Re: [PATCH 1/3] arm64: dts: qcom: eliza: Describe the ADSP and USB related nodes

[Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>]

On 4/29/26 3:57 AM, Krishna Kurapati PSSNV wrote:
> On Tue, Apr 28, 2026 at 2:54 PM Konrad Dybcio
> <konrad.dybcio@oss.qualcomm.com> wrote:
>>
>> On 4/28/26 7:46 AM, Krishna Kurapati PSSNV wrote:
>>> On Wed, Apr 22, 2026 at 3:55 PM Abel Vesa <abel.vesa@oss.qualcomm.com> wrote:
>>>>
>>>> On 26-04-22 12:09:31, Konrad Dybcio wrote:
>>>>> On 4/22/26 11:41 AM, Abel Vesa wrote:
>>>>>> On 26-03-31 15:37:08, Konrad Dybcio wrote:
>>>>>>> On 3/31/26 12:37 PM, Abel Vesa wrote:
>>>>>>>> Describe the ADSP remoteproc node along with its dependencies, including
>>>>>>>> the IPCC mailbox, AOSS QMP and SMP2P links used for communication.
>>>>>>>>
>>>>>>>> The Eliza SoC features a USB 3.1 Gen 2 controller connected to a QMP
>>>>>>>> combo PHY and an SNPS eUSB2 PHY. Describe them.
>>>>>>>>
>>>>>>>> Signed-off-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
>>>>>>>> ---
>>>>>>>
>>>>>>> [...]
>>>>>>>
>>>>>>>> +         usb_hsphy: phy@88e3000 {
>>>>>>>> +                 compatible = "qcom,eliza-snps-eusb2-phy",
>>>>>>>> +                              "qcom,sm8550-snps-eusb2-phy";
>>>>>>>> +                 reg = <0x0 0x088e3000 0x0 0x154>;
>>>>>>>> +                 #phy-cells = <0>;
>>>>>>>> +
>>>>>>>> +                 clocks = <&rpmhcc RPMH_CXO_CLK>;
>>>>>>>
>>>>>>> This is TCSR_USB2_CLKREF_EN
>>>>>>
>>>>>> Good point. Will fix.
>>>>>>
>>>>>>>
>>>>>>>
>>>>>>>> +         usb: usb@a600000 {
>>>>>>>> +                 compatible = "qcom,eliza-dwc3", "qcom,snps-dwc3";
>>>>>>>
>>>>>>> Does the device suspend and resume successfully?
>>>>>>
>>>>>> Well, tested with pm_test devices and it does suspend and resume
>>>>>> successfully, but there is this:
>>>>>>
>>>>>> [   54.584126] dwc3-qcom a600000.usb: port-1 HS-PHY not in L2
>>>>>>
>>>>>> But if I'm not mistaken, this is valid accross all SNPS eUSB2 PHYs, on
>>>>>> all platforms that have them.
>>>>>
>>>>> Well it's not fatal, but ideally this wouldn't be there. Maybe you're missing
>>>>> some DWC quirk in the list, although it seems pretty long already. Perhaps
>>>>> Wesley would know more.
>>>>
>>>> + Wesley
>>>>
>>>
>>> As per HPG and downstream, this is what needs to be done while entering suspend:
>>>
>>> 1. Clear PWR_EVNT_LPM_IN_L2_MASK bit of pwr_evnt_irq_stat_reg
>>> 2. Clear PWR_EVNT_LPM_OUT_L2_MASK bit of pwr_evnt_irq_stat_reg
>>> 3. Set the following bits in the pwr_evnt_irq_stat_reg:
>>>  a)  DWC3_GUSB2PHYCFG_ENBLSLPM  and  DWC3_GUSB2PHYCFG_SUSPHY
>>
>> In case that's related, most platforms (including this one), set
>> snps,dis_enblslpm_quirk which prevents the first bit from being set
>>
>> Likewise, snps,dis_u2_susphy_quirk for the second one
>>
>> (although it looks like setting these bits is currently
>> unconditional upon suspend in HOST mode?)
>>
>>
>> As for the sequence you mentioned, I believe the diff below should be
>> OK - although it _really_ just adds some delay vs the current state,
>> since the bits are cleared in the resume call
>>
>> diff --git a/drivers/usb/dwc3/dwc3-qcom.c b/drivers/usb/dwc3/dwc3-qcom.c
>> index f43f73ac36ff..e7b1775b7207 100644
>> --- a/drivers/usb/dwc3/dwc3-qcom.c
>> +++ b/drivers/usb/dwc3/dwc3-qcom.c
>> @@ -12,6 +12,7 @@
>>  #include <linux/module.h>
>>  #include <linux/kernel.h>
>>  #include <linux/interconnect.h>
>> +#include <linux/iopoll.h>
>>  #include <linux/platform_device.h>
>>  #include <linux/phy/phy.h>
>>  #include <linux/usb/of.h>
>> @@ -344,10 +345,18 @@ static int dwc3_qcom_suspend(struct dwc3_qcom *qcom, bool wakeup)
>>                 return 0;
>>
>>         for (i = 0; i < qcom->num_ports; i++) {
>> -               val = readl(qcom->qscratch_base + pwr_evnt_irq_stat_reg[i]);
>> -               if (!(val & PWR_EVNT_LPM_IN_L2_MASK))
>> +               /* Wait for the PHYs to go into L2 */
>> +               ret = readl_poll_timeout(qcom->qscratch_base + pwr_evnt_irq_stat_reg[i],
>> +                                        val, val & PWR_EVNT_LPM_IN_L2_MASK,
>> +                                        10, 3 * USEC_PER_MSEC);
>> +
>> +               if (ret == -ETIMEDOUT)
>>                         dev_err(qcom->dev, "port-%d HS-PHY not in L2\n", i + 1);
>>         }
>> +
> 
> 
> I think its best to set the DWC3_GUSB2PHYCFG_ENBLSLPM and
> DWC3_GUSB2PHYCFG_SUSPHY here as well based on quirks before polling
> for the irq_stat register.

Hm, it seems like the dwc3 core layer only does so in the suspend
path if dr_mode = "host"?

Konrad