* [PATCH 1/2] dt-bindings: arm: rockchip: Add Xunlong Orange Pi 5 Max
2024-10-31 3:14 [PATCH v2] arm64: dts: rockchip: Add Orange Pi 5 Max board Jimmy Hon
@ 2024-10-31 3:14 ` Jimmy Hon
2024-10-31 8:31 ` Krzysztof Kozlowski
2024-10-31 3:14 ` [PATCH 2/2] arm64: dts: rockchip: Add Orange Pi 5 Max board Jimmy Hon
1 sibling, 1 reply; 5+ messages in thread
From: Jimmy Hon @ 2024-10-31 3:14 UTC (permalink / raw)
To: Heiko Stuebner
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Ondrej Jirman,
devicetree, linux-arm-kernel, linux-rockchip, Jimmy Hon
Add devicetree binding for the Xunlong Orange Pi 5 Max board.
The Orange Pi 5 Max is a single board computer powered by the Rockchip
RK3588.
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
---
Documentation/devicetree/bindings/arm/rockchip.yaml | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index 1ef09fbfdfaf..8998cfe34fda 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -1001,6 +1001,11 @@ properties:
- const: xunlong,orangepi-3b
- const: rockchip,rk3566
+ - description: Xunlong Orange Pi 5 Max
+ items:
+ - const: xunlong,orangepi-5-max
+ - const: rockchip,rk3588
+
- description: Xunlong Orange Pi 5 Plus
items:
- const: xunlong,orangepi-5-plus
--
2.47.0
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH 2/2] arm64: dts: rockchip: Add Orange Pi 5 Max board
2024-10-31 3:14 [PATCH v2] arm64: dts: rockchip: Add Orange Pi 5 Max board Jimmy Hon
2024-10-31 3:14 ` [PATCH 1/2] dt-bindings: arm: rockchip: Add Xunlong Orange Pi 5 Max Jimmy Hon
@ 2024-10-31 3:14 ` Jimmy Hon
2024-11-09 18:23 ` Heiko Stübner
1 sibling, 1 reply; 5+ messages in thread
From: Jimmy Hon @ 2024-10-31 3:14 UTC (permalink / raw)
To: Heiko Stuebner
Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Ondrej Jirman,
devicetree, linux-arm-kernel, linux-rockchip, Jimmy Hon
The RK3588 Single Board Computer includes
- eMMC
- microSD
- UART
- 2 PWM LEDs
- RTC
- RTL8125 network controller on PCIe 2.0x1.
- M.2 M-key connector routed to PCIe 3.0x4
- PWM controlled heat sink fan.
- 2 USB2 ports
- lower USB3 port
- upper USB3 port with OTG capability
- Mali GPU
- SPI NOR flash
- Mask Rom button
- Analog audio using es8388 codec via the headset jack and onboard mic
- HDMI0
the vcc5v0_usb30 regulator shares the same enable gpio pin as the
vcc5v0_usb20 regulator.
Signed-off-by: Jimmy Hon <honyuenkwun@gmail.com>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../dts/rockchip/rk3588-orangepi-5-max.dts | 887 ++++++++++++++++++
2 files changed, 888 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-max.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index fda1b980eb4b..f910414f0b34 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -129,6 +129,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-friendlyelec-cm3588-nas.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-jaguar.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-nanopc-t6.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-ok3588-c.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-orangepi-5-max.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-orangepi-5-plus.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-quartzpro64.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-rock-5-itx.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-max.dts b/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-max.dts
new file mode 100644
index 000000000000..d31b13f99fdc
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588-orangepi-5-max.dts
@@ -0,0 +1,887 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3588.dtsi"
+
+/ {
+ model = "Xunlong Orange Pi 5 Max";
+ compatible = "xunlong,orangepi-5-max", "rockchip,rk3588";
+
+ aliases {
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ adc-keys-0 {
+ compatible = "adc-keys";
+ /* BOOT_SARADC_IN0 */
+ io-channels = <&saradc 0>;
+ io-channel-names = "buttons";
+ keyup-threshold-microvolt = <1800000>;
+ poll-interval = <100>;
+
+ button-maskrom {
+ label = "Mask Rom";
+ linux,code = <KEY_SETUP>;
+ press-threshold-microvolt = <2000>;
+ };
+ };
+
+ amp_audio: audio-amplifier {
+ compatible = "simple-audio-amplifier";
+ /* PHONE_CTL */
+ enable-gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
+ };
+
+ analog-sound {
+ compatible = "simple-audio-card";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hp_detect>;
+ simple-audio-card,name = "rockchip,es8388";
+ simple-audio-card,aux-devs = <&_audio>;
+ simple-audio-card,bitclock-master = <&masterdai>;
+ simple-audio-card,format = "i2s";
+ simple-audio-card,frame-master = <&masterdai>;
+ simple-audio-card,hp-det-gpios = <&gpio3 RK_PD2 GPIO_ACTIVE_HIGH>;
+ simple-audio-card,mclk-fs = <256>;
+ /*TODO: SARADC_VIN3_HP_HOOK is used as MIC detection / key input */
+
+ simple-audio-card,routing =
+ "Headphones", "LOUT1",
+ "Headphones", "ROUT1",
+ "LINPUT1", "Microphone Jack",
+ "RINPUT1", "Microphone Jack",
+ "LINPUT2", "Onboard Microphone",
+ "RINPUT2", "Onboard Microphone";
+ simple-audio-card,widgets =
+ "Microphone", "Microphone Jack",
+ "Microphone", "Onboard Microphone",
+ "Headphone", "Headphones";
+
+ simple-audio-card,cpu {
+ sound-dai = <&i2s0_8ch>;
+ };
+
+ masterdai: simple-audio-card,codec {
+ sound-dai = <&es8388>;
+ system-clock-frequency = <12288000>;
+ };
+ };
+
+ fan: pwm-fan {
+ compatible = "pwm-fan";
+ cooling-levels = <0 70 75 80 100>;
+ fan-supply = <&vcc5v0_sys>;
+ /* FAN_CTL_H */
+ pwms = <&pwm9 0 50000 0>;
+ #cooling-cells = <2>;
+ };
+
+ hdmi0-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi0_con_in: endpoint {
+ remote-endpoint = <&hdmi0_out_con>;
+ };
+ };
+ };
+
+ pwm-leds {
+ compatible = "pwm-leds";
+
+ blue_led: led-1 {
+ color = <LED_COLOR_ID_BLUE>;
+ function = LED_FUNCTION_STATUS;
+ linux,default-trigger = "heartbeat";
+ max-brightness = <255>;
+ /* PWM_LED1 */
+ pwms = <&pwm4 0 25000 0>;
+ };
+
+ green_led: led-2 {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ linux,default-trigger = "heartbeat";
+ max-brightness = <255>;
+ /* PWM_LED2 */
+ pwms = <&pwm5 0 25000 0>;
+ };
+ };
+
+ /* PMIC_EXT_EN */
+ vcc_1v1_nldo_s3: vcc-1v1-ndlo-s3-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v1_nldo_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ /* pcie eth. not a real regulator. 33VAUX */
+ vcc_3v3_aux: vcc-3v3-aux-regulator {
+ compatible = "regulator-fixed";
+ /* Ethernet_power_en */
+ gpios = <&gpio0 RK_PD3 GPIO_ACTIVE_LOW>;
+ regulator-name = "33vaux";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <50000>;
+ vin-supply = <&vcc_3v3_s3>;
+ };
+
+ vcc3v3_pcie30: vcc3v3-pcie30-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ /* PCIE_PWREN_H */
+ gpios = <&gpio2 RK_PB6 GPIO_ACTIVE_HIGH>;
+ regulator-name = "vcc3v3_pcie30";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ startup-delay-us = <5000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ /* Regulator is enabled whenever vcc_1v8_s0 is on */
+ vcc_3v3_s0: vcc-3v3-s0-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3_s3>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc5v0_sys: vcc5v0-sys-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ /* Represents the vcc5v0_usb20 in the schematic */
+ /* Also represents the vcc5v0_usb30 in the schematic,
+ both regulators share the same enable gpio */
+ vcc5v0_host: vcc5v0-host-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ /* USB_HOST_PWREN */
+ gpios = <&gpio3 RK_PD5 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_host_pwren>;
+ regulator-name = "vcc5v0_host";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+
+ vcc5v0_usb30_otg: vcc5v0-usb30-otg-regulator {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ /* USB_OTG_PWREN */
+ gpios = <&gpio4 RK_PB3 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_otg_pwren>;
+ regulator-name = "vcc5v0_usb30_otg";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc5v0_sys>;
+ };
+};
+
+&combphy2_psu {
+ status = "okay";
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b2 {
+ cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_b3 {
+ cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu_s0>;
+ status = "okay";
+};
+
+&hdmi0 {
+ status = "okay";
+};
+
+&hdmi0_in {
+ hdmi0_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi0>;
+ };
+};
+
+&hdmi0_out {
+ hdmi0_out_con: endpoint {
+ remote-endpoint = <&hdmi0_con_in>;
+ };
+};
+
+&hdptxphy_hdmi0 {
+ status = "okay";
+};
+
+&i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0m2_xfer>;
+ status = "okay";
+
+ vdd_cpu_big0_s0: regulator@42 {
+ compatible = "rockchip,rk8602";
+ reg = <0x42>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu_big0_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_big1_s0: regulator@43 {
+ compatible = "rockchip,rk8603", "rockchip,rk8602";
+ reg = <0x43>;
+ fcs,suspend-voltage-selector = <1>;
+ regulator-name = "vdd_cpu_big1_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1050000>;
+ regulator-ramp-delay = <2300>;
+ vin-supply = <&vcc5v0_sys>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+};
+
+&i2c6 {
+ clock-frequency = <400000>;
+ status = "okay";
+
+ hym8563: rtc@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ /* RTC_INT_L */
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PC4 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <0>;
+ clock-output-names = "hym8563";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hym8563_int>;
+ wakeup-source;
+ };
+};
+
+&i2c7 {
+ status = "okay";
+
+ es8388: audio-codec@11 {
+ compatible = "everest,es8388";
+ reg = <0x11>;
+ clocks = <&cru I2S0_8CH_MCLKOUT>;
+ AVDD-supply = <&vcc_3v3_s0>;
+ DVDD-supply = <&vcc_1v8_s0>;
+ HPVDD-supply = <&vcc_3v3_s0>;
+ PVDD-supply = <&vcc_1v8_s0>;
+ assigned-clocks = <&cru I2S0_8CH_MCLKOUT>;
+ assigned-clock-rates = <12288000>;
+ #sound-dai-cells = <0>;
+ };
+};
+
+&i2s0_8ch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2s0_lrck
+ &i2s0_mclk
+ &i2s0_sclk
+ &i2s0_sdi0
+ &i2s0_sdo0>;
+ status = "okay";
+};
+
+/* phy2 */
+&pcie2x1l1 {
+ reset-gpios = <&gpio4 RK_PD4 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc_3v3_aux>;
+ status = "okay";
+};
+
+&pcie30phy {
+ status = "okay";
+};
+
+&pcie3x4 {
+ reset-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc3v3_pcie30>;
+ status = "okay";
+};
+
+&pinctrl {
+ hym8563 {
+ hym8563_int: hym8563-int {
+ rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ sound {
+ hp_detect: hp-detect {
+ rockchip,pins = <3 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ usb {
+ usb_host_pwren: usb-host-pwren {
+ rockchip,pins = <3 RK_PD5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ usb_otg_pwren: usb-otg-pwren {
+ rockchip,pins = <4 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+};
+
+&pwm4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm4m0_pins>;
+ status = "okay";
+};
+
+&pwm5 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pwm5m1_pins>;
+ status = "okay";
+};
+
+&pwm9 {
+ pinctrl-names = "active";
+ pinctrl-0 = <&pwm9m2_pins>;
+ status = "okay";
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8_s0>;
+ status = "okay";
+};
+
+&sdhci {
+ bus-width = <8>;
+ no-sdio;
+ no-sd;
+ non-removable;
+ max-frequency = <200000000>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ /* SDMMC_DET_L */
+ cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ max-frequency = <150000000>;
+ no-sdio;
+ no-mmc;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3_s3>;
+ vqmmc-supply = <&vccio_sd_s0>;
+ status = "okay";
+};
+
+&sfc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&fspim2_pins>;
+ status = "okay";
+
+ spi_flash: flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0x0>;
+ spi-max-frequency = <100000000>;
+ spi-rx-bus-width = <4>;
+ spi-tx-bus-width = <1>;
+ };
+};
+
+&spi2 {
+ assigned-clocks = <&cru CLK_SPI2>;
+ assigned-clock-rates = <200000000>;
+ num-cs = <1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
+ status = "okay";
+
+ pmic@0 {
+ compatible = "rockchip,rk806";
+ reg = <0x0>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+ <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+ spi-max-frequency = <1000000>;
+ system-power-controller;
+
+ vcc1-supply = <&vcc5v0_sys>;
+ vcc2-supply = <&vcc5v0_sys>;
+ vcc3-supply = <&vcc5v0_sys>;
+ vcc4-supply = <&vcc5v0_sys>;
+ vcc5-supply = <&vcc5v0_sys>;
+ vcc6-supply = <&vcc5v0_sys>;
+ vcc7-supply = <&vcc5v0_sys>;
+ vcc8-supply = <&vcc5v0_sys>;
+ vcc9-supply = <&vcc5v0_sys>;
+ vcc10-supply = <&vcc5v0_sys>;
+ vcc11-supply = <&vcc_2v0_pldo_s3>;
+ vcc12-supply = <&vcc5v0_sys>;
+ vcc13-supply = <&vcc_1v1_nldo_s3>;
+ vcc14-supply = <&vcc_1v1_nldo_s3>;
+ vcca-supply = <&vcc5v0_sys>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ rk806_dvs1_null: dvs1-null-pins {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs2_null: dvs2-null-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs3_null: dvs3-null-pins {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun0";
+ };
+
+ regulators {
+ vdd_gpu_s0: dcdc-reg1 {
+ regulator-name = "vdd_gpu_s0";
+ regulator-boot-on;
+ regulator-enable-ramp-delay = <400>;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_lit_s0: dcdc-reg2 {
+ regulator-name = "vdd_cpu_lit_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_log_s0: dcdc-reg3 {
+ regulator-name = "vdd_log_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <825000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_vdenc_s0: dcdc-reg4 {
+ regulator-name = "vdd_vdenc_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <825000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_ddr_s0: dcdc-reg5 {
+ regulator-name = "vdd_ddr_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <675000>;
+ regulator-max-microvolt = <900000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+ };
+
+ vdd2_ddr_s3: dcdc-reg6 {
+ regulator-name = "vdd2_ddr_s3";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_2v0_pldo_s3: dcdc-reg7 {
+ regulator-name = "vdd_2v0_pldo_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <2000000>;
+ };
+ };
+
+ vcc_3v3_s3: dcdc-reg8 {
+ regulator-name = "vcc_3v3_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vddq_ddr_s0: dcdc-reg9 {
+ regulator-name = "vddq_ddr_s0";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s3: dcdc-reg10 {
+ regulator-name = "vcc_1v8_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcca_1v8_s0: pldo-reg1 {
+ regulator-name = "vcca_1v8_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc_1v8_s0: pldo-reg2 {
+ regulator-name = "vcc_1v8_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdda_1v2_s0: pldo-reg3 {
+ regulator-name = "vdda_1v2_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca_3v3_s0: pldo-reg4 {
+ regulator-name = "vcca_3v3_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd_s0: pldo-reg5 {
+ regulator-name = "vccio_sd_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s3_pldo6: pldo-reg6 {
+ regulator-name = "vcc_1v8_s3_pldo6";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_0v75_s3: nldo-reg1 {
+ regulator-name = "vdd_0v75_s3";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdd_ddr_pll_s0: nldo-reg2 {
+ regulator-name = "vdd_ddr_pll_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+ };
+
+ hdmi_vdda0v85_s0: nldo-reg3 {
+ regulator-name = "hdmi_vdda0v85_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ /*
+ * The schematic mentions that actual setting
+ * should be 0.8375V. RK3588 datasheet specifies
+ * maximum as 0.825V. So we set datasheet max
+ * here.
+ */
+ regulator-min-microvolt = <825000>;
+ regulator-max-microvolt = <825000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v85_s0: nldo-reg4 {
+ regulator-name = "vdda_0v85_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_0v75_s0: nldo-reg5 {
+ regulator-name = "vdd_0v75_s0";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+&tsadc {
+ status = "okay";
+};
+
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ phy-supply = <&vcc5v0_usb30_otg>;
+ status = "okay";
+};
+
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy1_otg {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&u2phy2 {
+ status = "okay";
+};
+
+&u2phy2_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&u2phy3 {
+ status = "okay";
+};
+
+&u2phy3_host {
+ phy-supply = <&vcc5v0_host>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-0 = <&uart2m0_xfer>;
+ status = "okay";
+};
+
+&usbdp_phy0 {
+ status = "okay";
+};
+
+&usbdp_phy1 {
+ status = "okay";
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
+
+&usb_host0_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usb_host1_ehci {
+ status = "okay";
+};
+
+&usb_host1_ohci {
+ status = "okay";
+};
+
+&usb_host1_xhci {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vop {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi0: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi0_in_vp0>;
+ };
+};
--
2.47.0
^ permalink raw reply related [flat|nested] 5+ messages in thread