[PATCH v4 0/4] ARM: dts: vf: Iris carrier board for the Colibri VF50 and VF61

[PATCH v4 0/4] ARM: dts: vf: Iris carrier board for the Colibri VF50 and VF61

[Mehmet Fide]

From: Mehmet Fide <mehmet.fide@screeningeagle.com>

This adds a device tree for the Toradex Iris carrier board carrying the
Vybrid Colibri modules, plus two small preparatory patches for the
module-level dtsi that the i.MX Colibri variants already had.

Everything was tested on a Colibri VF50 on an Iris V1.1 running 6.18.

Changes in v4:
- gpio-line-names packed four per line (Frank Li)
- keep the EXT_IO pin group applied next to the carrier hog group
  instead of overwriting pinctrl-0 in the Iris dtsi, verified in
  pinmux-pins on hardware (Sashiko review)
- enable pwm0/pwm1 like the evaluation board does, so the dts matches
  the commit message; both chips register on hardware (Sashiko review)
- the compatibles keep their hyphens; Krzysztof asked for hyphens in
  every newly introduced compatible in the v2 review

Changes in v3, following Krzysztof's review:
- fold the Iris compatibles into the existing -on-eval enum entries
- use hyphens in the newly introduced compatibles
- drop the fixed 5V regulator that only fed the VBUS regulator
- sent as a fresh thread instead of in reply to v2

Changes in v2:
- add the dt-bindings patch for the new compatibles
- describe the USB host VBUS regulator instead of hogging USBH_PEN

Mehmet Fide (4):
  ARM: dts: vf-colibri: apply the EXT_IO pin group
  ARM: dts: vf-colibri: name the SODIMM gpio lines
  dt-bindings: arm: fsl: add the Colibri VF50 and VF61 on Iris
  ARM: dts: vf: add Iris carrier board support for Colibri VF50 and VF61

 .../devicetree/bindings/arm/fsl.yaml          |  12 +-
 arch/arm/boot/dts/nxp/vf/Makefile             |   2 +
 arch/arm/boot/dts/nxp/vf/vf-colibri-iris.dtsi | 126 ++++++++++++++++++
 arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi      |  56 ++++++++
 .../boot/dts/nxp/vf/vf500-colibri-iris.dts    |  14 ++
 .../boot/dts/nxp/vf/vf610-colibri-iris.dts    |  14 ++
 6 files changed, 220 insertions(+), 4 deletions(-)
 create mode 100644 arch/arm/boot/dts/nxp/vf/vf-colibri-iris.dtsi
 create mode 100644 arch/arm/boot/dts/nxp/vf/vf500-colibri-iris.dts
 create mode 100644 arch/arm/boot/dts/nxp/vf/vf610-colibri-iris.dts


base-commit: 3d6d817622b0a9721e3cc404df3469171582be13
-- 
2.54.0

[PATCH v4 1/4] ARM: dts: vf-colibri: apply the EXT_IO pin group

[Mehmet Fide]

From: Mehmet Fide <mehmet.fide@screeningeagle.com>

pinctrl_gpio_ext describes the three Colibri EXT_IO pins, but no node
references it, so the pin controller never applies it and the pads keep
whatever mux and bias they came up with. It is the only pin group in the
Vybrid Colibri device trees that is defined and never used.

The three pins are GPIOs on gpio2 and belong to no device, so hog the
group on that controller. Referencing it from &iomuxc would work too, but
the pin controller would then depend on one of its own children, which
fw_devlink reports as a dependency cycle.

Signed-off-by: Mehmet Fide <mehmet.fide@screeningeagle.com>
---
 arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi b/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi
index 98f9ee1b0030..74afc7b0d74b 100644
--- a/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi
@@ -170,6 +170,15 @@ &usbphy1 {
 	status = "okay";
 };
 
+&gpio2 {
+	/*
+	 * EXT_IO_0..2 belong to no device, so hog the pin group here rather
+	 * than on the pin controller, which would depend on its own child.
+	 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_gpio_ext>;
+};
+
 &iomuxc {
 	pinctrl_flexcan0: can0grp {
 		fsl,pins = <
-- 
2.54.0

[PATCH v4 2/4] ARM: dts: vf-colibri: name the SODIMM gpio lines

[Mehmet Fide]

From: Mehmet Fide <mehmet.fide@screeningeagle.com>

The Colibri modules expose most of their GPIOs on numbered SODIMM pins,
and the i.MX ones already carry those numbers as gpio-line-names, so the
gpiod tools print SODIMM_43 rather than a bank and an offset. Do the same
for the Vybrid modules.

The 99 names come from the pinout table of the Colibri VFxx datasheet
(Toradex 101355). Verified on a Colibri VF50, where gpioinfo now names
every pin the datasheet lists.

Signed-off-by: Mehmet Fide <mehmet.fide@screeningeagle.com>
---
 arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi | 47 ++++++++++++++++++++++++
 1 file changed, 47 insertions(+)

diff --git a/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi b/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi
index 74afc7b0d74b..a9269857df2c 100644
--- a/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi
+++ b/arch/arm/boot/dts/nxp/vf/vf-colibri.dtsi
@@ -170,6 +170,44 @@ &usbphy1 {
 	status = "okay";
 };
 
+&gpio0 {
+	gpio-line-names = "", "", "SODIMM_89", "",
+			  "", "SODIMM_102", "SODIMM_18", "SODIMM_134",
+			  "SODIMM_16", "SODIMM_14", "SODIMM_23", "",
+			  "", "", "SODIMM_47", "SODIMM_190",
+			  "SODIMM_192", "SODIMM_49", "SODIMM_51", "SODIMM_53",
+			  "SODIMM_37", "SODIMM_29", "", "SODIMM_30",
+			  "SODIMM_20", "SODIMM_24", "SODIMM_21", "SODIMM_19",
+			  "SODIMM_94", "SODIMM_81", "SODIMM_28";
+};
+
+&gpio1 {
+	gpio-line-names = "SODIMM_35", "SODIMM_33", "SODIMM_27", "SODIMM_25",
+			  "SODIMM_196", "SODIMM_194", "SODIMM_63", "SODIMM_55",
+			  "SODIMM_65", "SODIMM_45", "SODIMM_43", "SODIMM_73",
+			  "SODIMM_77", "SODIMM_71", "SODIMM_98", "SODIMM_101",
+			  "SODIMM_103", "SODIMM_79", "SODIMM_97", "",
+			  "", "SODIMM_85", "", "",
+			  "", "", "", "",
+			  "", "", "", "SODIMM_106";
+};
+
+&gpio3 {
+	gpio-line-names = "SODIMM_105", "", "SODIMM_93", "",
+			  "", "", "", "SODIMM_95",
+			  "SODIMM_22", "SODIMM_68", "SODIMM_82", "SODIMM_56",
+			  "SODIMM_131", "SODIMM_44", "SODIMM_144", "SODIMM_146",
+			  "SODIMM_52", "SODIMM_54", "SODIMM_66", "SODIMM_64",
+			  "SODIMM_57", "SODIMM_61", "SODIMM_140", "SODIMM_142",
+			  "SODIMM_80", "SODIMM_46", "SODIMM_62", "SODIMM_48",
+			  "SODIMM_74", "SODIMM_50", "SODIMM_136", "SODIMM_138";
+};
+
+&gpio4 {
+	gpio-line-names = "SODIMM_76", "SODIMM_70", "SODIMM_60", "SODIMM_58",
+			  "SODIMM_78", "SODIMM_72", "SODIMM_96";
+};
+
 &gpio2 {
 	/*
 	 * EXT_IO_0..2 belong to no device, so hog the pin group here rather
@@ -177,6 +215,15 @@ &gpio2 {
 	 */
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_gpio_ext>;
+
+	gpio-line-names = "SODIMM_69", "SODIMM_99", "SODIMM_104", "SODIMM_107",
+			  "SODIMM_127", "SODIMM_184", "SODIMM_186", "",
+			  "", "", "", "",
+			  "", "", "", "SODIMM_38",
+			  "SODIMM_36", "SODIMM_34", "SODIMM_32", "SODIMM_129",
+			  "SODIMM_86", "SODIMM_90", "SODIMM_92", "SODIMM_88",
+			  "SODIMM_133", "SODIMM_135", "SODIMM_188", "SODIMM_75",
+			  "SODIMM_100";
 };
 
 &iomuxc {
-- 
2.54.0

[PATCH v4 3/4] dt-bindings: arm: fsl: add the Colibri VF50 and VF61 on Iris

[Mehmet Fide]

From: Mehmet Fide <mehmet.fide@screeningeagle.com>

The Iris is a small off-the-shelf carrier board for the Colibri
family. Extend the evaluation board entries with the compatibles for
a Colibri VF50 or VF61 sitting on it.

Signed-off-by: Mehmet Fide <mehmet.fide@screeningeagle.com>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 12 ++++++++----
 1 file changed, 8 insertions(+), 4 deletions(-)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 86876311ec59..6f95c17b363c 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1705,9 +1705,11 @@ properties:
               - fsl,vf610
               - fsl,vf610m4
 
-      - description: Toradex Colibri VF50 Module on Colibri Evaluation Board
+      - description: Toradex Colibri VF50 Module on a carrier board
         items:
-          - const: toradex,vf500-colibri_vf50-on-eval
+          - enum:
+              - toradex,vf500-colibri_vf50-on-eval
+              - toradex,vf500-colibri-vf50-on-iris
           - const: toradex,vf500-colibri_vf50
           - const: fsl,vf500
 
@@ -1719,9 +1721,11 @@ properties:
               - phytec,vf610-cosmic       # PHYTEC Cosmic/Cosmic+ Board
           - const: fsl,vf610
 
-      - description: Toradex Colibri VF61 Module on Colibri Evaluation Board
+      - description: Toradex Colibri VF61 Module on a carrier board
         items:
-          - const: toradex,vf610-colibri_vf61-on-eval
+          - enum:
+              - toradex,vf610-colibri_vf61-on-eval
+              - toradex,vf610-colibri-vf61-on-iris
           - const: toradex,vf610-colibri_vf61
           - const: fsl,vf610
 
-- 
2.54.0

[PATCH v4 4/4] ARM: dts: vf: add Iris carrier board support for Colibri VF50 and VF61

[Mehmet Fide]

From: Mehmet Fide <mehmet.fide@screeningeagle.com>

The Iris is a small off-the-shelf carrier board for the Colibri
family. Describe what the board itself provides: Ethernet, one USB
host and one OTG port, the pin header UARTs, i2c with the carrier
RTC on it, the PWM pins on the X16 header, SPI and the microSD slot.
The host port gets its VBUS through a regulator on SODIMM 129, and
the two GPIOs that turn the RS232 transceivers on, SODIMM 102 and
104, are hogged. The touchscreen is an add-on rather than part of
the board, so it is left out.

This describes an Iris V1.1. A V2.0 carries the same signals on the
same pins; what it adds, and what this does not describe, is the
regulator on SODIMM 100 that can cut power to the uSD slot.

Tested on a Colibri VF50 on an Iris V1.1 running 6.18: Ethernet at
100Mbps/Full, a USB dongle enumerating once the VBUS regulator is in
place, the RTC read back over i2c0, all three UARTs, the SPI
controller registering, both PWM chips registering, the microSD
slot, the EXT_IO pin group still applied next to the carrier hog
group, and both hogs holding their pins.

Signed-off-by: Mehmet Fide <mehmet.fide@screeningeagle.com>
---
 arch/arm/boot/dts/nxp/vf/Makefile             |   2 +
 arch/arm/boot/dts/nxp/vf/vf-colibri-iris.dtsi | 126 ++++++++++++++++++
 .../boot/dts/nxp/vf/vf500-colibri-iris.dts    |  14 ++
 .../boot/dts/nxp/vf/vf610-colibri-iris.dts    |  14 ++
 4 files changed, 156 insertions(+)
 create mode 100644 arch/arm/boot/dts/nxp/vf/vf-colibri-iris.dtsi
 create mode 100644 arch/arm/boot/dts/nxp/vf/vf500-colibri-iris.dts
 create mode 100644 arch/arm/boot/dts/nxp/vf/vf610-colibri-iris.dts

diff --git a/arch/arm/boot/dts/nxp/vf/Makefile b/arch/arm/boot/dts/nxp/vf/Makefile
index 0a4a7f9dd43e..47be8bc318e2 100644
--- a/arch/arm/boot/dts/nxp/vf/Makefile
+++ b/arch/arm/boot/dts/nxp/vf/Makefile
@@ -1,8 +1,10 @@
 # SPDX-License-Identifier: GPL-2.0
 dtb-$(CONFIG_SOC_VF610) += \
 	vf500-colibri-eval-v3.dtb \
+	vf500-colibri-iris.dtb \
 	vf610-bk4.dtb \
 	vf610-colibri-eval-v3.dtb \
+	vf610-colibri-iris.dtb \
 	vf610m4-colibri.dtb \
 	vf610-cosmic.dtb \
 	vf610m4-cosmic.dtb \
diff --git a/arch/arm/boot/dts/nxp/vf/vf-colibri-iris.dtsi b/arch/arm/boot/dts/nxp/vf/vf-colibri-iris.dtsi
new file mode 100644
index 000000000000..36e34dd766ae
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/vf/vf-colibri-iris.dtsi
@@ -0,0 +1,126 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2026 Mehmet Fide
+ *
+ * Toradex Iris carrier board V1.1, common part for Colibri VF50 and VF61.
+ *
+ * The Colibri modules are pin compatible, so the carrier signals sit on the
+ * same SODIMM pins as they do for the i.MX modules, whose Iris device trees
+ * are already upstream. The two SODIMM pins below are taken from the Colibri
+ * VFxx datasheet (102 -> PTA12 -> PORT0[5], 104 -> PTD28 -> PORT2[2]).
+ *
+ * An Iris V2.0 carries the same signals on the same pins, so everything here
+ * works on it as well. What it adds is a regulator on SODIMM 100 that can cut
+ * power to the uSD slot, which this file does not describe.
+ */
+
+/ {
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_usbh_vbus: regulator-usbh-vbus {
+		compatible = "regulator-fixed";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbh1_reg>;
+		regulator-name = "VCC_USB[1-4]";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio2 19 GPIO_ACTIVE_LOW>;	/* SODIMM 129, USBH_PEN */
+	};
+};
+
+&gpio0 {
+	/*
+	 * The RS232 transceivers on the carrier are switched on by these two
+	 * lines. Delete the hog to turn a transceiver off from userspace.
+	 * The pin group belongs to the gpio controller rather than to iomuxc,
+	 * which would depend on its own child and log a dependency cycle.
+	 */
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_iris_uart1_tx_on>;
+
+	uart1-tx-on-hog {
+		gpio-hog;
+		gpios = <5 GPIO_ACTIVE_HIGH>;	/* SODIMM 102 */
+		output-high;
+	};
+};
+
+&gpio2 {
+	pinctrl-names = "default";
+	/* keep the EXT_IO group from vf-colibri.dtsi alongside ours */
+	pinctrl-0 = <&pinctrl_gpio_ext>, <&pinctrl_iris_uart25_tx_on>;
+
+	uart25-tx-on-hog {
+		gpio-hog;
+		gpios = <2 GPIO_ACTIVE_HIGH>;	/* SODIMM 104 */
+		output-high;
+	};
+};
+
+&iomuxc {
+	pinctrl_iris_uart1_tx_on: irisuart1txongrp {
+		fsl,pins = <
+			VF610_PAD_PTA12__GPIO_5		0x22ef
+		>;
+	};
+
+	pinctrl_iris_uart25_tx_on: irisuart25txongrp {
+		fsl,pins = <
+			VF610_PAD_PTD28__GPIO_66	0x22ef
+		>;
+	};
+};
+
+/* Colibri SSP, on the extension connector */
+&dspi1 {
+	status = "okay";
+};
+
+&esdhc1 {
+	status = "okay";
+};
+
+&fec1 {
+	status = "okay";
+};
+
+&pwm0 {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	/* M41T0M6 real time clock on the carrier */
+	rtc@68 {
+		compatible = "st,m41t0";
+		reg = <0x68>;
+	};
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&uart1 {
+	status = "okay";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usbdev0 {
+	status = "okay";
+};
+
+&usbh1 {
+	vbus-supply = <&reg_usbh_vbus>;
+	status = "okay";
+};
diff --git a/arch/arm/boot/dts/nxp/vf/vf500-colibri-iris.dts b/arch/arm/boot/dts/nxp/vf/vf500-colibri-iris.dts
new file mode 100644
index 000000000000..aa91537cab37
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/vf/vf500-colibri-iris.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2026 Mehmet Fide
+ */
+
+/dts-v1/;
+#include "vf500-colibri.dtsi"
+#include "vf-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri VF50 on Iris Carrier Board";
+	compatible = "toradex,vf500-colibri-vf50-on-iris", "toradex,vf500-colibri_vf50",
+		     "fsl,vf500";
+};
diff --git a/arch/arm/boot/dts/nxp/vf/vf610-colibri-iris.dts b/arch/arm/boot/dts/nxp/vf/vf610-colibri-iris.dts
new file mode 100644
index 000000000000..7db5aa490966
--- /dev/null
+++ b/arch/arm/boot/dts/nxp/vf/vf610-colibri-iris.dts
@@ -0,0 +1,14 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright 2026 Mehmet Fide
+ */
+
+/dts-v1/;
+#include "vf610-colibri.dtsi"
+#include "vf-colibri-iris.dtsi"
+
+/ {
+	model = "Toradex Colibri VF61 on Iris Carrier Board";
+	compatible = "toradex,vf610-colibri-vf61-on-iris", "toradex,vf610-colibri_vf61",
+		     "fsl,vf610";
+};
-- 
2.54.0