Devicetree
 help / color / mirror / Atom feed
* [PATCH v5 0/2] Add device tree for Acer Swift Go Pro AI (SFA14-11)
@ 2026-10-23 18:05 Kaipeng Zeng
  2026-10-23 18:05 ` [PATCH v5 1/2] dt-bindings: arm: qcom: Add " Kaipeng Zeng
                   ` (2 more replies)
  0 siblings, 3 replies; 5+ messages in thread
From: Kaipeng Zeng @ 2026-10-23 18:05 UTC (permalink / raw)
  To: devicetree
  Cc: linux-arm-msm, conor+dt, krzk+dt, robh, abelvesa, konradybcio,
	andersson, Kaipeng Zeng

The work started with x1-crd.dtsi as initial template.
HDMI refers to ThinkPad T14s.
Bluetooth refers to x1-crd.dtsi from the ubuntu-concept kernel [1].
PWM brightness control refers to Ratizux's GitHub repository [2].

Tested on linux-next (next-20261021: 9a482184) / Ubuntu 26.04 LTS.

Tested and working devices:
 - NVMe
 - Keyboard & Touchpad
 - USB Type-A, Type-C
 - Battery & charging status
 - Internal display & Backlight brightness control
 - HDMI & Type-C display (with audio)
 - Bluetooth & Wi-Fi
 - Webcam (usb_2)
 - GPU
 - Audio: speaker (partial), mic, headphone.

Known issues:
- Four internal speakers are detected, but only three work. I use Ratizux's tplg [3] and
  alsa configuration [4] on my desktop. I also use amixer & speaker-test to verify them.
- EL2-mode:
  - EL2-mode can only work with kernel parameter: "iommu.passthrough=1".
  - Audio and Battery status are broken under EL2 mode.
  - Bluetooth is broken under EL2 mode.

Also, some notes about eusb*_repeater and EC; hopefully, this can help others understand
why I configured these nodes this way:
- eusb*_repeater conflict between the DSDT and my testing:
  By using `i2ctransfer` to sequentially set the modes of 'eusb3/5/6_repeater', I can
  observe the corresponding connection or disconnection state changes for the
  right-side USB-A port ('usb_mp_hsphy0'), the left-side USB-A port ('usb_mp_hsphy1'),
  and the webcam ('usb_2'). Using `gpioset`, it can be verified that 'eusb6_repeater'
  is affected by tlmm's GPIO 184, while setting GPIO 6/7 has no effect. And webcam
  can be shut down and reset by toggling GPIO 184. The DSDT places GPIO 6/184 as a
  'ResourceTemplate' under 'USB3'(usb_mp), GPIO 7 under USB4(usb_2), and webcam is
  under USB4. This conflicts with my testing. So, I didn't add the unverified GPIO,
  and the connection between USB and repeater follows my testing rather than DSDT.
- There is an EC device under i2c5 at address 0x76, with driver probe failed.
  But using i2ctransfer I can observe some data changes related to fan.
  The EC driver appears to require additional work, and it couldn't be included in
  this patch. So, I didn't add that node.

[1] https://git.launchpad.net/~ubuntu-concept/ubuntu/+source/linux/+git/resolute
[2] https://github.com/Ratizux/linux-device-acer-sfa14-11.git
[3] https://github.com/Ratizux/audioreach-topology/
[4] https://github.com/Ratizux/alsa-ucm-conf

---
Changelog:

V5:
- Rebase to next-20261021, pick up the following upstream changes:
    arm64: dts: qcom: x1-crd: Mark the EC reset gpio as reserved (099cd579).
    arm64: dts: qcom: hamoa/purwa: Add QREF regulator supplies (d9d07e23).
    arm64: dts: qcom: hamoa: Fix swapped USB QMP PHY vdda-phy/vdda-pll supplies (4458dcd3).
- Add 'eusb*_repeater'. (Jianfeng Liu)
- Add 'displayport-2-dai-link'. (Jianfeng Liu)
- Remove 'usb_1_ss1' and 'mdss_dp1'. (Jianfeng Liu)
- Remove unused 'audio-routing'. (Jianfeng Liu)
- Remove 'kypd_vol_up_n'. (Jianfeng Liu)

V4:
- Add -el2-dtbs. (Sashiko)
- The "audio-routing" of "sound" is from x1-crd.dtsi, audio doesn't totally work,
  and I didn't see any improvements when I followed Sashiko's advice,
  so I just kept it the same as x1-crd.dtsi. (Sashiko)
- Tested in EL2 mode:
  Successfully boots with the kernel parameter: "iommu.passthrough=1",
  The above features work as in EL1 mode except battery status.
- Fix missing newline before "wsa-dai-link". (Val Packett)
- Link to V4: https://lore.kernel.org/linux-devicetree/20261006085425.40450-1-kaipeng94@gmail.com/

V3:
- Re-sort *-link and its sub-nodes. (Konrad Dybcio)
- Keep a '\n' before 'status'. (Konrad Dybcio)
- Remove 'output-low' from wcd_default. (Konrad Dybcio)
- Link to V3: https://lore.kernel.org/linux-devicetree/20260729064538.19564-1-kaipeng94@gmail.com/

V2:
- Fix Makefile entry ordering. (Krzysztof Kozlowski)
- Use readable compatible string. (Krzysztof Kozlowski)
- Fix sound card model name for this device. (Krzysztof Kozlowski & Konrad Dybcio)
- Re-sort nodes, pinctrl-*. (Krzysztof Kozlowski & Konrad Dybcio)
- Remove those regulators without consumer and lack of a required value in DSDT. (Konrad Dybcio)
- Remove ADSP/CDSP fastrpc memory. (Konrad Dybcio)
- Add iris firmware path. (Konrad Dybcio)
- Delete usb_1_ss1_qmpphy/usb_1_ss2_qmpphy properties of Type-C. (Sashiko)
- Delete usb_1_ss2_hsphy. (Sashiko)
- Remove unused pmic-glink orientation-gpio. (Sashiko)
- Remove node related to WWAN.

- The Webcam is a USB device, can be probed without any additional
  node. (Sashiko)
- Using reset-gpios in swr* seems common in X1E devices, like Lenovo
  Yoga Slim7x, ThinkPad t14s and Microsoft Romulus.
  Because speakers do not completely work and I could not see any
  effect of changing it, just retain it. (Sashiko)
- Also, the HDMI audio is the same reason as above. (Sashiko)
- Link to V2: https://lore.kernel.org/linux-devicetree/20260721082410.18275-1-kaipeng94@gmail.com/

- Link to V1: https://lore.kernel.org/linux-devicetree/20260702063156.35169-1-kaipeng94@gmail.com/

Kaipeng Zeng (2):
  dt-bindings: arm: qcom: Add Acer Swift Go Pro AI (SFA14-11)
  arm64: dts: qcom: Add support for Acer Swift Go Pro AI (SFA14-11)

 .../devicetree/bindings/arm/qcom.yaml         |    1 +
 arch/arm64/boot/dts/qcom/Makefile             |    2 +
 .../boot/dts/qcom/x1e78100-acer-sfa14-11.dts  | 1541 +++++++++++++++++
 3 files changed, 1544 insertions(+)
 create mode 100644 arch/arm64/boot/dts/qcom/x1e78100-acer-sfa14-11.dts


base-commit: 9a482184d910775cf648863148944945b74e2815
-- 
2.53.0


^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, other threads:[~2026-10-24  7:33 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-10-23 18:05 [PATCH v5 0/2] Add device tree for Acer Swift Go Pro AI (SFA14-11) Kaipeng Zeng
2026-10-23 18:05 ` [PATCH v5 1/2] dt-bindings: arm: qcom: Add " Kaipeng Zeng
2026-10-23 18:05 ` [PATCH v5 2/2] arm64: dts: qcom: Add support for " Kaipeng Zeng
2026-10-23 18:33   ` sashiko-bot
2026-10-24  7:33 ` [PATCH v5 0/2] Add device tree " Jianfeng Liu

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox