[PATCH v7 0/5] regulator: Add X-Powers AXP318W PMIC support

[PATCH v7 0/5] regulator: Add X-Powers AXP318W PMIC support

[Jerome Brunet]

This patch series adds support for the X-Powers AXP318W PMIC, which is
used recently on new boards with Allwinner SoCs (the A733).

The PMIC features 9 DCDC buck converters and 28 LDOs, plus the usual ADC,
interrupts, and power key components.
A datasheet can be found linked in this Wiki table:
https://linux-sunxi.org/AXP_PMICs

There was an unclosed topic regarding the handling of LDOs output
voltage being limited to input voltage being provided by the supply.
Chen-Yu noted the min_dropout_uV would be a good fit for that but
the actual minimal dropout value was unknown. I've arbitrarily picked
1uV because it is the minimum the framework supports. Realistically a low
dropout regulator is bound to have some dropout. This choice does the
trick for now and is certain be less restrictive than what it is in
reality.

If anyone has problems because the dropout is actually higher
* it is arguably an HW design error
* it is a good time to let us know what the actual dropout is

Changes in v7:
- Rebased on v7.3-rc1.
- Applied Chen-Yu change requests.
  - More complete register definition all in the MFD change.
  - Add writeable region holes.
  - Fix invertion between short and long press IRQ.
  - Drop confusing comment about DVM.
  - Use MFD_CELL_NAME() for the regulator device.
- Link to v6: https://patch.msgid.link/20260812-axp318-regulator-v6-0-d6b84b55c000@baylibre.com

Changes in v6:
- Apply wording suggestions from Chen-Yu
- Link to v5: https://patch.msgid.link/20260720-axp318-regulator-v5-0-a1afa7ee24f9@baylibre.com

Changes in v5:
- Fix shutdown register offset
- Re-order patches to put fixes first
- Tighten DT regexp around swout
- Other points raised by Sashiko on v4 are unrelated to the addition
  of the AXP318 support and pre-exist the series. They are not
  addressed ATM.
- Link to v4: https://patch.msgid.link/20260717-axp318-regulator-v4-0-50aff97084dd@baylibre.com

Changes in v4:
- Capitalize patch 3 title
- regulator: add support for workmode and poly-phase.
- i2c: fix probe through i2c sysfs
- Link to v3: https://patch.msgid.link/20260717-axp318-regulator-v3-0-779dc1b97dd4@baylibre.com

Changes in v3:
- Correct mess up v2 errors regarding ops and ids.
- Correctly propagate errors when checking axp318 threshold.
- Fix DT binding regex regarding dcdc max ids
- Add missing RTCLDO.
- Remove axp318 PEK MFD cell:
  As pointed out by sashiko, the driver name did not match anything in the
  pek driver. While the device does support some handling of the power
  button, it does not seem to match the existing driver. Register 0x36
  relates to DLDO3, not the power key, as expected by the misc driver.
  Leave this out for now.
- Constify axp313 and axp717 mfd_cells array for consistency.
- Link to v2: https://patch.msgid.link/20260710-axp318-regulator-v2-0-ee5f1c56b49f@baylibre.com

Changes in v2:
- Dropped _NUM_VOLTAGES macros
- Use min_dropout_uV to limit LDO voltage to supplies
- Add bypass mode for EDLO4/5
- Prevent crossing 1.54V threshold for DCDC6/7/8/9
- Link to v1: https://lore.kernel.org/r/20251021112013.2710903-1-andre.przywara@arm.com

---
Andre Przywara (3):
      dt-bindings: mfd: x-powers,axp152: Document AXP318W
      mfd: axp20x: Add support for AXP318W PMIC
      regulator: axp20x: add support for the AXP318W

Jerome Brunet (2):
      mfd: axp20x: Constify axp313 and axp717 cells
      mfd: axp20x-i2c: Fix i2c instantiation

 .../devicetree/bindings/mfd/x-powers,axp152.yaml   |  28 +-
 drivers/mfd/axp20x-i2c.c                           |  26 +-
 drivers/mfd/axp20x-rsb.c                           |   1 +
 drivers/mfd/axp20x.c                               |  93 +++++-
 drivers/regulator/axp20x-regulator.c               | 319 ++++++++++++++++++++-
 include/linux/mfd/axp20x.h                         | 148 +++++++++-
 6 files changed, 589 insertions(+), 26 deletions(-)
---
base-commit: cee9395acd8043be0644b25c34bfa86623f2b935
change-id: 20260710-axp318-regulator-43545ce3261f

Best regards,
--  
Jerome

[PATCH v7 1/5] mfd: axp20x: Constify axp313 and axp717 cells

[Jerome Brunet]

mfd_cells array should generally be const and there does not seem to be
anything against it for the axp313 and axp717.

Constify the mfd_cells array for the axp313 and axp717 to be consistent
with the other supported chips

Acked-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 drivers/mfd/axp20x.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index 50df66de24e0..4d770e718716 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -1055,13 +1055,13 @@ static const struct mfd_cell axp152_cells[] = {
 	},
 };
 
-static struct mfd_cell axp313a_cells[] = {
+static const struct mfd_cell axp313a_cells[] = {
 	/* AXP323 is sometimes paired with AXP717 as sub-PMIC */
 	MFD_CELL_BASIC("axp20x-regulator", NULL, NULL, 0, 1),
 	MFD_CELL_RES("axp313a-pek", axp313a_pek_resources),
 };
 
-static struct mfd_cell axp717_cells[] = {
+static const struct mfd_cell axp717_cells[] = {
 	MFD_CELL_NAME("axp20x-regulator"),
 	MFD_CELL_RES("axp20x-pek", axp717_pek_resources),
 	MFD_CELL_OF("axp717-adc",

-- 
2.53.0

[PATCH v7 2/5] mfd: axp20x-i2c: Fix i2c instantiation

[Jerome Brunet]

Apparently this device never really supported i2c instantiation via
sysfs, because the driver does not even look at the i2c device data,
which are not set. It would only probe if the device matched through DT.

Fix that for correctness, even-though it is probably useless.
Add the missing AXP323 while at it.

Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/r/20260717090209.2A09B1F000E9@smtp.kernel.org
Fixes: 41751b033aaa ("mfd: axp20x-i2c: Add i2c-ids to fix module auto-loading")
Acked-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 drivers/mfd/axp20x-i2c.c   | 24 +++++++++++++-----------
 drivers/mfd/axp20x-rsb.c   |  1 +
 drivers/mfd/axp20x.c       |  1 -
 include/linux/mfd/axp20x.h |  3 +--
 4 files changed, 15 insertions(+), 14 deletions(-)

diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c
index 5c93136f977e..a76bec5604c4 100644
--- a/drivers/mfd/axp20x-i2c.c
+++ b/drivers/mfd/axp20x-i2c.c
@@ -35,6 +35,7 @@ static int axp20x_i2c_probe(struct i2c_client *i2c)
 	axp20x->irq = i2c->irq;
 	dev_set_drvdata(axp20x->dev, axp20x);
 
+	axp20x->variant = (kernel_ulong_t)i2c_get_match_data(i2c);
 	ret = axp20x_match_device(axp20x);
 	if (ret)
 		return ret;
@@ -76,17 +77,18 @@ MODULE_DEVICE_TABLE(of, axp20x_i2c_of_match);
 #endif
 
 static const struct i2c_device_id axp20x_i2c_id[] = {
-	{ "axp152" },
-	{ "axp192" },
-	{ "axp202" },
-	{ "axp209" },
-	{ "axp221" },
-	{ "axp223" },
-	{ "axp313a" },
-	{ "axp717" },
-	{ "axp803" },
-	{ "axp806" },
-	{ "axp15060" },
+	{ .name = "axp152",	.driver_data = AXP152_ID },
+	{ .name = "axp192",	.driver_data = AXP192_ID },
+	{ .name = "axp202",	.driver_data = AXP202_ID },
+	{ .name = "axp209",	.driver_data = AXP209_ID },
+	{ .name = "axp221",	.driver_data = AXP221_ID },
+	{ .name = "axp223",	.driver_data = AXP223_ID },
+	{ .name = "axp313a",	.driver_data = AXP313A_ID },
+	{ .name = "axp323",	.driver_data = AXP323_ID },
+	{ .name = "axp717",	.driver_data = AXP717_ID },
+	{ .name = "axp803",	.driver_data = AXP803_ID },
+	{ .name = "axp806",	.driver_data = AXP806_ID },
+	{ .name = "axp15060",	.driver_data = AXP15060_ID },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, axp20x_i2c_id);
diff --git a/drivers/mfd/axp20x-rsb.c b/drivers/mfd/axp20x-rsb.c
index 059656f2a1bd..8fdc870c1fe4 100644
--- a/drivers/mfd/axp20x-rsb.c
+++ b/drivers/mfd/axp20x-rsb.c
@@ -35,6 +35,7 @@ static int axp20x_rsb_probe(struct sunxi_rsb_device *rdev)
 	axp20x->irq = rdev->irq;
 	dev_set_drvdata(&rdev->dev, axp20x);
 
+	axp20x->variant = (kernel_ulong_t)device_get_match_data(axp20x->dev);
 	ret = axp20x_match_device(axp20x);
 	if (ret)
 		return ret;
diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index 4d770e718716..de6946d4bb13 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -1267,7 +1267,6 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
 	const struct mfd_cell *cells_no_irq = NULL;
 	int nr_cells_no_irq = 0;
 
-	axp20x->variant = (long)device_get_match_data(dev);
 	switch (axp20x->variant) {
 	case AXP152_ID:
 		axp20x->nr_cells = ARRAY_SIZE(axp152_cells);
diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
index b352661d99a1..1badb4868d17 100644
--- a/include/linux/mfd/axp20x.h
+++ b/include/linux/mfd/axp20x.h
@@ -997,8 +997,7 @@ static inline int axp20x_read_variable_width(struct regmap *regmap,
 /**
  * axp20x_match_device(): Setup axp20x variant related fields
  *
- * @axp20x: axp20x device to setup (.dev field must be set)
- * @dev: device associated with this axp20x device
+ * @axp20x: axp20x device to setup (.dev and variant fields must be set)
  *
  * This lets the axp20x core configure the mfd cells and register maps
  * for later use.

-- 
2.53.0

[PATCH v7 3/5] dt-bindings: mfd: x-powers,axp152: Document AXP318W

[Jerome Brunet]

From: Andre Przywara <andre.przywara@arm.com>

The X-Powers AXP318W is a PMIC used on some newer Allwinner devices.
Among a large number of both DCDC and LDO regulators it features the usual
ADC/IRQ/power key parts.
Like other recent PMICs, it lacks the DC/DC converter PWM frequency control
register, that rate is fixed here (1.5MHz on DCDC1, 3 MHz on the others).

Add the new compatible string, and add that to the list of PMICs without
the PWM frequency property.
Also add more input supply properties, for the split DCDC and ALDO
supplies.
The PMIC features *two* switched outputs, hanging of DCDC1, and the
manual calls them swout1 and swout2, so follow suit here and add those
names to the pattern for matching the node names.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Acked-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 .../devicetree/bindings/mfd/x-powers,axp152.yaml   | 28 +++++++++++++++++++++-
 1 file changed, 27 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml b/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
index 45f015d63df1..38556c32417b 100644
--- a/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
+++ b/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
@@ -83,6 +83,7 @@ allOf:
           contains:
             enum:
               - x-powers,axp313a
+              - x-powers,axp318w
               - x-powers,axp323
               - x-powers,axp15060
               - x-powers,axp717
@@ -102,6 +103,7 @@ properties:
           - x-powers,axp221
           - x-powers,axp223
           - x-powers,axp313a
+          - x-powers,axp318w
           - x-powers,axp323
           - x-powers,axp717
           - x-powers,axp803
@@ -156,10 +158,18 @@ properties:
     description: >
       DCDC1 power supply node, if present.
 
+  vin19-supply:
+    description: >
+      Combined DCDC1/DCDC9 power supply node, if present.
+
   vin2-supply:
     description: >
       DCDC2 power supply node, if present.
 
+  vin23-supply:
+    description: >
+      Combined DCDC2/DCDC3 power supply node, if present.
+
   vin3-supply:
     description: >
       DCDC3 power supply node, if present.
@@ -168,6 +178,10 @@ properties:
     description: >
       DCDC4 power supply node, if present.
 
+  vin45-supply:
+    description: >
+      Combined DCDC4/DCDC5 power supply node, if present.
+
   vin5-supply:
     description: >
       DCDC5 power supply node, if present.
@@ -176,6 +190,10 @@ properties:
     description: >
       DCDC6 power supply node, if present.
 
+  vin678-supply:
+    description: >
+      Combined DCDC6/DCDC7/DCDC8 power supply node, if present.
+
   vin7-supply:
     description: >
       DCDC7 power supply node, if present.
@@ -220,6 +238,14 @@ properties:
     description: >
       ALDO* power supply node, if present.
 
+  aldo156in-supply:
+    description: >
+      ALDO* power supply node, if present.
+
+  aldo234in-supply:
+    description: >
+      ALDO* power supply node, if present.
+
   bldoin-supply:
     description: >
       BLDO* power supply node, if present.
@@ -277,7 +303,7 @@ properties:
           Defines the work frequency of DC-DC in kHz.
 
     patternProperties:
-      "^(([a-f])?ldo[0-9]|dcdc[0-7a-e]|ldo(_|-)io(0|1)|(dc1)?sw|rtc(_|-)ldo|cpusldo|drivevbus|dc5ldo|boost)$":
+      "^(([a-f])?ldo[0-9]|dcdc[0-9a-e]|ldo(_|-)io(0|1)|(dc1)?sw|swout[1-2]|rtc(_|-)ldo|cpusldo|drivevbus|dc5ldo|boost)$":
         $ref: /schemas/regulator/regulator.yaml#
         type: object
         unevaluatedProperties: false

-- 
2.53.0

[PATCH v7 4/5] mfd: axp20x: Add support for AXP318W PMIC

[Jerome Brunet]

From: Andre Przywara <andre.przywara@arm.com>

The AXP318W is a PMIC chip produced by X-Powers, it can be connected to
an I2C bus.

It has a large number of regulators: 9(!) DCDC buck converters, and 28
LDOs, also some ADCs, interrupts, and a power key.

Describe the regmap and the MFD bits, along with the registers exposed
via I2C only. This covers the regulators and interrupts for now.
Advertise the device using the new compatible string.

We use just "318" for the internal identifiers, for easier typing and
less churn, but use "318W" for anything externally visible. If something
else other than the "AXP318W" shows up, that's an easy change then.

Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Co-developed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 drivers/mfd/axp20x-i2c.c   |   2 +
 drivers/mfd/axp20x.c       |  88 +++++++++++++++++++++++++++
 include/linux/mfd/axp20x.h | 145 +++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 235 insertions(+)

diff --git a/drivers/mfd/axp20x-i2c.c b/drivers/mfd/axp20x-i2c.c
index a76bec5604c4..64c212b76e5e 100644
--- a/drivers/mfd/axp20x-i2c.c
+++ b/drivers/mfd/axp20x-i2c.c
@@ -66,6 +66,7 @@ static const struct of_device_id axp20x_i2c_of_match[] = {
 	{ .compatible = "x-powers,axp221", .data = (void *)AXP221_ID },
 	{ .compatible = "x-powers,axp223", .data = (void *)AXP223_ID },
 	{ .compatible = "x-powers,axp313a", .data = (void *)AXP313A_ID },
+	{ .compatible = "x-powers,axp318w", .data = (void *)AXP318_ID },
 	{ .compatible = "x-powers,axp323", .data = (void *)AXP323_ID },
 	{ .compatible = "x-powers,axp717", .data = (void *)AXP717_ID },
 	{ .compatible = "x-powers,axp803", .data = (void *)AXP803_ID },
@@ -84,6 +85,7 @@ static const struct i2c_device_id axp20x_i2c_id[] = {
 	{ .name = "axp221",	.driver_data = AXP221_ID },
 	{ .name = "axp223",	.driver_data = AXP223_ID },
 	{ .name = "axp313a",	.driver_data = AXP313A_ID },
+	{ .name = "axp318w",	.driver_data = AXP318_ID },
 	{ .name = "axp323",	.driver_data = AXP323_ID },
 	{ .name = "axp717",	.driver_data = AXP717_ID },
 	{ .name = "axp803",	.driver_data = AXP803_ID },
diff --git a/drivers/mfd/axp20x.c b/drivers/mfd/axp20x.c
index de6946d4bb13..67ab529ebd2c 100644
--- a/drivers/mfd/axp20x.c
+++ b/drivers/mfd/axp20x.c
@@ -42,6 +42,7 @@ static const char * const axp20x_model_names[] = {
 	[AXP223_ID] = "AXP223",
 	[AXP288_ID] = "AXP288",
 	[AXP313A_ID] = "AXP313a",
+	[AXP318_ID] = "AXP318W",
 	[AXP323_ID] = "AXP323",
 	[AXP717_ID] = "AXP717",
 	[AXP803_ID] = "AXP803",
@@ -218,6 +219,38 @@ static const struct regmap_access_table axp313a_volatile_table = {
 	.n_yes_ranges = ARRAY_SIZE(axp313a_volatile_ranges),
 };
 
+static const struct regmap_range axp318_writeable_ranges[] = {
+	regmap_reg_range(AXP20X_DATACACHE(0), AXP20X_DATACACHE(3)),
+	regmap_reg_range(AXP318_DCDC_OUTPUT_CONTROL1, AXP318_DCDC_MODE_CTRL1),
+	regmap_reg_range(AXP318_DCDC_MODE_CTRL3, AXP318_DCDC_MODE_CTRL3),
+	regmap_reg_range(AXP318_LDO_OUTPUT_CONTROL1, AXP318_IRQ_EN4),
+	regmap_reg_range(AXP318_IRQ_STATE1, AXP318_IRQ_STATE4),
+	regmap_reg_range(AXP318_SHUTDOWN_SRC_CTRL1, AXP318_POK_CTRL),
+	regmap_reg_range(AXP318_WAKEUP_PWROK_PIN_CFG, AXP318_WAKEUP_PWROK_PIN_CFG),
+	regmap_reg_range(AXP318_TS_PIN_CFG, AXP318_TS_PIN_CFG),
+	regmap_reg_range(AXP318_TEMP_ADC_H_EN, AXP318_TEMP_ADC_H_EN),
+	regmap_reg_range(AXP318_DIE_TEMP_ADC_H_EN, AXP318_DIE_TEMP_ADC_H_EN),
+	regmap_reg_range(AXP318_GPADC_H_EN, AXP318_GPADC_H_EN),
+	regmap_reg_range(AXP318_GPIO_CTRL, AXP318_WDOG_CTRL),
+};
+
+static const struct regmap_range axp318_volatile_ranges[] = {
+	regmap_reg_range(AXP318_IRQ_STATE1, AXP318_IRQ_STATE4),
+	regmap_reg_range(AXP318_POWER_REASON, AXP318_SHUTDOWN_SOURCE),
+	regmap_reg_range(AXP318_TEMP_ADC_H_EN, AXP318_GPADC_L),
+	regmap_reg_range(AXP318_GPIO_INPUT, AXP318_GPIO_INPUT),
+};
+
+static const struct regmap_access_table axp318_writeable_table = {
+	.yes_ranges = axp318_writeable_ranges,
+	.n_yes_ranges = ARRAY_SIZE(axp318_writeable_ranges),
+};
+
+static const struct regmap_access_table axp318_volatile_table = {
+	.yes_ranges = axp318_volatile_ranges,
+	.n_yes_ranges = ARRAY_SIZE(axp318_volatile_ranges),
+};
+
 static const struct regmap_range axp717_writeable_ranges[] = {
 	regmap_reg_range(AXP717_PMU_FAULT, AXP717_MODULE_EN_CONTROL_1),
 	regmap_reg_range(AXP717_MIN_SYS_V_CONTROL, AXP717_BOOST_CONTROL),
@@ -447,6 +480,15 @@ static const struct regmap_config axp313a_regmap_config = {
 	.cache_type = REGCACHE_MAPLE,
 };
 
+static const struct regmap_config axp318_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.wr_table = &axp318_writeable_table,
+	.volatile_table = &axp318_volatile_table,
+	.max_register = AXP318_WDOG_CTRL,
+	.cache_type = REGCACHE_MAPLE,
+};
+
 static const struct regmap_config axp323_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
@@ -663,6 +705,28 @@ static const struct regmap_irq axp313a_regmap_irqs[] = {
 	INIT_REGMAP_IRQ(AXP313A, DIE_TEMP_HIGH,		0, 0),
 };
 
+static const struct regmap_irq axp318_regmap_irqs[] = {
+	INIT_REGMAP_IRQ(AXP318, DCDC8_V_LOW,		0, 7),
+	INIT_REGMAP_IRQ(AXP318, DCDC7_V_LOW,		0, 6),
+	INIT_REGMAP_IRQ(AXP318, DCDC6_V_LOW,		0, 5),
+	INIT_REGMAP_IRQ(AXP318, DCDC5_V_LOW,		0, 4),
+	INIT_REGMAP_IRQ(AXP318, DCDC4_V_LOW,		0, 3),
+	INIT_REGMAP_IRQ(AXP318, DCDC3_V_LOW,		0, 2),
+	INIT_REGMAP_IRQ(AXP318, DCDC2_V_LOW,		0, 1),
+	INIT_REGMAP_IRQ(AXP318, DCDC1_V_LOW,		0, 0),
+	INIT_REGMAP_IRQ(AXP318, PEK_RIS_EDGE,		1, 6),
+	INIT_REGMAP_IRQ(AXP318, PEK_FAL_EDGE,		1, 5),
+	INIT_REGMAP_IRQ(AXP318, PEK_SHORT,		1, 4),
+	INIT_REGMAP_IRQ(AXP318, PEK_LONG,		1, 3),
+	INIT_REGMAP_IRQ(AXP318, DIE_TEMP_HIGH_LV2,	1, 2),
+	INIT_REGMAP_IRQ(AXP318, DIE_TEMP_HIGH_LV1,	1, 1),
+	INIT_REGMAP_IRQ(AXP318, DCDC9_V_LOW,		1, 0),
+	INIT_REGMAP_IRQ(AXP318, GPIO3_INPUT,		2, 6),
+	INIT_REGMAP_IRQ(AXP318, GPIO2_INPUT,		2, 5),
+	INIT_REGMAP_IRQ(AXP318, GPIO1_INPUT,		2, 4),
+	INIT_REGMAP_IRQ(AXP318, WDOG_EXPIRE,		3, 0),
+};
+
 static const struct regmap_irq axp717_regmap_irqs[] = {
 	INIT_REGMAP_IRQ(AXP717, SOC_DROP_LVL2,		0, 7),
 	INIT_REGMAP_IRQ(AXP717, SOC_DROP_LVL1,		0, 6),
@@ -884,6 +948,17 @@ static const struct regmap_irq_chip axp313a_regmap_irq_chip = {
 	.num_regs		= 1,
 };
 
+static const struct regmap_irq_chip axp318_regmap_irq_chip = {
+	.name			= "axp318w_irq_chip",
+	.status_base		= AXP318_IRQ_STATE1,
+	.ack_base		= AXP318_IRQ_STATE1,
+	.unmask_base		= AXP318_IRQ_EN1,
+	.init_ack_masked	= true,
+	.irqs			= axp318_regmap_irqs,
+	.num_irqs		= ARRAY_SIZE(axp318_regmap_irqs),
+	.num_regs		= 4,
+};
+
 static const struct regmap_irq_chip axp717_regmap_irq_chip = {
 	.name			= "axp717_irq_chip",
 	.status_base		= AXP717_IRQ0_STATE,
@@ -1061,6 +1136,10 @@ static const struct mfd_cell axp313a_cells[] = {
 	MFD_CELL_RES("axp313a-pek", axp313a_pek_resources),
 };
 
+static const struct mfd_cell axp318_cells[] = {
+	MFD_CELL_NAME("axp20x-regulator"),
+};
+
 static const struct mfd_cell axp717_cells[] = {
 	MFD_CELL_NAME("axp20x-regulator"),
 	MFD_CELL_RES("axp20x-pek", axp717_pek_resources),
@@ -1248,6 +1327,9 @@ static int axp20x_power_off(struct sys_off_data *data)
 	case AXP313A_ID:
 		shutdown_reg = AXP313A_SHUTDOWN_CTRL;
 		break;
+	case AXP318_ID:
+		shutdown_reg = AXP318_SHUTDOWN_CTRL;
+		break;
 	default:
 		shutdown_reg = AXP20X_OFF_CTRL;
 		break;
@@ -1312,6 +1394,12 @@ int axp20x_match_device(struct axp20x_dev *axp20x)
 		axp20x->regmap_cfg = &axp313a_regmap_config;
 		axp20x->regmap_irq_chip = &axp313a_regmap_irq_chip;
 		break;
+	case AXP318_ID:
+		axp20x->nr_cells = ARRAY_SIZE(axp318_cells);
+		axp20x->cells = axp318_cells;
+		axp20x->regmap_cfg = &axp318_regmap_config;
+		axp20x->regmap_irq_chip = &axp318_regmap_irq_chip;
+		break;
 	case AXP323_ID:
 		axp20x->nr_cells = ARRAY_SIZE(axp313a_cells);
 		axp20x->cells = axp313a_cells;
diff --git a/include/linux/mfd/axp20x.h b/include/linux/mfd/axp20x.h
index 1badb4868d17..5c307f41a31f 100644
--- a/include/linux/mfd/axp20x.h
+++ b/include/linux/mfd/axp20x.h
@@ -19,6 +19,7 @@ enum axp20x_variants {
 	AXP223_ID,
 	AXP288_ID,
 	AXP313A_ID,
+	AXP318_ID,
 	AXP323_ID,
 	AXP717_ID,
 	AXP803_ID,
@@ -116,6 +117,84 @@ enum axp20x_variants {
 #define AXP313A_IRQ_STATE		0x21
 #define AXP323_DCDC_MODE_CTRL2		0x22
 
+#define AXP318_DCDC_OUTPUT_CONTROL1	0x10
+#define AXP318_DCDC_OUTPUT_CONTROL2	0x11
+#define AXP318_DCDC1_CONTROL		0x12
+#define AXP318_DCDC2_CONTROL		0x13
+#define AXP318_DCDC3_CONTROL		0x14
+#define AXP318_DCDC4_CONTROL		0x15
+#define AXP318_DCDC5_CONTROL		0x16
+#define AXP318_DCDC6_CONTROL		0x17
+#define AXP318_DCDC7_CONTROL		0x18
+#define AXP318_DCDC8_CONTROL		0x19
+#define AXP318_DCDC9_CONTROL		0x1a
+#define AXP318_DCDC_MODE_CTRL1		0x1b
+#define AXP318_DCDC_MODE_CTRL3		0x1d
+#define AXP318_LDO_OUTPUT_CONTROL1	0x20
+#define AXP318_LDO_OUTPUT_CONTROL2	0x21
+#define AXP318_LDO_OUTPUT_CONTROL3	0x22
+#define AXP318_LDO_OUTPUT_CONTROL4	0x23
+#define AXP318_ALDO1_CONTROL		0x24
+#define AXP318_ALDO2_CONTROL		0x25
+#define AXP318_ALDO3_CONTROL		0x26
+#define AXP318_ALDO4_CONTROL		0x27
+#define AXP318_ALDO5_CONTROL		0x28
+#define AXP318_ALDO6_CONTROL		0x29
+#define AXP318_BLDO1_CONTROL		0x2a
+#define AXP318_BLDO2_CONTROL		0x2b
+#define AXP318_BLDO3_CONTROL		0x2c
+#define AXP318_BLDO4_CONTROL		0x2d
+#define AXP318_BLDO5_CONTROL		0x2e
+#define AXP318_CLDO1_CONTROL		0x2f
+#define AXP318_CLDO2_CONTROL		0x30
+#define AXP318_CLDO3_CONTROL		0x31
+#define AXP318_CLDO4_CONTROL		0x32
+#define AXP318_CLDO5_CONTROL		0x33
+#define AXP318_DLDO1_CONTROL		0x34
+#define AXP318_DLDO2_CONTROL		0x35
+#define AXP318_DLDO3_CONTROL		0x36
+#define AXP318_DLDO4_CONTROL		0x37
+#define AXP318_DLDO5_CONTROL		0x38
+#define AXP318_DLDO6_CONTROL		0x39
+#define AXP318_ELDO1_CONTROL		0x3a
+#define AXP318_ELDO2_CONTROL		0x3b
+#define AXP318_ELDO3_CONTROL		0x3c
+#define AXP318_ELDO4_CONTROL		0x3d
+#define AXP318_ELDO5_CONTROL		0x3e
+#define AXP318_ELDO6_CONTROL		0x3f
+#define AXP318_IRQ_EN1			0x40
+#define AXP318_IRQ_EN2			0x41
+#define AXP318_IRQ_EN3			0x42
+#define AXP318_IRQ_EN4			0x43
+#define AXP318_IRQ_STATE1		0x48
+#define AXP318_IRQ_STATE2		0x49
+#define AXP318_IRQ_STATE3		0x4a
+#define AXP318_IRQ_STATE4		0x4b
+#define AXP318_POWER_REASON		0x50
+#define AXP318_SHUTDOWN_SOURCE		0x51
+#define AXP318_SHUTDOWN_SRC_CTRL1	0x52
+#define AXP318_SHUTDOWN_SRC_CTRL2	0x53
+#define AXP318_DISCHARGE_OVERTEMP_CTRL	0x54
+#define AXP318_SHUTDOWN_CTRL		0x55
+#define AXP318_WAKEUP_VOFF_CTRL		0x56
+#define AXP318_POK_CTRL			0x57
+#define AXP318_WAKEUP_PWROK_PIN_CFG	0x5d
+#define AXP318_TS_PIN_CFG		0x60
+#define AXP318_TEMP_ADC_H_EN		0x65
+#define AXP318_TEMP_ADC_L		0x66
+#define AXP318_DIE_TEMP_ADC_H_EN	0x67
+#define AXP318_DIE_TEMP_ADC_L		0x68
+#define AXP318_GPADC_H_EN		0x69
+#define AXP318_GPADC_L			0x6a
+#define AXP318_GPIO_CTRL		0x70
+#define AXP318_GPIO_INPUT		0x71
+#define AXP318_GPIO_OUTPUT		0x72
+#define AXP318_PWM_CTRL1		0x73
+#define AXP318_PWM_CTRL2		0x74
+#define AXP318_PWM_CTRL3		0x75
+#define AXP318_BACKUP_BATTERY_CTRL	0x76
+#define AXP318_WDOG_CTRL		0x77
+
 #define AXP717_ON_INDICATE		0x00
 #define AXP717_PMU_STATUS_2		0x01
 #define AXP717_BC_DETECT		0x05
@@ -498,6 +577,50 @@ enum {
 	AXP313A_REG_ID_MAX,
 };
 
+enum {
+	AXP318_DCDC1 = 0,
+	AXP318_DCDC2,
+	AXP318_DCDC3,
+	AXP318_DCDC4,
+	AXP318_DCDC5,
+	AXP318_DCDC6,
+	AXP318_DCDC7,
+	AXP318_DCDC8,
+	AXP318_DCDC9,
+	AXP318_ALDO1,
+	AXP318_ALDO2,
+	AXP318_ALDO3,
+	AXP318_ALDO4,
+	AXP318_ALDO5,
+	AXP318_ALDO6,
+	AXP318_BLDO1,
+	AXP318_BLDO2,
+	AXP318_BLDO3,
+	AXP318_BLDO4,
+	AXP318_BLDO5,
+	AXP318_CLDO1,
+	AXP318_CLDO2,
+	AXP318_CLDO3,
+	AXP318_CLDO4,
+	AXP318_CLDO5,
+	AXP318_DLDO1,
+	AXP318_DLDO2,
+	AXP318_DLDO3,
+	AXP318_DLDO4,
+	AXP318_DLDO5,
+	AXP318_DLDO6,
+	AXP318_ELDO1,
+	AXP318_ELDO2,
+	AXP318_ELDO3,
+	AXP318_ELDO4,
+	AXP318_ELDO5,
+	AXP318_ELDO6,
+	AXP318_SWOUT1,
+	AXP318_SWOUT2,
+	AXP318_RTC_LDO,
+	AXP318_REG_ID_MAX,
+};
+
 enum {
 	AXP717_DCDC1 = 0,
 	AXP717_DCDC2,
@@ -819,6 +942,28 @@ enum axp313a_irqs {
 	AXP313A_IRQ_PEK_RIS_EDGE,
 };
 
+enum axp318_irqs {
+	AXP318_IRQ_DCDC1_V_LOW,
+	AXP318_IRQ_DCDC2_V_LOW,
+	AXP318_IRQ_DCDC3_V_LOW,
+	AXP318_IRQ_DCDC4_V_LOW,
+	AXP318_IRQ_DCDC5_V_LOW,
+	AXP318_IRQ_DCDC6_V_LOW,
+	AXP318_IRQ_DCDC7_V_LOW,
+	AXP318_IRQ_DCDC8_V_LOW,
+	AXP318_IRQ_DCDC9_V_LOW,
+	AXP318_IRQ_DIE_TEMP_HIGH_LV1,
+	AXP318_IRQ_DIE_TEMP_HIGH_LV2,
+	AXP318_IRQ_PEK_LONG,
+	AXP318_IRQ_PEK_SHORT,
+	AXP318_IRQ_PEK_FAL_EDGE,
+	AXP318_IRQ_PEK_RIS_EDGE,
+	AXP318_IRQ_GPIO1_INPUT = 20,
+	AXP318_IRQ_GPIO2_INPUT,
+	AXP318_IRQ_GPIO3_INPUT,
+	AXP318_IRQ_WDOG_EXPIRE = 24,
+};
+
 enum axp717_irqs {
 	AXP717_IRQ_VBUS_FAULT,
 	AXP717_IRQ_VBUS_OVER_V,

-- 
2.53.0

[PATCH v7 5/5] regulator: axp20x: add support for the AXP318W

[Jerome Brunet]

From: Andre Przywara <andre.przywara@arm.com>

The X-Powers AXP318W is a typical PMIC from X-Powers, featuring nine
DC/DC converters and 28 LDOs, on the regulator side.

Describe the chip's voltage settings and switch registers, how the
voltages are encoded, and connect this to the MFD device via its
regulator ID.
We use just "318" for the internal identifiers, for easier typing and
less churn. If something else other than the "AXP318W" shows up, that's
an easy change, externally visible strings carry the additional letter
already.

Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Co-developed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
---
 drivers/regulator/axp20x-regulator.c | 319 ++++++++++++++++++++++++++++++++++-
 1 file changed, 310 insertions(+), 9 deletions(-)

diff --git a/drivers/regulator/axp20x-regulator.c b/drivers/regulator/axp20x-regulator.c
index da891415efc0..732541ee619e 100644
--- a/drivers/regulator/axp20x-regulator.c
+++ b/drivers/regulator/axp20x-regulator.c
@@ -138,6 +138,29 @@
 #define AXP313A_DCDC_V_OUT_MASK		GENMASK(6, 0)
 #define AXP313A_LDO_V_OUT_MASK		GENMASK(4, 0)
 
+#define AXP318_DCDC1_PFM_PWM_CTRL	BIT(7)
+#define AXP318_DCDC23_POLYPHASE_CTRL	BIT(6)
+#define AXP318_DCDC45_POLYPHASE_CTRL	BIT(7)
+#define AXP318_DCDC1_V_OUT_MASK		GENMASK(4, 0)
+#define AXP318_DCDC2_V_OUT_MASK		GENMASK(6, 0)
+#define AXP318_LDO_V_OUT_MASK		GENMASK(4, 0)
+#define AXP318_ELDO_V_OUT_MASK		GENMASK(5, 0)
+#define AXP318_THRESHOLD_VOLTAGE	1540000
+/*
+ * FIXME:
+ * Some LDOs of the AXP318 may be fed by different supplies and
+ * the documentation repeatedly warns that output voltage must
+ * be less than the supply, which is the case for any LDO really.
+ *
+ * The best way to let the framework handle this is to set the
+ * min_dropout_uV field. However the AXP318 documentation
+ * does not provide any information about this.
+ *
+ * Realistically, it can't be less than 1uV so use this
+ * for all LDOs until we know more.
+ */
+#define AXP318_LDO_MIN_DROPOUT		1 /* uV */
+
 #define AXP717_DCDC1_NUM_VOLTAGES	88
 #define AXP717_DCDC2_NUM_VOLTAGES	107
 #define AXP717_DCDC3_NUM_VOLTAGES	103
@@ -371,8 +394,8 @@
 		.ops		= &axp20x_ops,					\
 	}
 
-#define AXP_DESC(_family, _id, _match, _supply, _min, _max, _step, _vreg,	\
-		 _vmask, _ereg, _emask)						\
+#define AXP_DESC_EXT(_family, _id, _match, _supply, _min, _max, _step, _vreg,	\
+		     _vmask, _ereg, _emask, _ops, _bpreg, _bpmask, _dropout)	\
 	[_family##_##_id] = {							\
 		.name		= (_match),					\
 		.supply_name	= (_supply),					\
@@ -384,13 +407,32 @@
 		.owner		= THIS_MODULE,					\
 		.min_uV		= (_min) * 1000,				\
 		.uV_step	= (_step) * 1000,				\
+		.min_dropout_uV = (_dropout),					\
 		.vsel_reg	= (_vreg),					\
 		.vsel_mask	= (_vmask),					\
 		.enable_reg	= (_ereg),					\
 		.enable_mask	= (_emask),					\
-		.ops		= &axp20x_ops,					\
+		.bypass_reg	= (_bpreg),					\
+		.bypass_mask	= (_bpmask),					\
+		.ops		= (_ops),					\
 	}
 
+#define AXP_DESC(_family, _id, _match, _supply, _min, _max, _step, _vreg,	\
+		 _vmask, _ereg, _emask)						\
+	AXP_DESC_EXT(_family, _id, _match, _supply, _min, _max, _step, _vreg,	\
+		     _vmask, _ereg, _emask, &axp20x_ops, 0, 0, 0)
+
+#define AXP_DESC_DO(_family, _id, _match, _supply, _min, _max, _step, _vreg,	\
+		    _vmask, _ereg, _emask, _dropout)				\
+	AXP_DESC_EXT(_family, _id, _match, _supply, _min, _max, _step, _vreg,	\
+		     _vmask, _ereg, _emask, &axp20x_ops, 0, 0, _dropout)
+
+#define AXP_DESC_BYPASS(_family, _id, _match, _supply, _min, _max, _step, _vreg,\
+			_vmask, _ereg, _emask, _bpreg, _bpmask, _dropout)	\
+	AXP_DESC_EXT(_family, _id, _match, _supply, _min, _max, _step, _vreg,	\
+		     _vmask, _ereg, _emask, &axp20x_bypass_ops, _bpreg,		\
+		     _bpmask, _dropout)
+
 #define AXP_DESC_SW(_family, _id, _match, _supply, _ereg, _emask)		\
 	[_family##_##_id] = {							\
 		.name		= (_match),					\
@@ -419,8 +461,9 @@
 		.ops		= &axp20x_ops_fixed				\
 	}
 
-#define AXP_DESC_RANGES_DELAY(_family, _id, _match, _supply, _ranges, _n_voltages,	\
-			_vreg, _vmask, _ereg, _emask, _ramp_delay)	\
+#define AXP_DESC_RANGES_DELAY_OPS(_family, _id, _match, _supply, _ranges,	\
+				  _n_voltages, _vreg, _vmask, _ereg, _emask,	\
+				  _ramp_delay, _ops)				\
 	[_family##_##_id] = {							\
 		.name		= (_match),					\
 		.supply_name	= (_supply),					\
@@ -436,10 +479,23 @@
 		.enable_mask	= (_emask),					\
 		.linear_ranges	= (_ranges),					\
 		.n_linear_ranges = ARRAY_SIZE(_ranges),				\
-		.ramp_delay = (_ramp_delay),					\
-		.ops		= &axp20x_ops_range,				\
+		.ramp_delay	= (_ramp_delay),				\
+		.ops		= (_ops),					\
 	}
 
+#define AXP_DESC_RANGES_THRESHOLD(_family, _id, _match, _supply, _ranges,	\
+				  _n_voltages, _vreg, _vmask, _ereg, _emask)	\
+	AXP_DESC_RANGES_DELAY_OPS(_family, _id, _match, _supply, _ranges,	\
+				  _n_voltages, _vreg, _vmask, _ereg, _emask,	\
+				  0, &axp318_threshold_ops_range)
+
+#define AXP_DESC_RANGES_DELAY(_family, _id, _match, _supply, _ranges,		\
+			      _n_voltages, _vreg, _vmask, _ereg, _emask,	\
+			      _ramp_delay)					\
+	AXP_DESC_RANGES_DELAY_OPS(_family, _id, _match, _supply, _ranges,	\
+				  _n_voltages, _vreg, _vmask, _ereg, _emask,	\
+				  _ramp_delay, &axp20x_ops_range)
+
 #define AXP_DESC_RANGES(_family, _id, _match, _supply, _ranges, _n_voltages,	\
 			_vreg, _vmask, _ereg, _emask)				\
 	AXP_DESC_RANGES_DELAY(_family, _id, _match, _supply, _ranges,		\
@@ -567,6 +623,50 @@ static int axp20x_regulator_enable_regmap(struct regulator_dev *rdev)
 	return regulator_enable_regmap(rdev);
 };
 
+static int axp318_threshold_check(struct regulator_dev *rdev,
+				  unsigned int sel)
+{
+	int old_sel, old_uV, new_uV, enabled;
+
+	/* Only applicable if the regulator is enabled */
+	enabled = rdev->desc->ops->is_enabled(rdev);
+	if (enabled <= 0)
+		return enabled;
+
+	old_sel = rdev->desc->ops->get_voltage_sel(rdev);
+	if (old_sel < 0)
+		return old_sel;
+
+	old_uV = rdev->desc->ops->list_voltage(rdev, old_sel);
+	if (old_uV < 0)
+		return old_uV;
+
+	new_uV = rdev->desc->ops->list_voltage(rdev, sel);
+	if (new_uV < 0)
+		return new_uV;
+
+	/* Crossing the threshold ? */
+	if ((old_uV <= AXP318_THRESHOLD_VOLTAGE &&
+	     new_uV > AXP318_THRESHOLD_VOLTAGE) ||
+	    (new_uV <= AXP318_THRESHOLD_VOLTAGE &&
+	     old_uV > AXP318_THRESHOLD_VOLTAGE))
+		return -EBUSY;
+
+	return 0;
+}
+
+static int axp318_threshold_set_voltage_sel(struct regulator_dev *rdev,
+					    unsigned int sel)
+{
+	int ret;
+
+	ret = axp318_threshold_check(rdev, sel);
+	if (ret < 0)
+		return ret;
+
+	return regulator_set_voltage_sel_regmap(rdev, sel);
+}
+
 static const struct regulator_ops axp20x_ops_fixed = {
 	.list_voltage		= regulator_list_voltage_linear,
 };
@@ -580,6 +680,15 @@ static const struct regulator_ops axp20x_ops_range = {
 	.is_enabled		= regulator_is_enabled_regmap,
 };
 
+static const struct regulator_ops axp318_threshold_ops_range = {
+	.set_voltage_sel	= axp318_threshold_set_voltage_sel,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.list_voltage		= regulator_list_voltage_linear_range,
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+};
+
 static const struct regulator_ops axp20x_ops = {
 	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
 	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
@@ -590,6 +699,18 @@ static const struct regulator_ops axp20x_ops = {
 	.set_ramp_delay		= axp20x_set_ramp_delay,
 };
 
+static const struct regulator_ops axp20x_bypass_ops = {
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.list_voltage		= regulator_list_voltage_linear,
+	.enable			= axp20x_regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.set_ramp_delay		= axp20x_set_ramp_delay,
+	.get_bypass		= regulator_get_bypass_regmap,
+	.set_bypass		= regulator_set_bypass_regmap,
+};
+
 static const struct regulator_ops axp20x_ops_sw = {
 	.enable			= regulator_enable_regmap,
 	.disable		= regulator_disable_regmap,
@@ -765,6 +886,158 @@ static const struct regulator_desc axp313a_regulators[] = {
 	AXP_DESC_FIXED(AXP313A, RTC_LDO, "rtc-ldo", "vin1", 1800),
 };
 
+static const struct linear_range axp318_dcdc2_ranges[] = {
+	REGULATOR_LINEAR_RANGE(500000,   0, 70, 10000),
+	REGULATOR_LINEAR_RANGE(1220000, 71, 87, 20000),
+};
+
+static const struct linear_range axp318_dcdc6_ranges[] = {
+	REGULATOR_LINEAR_RANGE(500000,    0,  70,  10000),
+	REGULATOR_LINEAR_RANGE(1220000,  71,  87,  20000),
+	REGULATOR_LINEAR_RANGE(1800000,  88, 118,  20000),
+	REGULATOR_LINEAR_RANGE(2440000, 119, 127,  40000),
+};
+
+static const struct linear_range axp318_dcdc7_ranges[] = {
+	REGULATOR_LINEAR_RANGE(500000,   0,  70, 10000),
+	REGULATOR_LINEAR_RANGE(1220000, 71, 102, 20000),
+};
+
+static const struct linear_range axp318_dcdc8_ranges[] = {
+	REGULATOR_LINEAR_RANGE(500000,    0,  70,  10000),
+	REGULATOR_LINEAR_RANGE(1220000,  71, 102,  20000),
+	REGULATOR_LINEAR_RANGE(1900000, 103, 118, 100000),
+};
+
+static const struct regulator_desc axp318_regulators[] = {
+	AXP_DESC(AXP318, DCDC1, "dcdc1", "vin19", 1000, 3400, 100,
+		 AXP318_DCDC1_CONTROL, AXP318_DCDC1_V_OUT_MASK,
+		 AXP318_DCDC_OUTPUT_CONTROL1, BIT(0)),
+	AXP_DESC_RANGES(AXP318, DCDC2, "dcdc2", "vin23",
+			axp318_dcdc2_ranges, 88,
+			AXP318_DCDC2_CONTROL, AXP318_DCDC2_V_OUT_MASK,
+			AXP318_DCDC_OUTPUT_CONTROL1, BIT(1)),
+	AXP_DESC_RANGES(AXP318, DCDC3, "dcdc3", "vin23",
+			axp318_dcdc2_ranges, 88,
+			AXP318_DCDC3_CONTROL, AXP318_DCDC2_V_OUT_MASK,
+			AXP318_DCDC_OUTPUT_CONTROL1, BIT(2)),
+	AXP_DESC_RANGES(AXP318, DCDC4, "dcdc4", "vin45",
+			axp318_dcdc2_ranges, 88,
+			AXP318_DCDC4_CONTROL, AXP318_DCDC2_V_OUT_MASK,
+			AXP318_DCDC_OUTPUT_CONTROL1, BIT(3)),
+	AXP_DESC_RANGES(AXP318, DCDC5, "dcdc5", "vin45",
+			axp318_dcdc2_ranges, 88,
+			AXP318_DCDC5_CONTROL, AXP318_DCDC2_V_OUT_MASK,
+			AXP318_DCDC_OUTPUT_CONTROL1, BIT(4)),
+	AXP_DESC_RANGES_THRESHOLD(AXP318, DCDC6, "dcdc6", "vin678",
+			axp318_dcdc6_ranges, 128,
+			AXP318_DCDC6_CONTROL, AXP318_DCDC2_V_OUT_MASK,
+			AXP318_DCDC_OUTPUT_CONTROL1, BIT(5)),
+	AXP_DESC_RANGES_THRESHOLD(AXP318, DCDC7, "dcdc7", "vin678",
+			axp318_dcdc7_ranges, 103,
+			AXP318_DCDC7_CONTROL, AXP318_DCDC2_V_OUT_MASK,
+			AXP318_DCDC_OUTPUT_CONTROL1, BIT(6)),
+	AXP_DESC_RANGES_THRESHOLD(AXP318, DCDC8, "dcdc8", "vin678",
+			axp318_dcdc8_ranges, 119,
+			AXP318_DCDC8_CONTROL, AXP318_DCDC2_V_OUT_MASK,
+			AXP318_DCDC_OUTPUT_CONTROL1, BIT(7)),
+	AXP_DESC_RANGES_THRESHOLD(AXP318, DCDC9, "dcdc9", "vin19",
+			axp318_dcdc8_ranges, 119,
+			AXP318_DCDC9_CONTROL, AXP318_DCDC2_V_OUT_MASK,
+			AXP318_DCDC_OUTPUT_CONTROL2, BIT(0)),
+	AXP_DESC_SW(AXP318, SWOUT1, "swout1", NULL,
+		    AXP318_DCDC_OUTPUT_CONTROL2, BIT(3)),
+	AXP_DESC_SW(AXP318, SWOUT2, "swout2", NULL,
+		    AXP318_DCDC_OUTPUT_CONTROL2, BIT(4)),
+	AXP_DESC_DO(AXP318, ALDO1, "aldo1", "aldo156in", 500, 3400, 100,
+		    AXP318_ALDO1_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL1, BIT(0), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, ALDO2, "aldo2", "aldo234in", 500, 3400, 100,
+		    AXP318_ALDO2_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL1, BIT(1), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, ALDO3, "aldo3", "aldo234in", 500, 3400, 100,
+		    AXP318_ALDO3_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL1, BIT(2), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, ALDO4, "aldo4", "aldo234in", 500, 3400, 100,
+		    AXP318_ALDO4_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL1, BIT(3), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, ALDO5, "aldo5", "aldo156in", 500, 3400, 100,
+		    AXP318_ALDO5_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL1, BIT(4), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, ALDO6, "aldo6", "aldo156in", 500, 3400, 100,
+		    AXP318_ALDO6_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL1, BIT(5), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, BLDO1, "bldo1", "bldoin", 500, 3400, 100,
+		    AXP318_BLDO1_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL1, BIT(6), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, BLDO2, "bldo2", "bldoin", 500, 3400, 100,
+		    AXP318_BLDO2_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL1, BIT(7), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, BLDO3, "bldo3", "bldoin", 500, 3400, 100,
+		    AXP318_BLDO3_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL2, BIT(0), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, BLDO4, "bldo4", "bldoin", 500, 3400, 100,
+		    AXP318_BLDO4_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL2, BIT(1), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, BLDO5, "bldo5", "bldoin", 500, 3400, 100,
+		    AXP318_BLDO5_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL2, BIT(2), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, CLDO1, "cldo1", "cldoin", 500, 3400, 100,
+		    AXP318_CLDO1_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL2, BIT(3), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, CLDO2, "cldo2", "cldoin", 500, 3400, 100,
+		    AXP318_CLDO2_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL2, BIT(4), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, CLDO3, "cldo3", "cldoin", 500, 3400, 100,
+		    AXP318_CLDO3_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL2, BIT(5), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, CLDO4, "cldo4", "cldoin", 500, 3400, 100,
+		    AXP318_CLDO4_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL2, BIT(6), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, CLDO5, "cldo5", "cldoin", 500, 3400, 100,
+		    AXP318_CLDO5_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL2, BIT(7), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, DLDO1, "dldo1", "dldoin", 500, 3400, 100,
+		    AXP318_DLDO1_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL3, BIT(0), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, DLDO2, "dldo2", "dldoin", 500, 3400, 100,
+		    AXP318_DLDO2_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL3, BIT(1), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, DLDO3, "dldo3", "dldoin", 500, 3400, 100,
+		    AXP318_DLDO3_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL3, BIT(2), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, DLDO4, "dldo4", "dldoin", 500, 3400, 100,
+		    AXP318_DLDO4_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL3, BIT(3), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, DLDO5, "dldo5", "dldoin", 500, 3400, 100,
+		    AXP318_DLDO5_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL3, BIT(4), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, DLDO6, "dldo6", "dldoin", 500, 3400, 100,
+		    AXP318_DLDO6_CONTROL, AXP318_LDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL3, BIT(5), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, ELDO1, "eldo1", "eldoin", 500, 1500, 25,
+		    AXP318_ELDO1_CONTROL, AXP318_ELDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL3, BIT(6), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, ELDO2, "eldo2", "eldoin", 500, 1500, 25,
+		    AXP318_ELDO2_CONTROL, AXP318_ELDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL3, BIT(7), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, ELDO3, "eldo3", "eldoin", 500, 1500, 25,
+		    AXP318_ELDO3_CONTROL, AXP318_ELDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL4, BIT(0), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_BYPASS(AXP318, ELDO4, "eldo4", "eldoin", 500, 1500, 25,
+			AXP318_ELDO4_CONTROL, AXP318_ELDO_V_OUT_MASK,
+			AXP318_LDO_OUTPUT_CONTROL4, BIT(1),
+			AXP318_ELDO4_CONTROL, BIT(6), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_BYPASS(AXP318, ELDO5, "eldo5", "eldoin", 500, 1500, 25,
+			AXP318_ELDO5_CONTROL, AXP318_ELDO_V_OUT_MASK,
+			AXP318_LDO_OUTPUT_CONTROL4, BIT(2),
+			AXP318_ELDO5_CONTROL, BIT(6), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_DO(AXP318, ELDO6, "eldo6", "eldoin", 500, 1500, 25,
+		    AXP318_ELDO6_CONTROL, AXP318_ELDO_V_OUT_MASK,
+		    AXP318_LDO_OUTPUT_CONTROL4, BIT(3), AXP318_LDO_MIN_DROPOUT),
+	AXP_DESC_FIXED(AXP318, RTC_LDO, "rtc-ldo", "ips", 1800),
+};
+
 static const struct linear_range axp717_dcdc1_ranges[] = {
 	REGULATOR_LINEAR_RANGE(500000,   0, 70, 10000),
 	REGULATOR_LINEAR_RANGE(1220000, 71, 87, 20000),
@@ -1347,6 +1620,7 @@ static int axp20x_set_dcdc_freq(struct platform_device *pdev, u32 dcdcfreq)
 		step = 150;
 		break;
 	case AXP313A_ID:
+	case AXP318_ID:
 	case AXP323_ID:
 	case AXP717_ID:
 	case AXP15060_ID:
@@ -1430,6 +1704,15 @@ static int axp20x_set_dcdc_workmode(struct regulator_dev *rdev, int id, u32 work
 		workmode <<= ffs(mask) - 1;
 		break;
 
+	case AXP318_ID:
+		/* Only DCDC1 has PWM control on the AXP318 */
+		if (id != AXP318_DCDC1)
+			return -EINVAL;
+		reg = AXP318_DCDC1_CONTROL;
+		mask = AXP318_DCDC1_PFM_PWM_CTRL;
+		workmode <<= ffs(mask) - 1;
+		break;
+
 	case AXP806_ID:
 		/*
 		 * AXP806 DCDC regulator IDs have the same range as AXP22X.
@@ -1543,6 +1826,17 @@ static bool axp20x_is_polyphase_slave(struct axp20x_dev *axp20x, int id)
 		}
 		break;
 
+	case AXP318_ID:
+		regmap_read(axp20x->regmap, AXP318_DCDC_MODE_CTRL1, &reg);
+
+		switch (id) {
+		case AXP318_DCDC3:
+			return !!(reg & AXP318_DCDC23_POLYPHASE_CTRL);
+		case AXP318_DCDC5:
+			return !!(reg & AXP318_DCDC45_POLYPHASE_CTRL);
+		}
+		break;
+
 	default:
 		return false;
 	}
@@ -1585,6 +1879,10 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
 		regulators = axp313a_regulators;
 		nregulators = AXP313A_REG_ID_MAX;
 		break;
+	case AXP318_ID:
+		regulators = axp318_regulators;
+		nregulators = AXP318_REG_ID_MAX;
+		break;
 	case AXP717_ID:
 		regulators = axp717_regulators;
 		nregulators = AXP717_REG_ID_MAX;
@@ -1651,7 +1949,9 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
 		if ((regulators == axp22x_regulators && i == AXP22X_DC1SW) ||
 		    (regulators == axp803_regulators && i == AXP803_DC1SW) ||
 		    (regulators == axp809_regulators && i == AXP809_DC1SW) ||
-		    (regulators == axp15060_regulators && i == AXP15060_SW)) {
+		    (regulators == axp15060_regulators && i == AXP15060_SW) ||
+		    (regulators == axp318_regulators && i == AXP318_SWOUT1) ||
+		    (regulators == axp318_regulators && i == AXP318_SWOUT2)) {
 			new_desc = devm_kzalloc(&pdev->dev, sizeof(*desc),
 						GFP_KERNEL);
 			if (!new_desc)
@@ -1709,7 +2009,8 @@ static int axp20x_regulator_probe(struct platform_device *pdev)
 		 */
 		if ((regulators == axp22x_regulators && i == AXP22X_DCDC1) ||
 		    (regulators == axp809_regulators && i == AXP809_DCDC1) ||
-		    (regulators == axp15060_regulators && i == AXP15060_DCDC1))
+		    (regulators == axp15060_regulators && i == AXP15060_DCDC1) ||
+		    (regulators == axp318_regulators && i == AXP318_DCDC1))
 			of_property_read_string(rdev->dev.of_node,
 						"regulator-name",
 						&dcdc1_name);

-- 
2.53.0

Re: [PATCH v7 1/5] mfd: axp20x: Constify axp313 and axp717 cells

[sashiko-bot]

> mfd_cells array should generally be const and there does not seem to be
> anything against it for the axp313 and axp717.
> 
> Constify the mfd_cells array for the axp313 and axp717 to be consistent
> with the other supported chips
> 
> Acked-by: Chen-Yu Tsai <wens@kernel.org>
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Sashiko has reviewed this patch and found no issues. It looks great!

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260910-axp318-regulator-v7-0-de720ceb9bac@baylibre.com?part=1

Re: [PATCH v7 5/5] regulator: axp20x: add support for the AXP318W

[sashiko-bot]

> From: Andre Przywara <andre.przywara@arm.com>
> 
> The X-Powers AXP318W is a typical PMIC from X-Powers, featuring nine
> DC/DC converters and 28 LDOs, on the regulator side.
> 
> Describe the chip's voltage settings and switch registers, how the
> voltages are encoded, and connect this to the MFD device via its
> regulator ID.
> We use just "318" for the internal identifiers, for easier typing and
> less churn. If something else other than the "AXP318W" shows up, that's
> an easy change, externally visible strings carry the additional letter
> already.
> 
> Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
> Reviewed-by: Mark Brown <broonie@kernel.org>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Co-developed-by: Jerome Brunet <jbrunet@baylibre.com>
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Sashiko has reviewed this patch and found no issues. It looks great!

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260910-axp318-regulator-v7-0-de720ceb9bac@baylibre.com?part=5

Re: [PATCH v7 4/5] mfd: axp20x: Add support for AXP318W PMIC

[sashiko-bot]

> From: Andre Przywara <andre.przywara@arm.com>
> 
> The AXP318W is a PMIC chip produced by X-Powers, it can be connected to
> an I2C bus.
> 
> It has a large number of regulators: 9(!) DCDC buck converters, and 28
> LDOs, also some ADCs, interrupts, and a power key.
> 
> Describe the regmap and the MFD bits, along with the registers exposed
> via I2C only. This covers the regulators and interrupts for now.
> Advertise the device using the new compatible string.
> 
> We use just "318" for the internal identifiers, for easier typing and
> less churn, but use "318W" for anything externally visible. If something
> else other than the "AXP318W" shows up, that's an easy change then.
> 
> Reviewed-by: Chen-Yu Tsai <wens@kernel.org>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Co-developed-by: Jerome Brunet <jbrunet@baylibre.com>
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Sashiko has reviewed this patch and found no issues. It looks great!

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260910-axp318-regulator-v7-0-de720ceb9bac@baylibre.com?part=4

Re: [PATCH v7 2/5] mfd: axp20x-i2c: Fix i2c instantiation

[sashiko-bot]

> Apparently this device never really supported i2c instantiation via
> sysfs, because the driver does not even look at the i2c device data,
> which are not set. It would only probe if the device matched through DT.
> 
> Fix that for correctness, even-though it is probably useless.
> Add the missing AXP323 while at it.
> 
> Reported-by: Sashiko <sashiko-bot@kernel.org>
> Closes: https://lore.kernel.org/r/20260717090209.2A09B1F000E9@smtp.kernel.org
> Fixes: 41751b033aaa ("mfd: axp20x-i2c: Add i2c-ids to fix module auto-loading")
> Acked-by: Chen-Yu Tsai <wens@kernel.org>
> Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>

Sashiko has reviewed this patch and found no issues. It looks great!

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260910-axp318-regulator-v7-0-de720ceb9bac@baylibre.com?part=2

Re: [PATCH v7 3/5] dt-bindings: mfd: x-powers,axp152: Document AXP318W

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] The new `x-powers,axp318w` compatible string is omitted from the conditional block that makes the `interrupts` property optional for recent generation PMICs.
--

commit e4119d6ce87c67baf660bd6f040790fb69b77af3
Author: Andre Przywara <andre.przywara@arm.com>

dt-bindings: mfd: x-powers,axp152: Document AXP318W

This commit adds the compatible string x-powers,axp318w for the AXP318W PMIC
to the binding schema. It also adds new input supply properties and updates
the regex for matching switched output nodes.

> diff --git a/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml b/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
> index 45f015d63df16..38556c32417b3 100644
> --- a/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
> +++ b/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
> @@ -83,6 +83,7 @@ allOf:
>            contains:
>              enum:
>                - x-powers,axp313a
> +              - x-powers,axp318w
>                - x-powers,axp323
>                - x-powers,axp15060
>                - x-powers,axp717

[Severity: Medium]
Does the x-powers,axp318w compatible string also need to be added to the
earlier if-then block that governs the interrupts requirement?

Just above this hunk in Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml,
there is a block that makes interrupts mandatory for all PMICs except a select
few:

  - if:
      not:
        properties:
          compatible:
            contains:
              enum:
                - x-powers,axp15060
                - x-powers,axp305
                - x-powers,axp313a
                - x-powers,axp323

    then:
      required:
        - interrupts

By omitting x-powers,axp318w from this enum, the interrupts property is
mandatory for the new PMIC. Could this cause device trees with an unconnected
AXP318W interrupt line to falsely fail dt_binding_check validation, given that
similar recent generation PMICs operate fine without it?

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260910-axp318-regulator-v7-0-de720ceb9bac@baylibre.com?part=3

Re: [PATCH v7 3/5] dt-bindings: mfd: x-powers,axp152: Document AXP318W

[Jerome Brunet]

On jeu. 10 sept. 2026 at 09:42, sashiko-bot@kernel.org wrote:

> Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
> - [Medium] The new `x-powers,axp318w` compatible string is omitted from the conditional block that makes the `interrupts` property optional for recent generation PMICs.
> --
>
> commit e4119d6ce87c67baf660bd6f040790fb69b77af3
> Author: Andre Przywara <andre.przywara@arm.com>
>
> dt-bindings: mfd: x-powers,axp152: Document AXP318W
>
> This commit adds the compatible string x-powers,axp318w for the AXP318W PMIC
> to the binding schema. It also adds new input supply properties and updates
> the regex for matching switched output nodes.
>
>> diff --git a/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml b/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
>> index 45f015d63df16..38556c32417b3 100644
>> --- a/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
>> +++ b/Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml
>> @@ -83,6 +83,7 @@ allOf:
>>            contains:
>>              enum:
>>                - x-powers,axp313a
>> +              - x-powers,axp318w
>>                - x-powers,axp323
>>                - x-powers,axp15060
>>                - x-powers,axp717
>
> [Severity: Medium]
> Does the x-powers,axp318w compatible string also need to be added to the
> earlier if-then block that governs the interrupts requirement?

Ahhh, got it the other way around first time this poped - resending ...

>
> Just above this hunk in Documentation/devicetree/bindings/mfd/x-powers,axp152.yaml,
> there is a block that makes interrupts mandatory for all PMICs except a select
> few:
>
>   - if:
>       not:
>         properties:
>           compatible:
>             contains:
>               enum:
>                 - x-powers,axp15060
>                 - x-powers,axp305
>                 - x-powers,axp313a
>                 - x-powers,axp323
>
>     then:
>       required:
>         - interrupts
>
> By omitting x-powers,axp318w from this enum, the interrupts property is
> mandatory for the new PMIC. Could this cause device trees with an unconnected
> AXP318W interrupt line to falsely fail dt_binding_check validation, given that
> similar recent generation PMICs operate fine without it?
>
> -- 
> Sashiko AI review · https://sashiko.dev/#/patchset/20260910-axp318-regulator-v7-0-de720ceb9bac@baylibre.com?part=3

-- 
Jerome