* [PATCH v4 2/3] arm64: dts: qcom: sm8550: add UART11 node
2026-07-22 7:36 [PATCH v4 0/3] arm64: qcom: add Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
2026-07-22 7:36 ` [PATCH v4 1/3] dt-bindings: arm: qcom: document the Ayaneo Pocket DS Alexandre Hamamdjian via B4 Relay
@ 2026-07-22 7:36 ` Alexandre Hamamdjian via B4 Relay
2026-07-22 7:36 ` [PATCH v4 3/3] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
2 siblings, 0 replies; 5+ messages in thread
From: Alexandre Hamamdjian via B4 Relay @ 2026-07-22 7:36 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Alexandre Hamamdjian,
Konrad Dybcio
From: Alexandre Hamamdjian <azkali.limited@gmail.com>
Add the QUPv3_2 SE3 UART (UART11) controller node and its default
pinctrl state to sm8550.dtsi, so boards with a peripheral wired to
that serial engine can enable it through &uart11.
The serial engine at 0x88c000 is already described as i2c11 and spi11,
so the UART node takes the same qup_opp_table_120mhz they use: it is
the same block behind the same GCC_QUPV3_WRAP2_S3_CLK, and its core
clock tops out at 120 MHz rather than the 100 MHz the other table
allows. TX and RX are biased pull-up, matching qup_uart14_default, so
the lines idle high on boards that do not fit external pull-ups.
Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/sm8550.dtsi | 26 ++++++++++++++++++++++++++
1 file changed, 26 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 912525e9bca6..165c0248da53 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -1084,6 +1084,24 @@ &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ACTIVE_ONLY>,
status = "disabled";
};
+ uart11: serial@88c000 {
+ compatible = "qcom,geni-uart";
+ reg = <0 0x0088c000 0 0x4000>;
+ clock-names = "se";
+ clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
+ interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH 0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&qup_uart11_default>;
+ interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
+ &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
+ <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
+ &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ACTIVE_ONLY>;
+ interconnect-names = "qup-core", "qup-config";
+ operating-points-v2 = <&qup_opp_table_120mhz>;
+ power-domains = <&rpmhpd RPMHPD_CX>;
+ status = "disabled";
+ };
+
i2c12: i2c@890000 {
compatible = "qcom,geni-i2c";
reg = <0 0x00890000 0 0x4000>;
@@ -5102,6 +5120,14 @@ qup_uart7_default: qup-uart7-default-state {
bias-disable;
};
+ qup_uart11_default: qup-uart11-default-state {
+ /* TX, RX */
+ pins = "gpio70", "gpio71";
+ function = "qup2_se3";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
qup_uart14_default: qup-uart14-default-state {
/* TX, RX */
pins = "gpio78", "gpio79";
--
2.55.0
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v4 3/3] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console
2026-07-22 7:36 [PATCH v4 0/3] arm64: qcom: add Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
2026-07-22 7:36 ` [PATCH v4 1/3] dt-bindings: arm: qcom: document the Ayaneo Pocket DS Alexandre Hamamdjian via B4 Relay
2026-07-22 7:36 ` [PATCH v4 2/3] arm64: dts: qcom: sm8550: add UART11 node Alexandre Hamamdjian via B4 Relay
@ 2026-07-22 7:36 ` Alexandre Hamamdjian via B4 Relay
2026-07-22 7:53 ` sashiko-bot
2 siblings, 1 reply; 5+ messages in thread
From: Alexandre Hamamdjian via B4 Relay @ 2026-07-22 7:36 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Alexandre Hamamdjian,
Teguh Sobirin
From: Teguh Sobirin <teguh@sobir.in>
Add initial Device Tree for the Ayaneo Pocket DS gaming console based
on the Qualcomm QCS8550 platform.
The design is similar to a phone without the modem: game controls are
exposed through a Renesas uPD720201 PCIe USB 3.0 host controller hung
off PCIe1, while a dedicated gamepad MCU is reached over UART11.
DisplayPort is muxed over the USB-C connector with all four lanes
wired, with an ON Semi NB7VPQ904M redriver handling SS and SBU AUX
muxing.
Only the basics are wired up at this stage (boot to console, core
peripherals, USB-C and DP, microSD, WiFi/BT, gaming controls); DSI
panel support will follow in a later submission once the panel
bindings are reviewed.
The FT5426 touchscreen on i2c4 clock-stretches past the GENI
controller's timeout at 400 kHz. The qcom-geni-i2c controller
implements no i2c_bus_recovery, so a stuck SCL can only be cleared by
an FSM reset, which is itself the operation that times out. i2c4 is
therefore run at 100 kHz, well within the FT5426's clock-stretch
tolerance and with ample bandwidth for its sub-256-byte reports.
PCIe0 hosts the WCN7850 WiFi and is pinned to Gen2 (max-link-speed =
<2>), the link speed validated on this board.
sdhc_2 sets qcom,dll-config to 0x0007442c, the DLL_CONFIG value the
QCS8550 vendor device tree ships for this SDCC2 instance, in place of
the generic sm8550 default of 0x0007642c; the vendor value is the one
validated for SDR104 operation on this board.
The board uses the &thermal_cpuss[0-3], &thermal_cpu7_top and
&thermal_gpuss[0-7] labels to extend the SoC thermal zones with an
active trip point and a cooling map driving the on-board PWM fan;
those labels are added to sm8550.dtsi as part of this change so the
board has a real user from the same patch.
Signed-off-by: Teguh Sobirin <teguh@sobir.in>
Co-developed-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
---
arch/arm64/boot/dts/qcom/Makefile | 1 +
.../boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts | 1617 ++++++++++++++++++++
arch/arm64/boot/dts/qcom/sm8550.dtsi | 26 +-
3 files changed, 1631 insertions(+), 13 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index cc42829f92eb..81abb05529ec 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -185,6 +185,7 @@ qcs8300-ride-el2-dtbs := qcs8300-ride.dtb monaco-el2.dtbo
dtb-$(CONFIG_ARCH_QCOM) += qcs8300-ride-el2.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
+dtb-$(CONFIG_ARCH_QCOM) += qcs8550-ayaneo-pocket-ds.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb
diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts
new file mode 100644
index 000000000000..bc9232fd4b71
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-ds.dts
@@ -0,0 +1,1617 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2025, Teguh Sobirin.
+ * Copyright (c) 2025, ROCKNIX (https://github.com/ROCKNIX)
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+#include "qcs8550.dtsi"
+#include "pm8550.dtsi"
+#include "pm8550b.dtsi"
+#define PMK8550VE_SID 5
+#include "pm8550ve.dtsi"
+#include "pm8550vs.dtsi"
+#include "pmk8550.dtsi"
+
+/delete-node/ &aop_image_mem;
+/delete-node/ &aop_config_mem;
+/delete-node/ &camera_mem;
+/delete-node/ &ipa_fw_mem;
+/delete-node/ &ipa_gsi_mem;
+/delete-node/ &mpss_dsm_mem;
+/delete-node/ &mpss_mem;
+/delete-node/ &q6_mpss_dtb_mem;
+/delete-node/ &cdsp_mem;
+/delete-node/ &q6_cdsp_dtb_mem;
+
+/ {
+ model = "AYANEO Pocket DS";
+ compatible = "ayaneo,pocket-ds", "qcom,qcs8550", "qcom,sm8550";
+
+ aliases {
+ serial0 = &uart7;
+ serial1 = &uart14;
+ hsuart0 = &uart11;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+
+ pinctrl-0 = <&volume_up_n>;
+ pinctrl-names = "default";
+
+ key-volume-up {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
+ debounce-interval = <15>;
+ };
+ };
+
+ pmic-glink {
+ compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
+
+ connector@0 {
+ compatible = "usb-c-connector";
+
+ reg = <0>;
+
+ power-role = "dual";
+ data-role = "dual";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ pmic_glink_hs_in: endpoint {
+ remote-endpoint = <&usb_1_dwc3_hs>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ pmic_glink_ss_in: endpoint {
+ remote-endpoint = <&redriver_ss_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_sbu: endpoint {
+ remote-endpoint = <&redriver_sbu>;
+ };
+ };
+ };
+ };
+ };
+
+ pwm_fan: pwm-fan {
+ compatible = "pwm-fan";
+
+ pinctrl-0 = <&fan_pwm_active>, <&fan_int>;
+ pinctrl-1 = <&fan_pwm_sleep>, <&fan_int>;
+ pinctrl-names = "default", "sleep";
+
+ fan-supply = <&vdd_fan_5v0>;
+ pwms = <&pm8550_pwm 3 40000>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <64 IRQ_TYPE_EDGE_FALLING>;
+
+ #cooling-cells = <2>;
+ cooling-levels = <0 30 45 60 70 90 120 150>;
+ };
+
+ reserved-memory {
+ hyp_mem: hyp-region@80000000 {
+ reg = <0 0x80000000 0 0xa00000>;
+ no-map;
+ };
+
+ cpusys_vm_mem: cpusys-vm-region@80a00000 {
+ reg = <0 0x80a00000 0 0x400000>;
+ no-map;
+ };
+
+ hyp_tags_mem: hyp-tags-region@80e00000 {
+ reg = <0 0x80e00000 0 0x3d0000>;
+ no-map;
+ };
+
+ xbl_sc_mem: xbl-sc-region@d8100000 {
+ reg = <0 0xd8100000 0 0x40000>;
+ no-map;
+ };
+
+ hyp_tags_reserved_mem: hyp-tags-reserved-region@811d0000 {
+ reg = <0 0x811d0000 0 0x30000>;
+ no-map;
+ };
+
+ xbl_dt_log_merged_mem: xbl-dt-log-merged-region@81a00000 {
+ reg = <0 0x81a00000 0 0x260000>;
+ no-map;
+ };
+
+ aop_config_merged_mem: aop-config-merged-region@81c80000 {
+ reg = <0 0x81c80000 0 0x74000>;
+ no-map;
+ };
+
+ chipinfo_mem: chipinfo-region@81cf4000 {
+ reg = <0 0x81cf4000 0 0x1000>;
+ no-map;
+ };
+
+ global_sync_mem: global-sync-region@82600000 {
+ reg = <0 0x82600000 0 0x100000>;
+ no-map;
+ };
+
+ tz_stat_mem: tz-stat-region@82700000 {
+ reg = <0 0x82700000 0 0x100000>;
+ no-map;
+ };
+
+ cpucp_fw_mem: cpucp-fw-region@d8140000 {
+ reg = <0 0xd8140000 0 0x1c0000>;
+ no-map;
+ };
+
+ qtee_mem: qtee-region@d8300000 {
+ reg = <0 0xd8300000 0 0x500000>;
+ no-map;
+ };
+
+ hwfence_shbuf: hwfence-shbuf-region@e6440000 {
+ reg = <0 0xe6440000 0 0x2dd000>;
+ no-map;
+ };
+
+ hyp_ext_reserved_mem: hyp-ext-reserved-region@ff700000 {
+ reg = <0 0xff700000 0 0x100000>;
+ no-map;
+ };
+
+ llcc_lpi_mem: llcc-lpi-region@ff800000 {
+ reg = <0 0xff800000 0 0x600000>;
+ no-map;
+ };
+
+ hyp_ext_tags_mem: hyp-ext-tags-region@fce00000 {
+ reg = <0 0xfce00000 0 0x2900000>;
+ no-map;
+ };
+
+ splash_region: splash-region@b8000000 {
+ reg = <0x0 0xb8000000 0x0 0x2b00000>;
+ no-map;
+ };
+ };
+
+ sound {
+ compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
+ model = "SM8550-APS";
+
+ audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
+ "SpkrRight IN", "WSA_SPK2 OUT";
+
+ wsa-dai-link {
+ link-name = "WSA Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&spk_amp_l>,
+ <&spk_amp_r>,
+ <&swr0 0>,
+ <&lpass_wsamacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ va-dai-link {
+ link-name = "VA Capture";
+
+ cpu {
+ sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+ };
+
+ codec {
+ sound-dai = <&lpass_vamacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+ };
+
+ tca6424_vcc: tca6424-vcc-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "tca6424_vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&tlmm 168 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ upd720201_avdd33_reg: upd720201-avdd33-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "upd720201_avdd33";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&tlmm 10 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ vin-supply = <&vph_pwr>;
+
+ pinctrl-0 = <&upd720201_avdd33>;
+ pinctrl-names = "default";
+ };
+
+ upd720201_vdd10_reg: upd720201-vdd10-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "upd720201_vdd10";
+ regulator-min-microvolt = <1050000>;
+ regulator-max-microvolt = <1050000>;
+
+ gpios = <&tlmm 13 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ vin-supply = <&vph_pwr>;
+
+ pinctrl-0 = <&upd720201_vdd10>;
+ pinctrl-names = "default";
+ };
+
+ upd720201_vdd33_reg: upd720201-vdd33-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "upd720201_vdd33";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ vin-supply = <&vph_pwr>;
+
+ pinctrl-0 = <&upd720201_vdd33>;
+ pinctrl-names = "default";
+ };
+
+ vdd_fan_5v0: vdd-fan-5v0-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vdd_fan_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+
+ gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&fan_pwr_active>;
+ pinctrl-names = "default";
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_ts: vdd-ts-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vdd_ts_en";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&tca6408 1 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "vph_pwr";
+ regulator-min-microvolt = <3700000>;
+ regulator-max-microvolt = <3700000>;
+
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ wcn7850-pmu {
+ compatible = "qcom,wcn7850-pmu";
+
+ pinctrl-0 = <&wlan_en>, <&bt_default>, <&pmk8550_sleep_clk>;
+ pinctrl-names = "default";
+
+ wlan-enable-gpios = <&tlmm 80 GPIO_ACTIVE_HIGH>;
+ bt-enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
+
+ vdd-supply = <&vreg_s5g_0p85>;
+ vddio-supply = <&vreg_l15b_1p8>;
+ vddaon-supply = <&vreg_s2g_0p85>;
+ vdddig-supply = <&vreg_s4e_0p95>;
+ vddrfa1p2-supply = <&vreg_s4g_1p25>;
+ vddrfa1p8-supply = <&vreg_s6g_1p86>;
+
+ regulators {
+ vreg_pmu_rfa_cmn: ldo0 {
+ regulator-name = "vreg_pmu_rfa_cmn";
+ };
+
+ vreg_pmu_aon_0p59: ldo1 {
+ regulator-name = "vreg_pmu_aon_0p59";
+ };
+
+ vreg_pmu_wlcx_0p8: ldo2 {
+ regulator-name = "vreg_pmu_wlcx_0p8";
+ };
+
+ vreg_pmu_wlmx_0p85: ldo3 {
+ regulator-name = "vreg_pmu_wlmx_0p85";
+ };
+
+ vreg_pmu_btcmx_0p85: ldo4 {
+ regulator-name = "vreg_pmu_btcmx_0p85";
+ };
+
+ vreg_pmu_rfa_0p8: ldo5 {
+ regulator-name = "vreg_pmu_rfa_0p8";
+ };
+
+ vreg_pmu_rfa_1p2: ldo6 {
+ regulator-name = "vreg_pmu_rfa_1p2";
+ };
+
+ vreg_pmu_rfa_1p8: ldo7 {
+ regulator-name = "vreg_pmu_rfa_1p8";
+ };
+
+ vreg_pmu_pcie_0p9: ldo8 {
+ regulator-name = "vreg_pmu_pcie_0p9";
+ };
+
+ vreg_pmu_pcie_1p8: ldo9 {
+ regulator-name = "vreg_pmu_pcie_1p8";
+ };
+ };
+ };
+};
+
+&apps_rsc {
+ regulators-0 {
+ compatible = "qcom,pm8550-rpmh-regulators";
+ qcom,pmic-id = "b";
+
+ vdd-bob1-supply = <&vph_pwr>;
+ vdd-bob2-supply = <&vph_pwr>;
+ vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>;
+ vdd-l2-l13-l14-supply = <&vreg_bob1>;
+ vdd-l3-supply = <&vreg_s4g_1p25>;
+ vdd-l5-l16-supply = <&vreg_bob1>;
+ vdd-l6-l7-supply = <&vreg_bob1>;
+ vdd-l8-l9-supply = <&vreg_bob1>;
+ vdd-l11-supply = <&vreg_s4g_1p25>;
+ vdd-l12-supply = <&vreg_s6g_1p86>;
+ vdd-l15-supply = <&vreg_s6g_1p86>;
+ vdd-l17-supply = <&vreg_bob2>;
+
+ vreg_bob1: bob1 {
+ regulator-name = "vreg_bob1";
+ regulator-min-microvolt = <3296000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_bob2: bob2 {
+ regulator-name = "vreg_bob2";
+ regulator-min-microvolt = <2720000>;
+ regulator-max-microvolt = <3960000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2b_3p0: ldo2 {
+ regulator-name = "vreg_l2b_3p0";
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l5b_3p1: ldo5 {
+ regulator-name = "vreg_l5b_3p1";
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3104000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l6b_1p8: ldo6 {
+ regulator-name = "vreg_l6b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l7b_1p8: ldo7 {
+ regulator-name = "vreg_l7b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l8b_1p8: ldo8 {
+ regulator-name = "vreg_l8b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l9b_2p9: ldo9 {
+ regulator-name = "vreg_l9b_2p9";
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <3008000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l10b_1p8: ldo10 {
+ regulator-name = "vreg_l10b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l11b_1p2: ldo11 {
+ regulator-name = "vreg_l11b_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l12b_1p8: ldo12 {
+ regulator-name = "vreg_l12b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l13b_3p0: ldo13 {
+ regulator-name = "vreg_l13b_3p0";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l14b_3p2: ldo14 {
+ regulator-name = "vreg_l14b_3p2";
+ regulator-min-microvolt = <3200000>;
+ regulator-max-microvolt = <3200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l15b_1p8: ldo15 {
+ regulator-name = "vreg_l15b_1p8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l16b_2p8: ldo16 {
+ regulator-name = "vreg_l16b_2p8";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l17b_2p5: ldo17 {
+ regulator-name = "vreg_l17b_2p5";
+ regulator-min-microvolt = <2504000>;
+ regulator-max-microvolt = <2504000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-1 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "c";
+
+ vdd-l1-supply = <&vreg_s4g_1p25>;
+ vdd-l2-supply = <&vreg_s4e_0p95>;
+ vdd-l3-supply = <&vreg_s4e_0p95>;
+
+ vreg_l3c_0p9: ldo3 {
+ regulator-name = "vreg_l3c_0p9";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-2 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "d";
+
+ vdd-l1-supply = <&vreg_s4e_0p95>;
+ vdd-l2-supply = <&vreg_s4e_0p95>;
+ vdd-l3-supply = <&vreg_s4e_0p95>;
+
+ vreg_l1d_0p88: ldo1 {
+ regulator-name = "vreg_l1d_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <920000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-3 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "e";
+
+ vdd-l1-supply = <&vreg_s4e_0p95>;
+ vdd-l2-supply = <&vreg_s4e_0p95>;
+ vdd-l3-supply = <&vreg_s4g_1p25>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+
+ vreg_s4e_0p95: smps4 {
+ regulator-name = "vreg_s4e_0p95";
+ regulator-min-microvolt = <904000>;
+ regulator-max-microvolt = <984000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5e_1p08: smps5 {
+ regulator-name = "vreg_s5e_1p08";
+ regulator-min-microvolt = <1010000>;
+ regulator-max-microvolt = <1120000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1e_0p88: ldo1 {
+ regulator-name = "vreg_l1e_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2e_0p9: ldo2 {
+ regulator-name = "vreg_l2e_0p9";
+ regulator-min-microvolt = <904000>;
+ regulator-max-microvolt = <970000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3e_1p2: ldo3 {
+ regulator-name = "vreg_l3e_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-4 {
+ compatible = "qcom,pm8550ve-rpmh-regulators";
+ qcom,pmic-id = "f";
+
+ vdd-l1-supply = <&vreg_s4e_0p95>;
+ vdd-l2-supply = <&vreg_s4e_0p95>;
+ vdd-l3-supply = <&vreg_s4e_0p95>;
+ vdd-s4-supply = <&vph_pwr>;
+
+ vreg_s4f_0p5: smps4 {
+ regulator-name = "vreg_s4f_0p5";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <700000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1f_0p9: ldo1 {
+ regulator-name = "vreg_l1f_0p9";
+ regulator-min-microvolt = <912000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l2f_0p88: ldo2 {
+ regulator-name = "vreg_l2f_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3f_0p88: ldo3 {
+ regulator-name = "vreg_l3f_0p88";
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <912000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+
+ regulators-5 {
+ compatible = "qcom,pm8550vs-rpmh-regulators";
+ qcom,pmic-id = "g";
+
+ vdd-l1-supply = <&vreg_s4g_1p25>;
+ vdd-l2-supply = <&vreg_s4g_1p25>;
+ vdd-l3-supply = <&vreg_s4g_1p25>;
+ vdd-s1-supply = <&vph_pwr>;
+ vdd-s2-supply = <&vph_pwr>;
+ vdd-s3-supply = <&vph_pwr>;
+ vdd-s4-supply = <&vph_pwr>;
+ vdd-s5-supply = <&vph_pwr>;
+ vdd-s6-supply = <&vph_pwr>;
+
+ vreg_s1g_1p25: smps1 {
+ regulator-name = "vreg_s1g_1p25";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s2g_0p85: smps2 {
+ regulator-name = "vreg_s2g_0p85";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s3g_0p8: smps3 {
+ regulator-name = "vreg_s3g_0p8";
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s4g_1p25: smps4 {
+ regulator-name = "vreg_s4g_1p25";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1352000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s5g_0p85: smps5 {
+ regulator-name = "vreg_s5g_0p85";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <1004000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_s6g_1p86: smps6 {
+ regulator-name = "vreg_s6g_1p86";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l1g_1p2: ldo1 {
+ regulator-name = "vreg_l1g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+
+ vreg_l3g_1p2: ldo3 {
+ regulator-name = "vreg_l3g_1p2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+ regulator-allow-set-load;
+ regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
+ RPMH_REGULATOR_MODE_HPM>;
+ };
+ };
+};
+
+&gpi_dma1 {
+ status = "okay";
+};
+
+&gpi_dma2 {
+ status = "okay";
+};
+
+&gpu {
+ status = "okay";
+};
+
+&gpu_zap_shader {
+ firmware-name = "qcom/sm8550/a740_zap.mbn";
+};
+
+&i2c0 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ tca6408: gpio@20 {
+ compatible = "ti,tca6408";
+ reg = <0x20>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ vcc-supply = <&tca6424_vcc>;
+ };
+};
+
+&i2c2 {
+ clock-frequency = <400000>;
+
+ status = "okay";
+
+ touchscreen@5d {
+ compatible = "goodix,gt911";
+ reg = <0x5d>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
+
+ reset-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>;
+ irq-gpios = <&tlmm 39 GPIO_ACTIVE_HIGH>;
+
+ VDDIO-supply = <&vdd_ts>;
+
+ pinctrl-0 = <&ts2_reset>, <&ts2_irq>;
+ pinctrl-names = "default";
+
+ touchscreen-size-x = <768>;
+ touchscreen-size-y = <1024>;
+ };
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+
+ status = "okay";
+
+ touchscreen: touchscreen@38 {
+ compatible = "focaltech,ft5426";
+ reg = <0x38>;
+
+ interrupt-parent = <&tlmm>;
+ interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
+
+ reset-gpios = <&tlmm 24 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l14b_3p2>;
+ iovcc-supply = <&vreg_l12b_1p8>;
+
+ pinctrl-0 = <&ts_int_default &ts_rst_default>;
+ pinctrl-1 = <&ts_int_sleep &ts_rst_sleep>;
+ pinctrl-names = "default", "sleep";
+
+ touchscreen-size-x = <1080>;
+ touchscreen-size-y = <1920>;
+ };
+};
+
+&i2c_hub_2 {
+ status = "okay";
+
+ typec-retimer@1c {
+ compatible = "onnn,nb7vpq904m";
+ reg = <0x1c>;
+
+ vcc-supply = <&vreg_l15b_1p8>;
+
+ retimer-switch;
+ orientation-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ redriver_ss_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ redriver_ss_in: endpoint {
+ data-lanes = <3 2 1 0>;
+ remote-endpoint = <&usb_dp_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ redriver_sbu: endpoint {
+ remote-endpoint = <&pmic_glink_sbu>;
+ };
+ };
+ };
+ };
+};
+
+&i2c_master_hub_0 {
+ status = "okay";
+};
+
+&iris {
+ status = "okay";
+};
+
+/* DMIC 01 23 */
+&lpass_vamacro {
+ pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+ pinctrl-names = "default";
+
+ vdd-micb-supply = <&vreg_l10b_1p8>;
+
+ qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dp0 {
+ status = "okay";
+};
+
+&mdss_dp0_out {
+ data-lanes = <0 1 2 3>;
+};
+
+&pcie0 {
+ wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
+
+ max-link-speed = <2>;
+
+ pinctrl-0 = <&pcie0_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
+&pcie0_phy {
+ vdda-phy-supply = <&vreg_l1e_0p88>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+
+ status = "okay";
+};
+
+&pcie1 {
+ wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
+ perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&pcie1_default_state>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ pcie@0 {
+ /* Renesas μPD720201 PCIe USB3.0 HOST CONTROLLER */
+ usb-controller@0 {
+ compatible = "pci1912,0014";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ avdd33-supply = <&upd720201_avdd33_reg>;
+ vdd10-supply = <&upd720201_vdd10_reg>;
+ vdd33-supply = <&upd720201_vdd33_reg>;
+
+ pinctrl-0 = <&gamepad_pwr_en>;
+ pinctrl-names = "default";
+ };
+ };
+};
+
+&pcie1_phy {
+ vdda-phy-supply = <&vreg_l3c_0p9>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+ vdda-qref-supply = <&vreg_l1e_0p88>;
+
+ status = "okay";
+};
+
+&pcieport0 {
+ wifi@0 {
+ compatible = "pci17cb,1107";
+ reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+ vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+ vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+ };
+};
+
+&pon_pwrkey {
+ status = "okay";
+};
+
+&pon_resin {
+ linux,code = <KEY_VOLUMEDOWN>;
+
+ status = "okay";
+};
+
+&pm8550_gpios {
+ sdc2_card_det_n: sdc2-card-det-n-state {
+ pins = "gpio12";
+ function = "normal";
+ input-enable;
+ output-disable;
+ bias-pull-up;
+ power-source = <1>;
+ };
+
+ volume_up_n: volume-up-n-state {
+ pins = "gpio6";
+ function = "normal";
+ power-source = <1>;
+ bias-pull-up;
+ input-enable;
+ };
+
+ fan_pwm_active: fan-pwm-active-state {
+ pins = "gpio9";
+ function = "func1";
+ output-low;
+ bias-disable;
+ power-source = <0>;
+ qcom,drive-strength = <3>; /* PMIC_GPIO_STRENGTH_LOW */
+ };
+
+ fan_pwm_sleep: fan-pwm-sleep-state {
+ pins = "gpio9";
+ function = "normal";
+ output-high;
+ bias-disable;
+ power-source = <0>;
+ qcom,drive-strength = <3>; /* PMIC_GPIO_STRENGTH_LOW */
+ };
+};
+
+&pm8550_pwm {
+ status = "okay";
+};
+
+&pm8550b_eusb2_repeater {
+ vdd18-supply = <&vreg_l15b_1p8>;
+ vdd3-supply = <&vreg_l5b_3p1>;
+};
+
+&pmk8550_gpios {
+ pmk8550_sleep_clk: sleep-clk-state {
+ pins = "gpio3";
+ function = "func1";
+ input-disable;
+ output-enable;
+ bias-disable;
+ power-source = <0>;
+ };
+};
+
+&pmk8550_rtc {
+ nvmem-cells = <&rtc_offset>;
+ nvmem-cell-names = "offset";
+};
+
+&pmk8550_sdam_2 {
+ rtc_offset: rtc-offset@bc {
+ reg = <0xbc 0x4>;
+ };
+};
+
+&qupv3_id_0 {
+ status = "okay";
+};
+
+&qupv3_id_1 {
+ status = "okay";
+};
+
+&remoteproc_adsp {
+ firmware-name = "qcom/sm8550/ayaneo/adsp.mbn",
+ "qcom/sm8550/ayaneo/adsp_dtb.mbn";
+
+ status = "okay";
+};
+
+&remoteproc_cdsp {
+ /delete-property/ memory-region;
+};
+
+&remoteproc_mpss {
+ /delete-property/ memory-region;
+};
+
+&sdhc_2 {
+ cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
+
+ pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+ pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+ pinctrl-names = "default", "sleep";
+
+ vmmc-supply = <&vreg_l9b_2p9>;
+ vqmmc-supply = <&vreg_l8b_1p8>;
+
+ no-sdio;
+ no-mmc;
+
+ sd-uhs-sdr12;
+ sd-uhs-sdr25;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ sd-uhs-ddr50;
+
+ qcom,dll-config = <0x0007442c>;
+
+ status = "okay";
+};
+
+&sleep_clk {
+ clock-frequency = <32764>;
+};
+
+&swr0 {
+ status = "okay";
+
+ spk_amp_l: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+
+ pinctrl-0 = <&spkr_1_sd_n_active>;
+ pinctrl-names = "default";
+
+ powerdown-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
+
+ vdd-1p8-supply = <&vreg_l10b_1p8>;
+ vdd-io-supply = <&vreg_l10b_1p8>;
+
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrLeft";
+ qcom,port-mapping = <1 2 3 7 10 13>;
+ };
+
+ spk_amp_r: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+
+ pinctrl-0 = <&spkr_2_sd_n_active>;
+ pinctrl-names = "default";
+
+ powerdown-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
+
+ vdd-1p8-supply = <&vreg_l10b_1p8>;
+ vdd-io-supply = <&vreg_l10b_1p8>;
+
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrRight";
+ qcom,port-mapping = <4 5 6 7 11 13>;
+ };
+};
+
+&thermal_cpu7_top {
+ trips {
+ cpu7_active: cpu7-active {
+ temperature = <50000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&cpu7_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_cpuss0 {
+ trips {
+ cpuss0_active: cpuss0-active {
+ temperature = <50000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&cpuss0_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_cpuss1 {
+ trips {
+ cpuss1_active: cpuss1-active {
+ temperature = <50000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&cpuss1_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_cpuss2 {
+ trips {
+ cpuss2_active: cpuss2-active {
+ temperature = <50000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&cpuss2_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_cpuss3 {
+ trips {
+ cpuss3_active: cpuss3-active {
+ temperature = <50000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&cpuss3_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_gpuss0 {
+ trips {
+ gpuss0_active: gpuss0-active {
+ temperature = <55000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&gpuss0_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_gpuss1 {
+ trips {
+ gpuss1_active: gpuss1-active {
+ temperature = <55000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&gpuss1_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_gpuss2 {
+ trips {
+ gpuss2_active: gpuss2-active {
+ temperature = <55000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&gpuss2_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_gpuss3 {
+ trips {
+ gpuss3_active: gpuss3-active {
+ temperature = <55000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&gpuss3_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_gpuss4 {
+ trips {
+ gpuss4_active: gpuss4-active {
+ temperature = <55000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&gpuss4_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_gpuss5 {
+ trips {
+ gpuss5_active: gpuss5-active {
+ temperature = <55000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&gpuss5_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_gpuss6 {
+ trips {
+ gpuss6_active: gpuss6-active {
+ temperature = <55000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&gpuss6_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&thermal_gpuss7 {
+ trips {
+ gpuss7_active: gpuss7-active {
+ temperature = <55000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ };
+
+ cooling-maps {
+ map {
+ trip = <&gpuss7_active>;
+ cooling-device = <&pwm_fan THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ };
+ };
+};
+
+&tlmm {
+ gpio-reserved-ranges = <32 4>;
+
+ bt_default: bt-default-state {
+ bt-en-pins {
+ pins = "gpio81";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ sw-ctrl-pins {
+ pins = "gpio82";
+ function = "gpio";
+ bias-pull-down;
+ };
+ };
+
+ fan_pwr_active: fan-pwr-active-state {
+ pins = "gpio31";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ output-low;
+ };
+
+ fan_int: fan-int-state {
+ pins = "gpio64";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ upd720201_avdd33: upd720201-avdd33-state {
+ pins = "gpio10";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ upd720201_vdd10: upd720201-vdd10-state {
+ pins = "gpio13";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ upd720201_vdd33: upd720201-vdd33-state {
+ pins = "gpio18";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ gamepad_pwr_en: gamepad-pwr-en-active-state {
+ pins = "gpio52";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ wlan_en: wlan-en-state {
+ pins = "gpio80";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+
+ spkr_1_sd_n_active: spkr-1-sd-n-active-state {
+ pins = "gpio7";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ spkr_2_sd_n_active: spkr-2-sd-n-active-state {
+ pins = "gpio12";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ ts_rst_default: ts-rst-default-state {
+ pins = "gpio24";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
+ ts_rst_sleep: ts-rst-sleep-state {
+ pins = "gpio24";
+ function = "gpio";
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+
+ ts_int_default: ts-int-default-state {
+ pins = "gpio25";
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <8>;
+ };
+
+ ts_int_sleep: ts-int-sleep-state {
+ pins = "gpio25";
+ function = "gpio";
+ bias-pull-down;
+ drive-strength = <2>;
+ };
+
+ ts2_irq: ts2-irq-state {
+ pins = "gpio39";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-disable;
+ };
+
+ ts2_reset: ts2-reset-state {
+ pins = "gpio38";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-down;
+ };
+};
+
+&uart7 {
+ status = "okay";
+};
+
+/* AYANEO Controller serial interface */
+&uart11 {
+ status = "okay";
+};
+
+&uart14 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn7850-bt";
+
+ vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+ vddaon-supply = <&vreg_pmu_aon_0p59>;
+ vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+ vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+ vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+ vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+ vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+
+ max-speed = <3200000>;
+ };
+};
+
+&ufs_mem_hc {
+ reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
+
+ vcc-supply = <&vreg_l17b_2p5>;
+ vcc-max-microamp = <1300000>;
+ vccq-supply = <&vreg_l1g_1p2>;
+ vccq-max-microamp = <1200000>;
+ vdd-hba-supply = <&vreg_l3g_1p2>;
+
+ status = "okay";
+};
+
+&ufs_mem_phy {
+ vdda-phy-supply = <&vreg_l1d_0p88>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+
+ status = "okay";
+};
+
+&usb_1 {
+ status = "okay";
+};
+
+&usb_1_dwc3_hs {
+ remote-endpoint = <&pmic_glink_hs_in>;
+};
+
+&usb_1_hsphy {
+ vdd-supply = <&vreg_l1e_0p88>;
+ vdda12-supply = <&vreg_l3e_1p2>;
+
+ phys = <&pm8550b_eusb2_repeater>;
+
+ status = "okay";
+};
+
+&usb_dp_qmpphy {
+ vdda-phy-supply = <&vreg_l3e_1p2>;
+ vdda-pll-supply = <&vreg_l3f_0p88>;
+
+ status = "okay";
+};
+
+&usb_dp_qmpphy_out {
+ remote-endpoint = <&redriver_ss_in>;
+};
+
+&xo_board {
+ clock-frequency = <76800000>;
+};
diff --git a/arch/arm64/boot/dts/qcom/sm8550.dtsi b/arch/arm64/boot/dts/qcom/sm8550.dtsi
index 165c0248da53..26797e9668f2 100644
--- a/arch/arm64/boot/dts/qcom/sm8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8550.dtsi
@@ -5790,7 +5790,7 @@ reset-mon-config {
};
};
- cpuss0-thermal {
+ thermal_cpuss0: cpuss0-thermal {
thermal-sensors = <&tsens0 1>;
trips {
@@ -5808,7 +5808,7 @@ reset-mon-config {
};
};
- cpuss1-thermal {
+ thermal_cpuss1: cpuss1-thermal {
thermal-sensors = <&tsens0 2>;
trips {
@@ -5826,7 +5826,7 @@ reset-mon-config {
};
};
- cpuss2-thermal {
+ thermal_cpuss2: cpuss2-thermal {
thermal-sensors = <&tsens0 3>;
trips {
@@ -5844,7 +5844,7 @@ reset-mon-config {
};
};
- cpuss3-thermal {
+ thermal_cpuss3: cpuss3-thermal {
thermal-sensors = <&tsens0 4>;
trips {
@@ -6054,7 +6054,7 @@ cpu6_bottom_crit: cpu-critical {
};
};
- cpu7-top-thermal {
+ thermal_cpu7_top: cpu7-top-thermal {
thermal-sensors = <&tsens0 13>;
trips {
@@ -6562,7 +6562,7 @@ reset-mon-config {
};
};
- gpuss-0-thermal {
+ thermal_gpuss0: gpuss-0-thermal {
polling-delay-passive = <10>;
thermal-sensors = <&tsens2 1>;
@@ -6595,7 +6595,7 @@ trip-point2 {
};
};
- gpuss-1-thermal {
+ thermal_gpuss1: gpuss-1-thermal {
polling-delay-passive = <10>;
thermal-sensors = <&tsens2 2>;
@@ -6628,7 +6628,7 @@ trip-point2 {
};
};
- gpuss-2-thermal {
+ thermal_gpuss2: gpuss-2-thermal {
polling-delay-passive = <10>;
thermal-sensors = <&tsens2 3>;
@@ -6661,7 +6661,7 @@ trip-point2 {
};
};
- gpuss-3-thermal {
+ thermal_gpuss3: gpuss-3-thermal {
polling-delay-passive = <10>;
thermal-sensors = <&tsens2 4>;
@@ -6694,7 +6694,7 @@ trip-point2 {
};
};
- gpuss-4-thermal {
+ thermal_gpuss4: gpuss-4-thermal {
polling-delay-passive = <10>;
thermal-sensors = <&tsens2 5>;
@@ -6727,7 +6727,7 @@ trip-point2 {
};
};
- gpuss-5-thermal {
+ thermal_gpuss5: gpuss-5-thermal {
polling-delay-passive = <10>;
thermal-sensors = <&tsens2 6>;
@@ -6760,7 +6760,7 @@ trip-point2 {
};
};
- gpuss-6-thermal {
+ thermal_gpuss6: gpuss-6-thermal {
polling-delay-passive = <10>;
thermal-sensors = <&tsens2 7>;
@@ -6793,7 +6793,7 @@ trip-point2 {
};
};
- gpuss-7-thermal {
+ thermal_gpuss7: gpuss-7-thermal {
polling-delay-passive = <10>;
thermal-sensors = <&tsens2 8>;
--
2.55.0
^ permalink raw reply related [flat|nested] 5+ messages in thread