* [PATCH 0/3] Add PWM support for the Sophgo CV1800B
@ 2026-11-17 12:57 Hiago De Franco
2026-11-17 12:57 ` [PATCH 1/3] dt-bindings: pwm: sophgo: add PWM controller for CV1800B Hiago De Franco
` (2 more replies)
0 siblings, 3 replies; 5+ messages in thread
From: Hiago De Franco @ 2026-11-17 12:57 UTC (permalink / raw)
To: Uwe Kleine-König, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Chen Wang, Inochi Amaoto, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Chen Wang, linux-pwm, devicetree, sophgo, linux-kernel,
linux-riscv
This series adds support for the PWM controller of the Sophgo CV1800B,
the SoC used on the Milk-V Duo. The same block is also found on the
CV181x and SG200x, which share cv180x.dtsi.
The CV1800B has four PWM controller instances at 0x03060000, 0x03061000,
0x03062000 and 0x03063000, each with four channels, for 16 outputs in
total. The register layout is derived from the controller already
supported by drivers/pwm/pwm-sophgo-sg2042.c, so instead of adding a
separate driver the new SoC is handled by a new chip_data variant in that
driver, as suggested during the review of the previous submissions [1].
Compared to the SG2044, the CV1800B differs in these points:
- PERIOD and HLPERIOD are 30 bits wide and PERIOD must be strictly
greater than HLPERIOD. A 100% duty cycle is therefore not
representable, and the period must be at least two input clock cycles.
- POLARITY has the opposite meaning: with bit 0, HLPERIOD counts the low
part of the period and the pin idles low; with bit 1, HLPERIOD counts
the high part and the pin idles high.
- A POLARITY change takes effect immediately, even while the channel is
running, and does not need PWMUPDATE.
- HLPERIOD/PERIOD written while the channel is running are only latched
on a 0 -> 1 transition of PWMUPDATE. Toggling PWMSTART must not be used
for that, as it restarts the counter.
- When the counter is stopped the pin is parked at the level selected by
POLARITY; emitting the inactive level would require changing POLARITY, so
the driver switches the pin to input mode while the channel is disabled.
Patch 1 extends the DT binding, patch 2 adds the CV1800B variant to the
driver and updates the Kconfig help text, and patch 3 adds the
controller nodes to the shared cv180x.dtsi.
The hardware behaviour described above was verified on a Milk-V Duo with
a logic analyzer (GP4 routed to PWM, i.e. pwm1 channel 1), at 1 kHz/25%
and at 0.5 Hz: polarity mapping, PWMUPDATE latching with a running
channel, and the pin state of a disabled channel.
This follows the earlier CV1800B PWM submissions by Jingbao Qiu (v1-v7)
and Thomas Bonnefille (v8).
[1] https://lore.kernel.org/lkml/20250509-pwm_sophgo-v8-0-cfaebeb8ee17@bootlin.com/
Signed-off-by: Hiago De Franco <hfranco@baylibre.com>
---
Hiago De Franco (3):
dt-bindings: pwm: sophgo: add PWM controller for CV1800B
pwm: sophgo-sg2042: add support for CV1800B
riscv: dts: sophgo: cv180x: add PWM controller nodes
.../devicetree/bindings/pwm/sophgo,sg2042-pwm.yaml | 3 +-
arch/riscv/boot/dts/sophgo/cv180x.dtsi | 40 ++++
drivers/pwm/Kconfig | 7 +-
drivers/pwm/pwm-sophgo-sg2042.c | 201 ++++++++++++++++++++-
4 files changed, 241 insertions(+), 10 deletions(-)
---
base-commit: 6628e7d4c6b25c8d18f1345e3a20d21829aae7e4
change-id: 20261104-milkv-duo-pwm-42fbc28b0693
Best regards,
--
Hiago
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/3] dt-bindings: pwm: sophgo: add PWM controller for CV1800B
2026-11-17 12:57 [PATCH 0/3] Add PWM support for the Sophgo CV1800B Hiago De Franco
@ 2026-11-17 12:57 ` Hiago De Franco
2026-11-17 17:28 ` Conor Dooley
2026-11-17 12:57 ` [PATCH 2/3] pwm: sophgo-sg2042: add support " Hiago De Franco
2026-11-17 12:57 ` [PATCH 3/3] riscv: dts: sophgo: cv180x: add PWM controller nodes Hiago De Franco
2 siblings, 1 reply; 5+ messages in thread
From: Hiago De Franco @ 2026-11-17 12:57 UTC (permalink / raw)
To: Uwe Kleine-König, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Chen Wang, Inochi Amaoto, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Chen Wang, linux-pwm, devicetree, sophgo, linux-kernel,
linux-riscv
The Sophgo CV1800B SoC has four PWM controller instances that are
derived from the controllers found on the SG2042 and SG2044 SoCs.
Add the "sophgo,cv1800b-pwm" compatible string and update the binding
title to cover all supported SoCs.
Signed-off-by: Hiago De Franco <hfranco@baylibre.com>
---
Documentation/devicetree/bindings/pwm/sophgo,sg2042-pwm.yaml | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/pwm/sophgo,sg2042-pwm.yaml b/Documentation/devicetree/bindings/pwm/sophgo,sg2042-pwm.yaml
index e0e91aa237ec..11544b47c1b3 100644
--- a/Documentation/devicetree/bindings/pwm/sophgo,sg2042-pwm.yaml
+++ b/Documentation/devicetree/bindings/pwm/sophgo,sg2042-pwm.yaml
@@ -4,7 +4,7 @@
$id: http://devicetree.org/schemas/pwm/sophgo,sg2042-pwm.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
-title: Sophgo SG2042 PWM controller
+title: Sophgo SG2042/SG2044/CV1800B PWM controller
maintainers:
- Chen Wang <unicorn_wang@outlook.com>
@@ -18,6 +18,7 @@ allOf:
properties:
compatible:
enum:
+ - sophgo,cv1800b-pwm
- sophgo,sg2042-pwm
- sophgo,sg2044-pwm
--
2.53.0
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/3] pwm: sophgo-sg2042: add support for CV1800B
2026-11-17 12:57 [PATCH 0/3] Add PWM support for the Sophgo CV1800B Hiago De Franco
2026-11-17 12:57 ` [PATCH 1/3] dt-bindings: pwm: sophgo: add PWM controller for CV1800B Hiago De Franco
@ 2026-11-17 12:57 ` Hiago De Franco
2026-11-17 12:57 ` [PATCH 3/3] riscv: dts: sophgo: cv180x: add PWM controller nodes Hiago De Franco
2 siblings, 0 replies; 5+ messages in thread
From: Hiago De Franco @ 2026-11-17 12:57 UTC (permalink / raw)
To: Uwe Kleine-König, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Chen Wang, Inochi Amaoto, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Chen Wang, linux-pwm, devicetree, sophgo, linux-kernel,
linux-riscv
The CV1800B SoC embeds four instances of a PWM controller derived from
the one found on the SG2042 and SG2044 SoCs. The register layout is
mostly the same, but there are some differences handled by this patch:
- PERIOD and HLPERIOD are 30 bits wide and PERIOD must be strictly
greater than HLPERIOD. As a consequence, a 100% duty cycle cannot be
represented and the period must be at least two input clock cycles.
- The meaning of the POLARITY bit is inverted compared to the SG2044:
0 selects a low default level and 1 a high default level.
- A polarity change takes effect immediately, even while the channel is
running.
- New values written to HLPERIOD/PERIOD while the channel is running are
only latched after a 0 -> 1 -> 0 sequence on the PWMUPDATE bit.
- When the counter is stopped, the pin is parked at the level selected by
POLARITY. Emitting the inactive level would require changing POLARITY,
which would make the polarity read back from the hardware differ from the
requested one, so the driver disables the output instead.
Add a dedicated set of pwm_ops for the CV1800B to take these differences
into account, and update the module description accordingly. Update the
Kconfig entry to describe all the SoCs supported by the driver,
including the already supported SG2044.
This was tested on Milk-V Duo with a logic analyzer (GP4/pwm1 ch1).
Signed-off-by: Hiago De Franco <hfranco@baylibre.com>
---
drivers/pwm/Kconfig | 7 +-
drivers/pwm/pwm-sophgo-sg2042.c | 201 ++++++++++++++++++++++++++++++++++++++--
2 files changed, 199 insertions(+), 9 deletions(-)
diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 729776086879..877d5bfa0bb0 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -671,11 +671,12 @@ config PWM_SL28CPLD
will be called pwm-sl28cpld.
config PWM_SOPHGO_SG2042
- tristate "Sophgo SG2042 PWM support"
+ tristate "Sophgo SG2042/SG2044/CV1800B PWM support"
depends on ARCH_SOPHGO || COMPILE_TEST
help
- PWM driver for the PWM controller on Sophgo SG2042 SoC. The PWM
- controller supports outputing 4 channels of PWM waveforms.
+ PWM driver for the PWM controller on Sophgo SG2042, SG2044 and
+ CV1800B SoCs. Each controller supports 4 channels of PWM
+ waveforms.
To compile this driver as a module, choose M here: the module
will be called pwm_sophgo_sg2042.
diff --git a/drivers/pwm/pwm-sophgo-sg2042.c b/drivers/pwm/pwm-sophgo-sg2042.c
index 0b6461172e6a..45eb1871a127 100644
--- a/drivers/pwm/pwm-sophgo-sg2042.c
+++ b/drivers/pwm/pwm-sophgo-sg2042.c
@@ -1,21 +1,30 @@
// SPDX-License-Identifier: GPL-2.0
/*
- * Sophgo SG2042 PWM Controller Driver
+ * Sophgo SG2042/SG2044/CV1800B PWM Controller Driver
*
* Copyright (C) 2024 Sophgo Technology Inc.
* Copyright (C) 2024 Chen Wang <unicorn_wang@outlook.com>
*
* Limitations:
- * - After reset, the output of the PWM channel is always high.
+ * - After reset, the output of the SG2042 PWM channel is always high.
* The value of HLPERIOD/PERIOD is 0.
* - When HLPERIOD or PERIOD is reconfigured, PWM will start to
* output waveforms with the new configuration after completing
* the running period.
- * - When PERIOD and HLPERIOD is set to 0, the PWM wave output will
+ * - When PERIOD and HLPERIOD is set to 0, the SG2042 PWM wave output will
* be stopped and the output is pulled to high.
- * - SG2044 supports both polarities, SG2042 only normal polarity.
- * See the datasheet [1] for more details.
+ * - SG2044 and CV1800B support both polarities, SG2042 only normal polarity.
+ * - On CV1800B the pin is parked at the level selected by POLARITY while the
+ * counter is stopped. Emitting the inactive level would require changing
+ * POLARITY, so the driver disables the output (input mode) instead.
+ * - On CV1800B a polarity change takes effect immediately, even while the
+ * channel is running.
+ * - On CV1800B a 100% duty cycle is not representable. It is rounded down to
+ * one input clock cycle less than the period.
+ * - On CV1800B the period must be at least 2 input clock cycles.
+ * See the datasheets [1] and [2] for more details.
* [1]:https://github.com/sophgo/sophgo-doc/tree/main/SG2042/TRM
+ * [2]:https://github.com/sophgo/sophgo-doc/tree/main/SG200X/TRM
*/
#include <linux/clk.h>
@@ -44,10 +53,14 @@
#define SG2044_PWM_POLARITY 0x40
#define SG2044_PWM_PWMSTART 0x44
+#define SG2044_PWM_PWMUPDATE 0x4c
#define SG2044_PWM_OE 0xd0
#define SG2042_PWM_CHANNELNUM 4
+#define CV1800B_PWM_MAX_PERIOD GENMASK(29, 0)
+#define CV1800B_PWM_MIN_PERIOD 2
+
/**
* struct sg2042_pwm_ddata - private driver data
* @base: base address of mapped PWM registers
@@ -155,6 +168,14 @@ static void pwm_sg2044_set_outputen(struct sg2042_pwm_ddata *ddata, struct pwm_d
writel(pwmstart, ddata->base + SG2044_PWM_PWMSTART);
}
+static bool pwm_sg2044_get_outputen(struct sg2042_pwm_ddata *ddata,
+ struct pwm_device *pwm)
+{
+ u32 pwmstart = readl(ddata->base + SG2044_PWM_PWMSTART);
+
+ return !!(pwmstart & BIT(pwm->hwpwm));
+}
+
static void pwm_sg2044_set_outputdir(struct sg2042_pwm_ddata *ddata, struct pwm_device *pwm,
bool enabled)
{
@@ -208,6 +229,171 @@ static int pwm_sg2044_apply(struct pwm_chip *chip, struct pwm_device *pwm,
return 0;
}
+static int pwm_cv1800b_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
+ struct pwm_state *state)
+{
+ struct sg2042_pwm_ddata *ddata = pwmchip_get_drvdata(chip);
+ unsigned int chan = pwm->hwpwm;
+ u32 hlperiod_ticks;
+ u32 period_ticks;
+ u32 pwm_polarity;
+
+ /* PWMSTART is set to 1 while the channel is running. */
+ state->enabled = pwm_sg2044_get_outputen(ddata, pwm);
+
+ period_ticks = readl(ddata->base + SG2042_PWM_PERIOD(chan));
+ hlperiod_ticks = readl(ddata->base + SG2042_PWM_HLPERIOD(chan));
+
+ if (!period_ticks) {
+ /*
+ * No waveform is configured, so don't report a duty_cycle
+ * larger than the period.
+ */
+ state->enabled = false;
+ state->period = 0;
+ state->duty_cycle = 0;
+ } else {
+ if (hlperiod_ticks >= period_ticks)
+ hlperiod_ticks = period_ticks - 1;
+
+ state->period = DIV_ROUND_UP_ULL((u64)period_ticks * NSEC_PER_SEC,
+ ddata->clk_rate_hz);
+ state->duty_cycle = DIV_ROUND_UP_ULL((u64)hlperiod_ticks * NSEC_PER_SEC,
+ ddata->clk_rate_hz);
+ }
+
+ pwm_polarity = readl(ddata->base + SG2044_PWM_POLARITY);
+
+ /*
+ * Without a configured waveform POLARITY has no meaning, so report the
+ * neutral default instead of the register's reset value.
+ */
+ if (period_ticks && !(pwm_polarity & BIT(chan)))
+ state->polarity = PWM_POLARITY_INVERSED;
+ else
+ state->polarity = PWM_POLARITY_NORMAL;
+
+ return 0;
+}
+
+static void pwm_cv1800b_set_pwmupdate(struct sg2042_pwm_ddata *ddata, struct pwm_device *pwm,
+ bool enable)
+{
+ u32 pwm_update = readl(ddata->base + SG2044_PWM_PWMUPDATE);
+
+ if (enable)
+ pwm_update |= BIT(pwm->hwpwm);
+ else
+ pwm_update &= ~BIT(pwm->hwpwm);
+
+ writel(pwm_update, ddata->base + SG2044_PWM_PWMUPDATE);
+}
+
+static void pwm_cv1800b_set_polarity(struct sg2042_pwm_ddata *ddata, struct pwm_device *pwm,
+ bool high)
+{
+ u32 pwm_polarity = readl(ddata->base + SG2044_PWM_POLARITY);
+
+ /*
+ * POLARITY on CV1800B is the opposite of SG2044: 0 selects a low
+ * default level (HLPERIOD counts low cycles), 1 selects a high
+ * default level (HLPERIOD counts high cycles).
+ */
+ if (high)
+ pwm_polarity |= BIT(pwm->hwpwm);
+ else
+ pwm_polarity &= ~BIT(pwm->hwpwm);
+
+ writel(pwm_polarity, ddata->base + SG2044_PWM_POLARITY);
+}
+
+static int pwm_cv1800b_set_dutycycle(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
+{
+ struct sg2042_pwm_ddata *ddata = pwmchip_get_drvdata(chip);
+ u32 hlperiod_ticks;
+ u32 period_ticks;
+ u64 ticks;
+
+ /*
+ * Duration of High level (duty_cycle) = HLPERIOD x Period_of_input_clk
+ * Duration of One Cycle (period) = PERIOD x Period_of_input_clk
+ *
+ * Different from sg2042, cv1800b has max of 30 bits and PERIOD must be
+ * strictly greater than HLPERIOD. The shortest representable period is
+ * two input clock cycles; reject anything shorter instead of rounding
+ * it up.
+ */
+ ticks = mul_u64_u64_div_u64(ddata->clk_rate_hz, state->period, NSEC_PER_SEC);
+ period_ticks = min_t(u64, ticks, CV1800B_PWM_MAX_PERIOD);
+ if (period_ticks < CV1800B_PWM_MIN_PERIOD)
+ return -EINVAL;
+
+ ticks = mul_u64_u64_div_u64(ddata->clk_rate_hz, state->duty_cycle, NSEC_PER_SEC);
+ hlperiod_ticks = min_t(u64, ticks, period_ticks - 1);
+
+ dev_dbg(pwmchip_parent(chip), "chan[%u]: ENABLE=%u, PERIOD=%u, HLPERIOD=%u, POLARITY=%u\n",
+ pwm->hwpwm, state->enabled, period_ticks, hlperiod_ticks, state->polarity);
+
+ pwm_sg2042_config(ddata, pwm->hwpwm, period_ticks, hlperiod_ticks);
+
+ return 0;
+}
+
+static int pwm_cv1800b_apply(struct pwm_chip *chip, struct pwm_device *pwm,
+ const struct pwm_state *state)
+{
+ struct sg2042_pwm_ddata *ddata = pwmchip_get_drvdata(chip);
+ bool high = state->polarity == PWM_POLARITY_NORMAL;
+ bool running = pwm_sg2044_get_outputen(ddata, pwm);
+ int ret;
+
+ if (!state->enabled) {
+ /*
+ * While the counter is stopped the pin is parked at the level
+ * selected by POLARITY, i.e. at the level the waveform starts
+ * with. Emitting the inactive level would require changing
+ * POLARITY, which would make the polarity read back from the
+ * hardware differ from the requested one. Disable the output
+ * instead.
+ */
+ pwm_sg2044_set_outputen(ddata, pwm, false);
+ pwm_sg2044_set_outputdir(ddata, pwm, false);
+
+ return 0;
+ }
+
+ ret = pwm_cv1800b_set_dutycycle(chip, pwm, state);
+ if (ret)
+ return ret;
+
+ pwm_cv1800b_set_polarity(ddata, pwm, high);
+
+ if (!running) {
+ pwm_cv1800b_set_pwmupdate(ddata, pwm, false);
+ pwm_sg2044_set_outputdir(ddata, pwm, true);
+ pwm_sg2044_set_outputen(ddata, pwm, true);
+
+ return 0;
+ }
+
+ /*
+ * Write 1 and then 0 to PWMUPDATE[n] to latch new HLPERIOD/PERIOD
+ * values while the channel is running.
+ */
+ pwm_cv1800b_set_pwmupdate(ddata, pwm, true);
+ pwm_cv1800b_set_pwmupdate(ddata, pwm, false);
+
+ return 0;
+}
+
+static const struct sg2042_chip_data cv1800b_chip_data = {
+ .ops = {
+ .apply = pwm_cv1800b_apply,
+ .get_state = pwm_cv1800b_get_state,
+ },
+};
+
static const struct sg2042_chip_data sg2042_chip_data = {
.ops = {
.apply = pwm_sg2042_apply,
@@ -224,6 +410,9 @@ static const struct sg2042_chip_data sg2044_chip_data = {
static const struct of_device_id sg2042_pwm_ids[] = {
{
+ .compatible = "sophgo,cv1800b-pwm",
+ .data = &cv1800b_chip_data,
+ }, {
.compatible = "sophgo,sg2042-pwm",
.data = &sg2042_chip_data,
}, {
@@ -296,5 +485,5 @@ module_platform_driver(pwm_sg2042_driver);
MODULE_AUTHOR("Chen Wang");
MODULE_AUTHOR("Longbin Li <looong.bin@gmail.com>");
-MODULE_DESCRIPTION("Sophgo SG2042 PWM driver");
+MODULE_DESCRIPTION("Sophgo SG2042/SG2044/CV1800B PWM driver");
MODULE_LICENSE("GPL");
--
2.53.0
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 3/3] riscv: dts: sophgo: cv180x: add PWM controller nodes
2026-11-17 12:57 [PATCH 0/3] Add PWM support for the Sophgo CV1800B Hiago De Franco
2026-11-17 12:57 ` [PATCH 1/3] dt-bindings: pwm: sophgo: add PWM controller for CV1800B Hiago De Franco
2026-11-17 12:57 ` [PATCH 2/3] pwm: sophgo-sg2042: add support " Hiago De Franco
@ 2026-11-17 12:57 ` Hiago De Franco
2 siblings, 0 replies; 5+ messages in thread
From: Hiago De Franco @ 2026-11-17 12:57 UTC (permalink / raw)
To: Uwe Kleine-König, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Chen Wang, Inochi Amaoto, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti
Cc: Chen Wang, linux-pwm, devicetree, sophgo, linux-kernel,
linux-riscv
The CV180x/CV181x/SG200x SoCs provide four PWM controller instances at
0x03060000, 0x03061000, 0x03062000 and 0x03063000.
Add the corresponding nodes to the shared cv180x.dtsi, so that they are
available to every SoC including it, and keep them disabled by default
since the boards still need to describe how the outputs are wired.
Signed-off-by: Hiago De Franco <hfranco@baylibre.com>
---
arch/riscv/boot/dts/sophgo/cv180x.dtsi | 40 ++++++++++++++++++++++++++++++++++
1 file changed, 40 insertions(+)
diff --git a/arch/riscv/boot/dts/sophgo/cv180x.dtsi b/arch/riscv/boot/dts/sophgo/cv180x.dtsi
index d2ec70fd515e..c478e7eb549f 100644
--- a/arch/riscv/boot/dts/sophgo/cv180x.dtsi
+++ b/arch/riscv/boot/dts/sophgo/cv180x.dtsi
@@ -160,6 +160,46 @@ portd: gpio-controller@0 {
};
};
+ pwm0: pwm@3060000 {
+ compatible = "sophgo,cv1800b-pwm";
+ reg = <0x3060000 0x1000>;
+ #pwm-cells = <3>;
+ clocks = <&clk CLK_PWM>;
+ clock-names = "apb";
+ resets = <&rst RST_PWM0>;
+ status = "disabled";
+ };
+
+ pwm1: pwm@3061000 {
+ compatible = "sophgo,cv1800b-pwm";
+ reg = <0x3061000 0x1000>;
+ #pwm-cells = <3>;
+ clocks = <&clk CLK_PWM>;
+ clock-names = "apb";
+ resets = <&rst RST_PWM1>;
+ status = "disabled";
+ };
+
+ pwm2: pwm@3062000 {
+ compatible = "sophgo,cv1800b-pwm";
+ reg = <0x3062000 0x1000>;
+ #pwm-cells = <3>;
+ clocks = <&clk CLK_PWM>;
+ clock-names = "apb";
+ resets = <&rst RST_PWM2>;
+ status = "disabled";
+ };
+
+ pwm3: pwm@3063000 {
+ compatible = "sophgo,cv1800b-pwm";
+ reg = <0x3063000 0x1000>;
+ #pwm-cells = <3>;
+ clocks = <&clk CLK_PWM>;
+ clock-names = "apb";
+ resets = <&rst RST_PWM3>;
+ status = "disabled";
+ };
+
saradc: adc@30f0000 {
compatible = "sophgo,cv1800b-saradc";
reg = <0x030f0000 0x1000>;
--
2.53.0
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 1/3] dt-bindings: pwm: sophgo: add PWM controller for CV1800B
2026-11-17 12:57 ` [PATCH 1/3] dt-bindings: pwm: sophgo: add PWM controller for CV1800B Hiago De Franco
@ 2026-11-17 17:28 ` Conor Dooley
0 siblings, 0 replies; 5+ messages in thread
From: Conor Dooley @ 2026-11-17 17:28 UTC (permalink / raw)
To: Hiago De Franco
Cc: Uwe Kleine-König, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Chen Wang, Inochi Amaoto, Paul Walmsley,
Palmer Dabbelt, Albert Ou, Alexandre Ghiti, Chen Wang, linux-pwm,
devicetree, sophgo, linux-kernel, linux-riscv
[-- Attachment #1: Type: text/plain, Size: 75 bytes --]
Acked-by: Conor Dooley <conor.dooley@microchip.com>
pw-bot: not-applicable
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2026-11-17 17:28 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-17 12:57 [PATCH 0/3] Add PWM support for the Sophgo CV1800B Hiago De Franco
2026-11-17 12:57 ` [PATCH 1/3] dt-bindings: pwm: sophgo: add PWM controller for CV1800B Hiago De Franco
2026-11-17 17:28 ` Conor Dooley
2026-11-17 12:57 ` [PATCH 2/3] pwm: sophgo-sg2042: add support " Hiago De Franco
2026-11-17 12:57 ` [PATCH 3/3] riscv: dts: sophgo: cv180x: add PWM controller nodes Hiago De Franco
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox