[PATCH v5 0/3] arm64: dts: freescale: add Free Mobile Nodebox v3 CPU Module (LX2160A)

[PATCH v5 0/3] arm64: dts: freescale: add Free Mobile Nodebox v3 CPU Module (LX2160A)

[Vincent Jardin via B4 Relay]

The Nodebox v3 is a Free Mobile CPU module built around the NXP LX2160A
(16x Cortex-A72, DPAA2).

The same fsl-lx2160a-nbxv3.dtsi shall be used verbatim by the
U-Boot port, sent in parallel to the U-Boot list, so the two trees
cannot drift.

Dependency:

the DTS uses gpio hogs on the QorIQ GPIO controllers, which
needs the commit
  78c0baf85cd0 ("dt-bindings: gpio: fsl,qoriq-gpio: allow gpio-hog child nodes")
already in gpio/for-next and that will likely arrive in v7.4-rc1.
Until it lands, dtbs_check reports the five hog nodes, the rest of the
tree validates clean against the current schemas.

Signed-off-by: Vincent Jardin <vjardin@free.fr>
---
Changes in v5:
- read dts-coding-style: many reorder/cleanup including
  comments from Frank Li without functional changes
- Link to v4: https://lore.kernel.org/r/20260911-for-upstream-nbxv3-dts-v4-0-2fd07d5575ab@free.fr

Changes in v4:
- dt-bindings: arm: fsl: commit message like the other ones (Krzysztof Kozlowski)
- Acked-by on the vendor prefix
- Drop U-Boot comments from the DTS commit message (Frank Li)
- Boot NOR reset: reset-gpios on flash@0 instead of a gpio hog (Frank Li)
- ethsw-mdio-en: regulator-fixed instead of a gpio hog (Frank Li)
- ethsw-reset#: hog dropped (Frank Li)
- pltrst#: platform without consumer node
- Link to v3: https://lore.kernel.org/r/20260908-for-upstream-nbxv3-dts-v3-0-1d88b2c11680@free.fr

Changes in v3:
- Drop the thermtrip hog on gpio1 line 23, should have been clean'd
  before
- Link to v2: https://lore.kernel.org/r/20260907-for-upstream-nbxv3-dts-v2-0-6b4afd36180b@free.fr

Changes in v2: (from Sashiko's comments)
- Makefile: dtb entry in alphabetical order (before qds).
- Move the XSPI1_A_DATA[7:4] GPIO mux group from &fspi to &gpio1, so
  the reset hogs on gpio1 do not depend on the fspi probe.
- gpio hogs: describe ethsw-reset# and ethsw-mdio-en with their
  active-low polarity (GPIO_ACTIVE_LOW), same electrical levels.
- Link to v1: https://lore.kernel.org/r/20260907-for-upstream-nbxv3-dts-v1-0-f43fd0028b78@free.fr

---
Vincent Jardin (3):
      dt-bindings: vendor-prefixes: add Free Mobile
      dt-bindings: arm: fsl: add Free Mobile Nodebox v3 CPU Module
      arm64: dts: freescale: add Nodebox v3 CPU Module

 Documentation/devicetree/bindings/arm/fsl.yaml     |   6 +
 .../devicetree/bindings/vendor-prefixes.yaml       |   2 +
 arch/arm64/boot/dts/freescale/Makefile             |   2 +
 .../arm64/boot/dts/freescale/fsl-lx2160a-nbxv3.dts |  34 +++
 .../boot/dts/freescale/fsl-lx2160a-nbxv3.dtsi      | 330 +++++++++++++++++++++
 5 files changed, 374 insertions(+)
---
base-commit: df2908090cda368b01ff43709f51890076c56157
change-id: 20260907-for-upstream-nbxv3-dts-bbecd04038a2

Best regards,
-- 
Vincent Jardin <vjardin@free.fr>

[PATCH v5 1/3] dt-bindings: vendor-prefixes: add Free Mobile

[Vincent Jardin via B4 Relay]

From: Vincent Jardin <vjardin@free.fr>

Free Mobile is a French mobile network operator. Add its vendor
prefix, used by the Nodebox v3 CPU Module (freemobile,nbxv3).

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Vincent Jardin <vjardin@free.fr>
---
 Documentation/devicetree/bindings/vendor-prefixes.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
index ba2002969373..e467da45cd7a 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
+++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
@@ -626,6 +626,8 @@ patternProperties:
     description: Freebox SAS
   "^freecom,.*":
     description: Freecom Gmbh
+  "^freemobile,.*":
+    description: Free Mobile
   "^frida,.*":
     description: Shenzhen Frida LCD Co., Ltd.
   "^friendlyarm,.*":

-- 
2.43.0

[PATCH v5 2/3] dt-bindings: arm: fsl: add Free Mobile Nodebox v3 CPU Module

[Vincent Jardin via B4 Relay]

From: Vincent Jardin <vjardin@free.fr>

Add DT compatible string for the Free Mobile Nodebox v3 CPU Module, an
NXP LX2160A based board.

Signed-off-by: Vincent Jardin <vjardin@free.fr>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 656f2596e1d5..baff4f4159b2 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1937,6 +1937,12 @@ properties:
               - fsl,lx2162a-qds
           - const: fsl,lx2160a
 
+      - description: Free Mobile LX2160A based Boards
+        items:
+          - enum:
+              - freemobile,nbxv3
+          - const: fsl,lx2160a
+
       - description: SolidRun LX2160A CEX-7 based Boards
         items:
           - enum:

-- 
2.43.0

[PATCH v5 3/3] arm64: dts: freescale: add Nodebox v3 CPU Module

[Vincent Jardin via B4 Relay]

From: Vincent Jardin <vjardin@free.fr>

The Nodebox v3 is a Free Mobile CPU module built around the NXP
LX2160A (16x Cortex-A72, DPAA2).

Signed-off-by: Vincent Jardin <vjardin@free.fr>
---
 arch/arm64/boot/dts/freescale/Makefile             |   2 +
 .../arm64/boot/dts/freescale/fsl-lx2160a-nbxv3.dts |  34 +++
 .../boot/dts/freescale/fsl-lx2160a-nbxv3.dtsi      | 330 +++++++++++++++++++++
 3 files changed, 366 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 95ae85ab4adf..faab8bf0e167 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -55,6 +55,8 @@ DTC_FLAGS_fsl-lx2160a-half-twins := -Wno-interrupt_map
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-half-twins.dtb
 DTC_FLAGS_fsl-lx2160a-honeycomb := -Wno-interrupt_map
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-honeycomb.dtb
+DTC_FLAGS_fsl-lx2160a-nbxv3 := -Wno-interrupt_map
+dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-nbxv3.dtb
 DTC_FLAGS_fsl-lx2160a-qds := -Wno-interrupt_map
 dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-qds.dtb
 DTC_FLAGS_fsl-lx2160a-rdb := -Wno-interrupt_map
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-nbxv3.dts b/arch/arm64/boot/dts/freescale/fsl-lx2160a-nbxv3.dts
new file mode 100644
index 000000000000..cc02204e9d1b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-nbxv3.dts
@@ -0,0 +1,34 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Free Mobile Nodebox v3 CPU Module (LX2160A)
+ *
+ * Copyright 2026 Free Mobile, Vincent Jardin
+ */
+
+/dts-v1/;
+
+#include "fsl-lx2160a-rev2.dtsi"
+#include "fsl-lx2160a-nbxv3.dtsi"
+
+/ {
+	compatible = "freemobile,nbxv3", "fsl,lx2160a";
+	model = "Free Mobile Nodebox v3 CPU Module (LX2160A)";
+};
+
+&fspi {
+	pinctrl-0 = <&fspi_dqs_sck_cs10_pins>, <&fspi_data30_pins>;
+	pinctrl-names = "default";
+};
+
+&gpio1 {
+	pinctrl-0 = <&gpio1_31_28_pins>;
+	pinctrl-names = "default";
+};
+
+&pcs_mdio13 {
+	status = "okay";
+};
+
+&pcs_mdio14 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-nbxv3.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a-nbxv3.dtsi
new file mode 100644
index 000000000000..ca4fb5329c0b
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-nbxv3.dtsi
@@ -0,0 +1,330 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Free Mobile Nodebox v3 CPU Module (LX2160A)
+ *
+ * Copyright 2026 Free Mobile, Vincent Jardin
+ *
+ * This file is shared by the Linux kernel and U-Boot.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	gpio-restart {
+		compatible = "gpio-restart";
+		gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
+		priority = <128>;
+	};
+
+	reg_ethsw_mdio: regulator-ethsw-mdio {
+		compatible = "regulator-fixed";
+		gpio = <&gpio3 25 GPIO_ACTIVE_LOW>;
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-name = "ethsw-mdio-en";
+	};
+};
+
+&crypto {
+	status = "okay";
+};
+
+&dpmac13 {
+	phy-connection-type = "10gbase-r";
+	phy-handle = <&lan8023_phy_s0>;
+
+	status = "okay";
+};
+
+&dpmac14 {
+	phy-connection-type = "10gbase-r";
+	phy-handle = <&lan8023_phy_s1>;
+
+	status = "okay";
+};
+
+&dpmac17 {
+	phy-connection-type = "rgmii-id";
+	phy-handle = <&rtl8211fd>;
+
+	status = "okay";
+};
+
+&dspi0 {
+	status = "okay";
+
+	dpll@0 {
+		compatible = "microchip,zl30733";
+		reg = <0>;
+		spi-max-frequency = <12500000>;
+	};
+};
+
+&dspi2 {
+	status = "okay";
+};
+
+&emdio1 {
+	status = "okay";
+
+	/* Microchip LAN8023 dual 10G PCS/retimer, Clause 45 only, one address per slice */
+	lan8023_phy_s0: ethernet-phy@2 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <2>;
+	};
+
+	lan8023_phy_s1: ethernet-phy@3 {
+		compatible = "ethernet-phy-ieee802.3-c45";
+		reg = <3>;
+	};
+
+	rtl8211fd: ethernet-phy@6 {
+		compatible = "ethernet-phy-id001c.c916";
+		reg = <6>;
+	};
+};
+
+&emdio2 {
+	status = "okay";
+};
+
+&esdhc1 {
+	bus-width = <8>;
+	mmc-hs200-1_8v;
+	mmc-hs400-1_8v;
+	non-removable;
+
+	status = "okay";
+};
+
+&fsl_mc {
+	status = "okay";
+};
+
+&fspi {
+	status = "okay";
+
+	/* GigaDevice GD55LB02GF, 256 MiB boot NOR */
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reset-gpios = <&gpio1 28 GPIO_ACTIVE_LOW>;
+		spi-max-frequency = <150000000>;
+		spi-rx-bus-width = <1>;
+		spi-tx-bus-width = <1>;
+	};
+};
+
+&gpio0 {
+	gpio-line-names =
+		"", "",
+		"altfn:iic1-sda", "altfn:iic1-scl",
+		"altfn:uart4-sin", "altfn:uart4-sout",
+		"altfn:uart2-sin", "altfn:uart2-sout",
+		"altfn:uart3-sin", "altfn:uart3-sout",
+		"altfn:uart1-sin", "altfn:uart1-sout",
+		"altfn:spi3-pcs3", "altfn:spi3-pcs2",
+		"altfn:spi3-pcs1", "altfn:spi3-pcs0",
+		"altfn:spi1-sck", "altfn:spi1-sin",
+		"altfn:spi1-pcs2", "altfn:spi1-pcs1",
+		"altfn:spi1-pcs0", "altfn:spi1-sout",
+		"altfn:iic6-sda", "altfn:iic6-scl",
+		"altfn:spi3-sin", "altfn:spi3-sout",
+		"altfn:iic4-sda", "altfn:iic4-scl",
+		"altfn:iic3-sda", "altfn:iic3-scl",
+		"altfn:iic2-sda", "altfn:iic2-scl";
+
+	status = "okay";
+};
+
+&gpio1 {
+	gpio-line-names =
+		"", "", "", "", "", "",
+		"cfg-rcw-src2", "cfg-rcw-src3",
+		"reset-req-b",
+		"altfn:sdhc2-clk", "altfn:sdhc2-ds",
+		"altfn:sdhc2-dat0", "altfn:sdhc2-dat1",
+		"altfn:sdhc2-dat2", "altfn:sdhc2-dat3",
+		"altfn:sdhc2-dat4", "altfn:sdhc2-dat5",
+		"altfn:sdhc2-dat6", "altfn:sdhc2-dat7",
+		"altfn:sdhc2-cmd",
+		"cfg-svr1",
+		"altfn:xspi1-cs0", "altfn:xspi1-sck",
+		"altfn:xspi1-dqs",
+		"altfn:xspi1-data0", "altfn:xspi1-data1",
+		"", "",
+		"flash-reset#", "pltrst#", "", "ethsw-reset#";
+
+	status = "okay";
+
+	/* Platform reset, no consumer node: released at boot */
+	pltrst-hog {
+		gpio-hog;
+		gpios = <29 GPIO_ACTIVE_LOW>;
+		line-name = "pltrst#";
+		output-low;
+	};
+};
+
+&gpio2 {
+	gpio-line-names =
+		"lan8023-mdint",
+		"i2c2-alert#", "i2c4-alert#", "i2c6-alert#",
+		"u800-tca9539-int#",
+		"spi3-alert#",
+		"wake0", "wake1",
+		"carrier-hot#",
+		"u1300-rtl8211fd-int#",
+		"ethsw-int#",
+		"", "",
+		"u1700-zl30733-clk-gpio0", "u1700-zl30733-clk-gpio1",
+		"u1700-zl30733-clk-gpio2", "u1700-zl30733-clk-gpio3",
+		"", "", "", "", "", "", "", "",
+		"", "", "", "", "", "", "";
+
+	status = "okay";
+};
+
+&gpio3 {
+	gpio-line-names =
+		"altfn:ec1-txd3", "altfn:ec1-txd2",
+		"altfn:ec1-txd1", "altfn:ec1-txd0",
+		"altfn:ec1-tx-en", "altfn:ec1-gtx-clk",
+		"altfn:ec1-rxd3", "altfn:ec1-rxd2",
+		"altfn:ec1-rxd1", "altfn:ec1-rxd0",
+		"altfn:ec1-rx-clk", "altfn:ec1-rx-dv",
+		"", "",
+		"ptp-refclk-in",
+		"", "", "", "", "", "", "", "",
+		"u1700-zl30733-pps-out",
+		"",
+		"ethsw-mdio-en",
+		"usb01-oc#",	/* USB1_PWRFAULT and USB2_PWRFAULT share one net */
+		"",
+		"usb01-oc#",
+		"altfn:spi3-sck",
+		"", "";
+
+	status = "okay";
+};
+
+/* On-module management bus */
+&i2c0 {
+	status = "okay";
+
+	/* +0V8_VDD core rail, MPS MPQ8646 (MPQ8785 core) over PMBus */
+	vdd08: regulator@10 {
+		compatible = "mps,mpq8646";
+		reg = <0x10>;
+	};
+
+	/* SO-DIMM SPD temperature sensors */
+	temperature-sensor@18 {
+		compatible = "jedec,jc-42.4-temp";
+		reg = <0x18>;
+	};
+
+	temperature-sensor@19 {
+		compatible = "jedec,jc-42.4-temp";
+		reg = <0x19>;
+	};
+
+	eeprom@52 {
+		compatible = "atmel,24c32";
+		reg = <0x52>;
+		pagesize = <32>;
+	};
+
+	/* Board ID straps */
+	gpio@74 {
+		compatible = "ti,tca9539";
+		reg = <0x74>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		gpio-line-names =
+			"boardid-0x0001", "boardid-0x0002",
+			"boardid-0x0004", "boardid-0x0008",
+			"boardid-0x0010", "boardid-0x0020",
+			"boardid-0x0040", "boardid-0x0080",
+			"boardid-0x0100", "boardid-0x0200",
+			"boardid-0x0400", "boardid-0x0800",
+			"boardid-0x1000", "boardid-0x2000",
+			"boardid-0x4000", "boardid-0x8000";
+	};
+
+	u800: gpio@75 {
+		compatible = "ti,tca9539";
+		reg = <0x75>;
+		#gpio-cells = <2>;
+		#interrupt-cells = <2>;
+		gpio-controller;
+		gpio-line-names =
+			"carrier-gpio0", "carrier-gpio1",
+			"carrier-gpio2", "carrier-gpio3",
+			"carrier-gpio4", "carrier-gpio5",
+			"carrier-gpio6", "carrier-gpio7",
+			"carrier-gpio8", "carrier-gpio9",
+			"carrier-gpio10", "carrier-gpio11",
+			"", "", "",
+			"lan8023-rst";
+		interrupt-controller;
+		interrupt-parent = <&gpio2>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
+	};
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
+
+&i2c3 {
+	status = "okay";
+};
+
+&i2c5 {
+	status = "okay";
+};
+
+&pcie3 {
+	status = "okay";
+};
+
+&pcie4 {
+	status = "okay";
+};
+
+&pcie5 {
+	status = "okay";
+};
+
+&pcie6 {
+	status = "okay";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};

-- 
2.43.0

Re: [PATCH v5 3/3] arm64: dts: freescale: add Nodebox v3 CPU Module

[sashiko-bot]

Thank you for your contribution! Sashiko AI review found 1 potential issue(s) to consider:
- [Medium] Ethernet PHY nodes are missing hardware interrupt and reset properties despite the hardware lines being explicitly routed and documented.
--

commit 15177a59c196f0e48927f297cc2ef90524059103
Author: Vincent Jardin <vjardin@free.fr>

arm64: dts: freescale: add Nodebox v3 CPU Module

This commit introduces device tree support for the Free Mobile Nodebox v3 CPU
module. The module is built around the NXP LX2160A SoC and includes support
for various interfaces including Ethernet, I2C, and PCI.

> diff --git a/arch/arm64/boot/dts/freescale/fsl-lx2160a-nbxv3.dtsi b/arch/arm64/boot/dts/freescale/fsl-lx2160a-nbxv3.dtsi
> new file mode 100644
> index 0000000000000..ca4fb5329c0b2
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/fsl-lx2160a-nbxv3.dtsi
[ ... ]
> +&emdio1 {
> +	status = "okay";
> +
> +	/* Microchip LAN8023 dual 10G PCS/retimer, Clause 45 only, one address per slice */
> +	lan8023_phy_s0: ethernet-phy@2 {
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		reg = <2>;
> +	};
> +
> +	lan8023_phy_s1: ethernet-phy@3 {
> +		compatible = "ethernet-phy-ieee802.3-c45";
> +		reg = <3>;
> +	};
> +
> +	rtl8211fd: ethernet-phy@6 {
> +		compatible = "ethernet-phy-id001c.c916";
> +		reg = <6>;
> +	};
> +};

[Severity: Medium]
Should these Ethernet PHY nodes include hardware interrupt and reset
properties?

Without the interrupts property, the kernel PHY state machine will fall back
to a 1-second polling interval, which increases latency and wastes CPU cycles.
Missing reset-gpios prevents the kernel from resetting the PHYs during probe,
leaving initialization reliant on the bootloader.

The hardware lines appear to be explicitly routed and documented below in the
gpio-line-names arrays.

[ ... ]
> +&gpio2 {
> +	gpio-line-names =
> +		"lan8023-mdint",
> +		"i2c2-alert#", "i2c4-alert#", "i2c6-alert#",
> +		"u800-tca9539-int#",
> +		"spi3-alert#",
> +		"wake0", "wake1",
> +		"carrier-hot#",
> +		"u1300-rtl8211fd-int#",
[ ... ]
> +	u800: gpio@75 {
> +		compatible = "ti,tca9539";
> +		reg = <0x75>;
> +		#gpio-cells = <2>;
> +		#interrupt-cells = <2>;
> +		gpio-controller;
> +		gpio-line-names =
> +			"carrier-gpio0", "carrier-gpio1",
> +			"carrier-gpio2", "carrier-gpio3",
> +			"carrier-gpio4", "carrier-gpio5",
> +			"carrier-gpio6", "carrier-gpio7",
> +			"carrier-gpio8", "carrier-gpio9",
> +			"carrier-gpio10", "carrier-gpio11",
> +			"", "", "",
> +			"lan8023-rst";

Is it intentional that lan8023-mdint and u1300-rtl8211fd-int# are defined
in &gpio2, and lan8023-rst is defined in u800, but they aren't linked to
their respective PHY nodes in &emdio1?

-- 
Sashiko AI review · https://sashiko.dev/#/patchset/20260912-for-upstream-nbxv3-dts-v5-0-ead604dba61b@free.fr?part=3

Re: [PATCH v5 2/3] dt-bindings: arm: fsl: add Free Mobile Nodebox v3 CPU Module

[Krzysztof Kozlowski]

On Sat, Sep 12, 2026 at 03:32:37PM +0200, Vincent Jardin wrote:
> Add DT compatible string for the Free Mobile Nodebox v3 CPU Module, an
> NXP LX2160A based board.
> 
> Signed-off-by: Vincent Jardin <vjardin@free.fr>
> ---
>  Documentation/devicetree/bindings/arm/fsl.yaml | 6 ++++++
>  1 file changed, 6 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
> index 656f2596e1d5..baff4f4159b2 100644
> --- a/Documentation/devicetree/bindings/arm/fsl.yaml
> +++ b/Documentation/devicetree/bindings/arm/fsl.yaml
> @@ -1937,6 +1937,12 @@ properties:
>                - fsl,lx2162a-qds
>            - const: fsl,lx2160a
>  
> +      - description: Free Mobile LX2160A based Boards

Why this cannot be part of "LX2160A based Boards"? And what other boards
are based on Free Mobile LX2160A?


Best regards,
Krzysztof