* [PATCH 3/3] hwmon: pmbus: add MPQ8646 driver
2026-07-23 13:02 [PATCH 0/3] hwmon: pmbus: add MPS MPQ8646 support Vincent Jardin via B4 Relay
2026-07-23 13:02 ` [PATCH 1/3] hwmon: pmbus: event notification with alarms Vincent Jardin via B4 Relay
2026-07-23 13:02 ` [PATCH 2/3] dt-bindings: hwmon: pmbus: add MPS MPQ8646 binding Vincent Jardin via B4 Relay
@ 2026-07-23 13:02 ` Vincent Jardin via B4 Relay
2026-07-23 13:19 ` sashiko-bot
2 siblings, 1 reply; 11+ messages in thread
From: Vincent Jardin via B4 Relay @ 2026-07-23 13:02 UTC (permalink / raw)
To: Guenter Roeck, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Jonathan Corbet, Shuah Khan
Cc: linux-hwmon, linux-kernel, devicetree, linux-doc, Vincent Jardin
From: Vincent Jardin <vjardin@free.fr>
Add a new single-chip driver for the MPS MPQ8646 that is
a PMBus device.
Beyond basic PMBus telemetry, the driver adds:
- MFR_CFG_EXT gate-close retry after CLEAR_LAST_FAULT.
- alarm acknowledge via inX_reset_history.
- STATUS_WORD MPS-extended bit decode + post-mortem clear.
- In-driver alarm-poll fallback work item (thanks lm90) for
boards without SMBALERT
- on_off_config/vout_margin/mfr_pmbus_lock sysfs.
Signed-off-by: Vincent Jardin <vjardin@free.fr>
---
Documentation/hwmon/mpq8646.rst | 314 ++++++++++
MAINTAINERS | 8 +
drivers/hwmon/pmbus/Kconfig | 11 +
drivers/hwmon/pmbus/Makefile | 1 +
drivers/hwmon/pmbus/mpq8646.c | 1214 +++++++++++++++++++++++++++++++++++++++
5 files changed, 1548 insertions(+)
diff --git a/Documentation/hwmon/mpq8646.rst b/Documentation/hwmon/mpq8646.rst
new file mode 100644
index 000000000000..61ca2a5387da
--- /dev/null
+++ b/Documentation/hwmon/mpq8646.rst
@@ -0,0 +1,314 @@
+.. SPDX-License-Identifier: GPL-2.0-only
+.. Copyright (c) 2026 Free Mobile - Vincent Jardin <vjardin@free.fr>
+
+Kernel driver mpq8646
+=====================
+
+Supported chips:
+
+ * MPS MPQ8646
+
+ Prefix: 'mpq8646'
+
+Author:
+ - Vincent Jardin <vjardin@free.fr>
+
+Chip-identity
+-------------
+
+Support the boards that are designed with the MPS MPQ8646 probed thanks
+to``MFR_MODEL`` register.
+
+This driver targets the MPQ8646 silicon specifically.
+
+Description
+-----------
+
+The MPQ8646 is a fully integrated, PMBus-compatible, high-frequency,
+synchronous buck converter. It offers a compact solution that
+achieves up high Amps output current per phase, with excellent load
+and line regulation over a wide input supply range. The chip
+operates at high efficiency over a wide output current load range.
+
+The PMBus interface provides converter configurations and key
+parameters monitoring.
+
+The device adopts MPS's proprietary multi-phase digital
+constant-on-time (MCOT) control, which provides fast transient
+response and eases loop stabilization. The MCOT scheme also allows
+multiple devices or channels to be connected in parallel with
+excellent current sharing and phase interleaving for high-current
+applications.
+
+Fully integrated protection features include over-current
+protection (OCP), over-voltage protection (OVP), under-voltage
+protection (UVP), and over-temperature protection (OTP).
+
+This device is compliant with:
+
+- PMBus rev 1.3 interface.
+
+The driver exports the following attributes via the 'sysfs' files
+for input voltage:
+
+- in1_input
+- in1_label
+- in1_max
+- in1_max_alarm
+- in1_min
+- in1_min_alarm
+- in1_crit
+- in1_crit_alarm
+
+The driver provides the following attributes for output voltage:
+
+- in2_input
+- in2_label
+- in2_alarm
+- in2_max
+- in2_max_alarm
+- in2_min
+- in2_min_alarm
+- in2_crit
+- in2_crit_alarm
+- in2_lcrit
+- in2_lcrit_alarm
+
+The driver provides the following attributes for output current:
+
+- curr1_input
+- curr1_label
+- curr1_max
+- curr1_max_alarm
+- curr1_crit
+- curr1_crit_alarm
+
+The driver provides the following attributes for temperature:
+
+- temp1_input
+- temp1_max
+- temp1_max_alarm
+- temp1_crit
+- temp1_crit_alarm
+
+Alarm acknowledgment
+---------------------
+
+The hwmon-class ``inX_alarm``/``currX_alarm``/``tempX_alarm`` files are
+read-only in pmbus_core. The driver exposes the standard
+``PMBUS_VIRT_RESET_*_HISTORY`` virtual-register channel for fault
+acknowledgment: writing ``1`` to ``inX_reset_history`` /
+``currX_reset_history`` / ``tempX_reset_history`` sends the chip a
+``CLEAR_FAULTS`` (0x03) Send-Byte, which clears the latched
+``STATUS_WORD`` / ``STATUS_VOUT`` / ``STATUS_IOUT`` /
+``STATUS_INPUT`` / ``STATUS_TEMPERATURE`` bits the chip is currently
+exposing.
+
+The MPS-specific NVM post-mortem register
+``PROTECTION_LAST`` (0xFB) is not cleared by this path, see the use of the
+``clear_protection_last[_force]`` debugfs entries described below.
+
+Regulator framework integration
+-------------------------------
+
+When ``CONFIG_REGULATOR=y`` is set, the chip is
+exposed under ``/sys/class/regulator/`` and accepts the standard
+regulator framework operations:
+
+- ``regulator_enable()`` / ``regulator_disable()`` -> ``OPERATION`` (0x01)
+- ``regulator_set_voltage()`` -> ``VOUT_COMMAND`` (0x21)
+- ``regulator_get_voltage()`` -> ``READ_VOUT`` (0x8B)
+- ``regulator_is_enabled()`` -> ``OPERATION`` bit-decode
+
+The single regulator descriptor is named ``"vout"`` (page 0). For a
+multi-page configuration the descriptor table can be extended in
+the driver.
+
+In-driver alarm-poll fallback
+-----------------------------
+
+On boards where the chip's ``SMBALERT#`` pin is unavailable to the
+SoC, ``pmbus_core::pmbus_irq_setup`` cannot deliver SMBALERT-driven
+``poll(POLLPRI)`` wakes or ``udev change@...`` events on the
+``inX_alarm`` files. The driver provides a ``delayed_work``-based
+polling fallback (inspired from ``drivers/hwmon/lm90.c``) that
+periodically reads ``STATUS_WORD`` and calls ``hwmon_notify_event()``
+on 0->1 transitions. The frequency of polling is tunable:
+
+::
+
+ /sys/kernel/debug/mpq8646/<bus>-<addr>/alarm_poll_interval_ms
+
+The default is 1000 ms.
+
+Set it to 0 to disable. The worker self-suppresses
+when ``client->irq != 0`` (i.e. when DT supplies an
+``interrupts = <...>`` property on the regulator node), so adding
+``SMBALERT#`` wiring is a zero-driver-change uplift on a future
+board rev.
+
+MPS post-mortem (PROTECTION_LAST)
+---------------------------------
+
+The MPQ8646 silicon keeps a single 16-bit NVM-backed record of the
+last protection event in ``PROTECTION_LAST`` (0xFB). It survives
+chip power/reset. The following debugfs entries expose it:
+
+::
+
+ /sys/kernel/debug/mpq8646/<bus>-<addr>/protection_last (RO)
+ /sys/kernel/debug/mpq8646/<bus>-<addr>/clear_protection_last (WO)
+ /sys/kernel/debug/mpq8646/<bus>-<addr>/clear_protection_last_force (WO)
+ /sys/kernel/debug/mpq8646/<bus>-<addr>/status_decoded (RO)
+
+``protection_last`` decodes the 16-bit value based on the datasheet
+fault names (``INIT_FAULT``, ``NVM_CRC_ERROR``, ``NVM_FAULT``,
+``OC_PHASE_FAULT``, ``OTP_SELF_FAULT``, ``SWITCH_PRD_FAULT``,
+``VIN_OV_FAULT``, ``VOUT_OV_FAULT``, ``VOUT_UV_FAULT``,
+``OC_TOT_FAULT``, ``VIN_UVLO_FAULT``, ``DRMOS_OTP``).
+
+``clear_protection_last`` writes ``CLEAR_LAST_FAULT`` (0x08) Send-Byte.
+The chip silently no-ops unless ``MFR_CFG_EXT`` (0xF5) bit[6] is set.
+
+``clear_protection_last_force`` performs the unlock with the following
+six-step dansing:
+
+1. read ``WRITE_PROTECT`` (0x10) and ``MFR_CFG_EXT`` (0xF5) for restore
+2. clear ``WRITE_PROTECT`` if set
+3. set ``MFR_CFG_EXT`` bit[6] = 1, preserving other bits
+4. send ``CLEAR_LAST_FAULT`` (0x08)
+5. restore ``MFR_CFG_EXT`` (with retry to handle the chip's
+ undocumented post-NVM-write busy window)
+6. restore ``WRITE_PROTECT``
+
+``status_decoded`` reads ``STATUS_WORD`` (0x79) and renders the
+16 bits with MPS-extension labels (bit12 = ``NVM_SUMMARY``,
+bit8 = ``WATCH_DOG``, bit0 = ``DRMOS_FAULT``) instead of the
+PMBus 1.3 spec generic names.
+
+NVMEM snapshot
+--------------
+
+When ``CONFIG_NVMEM=y`` is set, the chip's NVM-backed
+observability registers are exposed as a single 16-byte read-only
+``nvmem_device`` at ``/sys/bus/nvmem/devices/<i2c-name>/nvmem``.
+Layout (little-endian for 16-bit fields, zero-fill on per-entry read
+failure and for the reserved tail):
+
+::
+
+ offset 0..1 PROTECTION_LAST (0xFB) word
+ offset 2..3 MFR_RETRY_TIMES (0xF4) word
+ offset 4..5 MFR_CONFIG_ID (0xC0) word
+ offset 6..7 MFR_VBOOT_CFG (0xFC) word
+ offset 8 MFR_SILICON_REV (0xC3) byte
+ offset 9..15 reserved (zero)
+
+Suitable for single-``cat`` post-mortem capture by a fleet daemon.
+
+Diagnostics and introspection
+-----------------------------
+
+When ``CONFIG_DEBUG_FS=y`` is set, the driver exposes the following
+entries under ``/sys/kernel/debug/mpq8646/<bus>-<addr>/``. Most are diagnostic
+probes; the read/write entries (marked R/W) are direct accessors to
+the underlying chip command.
+
+Identity / observability (read-only):
+
+========================== ================== =================================
+File PMBus / MFR cmd Description
+========================== ================== =================================
+``mfr_config_id`` 0xC0 (word) board / SKU NVM identifier
+``mfr_config_code_rev`` 0xC1 (word) NVM image revision (PART_RECOG +
+ config code rev fields)
+``mfr_silicon_rev`` 0xC3 (byte) die revision
+``mfr_retry_times`` 0xF4 (word) per-fault-class recovery-mode
+ configuration (NOT a retry
+ count). Four 4-bit fields
+ [15:12]=OTP, [11:8]=VOUT_OV,
+ [7:4]=VOUT_UV, [3:0]=OCP.
+ Each field: 0x0=latch-off,
+ 0x1..0xE=retry N times then
+ latch off, 0xF=hiccup
+ (retry indefinitely). The
+ chip exposes no in-NVM
+ retry-event counter; track
+ transitions externally if
+ needed (poll
+ ``protection_last`` or watch
+ ``inX_alarm`` / ``temp1_alarm``
+ ``poll(POLLPRI)`` wakes).
+``mfr_vboot_cfg`` 0xFC (word) ADDR/VBOOT latched at POR
+========================== ================== =================================
+
+Timing / UVLO knobs (read-only):
+
+========================== ================== =================================
+File PMBus cmd Description
+========================== ================== =================================
+``vin_on`` 0x35 (word) UVLO turn-on threshold
+``vin_off`` 0x36 (word) UVLO turn-off threshold
+``ton_delay`` 0x60 (word) soft-start delay
+``ton_rise`` 0x61 (word) soft-start ramp time
+``toff_delay`` 0x64 (word) soft-stop delay
+``toff_fall`` 0x65 (word) soft-stop ramp time
+========================== ================== =================================
+
+Configuration (read/write):
+
+========================== ================== =================================
+File PMBus / MFR cmd Description
+========================== ================== =================================
+``on_off_config`` 0x02 (byte) PMBus vs CTRL-pin on/off source +
+ active polarity
+``vout_margin_high`` 0x25 (word) production margin-high VOUT setpoint
+``vout_margin_low`` 0x26 (word) production margin-low VOUT setpoint
+``mfr_pmbus_lock`` 0xEE (word) programmable PMBus write-lock
+ (independent of WRITE_PROTECT)
+``mfr_product_rev_user`` 0xC2 (word) user-programmable product revision
+``alarm_poll_interval_ms`` -- alarm-poll worker cadence (driver-
+ local, not a chip register)
+========================== ================== =================================
+
+NVM commit / revert (write-only):
+
+========================== ================== =================================
+File PMBus cmd Description
+========================== ================== =================================
+``store_all`` 0x15 STORE_USER_ALL Send-Byte (commit RAM
+ config to chip NVM)
+``restore_all`` 0x16 RESTORE_USER_ALL Send-Byte (revert
+ RAM to last-NVM image)
+========================== ================== =================================
+
+Bring-up probes (write-only triggers, results in ``last_probe``):
+
+========================== ==================================================
+File Action
+========================== ==================================================
+``probe_smbus_rword <reg>`` i2c_smbus_read_word_data on <reg>
+``probe_smbus_rbyte <reg>`` i2c_smbus_read_byte_data on <reg>
+``probe_raw_xfer <reg>`` raw i2c_transfer read-word on <reg>
+``probe_page_write <pg>`` write PMBUS_PAGE = <pg>
+``probe_clear_faults`` send CLEAR_FAULTS (0x03) Send-Byte
+``force_raw_xfer`` if 1, the read_word_data hook uses raw i2c_transfer
+``delay_us`` udelay before each chip-driver hook call
+``stats`` per-hook call / error counters
+``last_probe`` result of the most recent probe_* operation
+``reset_stats`` zero the stats counters
+========================== ==================================================
+
+Devicetree
+----------
+
+The driver uses ``compatible = "mps,mpq8646"``. There are some few optional
+properties:
+
+- ``mps,vout-fb-divider-ratio-permille`` : it writes ``VOUT_SCALE_LOOP``
+ (0x29) at probe to compensate for an external resistor divider in
+ the VOUT feedback path. The valid range is 11-bit.
+- ``interrupts = <...>`` : if the board routes the chip's
+ ``SMBALERT#`` pin to a SoC GPIO, declaring it here lights up
+ ``pmbus_core::pmbus_irq_setup`` and disables the in-driver
+ alarm-poll fallback
diff --git a/MAINTAINERS b/MAINTAINERS
index 1ab8736850ea..f4766a851df5 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18328,6 +18328,14 @@ S: Maintained
F: Documentation/hwmon/mp9945.rst
F: drivers/hwmon/pmbus/mp9945.c
+MPS MPQ8646 PMBUS DRIVER
+M: Vincent Jardin <vjardin@free.fr>
+L: linux-hwmon@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/hwmon/pmbus/mps,mpq8646.yaml
+F: Documentation/hwmon/mpq8646.rst
+F: drivers/hwmon/pmbus/mpq8646.c
+
MR800 AVERMEDIA USB FM RADIO DRIVER
M: Alexey Klimov <alexey.klimov@linaro.org>
L: linux-media@vger.kernel.org
diff --git a/drivers/hwmon/pmbus/Kconfig b/drivers/hwmon/pmbus/Kconfig
index c8cda160b5f8..9f44e76b0b64 100644
--- a/drivers/hwmon/pmbus/Kconfig
+++ b/drivers/hwmon/pmbus/Kconfig
@@ -616,6 +616,17 @@ config SENSORS_MPQ8785
This driver can also be built as a module. If so, the module will
be called mpq8785.
+config SENSORS_MPQ8646
+ tristate "MPS MPQ8646"
+ depends on REGULATOR || !REGULATOR
+ depends on NVMEM || !NVMEM
+ help
+ If you say yes here you get hardware monitoring support for the
+ Monolithic Power Systems MPQ8646.
+
+ This driver can also be built as a module. If so, the module
+ will be called mpq8646.
+
config SENSORS_PIM4328
tristate "Flex PIM4328 and compatibles"
help
diff --git a/drivers/hwmon/pmbus/Makefile b/drivers/hwmon/pmbus/Makefile
index ffc05f493213..6f8fda966600 100644
--- a/drivers/hwmon/pmbus/Makefile
+++ b/drivers/hwmon/pmbus/Makefile
@@ -60,6 +60,7 @@ obj-$(CONFIG_SENSORS_MP9941) += mp9941.o
obj-$(CONFIG_SENSORS_MP9945) += mp9945.o
obj-$(CONFIG_SENSORS_MPQ7932) += mpq7932.o
obj-$(CONFIG_SENSORS_MPQ8785) += mpq8785.o
+obj-$(CONFIG_SENSORS_MPQ8646) += mpq8646.o
obj-$(CONFIG_SENSORS_PLI1209BC) += pli1209bc.o
obj-$(CONFIG_SENSORS_PM6764TR) += pm6764tr.o
obj-$(CONFIG_SENSORS_PXE1610) += pxe1610.o
diff --git a/drivers/hwmon/pmbus/mpq8646.c b/drivers/hwmon/pmbus/mpq8646.c
new file mode 100644
index 000000000000..17096abaaaa7
--- /dev/null
+++ b/drivers/hwmon/pmbus/mpq8646.c
@@ -0,0 +1,1214 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Driver for MPS MPQ8646 step-down converter.
+ *
+ * Copyright (c) 2026 Free Mobile - Vincent Jardin <vjardin@free.fr>
+ */
+
+#include <linux/bitops.h>
+#include <linux/debugfs.h>
+#include <linux/delay.h>
+#include <linux/hwmon.h>
+#include <linux/i2c.h>
+#include <linux/ktime.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/nvmem-provider.h>
+#include <linux/of_device.h>
+#include <linux/pmbus.h>
+#include <linux/property.h>
+#include <linux/regulator/driver.h>
+#include <linux/seq_file.h>
+#include <linux/workqueue.h>
+#include "pmbus.h"
+
+/* Default cadence for the in-driver alarm-poll fallback (ms) */
+#define MPQ8646_ALARM_POLL_MS_DEFAULT 1000
+
+/* MPS vendor-extended command codes (NOT in PMBus 1.3 Part II) */
+#define MPS_CLEAR_LAST_FAULT 0x08
+#define MPS_MFR_CFG_EXT 0xF5
+#define MPS_MFR_CFG_EXT_CLR_LAST_EN BIT(6)
+#define MPS_PROTECTION_LAST 0xFB
+
+/*
+ * PMBus 1.3 NVM commit / revert commands. pmbus.h does not provide
+ * named constants for these. MPS equivalent of STORE_ALL (15h) and
+ * RESTORE_ALL (16h).
+ */
+#define PMBUS_STORE_USER_ALL 0x15
+#define PMBUS_RESTORE_USER_ALL 0x16
+
+/* PMBus 1.3 timing / UVLO command codes that pmbus.h doesn't expose */
+#define PMBUS_VIN_ON 0x35
+#define PMBUS_VIN_OFF 0x36
+#define PMBUS_TON_DELAY 0x60
+#define PMBUS_TON_RISE 0x61
+#define PMBUS_TOFF_DELAY 0x64
+#define PMBUS_TOFF_FALL 0x65
+
+/* MPS vendor-extended observability / identity registers */
+#define MPS_MFR_CONFIG_ID 0xC0
+#define MPS_MFR_CONFIG_CODE_REV 0xC1
+#define MPS_MFR_PRODUCT_REV_USER 0xC2
+#define MPS_MFR_SILICON_REV 0xC3
+#define MPS_MFR_RETRY_TIMES 0xF4
+#define MPS_MFR_VBOOT_CFG 0xFC
+
+/*
+ * MPS_MFR_PMBUS_LOCK (EEh): 16-bit WORD whose low two bits gate
+ * subsequent PMBus writes
+ * bits[1:0] = 00 -- unlocked (POR default)
+ * 01 -- lock all writes EXCEPT VOUT_COMMAND (0x21)
+ * so the operator can still DVFS the rail
+ * 11 -- lock all writes
+ * A negative-going PG edge resets these bits to 00, the lock
+ * is operationally reversible without a full chip POR.
+ */
+#define MPS_MFR_PMBUS_LOCK 0xEE
+
+/*
+ * Retry parameters for the MFR_CFG_EXT gate-close write after
+ * CLEAR_LAST_FAULT. Bench-observed NVM-busy NACK window on this
+ * silicon is about 1 ms; the datasheet does not have information.
+ */
+#define MPQ8646_NVM_RETRY_MAX 5
+#define MPQ8646_NVM_RETRY_DELAY_US_MIN 2000
+#define MPQ8646_NVM_RETRY_DELAY_US_MAX 4000
+
+/*
+ * VOUT_MODE invalid-value sentinel. PMBus chips return all-ones on
+ * unimplemented-register reads (a 0xFF byte is otherwise a legal
+ * encoding for VID mode 0b111, so we treat exactly 0xFF as
+ * "register absent" rather than "valid mode 7").
+ */
+#define PB_VOUT_MODE_INVALID 0xFF
+
+/*
+ * VOUT_MODE byte layout per PMBus 1.3 Part II Table 2:
+ * [7:5] mode (0=LINEAR16, 1=VID, 2=DIRECT, ...)
+ * [4:0] mode-specific parameter (e.g. linear-format exponent)
+ * pmbus.h gives us PB_VOUT_MODE_MODE_MASK (0xE0) and
+ * PB_VOUT_MODE_LINEAR/VID/DIRECT as bit-aligned mask values; we
+ * still need an explicit shift to compare them after a right-shift
+ * to-the-LSB.
+ */
+#define PB_VOUT_MODE_MODE_SHIFT 5
+
+#define MPQ8646_TRACE(fmt, ...) \
+ pr_debug("mpq8646-trace: " fmt, ##__VA_ARGS__)
+
+/*
+ * Maximum legal value for VOUT_SCALE_LOOP (0x29) on the MPQ8646 silicon
+ * The chip uses an 11-bit VOUT feedback-divider scale register.
+ */
+#define MPQ8646_VOUT_SCALE_LOOP_MAX GENMASK(10, 0)
+
+/* Forward declaration */
+struct mpq8646_dbg_reg_ctx;
+
+/* Per-instance state */
+struct mpq8646_priv {
+ struct pmbus_driver_info info; /* must be first, container_of target */
+ struct i2c_client *client;
+
+ atomic_t read_byte_calls;
+ atomic_t read_word_calls;
+ atomic_t write_byte_calls;
+ atomic_t read_byte_err;
+ atomic_t read_word_err;
+ atomic_t clear_faults_swallowed;
+ atomic_t page_writes_swallowed;
+
+ bool debug_force_raw_xfer;
+ unsigned int debug_delay_us;
+
+ int last_probe_rc;
+ u16 last_probe_data;
+
+ /* Serialises CLEAR_LAST_FAULT sequences and PROTECTION_LAST reads */
+ struct mutex mps_lock;
+
+ /*
+ * Adapted from lm90's alert_work pattern
+ * Set alarm_poll_interval_ms = 0 to disable.
+ */
+ struct delayed_work alarm_poll_work;
+ struct device *hwmon_dev;
+ u16 last_status_word;
+ u32 alarm_poll_interval_ms;
+
+#ifdef CONFIG_DEBUG_FS
+ struct dentry *debugfs_root;
+ struct mpq8646_dbg_reg_ctx *dbg_reg_ctx;
+#endif
+};
+
+struct mpq_status_bit {
+ u16 mask;
+ const char *name;
+};
+
+static const struct mpq_status_bit mpq8646_status_word_bits[] = {
+ { PB_STATUS_VOUT, "VOUT" },
+ { PB_STATUS_IOUT_POUT, "IOUT_POUT" },
+ { PB_STATUS_INPUT, "INPUT" },
+ { PB_STATUS_WORD_MFR, "NVM_SUMMARY" },
+ { PB_STATUS_POWER_GOOD_N, "POWER_GOOD#" },
+ { PB_STATUS_FANS, "FANS" },
+ { PB_STATUS_OTHER, "OTHER" },
+ { PB_STATUS_UNKNOWN, "WATCH_DOG" },
+ { PB_STATUS_BUSY, "BUSY" },
+ { PB_STATUS_OFF, "OFF" },
+ { PB_STATUS_VOUT_OV, "VOUT_OV_FAULT" },
+ { PB_STATUS_IOUT_OC, "IOUT_OC_FAULT" },
+ { PB_STATUS_VIN_UV, "VIN_UV_FAULT" },
+ { PB_STATUS_TEMPERATURE, "TEMP" },
+ { PB_STATUS_CML, "CML" },
+ { PB_STATUS_NONE_ABOVE, "DRMOS_FAULT" },
+ { /* sentinel */ }
+};
+
+/* PROTECTION_LAST (0xFB) bit names, it survives chip POR */
+static const struct mpq_status_bit mpq8646_protection_last_bits[] = {
+ { BIT(15), "INIT_FAULT" },
+ { BIT(14), "NVM_CRC_ERROR" },
+ { BIT(13), "NVM_FAULT" },
+ { BIT(12), "OC_PHASE_FAULT" },
+ { BIT(11), "OTP_SELF_FAULT" },
+ { BIT(9), "SWITCH_PRD_FAULT" },
+ { BIT(8), "VIN_OV_FAULT" },
+ { BIT(7), "VOUT_OV_FAULT" },
+ { BIT(6), "VOUT_UV_FAULT" },
+ { BIT(5), "OC_TOT_FAULT" },
+ { BIT(4), "VIN_UVLO_FAULT" },
+ { BIT(3), "DRMOS_OTP" },
+ { /* sentinel */ }
+};
+
+static inline struct mpq8646_priv *mpq8646_priv_from_client(struct i2c_client *client)
+{
+ const struct pmbus_driver_info *info = pmbus_get_driver_info(client);
+
+ return container_of(info, struct mpq8646_priv, info);
+}
+
+static int mpq8646_raw_xfer_rword(struct i2c_client *client, u8 reg)
+{
+ u8 cmd = reg;
+ __le16 data = 0;
+ struct i2c_msg msg[] = {
+ {
+ .addr = client->addr,
+ .flags = 0,
+ .len = sizeof(cmd),
+ .buf = &cmd,
+ },
+ {
+ .addr = client->addr,
+ .flags = I2C_M_RD,
+ .len = sizeof(data),
+ .buf = (u8 *)&data,
+ },
+ };
+ int rc;
+
+ rc = i2c_transfer(client->adapter, msg, ARRAY_SIZE(msg));
+ if (rc < 0)
+ return rc;
+ if (rc != ARRAY_SIZE(msg))
+ return -EIO;
+ return le16_to_cpu(data);
+}
+
+/*
+ * VID-mode m/b/R coefficients per MPS datasheet:
+ * y_uV = (m * raw + b * 10^-R) -- m=64 / R=1 gives 6.4 mV/LSB,
+ * which matches the chip's VID range.
+ */
+#define MPQ8646_VID_M 64
+#define MPQ8646_VID_B 0
+#define MPQ8646_VID_R 1
+
+static int mpq8646_identify(struct i2c_client *client,
+ struct pmbus_driver_info *info)
+{
+ int vout_mode;
+
+ vout_mode = pmbus_read_byte_data(client, 0, PMBUS_VOUT_MODE);
+ if (vout_mode < 0)
+ return vout_mode;
+ if (vout_mode == PB_VOUT_MODE_INVALID)
+ return -ENODEV;
+
+ switch ((vout_mode & PB_VOUT_MODE_MODE_MASK) >> PB_VOUT_MODE_MODE_SHIFT) {
+ case PB_VOUT_MODE_LINEAR >> PB_VOUT_MODE_MODE_SHIFT:
+ info->format[PSC_VOLTAGE_OUT] = linear;
+ break;
+ case PB_VOUT_MODE_VID >> PB_VOUT_MODE_MODE_SHIFT:
+ case PB_VOUT_MODE_DIRECT >> PB_VOUT_MODE_MODE_SHIFT:
+ info->format[PSC_VOLTAGE_OUT] = direct;
+ info->m[PSC_VOLTAGE_OUT] = MPQ8646_VID_M;
+ info->b[PSC_VOLTAGE_OUT] = MPQ8646_VID_B;
+ info->R[PSC_VOLTAGE_OUT] = MPQ8646_VID_R;
+ break;
+ default:
+ return -ENODEV;
+ }
+
+ return 0;
+};
+
+static int mpq8646_read_byte_data(struct i2c_client *client, int page, int reg)
+{
+ struct mpq8646_priv *priv = mpq8646_priv_from_client(client);
+ int ret;
+
+ atomic_inc(&priv->read_byte_calls);
+ MPQ8646_TRACE("read_byte_data page=%d reg=0x%02x\n", page, reg);
+
+ if (priv->debug_delay_us)
+ udelay(priv->debug_delay_us);
+
+ switch (reg) {
+ case PMBUS_VOUT_MODE:
+ ret = pmbus_read_byte_data(client, page, reg);
+ MPQ8646_TRACE(" VOUT_MODE raw=0x%02x ret=%d\n", ret, ret);
+ if (ret < 0) {
+ atomic_inc(&priv->read_byte_err);
+ return ret;
+ }
+
+ if ((ret >> 5) == 1)
+ return PB_VOUT_MODE_DIRECT;
+
+ return ret;
+ case PMBUS_WRITE_PROTECT:
+ MPQ8646_TRACE(" WRITE_PROTECT shimmed to 0 (framework path)\n");
+ return 0;
+ case PMBUS_STATUS_BYTE:
+ case PMBUS_STATUS_CML:
+ case PMBUS_STATUS_OTHER:
+ case PMBUS_STATUS_MFR_SPECIFIC:
+ case PMBUS_STATUS_FAN_12:
+ case PMBUS_STATUS_FAN_34:
+ return -ENXIO;
+ case PMBUS_MFR_LOCATION:
+ case PMBUS_MFR_DATE:
+ case PMBUS_MFR_SERIAL:
+ case PMBUS_IC_DEVICE_ID:
+ case PMBUS_IC_DEVICE_REV:
+ MPQ8646_TRACE(" unsupported mfr-info reg 0x%02x -> ENXIO\n", reg);
+ return -ENXIO;
+ default:
+ return -ENODATA;
+ }
+}
+
+static int mpq8646_write_byte(struct i2c_client *client, int page, u8 value)
+{
+ struct mpq8646_priv *priv = mpq8646_priv_from_client(client);
+
+ atomic_inc(&priv->write_byte_calls);
+ MPQ8646_TRACE("write_byte page=%d value=0x%02x\n", page, value);
+
+ if (priv->debug_delay_us)
+ udelay(priv->debug_delay_us);
+
+ if (value == PMBUS_PAGE) {
+ atomic_inc(&priv->page_writes_swallowed);
+ return 0;
+ }
+
+ return -ENODATA; /* let core do the standard direct write */
+}
+
+/*
+ * Reference: ltc2978.c::ltc2978_write_word_data which uses the
+ * same virtual-register channel for its real chip-side peak reset.
+ */
+static int mpq8646_write_word_data(struct i2c_client *client, int page,
+ int reg, u16 word)
+{
+ struct mpq8646_priv *priv = mpq8646_priv_from_client(client);
+ int rc;
+
+ switch (reg) {
+ case PMBUS_VIRT_RESET_VIN_HISTORY:
+ case PMBUS_VIRT_RESET_VOUT_HISTORY:
+ case PMBUS_VIRT_RESET_IOUT_HISTORY:
+ case PMBUS_VIRT_RESET_TEMP_HISTORY:
+ MPQ8646_TRACE("reset_history virt reg=0x%04x -> CLEAR_FAULTS\n",
+ reg);
+ rc = i2c_smbus_write_byte(priv->client, PMBUS_CLEAR_FAULTS);
+ if (rc < 0)
+ MPQ8646_TRACE(" CLEAR_FAULTS rc=%d\n", rc);
+ return rc < 0 ? rc : 0;
+ default:
+ return -ENODATA; /* let pmbus_core do the direct write */
+ }
+}
+
+static int mpq8646_read_word_data(struct i2c_client *client, int page,
+ int phase, int reg)
+{
+ struct mpq8646_priv *priv = mpq8646_priv_from_client(client);
+ int rc;
+
+ atomic_inc(&priv->read_word_calls);
+ MPQ8646_TRACE("read_word_data page=%d phase=%d reg=0x%02x%s\n",
+ page, phase, reg,
+ priv->debug_force_raw_xfer ? " [force-raw]" : "");
+
+ if (priv->debug_delay_us)
+ udelay(priv->debug_delay_us);
+
+ switch (reg) {
+ case PMBUS_READ_VIN:
+ case PMBUS_READ_VOUT:
+ case PMBUS_READ_IOUT:
+ case PMBUS_READ_TEMPERATURE_1:
+ case PMBUS_STATUS_WORD:
+ case PMBUS_VOUT_OV_FAULT_LIMIT:
+ case PMBUS_VOUT_OV_WARN_LIMIT:
+ case PMBUS_VOUT_UV_WARN_LIMIT:
+ case PMBUS_VOUT_UV_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_FAULT_LIMIT:
+ case PMBUS_IOUT_OC_WARN_LIMIT:
+ case PMBUS_OT_FAULT_LIMIT:
+ case PMBUS_OT_WARN_LIMIT:
+ case PMBUS_VIN_OV_FAULT_LIMIT:
+ case PMBUS_VIN_OV_WARN_LIMIT:
+ case PMBUS_VIN_UV_WARN_LIMIT:
+ case PMBUS_VIN_UV_FAULT_LIMIT:
+ case PMBUS_MFR_VIN_MAX:
+ case PMBUS_MFR_VOUT_MAX:
+ case PMBUS_MFR_IOUT_MAX:
+ case PMBUS_MFR_MAX_TEMP_1:
+ break;
+ case PMBUS_VIRT_RESET_VIN_HISTORY:
+ case PMBUS_VIRT_RESET_VOUT_HISTORY:
+ case PMBUS_VIRT_RESET_IOUT_HISTORY:
+ case PMBUS_VIRT_RESET_TEMP_HISTORY:
+ return 0;
+ default:
+ return -ENODATA;
+ }
+
+ if (priv->debug_force_raw_xfer)
+ rc = mpq8646_raw_xfer_rword(client, reg);
+ else
+ rc = i2c_smbus_read_word_data(client, reg);
+
+ if (rc < 0)
+ atomic_inc(&priv->read_word_err);
+
+ MPQ8646_TRACE(" reg=0x%02x rc=%d\n", reg, rc);
+ return rc;
+}
+
+static struct pmbus_driver_info mpq8646_info = {
+ .pages = 1,
+ .format[PSC_VOLTAGE_IN] = direct,
+ .format[PSC_CURRENT_OUT] = direct,
+ .format[PSC_TEMPERATURE] = direct,
+ .m[PSC_VOLTAGE_IN] = 4,
+ .b[PSC_VOLTAGE_IN] = 0,
+ .R[PSC_VOLTAGE_IN] = 1,
+ .m[PSC_CURRENT_OUT] = 16,
+ .b[PSC_CURRENT_OUT] = 0,
+ .R[PSC_CURRENT_OUT] = 0,
+ .m[PSC_TEMPERATURE] = 1,
+ .b[PSC_TEMPERATURE] = 0,
+ .R[PSC_TEMPERATURE] = 0,
+ .func[0] = PMBUS_HAVE_VIN | PMBUS_HAVE_VOUT |
+ PMBUS_HAVE_IOUT | PMBUS_HAVE_TEMP |
+ PMBUS_HAVE_STATUS_INPUT | PMBUS_HAVE_STATUS_VOUT |
+ PMBUS_HAVE_STATUS_IOUT | PMBUS_HAVE_STATUS_TEMP,
+};
+
+#if IS_ENABLED(CONFIG_REGULATOR)
+static const struct regulator_desc mpq8646_reg_desc[] = {
+ PMBUS_REGULATOR("vout", 0),
+};
+#endif /* CONFIG_REGULATOR */
+
+#if IS_ENABLED(CONFIG_NVMEM)
+/*
+ * Expose using
+ * /sys/bus/nvmem/devices/<i2c-name>/nvmem
+ *
+ * Layout (16 bytes):
+ * offset 0..1 PROTECTION_LAST (0xFB) word, LE -- NVM
+ * offset 2..3 MFR_RETRY_TIMES (0xF4) word, LE -- NVM
+ * offset 4..5 MFR_CONFIG_ID (0xC0) word, LE -- NVM
+ * offset 6..7 MFR_VBOOT_CFG (0xFC) word, LE -- NVM
+ * offset 8 MFR_SILICON_REV (0xC3) byte -- NVM
+ * offset 9..15 reserved (zero-fill, leaves room for additions)
+ */
+#define MPQ8646_NVMEM_SIZE 16
+
+struct mpq8646_nvmem_entry {
+ unsigned int off;
+ u8 reg;
+ bool is_word;
+};
+
+static const struct mpq8646_nvmem_entry mpq8646_nvmem_map[] = {
+ { 0, MPS_PROTECTION_LAST, true },
+ { 2, MPS_MFR_RETRY_TIMES, true },
+ { 4, MPS_MFR_CONFIG_ID, true },
+ { 6, MPS_MFR_VBOOT_CFG, true },
+ { 8, MPS_MFR_SILICON_REV, false },
+};
+
+static int mpq8646_nvmem_read(void *data, unsigned int offset, void *val,
+ size_t bytes)
+{
+ struct mpq8646_priv *priv = data;
+ u8 *out = val;
+ size_t i;
+
+ if (offset >= MPQ8646_NVMEM_SIZE)
+ return -EINVAL;
+ if (offset + bytes > MPQ8646_NVMEM_SIZE)
+ bytes = MPQ8646_NVMEM_SIZE - offset;
+
+ memset(out, 0, bytes);
+
+ for (i = 0; i < ARRAY_SIZE(mpq8646_nvmem_map); i++) {
+ const struct mpq8646_nvmem_entry *e = &mpq8646_nvmem_map[i];
+ unsigned int e_start = e->off;
+ unsigned int e_end = e_start + (e->is_word ? 2 : 1);
+ u8 raw[2];
+ int rc;
+ unsigned int j;
+
+ if (e_end <= offset || e_start >= offset + bytes)
+ continue; /* outside requested slice */
+
+ if (e->is_word)
+ rc = i2c_smbus_read_word_data(priv->client, e->reg);
+ else
+ rc = i2c_smbus_read_byte_data(priv->client, e->reg);
+ if (rc < 0)
+ continue; /* leave the zero-fill in place */
+
+ raw[0] = rc & 0xff;
+ raw[1] = (rc >> 8) & 0xff;
+
+ for (j = 0; j < e_end - e_start; j++) {
+ unsigned int abs = e_start + j;
+
+ if (abs >= offset && abs < offset + bytes)
+ out[abs - offset] = raw[j];
+ }
+ }
+ return 0;
+}
+#endif /* CONFIG_NVMEM */
+
+static const struct i2c_device_id mpq8646_id[] = {
+ { "mpq8646", 0 },
+ { },
+};
+MODULE_DEVICE_TABLE(i2c, mpq8646_id);
+
+static const struct of_device_id __maybe_unused mpq8646_of_match[] = {
+ { .compatible = "mps,mpq8646" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, mpq8646_of_match);
+
+static struct pmbus_platform_data mpq8646_no_pec_pdata = {
+ .flags = PMBUS_NO_CAPABILITY,
+};
+
+#ifdef CONFIG_DEBUG_FS
+/*
+ * /sys/kernel/debug/mpq8646/<bus>-<addr>/
+ * probe_smbus_rword echo <reg> call i2c_smbus_read_word_data
+ * probe_smbus_rbyte echo <reg> call i2c_smbus_read_byte_data
+ * probe_raw_xfer echo <reg> call i2c_transfer manually
+ * probe_page_write echo <pg> write PMBUS_PAGE = pg
+ * probe_clear_faults echo 1 send CLEAR_FAULTS Send-Byte
+ * force_raw_xfer 0|1 production read_word_data path
+ * delay_us <N> udelay before each hook
+ * last_probe read-only "rc=<rc> data=0x<hex>"
+ * stats read-only counters
+ * reset_stats write-only zero counters
+ */
+
+static int mpq8646_dbg_probe_smbus_rword(void *data, u64 val)
+{
+ struct mpq8646_priv *priv = data;
+ int rc;
+
+ rc = i2c_smbus_read_word_data(priv->client, (u8)val);
+ priv->last_probe_rc = rc;
+ priv->last_probe_data = (rc < 0) ? 0 : (u16)rc;
+ return 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(mpq8646_dbg_probe_smbus_rword_fops,
+ NULL, mpq8646_dbg_probe_smbus_rword, "%llu\n");
+
+static int mpq8646_dbg_probe_smbus_rbyte(void *data, u64 val)
+{
+ struct mpq8646_priv *priv = data;
+ int rc;
+
+ rc = i2c_smbus_read_byte_data(priv->client, (u8)val);
+ priv->last_probe_rc = rc;
+ priv->last_probe_data = (rc < 0) ? 0 : (u8)rc;
+ return 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(mpq8646_dbg_probe_smbus_rbyte_fops,
+ NULL, mpq8646_dbg_probe_smbus_rbyte, "%llu\n");
+
+static int mpq8646_dbg_probe_raw_xfer(void *data, u64 val)
+{
+ struct mpq8646_priv *priv = data;
+ int rc;
+
+ rc = mpq8646_raw_xfer_rword(priv->client, (u8)val);
+ priv->last_probe_rc = rc;
+ priv->last_probe_data = (rc < 0) ? 0 : (u16)rc;
+ return 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(mpq8646_dbg_probe_raw_xfer_fops,
+ NULL, mpq8646_dbg_probe_raw_xfer, "%llu\n");
+
+static int mpq8646_dbg_probe_page_write(void *data, u64 val)
+{
+ struct mpq8646_priv *priv = data;
+ int rc;
+
+ rc = i2c_smbus_write_byte_data(priv->client, PMBUS_PAGE, (u8)val);
+ priv->last_probe_rc = rc;
+ priv->last_probe_data = 0;
+ return 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(mpq8646_dbg_probe_page_write_fops,
+ NULL, mpq8646_dbg_probe_page_write, "%llu\n");
+
+static int mpq8646_dbg_probe_clear_faults(void *data, u64 val)
+{
+ struct mpq8646_priv *priv = data;
+ int rc;
+
+ if (!val)
+ return 0;
+ rc = i2c_smbus_write_byte(priv->client, PMBUS_CLEAR_FAULTS);
+ priv->last_probe_rc = rc;
+ priv->last_probe_data = 0;
+ return 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(mpq8646_dbg_probe_clear_faults_fops,
+ NULL, mpq8646_dbg_probe_clear_faults, "%llu\n");
+
+static int mpq8646_dbg_last_probe_show(struct seq_file *s, void *unused)
+{
+ struct mpq8646_priv *priv = s->private;
+
+ seq_printf(s, "rc=%d data=0x%04x\n",
+ priv->last_probe_rc, priv->last_probe_data);
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(mpq8646_dbg_last_probe);
+
+static int mpq8646_dbg_stats_show(struct seq_file *s, void *unused)
+{
+ struct mpq8646_priv *priv = s->private;
+
+ seq_printf(s,
+ "read_byte_calls : %d\n"
+ "read_word_calls : %d\n"
+ "write_byte_calls : %d\n"
+ "read_byte_err : %d\n"
+ "read_word_err : %d\n"
+ "clear_faults_swallowed : %d\n"
+ "page_writes_swallowed : %d\n"
+ "force_raw_xfer : %d\n"
+ "delay_us : %u\n",
+ atomic_read(&priv->read_byte_calls),
+ atomic_read(&priv->read_word_calls),
+ atomic_read(&priv->write_byte_calls),
+ atomic_read(&priv->read_byte_err),
+ atomic_read(&priv->read_word_err),
+ atomic_read(&priv->clear_faults_swallowed),
+ atomic_read(&priv->page_writes_swallowed),
+ priv->debug_force_raw_xfer,
+ priv->debug_delay_us);
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(mpq8646_dbg_stats);
+
+static int mpq8646_dbg_reset_stats(void *data, u64 val)
+{
+ struct mpq8646_priv *priv = data;
+
+ if (!val)
+ return 0;
+ atomic_set(&priv->read_byte_calls, 0);
+ atomic_set(&priv->read_word_calls, 0);
+ atomic_set(&priv->write_byte_calls, 0);
+ atomic_set(&priv->read_byte_err, 0);
+ atomic_set(&priv->read_word_err, 0);
+ atomic_set(&priv->clear_faults_swallowed, 0);
+ atomic_set(&priv->page_writes_swallowed, 0);
+ return 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(mpq8646_dbg_reset_stats_fops,
+ NULL, mpq8646_dbg_reset_stats, "%llu\n");
+
+static void mpq8646_print_bits(struct seq_file *s, u16 v,
+ const struct mpq_status_bit *tab)
+{
+ const struct mpq_status_bit *t;
+ bool first = true;
+
+ seq_printf(s, "0x%04x", v);
+ if (!v) {
+ seq_puts(s, " [clean]\n");
+ return;
+ }
+ seq_puts(s, " [");
+ for (t = tab; t->mask; t++) {
+ if (v & t->mask) {
+ if (!first)
+ seq_putc(s, ' ');
+ seq_puts(s, t->name);
+ first = false;
+ }
+ }
+ seq_puts(s, "]\n");
+}
+
+static int mpq8646_dbg_status_decoded_show(struct seq_file *s, void *unused)
+{
+ struct mpq8646_priv *priv = s->private;
+ int rc;
+
+ rc = i2c_smbus_read_word_data(priv->client, PMBUS_STATUS_WORD);
+ if (rc < 0) {
+ seq_printf(s, "ERROR: STATUS_WORD read failed (%d)\n", rc);
+ return 0;
+ }
+ seq_puts(s, "STATUS_WORD: ");
+ mpq8646_print_bits(s, (u16)rc, mpq8646_status_word_bits);
+ seq_puts(s, "(MPS extensions: bit12=NVM_SUMMARY, bit8=WATCH_DOG, bit0=DRMOS_FAULT)\n");
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(mpq8646_dbg_status_decoded);
+
+static int mpq8646_dbg_protection_last_show(struct seq_file *s, void *unused)
+{
+ struct mpq8646_priv *priv = s->private;
+ int rc;
+
+ mutex_lock(&priv->mps_lock);
+ rc = i2c_smbus_read_word_data(priv->client, MPS_PROTECTION_LAST);
+ mutex_unlock(&priv->mps_lock);
+
+ if (rc < 0) {
+ seq_printf(s, "ERROR: PROTECTION_LAST read failed (%d)\n", rc);
+ return 0;
+ }
+ seq_puts(s, "PROTECTION_LAST: ");
+ mpq8646_print_bits(s, (u16)rc, mpq8646_protection_last_bits);
+ seq_puts(s, "(NVM-backed, survives chip POR; clear via clear_protection_last[_force])\n");
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(mpq8646_dbg_protection_last);
+
+struct mpq8646_dbg_reg {
+ u8 reg;
+ bool is_word;
+ bool writable;
+ const char *name;
+};
+
+static const struct mpq8646_dbg_reg mpq8646_dbg_regs[] = {
+ /* MPS vendor extensions (read-only identity / observability) */
+ { MPS_MFR_CONFIG_ID, true, false, "mfr_config_id" },
+ { MPS_MFR_CONFIG_CODE_REV, true, false, "mfr_config_code_rev" },
+ { MPS_MFR_SILICON_REV, false, false, "mfr_silicon_rev" },
+ { MPS_MFR_RETRY_TIMES, true, false, "mfr_retry_times" },
+ { MPS_MFR_VBOOT_CFG, true, false, "mfr_vboot_cfg" },
+ /* MPS vendor extension -- user-writable product revision string */
+ { MPS_MFR_PRODUCT_REV_USER, true, true, "mfr_product_rev_user" },
+ /* PMBus 1.3 standard timing / UVLO (read-only introspection) */
+ { PMBUS_VIN_ON, true, false, "vin_on" },
+ { PMBUS_VIN_OFF, true, false, "vin_off" },
+ { PMBUS_TON_DELAY, true, false, "ton_delay" },
+ { PMBUS_TON_RISE, true, false, "ton_rise" },
+ { PMBUS_TOFF_DELAY, true, false, "toff_delay" },
+ { PMBUS_TOFF_FALL, true, false, "toff_fall" },
+ /* PMBus 1.3 control / margin (read+write) */
+ { PMBUS_ON_OFF_CONFIG, false, true, "on_off_config" },
+ { PMBUS_VOUT_MARGIN_HIGH, true, true, "vout_margin_high" },
+ { PMBUS_VOUT_MARGIN_LOW, true, true, "vout_margin_low" },
+ /* MPS PMBus-level write-protect (read+write) */
+ { MPS_MFR_PMBUS_LOCK, true, true, "mfr_pmbus_lock" },
+};
+
+struct mpq8646_dbg_reg_ctx {
+ struct mpq8646_priv *priv;
+ const struct mpq8646_dbg_reg *desc;
+};
+
+static int mpq8646_dbg_reg_show(struct seq_file *s, void *unused)
+{
+ struct mpq8646_dbg_reg_ctx *ctx = s->private;
+ int rc;
+
+ if (ctx->desc->is_word)
+ rc = i2c_smbus_read_word_data(ctx->priv->client,
+ ctx->desc->reg);
+ else
+ rc = i2c_smbus_read_byte_data(ctx->priv->client,
+ ctx->desc->reg);
+
+ if (rc < 0) {
+ seq_printf(s, "ERROR: reg 0x%02x (%s) read failed (%d)\n",
+ ctx->desc->reg, ctx->desc->name, rc);
+ return 0;
+ }
+ seq_printf(s, "0x%0*x\n", ctx->desc->is_word ? 4 : 2, rc);
+ return 0;
+}
+DEFINE_SHOW_ATTRIBUTE(mpq8646_dbg_reg);
+
+static int mpq8646_dbg_reg_get(void *data, u64 *val)
+{
+ struct mpq8646_dbg_reg_ctx *ctx = data;
+ int rc;
+
+ if (ctx->desc->is_word)
+ rc = i2c_smbus_read_word_data(ctx->priv->client,
+ ctx->desc->reg);
+ else
+ rc = i2c_smbus_read_byte_data(ctx->priv->client,
+ ctx->desc->reg);
+ if (rc < 0)
+ return rc;
+ *val = rc;
+ return 0;
+}
+
+static int mpq8646_dbg_reg_set(void *data, u64 val)
+{
+ struct mpq8646_dbg_reg_ctx *ctx = data;
+ int rc;
+
+ if (ctx->desc->is_word)
+ rc = i2c_smbus_write_word_data(ctx->priv->client,
+ ctx->desc->reg, (u16)val);
+ else
+ rc = i2c_smbus_write_byte_data(ctx->priv->client,
+ ctx->desc->reg, (u8)val);
+ return rc < 0 ? rc : 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(mpq8646_dbg_reg_rw_fops,
+ mpq8646_dbg_reg_get, mpq8646_dbg_reg_set, "0x%llx\n");
+
+static int mpq8646_dbg_clear_protection_last(void *data, u64 val)
+{
+ struct mpq8646_priv *priv = data;
+ int rc;
+
+ if (!val)
+ return 0;
+
+ mutex_lock(&priv->mps_lock);
+ rc = i2c_smbus_write_byte(priv->client, MPS_CLEAR_LAST_FAULT);
+ mutex_unlock(&priv->mps_lock);
+
+ priv->last_probe_rc = rc;
+ priv->last_probe_data = 0;
+ return 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(mpq8646_dbg_clear_protection_last_fops,
+ NULL, mpq8646_dbg_clear_protection_last, "%llu\n");
+
+static int mpq8646_dbg_clear_protection_last_force(void *data, u64 val)
+{
+ struct mpq8646_priv *priv = data;
+ int rc, last_rc;
+ int wp_orig, cfg_orig;
+
+ if (!val)
+ return 0;
+
+ mutex_lock(&priv->mps_lock);
+
+ wp_orig = i2c_smbus_read_byte_data(priv->client, PMBUS_WRITE_PROTECT);
+ if (wp_orig < 0) {
+ priv->last_probe_rc = wp_orig;
+ dev_warn(&priv->client->dev,
+ "clear_protection_last_force: WRITE_PROTECT read failed (%d), aborting\n",
+ wp_orig);
+ goto out;
+ }
+ cfg_orig = i2c_smbus_read_word_data(priv->client, MPS_MFR_CFG_EXT);
+ if (cfg_orig < 0) {
+ priv->last_probe_rc = cfg_orig;
+ dev_warn(&priv->client->dev,
+ "clear_protection_last_force: MFR_CFG_EXT read failed (%d), aborting\n",
+ cfg_orig);
+ goto out;
+ }
+
+ if (wp_orig != 0) {
+ rc = i2c_smbus_write_byte_data(priv->client,
+ PMBUS_WRITE_PROTECT, 0);
+ if (rc < 0) {
+ priv->last_probe_rc = rc;
+ dev_warn(&priv->client->dev,
+ "clear_protection_last_force: WP clear failed (%d), aborting\n",
+ rc);
+ goto out;
+ }
+ }
+
+ rc = i2c_smbus_write_word_data(priv->client, MPS_MFR_CFG_EXT,
+ (u16)cfg_orig | MPS_MFR_CFG_EXT_CLR_LAST_EN);
+ if (rc < 0) {
+ priv->last_probe_rc = rc;
+ dev_warn(&priv->client->dev,
+ "clear_protection_last_force: gate open failed (%d)\n",
+ rc);
+ goto restore_wp;
+ }
+
+ last_rc = i2c_smbus_write_byte(priv->client, MPS_CLEAR_LAST_FAULT);
+ priv->last_probe_rc = last_rc;
+ if (last_rc < 0)
+ dev_warn(&priv->client->dev,
+ "clear_protection_last_force: CLEAR_LAST_FAULT failed (%d) even with gate open\n",
+ last_rc);
+
+ for (int attempt = 0; attempt < MPQ8646_NVM_RETRY_MAX; attempt++) {
+ rc = i2c_smbus_write_word_data(priv->client, MPS_MFR_CFG_EXT,
+ (u16)cfg_orig);
+ if (rc >= 0)
+ break;
+ usleep_range(MPQ8646_NVM_RETRY_DELAY_US_MIN,
+ MPQ8646_NVM_RETRY_DELAY_US_MAX);
+ }
+ if (rc < 0)
+ dev_warn(&priv->client->dev,
+ "clear_protection_last_force: MFR_CFG_EXT restore failed after retries (%d) -- gate may stay open until POR\n",
+ rc);
+
+restore_wp:
+ if (wp_orig != 0) {
+ rc = i2c_smbus_write_byte_data(priv->client,
+ PMBUS_WRITE_PROTECT,
+ (u8)wp_orig);
+ if (rc < 0)
+ dev_warn(&priv->client->dev,
+ "clear_protection_last_force: WP restore failed (%d)\n",
+ rc);
+ }
+out:
+ mutex_unlock(&priv->mps_lock);
+ return 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(mpq8646_dbg_clear_protection_last_force_fops,
+ NULL, mpq8646_dbg_clear_protection_last_force, "%llu\n");
+
+static int mpq8646_dbg_store_all(void *data, u64 val)
+{
+ struct mpq8646_priv *priv = data;
+ int rc;
+
+ if (!val)
+ return 0;
+
+ mutex_lock(&priv->mps_lock);
+ rc = i2c_smbus_write_byte(priv->client, PMBUS_STORE_USER_ALL);
+ mutex_unlock(&priv->mps_lock);
+
+ priv->last_probe_rc = rc;
+ priv->last_probe_data = 0;
+ if (rc < 0)
+ dev_warn(&priv->client->dev,
+ "store_all: STORE_DEFAULT_ALL (0x11/0x15) write failed (%d)\n",
+ rc);
+ return 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(mpq8646_dbg_store_all_fops,
+ NULL, mpq8646_dbg_store_all, "%llu\n");
+
+static int mpq8646_dbg_restore_all(void *data, u64 val)
+{
+ struct mpq8646_priv *priv = data;
+ int rc;
+
+ if (!val)
+ return 0;
+
+ mutex_lock(&priv->mps_lock);
+ rc = i2c_smbus_write_byte(priv->client, PMBUS_RESTORE_USER_ALL);
+ mutex_unlock(&priv->mps_lock);
+
+ priv->last_probe_rc = rc;
+ priv->last_probe_data = 0;
+ if (rc < 0)
+ dev_warn(&priv->client->dev,
+ "restore_all: RESTORE_DEFAULT_ALL (0x12/0x16) write failed (%d)\n",
+ rc);
+ return 0;
+}
+DEFINE_DEBUGFS_ATTRIBUTE(mpq8646_dbg_restore_all_fops,
+ NULL, mpq8646_dbg_restore_all, "%llu\n");
+
+#define MPQ8646_DEBUGFS_DIRNAME_MAX 16
+
+#define MPQ8646_DEBUGFS_ROOT_NAME "mpq8646"
+
+static void mpq8646_debugfs_register(struct mpq8646_priv *priv)
+{
+ struct dentry *root, *parent;
+ char name[MPQ8646_DEBUGFS_DIRNAME_MAX];
+ size_t i;
+
+ parent = debugfs_lookup(MPQ8646_DEBUGFS_ROOT_NAME, NULL);
+ if (!parent)
+ parent = debugfs_create_dir(MPQ8646_DEBUGFS_ROOT_NAME, NULL);
+ if (IS_ERR_OR_NULL(parent))
+ return;
+
+ snprintf(name, sizeof(name), "%d-%04x",
+ i2c_adapter_id(priv->client->adapter), priv->client->addr);
+ root = debugfs_create_dir(name, parent);
+ if (IS_ERR_OR_NULL(root))
+ return;
+
+ priv->debugfs_root = root;
+
+ debugfs_create_file_unsafe("probe_smbus_rword", 0200, root, priv,
+ &mpq8646_dbg_probe_smbus_rword_fops);
+ debugfs_create_file_unsafe("probe_smbus_rbyte", 0200, root, priv,
+ &mpq8646_dbg_probe_smbus_rbyte_fops);
+ debugfs_create_file_unsafe("probe_raw_xfer", 0200, root, priv,
+ &mpq8646_dbg_probe_raw_xfer_fops);
+ debugfs_create_file_unsafe("probe_page_write", 0200, root, priv,
+ &mpq8646_dbg_probe_page_write_fops);
+ debugfs_create_file_unsafe("probe_clear_faults", 0200, root, priv,
+ &mpq8646_dbg_probe_clear_faults_fops);
+ debugfs_create_bool("force_raw_xfer", 0600, root,
+ &priv->debug_force_raw_xfer);
+ debugfs_create_u32("delay_us", 0600, root, &priv->debug_delay_us);
+ debugfs_create_file("last_probe", 0400, root, priv,
+ &mpq8646_dbg_last_probe_fops);
+ debugfs_create_file("stats", 0400, root, priv,
+ &mpq8646_dbg_stats_fops);
+ debugfs_create_file_unsafe("reset_stats", 0200, root, priv,
+ &mpq8646_dbg_reset_stats_fops);
+ /* MPS extensions: status decode + NVM-backed PROTECTION_LAST */
+ debugfs_create_file("status_decoded", 0400, root, priv,
+ &mpq8646_dbg_status_decoded_fops);
+ debugfs_create_file("protection_last", 0400, root, priv,
+ &mpq8646_dbg_protection_last_fops);
+ debugfs_create_file_unsafe("clear_protection_last", 0200, root, priv,
+ &mpq8646_dbg_clear_protection_last_fops);
+ debugfs_create_file_unsafe("clear_protection_last_force", 0200, root, priv,
+ &mpq8646_dbg_clear_protection_last_force_fops);
+ debugfs_create_file_unsafe("store_all", 0200, root, priv,
+ &mpq8646_dbg_store_all_fops);
+ debugfs_create_file_unsafe("restore_all", 0200, root, priv,
+ &mpq8646_dbg_restore_all_fops);
+ debugfs_create_u32("alarm_poll_interval_ms", 0600, root,
+ &priv->alarm_poll_interval_ms);
+
+ priv->dbg_reg_ctx = devm_kcalloc(&priv->client->dev,
+ ARRAY_SIZE(mpq8646_dbg_regs),
+ sizeof(*priv->dbg_reg_ctx),
+ GFP_KERNEL);
+ if (!priv->dbg_reg_ctx)
+ return;
+ for (i = 0; i < ARRAY_SIZE(mpq8646_dbg_regs); i++) {
+ priv->dbg_reg_ctx[i].priv = priv;
+ priv->dbg_reg_ctx[i].desc = &mpq8646_dbg_regs[i];
+ if (mpq8646_dbg_regs[i].writable)
+ debugfs_create_file_unsafe(mpq8646_dbg_regs[i].name,
+ 0600, root,
+ &priv->dbg_reg_ctx[i],
+ &mpq8646_dbg_reg_rw_fops);
+ else
+ debugfs_create_file(mpq8646_dbg_regs[i].name, 0400,
+ root, &priv->dbg_reg_ctx[i],
+ &mpq8646_dbg_reg_fops);
+ }
+}
+
+static void mpq8646_debugfs_unregister(struct mpq8646_priv *priv)
+{
+ debugfs_remove_recursive(priv->debugfs_root);
+}
+#else
+static inline void mpq8646_debugfs_register(struct mpq8646_priv *priv) {}
+static inline void mpq8646_debugfs_unregister(struct mpq8646_priv *priv) {}
+#endif /* CONFIG_DEBUG_FS */
+
+static const struct {
+ u16 mask;
+ enum hwmon_sensor_types type;
+ u32 attr;
+ int channel;
+} mpq8646_alarm_map[] = {
+ { PB_STATUS_INPUT, hwmon_in, hwmon_in_alarm, 0 }, /* in1_alarm (VIN) */
+ { PB_STATUS_VOUT, hwmon_in, hwmon_in_alarm, 1 }, /* in2_alarm (VOUT) */
+ { PB_STATUS_IOUT_POUT, hwmon_curr, hwmon_curr_alarm, 0 }, /* curr1_alarm */
+ { PB_STATUS_TEMPERATURE, hwmon_temp, hwmon_temp_alarm, 0 }, /* temp1_alarm */
+};
+
+/* Adapted from lm90.c */
+static void mpq8646_alarm_poll_work(struct work_struct *work)
+{
+ struct mpq8646_priv *priv = container_of(to_delayed_work(work),
+ struct mpq8646_priv,
+ alarm_poll_work);
+ int rc;
+ u16 cur, newly_set;
+ size_t i;
+
+ if (priv->client->irq)
+ goto rearm;
+
+ if (!priv->alarm_poll_interval_ms)
+ return; /* polling disabled; don't re-arm */
+
+ if (!priv->hwmon_dev)
+ goto rearm; /* hwmon not ready yet; try again next tick */
+
+ rc = i2c_smbus_read_word_data(priv->client, PMBUS_STATUS_WORD);
+ if (rc < 0)
+ goto rearm;
+
+ cur = (u16)rc;
+ newly_set = cur & ~priv->last_status_word;
+ priv->last_status_word = cur;
+
+ if (!newly_set)
+ goto rearm;
+
+ for (i = 0; i < ARRAY_SIZE(mpq8646_alarm_map); i++) {
+ if (newly_set & mpq8646_alarm_map[i].mask)
+ hwmon_notify_event(priv->hwmon_dev,
+ mpq8646_alarm_map[i].type,
+ mpq8646_alarm_map[i].attr,
+ mpq8646_alarm_map[i].channel);
+ }
+
+rearm:
+ if (priv->alarm_poll_interval_ms)
+ schedule_delayed_work(&priv->alarm_poll_work,
+ msecs_to_jiffies(priv->alarm_poll_interval_ms));
+}
+
+static int mpq8646_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct pmbus_driver_info *info;
+ struct mpq8646_priv *priv;
+ u32 voltage_scale;
+ int ret;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+ priv->client = client;
+ mutex_init(&priv->mps_lock);
+ memcpy(&priv->info, &mpq8646_info, sizeof(priv->info));
+ info = &priv->info;
+
+ info->identify = mpq8646_identify;
+ info->read_byte_data = mpq8646_read_byte_data;
+ info->read_word_data = mpq8646_read_word_data;
+ info->write_byte = mpq8646_write_byte;
+ info->write_word_data = mpq8646_write_word_data;
+ dev->platform_data = &mpq8646_no_pec_pdata;
+
+#if IS_ENABLED(CONFIG_REGULATOR)
+ info->reg_desc = mpq8646_reg_desc;
+ info->num_regulators = ARRAY_SIZE(mpq8646_reg_desc);
+#endif
+
+ INIT_DELAYED_WORK(&priv->alarm_poll_work, mpq8646_alarm_poll_work);
+ priv->alarm_poll_interval_ms = MPQ8646_ALARM_POLL_MS_DEFAULT;
+
+ mpq8646_debugfs_register(priv);
+
+ if (!device_property_read_u32(dev, "mps,vout-fb-divider-ratio-permille",
+ &voltage_scale)) {
+ if (voltage_scale > MPQ8646_VOUT_SCALE_LOOP_MAX)
+ return -EINVAL;
+
+ ret = i2c_smbus_write_word_data(client, PMBUS_VOUT_SCALE_LOOP,
+ voltage_scale);
+ if (ret)
+ return ret;
+ }
+
+ ret = pmbus_do_probe(client, info);
+ if (ret) {
+ mpq8646_debugfs_unregister(priv);
+ return ret;
+ }
+
+ priv->hwmon_dev = pmbus_get_hwmon_device(client);
+ schedule_delayed_work(&priv->alarm_poll_work,
+ msecs_to_jiffies(priv->alarm_poll_interval_ms));
+
+#if IS_ENABLED(CONFIG_NVMEM)
+ {
+ struct nvmem_config cfg = {
+ .dev = &client->dev,
+ .name = dev_name(&client->dev),
+ .owner = THIS_MODULE,
+ .read_only = true,
+ .root_only = true,
+ .word_size = 1,
+ .stride = 1,
+ .size = MPQ8646_NVMEM_SIZE,
+ .reg_read = mpq8646_nvmem_read,
+ .priv = priv,
+ };
+ struct nvmem_device *nv = devm_nvmem_register(&client->dev, &cfg);
+
+ if (IS_ERR(nv))
+ dev_warn(&client->dev,
+ "nvmem snapshot register failed (%pe)\n",
+ nv);
+ }
+#endif
+ return 0;
+};
+
+static void mpq8646_remove(struct i2c_client *client)
+{
+ struct mpq8646_priv *priv = mpq8646_priv_from_client(client);
+
+ cancel_delayed_work_sync(&priv->alarm_poll_work);
+ mpq8646_debugfs_unregister(priv);
+}
+
+static struct i2c_driver mpq8646_driver = {
+ .driver = {
+ .name = "mpq8646",
+ .of_match_table = of_match_ptr(mpq8646_of_match),
+ },
+ .probe = mpq8646_probe,
+ .remove = mpq8646_remove,
+ .id_table = mpq8646_id,
+};
+
+module_i2c_driver(mpq8646_driver);
+
+MODULE_AUTHOR("Vincent Jardin <vjardin@free.fr>");
+MODULE_DESCRIPTION("PMBus driver for MPS MPQ8646 (extended observability)");
+MODULE_LICENSE("GPL");
+MODULE_IMPORT_NS("PMBUS");
--
2.43.0
^ permalink raw reply related [flat|nested] 11+ messages in thread