* [PATCH v2 2/3] dt-bindings: iio: proximity: Add Benewake TF-Luna
2026-10-30 18:53 [PATCH v2 0/3] iio: proximity: Add Benewake TF-Luna LiDAR driver Vidhu Sarwal via B4 Relay
2026-10-30 18:53 ` [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add Benewake Vidhu Sarwal via B4 Relay
@ 2026-10-30 18:53 ` Vidhu Sarwal via B4 Relay
2026-10-30 18:53 ` [PATCH v2 3/3] iio: proximity: Add Benewake TF-Luna LiDAR driver Vidhu Sarwal via B4 Relay
2 siblings, 0 replies; 4+ messages in thread
From: Vidhu Sarwal via B4 Relay @ 2026-10-30 18:53 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Vidhu Sarwal,
Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko
Cc: devicetree, linux-kernel, linux-iio, Shuah Khan
From: Vidhu Sarwal <vidhu.linux@gmail.com>
Add binding for the Benewake TF-Luna, a single point ToF
LiDAR distance sensor with a range of 0.2 m to 8 m.
The sensor talks either UART or I2C, selected by the level of pin 5 at
power-up. This binding covers both interfaces. Pin 6 is a data ready
output and is described as an interrupt.
Signed-off-by: Vidhu Sarwal <vidhu.linux@gmail.com>
---
.../bindings/iio/proximity/benewake,tf-luna.yaml | 66 ++++++++++++++++++++++
MAINTAINERS | 6 ++
2 files changed, 72 insertions(+)
diff --git a/Documentation/devicetree/bindings/iio/proximity/benewake,tf-luna.yaml b/Documentation/devicetree/bindings/iio/proximity/benewake,tf-luna.yaml
new file mode 100644
index 000000000000..607a71a6ab39
--- /dev/null
+++ b/Documentation/devicetree/bindings/iio/proximity/benewake,tf-luna.yaml
@@ -0,0 +1,66 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/iio/proximity/benewake,tf-luna.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Benewake TF-Luna LiDAR distance sensor
+
+maintainers:
+ - Vidhu Sarwal <vidhu.linux@gmail.com>
+
+description: |
+ Single-point time-of-flight LiDAR ranging sensor with a range of 0.2 m to
+ 8 m. The sensor talks either UART or I2C, selected at power-up by the level
+ of pin 5: tied to ground for I2C, unconnected or tied to 3.3 V for UART.
+
+ Datasheet: https://en.benewake.com/uploadfiles/2025/04/20250430174501874.pdf
+
+properties:
+ compatible:
+ const: benewake,tf-luna
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ description:
+ Output on pin 6. In I2C mode it is a data ready signal that goes high
+ when a new measurement is available and goes low again once any
+ register has been read. In UART mode it can be configured as an on/off
+ output.
+ maxItems: 1
+
+ vcc-supply:
+ description: Power supply, 3.7 V to 5.2 V.
+
+required:
+ - compatible
+ - vcc-supply
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ proximity@10 {
+ compatible = "benewake,tf-luna";
+ reg = <0x10>;
+ vcc-supply = <®_5v>;
+ interrupt-parent = <&gpio>;
+ interrupts = <17 IRQ_TYPE_EDGE_RISING>;
+ };
+ };
+ - |
+ serial {
+ proximity {
+ compatible = "benewake,tf-luna";
+ vcc-supply = <®_5v>;
+ };
+ };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 52024397dc78..24fa7cdf6a57 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4662,6 +4662,12 @@ T: git git://git.kernel.org/pub/scm/linux/kernel/git/luisbg/linux-befs.git
F: Documentation/filesystems/befs.rst
F: fs/befs/
+BENEWAKE TF-LUNA LIDAR IIO DRIVER
+M: Vidhu Sarwal <vidhu.linux@gmail.com>
+L: linux-iio@vger.kernel.org
+S: Maintained
+F: Documentation/devicetree/bindings/iio/proximity/benewake,tf-luna.yaml
+
BFQ I/O SCHEDULER
M: Yu Kuai <yukuai@fygo.io>
L: linux-block@vger.kernel.org
--
2.53.0
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH v2 3/3] iio: proximity: Add Benewake TF-Luna LiDAR driver
2026-10-30 18:53 [PATCH v2 0/3] iio: proximity: Add Benewake TF-Luna LiDAR driver Vidhu Sarwal via B4 Relay
2026-10-30 18:53 ` [PATCH v2 1/3] dt-bindings: vendor-prefixes: Add Benewake Vidhu Sarwal via B4 Relay
2026-10-30 18:53 ` [PATCH v2 2/3] dt-bindings: iio: proximity: Add Benewake TF-Luna Vidhu Sarwal via B4 Relay
@ 2026-10-30 18:53 ` Vidhu Sarwal via B4 Relay
2 siblings, 0 replies; 4+ messages in thread
From: Vidhu Sarwal via B4 Relay @ 2026-10-30 18:53 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Vidhu Sarwal,
Jonathan Cameron, David Lechner, Nuno Sá, Andy Shevchenko
Cc: devicetree, linux-kernel, linux-iio, Shuah Khan
From: Vidhu Sarwal <vidhu.linux@gmail.com>
Add a driver for the Benewake TF-Luna, a single-point time-of-flight
LiDAR distance sensor with a range of 0.2 m to 8 m, connected over I2C.
The sensor is run in trigger mode. Each read starts one measurement and
waits for the timestamp register to change before reading the result.
In continuous mode a read can catch the sensor in the middle of updating
its result registers unless it is synchronised to the data ready output,
which this driver does not use yet.
When the signal strength is too low the sensor reports a dummy distance
of 0, so such readings, as well as overexposed ones, return -ENODATA
instead of a distance.
Datasheet: https://en.benewake.com/uploadfiles/2025/04/20250430174501874.pdf
Signed-off-by: Vidhu Sarwal <vidhu.linux@gmail.com>
---
MAINTAINERS | 1 +
drivers/iio/proximity/Kconfig | 11 ++
drivers/iio/proximity/Makefile | 1 +
drivers/iio/proximity/tf-luna.c | 260 ++++++++++++++++++++++++++++++++++++++++
4 files changed, 273 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index 24fa7cdf6a57..20e43a003bed 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -4667,6 +4667,7 @@ M: Vidhu Sarwal <vidhu.linux@gmail.com>
L: linux-iio@vger.kernel.org
S: Maintained
F: Documentation/devicetree/bindings/iio/proximity/benewake,tf-luna.yaml
+F: drivers/iio/proximity/tf-luna.c
BFQ I/O SCHEDULER
M: Yu Kuai <yukuai@fygo.io>
diff --git a/drivers/iio/proximity/Kconfig b/drivers/iio/proximity/Kconfig
index f3cec799df67..d16458ea4b0f 100644
--- a/drivers/iio/proximity/Kconfig
+++ b/drivers/iio/proximity/Kconfig
@@ -222,6 +222,17 @@ config SRF08
To compile this driver as a module, choose M here: the
module will be called srf08.
+config TF_LUNA
+ tristate "Benewake TF-Luna LiDAR distance sensor"
+ depends on I2C
+ select REGMAP_I2C
+ help
+ Say Y here to build a driver for the Benewake TF-Luna LiDAR
+ distance sensor connected over I2C.
+
+ To compile this driver as a module, choose M here: the
+ module will be called tf-luna.
+
config VCNL3020
tristate "VCNL3020 proximity sensor"
select REGMAP_I2C
diff --git a/drivers/iio/proximity/Makefile b/drivers/iio/proximity/Makefile
index 8a65e42fbea0..43741115a921 100644
--- a/drivers/iio/proximity/Makefile
+++ b/drivers/iio/proximity/Makefile
@@ -21,6 +21,7 @@ obj-$(CONFIG_SX9324) += sx9324.o
obj-$(CONFIG_SX9360) += sx9360.o
obj-$(CONFIG_SX_COMMON) += sx_common.o
obj-$(CONFIG_SX9500) += sx9500.o
+obj-$(CONFIG_TF_LUNA) += tf-luna.o
obj-$(CONFIG_VCNL3020) += vcnl3020.o
obj-$(CONFIG_VCNL36829) += vcnl36829.o
obj-$(CONFIG_VL53L0X_I2C) += vl53l0x-i2c.o
diff --git a/drivers/iio/proximity/tf-luna.c b/drivers/iio/proximity/tf-luna.c
new file mode 100644
index 000000000000..dbb56e7414af
--- /dev/null
+++ b/drivers/iio/proximity/tf-luna.c
@@ -0,0 +1,260 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Benewake TF-Luna LiDAR distance sensor
+ *
+ * Copyright (C) 2026 Vidhu Sarwal <vidhu.linux@gmail.com>
+ *
+ * Datasheet: https://en.benewake.com/uploadfiles/2025/04/20250430174501874.pdf
+ *
+ * The I2C register map is in appendix III of the TF-Luna product manual
+ * (SJ-PM-TF-Luna A05). Default 7-bit I2C address is 0x10.
+ */
+
+#include <linux/array_size.h>
+#include <linux/bits.h>
+#include <linux/cleanup.h>
+#include <linux/delay.h>
+#include <linux/dev_printk.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
+#include <linux/time.h>
+#include <linux/types.h>
+
+#include <asm/byteorder.h>
+
+#include <linux/iio/iio.h>
+
+#define TF_LUNA_REG_DIST 0x00
+#define TF_LUNA_REG_TICK 0x06
+#define TF_LUNA_REG_VERSION 0x0A
+#define TF_LUNA_REG_MODE 0x23
+#define TF_LUNA_REG_TRIG_ONE_SHOT 0x24
+#define TF_LUNA_REG_SIGNATURE 0x3C
+
+#define TF_LUNA_MODE_TRIGGER 0x01
+#define TF_LUNA_TRIG_ONE_SHOT 0x01
+
+#define TF_LUNA_SIGN 0x4c554e41 /* "LUNA" in ASCII */
+
+/* Below this the sensor reports a dummy distance of 0 */
+#define TF_LUNA_AMP_MIN 100
+#define TF_LUNA_AMP_OVEREXPOSED 0xFFFF
+
+/* A measurement takes 10-20 ms in trigger mode */
+#define TF_LUNA_POLL_US (2 * USEC_PER_MSEC)
+#define TF_LUNA_TIMEOUT_US (100 * USEC_PER_MSEC)
+
+struct tf_luna_data {
+ struct regmap *regmap;
+ /* Serialises the trigger, poll and read of a single measurement */
+ struct mutex lock;
+};
+
+/*
+ * No register cache: the only configuration register written is MODE,
+ * once in probe, the other write is the one-shot trigger, and the
+ * registers read afterwards hold measurement data that keeps changing.
+ * MODE is also read back from the hardware, since the sensor can
+ * silently ignore a write that comes right after another one.
+ */
+static const struct regmap_config tf_luna_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = TF_LUNA_REG_SIGNATURE + 3,
+};
+
+static int tf_luna_read_tick(struct tf_luna_data *data, u16 *tick)
+{
+ __le16 val;
+ int ret;
+
+ ret = regmap_bulk_read(data->regmap, TF_LUNA_REG_TICK, &val, sizeof(val));
+ if (ret)
+ return ret;
+
+ *tick = le16_to_cpu(val);
+ return 0;
+}
+
+static int tf_luna_measure(struct tf_luna_data *data, int *dist)
+{
+ struct regmap *map = data->regmap;
+ __le16 buf[2]; /* distance in cm, signal strength */
+ u16 old_tick, tick, amp;
+ int ret, err;
+
+ guard(mutex)(&data->lock);
+
+ ret = tf_luna_read_tick(data, &old_tick);
+ if (ret)
+ return ret;
+
+ ret = regmap_write(map, TF_LUNA_REG_TRIG_ONE_SHOT, TF_LUNA_TRIG_ONE_SHOT);
+ if (ret)
+ return ret;
+
+ /* The tick register is a timestamp, it changes with each measurement */
+ ret = read_poll_timeout(tf_luna_read_tick, err, err || tick != old_tick,
+ TF_LUNA_POLL_US, TF_LUNA_TIMEOUT_US, true,
+ data, &tick);
+ if (ret)
+ return ret;
+ if (err)
+ return err;
+
+ ret = regmap_bulk_read(map, TF_LUNA_REG_DIST, buf, sizeof(buf));
+ if (ret)
+ return ret;
+
+ amp = le16_to_cpu(buf[1]);
+ if (amp < TF_LUNA_AMP_MIN || amp == TF_LUNA_AMP_OVEREXPOSED)
+ return -ENODATA;
+
+ *dist = le16_to_cpu(buf[0]);
+ return 0;
+}
+
+static int tf_luna_read_raw(struct iio_dev *indio_dev,
+ struct iio_chan_spec const *chan,
+ int *val, int *val2, long mask)
+{
+ struct tf_luna_data *data = iio_priv(indio_dev);
+ int ret;
+
+ switch (mask) {
+ case IIO_CHAN_INFO_RAW:
+ ret = tf_luna_measure(data, val);
+ if (ret)
+ return ret;
+ return IIO_VAL_INT;
+ case IIO_CHAN_INFO_SCALE:
+ /* Distance is in cm */
+ *val = 0;
+ *val2 = 10000;
+ return IIO_VAL_INT_PLUS_MICRO;
+ default:
+ return -EINVAL;
+ }
+}
+
+static const struct iio_info tf_luna_info = {
+ .read_raw = tf_luna_read_raw,
+};
+
+static const struct iio_chan_spec tf_luna_channels[] = {
+ {
+ .type = IIO_DISTANCE,
+ .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) |
+ BIT(IIO_CHAN_INFO_SCALE),
+ },
+};
+
+static int tf_luna_probe(struct i2c_client *client)
+{
+ struct device *dev = &client->dev;
+ struct tf_luna_data *data;
+ struct iio_dev *indio_dev;
+ struct regmap *map;
+ unsigned int mode;
+ __be32 sign;
+ u32 fourcc;
+ u8 ver[3];
+ int ret;
+
+ indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
+ if (!indio_dev)
+ return -ENOMEM;
+
+ data = iio_priv(indio_dev);
+
+ ret = devm_mutex_init(dev, &data->lock);
+ if (ret)
+ return ret;
+
+ map = devm_regmap_init_i2c(client, &tf_luna_regmap_config);
+ if (IS_ERR(map))
+ return dev_err_probe(dev, PTR_ERR(map), "Failed to initialize regmap\n");
+ data->regmap = map;
+
+ ret = devm_regulator_get_enable(dev, "vcc");
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to enable vcc regulator\n");
+
+ /* Boot time is not documented, about 350 ms was measured */
+ msleep(500);
+
+ ret = regmap_bulk_read(map, TF_LUNA_REG_SIGNATURE, &sign, sizeof(sign));
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to read signature\n");
+
+ fourcc = be32_to_cpu(sign);
+ if (fourcc != TF_LUNA_SIGN)
+ dev_info(dev, "Unknown signature %p4ch, continuing\n", &fourcc);
+
+ ret = regmap_bulk_read(map, TF_LUNA_REG_VERSION, ver, sizeof(ver));
+ if (ret)
+ return ret;
+
+ dev_dbg(dev, "Firmware version %u.%u.%u\n", ver[2], ver[1], ver[0]);
+
+ /*
+ * In continuous mode a read can catch the sensor updating its result
+ * registers unless it is synchronised to the data ready output. Use
+ * trigger mode and start each measurement on demand instead.
+ */
+ ret = regmap_write(map, TF_LUNA_REG_MODE, TF_LUNA_MODE_TRIGGER);
+ if (ret)
+ return ret;
+
+ /*
+ * The sensor silently drops writes it is not ready for, so check that
+ * the mode was set. A write takes up to 100 ms to read back.
+ */
+ msleep(100);
+
+ ret = regmap_read(map, TF_LUNA_REG_MODE, &mode);
+ if (ret)
+ return ret;
+
+ if (mode != TF_LUNA_MODE_TRIGGER)
+ return dev_err_probe(dev, -EIO, "Failed to set trigger mode\n");
+
+ indio_dev->name = "tf-luna";
+ indio_dev->info = &tf_luna_info;
+ indio_dev->channels = tf_luna_channels;
+ indio_dev->num_channels = ARRAY_SIZE(tf_luna_channels);
+ indio_dev->modes = INDIO_DIRECT_MODE;
+
+ return devm_iio_device_register(dev, indio_dev);
+}
+
+static const struct i2c_device_id tf_luna_id[] = {
+ { .name = "tf-luna" },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, tf_luna_id);
+
+static const struct of_device_id tf_luna_of_match[] = {
+ { .compatible = "benewake,tf-luna" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, tf_luna_of_match);
+
+static struct i2c_driver tf_luna_driver = {
+ .driver = {
+ .name = "tf-luna",
+ .of_match_table = tf_luna_of_match,
+ },
+ .probe = tf_luna_probe,
+ .id_table = tf_luna_id,
+};
+module_i2c_driver(tf_luna_driver);
+
+MODULE_AUTHOR("Vidhu Sarwal <vidhu.linux@gmail.com>");
+MODULE_DESCRIPTION("Benewake TF-Luna LiDAR distance sensor driver");
+MODULE_LICENSE("GPL");
--
2.53.0
^ permalink raw reply related [flat|nested] 4+ messages in thread