[PATCH v3 1/5] riscv: dts: spacemit: k3: move USB3 phy to board level

[PATCH v3 1/5] riscv: dts: spacemit: k3: move USB3 phy to board level

[Aurelien Jarno]

On the SpacemiT K3 SoC, the combo phy provides 8 lines that can
either be used for PCIe or USB3, depending on its configuration
(spacemit,apmu). This configuration is defined at the board level, and
assigning a phy line to a USB3 controller while it is configured as PCIe
results in an "Invalid PHY mode" error.

Move the USB3 phy at the board level, the as it is done for the
submitted PCIe controller [1]. Keep the USB2 phy at the SoC level as
there is one phy per USB controller.

[1] https://lore.kernel.org/20260727094726.890179-3-inochiama@gmail.com/

Fixes: 46380e4b1534c1626cecd7f4d0abb5e0cce09af6 ("riscv: dts: spacemit: k3: add USB controller and USB phy support")
Cc: Inochi Amaoto <inochiama@gmail.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
---
 arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 3 +++
 arch/riscv/boot/dts/spacemit/k3.dtsi         | 5 ++---
 2 files changed, 5 insertions(+), 3 deletions(-)

diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
index b084a35aa00e..171bd2f40aa6 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
@@ -328,5 +328,8 @@ &usb3d_u2phy {
 };
 
 &usb3d {
+	phys = <&usb3d_u2phy>,
+	       <&combophy 4 PHY_TYPE_USB3>;
+	phy-names = "usb2-phy", "usb3-phy";
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
index c3f2dce0969c..3e24054d2084 100644
--- a/arch/riscv/boot/dts/spacemit/k3.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
@@ -452,9 +452,8 @@ usb3d: usb@81a00000 {
 				 <&syscon_apmu RESET_APMU_USB3_D_VCC>,
 				 <&syscon_apmu RESET_APMU_USB3_D_PHY>;
 			reset-names = "ahb", "vcc", "phy";
-			phys = <&usb3d_u2phy>,
-			       <&combophy 4 PHY_TYPE_USB3>;
-			phy-names = "usb2-phy", "usb3-phy";
+			phys = <&usb3d_u2phy>;
+			phy-names = "usb2-phy";
 			phy_type = "utmi";
 			snps,dis_enblslpm_quirk;
 			snps,dis_u2_susphy_quirk;
-- 
2.53.0

Re: [PATCH v3 1/5] riscv: dts: spacemit: k3: move USB3 phy to board level

[Inochi Amaoto]

On Wed, Aug 19, 2026 at 06:15:42PM +0200, Aurelien Jarno wrote:
> On the SpacemiT K3 SoC, the combo phy provides 8 lines that can
> either be used for PCIe or USB3, depending on its configuration
> (spacemit,apmu). This configuration is defined at the board level, and
> assigning a phy line to a USB3 controller while it is configured as PCIe
> results in an "Invalid PHY mode" error.
> 
> Move the USB3 phy at the board level, the as it is done for the
> submitted PCIe controller [1]. Keep the USB2 phy at the SoC level as
> there is one phy per USB controller.
> 
> [1] https://lore.kernel.org/20260727094726.890179-3-inochiama@gmail.com/
> 
> Fixes: 46380e4b1534c1626cecd7f4d0abb5e0cce09af6 ("riscv: dts: spacemit: k3: add USB controller and USB phy support")
> Cc: Inochi Amaoto <inochiama@gmail.com>
> Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
> ---
>  arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 3 +++
>  arch/riscv/boot/dts/spacemit/k3.dtsi         | 5 ++---
>  2 files changed, 5 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> index b084a35aa00e..171bd2f40aa6 100644
> --- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> +++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> @@ -328,5 +328,8 @@ &usb3d_u2phy {
>  };
>  
>  &usb3d {
> +	phys = <&usb3d_u2phy>,
> +	       <&combophy 4 PHY_TYPE_USB3>;
> +	phy-names = "usb2-phy", "usb3-phy";
>  	status = "okay";
>  };
> diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
> index c3f2dce0969c..3e24054d2084 100644
> --- a/arch/riscv/boot/dts/spacemit/k3.dtsi
> +++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
> @@ -452,9 +452,8 @@ usb3d: usb@81a00000 {
>  				 <&syscon_apmu RESET_APMU_USB3_D_VCC>,
>  				 <&syscon_apmu RESET_APMU_USB3_D_PHY>;
>  			reset-names = "ahb", "vcc", "phy";

> -			phys = <&usb3d_u2phy>,
> -			       <&combophy 4 PHY_TYPE_USB3>;
> -			phy-names = "usb2-phy", "usb3-phy";
> +			phys = <&usb3d_u2phy>;
> +			phy-names = "usb2-phy";

I suggest removing this completely as we can not determine the
phy we used. I think it is suitable for setting this in board
file only

Regards,
Inochi

>  			phy_type = "utmi";
>  			snps,dis_enblslpm_quirk;
>  			snps,dis_u2_susphy_quirk;
> -- 
> 2.53.0
> 
> 
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv

Re: [PATCH v3 1/5] riscv: dts: spacemit: k3: move USB3 phy to board level

[Aurelien Jarno]

On 2026-08-22 10:17, Inochi Amaoto wrote:
> On Wed, Aug 19, 2026 at 06:15:42PM +0200, Aurelien Jarno wrote:
> > On the SpacemiT K3 SoC, the combo phy provides 8 lines that can
> > either be used for PCIe or USB3, depending on its configuration
> > (spacemit,apmu). This configuration is defined at the board level, and
> > assigning a phy line to a USB3 controller while it is configured as PCIe
> > results in an "Invalid PHY mode" error.
> > 
> > Move the USB3 phy at the board level, the as it is done for the
> > submitted PCIe controller [1]. Keep the USB2 phy at the SoC level as
> > there is one phy per USB controller.
> > 
> > [1] https://lore.kernel.org/20260727094726.890179-3-inochiama@gmail.com/
> > 
> > Fixes: 46380e4b1534c1626cecd7f4d0abb5e0cce09af6 ("riscv: dts: spacemit: k3: add USB controller and USB phy support")
> > Cc: Inochi Amaoto <inochiama@gmail.com>
> > Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
> > ---
> >  arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 3 +++
> >  arch/riscv/boot/dts/spacemit/k3.dtsi         | 5 ++---
> >  2 files changed, 5 insertions(+), 3 deletions(-)
> > 
> > diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> > index b084a35aa00e..171bd2f40aa6 100644
> > --- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> > +++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> > @@ -328,5 +328,8 @@ &usb3d_u2phy {
> >  };
> >  
> >  &usb3d {
> > +	phys = <&usb3d_u2phy>,
> > +	       <&combophy 4 PHY_TYPE_USB3>;
> > +	phy-names = "usb2-phy", "usb3-phy";
> >  	status = "okay";
> >  };
> > diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
> > index c3f2dce0969c..3e24054d2084 100644
> > --- a/arch/riscv/boot/dts/spacemit/k3.dtsi
> > +++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
> > @@ -452,9 +452,8 @@ usb3d: usb@81a00000 {
> >  				 <&syscon_apmu RESET_APMU_USB3_D_VCC>,
> >  				 <&syscon_apmu RESET_APMU_USB3_D_PHY>;
> >  			reset-names = "ahb", "vcc", "phy";
> 
> > -			phys = <&usb3d_u2phy>,
> > -			       <&combophy 4 PHY_TYPE_USB3>;
> > -			phy-names = "usb2-phy", "usb3-phy";
> > +			phys = <&usb3d_u2phy>;
> > +			phy-names = "usb2-phy";
> 
> I suggest removing this completely as we can not determine the
> phy we used. I think it is suitable for setting this in board
> file only

Yes, moving all the phy definition to the board level is an option. I 
decided to keep the USB2 phy at the SoC level, because contrary to the 
USB3 phys, there is a one to one mapping between the controller and the 
phy. Do you think it is a wrong assumption?

Regards
Aurelien

-- 
Aurelien Jarno                          GPG: 4096R/1DDD8C9B
aurelien@aurel32.net                     http://aurel32.net

Re: [PATCH v3 1/5] riscv: dts: spacemit: k3: move USB3 phy to board level

[Inochi Amaoto]

On Sat, Aug 22, 2026 at 11:37:44AM +0200, Aurelien Jarno wrote:
> On 2026-08-22 10:17, Inochi Amaoto wrote:
> > On Wed, Aug 19, 2026 at 06:15:42PM +0200, Aurelien Jarno wrote:
> > > On the SpacemiT K3 SoC, the combo phy provides 8 lines that can
> > > either be used for PCIe or USB3, depending on its configuration
> > > (spacemit,apmu). This configuration is defined at the board level, and
> > > assigning a phy line to a USB3 controller while it is configured as PCIe
> > > results in an "Invalid PHY mode" error.
> > > 
> > > Move the USB3 phy at the board level, the as it is done for the
> > > submitted PCIe controller [1]. Keep the USB2 phy at the SoC level as
> > > there is one phy per USB controller.
> > > 
> > > [1] https://lore.kernel.org/20260727094726.890179-3-inochiama@gmail.com/
> > > 
> > > Fixes: 46380e4b1534c1626cecd7f4d0abb5e0cce09af6 ("riscv: dts: spacemit: k3: add USB controller and USB phy support")
> > > Cc: Inochi Amaoto <inochiama@gmail.com>
> > > Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
> > > ---
> > >  arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 3 +++
> > >  arch/riscv/boot/dts/spacemit/k3.dtsi         | 5 ++---
> > >  2 files changed, 5 insertions(+), 3 deletions(-)
> > > 
> > > diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> > > index b084a35aa00e..171bd2f40aa6 100644
> > > --- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> > > +++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> > > @@ -328,5 +328,8 @@ &usb3d_u2phy {
> > >  };
> > >  
> > >  &usb3d {
> > > +	phys = <&usb3d_u2phy>,
> > > +	       <&combophy 4 PHY_TYPE_USB3>;
> > > +	phy-names = "usb2-phy", "usb3-phy";
> > >  	status = "okay";
> > >  };
> > > diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
> > > index c3f2dce0969c..3e24054d2084 100644
> > > --- a/arch/riscv/boot/dts/spacemit/k3.dtsi
> > > +++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
> > > @@ -452,9 +452,8 @@ usb3d: usb@81a00000 {
> > >  				 <&syscon_apmu RESET_APMU_USB3_D_VCC>,
> > >  				 <&syscon_apmu RESET_APMU_USB3_D_PHY>;
> > >  			reset-names = "ahb", "vcc", "phy";
> > 
> > > -			phys = <&usb3d_u2phy>,
> > > -			       <&combophy 4 PHY_TYPE_USB3>;
> > > -			phy-names = "usb2-phy", "usb3-phy";
> > > +			phys = <&usb3d_u2phy>;
> > > +			phy-names = "usb2-phy";
> > 
> > I suggest removing this completely as we can not determine the
> > phy we used. I think it is suitable for setting this in board
> > file only
> 
> Yes, moving all the phy definition to the board level is an option. I 
> decided to keep the USB2 phy at the SoC level, because contrary to the 
> USB3 phys, there is a one to one mapping between the controller and the 
> phy. Do you think it is a wrong assumption?
> 

By default, I prefer to make the forgotten thing as an error in
validation for any flexible field. If you leave the default value,
the forgotten field will lead to a downgrade hardware (or maybe
broken hardware). So I prefer to remove this rather than give a
default value.

Regards,
Inochi

Re: [PATCH v3 1/5] riscv: dts: spacemit: k3: move USB3 phy to board level

[Aurelien Jarno]

On 2026-08-22 20:33, Inochi Amaoto wrote:
> On Sat, Aug 22, 2026 at 11:37:44AM +0200, Aurelien Jarno wrote:
> > On 2026-08-22 10:17, Inochi Amaoto wrote:
> > > On Wed, Aug 19, 2026 at 06:15:42PM +0200, Aurelien Jarno wrote:
> > > > On the SpacemiT K3 SoC, the combo phy provides 8 lines that can
> > > > either be used for PCIe or USB3, depending on its configuration
> > > > (spacemit,apmu). This configuration is defined at the board level, and
> > > > assigning a phy line to a USB3 controller while it is configured as PCIe
> > > > results in an "Invalid PHY mode" error.
> > > > 
> > > > Move the USB3 phy at the board level, the as it is done for the
> > > > submitted PCIe controller [1]. Keep the USB2 phy at the SoC level as
> > > > there is one phy per USB controller.
> > > > 
> > > > [1] https://lore.kernel.org/20260727094726.890179-3-inochiama@gmail.com/
> > > > 
> > > > Fixes: 46380e4b1534c1626cecd7f4d0abb5e0cce09af6 ("riscv: dts: spacemit: k3: add USB controller and USB phy support")
> > > > Cc: Inochi Amaoto <inochiama@gmail.com>
> > > > Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
> > > > ---
> > > >  arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 3 +++
> > > >  arch/riscv/boot/dts/spacemit/k3.dtsi         | 5 ++---
> > > >  2 files changed, 5 insertions(+), 3 deletions(-)
> > > > 
> > > > diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> > > > index b084a35aa00e..171bd2f40aa6 100644
> > > > --- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> > > > +++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> > > > @@ -328,5 +328,8 @@ &usb3d_u2phy {
> > > >  };
> > > >  
> > > >  &usb3d {
> > > > +	phys = <&usb3d_u2phy>,
> > > > +	       <&combophy 4 PHY_TYPE_USB3>;
> > > > +	phy-names = "usb2-phy", "usb3-phy";
> > > >  	status = "okay";
> > > >  };
> > > > diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
> > > > index c3f2dce0969c..3e24054d2084 100644
> > > > --- a/arch/riscv/boot/dts/spacemit/k3.dtsi
> > > > +++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
> > > > @@ -452,9 +452,8 @@ usb3d: usb@81a00000 {
> > > >  				 <&syscon_apmu RESET_APMU_USB3_D_VCC>,
> > > >  				 <&syscon_apmu RESET_APMU_USB3_D_PHY>;
> > > >  			reset-names = "ahb", "vcc", "phy";
> > > 
> > > > -			phys = <&usb3d_u2phy>,
> > > > -			       <&combophy 4 PHY_TYPE_USB3>;
> > > > -			phy-names = "usb2-phy", "usb3-phy";
> > > > +			phys = <&usb3d_u2phy>;
> > > > +			phy-names = "usb2-phy";
> > > 
> > > I suggest removing this completely as we can not determine the
> > > phy we used. I think it is suitable for setting this in board
> > > file only
> > 
> > Yes, moving all the phy definition to the board level is an option. I 
> > decided to keep the USB2 phy at the SoC level, because contrary to the 
> > USB3 phys, there is a one to one mapping between the controller and the 
> > phy. Do you think it is a wrong assumption?
> > 
> 
> By default, I prefer to make the forgotten thing as an error in
> validation for any flexible field. If you leave the default value,
> the forgotten field will lead to a downgrade hardware (or maybe
> broken hardware). So I prefer to remove this rather than give a
> default value.

Ok, thanks for the feedback, i'll fix that in the v4.

Regards
Aurelien

-- 
Aurelien Jarno                          GPG: 4096R/1DDD8C9B
aurelien@aurel32.net                     http://aurel32.net

[PATCH v3 2/5] riscv: dts: spacemit: k3: add USB3 B and C controllers for Pico-ITX board

[Aurelien Jarno]

The SpacemiT K3 has 4 USB3 controllers labelled A to D.

On the K3 Pico-ITX board, the controllers B and C are used in USB2 mode
only respectively for the M.2 B-Key slot and for the RTL8852BE Bluetooth
controller.

Add the two controller nodes, the two corresponding USB2 PHY nodes, and
enable them on the K3 Pico-ITX board.

Tested-by: Anirudh Srinivasan <asrinivasan@oss.tenstorrent.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
---
 arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 18 ++++++
 arch/riscv/boot/dts/spacemit/k3.dtsi         | 64 ++++++++++++++++++++
 2 files changed, 82 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
index 171bd2f40aa6..e932e464e645 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
@@ -323,6 +323,24 @@ &usb2_phy {
 	status = "okay";
 };
 
+&usb3b {
+	maximum-speed = "high-speed";
+	status = "okay";
+};
+
+&usb3b_u2phy {
+	status = "okay";
+};
+
+&usb3c {
+	maximum-speed = "high-speed";
+	status = "okay";
+};
+
+&usb3c_u2phy {
+	status = "okay";
+};
+
 &usb3d_u2phy {
 	status = "okay";
 };
diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
index 3e24054d2084..f885e2b4207b 100644
--- a/arch/riscv/boot/dts/spacemit/k3.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
@@ -441,6 +441,70 @@ soc: soc {
 		dma-noncoherent;
 		ranges;
 
+		usb3b: usb@81400000 {
+			compatible = "spacemit,k3-dwc3";
+			reg = <0x0 0x81400000 0x0 0x10000>;
+			interrupts = <125 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-parent = <&saplic>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTB_BUS>;
+			clock-names = "usbdrd30";
+			resets = <&syscon_apmu RESET_APMU_USB3_B_AHB>,
+				 <&syscon_apmu RESET_APMU_USB3_B_VCC>,
+				 <&syscon_apmu RESET_APMU_USB3_B_PHY>;
+			reset-names = "ahb", "vcc", "phy";
+			phys = <&usb3b_u2phy>;
+			phy-names = "usb2-phy";
+			phy_type = "utmi";
+			snps,dis_enblslpm_quirk;
+			snps,dis_u2_susphy_quirk;
+			snps,dis_u3_susphy_quirk;
+			snps,dis-del-phy-power-chg-quirk;
+			snps,dis-tx-ipgap-linecheck-quirk;
+			snps,parkmode-disable-ss-quirk;
+			dr_mode = "host";
+			status = "disabled";
+		};
+
+		usb3b_u2phy: phy@81500000 {
+			compatible = "spacemit,k3-usb2-phy";
+			reg = <0x0 0x81500000 0x0 0x200>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTB_BUS>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
+		usb3c: usb@81700000 {
+			compatible = "spacemit,k3-dwc3";
+			reg = <0x0 0x81700000 0x0 0x10000>;
+			interrupts = <148 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-parent = <&saplic>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTC_BUS>;
+			clock-names = "usbdrd30";
+			resets = <&syscon_apmu RESET_APMU_USB3_C_AHB>,
+				 <&syscon_apmu RESET_APMU_USB3_C_VCC>,
+				 <&syscon_apmu RESET_APMU_USB3_C_PHY>;
+			reset-names = "ahb", "vcc", "phy";
+			phys = <&usb3c_u2phy>;
+			phy-names = "usb2-phy";
+			phy_type = "utmi";
+			snps,dis_enblslpm_quirk;
+			snps,dis_u2_susphy_quirk;
+			snps,dis_u3_susphy_quirk;
+			snps,dis-del-phy-power-chg-quirk;
+			snps,dis-tx-ipgap-linecheck-quirk;
+			snps,parkmode-disable-ss-quirk;
+			dr_mode = "host";
+			status = "disabled";
+		};
+
+		usb3c_u2phy: phy@81800000 {
+			compatible = "spacemit,k3-usb2-phy";
+			reg = <0x0 0x81800000 0x0 0x200>;
+			clocks = <&syscon_apmu CLK_APMU_USB3_PORTC_BUS>;
+			#phy-cells = <0>;
+			status = "disabled";
+		};
+
 		usb3d: usb@81a00000 {
 			compatible = "spacemit,k3-dwc3";
 			reg = <0x0 0x81a00000 0x0 0x10000>;
-- 
2.53.0

[PATCH v3 3/5] riscv: dts: spacemit: k3: add rfkill node for Bluetooth on Pico-ITX board

[Aurelien Jarno]

On the K3 Pico-ITX board, by default the GPIO pin that connects to the
RTL8852BE Bluetooth enable signal is driven low, resulting in
impossibility to use Bluetooth. Add a DT node to expose it as an RFKILL
device, which lets the Bluetooth driver or userspace toggle it as
required.

Tested-by: Anirudh Srinivasan <asrinivasan@oss.tenstorrent.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
---
 arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
index e932e464e645..d2e8df5ebeec 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
@@ -43,6 +43,13 @@ reg_aux_vcc5v: regulator-aux-vcc5v {
 		regulator-max-microvolt = <5000000>;
 		regulator-always-on;
 	};
+
+	rfkill-usb-bt {
+		compatible = "rfkill-gpio";
+		label = "rfkill-usb-bt";
+		radio-type = "bluetooth";
+		shutdown-gpios = <&gpio 0 30 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &i2c2 {
-- 
2.53.0

[PATCH v3 4/5] riscv: dts: spacemit: k3: add rfkill node for WLAN on the K3 Pico-ITX board

[Aurelien Jarno]

On the K3 Pico-ITX board, by default the GPIO pin that connects to the
RTL8852BE WLAN enable signal is driven low, resulting in impossibility
to connect to any network. Add a DT node to expose it as an RFKILL
device, which lets the WLAN driver or userspace toggle it as required.

Tested-by: Anirudh Srinivasan <asrinivasan@oss.tenstorrent.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
---
 arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
index d2e8df5ebeec..68f8224eabcd 100644
--- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
+++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
@@ -44,6 +44,13 @@ reg_aux_vcc5v: regulator-aux-vcc5v {
 		regulator-always-on;
 	};
 
+	rfkill-pcie-wlan {
+		compatible = "rfkill-gpio";
+		label = "rfkill-pcie-wlan";
+		radio-type = "wlan";
+		shutdown-gpios = <&gpio 1 3 GPIO_ACTIVE_HIGH>;
+	};
+
 	rfkill-usb-bt {
 		compatible = "rfkill-gpio";
 		label = "rfkill-usb-bt";
-- 
2.53.0