x1>;
+		clocks = <&cru REFCLKO25M_GMAC0_OUT>;
+	};
+};
+
+&saradc {
+	vref-supply = <&vcca_1v8_s0>;
+	status = "okay";
+};
+
+/* eMMC: on-module, HS400 200 MHz with enhanced strobe. */
+&sdhci {
+	bus-width = <8>;
+	full-pwr-cycle-in-suspend;
+	max-frequency = <200000000>;
+	mmc-hs400-1_8v;
+	mmc-hs400-enhanced-strobe;
+	no-sdio;
+	no-sd;
+	non-removable;
+	/delete-property/ supports-cqe;
+	status = "okay";
+};
+
+/* SDIO: SYN43752 WiFi, power-sequenced by sdio_pwrseq, clock from HYM8563. */
+&sdio {
+	bus-width = <4>;
+	cap-sdio-irq;
+	disable-wp;
+	keep-power-in-suspend;
+	mmc-pwrseq = <&sdio_pwrseq>;
+	no-sd;
+	no-mmc;
+	non-removable;
+	sd-uhs-sdr50;
+	sd-uhs-sdr104;
+	vmmc-supply = <&vcc_3v3_s3>;
+	vqmmc-supply = <&vcc_1v8_s3>;
+	wakeup-source;
+	status = "okay";
+};
+
+/* UART4: Bluetooth (SYN43752). */
+&uart4 {
+	pinctrl-0 = <&uart4m1_xfer &uart4m1_ctsn &uart4m1_rtsn>;
+	pinctrl-names = "default";
+	uart-has-rtscts;
+	status = "okay";
+};
+
+&pinctrl {
+	hym8563 {
+		hym8563_int: hym8563-int {
+			rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	wireless-wlan {
+		/* GPIO1 PC6 - WiFi power enable / reset (sdio_pwrseq) */
+		wifi_reg_on: wifi-reg-on {
+			rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+};
-- 
2.43.0